Supersedes: 160.73-PW3 (703) Form 160.

73-PW3 (405)

WIRING DIAGRAM, MAXE™

PRODUCT DRAWING MODEL YK (STYLE F) LIQUID CHILLERS
OPTIVIEW CONTROL CENTER
YORK INTERNATIONAL CORPORATION
P.O. Box 1592, York, PA 17405 WITH VARIABLE FREQUENCY DRIVE
CONTRACTOR _______________________ PURCHASER ____________________________________________
ORDER NO. _________________________ JOB NAME ______________________________________________
YORK CONTRACT NO. _________________ LOCATION _____________________________________________
YORK ORDER NO. ____________________ ENGINEER ______________________________________________

REFERENCE DATE ________ APPROVAL DATE ________ CONSTRUCTION DATE ________

JOB DATA:

CHILLER MODEL NO. YK ________________________________________________________

NO. OF UNITS _____________
COMPRESSOR MOTOR ______________ VOLTS, 3-PHASE, _____________ Hz
OIL PUMP MOTOR _____________ VOLTS, 3-PHASE, _____________ Hz, _____________FLA

REMARKS:
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM
(UL APPLICATIONS ONLY)

LD10895

FIG. 1 – ELEMENTARY DIAGRAM (UL APPLICATIONS ONLY)

2 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM (CON'T)

(UL APPLICATIONS ONLY)

LD10896

ELEMENTARY DIAGRAM (UL APPLICATIONS ONLY) (CONT)

YORK INTERNATIONAL 3
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM
(CE APPLICATIONS ONLY)

LD10897

FIG. 2 – ELEMENTARY DIAGRAM (CE APPLICATIONS ONLY)

4 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM (CON'T)

(CE APPLICATIONS ONLY)

LD10898

ELEMENTARY DIAGRAM (CE APPLICATIONS ONLY) (CON'T)

YORK INTERNATIONAL 5
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM

FIG. 3 – ELEMENTARY DIAGRAM LD10899

6 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM (CON'T)

ELEMENTARY DIAGRAM (CON'T) LD10900

YORK INTERNATIONAL 7
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM (MICROBOARD 031-02430)

FIG. 4 – ELEMENTARY DIAGRAM (MICROBOARD 031-02430) LD10901

8 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

ELEMENTARY DIAGRAM (MICROBOARD 031-02430)(CON'T)

ELEMENTARY DIAGRAM (MICROBOARD 031-02430) (CON'T) LD10902

YORK INTERNATIONAL 9
 FORM 160.73-PW3 (405)

LEGEND

LD09000

10 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

DISPLAY INTERFACE BOARD

LD10915

FIG. 5 – DISPLAY INTERFACE BOARD

NOTES:
1. This wiring diagram describes the standard electronic 10. For wiring diagram of V.S.D refer to product form
control scheme for use with a YORK V.S.D. for details 160.49-PW9.
of standard modifications, refer to Product Form 160.54- 11. A jumper is installed between terminals 24 & 25 for
PW7. normal operation.
2. Field wiring to be in accordance with the National CAUTION: The jumper is the only connection permitted
Electrical Code as well as all other applicable codes and between terminals 24 & 25 . Connections of any other
specifications. See Product Form 160.54-PW6 for field devices to either terminals 24 & 25 may cause inadver-
wiring connections. tent compressor start-up.
3. Numbers along the left side of diagram are line identi- 12. Stop contact on V.S.D logic board is set to trip at 105%
fication numbers. The numbers along the right side indicate FLA.
the line number location of relay contacts. An underlined
contact location signifies a normally closed contact. 13. Contact rating is 5 Amps resistive @ 250 Volts A.C. &
30 Volts D.C., 2 Amp Inductive (.4 PF) @ 250 Volts A.C.
4. Main control panel Class 1 field wiring terminal con- & 30 Volts D.C.
nection points are indicated by numbers within a rectangle,
i.e. 15 . Main control panel factory wiring terminal con- 14. Field connected control power supply is not required,
nection points are indicated by numbers within a triangle, as control transformer is supplied on the V.S.D.
i.e. 5 . Component terminal markings are indicated by 15. For high and low voltage units, the factory supplied
numbers within a circle, i.e. C1 . Numbers adjacent to jumper between 15 & 53 must be removed when elec-
circuit lines are the circuit identification numbers. tromechanical starter overloads and/or safety devices
5. To cycle unit on and off automatically with contacts are used. For high voltage (2300-4160) UL and CUL ap-
other than those shown, install a cycling device between proved units only. Elecromechanical compressor motor
terminals 1 & 13 (line 37) (see note 7). If a cycling starter overloads (normally closed) must be connected
device is installed, jumper must be removed between between 15 & 53 .
terminals 1 & 13 . 16. Each 115VAC field-connected inductive load: i.e. relay
6. To stop unit and not permit it to start again, install a coil, motor starter coil, etc., shall have a transient sup-
stop device between terminals 1 & 8 (Line 33) (see pressor wired in parallel with its coil, physically located
note 7). A remote start-stop switch may be connected at the coil. Spare transient suppressors and control circuit
to terminals 1 , 7 & 8 (Lines 32 & 33) (see note 7). fuses are supplied in a bag attached to green ground
Remote start-stop switch (Line 32) is operative only in screw in lower left corner of control panel.
the “remote” operating mode. 17. Resistor for use with Belimo actuator. Remove resis-
7. Device contact rating to be 5 milliamperes @ 115 volts tor if hot gas actuator is a Dodge Engineering, Bray or
A.C. Landis-Staefa actuator.
8. Contact rating is 5 Amps resistive @ 120 volts A.C. or
240 volts A.C.

YORK INTERNATIONAL 11
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM
(UL APPLICATIONS ONLY)

LD10903
FIG. 6 – CONNECTION DIAGRAM (UL APPLICATIONS ONLY)

12 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM (CON'T)

(UL APPLICATIONS ONLY)

LD10904
CONNECTION DIAGRAM (UL APPLICATIONS ONLY) (CON'T)

YORK INTERNATIONAL 13
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM
(CE APPLICATION ONLY)

FIG. 7 – CONNECTION DIAGRAM (CE APPLICATION ONLY) LD10905

14 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM (CON'T)

(CE APPLICATION ONLY)

LD10906
CONNECTION DIAGRAM (CE APPLICATION ONLY) (CON'T)

YORK INTERNATIONAL 15
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM

FIG. 8 – CONNECTION DIAGRAM LD10907

16 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM (CON'T)

LD10908
CONNECTION DIAGRAM (CON'T)

YORK INTERNATIONAL 17
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM

FIG. 9 – CONNECTIONS TO CONTROL PANEL

LD10909

18 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM (CON'T)

CONNECTIONS TO CONTROL PANEL (CON'T) LD10910

YORK INTERNATIONAL 19
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM

FIG. 10 – CONNECTION DIAGRAM LD10911

20 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

CONNECTION DIAGRAM (CON'T)

CONNECTION DIAGRAM (CON'T) LD10912

YORK INTERNATIONAL 21
 FORM 160.73-PW3 (405)

VARIABLE SPEED OIL PUMP DRIVE PANEL

FIG. 11 – WIRING FOR 380V THRU 480V UNITS LD10913

22 YORK INTERNATIONAL
 FORM 160.73-PW3 (405)

PRESSURE - TEMPERATURE CHART

LD10914

YORK INTERNATIONAL 23
P.O. Box 1592, York, Pennsylvania USA 17405-1592 (717) 771-7890 Subject to change without notice. Printed in USA
Copyright © by YORK International Corporation 2005 www.york.com ALL RIGHTS RESERVED
Form 160.73-PW3 (405)
Supersedes: 160.73-PW3 (703)