6-Port Antenna

698-960 | 698-960 | 1695-2690 MHz

5964300
5964300A 5964300G 5964300DG
3Xpol | 65° Az | 15.8 / 15.7 / 16.8 dBi | 0-10° / 0-10° / 0-10° | 1915 x 432 x 153 mm

• Tri band antenna, dual polarisation, 6 connectors

• Independent tilt on each band 0-10° / 0-10° / 0-10°
• Lightweight TwinLine platform and low windload
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0
• Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

ORDERING OPTIONS MODEL NUMBER

Manual Electrical Tilt Antenna 5964300

Remote Electrical Tilt Antenna AISG1.1 5964300A

Remote Electrical Tilt Antenna 3GPP/AISG2.0 with an MDCU RET Actuator 5964300G

Remote Electrical Tilt Antenna 3GPP/AISG2.0 with an MDDU RET Actuator 5964300DG

ACCESS PORT DESCRIPTION (CONNECTORS)

The antenna has 6 colour-coded connectors located at the bottom face.

Frequency Designation R1 R2 Y1

Frequency Range 698-960 MHz 698-960 MHz 1695-2690 MHz

Polarisation Xpol Xpol Xpol

Horizontal Beamwidth 70° 70° 65°

Electrical Downtilt Range 0-10° 0-10° 0-10°

(2x) 7/16-DIN (2x) 7/16-DIN (2x) 7/16-DIN

Connector Type
Female Long Neck Female Long Neck Female Long Neck

ELECTRICAL CHARACTERISTICS R1

698-960 MHz
Frequency Bands
698-806 MHz 790-862 MHz 824-894 MHz 880-960 MHz

Gain 14.7 dBi ± 0.6 dB 15.6 dBi ± 0.3 dB 15.7 dBi ± 0.4 dB 15.8 dBi ± 0.3 dB

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 74.4° ± 6.5° 71.1° ± 4.7° 72.2° ± 2.9° 70.9° ± 1.8°

Vertical Beamwidth (-3 dB) 11.7° ± 1.1° 10.3° ± 0.5° 10.1° ± 0.4° 9.6° ± 0.6°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 25 dB

Upper Sidelobe Rejection

> 15.5 dB > 17.3 dB > 16.8 dB >17.0 dB
(20° sector above main beam)

Front-to-Back Ratio
> 21.0 dB > 21.3 dB > 21.4 dB > 23.6 dB
@ 180° ±30°

Cross Polar Ratio - Main Direction > 16.1 dB > 17.0 dB > 16.7 dB > 16.6 dB

Maximum Power (Per Port) 250 W

Intermodulation
< -110 dBm
3rd Order for 2 x 20W Carriers
Values based on NGMN-P-BASTA version 9.6 requirements.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

REV110216A www.amphenol-antennas.com 1 of 5
 6-Port Antenna
698-960 | 698-960 | 1695-2690 MHz
5964300
5964300A 5964300G 5964300DG
3Xpol | 65° Az | 15.8 / 15.7 / 16.8 dBi | 0-10° / 0-10° / 0-10° | 1915 x 432 x 153 mm

ELECTRICAL CHARACTERISTICS R2

698-960 MHz
Frequency Bands
698-806 MHz 790-862 MHz 824-894 MHz 880-960 MHz

Gain 14.5 dBi ± 0.5 dB 15.2 dBi ± 0.4 dB 15.4 dBi ± 0.5 dB 15.7 dBi ± 0.4 dB

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 75.1° ± 5.5° 70.5° ± 3.6° 70.3° ± 2.6° 72.1° ± 2.2°

Vertical Beamwidth (-3 dB) 11.8° ± 1.0° 10.6° ± 0.5° 10.4° ± 0.6° 9.6° ± 0.6°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 25 dB

Upper Sidelobe Rejection
> 18.6 dB > 17.1 dB > 17.1 dB > 15.9 dB
(20° sector above main beam)
Front-to-Back Ratio
> 21.7 dB > 22.5 dB > 24.3 dB >25.1 dB
@ 180° ±30°
Cross Polar Ratio - Main Direction > 17.0 dB > 17.2 dB > 16.8 dB > 16.2 dB

Maximum Power (Per Port) 250 W

Intermodulation
< -110 dBm
3rd Order for 2 x 20W Carriers
Values based on NGMN-P-BASTA version 9.6 requirements.

ELECTRICAL CHARACTERISTICS Y1

1695-2690 MHz
Frequency Bands
1695-1880 MHz 1850-1990 MHz 1920-2180 MHz 2300-2500 MHz 2490-2690 MHz

Gain 16.4 dBi ± 0.4 dB 16.5 dBi ± 0.4 dB 16.7 dBi ± 0.4 dB 16.6 dBi ± 0.4 dB 16.8 dBi ± 0.4 dB

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 66.9° ± 4.1° 66.4° ± 3.8° 63.0° ± 4.4° 64.9° ± 3.6° 65.5° ± 4.2°

Vertical Beamwidth (-3 dB) 7.5° ± 0.6° 7.0° ± 0.4° 6.5° ± 0.6° 5.6° ± 0.1° 5.1° ± 0.4°

Electrical Downtilt Range 0-10°

Inter/Intra Band Isolation > 25 dB

Upper Sidelobe Rejection

> 16.6 dB > 16.9 dB > 16.9 dB > 16.8 dB > 16.5 dB
(20° sector above main beam)

Front-to-Back Ratio
> 23.4 dB >23.0 dB > 23.3 dB > 24.6 dB > 25.3 dB
@ 180° ±30°

Cross Polar Ratio - Main Direction > 14.6 dB > 14.6 dB > 15.1 dB > 14.9 dB > 14.9 dB

Maximum Power (Per Port) 200 W

Intermodulation
< -110 dBm
3rd Order for 2 x 20W Carriers

Values based on NGMN-P-BASTA version 9.6 requirements.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

REV110216A www.amphenol-antennas.com 2 of 5
 6-Port Antenna
698-960 | 698-960 | 1695-2690 MHz
5964300
5964300A 5964300G 5964300DG
3Xpol | 65° Az | 15.8 / 15.7 / 16.8 dBi | 0-10° / 0-10° / 0-10° | 1915 x 432 x 153 mm

ELECTRICAL DOWNTILT CONTROL

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the
Control corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite
rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted
Control
in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the
bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and
locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device
is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET
devices or for programming their configuration or for running a calibration process.

Multi-Device Control Unit The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas
(MCDU) with factory embedded motors. Refer to ordering options.
RET-Ready
Actuator
(one per antenna)
Multi-Device Dual Unit The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded
(MDDU) motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

REV110216A www.amphenol-antennas.com 3 of 5
 6-Port Antenna
698-960 | 698-960 | 1695-2690 MHz
5964300
5964300A 5964300G 5964300DG
3Xpol | 65° Az | 15.8 / 15.7 / 16.8 dBi | 0-10° / 0-10° / 0-10° | 1915 x 432 x 153 mm

ENVIRONMENTAL CHARACTERISTICS PACKAGING

Operating Temperature Range -40° C to +60° C

Carton Box
Environmental ETS 300 019 2.15 x 0.55 x 0.28 m
0.33 m3
RoHS Compliant Yes 38 kg
Includes 0900181/00 Kit
MECHANICAL CHARACTERISTICS

Dimensions (see drawing) Height: 1915 mm Width: 432 mm Depth: 153 mm

Weight 28 kg (excluding mounting accessory)

Shroud Outdoor fibreglass, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N

MOUNTING KIT OPTIONS PART NUMBER WEIGHT

All mounting bracket kits are ordered separately unless otherwise indicated.

Brackets for pole Ø48 to Ø115 mm (delivered as standard) 0900181/00 3.4 kg

Brackets for pole Ø70 to Ø150 mm (optional) 0900182/00 3.9 kg

Kit to add mechanical tilt (0°-10°) to above brackets (optional) 0900397/00 3.0 kg

Wall mounting brackets are available upon request.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

REV110216A www.amphenol-antennas.com 4 of 5
 6-Port Antenna
698-960 | 698-960 | 1695-2690 MHz
5964300
5964300A 5964300G 5964300DG
3Xpol | 65° Az | 15.8 / 15.7 / 16.8 dBi | 0-10° / 0-10° / 0-10° | 1915 x 432 x 153 mm

Bottom View of Antenna

Tilt indicators covered by transparent caps. Location of the MDCU

Manual adjustment is accessed by removing the caps. for RET Control
Knob colours are the same as the connectors.

Dimensions (in mm)

Installation

Always attach the antenna by the two mounting

points. Do not install the antenna with the
connectors facing upward.

In order to operate RET control, the transparent cap covering

the tilt adjustment indicator must be engaged and locked. Do
not cut it from the antenna.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

REV110216A www.amphenol-antennas.com 5 of 5