QM 07 - QM 08 - Valves and Fittings Questions
Uploaded by
mohamed elmasryQM 07 - QM 08 - Valves and Fittings Questions
Uploaded by
mohamed elmasryValves and Fittings Questions
1. List the required leak tests for gate valves per API-598 requirements?
2. Is sealant allowed to be used during the seat leak tests?
3. What is normally meant by the term "valve trim"?
4. What is NACE MR0175?
5. According to NACE MR0175 what is the normal maximum hardness of
carbon and low alloy steels exposed to sour service?
6. Is hydrostatic shell tests of valves acceptable after painting?
7. What is the difference between a valve that is manufactured to ASTM
A216 WCB and one that is ASTM A105 specifications?
8. In addition to hardness testing, what is the other main requirement in
NACE MR0175?9.
9. What are the normal flange ratings of ANSI valves?
10. What National Code governs pressure/safety relief valves?
11. In regards to relief valves, what is a pop test ?
12. In regards to relief valves, what is a blowdown test ?
13. What test media are acceptable for pressure testing?
14. Which type of valve allows the greatest seat leakage, resilient or metal
seats?
15. What is the purpose of a backseat on a gate valve?
16. What characteristics would you check during a dimensional inspection of a
valve?
17. In what position must the closure device be in when performing a shell
hydrostatic test?
18. How would you measure raised face finish?
19. In relation to working pressure, at what pressure is a shell hydrostatic test
performed (in accordance with ANSI B16.5)?
20. TRUE or FALSE: Allowable seat leakage is greater for a check valve than
for a gate valve of the same size.
21. TRUE or FALSE: Allowable seat leakage is lower for a metal sealed valve
than for a soft seat valve.
22. Name two materials commonly used for soft seat inserts in a valve seat
ring.
23. Which relief valve components are hydrostatically tested?
24. Describe a control valve hysteresis test.
25. What is the position of a gate during a backseat test?
26. TRUE OR FALSE: The packing gland should be tight during the backseat
test.
27. Is leakage permitted on a backseat test of a gate valve?
28. Which of the following industry standards, relating to valves, gives
radiographic quality standards: for steel castings? a) ANSI B.16.5 b)
MSS-SP-54 c) ASME Section V d) API 6A
29. Which of the following industry standards, relating to valves, gives visual
inspection quality standards for steel castings? a) ANSI B.16.5 b)
MSS-SP-55 c) ASME Section V d) ASNT-TC-1A
30. What is the standard type of finish on raised face flanges?
31. What information should be stamped on a buttweld fitting?
32. What is the normal depth an imperfection become injurious in a buttweld
fitting?
33. What nondestructive examination would you expect to have been
performed on a 36" diameter elbow?
34. What characteristics would you check during a dimensional inspection of a
flange?
35. What is the purpose of spot or back facing on flange bolt holes?
36. What additional mechanical test is done a materials for low temperature
service?
37. Name the common ASTM standard used for the manufacture of wrought
steel buttwelding fittings.
38. At what pressure is the standard low pressure air seat test performed on
valves?
39. In relation to working pressure, at what pressure is a shell high pressure
seat test generally performed
40. Name the common test for checking holidays in nickel plating.
41. What are the three basic body styles of ball valves?
42. TRUE or FALSE: Industry standards typically require hydrostatic testing of
fittings at the fitting fabricator.
43. What type of water is typically required for pressure testing of austenitic
stainless steel valves ?
44. TRUE or FALSE: Shell and backseat tests are required for Gate Valves,
Globe Valves and Check Valves.
45. List 3 types of flanges.
46. Name four types of shutoff valves.
47. What is an advantage of using a flexible wedge instead of a solid wedge?
48. List three different types of wedges mentioned in API 600.
49. Name at least three items/attributes that are normally mentioned in a
valve pressure testing report.
50. What is the maximal allowable leakage rate in drops of a 24" soft seated
ball valve?
51. What is a stopple fitting used for?
52. What is a hottap?
53. What kind of valve material is used when valves are in high temperature
service?
54. What is the hydrotest sequence for an internal coated valves?
55. Why do you do a seat test on both sides of a ball or gate valve?
56. Which API Specification covers flanged steel safety relief valves?
57. Which American standard covers Face to Face an End to End Dimensions
of valves?
58. In which American standard can you find the acceptable leakage rates for
control valve seat leakage?
59. The Term Cv as related to control valves represents: a) Correction factor
for viscosity b) Controlled variable c) Valve Flow Coefficient d)
Check Valve
60. Should you specify a "jam style" or a "spring-loaded" packing
arrangement for a sliding stem control valve selected for NACE MR0175
service?
2 of 3
61. What would be the most likely stem packing material for a sliding stem
control valve selected for NACE MR0175 service, if the temperature was
bellow 400 F?
62. Name at least three types of control valves.
63. Name five main components of a Control valve body?
64. Name five main components of the valve actuator.
65. Name two common types of control valve trims.
3 of 3
