MasterSeal® TC 254

Two component polyurethane UV- resistant protective traffic coating

DESCRIPTION TYPICAL PROPERTIES

MasterSeal TC 254 is a two component elastomeric
pigmented polyurethane coating designed for application Mixed density 1.30-1.40gm/cm³
in heavily trafficked areas. It provides a UV-resistant, depending on color
hard-elastic surface resistant to chemicals and abrasion. Curing at 20°C and Capable of bearing
Unlike conventional moisture curing polyurethane 60% rel. atm. hum. loads at 96 hours
coatings MasterSeal TC 254 can be applied at higher
thicknesses without foaming. tack free time 30 mins. approx.
Open to traffic 8 hours approx
PRIMARY USES
The high abrasion resistance of MasterSeal TC 254 Reaction temperatures from +5°C to +40°C
combined with its elasticity makes it suitable for use in
car parks both indoors and out. MasterSeal TC 254 may Rel. atm. humidity 40-90%
be used in the following applications: Tensile strength ASTM D412 approx. 4.5N/mm²
NB: This gives examples only and does not constitute a Breaking elongation approx. 200%
full and comprehensive list. For further information on ASTM D 412
application possibilities contact Saudi Master Builders
Solutions Technical Department Taber Abrasion Less than 50 mg/ 1000
– Pedestrian walk ways (ASTM D 4060) revolution
– Light engineering workshops
– Car parks.
– Vehicle ramps and Traffic aisles GUIDE TO APPLICATION

ADVANTAGES PREPARATION
– Excellent impact and abrasion resistance Remove laitance, weak or friable concrete and all
– Elastomeric contaminants that could affect the bond to the substrate.
– UV & weather resistant Suitable preparation includes light grit blasting, surface
– Good chemical and oil resistance grinding etc. Surface defects should be repaired using
MasterTop 2200 or other suitable repair compounds
COLORS from the MasterBrace or MasterEmaco range
The Master Builders Solutions standard colors for
MasterSeal TC 254 are: PRIMING
Basalt Grey, Black Grey, May Green, Oxide Red, Mix and apply MasterTop P 650 surface conditioner to
Brilliant Blue the prepared dust free surface at approximately 0.15-
(Further colors are available on request). 0.3kg/m². Into the wet primer, scatter a 0.6-2.0kg/m²
MasterTop SR 3. Note: If a smooth surface finish is
PACKAGING required, omit the aggregate scatter. Allow to cure.
MasterSeal TC 254 is available in 24 kg units.
APPLICATION
COVERAGE MasterSeal TC 254 should be stirred before use to
From 0.3kg/m² per coat please refer to Master Builders ensure uniformity of color. Apply by roller, squeegee or
Solutions Method Statements for project specific airless spray to the primed tack free surface. Apply at
coverages. the rate of 0.8-1.2kg/m² (in 2-3 coats). MasterSeal TC
254 can be applied as a single coat, or as a multi coat
sandwich system incorporating aggregates to give a slip
resistant finish.

MasterSeal® TC 254 1/2

MasterSeal® TC 254
Two component polyurethane UV- resistant protective traffic coating

When applying as a top coat or part of a multi coat NOTE

system, do not exceed the maximum overcoating times Field service, where provided, does not constitute
of the previous coating. supervisory responsibility. For additional information
Apply a minimum of two coats. contact your local Master Builders Solutions
Do not apply when the humidity exceeds 90%. Ensure representative.
that the substrate temperature is 3°C higher than the Master Builders Solutions reserves the right to have the
dew point. true cause of any difficulty determined by accepted test
If a maintenance coat has to be applied, thoroughly methods.
wash the existing MasterSeal TC 254. Allow to dry, then
immediately prior to overcoating, wipe the surface with a QUALITY AND CARE
cloth dampened with MasterTop THN 2.
All Master Builders Solutions Products are manufactured
under a management system independently certified to
CHEMICAL RESISTANCE conform to the requirements of the quality,
MasterSeal TC 254 is resistant to acids and alkalis of environmental and occupational health and safety
medium concentrations, mineral oil products and standards of ISO 9001 and Master Builders Solutions
solvents. Contact your local Master Builders Solutions ESHQ recommendations.
office for specific details. * Properties listed are based on laboratory controlled
tests.
SHELF LIFE AND STORAGE ® = Registered trademark of the MBCC-Group in many
The shelf life is 6 months in unopened drums in cool and countries
dry conditions.
Once a drum has been opened, its contents should, if CONTACT
possible, be used up completely since surface skinning Should you require any further information, please do
will form on any remaining quantities. not hesitate to contact us:

SAFETY PRECAUTIONS www.master-builders-solutions.com/en-sa

Avoid any inhalation of vapour and contact with skin. [email protected]
Wear protective gloves and protective goggles. In case M: +966 13 853 8600
of skin contact, rinse immediately with soap and water.
In case of eye contact, bathe eyes with water at once, Master Builders Solutions Saudi Arabia for
then consult a doctor. Do not eat, do not smoke and do Manufacturing LLC.
not use an open flame when handling the product. P.O. Box 1884, Al Khobar, KSA

The technical information and application advice given in this Master Builders Solutions publication are based on the present state of
our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be made as to a
STATEMENT OF
product's suitability for a particular use or application and no warranty as to its accuracy, reliability or completeness either expressed
RESPONSIBILITY
or implied is given other than those required by law. The user is responsible for checking the suitability of products for their intended
use.
Disclaimer:
In view of widely varying site conditions and fields of application of our All descriptions, drawings, photographs, data, ratios, weights i.e.
products, this technical data sheet is meant to provide general application stated herein can be changed without advance notice and do not
guidelines only. This information is based on our present knowledge and represent the condition of the product as stipulated by contract. It is
experience. The customer is not released from the obligation to conduct the sole responsibility of the recipient of our products to observe
careful testing of suitability and possible application for the intended use. possible proprietary rights as well as existing laws and provisions. The
The customer is obliged to contact the technical help-line for fields of reference of trade names of other companies is no recommendation
application not expressly stated in the technical data sheet under "Fields and does not exclude the use of products of similar type. Our
of Application". Use of the product beyond the fields of application as information only describes the quality of our products and services
stated in the technical data sheet without previous consultation with and is no warranty. Liability is accepted for incomplete or incorrect
Master Builders Solutions and possible resulting damages are in the sole particulars in our data sheets only in the event of intent or gross
responsibility of the customer. negligence, without prejudice to claims under product liability laws.

MasterSeal® TC 254 2/2 Master Builders Solutions Saudi / 08-15 / 04-17