Scribd
Upload
236 views2 pages

Stiffener Ring Saddle Load Calculations

The document contains calculations to analyze stresses on a saddle ring stiffener for a shell with a radius of 1308 mm and thickness of 8 mm, under a load of 191269.1 N. It calculates the geometry and moments of inertia of 5 stiffener sections, then uses the results with material properties and stress concentration factors to evaluate equivalent stresses based on two analysis methods. Both methods find the calculated stresses are below the allowable limits.

Uploaded by

SAMER OSMAN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
236 views2 pages

Stiffener Ring Saddle Load Calculations

The document contains calculations to analyze stresses on a saddle ring stiffener for a shell with a radius of 1308 mm and thickness of 8 mm, under a load of 191269.1 N. It calculates the geometry and moments of inertia of 5 stiffener sections, then uses the results with material properties and stress concentration factors to evaluate equivalent stresses based on two analysis methods. Both methods find the calculated stresses are below the allowable limits.

Uploaded by

SAMER OSMAN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd

Stiffiner Ring on Saddle Calculations

Shell radius R = 1308 mm


Shell thickness ts = 8 mm
Stiffener stem thickness(tst1) = 10 mm
Stiffener height (d) = 250 mm
Stiffener cross length (b) = 150 mm
Stiffener cross thickness (tst2) = 10 mm
Load on saddle Q = 191269.1 N
Allowable Stress = 115 Mpa
Yield Stress = 248 MPa
K9 = 0.34
K10 = 0.053

Height d Area A Ig = bd3/12


Mark of area Length b (mm) Y (mm) A*Y (mm2) h (mm) h2 (mm2) A*h2 (mm4)
(mm) (mm2) (mm4)
1 10 258 2580 129 332820 4.6 21.53371 55556.981 14311260
2 74.7890819599 8 598.312656 4 2393.251 129.6 16806.64 10055628 3191.0008
3 74.7890819599 8 598.312656 4 2393.251 129.6 16806.64 10055628 3191.0008
4 70 10 700 253 177100 119.4 14246.7 9972693 5833.3333
5 70 10 700 253 177100 119.4 14246.7 9972693 5833.3333
Total 5176.62531 691806.5 40112199 14329309

A=SA = 5176.62531136 mm2


SAY = 691806.501245 mm3
C1=SAY/SA = 133.640443269 mm
C2 = 124.359556731 mm
SAh2 = 40112198.5224 mm4
SIg = 14329308.6683 mm4

I = SAH2+SIg= 54441507 mm4 = 5444.15 Cm4

y2
A3 A2

C1 h2
y1
X X
h1
y3 d
A1

C2 h3

A5 A4

According to Zic Analysis


S7 = -K9*Q / A + K10*Q*R*C1 / I
19.9863600215 Mpa <= 115 Mpa

Local stress in the shell is acceptable


S7 = -K9*Q / A - K10*Q*R*C2 / I

-42.8509959943 Mpa <= 124 Mpa

Local stress in the shell is acceptable


`
According to Compress software

ell Hoop Stress at test Sc = 149.8 Mpa

S7 = -K9*Q / A + K10*Q*R*C1 / I +Sc


169.786360021 Mpa <= 172.5 Mpa

Local stress in the shell is acceptable

S7 = -K9*Q / A - K10*Q*R*C2 / I

-42.8509959943 Mpa <= 172.5 Mpa

Local stress in the shell is acceptable

You might also like