Bench Vice Assembly 1

Bench Vice Assembly

In this project, you will create the Bench Vice assembly. Figures B through E shows the views
and dimensions of the components of the Bench Vice assembly.

Figure 1 The Bench Vice assembly

Figure 2 Views and dimensions of the base

CAMD_ProE_Assembly 1 MIT College of Engineering, Pune - 411038.

 2 Student Project

Figure 3 Views and dimensions of the Vice Jaw

Figure 4 Views and dimensions of various components of the Bench Vice assembly
CAMD_ProE_Assembly 2 MIT College of Engineering, Pune - 411038.
 Bench Vice Assembly 3

Figures 5 Views and dimensions of various components of the Bench Vice assembly

CAMD_ProE_Assembly 3 MIT College of Engineering, Pune - 411038.

 Butterfly Valve Assembly 1

Butterfly Valve Assembly

Create the components of the Butterfly Valve assembly and then assemble them, as shown in
Figure 1. The dimensions of the components are shown in Figures 2 through 7. Assume the
missing dimensions.

Figure 1 The Butterfly Valve assembly

Figure 2 Dimensions of the Body

CAMD_ProE_Assembly 4 MIT College of Engineering, Pune - 411038.
2 Student Project

Figure 3 Dimensions of the Shaft Figure 4 Dimensions of the Retainer

Figure 5 Top view of the Arm Figure 6 Sectional front view of the Arm

Figure 7 Dimensions of the Plate, Nut, and Screw

CAMD_ProE_Assembly 5 MIT College of Engineering, Pune - 411038.

 V-Block Assembly 1

V-Block Assembly
Create all the components of the V-Block assembly and then assemble them, as shown in
Figure 1. The dimensions of the components are shown in Figures 2 and 2.

Figure 1 The V-Block assembly

Figure 2 Views and dimensions of the V-Block body

CAMD_ProE_Assembly 6 MIT College of Engineering, Pune - 411038.
2 Student Project

Figure 3 Views and dimensions of the U-Clamp and Fastener

CAMD_ProE_Assembly 7 MIT College of Engineering, Pune - 411038.

 Crosshead Assembly 1

Crosshead Assembly
In this project, you will create all components of the Crosshead assembly and then assemble
them, as shown in Figure 1. Also you will create an exploded state, shown in Figure 2. The
dimensions of the components are shown in Figures 3 through 7.

Figure 1 The Crosshead assembly

Figure 2 The exploded state of Crosshead assembly

CAMD_ProE_Assembly 8 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Front view and the right-side view of the Body

Figure 4 Dimensions of Keep Plate Figure 5 Dimensions of Piston Rod

Figure 6 Dimensions of the Brasses and Bolt

CAMD_ProE_Assembly 9 MIT College of Engineering, Pune - 411038.
 Crosshead Assembly 3

Figure 7 Dimensions of Nut

CAMD_ProE_Assembly 10 MIT College of Engineering, Pune - 411038.

 Double Bearing Assembly 1

Double Bearing Assembly

In this project, you will create the Double Bearing assembly shown in Figure 1. The exploded
state of the assembly is shown in Figure 2 and the dimensions of the components of the
Double Bearing assembly are shown in Figures 3 through 7.

Figure 1 The completed Double Bearing Figure 2 The exploded view of the Double
assembly Bearing assembly

Figure 3 Top view of the Base Figure 4 Top view of the Cap

Figure 5 Front view of the Base Figure 6 Front view of the Cap
CAMD_ProE_Assembly 11 MIT College of Engineering, Pune - 411038.
2 Student Project

Figure 7 Dimensions and drawing views of the Bushing and the Bolt

CAMD_ProE_Assembly 12 MIT College of Engineering, Pune - 411038.

 Fixture Assembly 1

Fixture Assembly
Create all the components of the Fixture assembly and then assemble them, as shown in
Figure 1. The details of the components of the Fixture assembly are shown in
Figures 2 through 5.

Figure 1 The Fixture assembly

Figure 2 Dimensions of the End Plate

CAMD_ProE_Assembly 13 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Dimensions of the Disk

Figure 4 Dimensions of the Support Pin and the Bolt

CAMD_ProE_Assembly 14 MIT College of Engineering, Pune - 411038.

 Fixture Assembly 3

Figure 5 Dimensions of the Spacer, Center Pin, and the Nut

CAMD_ProE_Assembly 15 MIT College of Engineering, Pune - 411038.

 Plummer Block Assembly 1

Plummer Block Assembly

In this project, you will create the components of the Plummer Block assembly, as shown in
Figure 1 and then assemble them. The dimensions of the components are given in Figures 2
through 4.

Figure 1 The Plummer Block assembly

Figure 2 Views and dimensions of the Casting

CAMD_ProE_Assembly 16 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Views and dimensions of the Cap

Figure 4 Views and dimensions of Brasses, Nut, Lock Nut, and Bolt

CAMD_ProE_Assembly 17 MIT College of Engineering, Pune - 411038.

 Press Tool Assembly 1

Press Tool Assembly

In this project, you will create the Press Tool assembly shown in Figure 1. The exploded state
of the assembly is shown in Figure 2 and the dimensions of the components of the Press Tool
assembly are shown in Figures 2 through 5.

Figure 1 The completed Press Tool assembly after assembling the

Top Plate with the assembly

Figure 2 The exploded view of the Press Tool as- Figure 3 Figure showing the Bottom Plate
sembly

CAMD_ProE_Assembly 18 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 4 Dimensions and views of the Top Figure 5 Dimensions and views of the Guide Pillar
Plate and Guide Bush

CAMD_ProE_Assembly 19 MIT College of Engineering, Pune - 411038.

 Pulley Support Assembly 1

Pulley Support Assembly

Create the components of the Pulley Support assembly and then assemble them, as shown in
Figure 1. After creating the assembly, create its exploded view, as shown in Figure 2. The
dimensions of the components are given in Figures 4 through 8.

Figure 1 The Pulley Support assembly

Figure 2 Exploded view of the Pulley Support assembly

CAMD_ProE_Assembly 20 MIT College of Engineering, Pune - 411038.
2 Student Project

Figure 4 Dimensions of the Pulley Figure 5 Dimensions of the Bushing

Figure 6 Left-side view of the Bracket Figure 7 Sectioned front view of the

Figure 8 Dimensions of the Washer, Cap Screw, Turn Screw, and Nut

CAMD_ProE_Assembly 21 MIT College of Engineering, Pune - 411038.

 Pulley Support Assembly 3

Figure 3 Parts list for the Pulley Support assembly

CAMD_ProE_Assembly 22 MIT College of Engineering, Pune - 411038.

 Shock Assembly 1

Shock Assembly
In this project, you will create all components of the Shock assembly and then assemble
them, as shown in Figure 1. Also create an exploded state of the assembly, as shown in
Figure 2. The dimensions of the components are shown in Figures 3 through 10.

Figure 1 The Shock assembly

Figure 2 The exploded state of the Shock Assembly

CAMD_ProE_Assembly 23 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Dimensions for Bracket Figure 4 Dimensions for Pivot

Figure 5 Dimensions for U-Support

CAMD_ProE_Assembly 24 MIT College of Engineering, Pune - 411038.

 Shock Assembly 3

Figure 6 Dimensions for Bushing Figure 7 Dimensions for Self-locking nut

Figure 8 Dimensions for Washer Figure 9 Dimensions for Hexagonal bolt

Figure 10 Dimensions for Castle nut

CAMD_ProE_Assembly 25 MIT College of Engineering, Pune - 411038.

 Wheel Support Assembly 1

Wheel Support Assembly

Create all the components of the Wheel Support assembly and then assemble them, as shown
in Figure 1. The dimensions of the components are shown in Figures 2 through 6.

Figure 1 The Wheel Support assembly

Figure 2 Dimensions of the Base Figure 9-3 Dimensions of the Support

Figure 4 Front view of the Wheel Figure 5 Sectioned side view of the Wheel

CAMD_ProE_Assembly 26 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 6 Dimensions of the Shoulder Screw, Bolt, Nut, Bushing,

and Washer

CAMD_ProE_Assembly 27 MIT College of Engineering, Pune - 411038.

 Pipe Vice Assembly 1

Pipe Vice Assembly

In this Project, you will create all components of the Pipe Vice assembly, as shown in
Figure 1, and then assemble them. The dimensions of the components are given in
Figures 2 and 3.

Figure 1 The Pipe Vice assembly

Figure 2 Views and dimensions of the Base

CAMD_ProE_Assembly 28 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Views and dimensions of the Screw, Handle, Movable Jaw, and Handle Screw

CAMD_ProE_Assembly 29 MIT College of Engineering, Pune - 411038.

 Shaper Tool Head Assembly 1

Shaper Tool Head Assembly

Create the Shaper Tool Head assembly, as shown in Figure 1. After creating the assembly, create
its exploded view, as shown in Figure 2. The dimensions of the components are given in
Figures 3 through 7.

Figure 1 The Shaper Tool Head assembly

Figure 2 The exploded view of the Shaper Tool

Head assembly

CAMD_ProE_Assembly 30 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Views and dimensions of the Swivel Plate

CAMD_ProE_Assembly 31 MIT College of Engineering, Pune - 411038.

 Shaper Tool Head Assembly 3

Figure 4 Views and dimensions of the Back Plate

CAMD_ProE_Assembly 32 MIT College of Engineering, Pune - 411038.

4 Student Project

Figure 5 Views and dimensions of the Vertical Slide

CAMD_ProE_Assembly 33 MIT College of Engineering, Pune - 411038.

 Shaper Tool Head Assembly 5

Figure 6 Views and dimensions of various components

CAMD_ProE_Assembly 34 MIT College of Engineering, Pune - 411038.

 Stock Bracket Assembly 1

Stock Bracket Assembly

In this project, you will create the Stock Bracket assembly shown in Figure 1. The details of
the components of the Stock Bracket assembly are shown in Figures 2 through 8.

Figure 1 The Stock Bracket assembly

Figure 2 Top and front views of the Stock Support Base

CAMD_ProE_Assembly 35 MIT College of Engineering, Pune - 411038.
2 Student Project

Figure 3 Front and right-side views of the Stock Figure 4 Top and front views of the Adjusting Screw
Support Roller Nut

Figure 5 Front and right-side views of the Support Roller Bracket

Figure 6 Views of the Adjusting Nut Handle and

Adjusting Screw Guide

CAMD_ProE_Assembly 36 MIT College of Engineering, Pune - 411038.

 Stock Bracket Assembly 3

Figure 7 Views of the Support Adjusting Screw Figure 8 Top and front views of the Thrust
Bearing

CAMD_ProE_Assembly 37 MIT College of Engineering, Pune - 411038.

 Motor Blower Assembly 1

Motor Blower Assembly

In this project, you will create the Motor Blower assembly shown in Figure 1. The exploded
view of the assembly is shown in Figure 2. The details of the components of the Motor Blower
assembly are shown in Figures 3 through 8.

Figure 1 Motor Blower assembly

Figure 2 Exploded view of the Motor Blower assembly

CAMD_ProE_Assembly 38 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 3 Dimensions of the Upper Housing

Figure 4 Dimensions of the Lower Housing

CAMD_ProE_Assembly 39 MIT College of Engineering, Pune - 411038.
 Motor Blower Assembly 3

Figure 5 Dimensions of the Blower

Figure 6 Dimensions of the Motor

CAMD_ProE_Assembly 40 MIT College of Engineering, Pune - 411038.

4 Student Project

Figure 7 Dimensions of the Cover

Figure 8 Dimensions of the Shaft

CAMD_ProE_Assembly 41 MIT College of Engineering, Pune - 411038.

 Radial Engine Assembly 1

Radial Engine Assembly

In this project, you will create the Radial Engine assembly shown in Figures 1 and 2. The
Radial Engine assembly will be created in two parts, one will be the subassembly and the
other will be the main assembly. The dimensions of the components of the Radial Engine
assembly are shown in Figures 3 through 6.

Figure 1 The Radial Engine assembly Figure 2 The exploded view of the assembly

Figure 3 Views and dimensions of the Piston

CAMD_ProE_Assembly 42 MIT College of Engineering, Pune - 411038.

2 Student Project

Figure 4 Views and dimensions of the Articulated Rod

Figure 5 Views and dimensions of the Master Rod

CAMD_ProE_Assembly 43 MIT College of Engineering, Pune - 411038.

 Radial Engine Assembly 3

Figure 6 Views and dimensions of the Rod Bush Upper, Rod Bush Lower, Piston Pin Plug,
Piston Pin, Piston Rings, and Master Rod Bearing

CAMD_ProE_Assembly 44 MIT College of Engineering, Pune - 411038.