Propeller Installation Diagram

Remove the propeller cap and screw from the propeller,

then remove the propeller.
To install the propeller, sim at the hole and press the
propeller down to the end, then lock the propeller by
attached screw. Press down the propeller cap.

Picture 16

Propeller Guard Installation Diagram

Install the propeller guard to the drone and lock
the propeller guard by attached screws.
Remove the screw from the propeller guard and
pull out the propeller guard with moderate force.

Note: Fly the drone without the propeller guard

can improve the power and flight time. Picture 17

Camera Installation Diagram

To install the camera, aim at the buckle in the
drone and push the camera with moderate force.

To remove the camera, pull out the camera from

the buckle.

Picture 18

Landing Gear Installation Diagram

To install the Landing Gear, insert the Landing
Gear’s pillars into the drone body holes with
moderate force as the diagram shown. Then
lock the Landing Gear by attached screw.
To remove the Landing Gear, remove the screw
first and then pull out the Landing Gear with
moderate force.
Note: Please ensure the Landing Gear can stand
firm on the ground. Or the flight stability
would be effected. Picture 19

13
Instruction for Receiving Board
The drone works well only when the installation direction of the receiving board
and the connection position of the wires the same as below picture:
Front

Left-front light wire 1 5 Right-front light wire

Left-front motor wire 2 Blue wire Black wire
6 Right-front motor wire
(red and blue wire) Red wire White wire (black and white wire)
Left Right
Left-rear motor wire 3 White wire Red wire
7 Right-rear motor wire
(black and white wire) Black wire Blue wire (red and blue wire)
Left-rear light wire Right-rear light wire

Left-rear light wire 4 8 Right-rear light wire

9
Switch Wire Barometer
Picture 20 Rear

Operation Instruction for Mobile Phone WiFi

Download and Install the APP: Flyingsee
The APP is suitable for mobile phone with iOS or Android system, please
download from the mobile phone software store:
1. For mobile phone with iOS system, please
search Flyingsee in APP Store.
2. For mobile phone with Android system, please
search Flyingsee in Google Play. ANDROID APP ON Available on the
App Store

3. Scan the QR code in the right side or the QR code

in the color box to download Flyingsee.

Frequency Pairing between Mobile Phone and Drone WiFi:

1. Install the battery to the mounted box and power on the drone. Put the drone
on the flat surface.
2. Enter “set up” of the mobile phone, turn on WiFi (WLAN) and choose
udirc-WiFi-..., return to desktop after successful connection.

3. Click the icon Flyingsee and click to enter the remote control interface for
real time transmission.

Flyingsee

Click Home Page

14
 EMERGENCY EMERGENCY

00:00 H:100m 100% 00:00 H:100m 100%

Real-time Transmission Interface Virtual Control Interface

Picture 21 Picture 22

Click to enter Virtual Control Interface as Picture 22

At this time the drone LED lights change from flash to solid
bright, which indicates successful frequency pairing and the
drone is ready to be controlled via APP.

Introduction for APP Control Menu

Home Page
Click this icon and return to the home page.

Virtual Reality Mode

Click this icon to enter virtual reality mode (available for VR headset). Click this
icon again to exit from virtual reality mode.
Tip: Do not use the emergency stop function unless in emergency situation.

Flight Route Setting Mode

Click this icon and it turns red. Draw a flight route in the right area. The drone will
fly according to the flight route. Click the icon again to exit from Flight Route Setting
Mode. The icon turns white.

Emergency Stop
The icon is red by default. Click this icon and the propellers will stop immediately.
The drone will fall down to the ground straightly.

TF Card
If there is a TF Card in the drone, the icon will show as .If there is no TF Card
in the drone, the icon will show as .

Remote Control Signal

To show the drone’s WiFi signal strength.

15
 Setting
Click this icon to set some parameters, and click again to exit.
SETING

Click “Save” to save the trim setting.

Click “Reset” for factory reset.
Trimming Save Reset

Transmission quality 480P

Gravity Induction Mode

Click icon to enter Gravity Induction Mode, which is only available for flying
left / right and forward / backward.

If the mobile phone shakes to the

left / right, the Right Ball will move
accordingly causing the drone to fly
left / right.

If the mobile phone shakes to

forward / backward, the Right Ball
will roll forward / backward, causing
the drone to fly forward / backward.

Video
Click this icon to record video. The recording time will show at the bottom of the
screen. Click this icon again to finish recording.

Photo
Click this icon to take photo.

Heading Hold Mode

Click this icon and it turns red, which indicates that the drone enter Heading Hold
Mode. Click again to exit from Heading Hold Mode. The icon turns white.

High / Low Speed Mode

By default, the drone is in Low Speed Mode “L”. Click this icon and then click “H”
to enter High Speed Mode.

Flip Mode
Click this icon, the drone will do 360° flip and the icon will turn red shortly.

16
 One Button Landing
Click this icon and the icon turns red, the drone will fly down slowly and land on
the ground. All propellers also will stop.

One Button Take Off

Click this icon and it turns red shortly. The drone will fly up automatically and
stay flying at an altitude of 1.2 meters.

Hold Throttle

Move the Left Ball and Right Ball as

picture shown at the same time to
start the drone. Or click to
start the drone.

To fly up and down

Move the Left Ball up to fly the drone up
and move the Left Ball down to fly the
drone back down. The drone will stay
flying at a stable altitude.

17
 To rotate left and right
Move the Left Ball to the left to rotate the
drone to the left. Move the Left Ball to
the right to rotate the drone to the right.

Left Right

To fly right and left

Move the Right Ball to the left to fly the
drone to the left and move the ball to the
right to fly the drone to the right.

To fly forward and backward

Move the Right Ball up to fly the drone
forward and move the ball down to fly
the drone backwards.

Front Rear

18