Starting Formulation
SF 6004
Epoxy Glaze Coat for Seamless Flooring
EPON™ Resin 828 / HELOXY™ Modifier 8 / EPIKURE™ Curing Agent 3370
Introduction This low viscosity epoxy system has been designed as a sealer, glaze or finish coat for
seamless industrial flooring. It exhibits good physical strength properties and better
chemical resistance than aliphatic amine cured systems.
Formula Material Supplier Pounds Gallons
Resin Portion
EPON Resin 828 Hexion 92.0 9.58
HELOXY Modifier 8 Hexion 8.0 1.08
Total Resin Portion 100.0 10.66
Converter Portion
EPIKURE Curing Agent 3370 Hexion 37.0 4.43
Compounding Mix the resin and converter portions and blend to a homogeneous state with proper
agitationequipment. Avoid entrainment of excessive air into the blend with high speed
agitation but insure thorough mixing by agitating at low or moderate speeds for 3 to 5
minutes.
There is no induction time for this formulation. Due to its limited pot life, this system
should be applied immediately after mixing. The surface to be coated must be free of
dust, dirt, grease, or weakened concrete laltance. The surface temperature of the
substrate to be coated should be at a minimum of 23 °C. A uniform glaze, sealer, or finish
coating can be applied easily with a brush, paint roller, or squeegee.
Coverage rates depend on the application technique, substrate porosity, and intended
function. but for most applications an average thickness of 5 to 15 mils (320 to 110
square feet/gallon) is typical. Film weights at the low end of the range are for sealer
applications and higher film weights are for glaze and finish coat applications. Cure for
12 to 16 hours at normal room temperature before opening to light traffic; a 2 to 3 day
cure period should precede exposure to heavy traffic or corrosive chemicals.
Typical Handling Table 1 / Handling and Reactivity
Properties
Units Value
Resin/Converter Combining Ratio by weight 100 : 37
by volume 2.4 : 1
Blend Properties at 25 °C
Viscosity, Initial cP 1,050
Expected Pot Life, 100 gram mass min 30
Generated: April 17, 2022
Issue Date:
Revision:
® and ™ Licensed trademarks of Hexion Inc.
DISCLAIMER
The information provided herein was believed by Hexion Inc. (“Hexion”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Hexion are subject to Hexion’s terms and conditions of sale. HEXION MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY HEXION, except that the product shall conform to Hexion’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 1 of 3
Cured State Properties 1
Tensile Strength psi 10,350
Tensile Modulus 10 6 psi 0.47
Tensile Elongation % 4.2
Izod Impact, notch ft•lb/inch 0.49
Hardness Shore D 89
Heat Deflection Temperature °C 53
Tabor Abrasion, wear index 2 mg/cycle 49.8
Chemical Resistance 3
Immersion Units Water 5% Acetic Xylene
Acid
1 day % 0.09 0.23 0.08
1 week % 0.40 0.71 0.38
2 weeks % 0.59 0.96 0.46
3 weeks % 0.70 1.16 0.65
4 weeks % 0.83 1.36 0.80
1 System was cured for 7 days at 25 °C
2 Determlned by 1000 cycles with CS-1O wheels
3 Percent weight gain of 3 inch x l inch x 1/8 inch specimens Immersed at 25 °C
Storage Recommendations regarding storage conditions can be obtained by visiting our web site
at www.hexion.com
General Information
These are starting formulations and are not proven in the user’s particular application but are simply meant to demonstrate the efficacy of the
products and to assist in the development of the user’s own formulation. It is the user’s responsibility to fully-test and qualify the formulation,
along with the ingredients, methods, applications or equipment identified herein (“Information”), by the user’s knowledgeable formulator or
scientist, and to determine the appropriate use conditions and legal restrictions, prior to use of any Information.
Safety, Storage & Handling
Please refer to the MSDS for the most current Safety and Handling information.
Exposure to these materials should be minimized and avoided, if feasible, through the observance of proper precautions, use of appropriate
engineering controls and proper personal protective clothing and equipment, and adherence to proper handling procedures. None of these
materials should be used, stored, or transported until the handling precautions and recommendations as stated in the Material Safety Data Sheet
(MSDS) for these and all other products being used are understood by all persons who will work with them. Questions and requests for
information on Hexion Inc. ("Hexion") products should be directed to your Hexion sales representative, or the nearest Hexion sales office.
Information and MSDSs on non-Hexion products should be obtained from the respective manufacturer.
Contact Information
For product prices, availability, or order placement, please contact customer service:
www.hexion.com/Contacts/
Generated: April 17, 2022
Issue Date:
Revision:
® and ™ Licensed trademarks of Hexion Inc.
DISCLAIMER
The information provided herein was believed by Hexion Inc. (“Hexion”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Hexion are subject to Hexion’s terms and conditions of sale. HEXION MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY HEXION, except that the product shall conform to Hexion’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 2 of 3
For literature and technical assistance, visit our website at:www.hexion.com
Generated: April 17, 2022
Issue Date:
Revision:
® and ™ Licensed trademarks of Hexion Inc.
DISCLAIMER
The information provided herein was believed by Hexion Inc. (“Hexion”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Hexion are subject to Hexion’s terms and conditions of sale. HEXION MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY HEXION, except that the product shall conform to Hexion’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 3 of 3
