DOBLE F6150sv TECHNICAL SPECIFICATIONS

The F6150sv line of Power System Simulators is designed for simulation tests on relay and protection schemes.

VOLTAGE SOURCES (6 TOTAL) VOLTAGE SOURCES OUTPUT VOLTAGE

Source Configuration Power

6-phase AC (L-N) 6 x 150 V @ 75 VA

3-phase AC (L-N) 3 x 300 V @ 150 VA

1-phase AC (LL-LN) 1 x 600 V @ 300 VA

DC (LL-LN) 3 x 424 V @ 150 W

Available Range 75 V, 150 V, 300 V

CONVERTIBLE V/I SOURCES
CONVERTIBLE V/I SOURCES OUTPUT CURRENT
Source Configuration Power

6-phase AC (L-N) 6 x 1.5 A @ 97.5 VA**

6 x 1 A @ 75 VA***
3-phase AC (L-N) 3 x 3 A @ 195 VA**
3 x 2 A @ 150 VA***
1-phase AC (LL-LN) 1 x 9 A @ 585 VA**
1 x 6 A @ 450 VA***
DC (LL-LN) 1 x 6.36 A @ 585 W**
1 x 4.24 A @ 450 W***
Available Range 0.5 A, 1 A, 1.5 A, 3 A, 9 A

CURRENT SOURCES
CURRENT SOURCES OUTPUT CURRENT
Source Configuration Power

6-phase AC (L-N) 6 x 35 A @ 131.25 VA* 275

6 x 17.5 A @ 87.5 VA*** 250

225

3-phase AC (L-N) 3 x 70 A @ 262.5 VA* 200

3 x 35 A @ 175 VA***
175
Power (VA)

1-phase AC (LL-LN) 1 x 210 A @ 787.5 VA* 150

1 x 105 A @ 625 VA*** 125

DC (LL-LN) 1 x 140 A @ 787.5W* 100

Compliance Voltage @ 30a (Transient Mode)
1 x 70 A @ 625W*** 75 @35a Range = 7.5 volts
50 @70a Range = 3.75 volts
Available Range 0.5 A, 1 A, 1.5 A, 3 A, 9 A 25

0
0 10 20 30 40 50 60 70
Amps (A)

LOW LEVEL SOURCES

Voltage
Range Current Power Transient Mode
Power
All values are shown with F6005 option:
Convertible
Amplifier 6.7 VRMS 4.5 VRMS 6.7 VRMS *Long Duration - 45 seconds
Sources **Short Duration - 1.5 seconds
***Continuous
3.399 VRMS 6.798 VRMS
Current
(Non-Enhanced) (Non-Enhanced)
Amplifier N/A
3.5 VRMS 7 VRMS
Sources
(Enhanced) (Enhanced)

Number 12

Accuracy ± 0.25% of reading

Resolution 331 μV/bit

www.doble.com
DOBLE F6150sv TECHNICAL SPECIFICATIONS
LOGIC INPUTS (VOLTAGE OR CONTACT SENSE) ANALOG INPUT MEASUREMENT AIM
8 external Analog or Digital
Description Isolated Inputs Paired Inputs Recording
Signals

Inputs 2 (First Strike) 3 Pairs (6) Internal Source recording 12 Sources

250 V RMS AC / 300 V 250 V RMS AC / 300 V Ranges 250 mV, 2.5 V, 25 V, 250 V RMS
Voltage Sense
DC DC
Bandwidth DC, 0-5kHz
Open Circuit Test
12 V DC 4 V DC Input Impedance 150 kΩ
Voltage
Max Input Voltage 250 V RMS AC / 300 V DC
Short Circuit Test
20 mA DC >50 mA DC
Current Isolation ±500 V peak channel to channel

0.1 msec max pickup 0.1 msec max pickup Accuracy

Response Time
/dropout /dropout
Typical ±0.06%
Input Impedance 150 kΩ 150 kΩ Maximum ±0.15%

VARIABLE OUTPUT BATTERY SIMULATOR

Isolation ±500 V peak ±500 V peak
Range 6 - 300 V DC
LOGIC OUTPUTS Resolution 0.3 V
FET Power 90 W, 1.5 A max
Description (High Speed Relay
Electronic) 50/60 Hz Ripple <0.2% of Range
Number 4 4 Accuracy <±5%
Isolation Voltage ±500 V peak ±500 V peak TIMING ACCURACY
0.1 ms pick up / <10 ms pick up /
Response Time With F6895 (Antenna and
dropout dropout ± 50 ns
Receiver)
(Breaking cap AC:
2000 VA with Vmax + 6 ms (un-modulated)
With F6051 (Irig-b Converter)
Maximum (Make/ 250 V, Imax 8 A) +9 ms (modulated)
0.5 A
Break Current) (Breaking cap DC:
50 W with Vmax 300 With F6053 PTP (1588)
200 ns
V, Imax 8 A) Power and Power Utility Pole

Input Voltage 250 V RMS 250 V RMS POWER CONSUMPTION

F6150e/sv at Full Power 2600 W
METERING FUNCTIONS
DC Meter Inputs F6150e/sv at Idle 140 W

Input Range 0 - ±10 V DC / 0 - ±20 mA DC

Typical <0.003%

Guaranteed <0.05%

AC Sources

Typical <0.02% of metering loads

Logic Input As Counters

Frequency 10 kHz

Pulse width >175 µs

DOBLE F6150sv TECHNICAL SPECIFICATIONS
AC AMPLITUDE ACCURACY @ 50-60 HZ @ 20° - 30° C GENERAL SPECIFICATIONS
0.02% of reading High-impact, molded, flame-retardant ABS-
Typical
+ .01% of range Enclosure meets National Safe Transit Association testing
specification No.1A for immunity to severe shock
0.09% of reading and vibration
Guaranteed
+ .04% of range
IEC 60068-2-27 Shock (15g/11ms, half sine)
Playback Rate for Transient Test 10 kHz Mechanical IEC 60068-2-6 Vibration (10-150 Hz, 20m/s2)
IEC 60068-2-6 Drop Test
CONVERTIBLE SOURCE IN CURRENT MODE
@ 20° - 30° C Weight 42lb,19.05kg (front cover and strap included)
Guaranteed <0.5% 15 X 9.5 X 18 in
Dimensions
38 X 24 X 45.7 cm
TIMERS AND TRIGGERS
Calibration Certification traceable to N.I.S.T. standards
Timers Number 8
IEC 60068-2-2 Dry Heat (+85°C storage; + 50°C
Max Recording Time <24 h Rating Operating), IEC 60068-2-1 Cold (-50°C
Environmental storage; 0°C operating), IEC 60068-2-30 Damp
±0.0005% Heat (+55°C, 6 cycles, 95% humidity), NEMA
Accuracy
of reading, ±50 µs Enclose Rating Type 1IEC Enclosure IP20
Resolution 100 µs FCC 47 CFR Part 15 Class A (USA),
EMC Emissions EN55011:1998/A1:1999/A2:2002 Group 1 Class
FREQUENCY
A ISM(EU), AS/NZS CISPR 11:2004 Class A ISM
Bandwidth DC - 3 kHz at Full Power (Australia), ICES-001 Issue 3 ISM (Canada)

DC, 0.1 Hz - 2.0 kHz EMC Immunity EN 61000-6-2:2005; IEC 61000-4-2/3/4/5/6/11

Range
Continuous Full Load
Quality Assurance
Resolution 0.001 Hz Management Third Party certification to ISO 9001:2000
System
PHASE ANGLE @ 50/60 HZ
Humidity Up to 95% relative humidity, non-condensing
Range ±360° - 0°
IEC 801-2 I.E.C. performance level 1 @ 10kV:
Accuracy ± 0.25° Electrostatic normal performance within specifications.
Discharge Immunity I.E.C. performance level 2 @ 20kV: no permanent
Resolution ± 0.1° damage
DISTORTION @ 50 /60HZ V & I SOURCES TOTAL ANSI/IEEE c37.90. The simulator functions as a
HARMONIC DISTORTION (THD) source during surge withstand capability tests,
Surge Withstand
Capability when the ANSI/IEEE specified isolating circuit is
Typical <0.02% interposed between the simulator and the test
Guaranteed <0.1% relay
Line Power Supply 105-264 V, 47-63 Hz
Accuracy
Safety* EN 61010-1 third edition; UL 61010-1
Typical 0.5 ppm

@ 20° - 30° C 1.5 ppm Communication Ethernet or USB control to PC, Wi-Fi
Interfaces (802.11 B+G bands, 30 - 80ft, 9 - 24m)
@ 0° - 50° C 10 ppm
IEC 61850
IEC 61850 first edition parts [6, 7-2, 8-1 and 9-2]
GOOSE Second edition parts [6, 7-1, 7-2, 7-3, 7-4, 8-1,
*All instruments are designed to meet CSA and UL requirements. and 9-2]
Sampled Value messages per 9-2LE guide line
Sample Values
(3 streams) and IEC 61869-9 (4 streams)

Doble Engineering Company Specifications are subject to change without notice.

Worldwide Headquarters Doble is an ISO 9001 & ISO/IEC 17025 & 17034 Certified
123 Felton Street, Marlborough, MA 01752 USA Company.
tel +1 617 926 4900 | fax +1 617 926 0528 Doble is an ESCO Technologies Company.
www.doble.com PUBLISHED: APRIL 2021