Module

9
Non conventional
Machining

Lesson
38

Version 2 ME, IIT Kharagpur

 Electro Chemical
Machining
Instructional Objectives
(i) Identify electro-chemical machining (ECM) as a particular type of
non-tradition processes
(ii) Describe the basic working principle of ECM process
(iii) Draw schematically the basics of ECM
(iv) Draw the tool potential drop
(v) Describe material removal mechanism in ECM
(vi) Identify the process parameters in ECM
(vii) Develop models for material removal rate in ECM
(viii) Analyse the dynamics of ECM process
(ix) Identify different modules of ECM equipment
(x) List four application of ECM
(xi) Draw schematics of four such ECM applications

1. Introduction
Electrochemical Machining (ECM) is a non-traditional machining (NTM) process
belonging to Electrochemical category. ECM is opposite of electrochemical or
galvanic coating or deposition process. Thus ECM can be thought of a controlled
anodic dissolution at atomic level of the work piece that is electrically conductive by a
shaped tool due to flow of high current at relatively low potential difference through an
electrolyte which is quite often water based neutral salt solution. Fig. 1 schematically
shows the basic principle of ECM.

In ECM, the workpiece is connected to the positive terminal of a low voltage high
WTWT
current DC generator or power source. The tool is shaped and shape of the tool is
OOOO
transferred to the workpiece. The tool is connected to the negative terminal.
Machining takes
place due to anodic dissolution at atomic level of the work material R O electrolyte
RO
K due to electrochemical reaction. A gap between the tool and the
workpiece is L K L required to be maintained to proceed with steady state machining.

Initial stage of Steady state of

ECM ECM

Version 2 ME, IIT Kharagpur

 Fig. 1 Schematic principle of Electro Chemical Machining (ECM)

2. Process
During ECM, there will be reactions occurring at the electrodes i.e. at the anode or
workpiece and at the cathode or the tool along with within the electrolyte.
Let us take an example of machining of low carbon steel which is primarily a ferrous
alloy mainly containing iron. For electrochemical machining of steel, generally a
neutral salt solution of sodium chloride (NaCl) is taken as the electrolyte. The
electrolyte and water undergoes ionic dissociation as shown below as potential
difference is applied
NaCl ↔ Na+ + Cl- H2O ↔ H+ +
(OH)As the potential difference is
applied between the work piece
(anode) and the tool (cathode), the
positive ions move towards the tool
and negative ions move towards the
workpiece.
Thus the hydrogen ions will take away electrons from the cathode (tool) and from
hydrogen gas as:
2H+ + 2e- = H2 ↑ at cathode
Similarly, the iron atoms will come out of the anode (work piece) as:
Fe = Fe+ + + 2e-
Within the electrolyte iron ions would combine with chloride ions to form iron
chloride and similarly sodium ions would combine with hydroxyl ions to form
sodium hydroxide
Na+ + OH- = NaOH
In practice FeCl2 and Fe(OH)2 would form and get precipitated in the form of
sludge. In this manner it can be noted that the work piece gets gradually
machined and gets precipitated as the sludge. Moreover there is not coating
on the tool, only hydrogen gas evolves at the tool or cathode. Fig. 2 depicts
the electro-chemical reactions schematically. As the material removal takes
place due to atomic level dissociation, the machined surface is of excellent
surface finish and stress free.

Version 2 ME, IIT Kharagpur

 ++ - + +
Fe OH − Cl H Na OH −
W T
O + ++ O
R Na OH − Fe H2 O
++
K Fe + L
OH − H
-
OH − Cl
e FeCl 2 e
Fe(OH) 2

Fig. 2 Schematic representation of electro-chemical reactions

The voltage is required to be applied for the electrochemical reaction to

proceed at a steady state. That voltage or potential difference is around 2 to
30 V. The applied potential difference, however, also overcomes the following
resistances or potential drops. They are:
• The electrode potential
• The activation over potential • Ohmic potential drop
• Concentration over potential
• Ohmic resistance of electrolyte
Fig. 3 shows the total potential drop in ECM cell.

Anode potential Voltage

Anodic Activation over potential

overvoltage ohmic potential
concentration potential
Voltage
concentration potential
Ohmic drop
activation overpotential cathodic overpotential
cathodic potential

anode cathode

Fig. 3 Total potential drop in ECM cell

3. Equipment
The electrochemical machining system has the following modules:
• Power supply
• Electrolyte filtration and delivery system

Version 2 ME, IIT Kharagpur

 • Tool feed system
• Working tank
Fig. 4 schematically shows an electrochemical drilling unit.

Pressure
Flow control
gauge
valve
Flow meter Constant feed to
Tool the tool
Pressure
relief valve -ve
PS Low voltage
+ ve high current
power supply

Pump
Spent electrolyte
O M centrifuge

P
sludge
Filters M O

Fig. 4 Schematic diagram of an electrochemical drilling unit

4. Modelling of material removal rate

Material removal rate (MRR) is an important characteristic to evaluate efficiency of a
non-traditional machining process.
In ECM, material removal takes place due to atomic dissolution of work material.
Electrochemical dissolution is governed by Faraday’s laws.
The first law states that the amount of electrochemical dissolution or deposition is
proportional to amount of charge passed through the electrochemical cell, which may
be expressed as: m Q∝ ,
where m = mass of material dissolved or deposited
Q = amount of charge passed
The second law states that the amount of material deposited or dissolved further
depends on Electrochemical Equivalence (ECE) of the material that is again the ratio
of the atomic weigh and valency. Thus t
A m ECEα α ν
QA
Thus mα ν
where F = Faraday’s constant
= 96500 coulombs

Version 2 ME, IIT Kharagpur

 ItA
∴m= Fν

m IA
∴ MRR = =
tρ ρνF
where I = current
ρ= density of the material
The engineering materials are quite often alloys rather than element consisting of
different elements in a given proportion.
Let us assume there are ‘n’ elements in an alloy. The atomic weights are given as A1,
A2, ………….., An with valency during electrochemical dissolution as ν1, ν2, …………, νn.
The weight percentages of different elements are α1, α2, ………….., αn (in decimal
fraction)
Now for passing a current of I for a time t, the mass of material dissolved for any
element ‘i’ is given by mi =Γaραi
where Γa is the total volume of alloy dissolved. Each element present in the alloy
takes a certain amount of charge to dissolve. Q Ai i

mi =
Fνi
νii
Fm
⇒ Qi =
Ai

FΓaρανii
⇒ Qi =
Ai
The total charge passed
QT = =It ∑Qi ∴
αν
QT = =It FΓρa ∑ ii
Ai
Now

MRR =Γa = 1 . I t
Fρ ανi i
∑
Ai

5. Dynamics of Electrochemical Machining

ECM can be undertaken without any feed to the tool or with a feed to the tool so that
a steady machining gap is maintained. Let us first analyse the dynamics with NO

Version 2 ME, IIT Kharagpur

FEED to the tool. Fig. 5 schematically shows the machining (ECM) with no feed to
the tool and an instantaneous gap between the tool and workpiece of ‘h’.

electrolyte

job tool

dh h

Fig. 5 Schematic representation of the ECM process with no feed to the tool

Now over a small time period ‘dt’ a current of I is passed through the electrolyte and
that leads to a electrochemical dissolution of the material of amount ‘dh’ over an area
of S
V V Vs
∴ I= = =
R rh
rh s

dh 1 A x ⎛ Vs.
1⎞⎟ then =. ⎜
dt F ρνx ⎝ rh s⎠
V
1 A x.
=.
F ρνx rh
for a given potential difference and alloy

dh = A x V . 1 = c dt
Fρνxr h h
where c = constant
A Vx

Version 2 ME, IIT Kharagpur

 =
Fρνxr
V c=
F rρ∑ανii
Ai
dhc
∴ = dt
h
hdh = cdt
At t = 0, h = h o and at t = t1 and h = h1
h1 t

∴ ∫ hdh = c dt∫
ho 0

∴ h12 − =ho2 2ct

That is the tool – workpiece gap under zero feed condition grows gradually following
a parabolic curve as shown in Fig. 6

ho

Fig. 6 Variation of tool-workpiece gap under zero feed condition

dh c
As = dt h
Thus dissolution would gradually decrease with increase in gap as the potential drop
across the electrolyte would increase
Now generally in ECM a feed (f) is given to the tool dh
c

Version 2 ME, IIT Kharagpur

 ∴ = − f dt h
Now if the feed rate is high as compared to rate of dissolution, then after sometime
the gap would diminish and may even lead to short circuiting. Under steady state
condition the gap is uniform i.e. the approach of the tool is compensated by
dissolution of the work material. Thus with respect to the tool, the workpiece is not
moving
dh c
Thus = =0
= f dt
h
c
∴f= h
or h* = steady state gap = c/f
Now under practical ECM condition it is not possible to set exactly the value of h* as
the initial gap. Thus it is required to be analysed if the initial gap value would have
any effect on progress of the process dh c
Now = − f dt h
h hf
Now h' = = h * c
ft f 2t
And t' = = h * c
dh' f / c dh 1 dh
. .
∴ dt' = f 2 / c dt = f dt dh c

Thus = − f dt h
dh' c cf
⇒ f = − =f − f dt' h'h * h'c

⇒ f dh' = f⎛⎜1− h' ⎞⎟ dt'

⎝ h' ⎠ dh'
1− h'
⇒ = dt' h'
h'
∴ dt' = dh'
1− h'
Now integrating between t’ = 0 to t’ = t’ when h’ changes from h o’ to h1’ t'
h1' h'

∴ ∫dt' = ∫ dh'
0 ho' 1−h'

h1' d1 h'(
∴ t' = ∫ − − ) + h∫1'd1 h'( − )
ho' (1−h') ho'

Version 2 ME, IIT Kharagpur

 t' = − +h'
h1' ln hh'o1'

−−11 o

now for different value of ho’, h1’ seems to approach 1 as shown in Fig. 7

Simulation for ho'= 0, 0.5, 1, 2,

3, 4, 5

h 1'
1
h 0= 0.5

h 0= 0

t'

Fig. 7 Variation in steady state gap with time for different initial gap

Thus irrespective of initial gap h

fh
h' ==1 ⇒
=1h* cc
∴h=
f
1
c A Vx .
or f==
h Fρνxr h

Version 2 ME, IIT Kharagpur

 Ax .V=Ax .i

∴f=
Fρνx rh Fρνx s A
I
x
. = MRR in mm /
s
∴f=
Fρνx s
Thus it seems from the above equation that ECM is self regulating as MRR is equal
to feed rate.

6. Applications
ECM technique removes material by atomic level dissolution of the same by
electrochemical action. Thus the material removal rate or machining is not dependent
on the mechanical or physical properties of the work material. It only depends on the
atomic weight and valency of the work material and the condition that it should be
electrically conductive. Thus ECM can machine any electrically conductive work
material irrespective of their hardness, strength or even thermal properties. Moreover
as ECM leads to atomic level dissolution, the surface finish is excellent with almost
stress free machined surface and without any thermal damage.
ECM is used for

• Die sinking
• Profiling and contouring
• Trepanning
• Grinding
• Drilling
• Micro-machining

Tool

Work

3D profiling
Die sinking

Fig. 8 Different applications of Electro Chemical Machining

Version 2 ME, IIT Kharagpur

 tool

work
drilling

(drilling)

tool

work

trepanning

Fig. 9 Drilling and Trepanning by ECM

Version 2 ME, IIT Kharagpur

7. Process Parameters
Power Supply
Type direct current
Voltage 2 to 35 V
Current 50 to 40,000 A
Current density 0.1 A/mm2 to 5 A/mm2
Electrolyte
Material NaCl and NaNO3
Temperature 20oC – 50oC
Flow rate 20 lpm per 100 A current
Pressure 0.5 to 20 bar
Dilution 100 g/l to 500 g/l
Working gap 0.1 mm to 2 mm
Overcut 0.2 mm to 3 mm
Feed rate 0.5 mm/min to 15 mm/min
Electrode material Copper, brass, bronze
Surface roughness, Ra 0.2 to 1.5 μm
Quiz Test
1. For ECM of steel which is used as the electrolyte
(a) kerosene
(b) NaCl
(c) Deionised water
(d) HNO3

2. MRR in ECM depends on

(a) Hardness of work material
(b) atomic weight of work material
(c) thermal conductivity of work material
(d) ductility of work material

3. ECM cannot be undertaken for

(a) steel
(b) Nickel based superalloy
(c) Al2O3
(d) Titanium alloy

4. Commercial ECM is carried out at a combination of

(a) low voltage high current
(b) low current low voltage
(c) high current high voltage
(d) low current low voltage

Problems

Version 2 ME, IIT Kharagpur

1. In electrochemical machining of pure iron a material removal rate of 600 mm 3/min
is required. Estimate current requirement.
2. Composition of a Nickel superalloy is as follows: Ni = 70.0%, Cr = 20.0%, Fe =
5.0% and rest Titanium
Calculate rate of dissolution if the area of the tool is 1500 mm 2 and a current of
2000 A is being passed through the cell. Assume dissolution to take place at lowest
valency of the elements.
ANi = 58.71 ρNi = 8.9 νNi = 2
ACr = 51.99 ρCr = 7.19 νCr = 2
AFe = 55.85 ρFe = 7.86 νFe = 2
ATi = 47.9 ρTi = 4.51 νTi = 3

3. In ECM operation of pure iron an equilibrium gap of 2 mm is to be kept.

Determine supply voltage, if the total overvoltage is 2.5 V. The resistivity of the
electrolyte is 50 Ω-mm and the set feed rate is 0.25 mm/min.
Answers
Answers to Quiz Test
1 – (b)
2 – (b) 3 – (c)
4 – (a)

Solution to Prob. 1

m AI
.

MRR = = =m
t Fν . m AI
∴ MRR =Γ= =
ρ ρνt F
MRR = 600 mm3/min = 600/60 mm3/s = 10 mm3/s = 10x10-3cc/s

∴ 10x10−3 = 56xI
96500x7.8x2
As AFe = 56 νFe = 2
F = 96500 coulomb
ρ = 7.8 gm/cc
96500x10x10−3 x7.8x2
∴I=
56
I = 268.8 A Answer

Solution of Problem 2

Now,
1

Version 2 ME, IIT Kharagpur

 = αNi αCr αFe αTi
+ + +
ρNi ρCr ρFe ρTi

8.07 gm/cc
m I
Now MRR = =
ρt Fρ∑ανi i
Ai
1000
=

96500x8.07x⎧⎨0.75x2 + 0.2x2 + 0.05x2 + 0.05x3⎫⎬

⎩ 58.71 51.99 55.85 47.9 ⎭
= 0.0356 cc/sec
= 2.14 cc/min
= 2140 mm3/min

MRR 2140
∴Rate of dissolution = = = 1.43 mm /min answer Area 1500
Solution to Prob. 3

c
h* =
f
VAFe
where c =
Fρ νFerFe

C=

−2.5)
h* = 2 = c = (V f

1347x 0.25
60

− 2.5
2= V
5.615
∴ V = 8.73 Volt. Answer

Version 2 ME, IIT Kharagpur