Scribd
Upload
535 views16 pages

Am Generation Detection

The document discusses amplitude modulation generation and detection. It describes two methods for AM generation: square-law modulation using a nonlinear element and filtering, and switching modulation using a diode. It also covers AM detection using a square-law detector and envelope detector. The envelope detector uses a diode and RC filter to extract the modulating signal by rectifying and filtering the AM wave.

Uploaded by

Anugragha Sundar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
535 views16 pages

Am Generation Detection

The document discusses amplitude modulation generation and detection. It describes two methods for AM generation: square-law modulation using a nonlinear element and filtering, and switching modulation using a diode. It also covers AM detection using a square-law detector and envelope detector. The envelope detector uses a diode and RC filter to extract the modulating signal by rectifying and filtering the AM wave.

Uploaded by

Anugragha Sundar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 16

Amplitude modulationgeneration & detection

Dr. P. Vijayalakshmi Professor / ECE

Flow of the lecture


AM generation
Square-law modulator Switching modulator

Detection of AM waves
Square-law detector Envelope detector

Double side-band suppressed carrier


Time-domain description Frequency-domain description

Generation of DSBSC wave


Balanced modulator Ring modulator

Generation of AM waves
Square-law modulator
requires three features
Means for summing carrier-wave and modulating wave A non-linear element A band-pass filter for extracting the desired modulation products

Semiconductor diodes or transistors are used as non-linear elements Filtering is usually performed by a single or double-tuned filter

Square-law modulator

Non-linear device

m(t) v1(t) c(t) v2(t)

Square-law modulator
Amplitude of the modulating signal is less than the amplitude of the carrier % modulation is less than 100 The transfer characteristic of a diode-load resistor combination is computed Unwanted frequency components are filtered by the tuned filter.

v2 (t ) = a1v1 (t ) + a2v12 (t ) v1 (t ) = Ac cos2f ct + m(t ) v2 (t ) = a1 ( Ac cos2f ct + m(t )) + a2 ( Ac cos2f ct + m(t ))2 = a1 Ac cos2f ct + a1m(t ) + a2 Ac 2 cos2 2f ct + m2 (t ) + 2 Ac cos2f ctm(t )

= a1 Ac cos2f ct + 2a2 Ac cos2f ctm(t ) + a1m(t ) + a2 Ac 2 cos2 2f ct + m2 (t ) 2a2 = a1 Ac cos2f ct 1 + m(t ) a1

Switching modulator

c(t)

m(t) v1(t)

RL v2(t)

Switching modulator
Carrier has larger magnitude than the modulating signal Modulating signal is weaker Less than 100% modulation Diode acts as an ideal switch That is, zero impedance during forward-bias and infinite impedance during reverse bias

v1 ( t ) = m ( t ) + A c cos 2 f c t v 2 ( t ) = v1 ( t ) c(t) > 0 =0 c(t) < 0

Switching modulator
Load voltage v2(t) varies periodically between v1(t) and zero at a rate equal to fc gp(t) is a periodic pulse train with duty cycle equal to one-half and period = 1/fc Fourier series of gp(t) is computed. Output voltage will v1(t)*gp(t)

Switching modulator
1 2 g p (t ) = + cos2f ct + odd harmonics 2 v2 (t ) = [Ac cos2f ct + m(t )]g p (t ) 1 2 v2 (t ) = [Ac cos2f ct + m(t )] + cos 2f ct 2 Ac 2 m(t ) 2 2 = cos 2f ct + Ac cos 2f ct + + m(t ) cos2f ct 2 2 Ac 4 m(t ) cos 2f ct = 1 + 2 Ac

Detection of AM waves
square-law detector

v2 (t ) = a1v1 (t ) + a 2 v1 (t )
2

v1 (t ) = Ac [1 + km(t )]cos 2f c t v2 (t ) = a1 [Ac [1 + km(t )]cos 2f c t ] + a 2 [Ac [1 + km(t )]cos 2f c t ]2 = a1 Ac cos 2f c t + a1km(t ) Ac cos 2f c t Ac 2 cos 2 2f c t 2 2 2 2 + a 2 + Ac k m (t ) cos 2f c t 2 2 + 2 Ac k cos 2f c tm(t )

Square-law detector

v2 (t ) = a1 Ac cos 2f c t + a1km(t ) Ac cos 2f c t Ac 2 cos2 2f c t 2 2 2 2 + a2 + Ac k m (t ) cos 2f c t 2 2 + 2 Ac k cos 2f c tm(t ) 2 Ac 2 2 (1 + cos 4f ct )a2 1 + k m (t ) + 2km(t ) = 2

Envelope detector
Carrier frequency is greater than the modulating frequency Carrier magnitude is greater than the modulating voltage Modulation index is less than one That is % modulation is less than 100 The circuit is combination of a diode and RC-filter

Envelope detector

C RL

vam(t)

Envelope detector
positive half cycle Diode is forward biased Capacitor charges up rapidly to the peak value of the input signal When the input signal falls below a certain vale diode is reverse biased Capacitor discharges slowly through the load resistor Discharging process continues slowly until the next positive half cycle Again when the input is greater than the voltage across the capacitor C , diode starts conducting

Envelope detector
Diode is ideal Zero impedance forward biased Infinite impedance reverse biased Charging time is short compared to the carrier period = 1/fc Capacitor charges rapidly and follows the input voltage

You might also like