TEMS™ Investigation 22.3.

6 Release Note
1 About This Release
© Infovista 2022. All rights reserved.

TEMS is a trademark of Infovista. All other trademarks are the property of their respective holders. Apple, the
Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.

2 Important Information

2.1 Disabling Wi-Fi for Mobile Network Testing

Before using a device for mobile network data service testing, be sure to turn off Wi-Fi on the device. If Wi-Fi is
enabled, the device may run data transfers over Wi-Fi rather than over the mobile network it is camping on (even
if a correct APN has been entered).

2.2 Keeping Down Logfile Size When Running Data Services on Qualcomm and
Samsung Chipset Based Devices

This section applies to Qualcomm chipset-based and Samsung chipset-based devices, unless otherwise stated.

It is strongly recommended to follow these steps, since otherwise the PC processing load will become
excessive.

• When testing data services only, use a Log Configuration activity with the option “Optimized for Data KPI
Reports” selected.

• For Qualcomm chipset devices, you can alternatively either disable the DPL log (0x11EB) or set USB
mode to RNDIS+DM+MODEM. Be aware that in RNDIS+DM+MODEM mode it is not possible to apply
certain control functions such as RAT and band lock. In TEMS™ Investigation the DPL log is by default
turned off in RNDIS+DM+MODEM mode.

• When testing both VoLTE and data services concurrently, use a Log Configuration script activity with the
option “Optimized for Voice/Data KPI Reports” selected.

www.infovista.com | 1
3 TEMS™ Investigation 22.3.6

3.1 Corrected bugs

• 00368890 NR SA Primary/secondary cell measurements

• 00372041 TI 22.3.3 5G NAS Message Decoding
• 00378129 Missing NR SINR for second cell
• 00381432 PCTEL IBFlex missing NR SIB1 reports

4 TEMS™ Investigation 22.3.5

4.1 Corrected bugs

• 00378150 NR wrong values for RSRP, RSRQ and SINR on 2 cells

• 00360054 Quectel BC95G - wrong LTE band reported
• 00362823 Too low throughput values
• 00368890 NR SA Primary/secondary cell measurements
• 00369427 Wrong LTE CA Info
• 00373825 Abnormal value of PDSCH Physical Throughput

5 TEMS™ Investigation 22.3.4

5.1 Corrected bugs

• 00352420 TI 22.3 decode wrong UE mode when connect Mate 30 in 5G SA

• 00353754 Cell Distance I.E not available in 5G SA mode
• 00362464 OPPO Find X2 getting Disconnected with TEMS once camped on ESS
• 00362585 LTE PDCP vs LTE PDSCH DL issue, same for NR
• 00364594 Timestamp between Devices Call Events Are Wrong For VoWifi Test
• 00367804 Reference Device (X60) incompatibility with TEMS 22.3.3

6 TEMS™ Investigation 22.3.3

6.1 Corrected bugs

• 00359244: MTP X60 on Android 11 does not detect in TI 22.3.2

• 00357410: TP 22.2.1 S20 FE - 5G measurements disappear during TDAB import
• 00359922: iPhone 11 on iOS 13.6/14.4 fails to be detected by TI 22.3.2
• 00345593: Implementation of CR 121 follow up
• 00359281: Samsung S21 SM-G998U Missing KPI
• 00354922: High share of unsustainable calls for all clients - silent sample
• 00361562: TI can't decode AGC Sub Packet version 4
• 00354541: RDE export not valid XML for gOTT
• 00359798: LTE PDCP throughput is not coming in TI v22.3 [
• 00361366: LTE PDSCH/PDCP Throughput not reported for SDX60 device

www.infovista.com | 2
 • 00361186: RFA-24979: 5G UE Transmit Power missing from GS21 report
• 00360931: TEMS Investigation does not open logs
• 00360975: Filemark event icon not possible to display on the mapview

7 TEMS™ Investigation 22.3.2

7.1 New TEMS Devices

7.1.1 Sony Xperia 1 Mark 2 (XQ-AT42)

This Sony Xperia 1 Mark II is a Qualcomm SD865 chipset-based smartphone running Android 10 aimed at the
Japanese market. It is introduced with TEMS firmware, which makes it ready for testing of existing and new
networks with focus on data service testing.

Specifications1:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM)

• Lock on Band (LTE/WCDMA/GSM)

• Lock on EARFCN+PCI2

• Lock on UARFCN

• Frequency bands:

• 5G: Sub6G Bands: n1, n3, n28, n77, n78

• 4G: FDD-LTE Bands: 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 19, 20, 25, 26, 28, 29, 32, 34, 38, 39, 40, 41, 46, 66

• 3G: WCDMA Bands: 1, 2, 4, 5, 6, 8, 19

• 2G: GSM Bands: 850, 900, 1800, 1900

• Throughput capabilities:

• NR Non-Standalone and Standalone mode

• LTE Category 19/13 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• LTE Carrier Aggregation DL 6CA/UL 2CA

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• MIMO

• VoLTE/VoWiFi

• Audio Quality Measurements using the POLQA or sQLEAR algorithm.

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

www.infovista.com | 3
• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• TEMS Connect License: Qualcomm N

1 The device radio settings are reconfigured every time a new SIM card is inserted to the phone, therefore, you
need to test in the specific network to obtain a correct value for band support and capabilities.
2 Both EARFCN and PCI must be set.

7.1.2 Samsung Galaxy Note20 Ultra (SM-N9860)

The Galaxy Note 20 Ultra 5G is an Android 10 smartphone based on a Qualcomm chipset and aimed at the
Chinese market. The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s
DL and 316 Mbit/s UL) and 5G throughput up to 5+ Gbit/s.

Specifications1:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B14(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B29(700),
B30(2300), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900),B40(2300), B41(2500), B46(5200)

• 5G: N1 (FDD 2100 MHz), N3 (FDD 1800 MHz), N5 (FDD 850 MHz), N7 (FDD 2600 MHz), N8 (FDD 900
MHz), N28 (FDD 700 MHz), N40 (TDD 2300 MHz), N77 (TDD 3700 MHz), N78 (TDD 3500 MHz)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

www.infovista.com | 4
 • LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• TEMS Connect License:

• Qualcomm N
1 Depending on network and SIM. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

7.2 Corrected Bugs

• 358717: Connecting S20+ and S20 Ultra 5G devices with Android 11

• 358929: MTP X60 Device TEMS Connectivity

• 358972: Commercial S20 5G SM-G981B on Android 11 fails to be activated.

8 TEMS™ Investigation 22.3.1

8.1 New Connectable Devices

8.1.1 Samsung Galaxy S21 series

The brand-new Samsung Galaxy S21 series is added as connectable to TEMS Investigation which makes it
possible to perform testing with the latest devices out there. It is based on a Qualcomm Snapdragon 888 or
Samsung Exynos 2100 chipset depending on market, both which offers 5G connectivity as well as LTE 7CA and
Cat. 20 support.

From TEMS Investigation, it is possible to install on-device software enabling Ping, HTTP (file) and iPerf tests to
be performed directly on the device. Aside that, TEMS Investigation can control voice calls and data transfers
from the device.

So, as soon as you get hold of a Samsung S21, just connect it to your TEMS Investigation and start your test!

www.infovista.com | 5
Supported versions:

• Samsung Galaxy S21: SM-G991B/U/U1/W/0

• Samsung Galaxy S21+: SM-G996B/U/U1/W/0

• Samsung Galaxy S21 Ultra: SM-G998B/U/U1/W/0

Specifications:

• 5G: 5G Non-Standalone (NSA), Standalone (SA), Sub6 / mmWave

• LTE: Enhanced 4x4 MIMO, Up to 7CA, LTE Cat.20Up to 2.0Gbps Download / Up to 200Mbps Upload

• Wi-Fi: Wi-Fi 802.11 a/b/g/n/ac/ax 2.4G+5GHz, HE80, MIMO, 1024-QAM. Up to 1.2Gbps Download / Up to
1.2Gbps Upload

• Chipset: Exynos 2100 or Qualcomm SM8350 Snapdragon 888 depending on market

• Operating System: Android 11

• TEMS Connect License: Qualcomm O or Samsung H depending on market.

8.1.2 Qualcomm X60 MTP

The Mobile Testing Platform with the new 5G modem from Qualcomm, X60, can now be connected to TEMS
Investigation and used for network testing.

Specifications:

• Operating System: Android 10

• TEMS Connect License: Qualcomm O

8.1.3 LG Wing LM-F100TM

The LG Wing offers a swivel screen that gives users a new experience of a smartphone. It is based on a
Qualcomm chipset and offers 5G connectivity. In TEMS Investigation, it is introduced as a connectable device
with basic functionality.

Specifications:

• Operating system: Android 10

• Chipset: Snapdragon 765G (5G)

• TEMS Connect License: Qualcomm O

8.2 New TEMS Devices

8.2.1 Samsung Galaxy Note20 Ultra 5G (SM-N986B)

The Galaxy Note20 Ultra 5G is an Android 10 smartphone based on a Samsung chipset. The device is capable of
measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s UL and 5G throughput
up to 5+ Gbit/s)2.

www.infovista.com | 6
Specifications1:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B32(1500),
B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500)

• 5G FDD Sub6: N1(2100), N3(1800), N5(850), N7(2600), N8(900), N28(700)

• 5G TDD Sub6: N40(2300), N77(3700), N78(3500)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

www.infovista.com | 7
• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Samsung Exynos 990 Octa-Core (2x2.73 GHz Mongoose M5 & 2x2.60 GHz Cortex-A76 & 4x2.0 GHz
Cortex-A55)

• TEMS Investigation/Paragon Connect License:

• Samsung G
1 Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.
2 Audio Quality Measurements are not available on the SM-N988B.

8.3 New Features

8.3.1 iPhone on-device testing (HTTP file/ Ping/ IPerf)

It is now possible to use on-device software on Apple iPhones (HTTP UL/DL (file), Ping (ICMP) and iPerf v3.9)
when performing network testing with TEMS Investigation. This gives users the same measurements as when
using commercial Android devices and broadens the use case for Apple iPhone with TEMS Investigation.

Available KPIs:

• HTTP:
• HTTP Throughput per second DL (kbit/s)
• HTTP Average Throughput DL (kbit/s)
• HTTP Session Failure Ratio UL/DL (%)
• HTTP Received (b)
• HTTP Transfer Time (s)
• HTTP Session Success
• Application Layer DL Throughput (kbit/s)
• Application Layer Received (b)
• Ping: (events)
• Roundtrip time (ms)
• Ping Start, End and Error
• iPerf:
• TCP/UDP Average Throughput UL/DL (kbit/s)
• TCP/UDP Sent/Received (b)
• TCP/UDP Throughput UL/DL (kbit/s)
• TCP/UDP Transfer Time UL/DL (s)
• UDP Jitter DL (ms)
• UDP Packet Loss DL (%)

8.4 Corrected bugs

• TEMS Paragon4.3 ODM HTTP Post End -> System.ArgumentException

www.infovista.com | 8
• 100271: Xiaomi Mi 10T Pro 5G - M2007J3SG Detection issue

• 00343663: Raw to Refined by routeutility

• 00348372: BTH5 firmware and SSB Beam / CQI not reported

• 00348895: Events having incorrect Time stamp

• 00350631: Strange drop event - Tems Investigation 22.2.1

• 00352081: Problem with LTE TTI allocation in Exynos chipset

• 00352976: Clarification on serving cell count IE

• 00355653: Urgent - Logs are not parsing in Tems 22.3 version

• 00349204: UL256QAM Modulation Not Showing on TEMS for LTE

• 00349215: RLC DL/UL Parameters Missing

• 00351592: Problems with 3rd/4th Carrier Aggregation IEs

• 00351803: TI_ Application Layer & scale definition on the charts

• 00353730: R&S TSMW scanner connection issue on TI 22.3

• 00348207: File UL status “Could not push the file to the device” TEMS™ Investigation 22.3

8.5 New TEMS Devices

8.5.1 Samsung Galaxy S20 FE 5G (SM-G781B)

The Galaxy S20 FE 5G is an Android 10 smartphone based on a Qualcomm chipset. The device is capable of
measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s UL) and 5G
throughput up to 5+ Gbit/s. The Samsung Galaxy S20 FE 5G is tuned for Audio Quality Testing using the
sQLEAR or POLQA algorithm.

Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

www.infovista.com | 9
• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B20(800), B26(850), B28(700), B32(1500), B66(AWS-3)

• 4G TDD LTE: B38(2600), B40(2300), B41(2500)

• 5G FDD Sub6: N1(2100), N3(1800), N5(850), N7(2600), N8(900), N28(700)

• 5G TDD Sub6: N40(2300), N41(2500), N78(3500)

• Throughput capabilities:

• NR Non-Standalone/Standalone

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License:

• Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

8.5.2 Xiaomi Mi 10T Pro (M2007J3SG and M2007J3SY)

Parts of the Xiaomi Mi 10T Pro range is introduced in TEMS Investigation 22.3, including two new phones from
the Chinese company, to complement the Mi 10 line from the beginning of the year. It has a mid-range price but

www.infovista.com | 10
some advanced specs, namely a high-res main camera and a flagship processor, with corners cut in other areas
to achieve the price. With TEMS Investigation, both models are prepared for advanced testing of data services
and voice calls.

Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• Lock on Cell (EARFCN or UARFCN)

• Audio Quality Measurements

• POLQA

• sQLEAR

• Frequency bands:

• 5G: n1/n3/n7/n8/n20/n28/n38/n41/n77/n78

• 4G: LTE FDD: B1/2/3/4/5/7/8/20/28/32

• 4G: LTE TDD: B38/40/41

• 3G: WCDMA:B1/2/4/5/8

• 2G: GSM: B2/3/5/8

• Throughput capabilities:

• NR Non-Standalone and Standalone mode

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

8.6 New Connectable Devices

8.6.1 Samsung Galaxy S20 FE 5G SM-G781U/V/W

The Galaxy S20 FE 5G is an Android 10 smartphone based on a Qualcomm chipset. The device is capable of
measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s UL) and 5G

www.infovista.com | 11
throughput up to 5+ Gbit/s. In TEMS Investigation 22.3, three versions are added as connectable and can
therefore be used for basic data service and call setup testing.

Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B20(800), B26(850), B28(700), B32(1500), B66(AWS-3)

• 4G TDD LTE: B38(2600), B40(2300), B41(2500)

• 5G FDD Sub6: N1(2100), N3(1800), N5(850), N7(2600), N8(900), N28(700)

• 5G TDD Sub6: N40(2300), N41(2500), N78(3500)

• Throughput capabilities:

• NR Non-Standalone/Standalone

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License:

• Qualcomm N

www.infovista.com | 12
*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

8.6.2 Samsung Galaxy Z Fold2 (SM-F916B and SM-F916U/U1)

The Galaxy Z Fold2 is an Android 10 smartphone based on a Qualcomm chipset with a foldable screen. The
device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s
UL) and 5G throughput up to 5+ Gbit/s. In TEMS Investigation 22.3, it is added as connectable and can therefore
be used for basic data service and call setup testing.

Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Frequency bands:

• SM-F916B:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500)

• 5G FDD Sub6: N1(2100), N3(1800), N5(850), N7(2600), N8(900), N28(700)

• 5G TDD Sub6: N40(2300), N41(2500), N77(3700), N78(3500)

• SM-F916U:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• 4G FDD LTE: B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700), B13(700),
B18(800), B19(800), B20(800), B26(850), B28(700), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500), B46(5200), B48(3600)

• Throughput capabilities:

• NR Non-Standalone/Standalone

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

www.infovista.com | 13
 • LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Qualcomm SD865+ Octa-core (1x3.09 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License:

• Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

8.7 New features

8.7.1 ODM HTTP PUT testing

New script setting allows usage of HTTP PUT when running HTTP upload. All Messages, Events and Information
Elements are the same with HTTP POST.

Note: This feature requires ODM version 1.171 which is planned for release on Dec. 14 th 2020.

8.7.2 PCTEL MXflex: Added Channel Matrix for 2x2 and 4x2 MIMO
User is now able to perform LTE Signal Scan with Channel Matrix for 2x2 and 4x2 MIMO with 2x2 channel matrix
measurement license option (MXflex only).

8.7.3 PCTEL Scanning - Cable Loss during NR mmWave Scanning

Two parameters were added to NR Signal Scan so that users can enter the antenna gain & cable loss for
mmWave antennas to compensate for each scanner measurement.

8.7.4 PCTEL: Added SIB24 and SIB25 support in eTOPN scan

PCTEL SIB24, SIB25 has been added in LTE Signal Scan when "System Information" setting is enabled. Network
which enabled with the above SIB messages will be decoded in L3 message window.

www.infovista.com | 14
8.7.5 Rohde & Schwarz: Add DSS support
DSS (Dynamic Shared Spectrum) tolerant mode has been added as a new parameter in LTE Signal Scan on
TSME, TSME6 and TSMW scanners. DSS tolerant mode ensures correct LTE measurements in case the LTE
carrier frequency is being used for DSS. The mode delays measurement results until the SIB2 has been decoded
and configures the LTE scanner not to measure on subframes which are not used for LTE.

Note: ViCom 20.2 or later is required to use DSS tolerant mode.

8.7.6 PCTEL Scanner information optimized when used as preferred GPS

Reduced log file size and reduced load time in some cases when using PCTEL Scanner as preferred GPS.

8.7.7 PCTEL MX: Spectrum Scan on MXflex, to set range of frequency

Added an equipment property to set the frequency range of different scanner antenna ports. It is applicable to
MXflex, HBflex and IBflex. User can set the minimum/maximum frequency of each supported antenna port.

8.7.8 License verification enhancements at start-up- with detailed error information

TEMS Investigation and TEMS Paragon will now provide better information what to do when it has not had
contact with a license server for more than 5 days and cannot start.

8.7.9 Add HTTP Data Transfer Cutoff Ratio Method A and B

Added KPIs for HTTP Data Transfer Cutoff Ratio Method A and Method B. Previously the methods could not be
distinguished between. This is a requirement for complying with ETSI TS 102 250-2 V2.6.1 (2017-10) section
6.8.8.

8.7.10 Warning when "On Failure" equals "Continue script execution

Default error handling for scripts is now “Stop Script Execution”, changed from “Continue Script Execution”.
Additionally, when a script is validated in Service Script Control Designer it will warn the user when the old
handling is applied.

8.7.11 Additional IEs Samsung “Serving Cell SS RSRP” and “Serving Cell SSB Beam
RSRP” (similar for RSRQ).
Added Samsung support for the following Information Elements.

• Serving Cell SSB Beam RSRP

• Serving Cell SSB Beam RSRQ
• Serving Cell SSB Beam Index

8.7.12 iPerf: Add Application Layer Throughput for UE Mode

Added application layer Information Elements for

• UL throughput for TCP and UDP UE Mode

• DL throughput for TCP and UDP UE Mode

www.infovista.com | 15
8.7.13 3GPP decoding updates
Updated decoding to latest versions of 5G NAS, LTE RRC and NR RRC.

8.7.14 Vendor report decoding updates

Updated decoding of LTE and NR reports for Samsung and Qualcomm.

8.8 New NR Information Elements / Events

In this release of TEMS Investigation several information elements and events has been added to all three
supported 5G chipsets. All additions are listed below.

8.8.1 Qualcomm
• RACH Preamble Msg1 Event
• RACH Response Msg2 Event
• RACH UE Identification Msg3 Event
• RACH Contention Resolution Msg4 Event

8.8.2 Samsung
• Serving Cell SSB Beam RSRP
• Serving Cell SSB Beam RSRQ
• Serving Cell SSB Beam Index

8.8.3 HiSilicon

• RACH Initial Tx Power

• RACH Current Tx Power
• RACH Number of Transmits
• RACH Latency
• MR-DC DRB CN
• MR-DC DRB EPS Bearer ID
• MR-DC DRB PDU Session ID
• MR-DC DRB PDCP Type
• MR-DC DRB QCI
• MR-DC DRB RLC DL Path
• MR-DC DRB RLC UL Path
• MR-DC DRB Mode
• MR-DC DRB ID
• MR-DC DRB Type
• NR Serving Cell DSS Configured Frequency <1..3>
• NR Serving Cell DSS Configured Band <1..3>
• NR Serving Cell DSS Configured Bandwidth <1..3>
• Inter-System NR Neighbor Cell SS-RSRP
• Inter-System NR Neighbor Cell SS-RSRQ
• Inter-System NR Neighbor Cell SS-SINR

www.infovista.com | 16
 • Inter-System NR Neighbor Cell Identity
• Inter-System NR Neighbor Cell NR-ARFCN
• Inter-System NR Neighbor Cell Best Beam Index

8.9 Corrected bugs

• 345422: Huawei P40 inconsistent Throughput recording/computation

• 341780 VoLTE KPI issue

8.10 Removed Features

No features were removed in this release.

9 TEMS™ Investigation 22.2.1

9.1 New Connectable Devices

9.1.1 Apple iPhone 12, 12 mini, 12 Pro and 12 Pro Max

As soon as the Apple iPhone is available for purchase, it can be used for network testing with TEMS
Investigation. The iPhone 12 is a 5G ready smartphone built on a A14 Bionic chipset and running iOS 14.1. TEMS
Investigation can be used to perform service testing with focus on data throughput1.

Specifications2:

• Frequency bands3:

• 5G NR (Bands n1, n2, n3, n5, n7, n8, n12, n20, n25, n28, n38, n40, n41, n66, n71, n77, n78, n79)

• 5G NR mmWave (Bands n260, n261)

• FDD‑LTE (Bands 1, 2, 3, 4, 5, 7, 8, 12, 13, 14, 17, 18, 19, 20, 21, 25, 26, 28, 29, 30, 32, 66, 71)

• TD‑LTE (Bands 34, 38, 39, 40, 41, 42, 46, 48)

• CDMA EV-DO Rev. A (800, 1900 MHz)

• UMTS/HSPA+/DC‑HSDPA (850, 900, 1700/2100, 1900, 2100 MHz)

• GSM/EDGE (850, 900, 1800, 1900 MHz)

• Throughput capabilities:

• Gigabit LTE with 4x4 MIMO and LAA4

• Wi‑Fi 6 (802.11ax) with 2x2 MIMO

• iOS 14.1

• Chipset: Apple Bionic A14

• TEMS Connect License: Apple B

www.infovista.com | 17
1 Voice calls cannot be automated for VoLTE in this release.
2 Depending on network and SIM-card. The device radio settings can be reconfigured every time a new SIM card
is inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band
support and capabilities.
3 There are regional differences in band support, please refer to https://www.apple.com/iphone/cellular/ for details.

9.2 New TEMS Devices

9.2.1 Samsung Galaxy Note 20 (SM-N981U/W) / Note 20 Ultra (SM-N986B)

The Galaxy Note 20/Note 20 Ultra 5G is an Android 10 smartphone based on a Samsung or Qualcomm chipset.
The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316
Mbit/s UL) and 5G throughput up to 5+ Gbit/s.

Specifications1:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 3G UMTS: B1(2100), B2(1900), B4(AWS), B5(850), B8(900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B14(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B29(700),
B30(2300), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900),B40(2300), B41(2500), B46(5200)

• 5G: N1 (FDD 2100 MHz), N3 (FDD 1800 MHz), N5 (FDD 850 MHz), N7 (FDD 2600 MHz), N8 (FDD 900
MHz), N28 (FDD 700 MHz), N40 (TDD 2300 MHz), N77 (TDD 3700 MHz), N78 (TDD 3500 MHz)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

www.infovista.com | 18
 • GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Audio Quality Measeurements2:

• sQLEAR

• POLQA

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• SM-N986B: Samsung Exynos 990 Octa-Core (2x2.73 GHz Mongoose M5 & 2x2.60 GHz Cortex-A76 &
4x2.0 GHz Cortex-A55)

• SM-N981U/W: Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz
Kryo 585)

• TEMS Connect License:

• SM-N986B: Samsung G

• SM-N981U/W: Qualcomm N
1 Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.
2 Audio Quality Measurements are not available on the SM-N986B.

9.3 Bug Corrections

• 00338364: TEMS 22.1.1 crash after 3h

• 00343790: AQM out of sync

• 00348055: G977B not correctly detected in TI 22.2

• 00344619: iPhone 11 stuck in hanging when script was stopped

• 00348372: CQI always 0 and SSB RSRP/ RSRQ are missing in connected mode from TEMS log

• 00345118: Huawei P40 Pro is not recording RTP messages during Volte calls

www.infovista.com | 19
• 00341860: Wrong Uplink Carrier Aggregation count

• 00344559: Huawei P40 decode wrong 5G I.E in SA network

• 00346136: TEMS Investigation Startup Problem

• 00348424: TI 22.2 can't decode NR SS RSSI

• 00345956: TI cell 無法跟站台相符 (Test sample not line to correct cell)

• 00347530: S20+ RRC ID info missing

10 TEMS™ Investigation 22.2

10.1 New TEMS Devices

10.1.1 Sony Xperia 1 II(mark2) 5G (XQ-AT51 and XQ-AT52)

The Sony Xperia 1 (mark II) is a Qualcomm SD865 chipset-based smartphone running Android 10. It is
introduced with TEMS firmware, which makes it ready for testing of existing and new networks with focus on data
service testing.

Specifications1:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM)

• Lock on Band (LTE/WCDMA/GSM)

• Lock on EARFCN+PCI2

• Lock on UARFCN

• Frequency bands:

• 5G: Sub6G Bands: n1, n3, n28, n77, n78

• 4G: FDD-LTE Bands: 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 19, 20, 25, 26, 28, 29, 32, 34, 38, 39, 40, 41, 46, 66

• 3G: WCDMA Bands: 1, 2, 4, 5, 6, 8, 19

• 2G: GSM Bands: 850, 900, 1800, 1900

• Throughput capabilities:

• NR Non-Standalone and Standalone mode

• LTE Category 19/13 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• LTE Carrier Aggregation DL 6CA/UL 2CA

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• MIMO

• VoLTE/VoWiFi

www.infovista.com | 20
• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• TEMS Connect License: Sony F

1 Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.
2 Both EARFCN and PCI must be set.

10.2 New Connectable Devices

10.2.1 LG Velvet 5G LM-G900UM

LG Velvet is a commercial smartphone based on the Qualcomm SD765G 5G platform. It is running Android 10 on
engineering firmware. It can be used for testing call setup and basic on-device data service testing.

• Chipset: Snapdragon 765G 5G mobile platform

• Connect License: Qualcomm N

10.2.2 Reintroduction of the Sony Ericsson W995

Support for the classic Sony Ericsson W995, offering unique control functionality on legacy networks when used
with TEMS Investigation, is now reintroduced.

10.3 New Features

10.3.1 Improved HTTP Get functionality

• The HTTP Get function is improved making it possible to end the session after a pre-defined amount of data
has been transferred.

• Users can now set the minimum payload that must have been transferred during an HTTP DL session to get
a sucessful result.

10.3.2 Additional IP information in logfiles

The OTT Facebook service testing now stores additional ip information (local IP address and server IP address)
in logfiles.

10.3.3 Additional WCDMA measurements

RLC DL/UL Throughput on WCDMA can now be recorded using Android devices based on the Samsung Exynos
chipset.

10.3.4 New NR Control Functionality

TEMS Investigation can now lock Qualcomm and Samsung chipset-based Android devices to NR+LTE RATs and
NR Bands. This makes it possible to make sure that devices stay on NSA 5G networks during measurements.

www.infovista.com | 21
10.3.5 Scanning improvements
• PCTEL: Added TD and FD LTE bands EU 53, 87, 88.

• PCTEL: Added NR 5G n53, n89 SUL FR1 band.

• PCTEL MXflex: DSS support

10.3.6 Check for missing licenses vs. phone capabilities

TEMS Investigation now checks if the correct set of licenses are available, compared to the device capabilities
(for example 5G technology option), and displays a warning if not. This helps users avoid the need to rerun drive
tests because of missing licensing.

10.3.7 Throughput charts in Mbps

Throughput charts can now display values in Mbps besides Kbps.

10.3.8 Improved NR Carrier display

Up to 8 NR Carriers can now be displayed in the TEMS Investigation GUI. This gives users a better overview of
NR carrier aggregation during the measuring or replay phase.

10.3.9 Python scripting improvements

• Improved OnDevice Python scripts execution

• Python script for native WhatsApp testing

• Add support for .pyc to ODM Scripting

10.3.10 New NR Information Elements/Events

In this release of TEMS Investigation a large number of information elements and events has been added to all
three supported 5G chipsets. All additions are listed below.

10.3.10.1 Qualcomm

• NR SS RSSI

• DCI Format 0_0 Samples Per Carrier

• DCI Format 0_1 Samples Per Carrier

• DCI Format 2_0 Samples Per Carrier

• DCI Format 2_1 Samples Per Carrier

• DCI Format 2_2 Samples Per Carrier

• DCI Format 2_3 Samples Per Carrier

• DCI Format 0_0 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 0_1 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 2_0 Aggregation Level <1,2,4,8,16> Samples Per Carrier

www.infovista.com | 22
• DCI Format 2_1 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 2_2 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 2_3 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• Call Attempt EPSFB

• Call Setup EPSFB

• Call Established EPSFB

• Call Blocked EPSFB

• Voice Bearer Established event

• NR Serving Cell RRC Cell Identity (Complete)

• NR Serving Cell TAC

• NR Serving Cell RANAC

• Serving MCC/MNC/PLMN updated in NR SA mode

10.3.10.2 Samsung

• NR SS RSSI

• Serving Cell PDSCH SINR

• DCI Format 0_0 Samples Per Carrier

• DCI Format 0_1 Samples Per Carrier

• DCI Format 0_0 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 0_1 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• Call Attempt EPSFB

• Call Setup EPSFB

• Call Established EPSFB

• Call Blocked EPSFB

• Voice Bearer Established event

• NR Serving Cell RRC Cell Identity (Complete)

• NR Serving Cell TAC

• NR Serving Cell RANAC

• Serving MCC/MNC/PLMN updated in NR SA mode

10.3.10.3 HiSilicon

• Serving Cell <1-4> PDSCH MCS Distribution CW<0-1> Count Current

• Serving Cell <1-4> PUSCH MCS Distribution Count Current

• Serving Cell <1-4> PUSCH MCS Distribution (Accu)

www.infovista.com | 23
• Serving Cell <1-4> PDSCH RI Distribution Count Current

• PDSCH RI Current Sample Max

• PDSCH RI Current Sample Min

• PDSCH RBG Size

• PUSCH RBG Size

• Serving Cell SSB Beam Count

• PDSCH Modulation CW<0-1> Current Max

• PDSCH Modulation CW<0-1> Current Min

• PDSCH Modulation CW<0-1> Distribution Current Sample Count

• PUSCH Modulation Current Max

• PUSCH Modulation Current Min

• PUSCH Modulation Distribution Current Sample Count

• PDSCH MCS CW<0-1> Current Max

• PDSCH MCS CW<0-1> Current Min

• PDSCH MCS CW<0-1> Distribution Current Sample Count

• PUSCH MCS Current Max

• PUSCH MCS Current Min

• PUSCH MCS Distribution Current Sample Count

• Serving Cell Name

• Serving Cell Distance

• Serving Duplex Mode (text)

• Serving Cell SSB Periodicity (ms)

• PDSCH PRB Allocation Count Per Carrier

• PDSCH PRB Allocation Count TB<1-2>

• PDSCH Slot Allocation Count Per Carrier

• PDSCH Slot Allocation Count TB<1-2>

• PUSCH PRB Allocation Count Per Carrier

• PUSCH Slot Allocation Count Per Carrier

• PUSCH Avg RB/Allocated Slot Per Carrier

• UE Power Class

• PDSCH Modulation Distribution Current (%)

• PUSCH Modulation Distribution Current (%)

www.infovista.com | 24
• PDSCH MCS Distribution Current (%)

• PUSCH MCS Distribution Current (%)

• PDSCH RI Distribution Current (%)

• TDD UL/DL Configuration Type

• TDD UL/DL Configuration Pattern Count

• TDD UL/DL Configuration Periodicity

• TDD Symbols UL %

• TDD Symbols DL %

• TDD Symbols Flexible %

• Initial BWP Bandwidth DL

• Initial BWP Bandwidth UL

• Initial BWP Start Point NR-ARFCN DL

• Initial BWP Start Point NR-ARFCN UL

• BWP Start Point NR-ARFCN DL

• BWP Start Point NR-ARFCN UL

• FTP Upload Success Rate Accumulated

• FTP Download Success Rate Accumulated

• Serving Cell Frequency DL

• Serving Cell Frequency UL

• DCI Forömat 1_0 Samples Per Carrier

• DCI Format 1_1 Samples Per Carrier

• DCI Format 1_0 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• DCI Format 1_1 Aggregation Level <1,2,4,8,16> Samples Per Carrier

• RRC A1 Event

• RRC A2 Event

• RRC A3 Event

• RRC A4 Event

• RRC A5 Event

• RRC A6 Event

10.3.11 Default AQM language

TEMS Investigation is now using the English 3 speech sample as default language for Audio Quality
Measurements permformed with the POLQA algorithm.

www.infovista.com | 25
10.4 Corrected Bugs

• 335325: Issue with Network Bandwidth Test on Huawei Dongle E392

• 345265: G988B device does not decode some NR IEs

• 344458: P40 missing NAS message in 5G SA mode

• 345158: ODM installation issue

• 343502: TI is not recognizing NR metrics in a file with a high throughput in NR when replayed as Raw

• 346177: NR values not seen - BTH5 firmware

11 TEMS™ Investigation 22.1.4

11.1 New Features

11.2 New connectable devices

11.2.1 Oppo Find X2 (CPH2023)

The Oppo Find X2 is a smartphone based on the Qualcomm 865 Mobile Platform. It is running Android 10 and
this particular model is introduced as connectable in TEMS Investigation 22.1.4 making it ready to test 5G
networks and deployments. As other connectable devices, the Oppo Find X2 can run basic on-device software
making it possible to test data throughput using HTTP, FTP and Ping.

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

11.2.2 Xiaomi Mi 10 5G (M2001J2C)

The Xiaomi Mi 10 5G is a smartphone based on the Qualcomm 865 Mobile Platform. It is running Android 10. It is
introduced as connectable in TEMS Investigation 22.1.4, making it ready to test 5G networks and deployments.
With on-device software, it is possible to perform data throughput testing (HTTP, FTP, Ping) and voice call setup
testing on LTE and NR 5G networks.

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

11.3 New information elements

• Added LTE MAC UL/DL Throughput Per Carrier information elements

11.4 Corrected Bugs

• 327915: Urgent issue with TEMS Discovery exports

• 329491: AQM measurement - RTP Lost Packet Rate Audio, wrong value

• 329549: No LTE PDCP DL throughput

www.infovista.com | 26
• 335385: Violation of PRIMARY KEY constraint 'PK_SessionsInArea'

• 336746: Huawei P40 ODM call control doesn't work

• 336790: iPhone SIP frames timestamps and data IP

• 337407: Cell file question

• 337575: Visualization issue about SCC in mode report LTE LL1 CA Cell Info Message

• 337711: XML Cell Format Invalid CI data type format for NR

• 337715: Replay issue

• 337889: A3 Event erroneous information

• 337915: Parameter missing for Huawei P40

• 338092: RDE Problem

• 338537: Crashing while loading cell file

• 338886: Huawei P40 can't decode detected beam RF parameter

• 339387: NR Attributes are not visible SINR & PDSCH Num Layers

• 340553: UE Tx Power (dBm)

• 340673: LTE CINR is not showing on Huawei P40 Pro

• 341005: LTE MAC RACH Attempt Unknown

• 341066: NR MAC UL missing

• 341689: Security Association missing

• 344263: NR PUSCH Throughput Too Low

• 344264: Can't export NR MAC UL

11.5 Removed Features

There are no removed features in this release.

12 TEMS™ Investigation 22.1.3

12.1 New TEMS Devices

12.1.1 OnePlus 8 5G (IN2011, IN2013, IN2017)

The OnePlus 8 5G is a smartphone based on the Qualcomm 865 Mobile Platform and the Qualcomm X55 5G
modem. It is running Android 10 and introduced with TEMS firmware in TEMS Investigation 22.1.3. This makes it
ready for testing of LTE and NR 5G networks and developments with full on-device software support and support
for Audio Quality Measurements.

Specifications*:

• Control functions:

www.infovista.com | 27
 • Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• Lock on Cell (EARFCN or UARFCN)

• Audio Quality Measurements

• sQLEAR

• POLQA

• Frequency bands:

• GSM: GSM850, GSM900, GSM1800, GSM1900

• WCDMA: B1, B2, B4, B5, B8, B9, B19

• CDMA: BC0

• LTE-FDD: B1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 18, 19, 20, 25, 26, 28, 32, 66

• LTE-TDD: B34, 38, 39, 40, 41, 42, 46

• 5G: n78 (n1, n3, n7, n28 will be supported later through upgrades)

• Throughput capabilities:

• NR Non-Standalone and Standalone mode

• LTE: Category 18/13 capable (Up to DL: 1.2 Gbit/s, UL: 150 Mbit/s)

• MIMO (LTE: B1, 3, 7, 38, 40, 41 NR: n1, n3, n7, n78)

• VoLTE/VoWiFi

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

12.1.2 Xiaomi Mi 10 Pro (M2001J2G)

The Mi 10 Pro from Xiaomi is a Qualcomm SD865 chipset-based smartphone running Android 10. It is introduced
in TEMS Investigation with TEMS firmware, which makes it ready for testing of existing and new networks with
focus on both data and voice quality.

Specifications*:

• Control functions:

www.infovista.com | 28
 • Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• Lock on Cell (EARFCN or UARFCN)

• Audio Quality Measurements

• sQLEAR

• Frequency bands:

• 5G: Sub6G: n1/n3/n7/n28/n77/n78

• 4G: FDD-LTE: 1/2/3/4/5/7/8/20/28/32

• 4G: TD-LTE: 38/40

• 3G: WCDMA: B1/B2/B4/B5/B8

• 2G: GSM: B2/B3/B5/B8

• Throughput capabilities:

• NR Non-Standalone and Standalone mode

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• MIMO

• VoLTE/VoWiFi

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

12.1.3 Samsung Galaxy S20+ 5G (SC-52A)

The Galaxy S20+ 5G is an Android 10 smartphone based on a Qualcomm chipset. The device is capable of
measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s UL) and 5G
throughput up to 5+ Gbit/s and prepared for Audio Quality Measurements.

Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

www.infovista.com | 29
 • LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B32(1500),
B34(2000), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500)

• 5G: N1 (FDD 2100 MHz), N3 (FDD 1800 MHz), N5 (FDD 850 MHz), N7 (FDD 2600 MHz), N8 (FDD 900
MHz), N28 (FDD 700 MHz), N40 (TDD 2300 MHz), N77 (TDD 3700 MHz), N78 (TDD 3500 MHz), N260
(5G mmWave 39 GHz), N261 (5G mmWave 28 GHz)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

www.infovista.com | 30
• Chipset/CPU:

• Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License:

• Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

12.2 New connectable devices

12.2.1 Samsung Note 20 and Note 20+ 5G (SM-N981W, SM-N986W)

The Galaxy Note 20 and Note 20+ are 5G ready Android 10 smartphones based on a Qualcomm chipset. It is
capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316 Mbit/s UL).

• Chipset: Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License: Qualcomm N

12.2.2 VSmart Aris Max 5G

The VSmart Aris 5G belongs to the high-end segment. It come with an 8GB RAM, Snapdragon 765 chip,
4000mAh battery, 128GB ROM, and support for 5G Sub 6 GHz networks. To make the device as secure as
possible, it also integrates the Quantis QRNG security chip with quantum computing technology.

• High-security profile

• Chipset: Snapdragon 765G 5G mobile platform

• Connect License: Qualcomm N

12.3 New Features

12.3.1 Scanning enhancements

• TEMS Investigation now supports use of the TP-5GDC converter. TP-5GDC is a RF down-converter
supporting three mm-Wave bands. In combination with TSME6, it allows to do 5G NR measurements in the
frequency ranges 24.25 – 27.5 GHz / 26.5 – 29.5 GHz / 37 – 40 GHz.

• New FR1 bands n90-n95 supported

• Support for LTE NB-IoT & LTE-LAA MIMO information elements

• Support for 2nd SSB RSSI values for FR2 (mmWave) PCTEL scanner

12.4 Corrected Bugs

• 337958: Not able to cell lock in TI 22.1.2

• 333104: WNC X55 Device not detected.

• 340227: Missing UE Tx Power

www.infovista.com | 31
• 334244: Call setup time 0 for successful MT calls.

• 334522: Multiple issues with TEMS Export Utility

• 334737: TI can’t detect Huawei Mate 30

• 336987: NR CA Throughput and values missing for additional cells

• 337613: Updated Qualcomm messages after FW upgrade

• 335670: NR SCG Cell Addition and Cell Removal issue

• 337465: HiSilicon parameters reporting issue

• 333758: Wrong call drop information

• 338793: Too low throughput values on 5G measurements

13 TEMS™ Investigation 22.1.2

13.1 New Features

13.1.1 Network status is recorded before a call is initiated

TEMS Investigation now records the device network status to the logfile before a call is initiated. This function
makes it easier to evaluate the call result.

13.2 Corrected Bugs

• 335947: Scripting action does not work as expected.

• 334569: No NR RF parameters on SM-N9760 running Android 10.

• 334576: Huawei Mate 30 5G wrong NR PUSCH throughput.

• 336129: Motorola Edge+ XT2061-3 does not connect correctly to TEMS Investigation.

14 TEMS™ Investigation 22.1.1

14.1 Corrected Bugs

• 334464: TEMS Iphone Xs M2M calls fails.

15 TEMS™ Investigation 22.1

15.1 New TEMS Devices

15.1.1 Samsung Galaxy S20+ SM-G9860/W and S20 Ultra SM-G988B

The Galaxy S20+ 5G is an Android 10 smartphone based on a Qualcomm or Samsung chipset (depending on
market). The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and
316 Mbit/s UL) and 5G throughput up to 5+ Gbit/s.

www.infovista.com | 32
Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• 4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B32(1500),
B34(2000), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500)

• 5G: N1 (FDD 2100 MHz), N3 (FDD 1800 MHz), N5 (FDD 850 MHz), N7 (FDD 2600 MHz), N8 (FDD 900
MHz), N28 (FDD 700 MHz), N40 (TDD 2300 MHz), N77 (TDD 3700 MHz), N78 (TDD 3500 MHz), N260
(5G mmWave 39 GHz), N261 (5G mmWave 28 GHz)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

www.infovista.com | 33
 • DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• SM-G988B: Samsung Exynos 990 Octa-Core (2x2.73 GHz Mongoose M5 & 2x2.60 GHz Cortex-A76 &
4x2.0 GHz Cortex-A55)

• SM-G9860/W: Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz
Kryo 585)

• Connect License:

• SM-G988B: Samsung G

• SM-G9860/W: Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

15.2 New Connectable Devices

15.2.1 Apple iPhone 11

The Apple iPhone 11 has been added as a connectable device in TEMS Investigation 22.1. This makes it
possible to perform data tests and perform audio calls to test including others call setup with one of the most
popular smartphones on the market.

• Connect License: Apple A

15.2.2 Huawei P40 (ELS-N04, NX9, TN00, AN00)

The Huawei P40 is a 5G ready smartphone based on the HUAWEI Kirin 990 5G chipset. It is running Android 10
and introduced as connectable in TEMS Investigation 22.1. Use it with basic on-device software to perform call
setup tests, and voice call setup tests.

• Chipset/CPU: HUAWEI Kirin 990 5G (Octa-core 2 x Cortex-A76 Based 2.86 GHz + 2 x Cortex-A76 Based
2.36 GHz + 4 x Cortex-A55 1.95 GHz)

• Connect License: HiSilicon C

15.2.3 Oppo Find X2 (CHP2025)

The Oppo Find X2 is a smartphone based on the Qualcomm 865 Mobile Platform. It is running Android 10 and
introduced as connectable in TEMS Investigation 22.1 making it ready to test 5G networks and deployments. As
other connectable devices, the Oppo Find X2 can run basic on-device software making it possible to test data
throughput using HTTP, FTP and Ping.

www.infovista.com | 34
• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

15.2.4 OnePlus 8 5G (IN2017)

The OnePlus 8 5G is a smartphone based on the Qualcomm 865 Mobile Platform and the Qualcomm X55 5G
modem. It is running Android 10 and introduced as a connectable device in TEMS Investigation 22.1. This makes
it ready for testing of LTE and NR 5G networks and developments with basic on-device software for data
throughput (HTTP, FTP and Ping) and voice call setup.

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

15.2.5 Motorola Edge Plus (XT2061-3)

The Motorola Edge Plus is a smartphone based on the Qualcomm 865 Mobile Platform. It is running Android 10
that has a powerful 5000 mAh battery. It is introduced as connectable in TEMS Investigation 22.1, making it ready
to test 5G networks and deployments. With on-device software, it is possible to perform data throughput testing
(HTTP, FTP, Ping) and voice call setup testing on LTE and NR 5G networks.

• Chipset/CPU: Qualcomm® Snapdragon™ 865 Mobile Platform

• Connect License: Qualcomm N

15.2.6 Samsung Galaxy S20 (SM-G985F,SM-G980U, SM-G985U, SM-G988U, SM-G980W,

SM-G985W, SM-G9800, SM-G9850, SM-G9810)
In TEMS Investigation 22.1, the entire Samsung Galaxy S20 series can be connected and used for network
testing and evaluation. The Galaxy S20 is an Android 10 smartphone based on a Qualcomm or Samsung chipset
(depending on market). The device is capable of measuring high speed data throughput performance (LTE up to
2 Gbit/s DL and 316 Mbit/s UL) and some models are ready for 5G.

• TEMS Connect License: Samsung G/Qualcomm N

15.2.7 Xiaomi Mi 10 Pro (M2001J2G)

The Xiaomi Mi 10 Pro is a smartphone based on the Qualcomm 865 Mobile Platform. It is running Android 10. It is
introduced as connectable in TEMS Investigation 22.1, making it ready to test 5G networks and deployments.
With on-device software, it is possible to perform data throughput testing (HTTP, FTP, Ping) and voice call setup
testing on LTE and NR 5G networks.

• Chipset/CPU:

• Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz Kryo 585)

• Connect License: Qualcomm M

www.infovista.com | 35
15.3 New Features

15.3.1 Device Sensor Monitoring

New information elements showing available device memory, battery level and CPU temperatures have been
implemented and can be monitored in TEMS Investigation 22.1. Availability varies depending on device model
and Android version.

15.3.2 Easy Access Airplane Mode Toggle

It is now possible to toggle airplane mode easily and quickly on a device by right-clicking on it in the equipment
navigator.

15.3.3 Text Export Enhancements

The text export has been improved by removing the frame number column and allowing the user to select which
optional columns to include in the export. It is also now possible to export the entire content of a message window
to a CSV file by right clicking in the message window.

15.3.4 New DSS Analysis Worksheet

A new worksheet has been added to the Investigation NR LTE workspace. This worksheet contains most of the
information elements for DSS/MR-DC analysis and is optimally configured for an NSA device connected as EQ1
and an LTE only device connected as EQ2.

15.3.5 Support for Italian Speech Sample

TEMS™ Investigation 22.1 has support for performing voice quality measurements using an Italian speech
sample.

15.3.6 Scanning improvements

• Simultaneous 4G/5G FR1 and 5G FR2 measurements using the PCTEL HBflex scanner.

• NB-IoT mode now available in LTE Network Scan for PCTEL scanners.

• New Scanning Information Elements:

• Network Search NB-IoT Operation Mode

• Network Search NB-IoT Standard LTE EARFCN

• Network Search NB-IoT Frequency Offset

15.3.7 New NR Information Elements

15.3.7.1 Qualcomm

• MR-DC DRB CN

• MR-DC DRB EPS Bearer ID

• MR-DC DRB PDU Session ID

www.infovista.com | 36
• MR-DC DRB PDCP Type

• MR-DC DRB QCI

• MR-DC DRB RLC DL Path

• MR-DC DRB RLC UL Path

• MR-DC DRB Mode

• MR-DC DRB ID

• MR-DC DRB Type

• NR Serving Cell DSS Configured Frequency

• NR Serving Cell DSS Configured Band

• NR Serving Cell DSS Configured Bandwidth

• Inter-System NR Neighbor Cell SS-RSRP

• Inter-System NR Neighbor Cell SS-RSRQ

• Inter-System NR Neighbor Cell SS-SINR

• Inter-System NR Neighbor Cell Identity

• Inter-System NR Neighbor Cell NR-ARFCN

• Cell Statistics PDSCH Byte Count

• Cell Statistics NR-ARFCN

• Cell Statistics PCI

15.3.7.2 Samsung

• DCI Format 1_0 Samples Per Carrier

• DCI Format 1_1 Samples Per Carrier

• DCI Format 1_0 Aggregation Level <1, 2, 4, 8, 16> Samples Per Carrier

• DCI Format 1_1 Aggregation Level <1, 2, 4, 8, 16> Samples Per Carrier

• MAC UL BLER Initial

• PDSCH Physical Throughput (CRC OK) Per Carrier

• PDSCH Physical Throughput (CRC OK) Total

• RACH Initial Tx Power

• RACH Current Tx Power

• RACH Number of Transmits

• RACH Latency

15.3.7.3 HiSilicon

• NR RACH Attempt Event

www.infovista.com | 37
• NR RACH Success Event

• NR RACH Failure Event

• NR SCG Cell Addition Event

• NR SCG Cell Removal Event

• NR SCG Cell Reconfiguration Event

• NR SCG Failure Event

• NR Session Duration

• Serving SSB Beam Changed Event

• EUTRAN RRC B1-NR Event

• EUTRAN RRC B2-NR Event

• PUSCH Num Layers

• PDSCH Num Layers

• PDSCH MCS Distribution Accumulated

• PDSCH Rank Indicator Distribution Accumulated

• PUSCH Resource Block Allocation Count

• PDSCH Resource Block Allocation Count

• Bandwidth Part ID Downlink

• Bandwidth Part Center NR-ARFCN Downlink

• Bandwidth Parts Configured Count Downlink

• Bandwidth Part ID Uplink

• Bandwidth Part Center NR-ARFCN Uplink

• Bandwidth Parts Configured Count Uplink

• Bandwidth Part Downlink Changed Event

• Bandwidth Part Uplink Changed Event

• Bandwidth Part Bandwidth Downlink

• Bandwidth Part Bandwidth Uplink

• Bandwidth Part SCS Downlink

• Bandwidth Part SCS Uplink

• Cyclic Prefix Downlink

• Cyclic Prefix Uplink

• Phy Throughput Multi-RAT DL

• Phy Throughput Multi-RAT UL

www.infovista.com | 38
• PDSCH RI Distribution Current Sample Count

• Serving Cell <1-4> PDSCH Modulation Distribution CW<0-1> (Accu)

• Serving Cell <1-4> PDSCH Modulation Distribution CW<0-1> Count Current

• Serving Cell <1-4> PUSCH Modulation Distribution (Accu)

• Serving Cell <1-4> PUSCH Modulation Distribution Count Current

15.4 Corrected Bugs

• 00329589 – NR PDCP throughput wrong

• 00330177 – FTP can’t login if password contains special character

• 00331082 – R&S TSMW Scanner giving to many LTE Active Set servers

• 00331351 – SSB SINR missing

• 00332803 – Commercial Device Throughput Metrics for On Device Data Tests HTTP, FTP, Iperf

• 00332775 – S20 Devices Unable to make Voice Calls

• 00332742 – Problem to choose bands/frequencies

• 00331896 – Issue record wrong value for NR RLC Throughput

• 00333127 – 5G Scanner Logs Issue

• 00330340 – Bar chart, Multiple IE components, Colors not applied

• 00330964 – SMS Access Delay issue

• 00329491 – AQM Measurement – RTP Lost Packet Rate Audio, wrong value

• 00333783 – Fake LTE Inter-frequency Handover Failures in replay

• 00333387 – LTE Neighbor cells showing incorrect values

• 00333311 – Replaying TP Xiaomi Mi Mix 3 5G trp shows fake dropped calls

16 TEMS™ Investigation 22.0.1

TEMS Investigation 22.0.1 comes with support for Samsung Galaxy S20+ with TEMS firmware. This makes it
possible to perform advanced data and voice quality network testing with the latest Samsung devices. In addition
to that, a number of new 5G smartphones together with a NB-IoT device are added as connectable to TEMS
Investigation.

16.1 New TEMS Devices

16.1.1 Samsung Galaxy S20+ 5G SM-G986B/U

The Galaxy S20+ 5G is an Android 10 smartphone based on a Qualcomm or Samsung chipset (depending on
market). The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and
316 Mbit/s UL) and 5G throughput up to 5+ Gbit/s.

The Qualcomm based SM-G986U is tuned for Audio Quality Testing using the POLQA algorithm.

www.infovista.com | 39
Specifications*:

• Control functions:

• Lock on RAT (NR/LTE/WCDMA/GSM/Wi-Fi)

• Lock on Band (LTE/WCDMA/GSM/Wi-Fi)

• LTE Cell lock

• LTE PCI lock

• WCDMA Cell lock

• WCDMA Scrambling Code lock

• GSM Cell lock

• GSM Channel lock

• CA Control

• AMR WB Control

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• SM-G986B:
4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B66(AWS-3), B71(600)

• SM-G986B:
4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500), B46(5200), B48(3600)

• SM-G986U:
4G FDD LTE: B1(2100), B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700),
B13(700), B17(700), B18(800), B19(800), B20(800), B25(1900), B26(850), B28(700), B32(1500),
B34(2000), B66(AWS-3)

• SM-G986U:
4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500)

• 5G: N1 (FDD 2100 MHz), N3 (FDD 1800 MHz), N5 (FDD 850 MHz), N7 (FDD 2600 MHz), N8 (FDD 900
MHz), N28 (FDD 700 MHz), N40 (TDD 2300 MHz), N77 (TDD 3700 MHz), N78 (TDD 3500 MHz), N260
(5G mmWave 39 GHz), N261 (5G mmWave 28 GHz)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

www.infovista.com | 40
 • LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• VoLTE/VoWiFi

• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• SM-G986B: Samsung Exynos 990 Octa-Core (2x2.73 GHz Mongoose M5 & 2x2.60 GHz Cortex-A76 &
4x2.0 GHz Cortex-A55)

• SM-G986U: Qualcomm SD865 Octa-core (1x2.84 GHz Kryo 585 & 3x2.42 GHz Kryo 585 & 4x1.8 GHz
Kryo 585)

• Connect License:

• SM-G986B: Samsung G

• SM-G986U: Qualcomm N

*Depending on network and SIM-card. The device radio settings are reconfigured every time a new SIM card is
inserted to the phone, therefore, you need to test in the specific network to obtain a correct value for band support
and capabilities.

16.2 New Connectable Devices

16.2.1 Samsung Galaxy S20 SM-G980F/SM-G981B

The Galaxy S20 is an Android 10 smartphone based on a Qualcomm or Samsung chipset (depending on market).
The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and 316
Mbit/s UL). In this release, two flavors based on the Samsung Exynos chipset are added as connectable in TEMS
Investigation.

• TEMS Connect License: Samsung G

16.2.2 Samsung Galaxy S20 Ultra SM-G988B

The Galaxy S20+ 5G is an Android 10 smartphone based on a Qualcomm or Samsung chipset (depending on
market). The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and
316 Mbit/s UL) and 5G throughput up to 5+ Gbit/s. In this release, the SM-G988B is added as connectable to
TEMS Investigation.

• TEMS Connect License: Samsung G

www.infovista.com | 41
16.2.3 LG v60 ThinQ 5G LM-V600TM
The LG ThinQ 5G is a 5G ready Android smartphone based on the octa-core Qualcomm Snapdragon SD865
chipset branded for T-Mobile.

• TEMS Connect License: Qualcomm N

16.2.4 Telit ME910C1 M1/NB1 IoT module

The ME910C1 is the Category M1/NB1 evolution of the Telit LE910 Series of LTE modules. The ME910C1 is an
LTE UE Category M1/NB1 device with maximum downlink and uplink data rate in the range of 300kbps. This
model further enriches the widely deployed Telit xE910 family of 28 x 28 mm LGA modules.

• TEMS Connect License: Qualcomm N

16.2.5 Huawei Mate 30 Pro 5G LIO-N29

The Huawei Mate 30 Pro is a 5G ready Android smartphone built on the Huawei Kirin 990 5G chipset.

• Processor:

• Huawei Kirin 990 5G

• Processor clock: 2.86 GHz

• Number of cores: 8

• TEMS Connect License: Huawei

16.3 New Features

16.3.1 NB-IoT Signal Scan with L3 message

L3 Messages can now be recorded when performing NB-IoT Signal Scan with PCTEL IBflex or HBflex scanners.

16.3.2 New information element support

Support for the following information elements was added for HiSilicon devices:

• PDSCH BLER (%)

• PDSCH BLER (%)

• PUSCH BLER (%)

• UE PUCCH Tx Power (dBm)

• UE PUCCH/PUSCH Power Offset (dB)

• Serving Cell DL Pathloss (dB)

• RLC DL Channel ID

• RLC DL RB Throughput (kbit/s)

• RLC DL Mode

www.infovista.com | 42
• RLC DL Throughput (kbit/s)

• RLC UL Channel ID

• RLC UL RB Throughput (kbit/s)

• RLC UL Throughput (kbit/s)

• RLC UL Mode

16.4 Corrected Bugs

• 305854: Audio Quality Measurements overlap.

• 314432: Upper limit for IE Line Chart.

• 320464: TEMS Investigation Export - Server busy.

• 322593: Wrong count of serving cell in Uplink Carrier Aggregation.

• 323071: No 5G messages after WNC fw upgrade.

• 327071: Smartphone GPS problem.

• 327756: Missing TCP messages.

• 328495: Export AT config.

• 328523: Sony Xperia XZ2 log files missing data.

• 328740: NR values missing.

• 329070: Band n41 is N/A in Network scan with PCTEL IBflex.

• 329564: Licenses for RDE 22.

• 329565: Failed Voice session issues.

• 330279: SS SINR in missing on 5G after fw update on Note 10+.

• 330532: Huawei Mate 30 5G Pro has no NR KPI.

• 330608: LG V60 ThinQ not working.

• 330787: Cannot launch TEMS Investigation.

• 330878: 5G Blind Scan not working.

• 331916: When scanning NR Band 28, NR-ARFCN is missing.

• 331999: TEMS Investigation crashes on iBFlex Wi-Fi measurements.

16.5 Removed Features

There are no removed features.

17 TEMS™ Investigation 22.0

Again, TEMS Investigation strengthens its place as the 5G leader in the Network Testing industry by being first to
enable a long list of new 5G devices for network testing in this release. In addition to that, TEMS Investigation

www.infovista.com | 43
22.0 comes with support for decoding of logs recorded by the HiSilicon 5G chipset, and heavily improved 5G
scanning functionality.

17.1 New Connectable Devices

17.1.1 Huawei Mate 20 X 5G EVR-AN00

The Huawei Mate 20 X is a 5G ready Android smartphone built on the Huawei Kirin 980 chipset with the Balong
5000 5G modem.

• Technology: GSM / HSPA / LTE / 5G

• Band Support:

• 5G NR: N77 / N78 / N79

• 4G LTE TDD: B34 / B38 / B39 / B40 / B41

• 4G LTE FDD: B1 / B2 / B3 / B4 / B5 / B6 / B7 / B8 / B9 / B12 / B17 / B18 / B19 / B20 / B26 / B28 / B32

• 3G WCDMA: B1 / B2 / B4 / B5 / B6 / B8 / B19

• 2G GSM: B2 / B3 / B5 / B8 (850 / 900 / 1800 / 1900 MHz)

• Data speed:

• HSPA 42.2/5.76 Mbps

• LTE-A Cat21 1400/200 Mbps

• 5G (2+ Gbps DL)

• HiSilicon Kirin 980 5G Octa-core (2 x Cortex A76 2.6 GHz + 2 x Cortex A76 1.92 GHz + 4 x Cortex A55 1.8
GHz) and Balong 5000 5G modem.

• TEMS Connect License: Huawei

17.1.2 Huawei Mate 20 X 5G EVR-N29

The Huawei Mate 20 X is a 5G ready Android smartphone built on the Huawei Kirin 980 chipset with the Balong
5000 5G modem.

• Technology: GSM / HSPA / LTE / 5G

• Band support:

• 2G bands: GSM 850 / 900 / 1800 / 1900

• 3G bands: HSDPA 800 / 850 / 900 / 1700(AWS) / 1900 / 2100

• 4G bands: LTE band 1(2100), 2(1900), 3(1800), 4(1700/2100), 5(850), 6(900), 7(2600), 8(900), 9(1800),
12(700), 17(700), 18(800), 19(800), 20(800), 26(850), 28(700), 32(1500), 34(2000), 38(2600), 39(1900),
40(2300), 41(2500)

• 5G bands: 77(3700), 78(3500), 79(4700); SA/NSA/Sub6

• Data speed:

• HSPA 42.2/5.76 Mbps

www.infovista.com | 44
 • LTE-A Cat21 1400/200 Mbps

• 5G (2+ Gbps DL)

• HiSilicon Kirin 980 5G Octa-core (2 x Cortex A76 2.6 GHz + 2 x Cortex A76 1.92 GHz + 4 x Cortex A55 1.8
GHz) and Balong 5000 5G modem.

• TEMS Connect License: Huawei

17.1.3 Huawei Mate 30 5G TAS-AN00

The Huawei Mate 30 Pro is a 5G ready Android smartphone built on the Huawei Kirin 990 5G chipset.

• Band Support:

• GSM frequencies: 850 900 1800 1900

• UMTS: 850 900 1900 2100

• LTE: FDD LTE: 2600, 2100, 1900, 1800, 1700, 900, 850, 800, 700, TDD LTE: 2600, 2300, 1900

• 5G: Yes

• Processor:

• Huawei Kirin 990 5G

• Processor clock: 2.86 GHz

• Number of cores: 8

• TEMS Connect License: Huawei

17.1.4 Huawei Mate 30 Pro 5G LIO-AN00

The Huawei Mate 30 Pro is a 5G ready Android smartphone built on the Huawei Kirin 990 5G chipset.

• Band Support:

• GSM frequencies: 850 900 1800 1900

• UMTS: 850 900 1900 2100

• LTE: FDD LTE: 2600, 2100, 1900, 1800, 1700, 900, 850, 800, 700, TDD LTE: 2600, 2300, 1900

• 5G: FDD 5G: 2100, 1800, 700, TDD 5G: 4700, 3500, 2600, 2500

• Processor:

• Huawei Kirin 990 5G

• Processor clock: 2.86 GHz

• Number of cores: 8

• TEMS Connect License: Huawei

17.1.5 LG v60 ThinQ 5G LM-V600EA

The LG ThinQ 5G is a 5G ready Android smartphone based on the octa-core Qualcomm Snapdragon SD865
chipset.

www.infovista.com | 45
• GSM frequencies: 850 900 1800 1900

• UMTS: 850 900 1900 2100

• LTE: FDD LTE: 2600, 2100, 1900, 1800, 1700, 900, 850, 800, 700, TDD LTE: 2600, 2500, 2300, 2000, 1900

• 5G: FDD 5G: 2100, 1800, TDD 5G: 4700, 3700, 3500, 2500

• Chipset/CPU:

• Qualcomm SDM865 Octa-core

• TEMS Connect License: Qualcomm N

17.1.6 OnePlus 8 5G IN2023

The new Qualcomm SD865 based OnePlus device can be connected to TEMS Investigation as soon as it is
available.

• TEMS Connect License: Qualcomm N

17.1.7 Samsung Galaxy S20+ 5G SM-G986B

The Galaxy S20+ 5G is an Android 10 smartphone based on a Qualcomm chipset, aimed at the European
market. The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and
316 Mbit/s UL).

Specifications*:

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• 3G TD-SCDMA: B34(2010), B39(1880)

• 4G FDD LTE: B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700), B13(700),
B18(800), B19(800), B20(800), B26(850), B28(700), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500), B46(5200), B48(3600)

• Throughput capabilities:

• LTE: Category 20/20 capable (Up to DL: 2.0 Gbit/s, UL: 316 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

www.infovista.com | 46
• Modulation:

• DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Samsung Exynos 990 Octa-Core (2x2.73 GHz Mongoose M5 & 2x2.60 GHz Cortex-A76 & 4x2.0 GHz
Cortex-A55)

• Connect License: Samsung G

*Depending on network and SIM-card, all functions

17.1.8 Samsung Galaxy S20 Ultra 5G SM-G9880

The Galaxy S20 Ultra 5G is an Android 10 smartphone based on a Qualcomm chipset, aimed at the Chinese
market. The device is capable of measuring high speed data throughput performance (LTE up to 2 Gbit/s DL and
150 Mbit/s UL).

Specifications*:

• Frequency bands:

• 2G GSM: GSM850, GSM900, DCS1800, PCS1900

• 2G CDMA: CDMA800, USPCS1900

• 3G UMTS: B1(2100), B2(1900), B5(850), B8(900)

• 3G CDMA: BC0(800), BC1(1900)

• 3G TD-SCDMA: B34(2010), B39(1880)

• 4G FDD LTE: B2(1900), B3(1800), B4(AWS), B5(850), B7(2600), B8(900), B12(700), B13(700),
B18(800), B19(800), B20(800), B26(850), B28(700), B66(AWS-3)

• 4G TDD LTE: B38(2600), B39(1900), B40(2300), B41(2500), B46(5200), B48(3600)

• Throughput capabilities:

• LTE: Category 20 capable (Up to DL: 2.0 Gbit/s, UL: 150 Mbit/s)

• HSDPA Category 24 (42 Mbit/s), HSUPA Category 6 (5.8 Mbit/s)

• GPRS/EDGE Class 12

• LAA

• LTE-A (7CA DL)

• 4x4 MIMO

• Modulation:

www.infovista.com | 47
 • DL: 256QAM

• UL: 256QAM

• Google Android 10

• WLAN 802.11a/b/g/n/ac (2.4 and 5 GHz)

• Wi-Fi 6 (up to 1.5 Gbit/s)

• Chipset/CPU:

• Qualcomm SDM865 Octa-core

• Connect License: Qualcomm N

*Depending on network and SIM-card, all functions

17.1.9 Sony Xperia 1 II(mark2) 5G

The Sony Xperia 1 II (mark2) 5G is a 5G ready Android smartphone based on the Qualcomm Snapdragon 865
with the Qualcomm X55 5G modem. Two regional versions of the device has been added as connectable to
TEMS Investigation.

• XQ-AT51 (US / EEA / Russia)

• XQ-AT52 (TW / HK / SEA)

• TEMS Connect License: Qualcomm N

17.1.10 Xiaomi Mi 10 Pro 5G M2001J2G

The Xiaomi Mi 10 Pro is a 5G ready Android smartphone based on the Qualcomm Snapdragon 865 chipset and
X55 5G modem.

Supported frequency bands:

• 5G: n1 / n3 / n41 / n78 / n79 (N1 and n3 will be supported after coming firmware updates).

• 4G:

• FDD-LTE: B1 / B2 / B3 / B4 / B5 / B7 / B8 / B12 / B17

• TDD-LTE: B34 / B38 / B39 / B40 / B41

• 3G: WCDMA: B1 / B2 / B4 / B5 / B8

• 2G: GSM: B2 / B3 / B5 / B8

• 4 × 4 MIMO

• TEMS Connect License: Qualcomm N

www.infovista.com | 48
17.2 New Features

17.2.1 HiSilicon chipset support

Devices using the HiSilicon Balong 5000 5G modem can now be connected to and used for network testing in
TEMS Investigation. The Balong 5000 provides industry-leading 5G speeds and supports both NSA and SA
architecture.

TEMS Investigation can do decoding of Layer 3 and Device messages for all available radio technologies,
alongside support for around 50 NR 5G Information Elements and Events, plus basic Information Elements on
legacy technologies.

To use HiSilicon chipset-based devices with TEMS Investigation, a TEMS HiSilicon Connect license must be
acquired.

17.2.2 New NR Information Elements

A few RACH related information elements are now supported by Qualcomm based devices:

• RACH Initial Tx Power

• RACH Current Tx Power

• RACH Number of Transmits

• RACH Latency

17.2.3 Scanning Improvements

A number of valuable improvements has been done for NR scanning. This includes new scanning types, new
information elements and new supported bands.

New Scanning Types:

• NR Signal Scan with L3 Support for Rodhe & Schwarz TSME6

• NR Enhanced Power Scan for PCTEL HBflex, IBflex and MXflex

• NR Spectrum Scan for Rodhe & Schwarz TSME6

• NR Automatic Channel Detection for Rodhe & Schwarz TSME6

• NR Blind Scan for PCTEL HBflex, IBflex and MXflex

New Scanning Information Elements:

• P-SS RSRP, RSRQ and CINR for Rodhe & Schwarz scanners

• Scanned Best Beam, CI, SSS CINR, SSS RP and SSS RQ

Other Scanning Improvements:

• Added support for NR Bands 80, 81, 82, 83, 84 and 86 for PCTEL scanners

• Added support for NR Sub-6GHz Bands n14, n18, n29, n30, n48

• Added support for up to 64 beams on mmWave for PCTEL scanners

www.infovista.com | 49
• Added support for 40 ms SSB periodicity for PCTEL scanners

• Added support for Dynamic Spectrum Sharing (DSS) for PCTEL scanners

17.3 Corrected Bugs

• 00318505 – GLS Reservation Issue

• 00319538 – HBflex requires 5G TI License to use

• 00320657 – Qualcomm MTP/OnePlus Device not displaying RF parameters

• 00323820 – MX-Flex GSM Channels 975-1023 are not measured

• 00321856 – 5G NR Messages and Xiaomi

• 00322644 – Incorrect EN-DC Mode reported

• 00324595 - SINR-PDSCH Carrier 1 not always present

• 00325010 – Incorrect NR Session duration

• 00326020 – Stop script but devices do not stop measuring

17.4 Removed Features

• TD-SCDMA

• RouteDiary

• PESQ Pairing

• PocketPositioningTool

• GSM Channel Verification (Test of TCH)

• Hardware Connect Support for:

• Altair

• Datang

• DRT scanners/transmitters

• Ericsson Mobile Platform (including Ericsson Scanning Unit SRU and Ericsson mobile phones)

• iDEN

• LG chipset

• MTU

• TravelPilot

• Venture scanners

• VIA chipset

www.infovista.com | 50
18 Starting and restarting the TEMS Samsung Galaxy S10
In order to boot the device using the pre-installed TEMS firmware, all models of the Samsung Galaxy S10 must
be started in the following manner:

• Power on by pressing Volume up + Bixby + Power button, release all buttons when the Bootloader warning
is displayed: Started with TEMS firmware, full functionality

If started/restarted in the following manner users can get other results:

• Tapping Restart in the phone menu: Started with Samsung original firmware, no TEMS functionality.

• Power on by pressing Volume up + Bixby + Power button, keep holding all buttons when the Bootloader
warning is displayed: Started in Recovery mode.

Bootloader warning:

To make sure that the device is running TEMS firmware, start the TEMS Status application and verify that TEMS
Command Server is Supported. If not, follow the instructions above to restart the device using TEMS firmware.

www.infovista.com | 51
19 Known Bugs and Limitations

19.1 Device Related

• When running Samsung Shannon based devices with Samsung’s TCP/IP logbank enabled, PDCP DL and
PDSCH Phy Throughput values can be delayed and may arrive after the actual service is finished.

• The procedure to apply an LTE cell lock to the Samsung SM-G960F can be slow and may take up to 1
minute.

• To validate a script containing a Band lock being applied on a Samsung SM-G960F in TEMS Investigation,
the device selected to perform the Band lock must be activated.

• If using the Huawei Mate 20 X 5G EVR-AN00 in GSM or WCDMA networks, voice calls may not be executed
correctly.

19.2 PC Application Related

19.2.1 General

19.2.1.1 TCP Settings

Windows 7 have a function for automatic tuning of TCP settings. Check whether that function is enabled as
follows:

1. Open a Command Prompt using the Run as Administrator option (right-click the Command Prompt item on
the Start menu).

2. Type netsh interface tcp show global and inspect the value returned for Receive Window Auto-Tuning
Level.

3. If this parameter is disabled, give the command netsh interface tcp set global
autotuninglevel=<autotunelevel> to enable it. The value of <autotunelevel> should be “highlyrestricted” if
the server you are contacting does not have RFC1323 implemented or does not support the TCP receive
window scaling factor. Otherwise, <autotunelevel> should have the value “normal”.

19.2.1.2 MTU Size

For LTE operation it may be necessary to adjust the MTU (Maximum Transmission Unit) size, that is, the
maximum IP packet size in bytes. The optimum MTU size depends on the network bandwidth and other factors,
so it is impossible to give a universally valid recommendation. In general, however, the faster the LTE network,
the more important it is to choose a good MTU setting to be able to approach the maximum achievable
throughput.

Here is how to change the MTU size in Windows 7:

4. Open a Command Prompt using the Run as Administrator option (right-click the Command Prompt item on
the Start menu).

5. Run the command netsh interface ipv4 show interfaces and note the identity of the relevant interface.

6. Run the command netsh interface ipv4 set subinterface <interface id from step 2> mtu=<desired MTU
setting> store=persistent.

www.infovista.com | 52
Example: netsh interface ipv4 set subinterface 25 mtu=1360 store=persistent

19.2.2 TEMS Investigation Professional Related

19.2.2.1 Installation and Start-up

• If TEMS™ Investigation takes a long time to start up (more than about 45 seconds), the delay may be caused
by the OS trying unsuccessfully to check the application’s Verisign certificate. If a network has been detected,
the OS will try to contact Verisign to verify that the certificate is not on the Certificate Revocation List (CRL).
TEMS™ Investigation will not continue until this procedure times out.

There are two ways to remedy this:

1. Open up your proxy to enable access to the Certificate Revocation List. The details of how to accomplish
this may vary between countries.

2. Turn off the certificate revocation check in Internet Explorer:

• Open Internet Explorer, and from the Tools menu select Internet Options.

• On the Advanced tab, under Security, uncheck the option “Check for publisher’s certificate
revocation” and click Apply.

(This procedure can be automated by the use of Group Policies.)

• When installing TEMS™ Investigation under Chinese or Japanese Windows, TEMS™ Investigation will not
recognize file paths such as C:\User\<user name>\..., where <user name> contains Chinese or Japanese
characters. This will prevent proper use of the application. (Similar problems may occur with other non-ASCII
characters.)

19.2.2.2 Application Use

• The user manual is missing information about newly added NR 5G Information Elements. Please contact
Infovista support for a full list of information elements.

• When using the Copy Worksheet function, any Map settings will be lost.

• When many devices are used for data collection, the number of windows in the workspace should be kept to
a minimum to lower the CPU load. It is also advisable to start a new logfile recording at least once every hour
in order to reduce RAM consumption.

• During logfile recording as well as during logfile replay, temporary files are created by the application to
enable the user to browse the history of the logfile. These files can become very large (3–4 times the logfile
size), the exact size depending on the number of devices activated in the application at recording time. The
temporary files are named according to the format “temsn” and created in the Windows temp directory
(default: C:\path\tmp, where the path is defined by the environment variable TMP). Make sure there is plenty
of space on the disk where the temp directory resides. The temporary files are removed when you exit the
application; however, if the application terminates abnormally, this might not happen. The files must then be
removed manually.

• Network Connect over RAS fails under Windows 8 and Windows 10 (the IP sniffer does not start).

• Service Control Designer: If multiple Service Control Designers are open simultaneously, a script run from
one of them could fail.

www.infovista.com | 53
• Service Control Designer: Problems may arise during script execution if a participating device is detached
from Windows, whether due to user interaction or to device instability. One thing that may occur in this
situation is duplicate recording of data in multiple logfiles.

• Service Control Designer: The Wait For example in the User’s Manual, section 12.10.6.2 does not work,
since a Wait For activity cannot be triggered by another activity that is inside a (different) while loop.

• Service Control Designer: Running multiple Synchronized Voice Call Sequence snippets (for different
devices) in a Parallel structure does not work. It is necessary to put each such snippet in its own script; the
scripts can then be run concurrently if desired.

• WCDMA SCH timeslot scans are not scriptable.

• When using the serving cell indication in the Map window to show the strongest scanned CPICH, this works
only for the 1st UMTS frequency (the one decoded into the information elements named “1st”).

• The information element “Frequent AQM Score Downlink” is not populated when loading a logfile where
uplink PESQ data has been merged in.

• When doing WhatsApp voice calls, both MT and MO side must run from a TEMS™ Investigation script.
Otherwise the call will fail.

• To replay TEMS Sense or TEMS Voyager logfiles in TEMS Investigation, you need to resynchronize your
Replay license in License Control Center if it was added before upgrading to TEMS Investigation 19.2 or
later.

• The drop-down selections for setting Speech Codec and Codec Rate in the Script designer do not work. To
activate/deactivate a codec/codec rate, double click on the value.

• The HTML Report Generator cannot be started when TEMS Investigation is running. Start the generator by
executing TEMS.Reportgenerator.exe located in the TEMS Investigation program folder from a command
prompt. If the computer has a TEMS Investigation Replay license, add the argument /replay to the command
TEMS.Reportgenerator.exe /replay.

• Serving Cell SSB SNR/Serving Cell SS SNR IE’s will be reported as “Not valid” from Qualcomm devices.

• When performing testing on NR networks, avoid enabling log configurations. If enabled, the recorded logfile
may not have complete NR coverage.

19.2.2.3 Incompatibility with Other Software

• On a PC running Windows 8.1, installing Oracle VM VirtualBox causes TEMS™ Investigation IP sniffing to
fail. However, a workaround is to install VirtualBox without the component “VirtualBox Bridged Networking”.

20 Contact Information
Please visit our website at  www.infovista.com for contact and support information.

www.infovista.com | 54