Scribd
Upload
81 views12 pages

UC501 IPPBX Quick Start

The document provides quick start instructions for setting up and accessing the OpenVox UC501 IPPBX, including: - Downloading the latest datasheet and manual from the OpenVox website - Checking that all components are included in the package - Installing FXO and FXS modules into the chassis - Connecting the LAN port, power, analog phones and PSTN line - Logging into the administrator interface using the default IP and credentials

Uploaded by

issam hmirou
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
81 views12 pages

UC501 IPPBX Quick Start

The document provides quick start instructions for setting up and accessing the OpenVox UC501 IPPBX, including: - Downloading the latest datasheet and manual from the OpenVox website - Checking that all components are included in the package - Installing FXO and FXS modules into the chassis - Connecting the LAN port, power, analog phones and PSTN line - Logging into the administrator interface using the default IP and credentials

Uploaded by

issam hmirou
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

OpenVox Communication Co Ltd

UC501 IPPBX Quick Start


Information

Access to data
Please visit www.openvox.cn, and select the product model, get the

latest support information, including datasheet and user manual.

Technical Support
For help, contact OpenVox Communication Co., Ltd. Technical Support:

Email: [email protected]

Tel: +86-755-66630978 , +86-755-82535461

Fax: +86-755-83823074
UC501 Quick Start

Packing Details
After unpacking, check if the contents are complete. If there are any

omissions, please contact your dealer.

⚫ UC501 x 1

⚫ Network Connection x 1

⚫ Power Adapter x 1

⚫ Rubber Mat x 1

⚫ Certification x 1

⚫ Quick Start x 1

Hardware Specification

A. Front

①Power Indicator ②System Indicator ③Reset Button ④

Microphone ⑤Speaker ⑥TF Card Slot ⑦USB Interface ⑧WAN

Port ⑨LAN Port ⑩FXO/FXS Interface


LED Indicator Color Status

① Power Indicator Always Green Supply Power

② System Indicator Green and Flash(1s) Work Normally

Red and Flash(1s) Normal


⑩Module Indicators
Always Red Connected
(FXO)
Red and Flash(0.1s) Communicating

⑩Module Indicators Always Green Normal

(FXS) Green and Flash(0.1s) Communicating

During initialization, all LED indicators will flash successively

B. Back

① Power Input: DC 12V


Install Module

After confirming the components are complete, start installing modules.

1. Unscrew the screws on both sides of the device.

2. Remove the upper casing in the direction shown in picture.


3. The UC501 series of products adopt modular design and are divided

into new and old modules.

Below is the top view of the inside of the chassis, and the right side is the

module installation area. There are four areas where you can install

modules.

（1）For new module：users can choose any combination of the following

three modules.

①FXS-200

②FXO-200

③FXOS-200
Remove the screw and install the module.

（2）For old module：The upper area is for the FXO-100/FXS-100 module

and the lower area is for the FXO-400/FXS-400 module. It should be noted

that the module cannot be installed on the left or right side at the same

time, only supports ①+②, ③+④, ①+④, ②+③.Users can choose two

module accessories to customize.

• FXO-100+FXO-100

• FXO-100+FXS-100

• FXO-100+FXO-400

• FXO-100+FXS-400

• FXS-100+FXS-100

• FXS-100+FXO-400

• FXS-100+FXS-400
• FXO-400+FXO-400

• FXO-400+FXS-400

Remove the screw and install the module（②+③）.


4. After installing the module, insert the chassis vertically as the picture

shows, fasten it to the upper case, and then tighten the screws.
Cable Connection

Please use the dedicated power adapter. Otherwise, the failure or damage

caused by other power adapters is not covered by the warranty.

① Connect the LAN port to the LAN switch using a network cable.

② Use the dedicated power cable and turn on the power, the UC501

system starts, and the power indicator is green.

③ Connect the FXS connector to the analog phone using a telephone line.

④ Use a telephone line to connect the FXO interface to the PSTN line or

the internal line of legacy PBX.

Note: Please connect the PSTN line or analog phone to the corresponding

interface according to the color of the interface indicator.


Login administrator interface

1. Connect the computer to the same network with the UC501 device;

2. Open a web browser and enter the default IP address of UC501:

172.16.101.1;

3. Use the default username(admin) and password(admin) to log in to the

administrator interface.

You might also like