32 | Rail Fixings by Lindapter ®
Type HD
This convenient fixing provides lateral
adjustability for fast and precise rail
alignment in low speed applications.
Type HD Soft Type HD Spring
Plug
GIRDER CLAMPS
Nose
Leg Skirt Elastomer Spring
Type HD Hard Type HD Isolated
RAIL FIXINGS
Nylon Insulator
(aka British Rail Orange)
LIFTING POINTS
• Suitable for all rails with tapered flanges and crane speeds up to 60m/min.
• Safely and easily secures rail using only hand tools.
Contact Lindapter for wheel loads above 400kN or lateral loads higher than wheel loads.
Please contact Lindapter to ensure suitability of component for application.
HOLLO-BOLT
Type HD Product Comparison
The table below shows the four options available. Each product has specific properties, e.g. a nylon insulator supplied with
the Type HD Isolated will allow the product to be electrically isolated from the rails. Contact Lindapter for more information.
Type HD Soft Type HD Hard Type HD Spring Type HD Isolated
Allows rail wave Clamps the rail down tightly Includes an elastomer spring Supplied with nylon insulator
Codes: HD20S / HD24S Codes: HD20H / HD24H Codes: HD20SP / HD24SP Codes: HD20SPOR / HD24SPOR
FLOOR FIXINGS
Precise lateral
adjustability 4 4 4 4
High strength
4 4 4 4
SUPPORT FIXINGS
SG Iron material
Various corrosion
protection options 4 4 4 4
High resistance
to lateral loads 4 4 4 4
Allows vertical rail /
rail wave movement 4 - 4* -
Electrically isolated
DECKING FIXINGS
from the rail - - - 4
Reduces track
running noise - - 4 -
Suitable for use
with a resilient pad 4 - 4 4
* The elastomer spring with a Shore A hardness of 90-97 provides some vertical restraint to the rail while still allowing it to lift with rail wave.
®
+44 (0) 1274 521444 www.Lindapter.com © Lindapter International 2021
Rail Fixings by Lindapter ® | 33
Type HD Technical Data
Type HD is suitable for all rails with tapered flanges and crane speeds
up to 60 metres per minute. Please contact Lindapter for wheel loads
above 400kN or lateral loads higher than wheel loads.
Pictured:
Lateral
GIRDER CLAMPS
Type HD
Spring Clip
Adjustability
The rotatable plug allows
+L
lateral adjustment (L)
-L
Z towards and away from
the rail. Before installing,
ensure the hexagon on
H
the plug is at the 3 o’clock
F V position (as shown). W
RAIL FIXINGS
X Y B
A
Material: SG iron, corrosion protection as requested.
Normal Lateral High Lateral Dimensions Distances 1) Width
LIFTING POINTS
Conditions Conditions
Clip Product Bolt SWL Tight. SWL Tight. Leg Stud Lateral Plate Y X W
Type Code 8.8 (FOS 4:1) Torque* (FOS 4:1) Torque* Length 3) Length 3) Adjust. Width
Z V H L min. A
kN Nm kN Nm mm mm mm mm mm mm mm
Soft HD20S M20 22.5 185 46.0 450 F-4 F + 40 +/- 11.5 B + 137 30 27 74
HD24S M24 40.0 320 60.0 760 F-4 F + 43 +/- 8 B + 130 30 27 74
HOLLO-BOLT
Hard HD20H 2) M20 22.5 185 46.0 450 F-8 F + 38 +/- 11.5 B + 137 30 27 74
HD24H 2) M24 40.0 320 60.0 760 F-8 F + 41 +/- 8 B + 130 30 27 74
Spring HD20SP M20 22.5 185 46.0 450 F-7 F + 40 +/- 11.5 B + 137 30 27 74
HD24SP M24 40.0 320 60.0 760 F-7 F + 43 +/- 8 B + 130 30 27 74
FLOOR FIXINGS
Isolated HD20SPOR M20 22.5 185 46.0 450 F-6 F + 42 +/- 11.5 B + 147 35 27 74
HD24SPOR M24 40.0 320 60.0 760 F-6 F + 45 +/- 8 B + 140 35 27 74
1) Based on plug set at 3 o’clock position.
2) Not suitable for use with a resilient pad.
3) Please specify the required leg length (V) when ordering. If you are using the resilient pad, increase the leg length and stud length (H) by the thickness of the pad.
* Torque figures based on bolts / setscrews in an unlubricated condition. For further information on lubricated fasteners see page 70. SUPPORT FIXINGS
How to install...
1) Position the HD clip on the bolt or stud, ensuring the
plug is at the 3 o’clock position, place a hexagon nut
and loosely tighten.
DECKING FIXINGS
2) Rotate the plug in a clockwise direction to locate the
clip against the rail. Laterally adjust the rail if required.
3) Tighten the hexagon nut to the recommended torque.
Watch the installation video at www.Lindapter.com
®
© Lindapter International 2021 www.Lindapter.com +44 (0) 1274 521444
