Serenity Series Surface Mounted Panel Wall System

General Specifications
The Serenity Series Surface Mounted Panel Wall System
shall be manufactured by Amico Corporation, in
accordance with job specific shop drawings and
documents. The following is a general specification, and
components listed may not be present or required in
final product.

The Serenity Series Surface Mounted Panel Wall System

is listed by Underwriters Laboratories Inc. (UL) in Canada
and the United States of America. Amico Corporation
manufactures all products in accordance with the CSA
Z7396.1-06 standard, National Fire Protection Association
(NFPA), NFPA-99c (current edition), National Electric Code
(NEC), and the Canadian Electrical Code (CEC).

The Panel Wall is Made Up of

Several Components:
• Vertical sections where the services are located.
These components have optional vertical and/or
horizontal rails systems and reveals as well as 3D Submittals and Verifications
wrap finished front panels attached. These sections
are installed on the finished wall. Job specific shop drawings shall be produced for each
project. These shop drawings will clearly indicate the area
• Central section with removable 3D wrap panels of medical gas termination and electrical connection
for bed area. This component is located between points inside the panel wall system. Built drawings will be
the vertical sections. This section is installed on the produced and e-mailed at the time of shipment.
finished wall and has optional horizontal/vertical
aluminum reveals or rails. It can accommodate bed Amico Corporation will manufacture equipment as per
bumpers and decorative resin panels with built-in signed approval drawings and verifications documents
LED lights. Please refer to approved submittal which are provided in the job specific submittal package.
drawings for project specific details.
Each vertical section has integrated electrical raceways
• Decorative side vertical sections with removable 3D and conduit, providing single point connection for all
wrap panels. These components are located to the electrical power type (critical, normal and low voltage/
left or right of the vertical sections, are installed on communication).
the finish wall and have optional horizontal/vertical
aluminum reveals or rails. Please refer to approved All medical gas piping shall be hard-piped (no flexible gas
submittal drawings for project specific details. hose) and brazed to a single point of connection.

• Cabinets for IT stations, patient lift station or glove

storage components. These components are
made of MDF with a 3D wrap finish. Please refer to
approved submittal drawings for project specific
details.
• Decorative wood valance. Can be installed on the
front or top of the panel wall. Can accommodate
LED lights. Please refer to approved submittal
drawings for project specific details.
Serenity Series Surface Mounted Panel Wall System
Materials and Construction Grounding and Bonding
All ground conductors shall be installed in conduit or
raceway. Each power receptacle shall have a ground
Integrated Accessory Rails (Optional) conductor connected to a grounding screw. Where electrical
Numbers of integrated rails (horizontal and vertical) are to terminations are located inside the Serenity Series Panel Wall, a
match final shop drawings. Accessory rails are clear etched grounding bus will be installed for each type of power, and shall
anodized aluminum. be installed as to insure grounding for the complete power
system.
Fascia
3/8" MDF with 3D wrap finish (typical). All fascia panels Low Voltage Data Provisions
shall be removable for access and easy installation or This shall be connected to a device junction box via conduit
maintenance of panel wall services using the spring clip or raceway. Amico Corporation shall include a pull cord
system. extending from junction box to service provision. Telephone
nurse call patient station device shall be furnished, installed
Medical Gas Outlets and wired by low voltage contractor.
Amico Corporation, DISS or quick connection type, console
style. Electrical Receptacles
This shall be Hospital Grade 15 or 20 amp, 120 or 277 volt,
Medical Gas Manifold UL listed and marked hospital grade. Amico Corporation shall
Medical gas distribution shall be supplied by pipe drops furnish and install receptacles with wiring required, as shown
to the single point connection above the unit as indicated on submittal shop drawings. Electrical contractor shall insure
on the drawing. All medical gas outlets and piping shall compatibility of plug on accessory equipment to be used
be brazed and tested in accordance with CSA Z7396.1-06 with these devices:
standard and NFPA-99c. All medical gas piping shall be
Type L copper pipe. Each outlet, piping and manifold shall Duplex receptacles shall be NEMA style 5-15R or 5-20R, in
pass a 24 hour standing pressure test. ivory color for use on normal power circuits, and in red color
for use on critical branch power circuits.
Electrical Wiring
Wire for standard and critical branch power circuits shall be Warranty
#10 or #12 (as specified) type THHN stranded copper wire, Amico Corporation warrants its Architectural Products to be
600 volt, with heat resistant thermoplastic insulation for free from material defects and workmanship for a period of
hot (black) and neutral (white). Grounds shall be #10 THHN ten (10) years from the date of shipment.
stranded copper wire (green). All ground conductors shall
be installed in conduit.

Distributed By:

Amico Corporation 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada | 600 Prime Place, Hauppauge, NY 11788, USA
Toll Free Tel: 1.877.462.6426 | Toll Free Fax: 1.866.440.4986 | Tel: 905.764.0800 | Fax: 905.764.0862
www.amico.com ACA-SP-SERENITY-SURFACE 07.24.2020