ABS submersible wastewater pump AS 0530-0841

Robust, reliable submersible pumps from 1 to 3 kW for pumping

clear water, wastewater and sewage from buildings and sites in Type tested
and monitored

domestic and commercial areas in accordance with EN 12050-1.

Applications
AS submersible pumps have been designed for the economic and
reliable pumping of wastewater and sewage, and can be used for
fixed applications with ABS automatic coupling system or as port-
able units.
* The 2-inch version is especially suitable for pumping wastewater
from underground garages.
* With vortex hydraulics the AS is particularly suitable for fluids
containing fibrous or abrasive matter and for sewage.
* The Contrablock hydraulic system is suitable for larger propor-
tions of solid or fibrous matter.
* Maximum allowable temperature of the medium is 40 °C, or
short term to 60 °C (max. 5 minutes).

Construction
The water pressure-tight, encapsulated fully flood-proof motor Identification Code: e.g. AS 0840 S 12/2 Ex
and the pump section form a compact, robust, unit construction. Hydraulics:
AS .......... Product range
Motor 08 ........... Discharge outlet DN (cm)
Single-phase 220-240 V and three-phase 400 V, 50 Hz, 2-pole (2900 40 ........... Hydraulic number
r/min) and 4-pole (1450 r/min). Insulation class F; protection type Motor:
IP 68. Ex protection to Ex d IIB T4 and FM international standards. S ........... Modular motor version
Consult ABS for Ex usage with frequency inverters. 12 .......... Motor power P2 kW x 10
2 ............ Number of poles
Bearings Ex .......... Explosive-proof
The stainless steel motor shaft is supported in lubricated-for-life
ball bearings.

Shaft sealing
Between motor and hydraulic section by means of a high quality Features
sealing unit using a silicon carbide mechanical seal, independent * Hydraulic design with Contrablock system or vortex impellers.
of direction of rotation and resistant to temperature shock. Seal at * High reliability even under long term operating conditions.
motor side is by oil lubricated lip seal. * For wastewater and sewage containing solid or fibrous particles.
* In standard or Ex-versions.
Discharge * Option of automatic seal and temperature monitoring. Ex version
AS 0530: G 2” internal thread (DN 50) with temperature monitoring as standard.
AS 0630 to 0641: radial slot DN 65 flange * Available for transportable or fixed installation.
AS 0830, 0831, 0840 & 0841: radial slot DN 80 flange

Temperature monitoring
TCS (Thermo-Control-System) with thermal sensors in the stator
to switch off the pump in the case of overheating and switch on
automatically after cooling down (option on standard AS).

Seal monitoring
DI system consisting of a sensor in the motor and oil chambers Materials
which signals an inspection alert if there is leakage at the shaft Description Material
seals (option on standard AS; not in oil chamber on Ex version).
Motor Housing Cast iron EN-GJL-250
Hydraulics Rotor Shaft Stainless steel 1.4021 (AISI 420)
AS 0530, 0630, 0631, 0830, 0831: vortex, open, recessed four-vane Volute Cast iron EN-GJL-250
impeller.
AS 0641, 0840, 0841: Contrablock, open single-vane impeller with Impeller Cast iron EN-GJL-250
spiral bottom plate. Bottom plate Cast iron EN-GJL-250
Fasteners Stainless steel 1.4401 (AISI 316)
Technical Data
AS Solids Discharge * Rated   Motor power ** Rated Speed Weight ***
size voltage         (kW) current
(mm)    (V)   P1             P2    (A) (r/min)     (kg)
0530  S12/2W (1   40    G 2” 220-240 1~   1.77          1.20   8.22   2900      31
          S12/2D   40    G 2” 400 3~   1.69          1.20   3.29   2900      31
          S17/2D   40    G 2” 400 3~   2.31          1.70   3.97   2900      34
          S26/2D   40    G 2” 400 3~   3.43          2.60   5.64   2900      40
0630  S10/4W (1   60    DN 65 220-240 1~   1.69          1.00   7.49   1450      37
          S13/4D   60    DN 65 400 3~   1.93          1.30   3.60   1450      37
          S22/4D   60    DN 65 400 3~   2.88          2.20   5.15   1450      43
0631  S12/2W (1   40    DN 65 220-240 1~   1.77          1.20   8.22   2900      35
          S12/2D   40    DN 65 400 3~   1.69          1.20   3.29   2900      35
          S17/2W (1   40    DN 65 220-240 1~   2.36          1.65 10.60   2900      35
          S17/2D   40    DN 65 400 3~   2.31          1.70   3.97   2900      35
          S30/2D   40    DN 65 400 3~   3.74          3.00   6.23   2900      42
0641  S30/2D   45    DN 65 400 3~   3.74          3.00   6.23   2900      41
0830  S10/4W (1
  60    DN 80 220-240 1~   1.69          1.00   7.49   1450      40
          S13/4D   60    DN 80 400 3~   1.93          1.30   3.60   1450      37
          S22/4D   60    DN 80 400 3~   2.88          2.20   5.15   1450      43
0831  S22/4D   80    DN 80 400 3~   2.88          2.20   5.15   1450      45
0840  S12/2W (1   30    DN 80 220-240 1~   1.77          1.20   8.22   2900      33
          S12/2D   30    DN 80 400 3~   1.69          1.20   3.29   2900      33
          S17/2D   30    DN 80 400 3~   2.31          1.70   3.97   2900      33
          S26/2D   30    DN 80 400 3~   3.43          2.60   5.64   2900      39
0841  S13/4D   80    DN 80 400 3~   1.93          1.30   3.60   1450      41
          S22/4D   80    DN 80 400 3~   2.88          2.20   5.15   1450      56
* G = internal thread, DN = flange (1
  Start and Run capacitor to the following specification required in control panel.
** P1 = Power at mains;  P2 = Power at motor shaft;     Start: 125-160µF.   Run: 40µF (2x20µF) for S10/4W, 30µF for S12/2W & S17/2W
*** Weight with 10 m cable.  Cable size: Standard = 4G1.5, Ex = 7G1.5     The recommended start time for the motors is two seconds.

Dimensions (mm)
AS A B C D E F G H J K L M N O P
0530  S12/2 & 17/2 432 293 331 160 236 125 175 133 100 18 155 n.a. 20 n.a. n.a.
           S26/2 444 293 331 160 236 125 175 133 100 18 155 n.a. 20 n.a. n.a.
0630  S10/4 & 13/4 437 309 348 157 294 140 247 147   57 18 245 195 15 132 40
           S22/4 450 309 348 157 294 140 247 147   57 18 245 195 15 132 40
0631  S12/2 & 17/2 409 305 346 160 237 140 247 145   54 18 245 195 15 132 40
           S30/2 421 305 346 160 237 140 247 145   54 18 245 195 15 132 40
0641  S30/2 428 308 346 160 237 140 247 148   54 18 245 195 15 132 40
0830  S10/4 & 13/4 437 307 408 160 294 200 342 147   88 18 275 195 20 182 25
           S22/4 450 307 408 160 294 200 342 147   88 18 275 195 20 182 25
0831  S22/4 470 397 445 240 312 200 340 157   88 18 275 195 20 182 25
0840  S12/2 & 17/2 418 280 379 130 210 200 342 148   88 18 275 195 20 182 25
           S26/2 430 280 379 130 210 200 342 148   88 18 275 195 20 182 25
0841  S13/4 473 397 445 240 312 200 340 157   88 18 275 195 20 182 25
           S22/4 485 397 450 240 312 200 340 157   88 18 275 195 20 182 25

* Lowest switch-off level; minimum switch-on level must be at least 100 mm higher.    
** Elbow not supplied.
Performance Curves
AS 0530 AS 0630 and 0830

AS 0631 and 0641 AS 0831

12

11

10

8
S2
7 2/
4
S2

6
2/
4

3
Ø2
05

2
Ø1
98

20 40 60 80 100 120 140

8 16 24 32

AS 0840 AS 0841
12

11

10

9
S2
8 2/
4
7

6 S1
3/
4
5 S1
3/
4
4
S1
3 3/
4 Ø1
Ø1 Ø1 96
2 Ø1 61 77
52
1

20 40 60 80 100 120 140

8 16 24 32

H = Total Head; Q = Discharge Volume.    Curves to ISO 9906 (60 Hz available on request)    N.B. please use the ABSEL program to validate pump selection.     
Accessories
Description Size Part no. AS

Fixed installation Pedestal (cast iron EN-GJL-250)

with ABS Automatic threaded (with fixing bolts and transition piece) 2” without bend 62320560 0530
Coupling System flange (with fixing bolts) DN 65: 90º cast bend 62320673 0630-0641
flange (with fixing bolts) DN 80 without bend 62320557 0830 & 0840
flange (fixing bolts not included) DN 80: 90º cast bend 62320649 0830/31/40/41
flange (with plug/clamp connection DN 80: 90º cast bend 62320650 0830/31/40/41
and fixing bolts)
Fasteners (galvanized steel)
bolts and gasket (bracket to pump) 62610632 0830/31/40/41
anchor bolts (pedestal to base) 62610775 0830/31/40/41
Guide Rail (galvanized steel) 1¼” x 1 m 31380007 0530-0641
1¼” x 2 m 31380008
1¼” x 3 m 31380009
1¼” x 4 m 31380010
1¼” x 5 m 31380011
Chain Kit (galvanized steel) 3m 61265065 0530-0841
4m 61265093
6m 61265069
7m 61265096
Chain Kit (stainless steel) 3m 61265081 0530-0841
4m 61265099
6m 61265085
7m 61265102

Fixed installation - Pump Support Kit (EN-GJL-250) 61825001 0831 & 0841
dry well: (horizontal) head and volute supports with
fixing bolts and vibration damper
                 (vertical) Ground Support Stand 61355002 0831 & 0841

Transportable Ground Support Stand 42895016 0630 & 0830

installation 61355012 0631 & 0641
61350526 0831 & 0841
Discharge Elbow (EN-GJL-250)
flange to thread DN 80 to G 2½” 31090131 0840
flange to STORZ coupling DN 80 to G 2½” 62665074

Adaptor (galvanized steel) DN 65 to DN 80 21405002 0630 & 0631

2011-01-25 | We reserve the rights to alter specifications due to technical developments.

General Non-return Ball Valve (EN-GJL-250)
internal thread G 2” 61400527 0530
internal thread with inspection hatch G 2½” 61400543 0630-0641
flange with inspection hatch and venting DN 80 61400534 0830/31/40/41
flange with inspection hatch DN 80 61400523 0830/31/40/41

Gate Valve (brass) G 2” 14040007 0530

                   (EN-GJL-250) DN 80 61420500 0830, 0831,
0840 & 0841

Design
1. Ball bearings; lubricated-for-life 1

2. Watertight cable entry

3. Motor with thermal sensor in 2

    air-filled motor housing
3
4. Oil chamber with seal monitoring
4
5. Sic/Sic mechanical seal 5
6
6. Contrablock (featured) or vortex hydraulics