1.00 2.3.1.A:Clearing and grubbing road land including uprooting 10.

34 Hectare
rank vegetation, grass, bushes, shrubs, saplings and trees
girth up to 300 mm, removal of stumps of trees cut earlier
and disposal of unserviceable materials and stacking of
serviceable material to be used or auctioned, up to a lead of
1000 metres including removal and disposal of top organic
soil not exceeding 150 mm in thickness
In area of light jungle - By Manual Means
1.00 2.1.1:Cutting of trees, including cutting of trunks, branches 230.00 each
and removal of stumps, roots, stacking of serviceable
material with all lifts and up to a lead of 1000 metres and
earth filling in the depression/pit.
Girth from 300 mm to 600 mm
1.00 2.1.2:Cutting of trees, including cutting of trunks, branches 110.00 each
and removal of stumps, roots, stacking of serviceable
material with all lifts and up to a lead of 1000 metres and
earth filling in the depression/pit.
Girth from 600 mm to 900 mm
1.00 3.32:Excavation in soil in hilly area by mechanical means 215857.19 cum
including cutting and trimming of side slopes and disposing
of excavated earth with all lifts and lead upto 1000 metres.

1.00 3.34:Excavation in hilly areas in hard rock requiring blasting, 201.60 cum
by mechanical means including trimming of slopes and
disposal of cut material with all lifts and lead upto 1000
metres.
1.01 3.4:Excavation for roadway in ordinary rock by deploying a 402.50 cum
dozer, 80 HP including cutting and pushing the cut earth to
site of embankment upto a distance of 100 metres ( average
lead 50 metres ), trimming bottom and side slopes in
accordance with the requirements of lines, grades and cross
sections.

1.01 3.16:Construction of embankment with approved material 42364.60 cum

obtained from borrow pits with all lifts and leads, transporting
to site, spreading, grading to required slope and compacting
to meet requirement of table 300-2.

1.01 3.15:Scarifying the existing bituminous road surface to a 4589.20 sqm

depth of 50 mm and disposal of scarified material with in all
lifts and lead upto 1000 metres by Mechanical Means

1.01 4.1.A.1:Construction of granular sub-base by providing 27691.42 cum

graded Material, mixing in a mechanical mix plant at OMC,
carriage of mixed Material to work site, spreading in uniform
layers with a motor grader on the prepared surface and
compacting with vibratory power roller to achieve the desired
density, complete as per clause 401
Grading-I - Plant Mix Method
1.01 4.12:Providing, laying, spreading and compacting graded 34586.15 cum
stone aggregate to Wet Mix Macadam specification including
premixing the Material with water at OMC in mechanical mix
plant carriage of mixed Material by tipper to site, laying in
uniform layers with paver in sub- base / base course on well
prepared surface and compacting with vibratory roller to
achieve the desired density.
1.01 5.1.a:Providing and applying primer coat with bitumen 135007.00 sqm
emulsion ( SS) on prepared surface of granular Base
including clearing of road surface and spraying primer at the
rate of 0.70 - 1.0 kg/sqm using mechanical means.

1.01 5.2.b:Providing and applying tack coat with bitumen 135007.00 sqm
emulsion (RS) using emulsion pressure distributor at the rate
of 0.25 - 0.30 kg per sqm on the prepared Granular Surface
cleaned with mechanical broom.

1.01 5.4.2b:Dense Graded Bituminous Macadam : - For grading - 7412.56 cum

II (26.5 mm nominal size)
Providing and laying dense graded bituminous macadam
with 100-120 TPH batch type HMP producing an average
output of 75 tonnes per hour using crushed aggregates of
specified grading, premixed with a bituminous binder (VG 30)
@ 4.0 to 4.5 percent by weight of total mix and filler,
transporting the hot mix to work site, laying with a hydrostatic
paver finisher with sensor control to the required grade, level,
and alignment, rolling with smooth wheeled, vibratory and
tandem rollers to achieve the desired compaction as per
MoRTH specification clause No. 505 complete in all
respects.
1.01 5.2.a:Providing and applying tack coat with bitumen 135007.00 sqm
emulsion( RS) using emulsion pressure distributor at the rate
of 0.20 - 0.30 kg per sqm on the prepared bituminous
surface cleaned with mechanical broom.
1.01 5.6.2.b:Providing and laying bituminous concrete with 100- 4050.21 cum
120 TPH hot mix plant producing an average output of 75
tonnes per hour using crushed aggregates of specified
grading, premixed with bituminous binder (NRMB) @ 5.4 per
cent of mix and filler, transporting the hot mix to work site,
laying with a hydrostatic paver finisher with sensor control to
the required grade, level and alignment, rolling with smooth
wheeled, vibratory and tandem rollers to achieve the desired
compaction as per MORTH specification clause No. 507
complete in all respects
For Grading -II (13.2 mm Nominal size).
1.02 2.4.2.A:Dismantling of existing structures like culverts, 24.80 cum
bridges, retaining walls and other structure comprising of
masonry, cement concrete, wood work, steel work, including
T&P and scaffolding wherever necessary, sorting the
dismantled material, disposal of unserviceable material and
stacking the serviceable material with all lifts and lead of
1000 metres
Cement Concrete Grade M-15 & M-20 - By Mechanical
Means
1.02 2.4.4.B:Dismantling of existing structures like culverts, 89.48 cum
bridges, retaining walls and other structure comprising of
masonry, cement concrete, wood work, steel work, including
T&P and scaffolding wherever necessary, sorting the
dismantled material, disposal of unserviceable material and
stacking the serviceable material with all lifts and lead of
1000 metres Dismantling Stone Masonry - Rubble stone
masonry in cement mortar.
1.02 3.13.1.B:Earth work in excavation of foundation of structures 19019.63 cum
as per drawing and technical specification, including setting
out, construction of shoring and bracing, removal of stumps
and other deleterious matter, dressing of sides and bottom,
backfilling the excavation earth to the extent required and
utilising the remaining earth locally for road work.
Ordinary soil - Mechanical Means - (Depth upto 3 m)

1.02 12.4:Plain cement concrete 1:3:6 nominal mix in foundation 3065.90 cum
with crushed stone aggregate 40 mm nominal size
mechanically mixed, placed in foundation and compacted by
vibration including curing for 14 days.
1.02 12.8.A.1:Plain/Reinforced Cement Concrete in Open 4911.01 cum
Foundation complete as per Drawing and Technical
Specifications.
PCC Grade M15

1.02 12.8.1.C.1:Plain/Reinforced Cement Concrete in Open 1559.98 cum

Foundation complete as per Drawing and Technical
Specifications
RCC Grade M20 - Using Concrete Mixer
1.02 12.40:Supply, Fitting and Placing un- coated HYSD bar 93.90 MT
Reinforcement in Foundation complete as per Drawing and
Technical Specifications
1.02 13.3:Plastering with cement mortar (1:3 ) on brick work in 2835.63 sqm
sub-structure as per Technical Specifications

1.02 8.8:Painting two coats after filling the surface with synthetic 4515.63 sqm
enamel paint in all shades on new plastered concrete
surfaces
1.02 9.3.A:Laying Reinforced cement concrete pipe NP4 / 31.60 metre
prestressed concrete pipe for culverts on first-class bedding
of granular material in a double row including fixing collar
with cement mortar 1:2 but excluding excavation, protection
works, backfilling, concrete and masonry works in headwalls
and parapets
1000 mm dia
1.03 OD14510/2021-2022:Random Rubble Stone masonry 518.40 cum
(coursed/uncoursed) work in cement mortar 1:6 for
substructure complete as per drawing and Technical
Specifications

1.03 OD14509/2021-2022:Randum Dry Rubble masonary for 17746.00 cum

Protection wall using blasted rubble including wedding them
together with chips, cost , conveyance and all labour charges
etc..complete.

1.03 OD14511/2021-2022:Randum Dry Rubble masonary for 166.60 cum

Protection wall using department stone including wedding
them together with chips, and all labour charges
etc..complete.
1.03 8.13:Providing and laying of hot applied thermoplastic 4867.10 sqm
compound 2.5 mm thick including reflectorising glass beads
on Bituminous Surface @ 250 gms per sqm area, the
thickness of 2.5 mm is exclusive of surface applied glass
beads as per IRC:35. The finished surface to be level,
uniform, and free from streaks and holes.
1.03 8.35:Providing and fixing reflective road studs (Raised 10320.00 no
Pavement Marker) of ' category A' made out of
ASA/HIPS/ABS moulded body with shanks and conforming
to ASTM D 4280, strong enough to support a load of more
than 13.635 T when tested in accordance with ASTM D
4280, reflective panel confirming to ASTM D 788, and
reflectivity conforming to clause 804.4. including installation,
drilling, fixing with adhesive etc. with 2 years warranty for the
road stud as well as for in field performance as per clause
804.7.3 Road Markers/Road Stud with Lense Reflector :-
1.03 8.4.1:Providing and fixing of retro- reflectorised cautionary, 220.00 each
mandatory and informatory sign with 7years warranty
manufactured as per IRC :67 made of Type IV micro
prismatic grade sheeting vide clause 801.3.3 fixed over
aluminum sheeting, 2 mm thick/aluminum composite
material sheeting 4 mm thick with suitable back supporting
frame of MS angle 25x25x3 and supported on GI pipe pole
50mm NB confirming to IS 1239 firmly fixed to the ground by
means of properly designed foundation with M 15 grade
cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm
below ground level including painting all exposed surface
with 2 coats of epoxy painting over epoxy primer and as per
approved drawing and clause 801 including lettering symbols
etc.
90 cm equilateral triangle
1.03 8.4.3:Providing and fixing of retro- reflectorised cautionary, 120.00 each
mandatory and informatory sign with 7years warranty
manufactured as per IRC :67 made of Type IV micro
prismatic grade sheeting vide clause 801.3.3 fixed over
aluminium sheeting, 2 mm thick/ aluminium composit
material sheeting 4 mm thick with suitable back supporting
frame of MS angle 25x25x3 and supported on GI pipe pole
50mm NB confirming to IS 1239 firmly fixed to the ground by
means of properly designed foundation with M 15 grade
cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm
below ground level including painting all exposed surface
with 2 coats of epoxy painting over epoxy primer and as per
approved drawing and clause 801 including lettering symbols
etc.
60 cm circular
1.03 8.4.5:Providing and fixing of retro- reflectorised cautionary, 40.00 each
mandatory and informatory sign with 7years warranty
manufactured as per IRC :67 made of Type IV micro
prismatic grade sheeting vide clause 801.3.3 fixed over
aluminium sheeting, 2 mm thick/ aluminium composit
material sheeting 4 mm thick with suitable back supporting
frame of MS angle 25x25x3 and supported on GI pipe pole
50mm NB confirming to IS 1239 firmly fixed to the ground by
means of properly designed foundation with M 15 grade
cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm
below ground level including painting all exposed surface
with 2 coats of epoxy painting over epoxy primer and as per
approved drawing and clause 801 including lettering symbols
etc.
60 cm x 45 cm rectangular
1.03 8.4.8:Providing and fixing of retro- reflectorised cautionary, 44.00 each
mandatory and informatory sign with 7years warranty
manufactured as per IRC :67 made of Type IV micro
prismatic grade sheeting fixed over aluminium sheeting, 2
mm thick/ aluminium composit material sheeting 4 mm thick
with suitable back supporting frame of MS angle 25x25x3
and supported on GI pipe pole 50mm NB confirming to IS
1239 firmly fixed to the ground by means of properly
designed foundation with M 15 grade cement concrete min
size 45 cm x 45 cm x 60 cm, 60 cm below ground level
including painting all exposed surface with 2 coats of epoxy
painting over epoxy primer and as per approved drawing and
clause 801 including lettering symbols etc.
75 cm octagon
1.03 8.4.12:Providing and fixing of retro- reflectorised cautionary, 340.00 each
mandatory and informatory sign with 7years warranty
manufactured as per IRC :67 made of Type IV micro
prismatic grade sheeting fixed over aluminum sheeting, 2
mm thick/aluminum composite material sheeting 4 mm thick
with suitable back supporting frame of MS angle 25x25x3
and supported on GI pipe pole 50mm NB confirming to IS
1239 firmly fixed to the ground by means of properly
designed foundation with M 15 grade cement concrete min
size 45 cm x 45 cm x 60 cm, 60 cm below ground level
including painting all exposed surface with 2 coats of epoxy
painting over epoxy primer and as per approved drawing and
clause 801 including lettering symbols etc.
50cmx 60 cm rectangular (Single chevron etc.)

1.04 8.5:Providing and fixing of direction and place identification 14.40 sqm
retro-reflectorised sign with 7 years warranty manufactured
as per IRC :67 made of Type IV micro prismatic grade
sheeting fixed over aluminium sheeting, 2 mm thick/
aluminium composit material sheeting 4 mm thick with area
not exceeding 0.9 sqm, with suitable back supporting frame
of MS angle 40x40x6 and supported on GI pipe pole 50mm
NB confirming to IS 1239 firmly fixed to the ground by means
of properly designed foundation with M 15 grade cement
concrete min size 45 cm x 45 cm x 60 cm, 60 cm below
ground level including painting all exposed surface with 2
coats of epoxy painting over epoxy primer and as per
approved drawing and clause 801 including lettering symbols
etc.
1.04 8.6:Providing and fixing of direction and place identification 60.00 sqm
retro-reflectorised sign with 7 years warranty manufactured
as per IRC :67 High Intensity Micro Prismatic (Type IV)
grade sheeting fixed over aluminum sheeting, 2 mm
thick/aluminum composite material sheeting 4 mm thick with
an area exceeding 0.9 sqm, with suitable back supporting
frame of MS angle 40x40x6 and supported on suitably
designed GI pipe pole not less than 50mm NB , 2 Nos.
confirming to IS 1239, firmly fixed to the ground by means of
properly designed foundation with M 15 grade cement
concrete min size 45 cm x 45 cm x 60 cm, 60 cm below
ground level including painting all exposed surface with 2
coats of epoxy painting over epoxy primer and as per
approved drawing and clause 801 including lettering symbols
etc.
1.04 8.16:Reinforced cement concrete M-15 grade boundary 652.00 no
pillars of standard design as per IRC:25-19767, fixed in
position including finishing and lettering but excluding
painting .
1.04 8.1.B:Construction of cement concrete kerb with top and 800.00 metre
bottom width 115 and 165 mm respectively, 325 mm high in
M 20 Grade PCC Using Concrete Batching and Mixing Plant
on M-10 grade foundation 150 mm thick, foundation having
50 mm projection beyond kerb stone, kerb stone laid with
kerb laying machine, foundation concrete laid manually, all
complete as per clause 409
1.04 8.7.A:Providing and erecting overhead signs with retro 2.00 tonne
reflectorised sign with 7 years warranty manufactured as per
IRC67 made of Hign Intensity Micro Prismatic (Type IV )
grade sheeting fixed over corrosion resistant 2mm thick
aluminium alloy sheet with vertical and lateral clearance
given in clause 802.2 and 802.3 and installed as per clause
802.7 over a designed support system of aluminum alloy or
galvanised steel trestles and trusses of sections and type as
per structural design requirements and approved plansTruss
and Vertical Support
1.04 8.7.B:Providing and erecting overhead signs with retro- 13.50 sqm
reflectorised sign with 7 years warranty manufactured as per
IRC :67 made of High Intensity Micro Prismatic (Type IV)
grade sheeting fixed over corrosion resistant 2mm thick
aluminium alloy sheet with vertical and lateral clearance
given in clause 802.2 and 802.3 and installed as per clause
802.7 over a designed support system of aluminium alloy or
galvanised steel trestles and trusses of sections and type as
per structural design requirements and approved plans
Aluminium Alloy Plate for Over Head sign

1.04 8.11.1:Painting lines, dashes, arrows etc on roads in two 20.00 sqm
coats on new work with ready mixed road marking paint
conforming to IS:164 on the bituminous surface, including
cleaning the surface of all dirt, dust and other foreign matter,
demarcation at site and traffic control
Over 10 cm in width
1.04 8.14.1:Reinforced cement concrete M15 grade Kilometre 4.00 each
stone of standard design as per IRC:8-1980, fixing in position
including painting and printing etc.
5th Kilometre stone ( precast)

1.04 8.14.2:Reinforces cement concrete M 15 grade Kilometre 14.00 each

stone of standard design as per IRC:8-1980, fixing in position
including painting and printing etc
Ordinary kilometer stone ( precast)

1.04 8.14.3:Reinforced cement concrete M15 grade Hectometer 68.00 no

stone of standard design as per IRC-8-1980, fixing in
position including painting and printing etc
Hectometer stone (precast)
1.05 8.15:Supplying and installation of delineator (Roadway 200.00 each
indicators) posts 80- 100cm high above ground level, pained
black, and white in 15 cm wide strips, fitted with min. 80 x
100 mm rectangular or 75 mm dia circular retro reflectorized
panels at the top with minimum visibility of 300m with
provisions to prevent edge lifting and vandalisam, and
conforming to clause 806 , IRC-79 and the drawings
including fixing to ground (The deleniator shall be of
approved type as per specification)
1.05 8.20:Providing, Fixing and erecting 50 mm dia GI pipe railing 50.00 RM
in 3 rows duly painted on Tubular Steel Railing on Medium
Weight Steel Channel ( ISMC series) 100 mm x 50 mm, 1.2
metres high above ground, 2 m centre to centre, complete
as per approved drawings including painting over suitable
primer .
1.05 8.23.A:Providing and erecting a "W" metal beam crash 1660.00 metre
barrier comprising of 3 mm thick corrugated sheet metal
beam rail, 70 cm above road/ground level, fixed on ISMC
series channel vertical post, 150 x 75 x 5 mm spaced 2 m
centre to centre, 1.8 m high, 1.1 m below ground/road level,
all steel parts and fitments to be galvanised by hot dip
process, all fittings to conform to IS:1367 and IS:1364, metal
beam rail to be fixed on the vertical post with a spacer of
channel section 150 x 75 x 5 mm, 330 mm long complete as
per clause 811.3
1.05 55.10.1:Providing and erecting retro-reflectorised Object 72.00 each
Hazard Marker 300mm x 900mm Providing and erecting
retro-reflectorised Object Hazard Marker sign with 07 years
warranty, manufactured as per IRC 67 USING Type IV
ASTM D 4956-09 micro prismatic retro reflective sheeting
fixed over aluminium sheetig, 2 mm thick / aluminium
composit material sheeting 4 mm thick with suitable back
support frame and supported on a mild steel angle iron post
75mmx75mmx6mm, firmly fixed 30cm above ground level by
means of properly designed foundation with M 15 grade
cement concrete 30cmx30x45cm, 45cm below ground level
including painting all non-reflective faces with epoxy paint 2
coats over epoxy primer as per approved drawing and clause
801.300 mm x 900 mm

1.05 55.16:Providing and fixing guard post 2000.00 no

Providing and fixing guard post of size 200mmx200mm,
1400mm long, 800mm above ground level and 600mm
below GL. casted in M20 Grade concrete reinforced with 4
nos of 8mm dia longitudinal bars and 6mm dia stirrups @
100mm c/c, firmly fixed in position by means of foundation of
size 0.5mx0.5mx0.7m in M15 grade concrete below ground
level including painting 2 coats on exposed surface with
synthetic enamel paint in alternate white & black band 20cm
wide
1.05 55.14:Providing and fixing retro-reflectorised ceramic 400.00 no
tilesProviding and fixing retro-reflectorised ceramic tiles of
size 10cmX20cm using High Intensity Micro Prismatic (Type
IV) grade sheeting with 7 years warranty fixed over Ist
quality ceramic glazed tiles including cost of glue, cutting
charges, fixing with suitable adhisive on concrete or other
surface etc complete.
1.05 55.23:Supplying and laying interlocking tile 80mm or nearest 150.00 sqm
size thickness, minimum strength M30 including providing a
layer of 6mm aggregate for 5cm thickness, then laying
interlock cobbles in lines and levels as per the directions of
the departmental officers at site inclusive of all cost &
conveyance charges etc. complete.
1.05 11.2.1:Grassing with 'Doobs' grass including watering and 175.00 sqm
maintenance of the lawn for 30 days or more till the grass
forms a thick lawn free from weeds and fit for moving
including supplying good earth if needed
In rows 15 cm apart in either direction