o
AutoForm-
Aut
FormingSolver
m
Software for Simulation of Stamping Processes
r
oFo
Aut
rm
oFo
►
rm
Simulation of line and progressive die
stamping as well as hemming processes
Rapid and accurate simulation of deep drawing,
Aut
oFo
►
restriking, trimming and flanging operations
► Accurate springback simulation
www.autoform.com
► Deep insight into all operations of the stamping
process
► Rapid verification of multiple new concepts for
quality and cost improvements
Aut
o
AutoForm-FormingSolver
Features & Benefits
Aut
Rapid and Accurate Simulation of the Entire Stamping Process
The simulation of stamping processes by AutoForm-FormingSolver combined with the results evaluation by AutoForm-
m
Explorer provide the user with all the necessary information to design the process. AutoForm-FormingSolver simulates
line and progressive die stamping as well as hemming processes.
Line die stamping
Drawing: All relevant parameters for the drawing operation
are set up by AutoForm-Explorer. These parameters include
r
single or double action presses, number of tools, drawbeads
and spacers, constant or time-variable binder pressure, lancing
oFo
cuts, regular or tailor-welded blanks, etc. AutoForm-
FormingSolver simulates the drawing operation and provides all
the necessary results for its further evaluation.
Trimming: Engineers can easily define all trimming operations,
including contour trims and hole cutting. To realistically reflect
the actual process, different cam directions can be specified for
each trim or cut line. The simulation of the trimming operation
is carried out by AutoForm-FormingSolver. Progressive die stamping
Springback: Updated material model, fine-tuning of the Hemming
existing shell element, advanced contact handling and
Aut
AutoForm-FormingSolver simulates both roll and table top
rm
optimized mesh refinement are some of the latest technological hemming. The simulation of hemming processes can be carried
achievements combined in AutoForm-FormingSolver to ensure out in the early stages of product development and production
the successful calculation of springback problems. Springback planning when the die layout of the drawing and forming
can be calculated after each forming or cutting operation and operations is still not available. The CAD geometry of the
the clamping order can also be taken into consideration. flanged part provides the main input for simulation by
AutoForm-FormingSolver. In addition, the simulation can be
carried out in process engineering when the detailed definition
of the drawing and forming operations is available.
oFo
Progressive die stamping
The simulation of progressive die stamping significantly differs
rm
from that of line die stamping. Due to the complexity of
progressive dies, it is important to address all the factors that
contribute to achieving the desired level of part quality,
including blank position, pilots, blank boundary and
stretch-web deformation. Other factors to be considered are
timing and interaction of carriers, pads, and upper and lower
Line die stamping tools. AutoForm-FormingSolver simulates progressive die
stamping and the results obtained are then evaluated by
Aut
AutoForm-Explorer.
oFo
Switzerland Pfäffikon SZ +41 43 444 61 61
Germany Dortmund +49 231 9742 320
The Netherlands LB Capelle aan den IJssel +31 180 668 255
www.autoform.com
France Aix-en-Provence +33 4 42 90 42 60
Spain Barcelona +34 93 320 84 22
Italy Turin +39 011 620 41 11
Czech Republic Praha +420 603 248 580
Sweden Stockholm +31 180 668 255
United States Troy, MI +1 888 428 8636
Aut
Mexico Corregidora, Qro. +52 442 225 1104
Brazil São Bernardo do Campo +55 11 4122 6777
India Hyderabad +91 40 4068 9999
China Shanghai +86 21 5386 1153
Japan Tokyo +81 3 6459 0881
Korea Seoul +82 2 2113 0770
© 2020 AutoForm Engineering GmbH, Switzerland.
"AutoForm" and other trademarks listed under www.autoform.com or trade names contained in this documentation or the Software
are trademarks or registered trademarks of AutoForm Engineering GmbH. Third party trademarks, trade names, product names and
logos may be the trademarks or registered trademarks of their respective owners. AutoForm Engineering GmbH owns and practices
various patents and patent applications that are listed on its website www.autoform.com. Software and specifications may be subject
to change without notice.
Publication FS-3-E
