MATERIAL
MATERIAL SAFETY DATA SHEET

ZELLTECH™ radiant heat barrier

SECTION 1 : IDENTIFICATION OF THE MATERIAL …………………………………………………………………………. 

PRODUCT NAME : ZELLTECH™ RADIANT HEAT BARRIER  

RECOMMENDED
RECOMMENDED USE : used as reflective insulation in roofs, walls and floors of domestic,
industrial and commercial buildings.
WEBSITE : www.zelltech-insulation.com 
:  www.zelltech-insulation.com 
IMPORTANT NOTICE : This material safety data sheet ( M
MSDS
SDS ) is issued by the supplier.
The information in it must not be altered, deleted or added to.
The supplier will not accept any responsibility for any changes made to
Its MSDS by any other person or organization.
The supplier will issue a new MSDS when there is a change in product
specifications,, guidelines or regulations.
specifications

IDENTIFICATION ………………………………………………………………………………………. 
SECTION 2 : HAZARDS IDENTIFICATION 
These products are not considered to be hazardous, and are not classified as ‘controlled
products’. They are comprised principally of Polyethyl ene and Pure Aluminium foil that are non
hazardous.

SECTION 3 : FIRST AID MEASURES ………………………………………………………………………………………………. 

EYE CONTACT
CONTACT : check for and remove any contact lenses. In case of contact, immediately flush
eyes with plenty of water for at least 15 minutes. Get medical attention if irritation occurs.
SKIN CONTACT : no skin reaction would be expected from contact with the product. Wash with
soap and water. Cover the irritated skin with an emollient. Get medical attention if irritation
develops.

SECTION 3 : PHYSICAL DATA ……………………………………………………………………………………………………….. 

BOILING POINT : 2327°C ( Aluminium foil )
MELTING POINT : 660°C ( Aluminiu
Aluminiumm foil )
TEMP. RANGE : - 40°F TO 200°F
WATER VAPOUR PERM: < 0.001 PERMS
APPEARANCE : FLEXIBLE SHEET
ODOUR : NONE
SCRATCH RESISTANCE : BOTH SIDES
REFLECTIVITY : 96%
MIL STANDARD 810 FOG TEST : NO DEFECTS OBSERVED
MIL STANDARD 810 HUMIDITY TEST : NO DEFECTS OBSERVED
 

SECTION 4 : FIRE AND EXPLOSION DATA …………………………………………………………………………………….. 

Flammability of tthe
he pro
product
duct : N
Non
on – Flammable
Auto ignition temperature : Not available
Flash point : Not available
Flammable limits : Not available
Usual Fire hazards : Radiant Barrier foil materials are not highly flammable, but in
contact with flame they will melt and burn.

SECTION 5 : FIRE FIGHTING MEASURES ………………………………………………………………………………………. 

Specific Hazards : Not Flammable – delaminates above 90°C
Extinguishing Media : use extinguishing media (e.g. CO2, foam or Dry chemical) and
equipment as required if fire in surrounding materials.
Fire fighting procedures : if product is present in a fire, some smoke and toxic gasses may be
evolved. Wear protective equipment including Self Contained Breathing Apparatus
Apparatus ( SCBA )
when combating fire.
Hazardous decomposition
decomposition products. : when heated above 120°C, the adhesive may break down
releasing chlorine and hydrogen chloride.

SECTION 6 : HANDLING & STORAGE …………………………………………………………………………………………… 

Generally the products require no special precautions when handling, However the products
may become slippery when wet, and care should be taken when walking on this.
Storage : Keep in a dry sheltered environment, Keep container tightly closed, Keep in a cool and
well ventilated area.
Keep away from incompatibles such as oxidizing agents,
age nts, acids, alkalis.

SECTION 7 : STABILITY AND REACTIVITY ……………………………………………………………………………………..

..  
CHEMICAL STABILITY : STABLE
INCOMPATIBILITY MATERIALS : NONE
REACTIVITY
REACTIVITY : reactive with oxidizing agents, acid, alkalis.
CONDITION TO AVOID : HEATING TO OVER 120°C
HAZARDOUS DECOMPOSITION : when heated above 120°C, the adhesive may break down
releasing chlorine and hydrogen chloride.
HAZARDOUS POLYMERISATION : NONE
POLYMERIZATION
POLYMERIZATION : Will not occur
Corrosivity : Not available

SECTION 8 : TOXICOLOGICAL INFORMATION ……………………………………………………………………………..

..  
Toxicological data is not applicable to the solid material.
Health effects ( applicable to any fumes due to overheating above 120°C )
Acute effects : when heated above 120°C, the adhesive may break down releasing chlorine

and hydrogen chloride.

Swallowed : unlikely under normal use.
Eye : in situations overheating above 120°C fumes will irritate the eyes causing
Watering and redness.
 

Skin : in situations overheating above 120°C fumes may cause mild skin irritation
Inhaled : in situations overheating above 120°C highly irritant smoke or fumes may
cause excess mucous secretion, coughing and lung damage.

SECTION 9 : ECOLOGICAL INFORMATION …………………………………………………………………………………..

..  
ECOTOXICITY
ECOTOXICITY : no known reports of ecotoxicity
Degradability : product would be expected to be of low bio-degradability
Recyclable : aluminium foil is 100% recyclable and environment friendly
Mobility : low mobility in landfill situations.

SECTION 10 : DISPOSAL CONSIDERATIONS ………………………………………………………………………………… 

Collect off-cuts and waste material.
Dispose into landfill site in accordance
accordance with relevant authority guidelines.

SECTION 11 : TRANSPORT INFORMATION ………………………………………………………………………………….

Transport requirements : no special transport requirements are necessary.
Incompatibilities : none
Marine pollutant : No
DOT classification : not a DOT controlled material ( United States )

SECTION 12 : Other Regulatory Information ……………………………………………………………………………… 

Federal and State Regulations:
California prop 65: This product contains the following ingredients for which the State of
California has found to cause birth defects which would require a warning under the statute:
No products were found.
California prop. 65: This product contains the following ingredients for which The State of
California has found to cause
cause cancer which would require warning under the statute
statute :
No products were found.
ASTM ( American Standard Testing Methods ) : ASTM D-882, ASTM D1938, ASTM C 1338-00
ASTM C 1136-92, MIL Standard

SECTION 13 : OTHER INFORMATION …………………………………………………………………………………………… 

ISSUED : September 10, 2012
The information above is believed to be accurate and represents the best information currently
available to us. However, we make no warranty of merchantability or any other warranty,
express or implied, with respect to such information, and we assume no liability resulting from
its use. Users should make their own investigations to determine the suitability of the
information for their particular purposes. In no event shall Zelltech inc. be liable for any claims,
losses, or damages of any third party or for lost profits or any special, indirect, incidental,
consequential or exemplary damages, howsoever arising, even if Zelltech inc. has been advised

of the possibility of such damages.