Nära® Hospital Bassinet

Maintenance Manual

4402

EN

4402-009-002 Rev AA.1 2020/12

Symbols

Consult instructions for use

General warning

Caution

Catalogue number

 Serial number

Quantity

UNIT Unit number

 For US Patents see www.stryker.com/patents

Manufacturer

Safe working load

Do not place infant / newborn on this surface

4402-009-002 Rev AA.1 EN

Table of Contents
Warning/Caution/Note Definition ..............................................................................................................................2
Summary of safety precautions ................................................................................................................................2
Pinch points............................................................................................................................................................2
Introduction ...............................................................................................................................................................3
Product description .................................................................................................................................................3
Intended use ..........................................................................................................................................................3
Expected device life ................................................................................................................................................3
Contraindications ....................................................................................................................................................3
Specifications .........................................................................................................................................................3
Product illustration ..................................................................................................................................................5
Contact information .................................................................................................................................................5
Serial number location.............................................................................................................................................6
Unit number............................................................................................................................................................6
Date of manufacture................................................................................................................................................7
Setup .....................................................................................................................................................................7
Preventive maintenance ...........................................................................................................................................8
Service ......................................................................................................................................................................9
Cradle top cover removal/replacement .....................................................................................................................9
Cradle bottom cover replacement...........................................................................................................................10
Push bar replacement ...........................................................................................................................................13
Caster replacement...............................................................................................................................................16
Drawer slide replacement ......................................................................................................................................17
Gas cylinder replacement ......................................................................................................................................18
Base cover replacement ........................................................................................................................................21
Top level assembly - 4402-100-001 .......................................................................................................................23
Bassinet assembly - 4402-010-001 ........................................................................................................................24
Base assembly - 4402-001-001..............................................................................................................................26
International top level assembly - 4402-100-002 ...................................................................................................29
International bassinet assembly - 4402-010-009 ...................................................................................................30
International base assembly - 4402-001-007 .........................................................................................................32
Cabinet-drawer assembly - 4402-050-001 .............................................................................................................35
Drawer assembly - 4402-050-002 ..........................................................................................................................36
Document holder assembly - 4402-050-007 ..........................................................................................................37
Cradle assembly - 4402-010-002 ...........................................................................................................................38

4402-009-002 Rev AA.1 1 EN

Warning/Caution/Note Definition
The words W A R N I N G , C A U T I O N , and N O T E carry special meanings and should be carefully reviewed.

WARNING

Alerts the reader about a situation which, if not avoided, could result in death or serious injury. It may also describe
potential serious adverse reactions and safety hazards.

CAUTION
Alerts the reader of a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to the
user or patient or damage to the product or other property. This includes special care necessary for the safe and effective
use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse.

N o t e - Provides special information to make maintenance easier or important instructions clearer.

Summary of safety precautions

Always read and strictly follow the warnings and cautions listed on this page. Service only by qualified personnel.

CAUTION
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.

Pinch points

EN 2 4402-009-002 Rev AA.1

Introduction
This manual assists you with the operation or maintenance of your Stryker product. Read this manual before operating or
maintaining this product. Set methods and procedures to educate and train your staff on the safe operation or maintenance
of this product.

CAUTION
• Improper usage of the product can cause injury to the patient or operator. Operate the product only as described in this
manual.
• Do not modify the product or any components of the product. Modifying the product can cause unpredictable operation
resulting in injury to patient or operator. Modifying the product also voids its warranty.

Note
• This manual is a permanent part of the product and should remain with the product even if the product is sold.
• Stryker continually seeks advancements in product design and quality. This manual contains the most current product
information available at the time of printing. There may be minor discrepancies between your product and this manual. If
you have any questions, contact Stryker Customer Service or Technical Support at 1-800-327-0770.

Product description
The Stryker model 4402 N ä r a ® Hospital Bassinet consists of a base cabinet, two- way drawers, retractable work surface,
five inch soft-wheel casters, a clear basket, and mattress. The basket allows for easy access to the infant / newborn patient,
tilts, and latches securely onto the base cabinet.

Intended use
The N ä r a Hospital Bassinet is a sleeping surface for infant / newborn patients from birth to five months of age. The product
has a tilting basket to allow visibility of the patient by hospital staff and family members. The top surface of the device raises
and lowers to allow easier access to the infant / newborn. The product can come in contact with healthy skin.
This product is for use with infant / newborn patients as a sleeping surface.

The bassinet is for use in infant / newborn clinical care settings; such as:
• Labor and delivery units
• Neonatal intensive care units
• Other patient care rooms
This product is not intended for patients that can crawl or reposition themselves independently.

Expected device life

The N ä r a Hospital Bassinet has a five year expected service life under normal use conditions and with appropriate periodic
maintenance.

Contraindications
None known.

Specifications

4402-000-001

4402-009-002 Rev AA.1 3 EN

 4402-000-002

Safe working load

Mattress 12 lb (5.4 kg)

Basket 12 lb (5.4 kg)

Each drawer 5 lb (2.3 kg)

Retractable work space 5 lb (2.3 kg)

Chart holder 5 lb (2.3 kg)

Description Length Width Height

Bassinet base 33 in. (83.8 cm) 21 in. (53.3 cm) n/a

Basket 26.5 in. (67.3 cm) 12.5 in. (31.7 cm) 7.5 in. (19.0 cm)

Two-way drawer (each) 19.25 in. (48.8 cm) 13.75 in. ( 34.9 cm) 6.25 in. (15.8 cm)

Retractable work space 11.5 in. (29.2 cm) 10 in. (25.4 cm) n/a

Chart holder 10 in. (25.4 cm) 2.75 in. (6.9 cm) 13.5 in. (34.2 cm)

Mattress 26 in. (66.04 cm) 12 in. (30.48 cm) 1.5 in. (3.81 cm)

Mattress material Polyester fiber 100% all new material

Adjustable height 30.5 in. to 39.5 in. (77.4 to 100 cm)

Environmental conditions Operation Storage and transportation

Ambient temperature 104° F 140° F
(40° C) (60° C)
50° F 14° F
(10° C) (-10° C)

Relative humidity (non-condensing) 75 % 85 %

30 % 20 %

Atmospheric pressure 1016 hPa 1060 hPa

700 hPa 500 hPa

Stryker reserves the right to change specifications without notice.

EN 4 4402-009-002 Rev AA.1

Product illustration

B G

C
D H

E
I

J
K

A Basket G Transport handle

B Mattress H Retractable work surface

C Reposition handle I Narrow base cabinet

D Height adjustment bar, both sides J Steer lock, green

E Chart holder K Caster locks, red

F Two-way drawers L 5” dual soft-wheel casters

Contact information
Contact Stryker Customer Service or Technical Support at: 1-800-327-0770.

Stryker Medical
3800 E. Centre Avenue
Portage, MI 49002
USA

To view your operations or maintenance manual online, see https://techweb.stryker.com/.

Have the serial number (A) of your Stryker product available when calling Stryker Customer Service or Technical Support.
Include the serial number in all written communication.

4402-009-002 Rev AA.1 5 EN

Serial number location
You can find the serial number inside the cabinet (A), opposite the chart holder (Figure 1).

Figure 1 – Serial number location

Unit number
Have the unit number of your basket (A) or mattress (B) available when calling Stryker Customer Service or Technical
Support. Include the unit number in all written communication.

EN 6 4402-009-002 Rev AA.1

Date of manufacture
The year of manufacture is the first four digits of the serial number.

Setup
During setup, unpack the cartons and check all items for proper operation. Make sure that the product is working properly
before it is put into service.
Remove all shipping and packaging materials from the product prior to use.

4402-009-002 Rev AA.1 7 EN

Preventive maintenance
Remove product from service before you perform the preventive maintenance inspection. Check all items listed during
annual preventive maintenance for all Stryker Medical products. You may need to perform preventive maintenance checks
more often based on your level of product usage. Service only by qualified personnel.
Inspect the following items:

All fasteners are secure

Chart holder for damage
All four casters swivel
All four casters are free of wax and debris
All mechanisms operate
Two basket retention pins and tilt bar retainer are intact and secure
Retractable work surface is intact and secure
Basket tilt bar is intact
Drawers are intact and slide
Push handles
Height adjustment bars
Bassinet raises and lowers
Mattress for rips, tears, punctures, wear
Base cabinet for cracks or damage
Labels for legibility, proper adherence, and integrity

Product serial number:

Completed by:

Date:

EN 8 4402-009-002 Rev AA.1

Service
Cradle top cover removal/replacement
Tools required:
• 3/16” Hex wrench
• 3/8” Nut driver
Procedure:
1. Apply the brakes.
2. Remove the basket from the product.
3. Using a 3/16” hex wrench, remove the two yellow basket pivot pins (W and Y) (Figure 2) from the top cover. Save the
pivot pins.

Figure 2 – Cradle top

4. Access the nuts (AB) (Figure 3) that secure the basket trend catch (AA) to the top cover. Open the top and bottom
drawer and look through the cutout directly underneath the trend catch (AA).

4402-009-002 Rev AA.1 9 EN

 Figure 3 – Basket trend catch

5. Using a 3/8” nut driver, remove the two nuts (AB) that secure the trend catch (AA). Save the nuts.
6. Grasp both sides of the top cover cradle (U) and pull up until the bottom and the top cover V e l c r o ® separate.
7. Remove and discard the cradle top cover.
8. Reverse to install.
N o t e - Once the top cover is in place, firmly press on the top cover to secure the V e l c r o ®.
9. Verify proper operation before you return the product to service.

Cradle bottom cover replacement

Tools required:

• 1/8” Hex wrench

• 5/32” Hex wrench
• T15 Torx driver
• Rubber hammer
Procedure:
1. Apply the brakes.
2. Remove cradle top cover. See Cradle top cover removal/replacement (page 9).

EN 10 4402-009-002 Rev AA.1

3. Using a 1/8” hex wrench, remove the eight screws (F and G) that secure the column and drawer assembly to the top
cradle bracket (Figure 4).

Figure 4 – Column and drawer assembly

N o t e - Lower the unit to the lowest height to help minimize the column dropping.
4. Using a T15 Torx driver, remove the four screws that secure both columns to each valance bracket.
N o t e - The entire column and drawer assembly should now rest on top of the base cover.
5. Using a 1/8” hex wrench, remove the two screws (AL) (Figure 5) that secure each release handle to the top cradle
bracket. Save the handle and screws.

4402-009-002 Rev AA.1 11 EN

 Figure 5 – Release handle

6. Using 5/32” hex wrench, remove the four screws (E) and washers (D) (Figure 6) from each cylinder bracket that secure
the cylinder to the top cradle bracket. Save the screws and washers.

EN 12 4402-009-002 Rev AA.1

 Figure 6 – Cylinder bracket

N o t e - Add loctite blue threadlocker to a minimum of three threads on item L.

7. Using a rubber hammer, strike the top cradle bracket, near the cylinder to disengage the bracket from the cylinder top.
Repeat on opposite side.
8. Using a workbench or table, flip the top assembly upside down.
9. Using a T15 Torx driver remove the six screws (AP) and washers (AN) that secure the two valance brackets. Save the
screws and washers.
10. Working from one side of the assembly, firmly pull up on the cradle bottom cover.
11. Remove and discard the cradle bottom cover.
12. Reverse to install.
13. Verify proper operation before you return the product to service.

Push bar replacement

Tools required:
• 1/8” Hex wrench
• T15 Torx driver
• 1/2” Speed ratchet
• Loctite blue threadlocker

Procedure:
1. Apply the brakes.
2. Remove the cradle top cover. See Cradle top cover removal/replacement (page 9).

4402-009-002 Rev AA.1 13 EN

3. Using a 1/8” hex wrench, remove the eight screws (F and G) (Figure 7) that secure the column and drawer assembly to
the top cradle bracket. Save the screws.

Figure 7 – Column and drawer assembly

N o t e - Lower the unit to the lowest height to help minimize the column dropping.
4. Using a T15 Torx driver, remove the four screws that secure both columns to each valance bracket. Save the screws.
N o t e - The entire column and drawer assembly should now rest on top of the base cover.

EN 14 4402-009-002 Rev AA.1

5. Using a T15 Torx driver, remove the six screws (AP) and washers (AN) (Figure 8) that secure two valance brackets.
Save the screws and washers.

Figure 8 – Valance brackets

6. Using a 1/2” speed ratchet remove the four screws (L) and washers (K) (Figure 9) that secure the push bar to the cradle
bracket. Save the screws and washers.

4402-009-002 Rev AA.1 15 EN

 Figure 9 – Push bar

Note
• Carefully pull down on the corner of the cradle bottom cover to gain access to the screws.
• During reinstall, add loctite blue threadlocker to a minimum of three threads on item L.
7. Remove and discard the push bar.

N o t e - Remove and save the two rubber sleeves from the push bar.
8. Reverse to install.
9. Verify proper operation before you return the product to service.

Caster replacement
Tools required:
• 5/16” Hex driver
• 3/8” Drive ratchet
• Jack
• Torque wrench
Procedure:
1. Apply the brakes.
2. Use a small jack, near the caster to be replaced.

EN 16 4402-009-002 Rev AA.1

3. Using a 3/8” drive ratchet and 5/16” hex driver, remove the bolt (N) and caster (K, L, M) (Figure 10) assembly from the
base weldment. Discard the caster assembly.

Torque item N
to 35 to 45 ft-lb

Torque item N
Torque item N to 35 to 45 ft-lb
to 35 to 45 ft-lb
Torque item N
to 35 to 45 ft-lb

Figure 10 – Base weldment

4. Reverse to install.
5. Verify proper operation before you return the product to service.

Drawer slide replacement

Tools required:
• T15 Torx driver
• T10 Torx driver
• 5/16” Wrench
Procedure:
1. Apply the brakes.
2. Pull open the drawer.
3. Using a T10 Torx driver and 5/16” wrench, remove the two screws that secures the drawer slide to the drawer. Save the
screws.
4. Using a T15 Torx driver, remove the screw (E) and washer (F) (Figure 11) that secure the drawer slide to the column.
Save the screw and washer.

4402-009-002 Rev AA.1 17 EN

 Figure 11 – Drawer slide and columns

5. Open the same drawer from the opposite side and repeat step 4.
6. From the open drawer, pull the drawer slide tab out of the drawer.
7. Open the same drawer from the opposite side and repeat step 6.
8. Remove and discard the entire drawer slide assembly.
9. Reverse to install.
10. Verify proper operation before you return the product to service.

Gas cylinder replacement

Tools required:

• 1/8” Hex wrench

• 3/16” Hex wrench
• 5/32” Hex wrench
• T15 Torx driver
• Rubber hammer
• Needle nose pliers

Procedure:
1. Using a 1/8” hex wrench, remove the eight screws (F and G) (Figure 12) that secure the column and drawer assembly to
the top cradle bracket.

EN 18 4402-009-002 Rev AA.1

 Figure 12 – Column and drawer assembly

N o t e - Lower the unit to the lowest height to help minimize the column dropping.
2. Using a T15 Torx driver, remove the four screws (E) and washers (D) (Figure 13) that secure both columns to each
valance bracket. Save the screws and washers.
N o t e - The entire column and drawer assembly should now rest on top of the base cover.
3. Using 5/32” hex wrench, remove the eight screws (D) and washers (C) that secure the cylinder bracket to the top cradle
bracket for the gas cylinder. Remove both sides. Save the screws and washers.

4402-009-002 Rev AA.1 19 EN

 Figure 13 – Top cradle bracket

N o t e - Add loctite blue threadlocker to a minimum of three threads on item L.

4. Using a rubber hammer, strike the top cradle bracket, near the gas cylinder to remove the cradle bracket from the gas
cylinder.
5. Remove the cradle assembly and supports to gain access to the gas cylinder. Set aside the cradle assembly.
6. Lift up and remove the cabinet/drawer assembly. Set aside the cabinet/drawer assembly.
7. Using a 5/32” hex wrench, remove the two screws that secure the column support bracket. Save the screws.
8. Using a 3/16: hex wrench, remove the screw (AJ) and spacer (AH) from the lower guide tube (Figure 14). Save the
screw and spacer.

Figure 14 – Column support bracket

9. Using the needle nose pliers, remove the gas cylinder clip. Save the clip.
10. Grab the shaft of the gas cylinder and pull up to remove the gas cylinder from the base support bracket. Save the
washers (D), bumpers (C) and clip (F) for reinstall (Figure 15). Discard the gas cylinder.

EN 20 4402-009-002 Rev AA.1

 Figure 15 – Gas cylinder shaft

11. Reverse to install.

12. Verify proper operation before you return the product to service.

Base cover replacement

Tools required:

• Small jack
• 5/32 Hex t-handle
Procedure:
1. Apply the brakes.
2. Using a small jack, at one end of the product, raise the product a few inches off the floor.
N o t e - You can push the product up against a wall for added precaution.
3. Using a 5/32” hex t-handle, remove the two screws (W) and two washers (G) that secure the column to the base
weldment. Save the screws and washers (Figure 16).

4402-009-002 Rev AA.1 21 EN

 Torque item N
to 35 - 45 ft-lb

Torque item N
Torque item N to 35 - 45 ft-lb
to 35 - 45 ft-lb
Torque item N
to 35 - 45 ft-lb

Figure 16 – Base weldment

4. Repeat step 1 and step 2 on the opposite end of the product.

5. Remove the jack.
6. With the help of a second person, grasp both pull handles and raise the entire column assembly off of the base
assembly.
N o t e - Use one foot to firmly step on top of the base cover while you pull up on the assembly.
7. Set assembly securely out of the way.
8. Remove and discard the base cover (U).
9. Reverse to install.
10. Verify proper operation before you return the product to service.

EN 22 4402-009-002 Rev AA.1

Top level assembly - 4402-100-001
Rev C (Reference only)

Item Number Name Quantity

A 4402-010-001 Bassinet assembly - 4402-010-001 1
(page 24)
B 4402-010-003 Basket assembly 1
C 4402-031-001 Mattress assembly 1
D 4402-010-921 Warning label, USA only 1

4402-009-002 Rev AA.1 23 EN

Bassinet assembly - 4402-010-001
Rev AA (Reference only)

EN 24 4402-009-002 Rev AA.1

Item Number Name Quantity

A 4402-001-001 Base assembly - 4402-001-001 (page 1

26)

B 4402-010-002 Cradle assembly - 4402-010-002 1

(page 38)

C 0012-131-000 Lock washer 8

D 0002-121-000 Button head cap screw 8

E 4402-050-001 Cabinet-drawer assembly - 4402-050- 1

001 (page 35)

F 0013-055-000 Internal tooth lock washer 8

G 0004-913-000 Button head cap screw 8

H 0011-641-000 Washer 4
J 0002-123-000 Button head cap screw 4

K 4402-050-118 Magnet 8

L 4402-010-917 N ä r a logo label 2

M 4402-010-918 Stryker logo label 3

N 4402-010-914 Load / no baby label 5

P 4402-010-912 Domestic specification label 1

R 4402-010-906 Date of manufacture label 2

4402-009-002 Rev AA.1 25 EN

Base assembly - 4402-001-001
Rev F (Reference only)

Torque item N
to 35 - 45 ft-lb

Torque item N
Torque item N to 35 - 45 ft-lb
to 35 - 45 ft-lb
Torque item N
to 35 - 45 ft-lb

EN 26 4402-009-002 Rev AA.1

 Torque item AJ
to 25±3 in-lb

N o t e - Add loctite blue threadlocker to a minimum of 3 threads on item AJ.

Item Number Name Quantity

A 4402-001-101 Base 1
B 4402-001-003 Lower guide tube assembly 2

C 4402-002-107 Washer 2
D 4402-002-108 Gas cylinder bumper 6

E 4402-002-111 Gas spring 2

F 4402-002-109 Cylinder gas clip 2

G 0012-131-000 Lock washer 16

H 0002-118-000 Button head cap screw 8

J 0026-679-000 Dowel pin 2

K 4402-001-106 5” swivel, brake, directional caster 1

L 4402-001-104 5” swivel caster 2
M 4402-001-107 5” swivel, brake caster 1
N 0002-119-000 Button head cap screw 4

P 0011-639-000 Washer 2
R 3001-200-052 Grounding chain 1

T 0025-653-000 Domed blind rivet 1

4402-009-002 Rev AA.1 27 EN

Item Number Name Quantity

U 4402-001-002 Base cover assembly 1

V 4402-001-111 Finished inner extrusion 1

W 0002-125-000 Button head cap screw 2

Y 4402-001-126 Extrusion bushing mount plate 8

AA 4402-001-004 Upper guide tube assembly 2

AB 3150-002-405 Lower bushing 2

AC 3150-002-410 Upper bushing 2

AD 0002-117-000 Button head cap screw 2

AE 4402-001-132 Lift stop 4

AF 4402-001-134 Rubber bumper 2

AG 0001-214-000 Flat head machine screw 2

AH 4402-001-133 Spacer 2

AJ 0004-901-000 Socket head cap screw 2

AK 4402-010-906 Label, date of manufacture 1

AL 4402-010-912 Label, domestic specification 1

EN 28 4402-009-002 Rev AA.1

International top level assembly - 4402-100-002
Rev AA (Reference only)

Item Number Name Quantity

A 4402-010-009 International bassinet assembly - 4402- 1
010-009 (page 30)
B 4402-010-003 Basket assembly 1
C 4402-031-004 Mattress assembly 1

4402-009-002 Rev AA.1 29 EN

International bassinet assembly - 4402-010-009
Rev AA (Reference only)

EN 30 4402-009-002 Rev AA.1

Item Number Name Quantity

A 4402-001-007 International base assembly - 4402- 1

001-007 (page 32)
B 4402-010-002 Cradle assembly - 4402-010-002 1
(page 38)

C 0012-131-000 Lock washer 8

D 0002-121-000 Button head cap screw 8

E 4402-050-001 Cabinet-drawer assembly - 4402-050- 1

001 (page 35)

F 0013-055-000 Internal tooth lock washer 8

G 0004-913-000 Button head cap screw 8

H 0011-641-000 Washer 4
J 0002-123-000 Button head cap screw 4

K 4402-050-118 Magnet 8

L 4402-010-917 N ä r a logo label 2

M 4402-010-918 Stryker logo label 3

N 4402-010-914 Load/no baby label 5

P 4402-010-919 International specification label 1

R 4402-010-922 Date of manufacture label 2

4402-009-002 Rev AA.1 31 EN

International base assembly - 4402-001-007
Rev AA (Reference only)

Torque item N
to 35 - 45 ft-lb

Torque item N
Torque item N to 35 - 45 ft-lb
to 35 - 45 ft-lb
Torque item N
to 35 - 45 ft-lb

EN 32 4402-009-002 Rev AA.1

 Torque item AJ
to 25±3 in-lb

N o t e - Add loctite blue threadlocker to a minimum of 3 threads on item AJ.

Item Number Name Quantity

A 4402-001-101 Base 1
B 4402-001-003 Lower guide tube assembly 2

C 4402-002-107 Washer 2
D 4402-002-108 Gas cylinder bumper 6

E 4402-002-111 Gas spring 2

F 4402-002-109 Cylinder gas clip 2

G 0012-131-000 Lock washer 16

H 0002-118-000 Button head cap screw 8

J 0026-679-000 Dowel pin 2

K 4402-001-106 5” swivel, brake, directional caster 1

L 4402-001-104 5” swivel caster 2
M 4402-001-107 5” swivel, brake caster 1
N 0002-119-000 Button head cap screw 4

P 0011-639-000 Washer 2
R 3001-200-052 Grounding chain 1

T 0025-653-000 Domed blind rivet 1

4402-009-002 Rev AA.1 33 EN

Item Number Name Quantity

U 4402-001-002 Base cover assembly 1

V 4402-001-111 Finished inner extrusion 2

W 0002-125-000 Button head cap screw 2

Y 4402-001-126 Extrusion bushing mount plate 8

AA 4402-001-004 Upper guide tube assembly 2

AB 3150-002-405 Lower bushing 2

AC 3150-002-410 Upper bushing 2

AD 0002-117-000 Button head cap screw 2

AE 4402-001-132 Lift stop 4

AF 4402-001-134 Rubber bumper 2

AG 0001-214-000 Flat head machine screw 2

AH 4402-001-133 Spacer 2

AJ 0004-901-000 Socket head cap screw 2

AK 4402-010-919 Label, date of manufacture 1

AL 4402-010-922 Label, domestic specification 1

EN 34 4402-009-002 Rev AA.1

Cabinet-drawer assembly - 4402-050-001
Rev C (Reference only)

Item Number Name Quantity

A 4402-050-003 Document holder column assembly 1

B 4402-050-004 Column assembly 1

C 4402-050-002 Drawer assembly - 4402-050-002 2

(page 36)

D 0013-054-000 Internal tooth lock washer 8

E 0004-299-000 Button head cap screw 8

F 0017-032-000 Acorn nut 8

G 4402-050-127 Document holder spacer 4

H 4402-050-007 Document holder assembly - 4402- 1

050-007 (page 37)
J 0012-131-000 Lock washer 4
K 0002-120-000 Button head cap screw 4

4402-009-002 Rev AA.1 35 EN

Drawer assembly - 4402-050-002
Rev A (Reference only)

Item Number Name Quantity

A 4402-050-101 Drawer body 1

B 4402-050-005 Drawer face assembly 2

C 0013-054-000 Internal tooth lock washer 10

D 0004-299-000 Button head cap screw 8

E 4402-050-117 Magnet cup 2

F 0001-213-000 Flat head machine screw 2

G 0017-032-000 Acorn nut 2

EN 36 4402-009-002 Rev AA.1

Document holder assembly - 4402-050-007
Rev E (Reference only)

Item Number Name Quantity

A 4402-050-124 Document holder body 1

B 4402-050-126 Document holder wire form 1

4402-009-002 Rev AA.1 37 EN

Cradle assembly - 4402-010-002
Rev E (Reference only)

EN 38 4402-009-002 Rev AA.1

4402-009-002 Rev AA.1 39 EN
N o t e - Add loctite blue threadlocker to a minimum of three threads on item L.

Item Number Name Quantity

A 4402-010-004 Cradle internal frame assembly 1

B 0056-042-000 Rubber bumper 8

C 4402-010-108 Machined gas cylinder top 2

D 0012-131-000 Lock washer 8

E 0002-121-000 Button head cap screw 8

F 4402-010-124 Bumper bar 1

G 4402-010-126 Push bar 1

H 4402-010-137 Grommet, bumper / push bar, left 2

J 4402-010-127 Grommet, bumper / push bar, right 2

K 4402-010-161 Saddle washer 8

L 0003-401-000 Hex head cap screw 8

M 0015-050-000 Nut 8
N 4402-010-122 Sliding tray extrusion 2

P 4402-010-131 Sliding tray stop spacer 1

R 0050-093-000 Pan head machine screw 1

T 4402-010-005 Sliding tray assembly 1

U 4402-010-006 Upper cradle assembly 1

V 4402-010-104 Lower cradle 1

W 4402-010-123 Tilt pin 2

EN 40 4402-009-002 Rev AA.1

Item Number Name Quantity

Y 0004-904-000 Socket head cap screw 2

AA 4402-010-149 Support retainer 1

AB 0016-404-000 Serrated flange hex nut 2

AC 4402-010-141 Activation rod 2

AD 4402-010-143 Activation spacer 2

AE 0026-681-000 Roll pin 2

AF 4402-010-153 Flanged bronze bearing 2

AG 0011-640-000 Washer 10
AH 0008-093-000 Shoulder bolt 2
AJ 0016-403-000 Serrated flange hex nut 2

AK 4402-010-128 Lift bar 2

AL 0008-092-000 Shoulder bolt 4
AM 4402-010-129 Side valance 2
AN 0011-641-000 Washer 6
AP 0002-123-000 Button head cap screw 6

4402-009-002 Rev AA.1 41 EN

Stryker Medical
3800 E. Centre Avenue
Portage, MI 49002
USA

4402-009-002 Rev AA.1 2020/12

WCR: AB.12