DESIGN OF TWO-WAY SLAB (SLAB 1)-FLOOR LEVEL 2-5

SLAB 1- CASE 3
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 2.4 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 8.34 Kpa
CASE 3 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.064
­Mu = (Ca)(wu)(s2)
= 6.53856 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.032
­Mu = (Ca)(wu)(s2)
= 3.26928 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.049
­Mu = (Cb)(wu)(L2)
= 8.27537 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.025
­Mu = (Cb)(wu)(L ) 2

= 4.22213 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.048
+Mu = (Ca)(wu)(S2)
= 4.90392 KN·m
2.) LONG SPAN, C b= 0.016
 NEGATIVE MOMENT (KN·m)
SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 6.53856 3.26928
LONG 8.27537 4.22213

SPAN POSITIVE MOMENT (KN·m)

SHORT 4.90392
LONG 2.70216
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 6.53856 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.32671
r

= 0.0049691
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 3.26928 KN·m
Rn = Mu/øbd2
= 0.66336
r =

= 0.002447
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 8.27537 KN·m

Rn = Mu/øbd2
= 1.18735
r =

= 0.004433
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 4.22213 KN·m

Rn = Mu/øbd2
= 0.60579
r =

= 0.002232
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Short Span (Positive Moment)

+Mu = 4.90392 KN·m

Rn = Mu/øbd2
= 0.99503
r =

= 0.003698
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Positive Moment)

+Mu = 2.70216 KN·m

Rn = Mu/øbd2
= 0.38771
r =

= 0.001422
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
 DESIGN OF TWO-WAY SLAB (SLAB 1)-FLOOR LEVEL RD
SLAB 1- CASE 3 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.08889 S 3.5 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Wclassroom 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
WU = 7.624 Kpa
CASE 3 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.064
­Mu = (Ca)(wu)(s2)
= 5.97722 KN·m \use
1.2)SHORT SPAN (Discontinuous C a= 0.032
­Mu = (Ca)(wu)(s2)
= 2.98861 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.049
­Mu = (Cb)(wu)(L2) say
= 7.56491 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.025
­Mu = (Cb)(wu)(L ) 2

= 3.85965 KN·m
B. FOR POSITIVE MOMENTS
1.)
SHORT SPAN, C a= 0.048
+Mu = (Ca)(wu)(S2)
= 4.48291 KN·m
2.)LONG SPAN, Cb= 0.016
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
5.97722 2.98861 Rn
7.56491 3.85965
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 4.48291
LONG 2.47018 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 5.97722 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 1.21281 rmin
r
\use r
= 0.004531 ASTEEL
rmin = rmax = Use ø
ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.005091
ASTEEL = 376.7273 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
THEREFORE USE SPACIN = 300 mm
SAY SPACING = 300 mm
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 2.98861 KN·m
= Mu/øbd2 ­Mu =
= 0.60641 Rn =
= =
r =
= 0.002234
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.005091 =
= 376.7273 \use r =
= 12 mm ASTEEL =
= 113.0973 mm 2
Use ø =
= 3.331 ABAR =
» 4 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 300.2101 = 300 SPACING, S = (A B/AS)x1000
=
THEREFORE USE SPAC = 300 mm
SAY SPACI = 300 mm THEREFORE USE SPAC
SAY SPACI
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

7.56491 KN·m ­Mu = 3.85965

Mu/øbd2 Rn = Mu/øbd2
1.08542 = 0.55378
r =

0.004043 = 0.002038
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.005091 \use r = 0.005091
376.7273 ASTEEL = 376.7273
12 mm Use ø = 12
113.0973 mm2 ABAR = 113.0973
3.331 N = 3.331
4 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
300.2101 = 300 = 300.2101

= 300 mm THEREFORE USE SPAC =

= 300 mm SAY SPACI =

``
 For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 4.48291 KN·m

Rn = Mu/øbd2
= 0.90961
r =

= 0.003374
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
mm Use ø = 12 mm
mm2 ABAR = 113.0973 mm2
N = 3.331
say N » 4
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 300.2101

300 mm THEREFORE USE SPAC = 300

300 mm SAY SPACI = 300

``
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 2.47018 KN·m

Rn = Mu/øbd2
= 0.35442
r =

= 0.001299
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 300.2101

mm THEREFORE USE SPAC = 300 mm

mm SAY SPACI = 300 mm

``
 0.037292

MAX SPACING = 3h
= 300

``
 +Mu = (Cb)(wu)(L2)
= 2.70216 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 2)-FLOOR LEVEL 2-5
SLAB 2- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08333 S 3
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.667
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Corridors above 3.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 ground floor= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 10.58 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s2)
= 5.23710 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 7.07009 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 3.90402 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 5.35613 KN·m
 SPAN NEGATIVE MOMENT (KN·m)
SHORT 5.23710
LONG 7.07009

SPAN POSITIVE MOMENT (KN·m)

SHORT 3.90402
LONG 5.35613

Design of Rebars For Short Span (Negative Moment)

­Mu = 5.23710 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.06264
r

= 0.0039559
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm
Design of Rebars For Long Span (Negative Moment)
-Mu = = 7.07009 KN·m
Rn = Mu/øbd2
= 1.01442
r =

= 0.003772
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Short Span (Positive Moment)
+Mu = 3.90402 KN·m
Rn = Mu/øbd2
= 0.79215
r =

= 0.002931
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Positive Moment)
+Mu = 5.35613 KN·m
Rn = Mu/øbd2
= 0.76850
r =

= 0.002842
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
+Mu =(Cb)(wu)(L2)
2.47018 KN·m
 DESIGN OF TWO-WAY SLAB (SLAB 2)-FLOOR LEVEL 2-5
SLAB 2- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08333 S 3
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.667
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Corridors above 3.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 ground floor= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 10.58 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.062
­Mu = (Ca)(wu)(s2)
= 5.90364 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.031
­Mu = (Ca)(wu)(s2)
= 2.95182 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L2)
= 8.78405 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L2)
= 4.49915 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.047
+Mu = (Ca)(wu)(S )
2
 NEGATIVE MOMENT (KN·m)
SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 5.90364 2.95182
LONG 8.78405 4.49915

SPAN POSITIVE MOMENT (KN·m)

SHORT 4.47534
LONG 6.64160
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 5.90364 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.19788
r

= 0.0044732
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 2.95182 KN·m
Rn = Mu/øbd2
= 0.59894
r =

= 0.002207
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 8.78405 KN·m

Rn = Mu/øbd2
= 1.26034
r =

= 0.004713
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 4.49915 KN·m

Rn = Mu/øbd2
= 0.64554
r =

= 0.002381
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Short Span (Positive Moment)

+Mu = 4.47534 KN·m

Rn = Mu/øbd2
= 0.90807
r =

= 0.003369
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Positive Moment)

+Mu = 6.64160 KN·m

Rn = Mu/øbd2
= 0.95294
r =

= 0.003539
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
 DESIGN OF TWO-WAY SLAB (SLAB 2)-FLOOR LEVEL RD
SLAB 2- CASE 2 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.08333 S 3 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.667
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
WU = 24.232 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.062
­Mu = (Ca)(wu)(s2)
= 13.52146 KN·m \use
1.2)SHORT SPAN (Discontinuous C a= 0.031
­Mu = (Ca)(wu)(s2)
= 6.76073 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.041
­Mu = (Cb)(wu)(L2) say
= 20.11862 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.021
­Mu = (Cb)(wu)(L2)
= 10.30466 KN·m
B. FOR POSITIVE MOMENTS
1.)
SHORT SPAN, C a= 0.047
+Mu = (Ca)(wu)(S )
2
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
13.52146 6.76073 Rn
20.11862 10.30466
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 10.25014
LONG 15.21164 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 13.52146 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 2.74358 rmin
r
\use r
= 0.01064 ASTEEL
rmin = rmax = Use ø
ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.01064
ASTEEL = 787.375 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 6.961924
N » 7
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 143.6385 = 300
THEREFORE USE SPACIN = 143.6385 mm
SAY SPACING = 140 mm
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 6.76073 KN·m
= Mu/øbd2 ­Mu =
= 1.37179 Rn =
= =
r =
= 0.005143
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.005143 =
= 380.6098 \use r =
= 12 mm ASTEEL =
= 113.0973 mm2 Use ø =
= 3.36533 ABAR =
» 4 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 297.1477 = 300 SPACING, S = (A B/AS)x1000
=
THEREFORE USE SPAC = 297.1477 mm
SAY SPACI = 290 mm THEREFORE USE SPAC
SAY SPACI
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

20.11862 KN·m ­Mu = 10.30466

Mu/øbd2 Rn = Mu/øbd2
2.88662 = 1.47851
r =

0.011237 = 0.005557
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.011237 \use r = 0.005557
831.5287 ASTEEL = 411.2503
12 mm Use ø = 12
113.0973 mm2 ABAR = 113.0973
7.352328 N = 3.636251
8 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
136.0113 = 300 = 275.0085

= 136.0113 mm THEREFORE USE SPAC =

= 130 mm SAY SPACI =

``
 For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 10.25014 KN·m

Rn = Mu/øbd2
= 2.07981
r =

= 0.007932
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.007932
ASTEEL = 586.9437
mm Use ø = 12 mm
mm2 ABAR = 113.0973 mm2
N = 5.189722
say N » 6
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 192.6885

275.0085 mm THEREFORE USE SPAC = 192.6885

275 mm SAY SPACI = 190

``
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 15.21164 KN·m

Rn = Mu/øbd2
= 2.18257
r =

= 0.008345
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008345
ASTEEL = 617.5115
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.46
say N » 6
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 183.1502

mm THEREFORE USE SPAC = 183.1502 mm

mm SAY SPACI = 180 mm

``
 0.037292

MAX SPACING = 3h
= 300

``
 = 4.47534 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 6.64160 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 3)-FLOOR LEVEL 2-5
SLAB 3- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.09444 S 4
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.889
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Corridors above 3.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 ground floor= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 10.58 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.048
­Mu = (Ca)(wu)(s )
2

= 8.12544 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.024
­Mu = (Ca)(wu)(s )
2

= 4.06272 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L )
2

= 8.78405 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L2)
= 4.49915 KN·m
B. FOR POSITIVE MOMENTS
 NEGATIVE MOMENT (KN·m)
SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 8.12544 4.06272
LONG 8.78405 4.49915

SPAN POSITIVE MOMENT (KN·m)

SHORT 6.09408
LONG 6.64160
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 8.12544 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.64870
r

= 0.0062222
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0062222
ASTEEL = 460.44103
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 4.0711925
say N » 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 245.62828 = 300
THEREFORE USE SPACING = 245.62828 mm
SAY SPACING = 245 mm
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 4.06272 KN·m
Rn = Mu/øbd2
= 0.82435
r =

= 0.003052
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 8.78405 KN·m

Rn = Mu/øbd2
= 1.26034
r =

= 0.004713
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 4.49915 KN·m

Rn = Mu/øbd2
= 0.64554
r =

= 0.002381
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Short Span (Positive Moment)

+Mu = 6.09408 KN·m

Rn = Mu/øbd2
= 1.23652
r =

= 0.004622
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Positive Moment)

+Mu = 6.64160 KN·m

Rn = Mu/øbd2
= 0.95294
r =

= 0.003539
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
 = 10.25014 KN·m
2.)LONG SPAN, Cb= 0.031
+Mu =(Cb)(wu)(L2)
15.21164 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 3)-FLOOR LEVEL RD
SLAB 3- CASE 2 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.09444 S 4 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.889
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
WU = 24.232 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.048
­Mu = (Ca)(wu)(s )
2

= 18.61018 KN·m \use

1.2)SHORT SPAN (Discontinuous C a= 0.024
­Mu = (Ca)(wu)(s )
2

= 9.30509 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.041
­Mu = (Cb)(wu)(L )
2
say
= 20.11862 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.021
­Mu = (Cb)(wu)(L2)
= 10.30466 KN·m
B. FOR POSITIVE MOMENTS
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
18.61018 9.30509 Rn
20.11862 10.30466
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 13.95763
LONG 15.21164 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 18.61018 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 3.77611 rmin
r
\use r
= 0.015061 ASTEEL
rmin = rmax = Use ø
ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.015061
ASTEEL = 1114.495 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 9.854298
N » 10
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 101.4786 = 300
THEREFORE USE SPACIN = 101.4786 mm
SAY SPACING = 100 mm
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 9.30509 KN·m
= Mu/øbd2 ­Mu =
= 1.88805 Rn =
= =
r =
= 0.007167
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.007167 =
= 530.3346 \use r =
= 12 mm ASTEEL =
= 113.0973 mm2 Use ø =
= 4.689187 ABAR =
» 5 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 213.2566 = 300 SPACING, S = (A B/AS)x1000
=
THEREFORE USE SPAC = 213.2566 mm
SAY SPACI = 210 mm THEREFORE USE SPAC
SAY SPACI
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

20.11862 KN·m ­Mu = 10.30466

Mu/øbd2 Rn = Mu/øbd2
2.88662 = 1.47851
r =

0.011237 = 0.005557
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.011237 \use r = 0.005557
831.5287 ASTEEL = 411.2503
12 mm Use ø = 12
113.0973 mm2 ABAR = 113.0973
7.352328 N = 3.636251
8 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
136.0113 = 300 = 275.0085

= 136.0113 mm THEREFORE USE SPAC =

= 140 mm SAY SPACI =

``
 For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 13.95763 KN·m

Rn = Mu/øbd2
= 2.83208
r =

= 0.011009
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.011009
ASTEEL = 814.6512
mm Use ø = 12 mm
mm2 ABAR = 113.0973 mm2
N = 7.203098
say N » 8
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 138.8291

275.0085 mm THEREFORE USE SPAC = 138.8291

275 mm SAY SPACI = 130

``
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 15.21164 KN·m

Rn = Mu/øbd2
= 2.18257
r =

= 0.008345
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008345
ASTEEL = 617.5115
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.46
say N » 6
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 183.1502

mm THEREFORE USE SPAC = 183.1502 mm

mm SAY SPACI = 180 mm

``
 0.037292

MAX SPACING = 3h
= 300

``
 1.) SHORT SPAN, Ca = 0.036
+Mu = (Ca)(wu)(S2)
= 6.09408 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 6.64160 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 3)-FLOOR LEVEL 2-5
SLAB 3- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.09444 S 4
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.889
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Corridors above 3.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 ground floor= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 10.58 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
= 6.77120 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 7.07009 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 5.07840 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
 SPAN NEGATIVE MOMENT (KN·m)
SHORT 6.77120
LONG 7.07009

SPAN POSITIVE MOMENT (KN·m)

SHORT 5.07840
LONG 5.35613

Design of Rebars For Short Span (Negative Moment)

­Mu = 6.77120 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.37391
r

= 0.0051516
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0051516
ASTEEL = 381.21829
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3707097
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 296.67342 = 300
THEREFORE USE SPACING = 296.67342 mm
SAY SPACING = 296 mm
Design of Rebars For Long Span (Negative Moment)
-Mu = = 7.07009 KN·m
Rn = Mu/øbd2
= 1.01442
r =

= 0.003772
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Short Span (Positive Moment)
+Mu = 5.07840 KN·m
Rn = Mu/øbd2
= 1.03044
r =

= 0.003833
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Positive Moment)
+Mu = 5.35613 KN·m
Rn = Mu/øbd2
= 0.76850
r =

= 0.002842
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 1.)
SHORT SPAN, C a= 0.036
+Mu = (Ca)(wu)(S2)
= 13.95763 KN·m
2.)LONG SPAN, Cb= 0.031
+Mu =(Cb)(wu)(L2)
15.21164 KN·m
 = 5.35613 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 4)-FLOOR LEVEL 2-4

SLAB 4- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 7.54 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s2)
= 5.08008 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.027
­Mu = (Ca)(wu)(s2)
= 2.49386 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L2)
= 6.26009 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
 SAY SPACING = 290 mm

NEGATIVE MOMENT (KN·m)

SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 5.08008 2.49386
LONG 6.26009 3.20639

SPAN POSITIVE MOMENT (KN·m)

SHORT 3.78697
LONG 4.73324
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 5.08008 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.03078
r

= 0.0038345
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 2.49386 KN·m
Rn = Mu/øbd2
= 0.50602
r =

= 0.00186
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 6.26009 KN·m

Rn = Mu/øbd2
= 0.89820
r =

= 0.003331
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 3.20639 KN·m

Rn = Mu/øbd2
= 0.46005
r =

= 0.00169
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Short Span (Positive Moment)

+Mu = 3.78697 KN·m

Rn = Mu/øbd2
= 0.76840
r =

= 0.002841
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
Design of Rebars For Long Span (Positive Moment)

+Mu = 4.73324 KN·m

Rn = Mu/øbd2
= 0.67913
r =

= 0.002506
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``
 DESIGN OF TWO-WAY SLAB (SLAB 4)-FLOOR LEVEL RD
SLAB 4- CASE 2 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.08889 S 3.5 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
WU = 24.232 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.055
­Mu = (Ca)(wu)(s2)
= 16.32631 KN·m \use
1.2)SHORT SPAN (Discontinuous C a= 0.027
­Mu = (Ca)(wu)(s2)
= 8.01473 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.041
­Mu = (Cb)(wu)(L2) say
= 20.11862 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.021
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
16.32631 8.01473 Rn
20.11862 10.30466
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 12.17052
LONG 15.21164 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 16.32631 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 3.31270 rmin
r
\use r
= 0.013043 ASTEEL
rmin = rmax = Use ø
ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.013043
ASTEEL = 965.2048 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 8.534284
N » 9
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 117.1744 = 300
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 8.01473 KN·m
= Mu/øbd2 ­Mu =
= 1.62623 Rn =
= =
r =
= 0.006134
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.006134 =
= 453.9245 \use r =
= 12 mm ASTEEL =
= 113.0973 mm2 Use ø =
= 4.013574 ABAR =
» 5 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 249.1545 = 300 SPACING, S = (A B/AS)x1000
=
THEREFORE USE SPAC = 249.1545 mm
SAY SPACI = 240 mm THEREFORE USE SPAC
SAY SPACI
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

20.11862 KN·m ­Mu = 10.30466

Mu/øbd 2
Rn = Mu/øbd2
2.88662 = 1.47851
r =

0.011237 = 0.005557
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.011237 \use r = 0.005557
831.5287 ASTEEL = 411.2503
12 mm Use ø = 12
113.0973 mm 2
ABAR = 113.0973
7.352328 N = 3.636251
8 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
136.0113 = 300 = 275.0085

= 136.0113 mm THEREFORE USE SPAC =

= 130 mm SAY SPACI =

``
 For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 12.17052 KN·m

Rn = Mu/øbd2
= 2.46947
r =

= 0.00951
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00951
ASTEEL = 703.7361
mm Use ø = 12 mm
mm 2
ABAR = 113.0973 mm2
N = 6.222394
say N » 7
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 160.7099

275.0085 mm THEREFORE USE SPAC = 160.7099

275 mm SAY SPACI = 160

``
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 15.21164 KN·m

Rn = Mu/øbd2
= 2.18257
r =

= 0.008345
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008345
ASTEEL = 617.5115
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.46
say N » 6
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 183.1502

mm THEREFORE USE SPAC = 183.1502 mm

mm SAY SPACI = 180 mm

``
 0.037292

MAX SPACING = 3h
= 300

``
 ­Mu = (Cb)(wu)(L2)
= 3.20639 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 3.78697 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 4.73324 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 4)-FLOOR LEVEL 2-4
SLAB 4- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 7.54 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
= 3.69460 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 5.03861 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 3.69460
LONG 5.03861

SPAN POSITIVE MOMENT (KN·m)

SHORT 2.77095
LONG 3.81713

Design of Rebars For Short Span (Negative Moment)

­Mu = 3.69460 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 0.74966
r

= 0.002771
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
Design of Rebars For Long Span (Negative Moment)
-Mu = = 5.03861 KN·m
Rn = Mu/øbd2
= 0.72294
r =

= 0.002671
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Short Span (Positive Moment)
+Mu = 2.77095 KN·m
Rn = Mu/øbd2
= 0.56224
r =

= 0.00207
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Positive Moment)
+Mu = 3.81713 KN·m
Rn = Mu/øbd2
= 0.54768
r =

= 0.002015
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 ­Mu = (Cb)(wu)(L2)
= 10.30466 KN·m
B. FOR POSITIVE MOMENTS
1.)
SHORT SPAN, C a= 0.041
+Mu = (Ca)(wu)(S2)
= 12.17052 KN·m
2.)LONG SPAN, Cb= 0.031
+Mu =(Cb)(wu)(L2)
15.21164 KN·m
THEREFORE USE SPACIN = 117.1744 mm
SAY SPACING = 110 mm
 = 2.77095 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 3.81713 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 4)-FLOOR LEVEL 5

SLAB 4- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 Dining Room DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 and Restaurant= 4.8 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 15.22 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s2)
= 10.25448 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.027
­Mu = (Ca)(wu)(s2)
= 5.03402 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
 = 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

NEGATIVE MOMENT (KN·m)

SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 10.25448 5.03402
LONG 12.63641 6.47231

SPAN POSITIVE MOMENT (KN·m)

SHORT 7.64425
LONG 9.55436
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 10.25448 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 2.08069
r

= 0.0079352
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0079352
ASTEEL = 587.20494
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 5.1920316
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 5.03402 KN·m
Rn = Mu/øbd2
= 1.02143
r =

= 0.003799
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 12.63641 KN·m

Rn = Mu/øbd2
= 1.81307
r =

= 0.00687
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00687
ASTEEL = 508.3495
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 4.494797
say N » 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 222.4795 = 300

THEREFORE USE SPACING = 222.4795 mm

SAY SPACING = 222 mm
SAY SPACING = 220 mm
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 6.47231 KN·m

Rn = Mu/øbd2
= 0.92865
r =

= 0.003447
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Short Span (Positive Moment)

+Mu = 7.64425 KN·m

Rn = Mu/øbd2
= 1.55106
r =

= 0.00584
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00584
ASTEEL = 432.169
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.821213
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 261.697 = 300

THEREFORE USE SPACING = 261.697 mm

SAY SPACING = 262 mm
SAY SPACING = 260 mm
Design of Rebars For Long Span (Positive Moment)

+Mu = 9.55436 KN·m

Rn = Mu/øbd2
= 1.37086
r =

= 0.00514
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00514
ASTEEL = 380.344
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.362979
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 297.3554 = 300

THEREFORE USE SPACING = 297.3554 mm

SAY SPACING = 297 mm
SAY SPACING = 290 mm
 ­Mu = (Cb)(wu)(L2)
= 12.63641 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L2)
= 6.47231 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 7.64425 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 9.55436 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 4)-FLOOR LEVEL 5
SLAB 4- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 Dining Room DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 and Restaurant= 4.8 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 15.22 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
= 7.45780 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 10.17077 KN·m
 say N » 6
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 192.60283 = 300
THEREFORE USE SPACING = 192.60283 mm
SAY SPACING = 192 mm
SAY SPACING = 190 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 7.45780
LONG 10.17077

SPAN POSITIVE MOMENT (KN·m)

SHORT 5.59335
LONG 7.70513

Design of Rebars For Short Span (Negative Moment)

­Mu = 7.45780 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.51323
r

= 0.0056926
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0056926
ASTEEL = 421.2511
Use ø = 12 mm
ABAR = 113.09734 mm2
Design of Rebars For Long Span (Negative Moment)
-Mu = = 10.17077 KN·m
Rn = Mu/øbd2
= 1.45930
r =

= 0.005483
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005483
ASTEEL = 405.7232
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.587381
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 278.7549 = 300

THEREFORE USE SPACING = 278.7549 mm

SAY SPACING = 278 mm
SAY SPACING = 270 mm
 ``

Design of Rebars For Short Span (Positive Moment)

+Mu = 5.59335 KN·m
Rn = Mu/øbd2
= 1.13492
r =

= 0.004232
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 ``

Design of Rebars For Long Span (Positive Moment)

+Mu = 7.70513 KN·m
Rn = Mu/øbd2
= 1.10553
r =

= 0.00412
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
``
``
 B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 5.59335 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 7.70513 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 5)-FLOOR LEVEL 2-5

SLAB 5- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 7.54 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
= 3.69460 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
 N = 3.7246775
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 268.47962 = 300
THEREFORE USE SPACING = 268.47962 mm
SAY SPACING = 268 mm
SAY SPACING = 260 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 3.69460
LONG 5.03861

SPAN POSITIVE MOMENT (KN·m)

SHORT 2.77095
LONG 3.81713

Design of Rebars For Short Span (Negative Moment)

­Mu = 3.69460 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 0.74966
r

= 0.002771
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
Design of Rebars For Long Span (Negative Moment)
-Mu = = 5.03861 KN·m
Rn = Mu/øbd2
= 0.72294
r =

= 0.002671
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Short Span (Positive Moment)
+Mu = 2.77095 KN·m
Rn = Mu/øbd2
= 0.56224
r =

= 0.00207
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
Design of Rebars For Long Span (Positive Moment)
+Mu = 3.81713 KN·m
Rn = Mu/øbd2
= 0.54768
r =

= 0.002015
rmin = rmax =

= 0.004776 = 0.037292 DESIGN LOADS:

BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 DESIGN OF TWO-WAY SLAB (SLAB 5)-FLOOR LEVEL RD
SLAB 5- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c 27.6 Mpa hmin 0.08889 S 3.5
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
W U= 24.232 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) C a= 0.04
­Mu = (Ca)(wu)(s2)
= 11.87368 KN·m
2.2)LONG SPAN (Continuous Edge) Cb= 0.033
­Mu = (Cb)(wu)(L2)
 SPAN NEGATIVE MOMENT (KN·m)
SHORT 11.87368
LONG 16.19303

SPAN POSITIVE MOMENT (KN·m)

SHORT 8.90526
LONG 12.26745

Design of Rebars For Short Span (Negative Moment)

­Mu = 11.87368 KN·m
Rn = Mu/øbd2
= 2.40924
r

= 0.009264
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.009264
ASTEEL = 685.5247
Use ø = 12 mm
Design of Rebars For Long Span (Negative Moment) Design of Rebars
-Mu = = 16.19303 KN·m
Rn = Mu/øbd2
= 2.32338
r =

= 0.008914
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS
rmin = 1.4/fy
= 0.005091
\use r = 0.008914 \use
ASTEEL = 659.6667
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.832734
say N » 6 say
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 171.4462 = 300

THEREFORE USE SPAC = 171.4462 mm

SAY SPACI = 170 mm
Design of Rebars For Short Span (Positive Moment) Design of Rebars
+Mu = 8.90526 KN·m +Mu
Rn = Mu/øbd2 Rn
= 1.80693
r = r

= 0.006845
rmin = rmax = rmin

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN r
rmin = 1.4/fy rmin
= 0.005091
r = 0.006845 \use r
ASTEEL = 506.5507 ASTEEL
Use ø = 12 mm Use ø
ABAR = 113.0973 mm2 ABAR
N = 4.478892 N
N » 5 say N
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B
= 223.2695 = 300

THEREFORE USE SPACIN = 223.2695 mm THEREFORE USE SPAC

SAY SPACING = 220 mm
 For Long Span (Positive Moment)
= 12.26745 KN·m
= Mu/øbd2
= 1.76014
=

= 0.006661
= rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
= 1.4/fy
= 0.005091
= 0.006661
= 492.8775
= 12 mm
= 113.0973 mm2
= 4.357994
» 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 229.4634 = 300

THEREFORE USE SPAC = 229.4634 mm

SAY SPACI = 220 mm
 = 5.03861 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 2.77095 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 3.81713 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 6)-FLOOR LEVEL 2-5

SLAB 6- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Laboratory= 4.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 12.18 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s2)
= 8.20628 KN·m
 ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

NEGATIVE MOMENT (KN·m)

SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 8.20628 4.02854
LONG 10.11245 5.17955

SPAN POSITIVE MOMENT (KN·m)

SHORT 6.11741
LONG 7.64600
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 8.20628 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.66510
r

= 0.0062865
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0062865
Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)
-Mu = = 4.02854 KN·m
Rn = Mu/øbd2
= 0.81741
r =

= 0.003026
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 10.11245 KN·m

Rn = Mu/øbd2
= 1.45094
r =

= 0.00545
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00545
ASTEEL = 403.3173
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.566108
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 280.4177 = 300
Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 5.17955 KN·m

Rn = Mu/øbd2
= 0.74316
r =

= 0.002747
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
 = 16.19303 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, C a= 0.03
+Mu = (Ca)(wu)(S2)
= 8.90526 KN·m
2.) LONG SPAN, Cb= 0.025
+Mu = (Cb)(wu)(L2)
12.26745 KN·m

Design of Rebars For Short Span (Positive Moment)

+Mu = 6.11741 KN·m

Rn = Mu/øbd2
= 1.24126
r =

= 0.00464
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
 ABAR = 113.0973 mm2
N = 6.061369
say N » 7
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 164.9792 = 300
THEREFORE USE SPACING = 164.9792 mm
SAY SPACING = 160 mm

Design of Rebars For Long Span (Positive Moment)

+Mu = 7.64600 KN·m

Rn = Mu/øbd2
= 1.09705
r =

= 0.004087
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
 DESIGN OF TWO-WAY SLAB (SLAB 6)-FLOOR LEVEL RD
SLAB 6- CASE 2 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.08889 S 3.5 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
WU = 24.232 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.055
­Mu = (Ca)(wu)(s2)
= 16.32631 KN·m \use
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
16.32631 8.01473 Rn
20.11862 10.30466
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 12.17052
LONG 15.21164 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 16.32631 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 3.31270 rmin
r
\use r
= 0.013043 ASTEEL
rmin = rmax = Use ø
ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.013043
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 8.01473 KN·m
= Mu/øbd2 ­Mu =
= 1.62623 Rn =
= =
r =
= 0.006134
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.006134 =
= 453.9245 \use r =
= 12 mm ASTEEL =
= 113.0973 mm2 Use ø =
= 4.013574 ABAR =
» 5 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 249.1545 = 300 SPACING, S = (A B/AS)x1000
=
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

20.11862 KN·m ­Mu = 10.30466

Mu/øbd2 Rn = Mu/øbd2
2.88662 = 1.47851
r =

0.011237 = 0.005557
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.011237 \use r = 0.005557
831.5287 ASTEEL = 411.2503
12 mm Use ø = 12
113.0973 mm2 ABAR = 113.0973
7.352328 N = 3.636251
8 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
136.0113 = 300 = 275.0085
 For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 12.17052 KN·m

Rn = Mu/øbd2
= 2.46947
r =

= 0.00951
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00951
ASTEEL = 703.7361
mm Use ø = 12 mm
mm2 ABAR = 113.0973 mm2
N = 6.222394
say N » 7
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 160.7099
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 15.21164 KN·m

Rn = Mu/øbd2
= 2.18257
r =

= 0.008345
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008345
ASTEEL = 617.5115
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.46
say N » 6
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 183.1502
 0.037292

MAX SPACING = 3h
= 300
 1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.027
­Mu = (Ca)(wu)(s2)
= 4.02854 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L2)
= 10.11245 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L ) 2

= 5.17955 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 6.11741 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 7.64600 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 7)-FLOOR LEVEL 2 and 5
SLAB 7 CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 7.54 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
 ASTEEL = 465.2038
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 4.1133047
say N » 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 243.11353 = 300
THEREFORE USE SPACING = 243.11353 mm
SAY SPACING = 243 mm
SAY SPACING = 240 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 3.69460
LONG 5.03861

SPAN POSITIVE MOMENT (KN·m)

SHORT 2.77095
LONG 3.81713

Design of Rebars For Short Span (Negative Moment)

­Mu = 3.69460 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 0.74966
r

= 0.002771
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

Design of Rebars For Long Span (Negative Moment)

-Mu = = 5.03861 KN·m
Rn = Mu/øbd2
= 0.72294
r =

= 0.002671
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
 THEREFORE USE SPACING = 280.4177 mm
SAY SPACING = 280 mm
SAY SPACING = 280 mm

``

Design of Rebars For Short Span (Positive Moment)

+Mu = 2.77095 KN·m
Rn = Mu/øbd2
= 0.56224
r =

= 0.00207
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

``

Design of Rebars For Long Span (Positive Moment)

+Mu = 3.81713 KN·m
Rn = Mu/øbd2
= 0.54768
r =

= 0.002015
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

``
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

``
 1.2)SHORT SPAN (Discontinuous C a= 0.027
­Mu = (Ca)(wu)(s2)
= 8.01473 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.041
­Mu = (Cb)(wu)(L2) say
= 20.11862 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.021
­Mu = (Cb)(wu)(L )
2

= 10.30466 KN·m
B. FOR POSITIVE MOMENTS
1.)
SHORT SPAN, C a= 0.041
+Mu = (Ca)(wu)(S2)
= 12.17052 KN·m
2.)LONG SPAN, Cb= 0.031
+Mu =(Cb)(wu)(L2)
15.21164 KN·m
ASTEEL = 965.2048 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 8.534284
N » 9
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 117.1744 = 300
THEREFORE USE SPACIN = 117.1744 mm
SAY SPACING = 117 mm
SAY SPACING = 110 mm
THEREFORE USE SPAC = 249.1545 mm
SAY SPACI = 240 mm THEREFORE USE SPAC
SAY SPACI
SAY SPACI
= 136.0113 mm THEREFORE USE SPAC =
= 136 mm SAY SPACI =
= 130 mm

``
275.0085 mm THEREFORE USE SPAC = 160.7099
275 mm SAY SPACI = 160

``
mm THEREFORE USE SPAC = 183.1502 mm
mm SAY SPACI = 180 mm

``
``
 = 3.69460 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 5.03861 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 2.77095 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 3.81713 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 7)-FLOOR LEVEL 3 and 4

SLAB 7 CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Assembly Areas 6 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 and Auditorium= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 14.1 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
 \use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 6.90900
LONG 9.42233

SPAN POSITIVE MOMENT (KN·m)

SHORT 5.18175
LONG 7.13813

Design of Rebars For Short Span (Negative Moment)

­Mu = 6.90900 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.40187
r

= 0.0052599
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

Design of Rebars For Long Span (Negative Moment)

-Mu = = 9.42233 KN·m
Rn = Mu/øbd2
= 1.35192
r =

= 0.005067
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

Design of Rebars For Short Span (Positive Moment)

+Mu = 5.18175 KN·m
Rn = Mu/øbd2
= 1.05141
r =

= 0.003913
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
 THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm

Design of Rebars For Long Span (Positive Moment)

+Mu = 7.13813 KN·m
Rn = Mu/øbd2
= 1.02418
r =

= 0.003809
rmin = rmax =

= 0.004776 = 0.037292 DESIGN LOADS:

BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
 DESIGN OF TWO-WAY SLAB (SLAB 7)-FLOOR LEVEL RD
SLAB 7 CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c 27.6 Mpa hmin 0.08889 S 3.5
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
W U= 24.232 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) C a= 0.04
 SPAN NEGATIVE MOMENT (KN·m)
SHORT 11.87368
LONG 16.19303

SPAN POSITIVE MOMENT (KN·m)

SHORT 8.90526
LONG 12.26745

Design of Rebars For Short Span (Negative Moment)

­Mu = 11.87368 KN·m
Rn = Mu/øbd2
= 2.40924
r

= 0.009264
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
Design of Rebars For Long Span (Negative Moment) Design of Rebars
-Mu = = 16.19303 KN·m
Rn = Mu/øbd2
= 2.32338
r =

= 0.008914
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS
rmin = 1.4/fy
= 0.005091
\use r = 0.008914 \use
ASTEEL = 659.6667
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.832734
say N » 6 say
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
Design of Rebars For Short Span (Positive Moment) Design of Rebars
+Mu = 8.90526 KN·m +Mu
Rn = Mu/øbd2 Rn
= 1.80693
r = r

= 0.006845
rmin = rmax = rmin

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN r
rmin = 1.4/fy rmin
= 0.005091
r = 0.006845 \use r
ASTEEL = 506.5507 ASTEEL
Use ø = 12 mm Use ø
ABAR = 113.0973 mm 2
ABAR
N = 4.478892 N
N » 5 say N
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B
 For Long Span (Positive Moment)
= 12.26745 KN·m
= Mu/øbd2
= 1.76014
=

= 0.006661
= rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
= 1.4/fy
= 0.005091
= 0.006661
= 492.8775
= 12 mm
= 113.0973 mm2
= 4.357994
» 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
 ­Mu = (Ca)(wu)(s2)
= 6.90900 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 9.42233 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 5.18175 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 7.13813 KN·m

DESIGN OF TWO-WAY SLAB (SLAB 7)-FLOOR LEVEL 3 and 4

SLAB 7- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Assembly Areas 4.8 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 and Auditorium= DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 12.18 Kpa
CASE 2 using ACI Method 2
 = 0.0050909
\use r = 0.0052599
ASTEEL = 389.23114
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.4415589
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 290.566 = 300
THEREFORE USE SPACING = 290.566 mm
SAY SPACING = 290 mm

NEGATIVE MOMENT (KN·m)

SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 8.20628 4.02854
LONG 10.11245 5.17955

SPAN POSITIVE MOMENT (KN·m)

SHORT 6.11741
LONG 7.64600
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 8.20628 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 1.66510
r

= 0.0062865
rmin = rmax =

= 0.004776 = 0.037292
 = 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)

-Mu = = 4.02854 KN·m
Rn = Mu/øbd2
= 0.81741
r =

= 0.003026
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
 = 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 10.11245 KN·m

Rn = Mu/øbd2
= 1.45094
r =

= 0.00545
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00545
ASTEEL = 403.3173
Use ø = 12 mm
ABAR = 113.0973 mm2
 = 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 5.17955 KN·m

Rn = Mu/øbd2
= 0.74316
r =

= 0.002747
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
 ­Mu = (Ca)(wu)(s2)
= 11.87368 KN·m
2.2)LONG SPAN (Continuous Edge) Cb= 0.033
­Mu = (Cb)(wu)(L2)
= 16.19303 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, C a= 0.03
+Mu = (Ca)(wu)(S2)
= 8.90526 KN·m
2.) LONG SPAN, Cb= 0.025
+Mu = (Cb)(wu)(L2)
12.26745 KN·m

Design of Rebars For Short Span (Positive Moment)

+Mu = 6.11741 KN·m

Rn = Mu/øbd2
= 1.24126
r =

= 0.00464
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
 = 0.005091
\use r = 0.009264
ASTEEL = 685.5247
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 6.061369
say N » 7
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 164.9792 = 300
THEREFORE USE SPACING = 164.9792 mm
SAY SPACING = 160 mm

Design of Rebars For Long Span (Positive Moment)

+Mu = 7.64600 KN·m

Rn = Mu/øbd2
= 1.09705
r =

= 0.004087
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
Use ø = 12 mm
ABAR = 113.0973 mm2
 = 171.4462 = 300

THEREFORE USE SPAC = 171.4462 mm

SAY SPACI = 170 mm
 = 223.2695 = 300

THEREFORE USE SPACIN = 223.2695 mm THEREFORE USE SPAC

SAY SPACING = 220 mm
 = 229.4634 = 300

THEREFORE USE SPAC = 229.4634 mm

SAY SPACI = 220 mm
 A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s )2

= 8.20628 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.027
­Mu = (Ca)(wu)(s2)
= 4.02854 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L2)
= 10.11245 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L2)
= 5.17955 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 6.11741 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L ) 2

= 7.64600 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 8)-FLOOR LEVEL 3
SLAB 8- CASE 2
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Library (Reading Rm.) 2.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 Library (Stack Rm.) 7.2 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.75 Wu=Ultimate Load
 BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0062865
ASTEEL = 465.2038
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 4.1133047
say N » 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 243.11353 = 300
THEREFORE USE SPACING = 243.11353 mm
SAY SPACING = 243 mm
SAY SPACING = 240 mm

NEGATIVE MOMENT (KN·m)

SPAN CONTINUOUS EDGE DISCONTINUOUS EDGE
SHORT 13.91968 6.83330
LONG 17.15297 8.78567

SPAN POSITIVE MOMENT (KN·m)

SHORT 10.37649
LONG 12.96932
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 13.91968 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 2.82438
r

= 0.0109767
rmin = rmax =
 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

Design of Rebars For Short Span (Discontinuous Edge-Negative Moment)

-Mu = = 6.83330 KN·m
Rn = Mu/øbd2
= 1.38651
r =

= 0.0052
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.0052
ASTEEL = 384.8277
Use ø = 12 mm
 N = 3.566108
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 280.4177 = 300

THEREFORE USE SPACING = 280.4177 mm

SAY SPACING = 280 mm
SAY SPACING = 280 mm

``

Design of Rebars For Long Span (Continuous Edge-Negative Moment)

­Mu = 17.15297 KN·m

Rn = Mu/øbd2
= 2.46111
r =

= 0.009476
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.009476
ASTEEL = 701.2063
 N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``

Design of Rebars For Long Span (Discontinuous Edge-Negative Moment)

­Mu = 8.78567 KN·m

Rn = Mu/øbd2
= 1.26057
r =

= 0.004714
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
 N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``

Design of Rebars For Short Span (Positive Moment)

+Mu = 10.37649 KN·m

Rn = Mu/øbd2
= 2.10545
r =

= 0.008035
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008035
ASTEEL = 594.5546
 N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``

Design of Rebars For Long Span (Positive Moment)

+Mu = 12.96932 KN·m

Rn = Mu/øbd2
= 1.86084
r =

= 0.007059
rmin = rmax =
DESIGN LOADS:
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.007059
ASTEEL = 522.3455
 DESIGN OF TWO-WAY SLAB (SLAB 8)-FLOOR LEVEL RD
SLAB 8- CASE 2 SPAN
DESIGN DATA hmin=P/180 Span (m) SHORT
F'c 27.6 Mpa hmin 0.08889 S 3.5 LONG
fy 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø 12 mm d aveL 88
Conc. Cove 20 mm
Design of Rebars
DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Soil 12.28 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0.07 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
\ WTOTAL DL 3.82 Wu=Ultimate Load
 NEGATIVE MOMENT (KN·m) Design of Rebars
CONTINUOUS EDGE DISCONTINUOUS EDGE -Mu =
16.32631 8.01473 Rn
20.11862 10.30466
r
SPAN POSITIVE MOMENT (KN·m)
SHORT 12.17052
LONG 15.21164 rmin
Design of Rebars For Short Span (Continuous Edge-Negative Moment)
­Mu = 16.32631 KN·m
Rn = Mu/øbd2 BUT SHOULD NOT BE LESS THAN r
= 3.31270 rmin
r
\use r
= 0.013043 ASTEEL
rmin = rmax = Use ø
 For Short Span (Discontinuous Edge-Negative Moment) Design of Rebars For Long Span (Continuous
= 8.01473 KN·m
= Mu/øbd2 ­Mu =
= 1.62623 Rn =
= =
r =
= 0.006134
= rmax = =
rmin =
= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin =
= 1.4/fy BUT SHOULD NOT BE LESS THAN rmin
= 0.005091 rmin =
= 0.006134 =
= 453.9245 \use r =
= 12 mm ASTEEL =
 For Long Span (Continuous Edge-Negative Moment) Design of Rebars For Long Span (Discontinuous Edge-N

20.11862 KN·m ­Mu = 10.30466

Mu/øbd2 Rn = Mu/øbd2
2.88662 = 1.47851
r =

0.011237 = 0.005557
rmax = rmin =

0.004776 = 0.037292 = 0.004776

OULD NOT BE LESS THAN rmin BUT SHOULD NOT BE LESS THAN rmin
1.4/fy rmin = 1.4/fy
0.005091 = 0.005091
0.011237 \use r = 0.005557
831.5287 ASTEEL = 411.2503
For Long Span (Discontinuous Edge-Negative Moment) Design of Rebars For Short Span (Positive Moment)

KN·m +Mu = 12.17052 KN·m

Rn = Mu/øbd2
= 2.46947
r =

= 0.00951
rmax = rmin = rmax

= 0.037292 = 0.004776
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.00951
ASTEEL = 703.7361
rt Span (Positive Moment) Design of Rebars For Long Span (Positive Moment)

+Mu = 15.21164 KN·m

Rn = Mu/øbd2
= 2.18257
r =

= 0.008345
= rmin = rmax =

= 0.037292 = 0.004776 =
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.008345
ASTEEL = 617.5115
0.037292
 W U= 20.66 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.055
­Mu = (Ca)(wu)(s2)
= 13.91968 KN·m
1.2)SHORT SPAN (Discontinuous Edge) Ca = 0.027
­Mu = (Ca)(wu)(s2)
= 6.83330 KN·m
` 2.1)LONG SPAN (Continuous Edge) C b= 0.041
­Mu = (Cb)(wu)(L )
2

= 17.15297 KN·m
2.2)LONG SPAN (Discontinuous Edge) C b= 0.021
­Mu = (Cb)(wu)(L2)
= 8.78567 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.041
+Mu = (Ca)(wu)(S2)
= 10.37649 KN·m
2.) LONG SPAN, C b= 0.031
+Mu = (Cb)(wu)(L2)
= 12.96932 KN·m
DESIGN OF TWO-WAY SLAB (SLAB 8)-FLOOR LEVEL 2, 4, and 5
SLAB 8- CASE 1
DESIGN DATA hmin=P/180 Span (m)
F'c = 27.6 Mpa hmin 0.08889 S 3.5
fy = 275 Mpa use 100 L 4.5
g conc. = 24 KN/m3 d aveS 74 0.778
Bar Ø = 12 mm d aveL 88
Conc. Cover = 20 mm

DESIGN LOADS:
DEAD LOADS (KPa) LIVE LOADS (KPa)
WCEILING 0.2 Classroom= 1.9 S/L is greater than 0.5 therefore
WFLOOR FINISH 1.15 DESIGN AS TWO-WAY SLAB
WWATER PROOFING 0 USING NSCP 2010
WSLAB 2.4 WU=1.2DL+1.6LL
 = 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0109767
ASTEEL = 812.27222
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 7.1820633
say N » 8
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 139.23575 = 300
THEREFORE USE SPACING = 139.23575 mm
SAY SPACING = 139 mm
SAY SPACING = 130 mm

SPAN NEGATIVE MOMENT (KN·m)

SHORT 3.69460
LONG 5.03861

SPAN POSITIVE MOMENT (KN·m)

SHORT 2.77095
LONG 3.81713

Design of Rebars For Short Span (Negative Moment)

­Mu = 3.69460 KN·m
Rn = Mu/øbd2
eater than 0.5 therefore = 0.74966
r

= 0.002771
 ABAR = 113.0973 mm2
N = 3.402624
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 293.8909 = 300

THEREFORE USE SPACING = 293.8909 mm

SAY SPACING = 290 mm

Design of Rebars For Long Span (Negative Moment)

-Mu = = 5.03861 KN·m
Rn = Mu/øbd2
= 0.72294
r =

= 0.002671
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 6.200025
say N » 7
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 161.2897 = 300

THEREFORE USE SPACING = 161.2897 mm

SAY SPACING = 161 mm
SAY SPACING = 160 mm

``

Design of Rebars For Short Span (Positive Moment)

+Mu = 2.77095 KN·m
Rn = Mu/øbd2
= 0.56224
r =

= 0.00207
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm

``

Design of Rebars For Long Span (Positive Moment)

+Mu = 3.81713 KN·m
Rn = Mu/øbd2
= 0.54768
r =

= 0.002015
rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.005091
\use r = 0.005091
ASTEEL = 376.7273
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.257017
say N » 6
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 190.2219 = 300

THEREFORE USE SPACING = 190.2219 mm

SAY SPACING = 190 mm

``
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 4.618548
say N » 5
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 216.5183 = 300

THEREFORE USE SPACING = 216.5183 mm

SAY SPACING = 210 mm

``
 WU = 24.232 Kpa
CASE 2 using ACI Method 2
A. FOR NEGATIVE MOMENTS BUT SHOULD NOT BE LESS
1.1)SHORT SPAN (Continuous Ed C a= 0.055
­Mu = (Ca)(wu)(s2)
= 16.32631 KN·m \use
1.2)SHORT SPAN (Discontinuous C a= 0.027
­Mu = (Ca)(wu)(s2)
= 8.01473 KN·m
` 2.1)LONG SPAN (Continuous Edg Cb= 0.041
­Mu = (Cb)(wu)(L )2
say
= 20.11862 KN·m
2.2)LONG SPAN (Discontinuous E Cb= 0.021
­Mu = (Cb)(wu)(L2)
= 10.30466 KN·m
B. FOR POSITIVE MOMENTS
1.)
SHORT SPAN, C a= 0.041
+Mu = (Ca)(wu)(S2)
= 12.17052 KN·m
2.)LONG SPAN, Cb= 0.031
+Mu =(Cb)(wu)(L2)
15.21164 KN·m
 ABAR
= 0.004776 = 0.037292 N
BUT SHOULD NOT BE LESS THAN rmin say N
rmin = 1.4/fy SPACING, S = (A B
= 0.005091
r = 0.013043
ASTEEL = 965.2048 THEREFORE USE SPAC
Use ø = 12 mm
ABAR = 113.0973 mm2
N = 8.534284
N » 9
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 117.1744 = 300
THEREFORE USE SPACIN = 117.1744 mm
SAY SPACING = 117 mm
SAY SPACING = 110 mm
 = 113.0973 mm2 Use ø =
= 4.013574 ABAR =
» 5 N =
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h say N »
= 249.1545 = 300 SPACING, S = (A B/AS)x1000
=
THEREFORE USE SPAC = 249.1545 mm
SAY SPACI = 240 mm THEREFORE USE SPAC
SAY SPACI
SAY SPACI
 12 mm Use ø = 12
113.0973 mm2 ABAR = 113.0973
7.352328 N = 3.636251
8 say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
136.0113 = 300 = 275.0085

= 136.0113 mm THEREFORE USE SPAC =

= 136 mm SAY SPACI =
= 130 mm

``
 mm Use ø = 12 mm
mm2 ABAR = 113.0973 mm2
N = 6.222394
say N » 7
G, S = (A B/AS)x1000 MAX SPACING = 3h SPACING, S = (A B/AS)x1000
= 300 = 160.7099

275.0085 mm THEREFORE USE SPAC = 160.7099

275 mm SAY SPACI = 160

``
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 5.46
say N » 6
MAX SPACING = 3h SPACING, S = (A B/AS)x1000 MAX SPACING =
= 300 = 183.1502

mm THEREFORE USE SPAC = 183.1502 mm

mm SAY SPACI = 180 mm

``
MAX SPACING = 3h
= 300

``
\ WTOTAL DL 3.75 Wu=Ultimate Load
W U= 7.54 Kpa
CASE 1 using ACI Method 2
A. FOR NEGATIVE MOMENTS
1.1)SHORT SPAN (Continuous Edge) Ca = 0.04
­Mu = (Ca)(wu)(s2)
= 3.69460 KN·m
2.2)LONG SPAN (Continuous Edge) C b= 0.033
­Mu = (Cb)(wu)(L2)
= 5.03861 KN·m
B. FOR POSITIVE MOMENTS
1.) SHORT SPAN, Ca = 0.03
+Mu = (Ca)(wu)(S2)
= 2.77095 KN·m
2.) LONG SPAN, C b= 0.025
+Mu = (Cb)(wu)(L2)
= 3.81713 KN·m
 rmin = rmax =

= 0.004776 = 0.037292
BUT SHOULD NOT BE LESS THAN rmin
rmin = 1.4/fy
= 0.0050909
\use r = 0.0050909
ASTEEL = 376.72727
Use ø = 12 mm
ABAR = 113.09734 mm2
N = 3.3310004
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.21011 = 300
THEREFORE USE SPACING = 300 mm
SAY SPACING = 300 mm
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm
 Use ø = 12 mm
ABAR = 113.0973 mm2
N = 3.331
say N » 4
SPACING, S = (A B/AS)x1000 MAX SPACING = 3h
= 300.2101 = 300

THEREFORE USE SPACING = 300 mm

SAY SPACING = 300 mm