WB
orm
ef
ap
M
Form release-agent based on combination
of water and chemical active release agent
WHERE TO USE RECOMMENDATIONS
Anti-adhesive treatment of iron, aluminum, shutter • Do not dilute Mapeform WB with water.
wood, plywood and plastic forms (epoxy, phenolic, • Do not dilute Mapeform WB with solvents or other oils.
polyester and polyurethane resins). It is particularly • Do not use Mapeform WB with concrete, gypsum
suitable for vertical applications. and polystyrene forms.
• When using with rubber forms make sample tests or
Some application examples contact the MAPEI Technical Services Department.
• To facilitate form release of precast concrete. Its
particular viscosity makes it suitable for vertical HOW TO USE
applications on formworks where it is important to Mapeform WB is ready-to-use.
limit product pouring when sprayed.
• To facilitate form release of steam-cured concrete. APPLICATION
• To form release concrete cast in plastic forms. All substrate must be clean, dry and dust free.
• To form release concrete cast in metal forms. Mapeform WB can be applied by brush, sponge,
squeegee or light horticultural sprayers.
TECHNICAL CHARACTERISTICS Mapeform WB must be applied in very thin coating and
Mapeform WB is an environmental friendly mould any excess must be removed.
release agent based on the combination of water and Contact the MAPEI Technical Services Department for
chemically active release agent. further information.
The efficiency of Mapeform WB is given by its action of CLEANING
chemical concrete stripping from formwork. Tools used for applying Mapeform WB can be cleaned
with water.
Mapeform WB features the following advantages:
• it is water based, safe and clean; CONSUMPTION
• excellent concrete finish is achieved that exhibits a Spray Applied: 30-40 m²/litre.
smooth, hard, uniform finish; Marine Ply and Steel faced form work: upto 70 m²/litre.
• Mapeform WB has no negative effect on concrete
properties; STORAGE
• Mapeform WB does impair the adhesion of Mapeform WB can be stored for 12 months in sealed
subsequent surface treatments when applied at the containers away from prolonged, direct exposure to
recommended coverage rates. sunlight and at a temperature between +5°C and +35°C.
WB
form TECHNICAL DATA (typical values)
ape
M
PRODUCT IDENTITY
(GB) A.G. BETA
Consistency: fluid liquid
Colour: milky white
Density (g/cm³): 0.95 - 1.05 at +23°C
Brookfield viscosity at +23°C - N1 Sp 50 : 9 cPs
Release action: chemical
APPLICATION DATA
Preparation: ready-to-use
Application: suitable pressure pump > 6 bar
Any reproduction of texts, photos and illustrations published
PACKAGING specification. The installer should ensure that
The product is supplied in 200 l drums and our latest product data and safety information
here is prohibited and subject to prosecution
25 kg tanks. sheets have been consulted prior to use.
SAFETY INSTRUCTIONS FOR Please refer to the current version of the
PREPARATION AND APPLICATION Technical Data Sheet, available from our
Mapeform WB is not considered as a website www.mapei.com
hazardous according to the current
regulation regarding the classification of LEGAL NOTICE
mixtures. It is however recommended to use The contents of this Technical Data Sheet
gloves, eye protection and to take the usual (“TDS”) may be copied into other project-
precaution for the handling of chemical related documents, but the resulting
products. document shall not supplement or replace
requirements per the TDS in force at the
For further and complete information about time of the MAPEI product installation.
the safe use of our product please refer to our The most up-to-date TDS can be down-
latest version of the Safety Data Sheet. loaded from our website www.mapei.com.
IMPORTANT NOTES ANY ALTERATIONS TO THE WORDING
Whilst we try to ensure that any advice, OR REQUIREMENTS CONTAINED OR
recommendations or information given in our DERIVED FROM THIS TDS EXCLUDES THE
literature is accurate and correct, we have no RESPONSIBILITY OF MAPEI.
control over the circumstances in which our
product is used. It is therefore important that
7826-4-2019 (UAE)
installers satisfy themselves that the product All relevant references
and conditions are suitable for the envisaged for the product are available
application. No warranty can be given or upon request and from
responsibility accepted other than, that the www.mapei.com
product supplied by us will meet our written
BUILDING THE FUTURE
