Yamaha MG24 14fx Service Manual
Yamaha MG24 14fx Service Manual
MG32/14FX
MIXING CONSOLE
SERVICE MANUAL
MG32/14FX MG24/14FX
CONTENTS (目次)
SPECIFICATIONS(総合仕様)................................................ 3/5
DIMENSIONS(寸法図)............................................................ 7
PANEL LAYOUT(パネルレイアウト)..................................... 8
CIRCUIT BOARD LAYOUT(ユニットレイアウト)................ 17
WIRING(結線図).................................................................. 18
DISASSEMBLY PROCEDURE(MG24/14FX分解手順)........ 23
DISASSEMBLY PROCEDURE(MG32/14FX分解手順)........ 35
LSI PIN DESCRIPTION(LSI端子機能表)............................... 47
IC BLOCK DIAGRAM(ICブロック図).................................. 50
CIRCUIT BOARDS(シート基板図)....................................... 51
INSPECTIONS(検査)....................................................... 65/72
PARTS LIST
BLOCK DIAGRAM & LEVEL DIAGRAM
(ブロックダイアグラム&レベルダイアグラム)
OVERALL CIRCUIT DIAGRAM(総回路図)
WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in per-
sonal injury, destruction of expensive components and failure of the product to perform as specified. For
these reasons, we advise all Yamaha product owners that all service required should be performed by an
authorized Yamaha Retailer or the appointed service representative.
IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-
cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of
any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and
service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable
and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to
exist, please contact the distributor’s Service Division.
WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to
this bus.)
IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power
to the unit.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT
SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling
food.
WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those
originally installed.
印の部品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部品をご使用ください。
SPECIFICATIONS
General Specifications
Frequency Characteristics (Master Output) 20 Hz–20 kHz +1 dB, –3 dB @+4 dBu, 600 Ω (with gain control at minimum level)
Total Harmonic Distortion (Master Output) <
= 0.1% (THD+N) @+14 dBu, 20 Hz–20 kHz, 600 Ω (with gain control at maximum level)
–128 dBu Equivalent input noise (CHs 1 to 24 (MG32/14FX)/CHs 1 to 16 (MG24/14FX))
Hum and Noise (20 Hz - 20 kHz) 1 –99 dBu Residual output noise (ST, MONO OUT, AUX, EFFECT, GROUP OUT)
Input GAIN = Maximum –83 dBu (87 dB S/N) ST, MONO, GROUP Master fader at nominal level; all Ch assign switches off.
Input PAD = OFF –78 dBu (82 dB S/N) AUX master control at nominal level; all channel mix controls at minimum level.
Input sensitivity = –60 dBu ST, GROUP Master fader and one Ch fader at nominal level.
–64 dBu (68 dB S/N)
(CHs 1 to 24 (MG32/14FX)/CHs 1 to 16 (MG24/14FX))
60 dB CH IN → CH INSERT OUT
84 dB CH IN → GROUP OUT/ST OUT (CH to ST)
94 dB CH IN → ST OUT (GROUP to ST)
70 dB CH IN → GROUP INSER OUT, ST INSERT OUT (CH to ST)
62.2 dB CH IN → REC OUT (CH to ST)
76 dB CH IN → AUX SEND (PRE)
86 dB CH IN → AUX SEND (POST)/EFF SEND
Maximum Voltage Gain 2 80 dB CH IN → ST SUB OUT (CH to ST)
58 dB ST CH IN → GROUP OUT/ST OUT (ST CH to ST)
47 dB ST CH IN → AUX SEND (PRE)
57 dB ST CH IN → AUX SEND (POST)/EFF SEND
16 dB RETURN → ST OUT
9 dB RETURN → AUX SEND
27.8 dB 2TR INPUT → ST OUT
Monaural/Stereo Input Gain Control 44 dB variable
Monaural High Pass Filter 80 Hz 12 dB/octave
Channel Input PAD 0 dB/26 dB
–70 dB between input channels
Crosstalk (1 kHz)
–70 dB between input/output channels (CH INPUT)
Monaural Input Channel Equalization: ±15 dB HIGH 10 kHz shelving
MID 0.25–5 kHz peaking
Max. Variation (CHs 1 to 8) 3 LOW 100 Hz shelving
±15 dB HIGH 10 kHz shelving
Stereo Input Channel Equalization: HI-MID 3 kHz peaking
Max. Variation (CHs 9/10 to 15/16) 3 LO-MID 800 Hz peaking
LOW 100 Hz shelving
Effect 1: 16 programs, parameter control
Internal Digital Effects Effect 2: 16 programs, parameter control
TAP DELAY Control, Foot Switch (TAP)
MONO Low Pass Filter 80 - 120 Hz 12 dB/octave
Monaural/Stereo Input Peak Indicator One red LED per channel. Comes on when post-EQ signal level reaches +17 dBu.
Monaural/Stereo Input Signal Indicator One green LED per channel. Comes on when post-EQ signal level reaches –10 dBu.
Four 12-point LED meters [Stereo (L, R), PFL/AFL, GROUP (1 - 4)]
Peak point: red indicator
Level Meters
+5, +3, +1, and 0 points: yellow indicators
–1, –3, –5, –7, –10, –15, –20: green indicators
Phantom +48 VDC Power +48 V DC supply to balanced inputs. Can be switched ON/OFF in groups of eight channels.
(Balanced input) (One switch for every eight channels.)
Included Accessory Power cord, Owner’s Manual
Option FC5 (Foot Switch)
Lamp XLR-3-31 type (12 V AC between pins 2 and 3; 0.5 A max. rating )
USA and Canada: 120 V AC, 60 Hz
Power Supply Korea: 220 V AC, 60 Hz
Others: 230 V AC, 50 Hz
Power Consumption MG32/14FX: 120 W, MG24/14FX: 100 W
Max. Dimensions (W × H × D) MG32/14FX: 1027 × 140 × 551 mm, MG24/14FX: 819 × 140 × 551 mm
Weight MG32/14FX: 22 kg, MG24/14FX: 18.5 kg
Input Specifications
TALK BACK 10 kΩ 50 - 600 Ω –66 dBu –50 dBu –30 dBu XLR-3-31 type
mic (0.388 mV) (2.45 mV) (24.5 mV) (unbalanced)
Output Specifications
ST OUT (L, R) 150 Ω 600 Ω line +4 dBu (1.23 V) +24 dBu (12.3 V) XLR-3-32 type (balanced)
MONO
REC OUT (L, R) 600 Ω 10 kΩ line –10 dBV (316 mV) +10 dBV (3.16 V) RCA pin jack
CH INSERT OUT
(MG32/14FX: CH 1- 24)
(MG24/14FX: CH 1- 16) Phone jack (TRS)
150 Ω 10 kΩ line 0 dBu (0.775 V) +20 dBu (7.75 V)
(unbalanced [T: out; R: in; S: ground])
GROUP INSERT OUT
(1-4)
ST INSERT OUT (L, R)
総合仕様
一般仕様
周波数特性(Master Output) 20 Hz ∼ 20 kHz +1 dB、–3 dB @+4 dBu(*)、600 Ω(GAIN コントロール=最小レベル)
全高調波歪率(Master Output) <
= 0.1 %(THD+N)@+14 dBu、20 Hz ∼ 20 kHz、600 Ω(GAIN コントロール=最大レベル)
–128 dBu 入力換算ノイズ(CH1 ∼ 24(MG32/14FX) / CH1 ∼ 16( MG24/14FX))
–99 dBu 残留ノイズ(ST、MONO OUT、AUX、EFFECT、GROUP OUT)
–83 dBu ST、MONO、GROUP
ハム & ノイズ(20 Hz~20 kHz)*1
(87 dB S/N) マスターフェーダー=ノミナル、全チャンネルアサインスイッチ= OFF
Input GAIN = Maximum
Input PAD = OFF –78 dBu AUX マスターコントロール=ノミナル、全チャンネル
Input sensitivity = –60 dBu (82 dB S/N) ミックスコントロール=最小レベル
ST、GROUP
–64 dBu
マスターフェーダー& 1 チャンネルフェーダー=ノミナル
(68 dB S/N)
(CH1 ∼ 24(MG32/14FX) / CH1 ∼ 16(MG24/14FX))
60 dB CH IN → CH INSERT OUT
84 dB CH IN → GROUP OUT/ST OUT(CH to ST)
94 dB CH IN → ST OUT(GROUP to ST)
70 dB CH IN → GROUP INSERT OUT、ST INSERT OUT(CH to ST)
62.2 dB CH IN → REC OUT(CH to ST)
76 dB CH IN → AUX SEND(PRE)
86 dB CH IN → AUX SEND(POST)/EFF SEND
最大電圧ゲイン *2
80 dB CH IN → ST SUB OUT(CH to ST)
58 dB ST CH IN → GROUP OUT/ST OUT(ST CH to ST)
47 dB ST CH IN → AUX SEND(PRE)
57 dB ST CH IN → AUX SEND(POST)/EFF SEND
16 dB RETURN → ST OUT
9 dB RETURN → AUX SEND
27.8 dB 2TR IN → ST OUT
モノラル、ステレオインプットゲインコントロール 44 dB 可変
モノラルハイパスフィルター 80 Hz 12 dB/octave
チャンネル入力 PAD 0 dB/26 dB
–70 dB 入力チャンネル間
クロストーク(1 kHz)
–70 dB 入出力チャンネル間(CH INPUT)
±15 dB HIGH 10 kHz シェルビングタイプ
モノラル入力チャンネルイコライザー特性最大可
MID 0.25 ∼ 5 kHz ピーキングタイプ
変幅(CH1 ∼ 8)*3 LOW 100 Hz シェルビングタイプ
±15 dB HIGH 10 kHz シェルビングタイプ
ステレオ入力チャンネルイコライザー特性最大可 HI-MID 3 kHz ピーキングタイプ
変幅(CH9/10 ∼ 15/16)*3 LO-MID 800 Hz ピーキングタイプ
LOW 100 Hz シェルビングタイプ
エフェクト 1: 16 種類、パラメーターコントロール
内蔵デジタルエフェクト エフェクト 2: 16 種類、パラメーターコントロール、
TAP DELAY コントロール、フットスイッチ (TAP)
MONO ローパスフィルター 80 ∼ 120 Hz 12 dB/octave
モノラル、ステレオインプットピークインジケーター 各チャンネル、イコライザーの後段において、信号レベルが +17 dBu に達すると赤く点灯
モノラル、ステレオインプットシグナルインジケーター 各チャンネル、イコライザーの後段において、信号レベルが –10 dBu に達すると緑に点灯
12 ポイント LED × 4 [ステレオ(L、R) 、 PFL/AFL、GROUP(1~4)]
ピーク時:赤のインジケーター
レベルメーター +5、+3、+1、0:黄のインジケーター
–1、 –3、–5、–7、–10、–15、–20:緑のインジケーター
ファンタム電源 +48 VDC(バランス入力) PHANTOM +48 V スイッチ= ON で 8 チャネルごとに供給
付属品 電源コード、取扱説明書、保証書
オプション FC5(フットスイッチ)
ランプ端子 XLR-3-31 type(2-3 pin 間に AC12 Vを供給、最大定格 0.5 A)
電源 100 V AC 50/60 Hz
消費電力 MG32/14FX:120 W、 MG24/14FX:100 W
最大外形寸法(W × H × D) MG32/14FX:W1027 × H140 × D551 mm、MG24/14FX:W819 × H140 × D551 mm
質量 MG32/14FX:22 kg、MG24/14FX:18.5 kg
* 0 dBu=0.775V、 0 dBV=1 V とする
*1 Rs=150 ohms
@12.7 kHz、–6 dB/oct. のローパスフィルターにて測定(@20 kHz、–∞ dB/oct.フィルターに相当)
*2 PAN/BAL 左か右へ回す
*3 シェルビングタイプのターンオーバー/ロールオフ周波数:最大可変幅に対し3 dB下 がったポイント
入力仕様
入力イン 適合 最大ノンク
入力端子名称 PAD ゲイン 感度 *1 規定レベル 端子仕様
ピーダンス インピーダンス リップレベル
CH INPUT(A、B) 3 kΩ 50 ∼ 600 Ω –80 dBu –60 dBu –40 dBu A:XLR-3-31タイプ
0
(MG32/14FX:CH1 ∼ 24) マイク (0.078 mV)( 0.775 mV)(7.75 mV) (バランス型)
–60
(MG24/14FX:CH1 ∼ 16) 600 Ω ライン –54 dBu –34 dBu –14 dBu B: フォーンジャック
26
(1.55 mV) ( 15.5 mV) (155 mV) (TRS)
–36 dBu –16 dBu +4 dBu (バランス型
0 [T:ホット、R: コール
(12.3 mV) ( 123 mV) (1.23 V)
–16 ド、S:グラウンド] )
–10 dBu +10 dBu +30 dBu
26
(245 mV) ( 2.45 V) (24.5 V)
ST CH INPUT 10 kΩ 600 Ω ライン –54 dBu –34 dBu –14 dBu フォーンジャック
–34
(MG32/14FX:CH25(L)/26(R) (1.55 mV) ( 15.5 mV) (155 mV) (アンバランス型)
∼ CH31(L)/32(R)) –10 dBu +10 dBu +30 dBu RCA ピックジャック *2
(MG24/14FX:CH17(L)/18(R) +10 (245 mV) ( 2.45 V) (24.5 V)
∼ CH23(L)/24(R))
ST INSERT IN [L、R] 10 kΩ 600 Ω ライン –10 dBu 0 dBu +20 dBu フォーンジャック(TRS)
GROUP INSERT IN(1~4) (245 mV) ( 0.775V) (7.75 V) (アンバランス型
CH INSERT IN –20 dBu 0 dBu +20 dBu [T:アウト、R:イン、
10 kΩ 600 Ω ライン
(MG32/14FX:CH1 ∼ 24) (77.5 mV) ( 0.775 V) (7.75 V) S:グラウンド])
(MG24/14FX:CH1 ∼ 16)
RETURN (1、2) (L、R) 10 kΩ 600 Ω ライン –12 dBu +4 dBu +24 dBu フォーンジャック(TRS)
(195 mV) ( 1.23 V) (12.3 V) (アンバランス型)
TALK BACK 10 kΩ 50 ∼ 600 Ω –66 dBu –50 dBu –30 dBu XLR-3-31 タイプ
マイク (0.388 mV)( 2.45 mV) (24.5 mV) (アンバランス型)
2TR IN (L、R) 10 kΩ 600 Ω ライン –26 dBV –10 dBV +10 dBV RCA ピンジャック
(50.1 mV) ( 316 mV) (3.16 V)
* 0 dBu=0.775 V、 0 dBV=1 V とする
*1
入力感度:最大ゲイン測定時に定格出力が得られる最小レベル
*2 MG32/14FX: CH29(L)/30(R)、CH31(L)/32(R)、MG24/14FX: CH21(L)/22(R)、CH23(L)/24(R)
出力仕様
出力 適合 最大
出力端子名称 規定レベル 端子仕様
インピーダンス インピーダンス ノンクリップレベル
ST OUT(L、R) 150 Ω 600 Ω ライン +4 dBu( 1.23 V) +24 dBu(12.3 V) XLR-3-32 タイプ(バランス型)
MONO
GROUP OUT(1 ∼ 4) 150 Ω 600 Ω ライン +4 dBu( 1.23 V) +20 dBu(7.75 V) フォーンジャック(TRS)
AUX SEND(1 ∼ 6) (インピーダンスバランス型
[T:ホット、R: コールド、
S: グラウンド])
REC OUT(L、R) 600 Ω 10 kΩ ライン –10 dBV(316 mV) +10 dBV(3.16 V) RCA ピンジャック
DIMENSIONS(寸法図)
MG32/14FX
1027 140
48
415
551
Units: mm
(単位)
MG24/14FX
819 140
48
415
551
Units: mm
(単位)
PANEL LAYOUT(パネルレイアウト)
7 6 5
Front Panel(フロントパネル)
11
10
1 2 4 3
Note: Within this manual, all panel illustrations show the MG32/14FX panel.
(本書中のイラストはすべてMG32/14FXです。)
Rear Panel(リアパネル)
13 12
1 [PAD] Switch
2 [GAIN] Control
3 [ 80 ] Switch (High-Pass Filter)
4 [Equalizer] Controls
5 [AUX] Controls ([AUX1] to [AUX6])
6 [PRE] Switch
7 [EFFECT] Controls
8 [AUX5], [AUX6] Switch
9 [PAN] Control (Monaural Channels)
[BAL] Control (Stereo Channels)
10 [ON] Switch
11 [PFL] (Pre-Fader Listen) Switch
12 [PEAK] indicator
13 [SIGNAL] indicator
14 [GROUP] Switches
15 [ST] Switch
16 [Channel] Fader
17 [PHANTOM +48 V] Switch
1 [PAD] スイッチ
2 [GAIN] コントロール
3 [ 80 (ハイパスフィルター)スイッチ
]
4 [イコライザー] コントロール
5 [AUX] コントロール([AUX1] ∼[AUX6] )
6 [PRE] スイッチ
7 [EFFECT] コントロール
8 [AUX5] 、[AUX6] スイッチ
9 [PAN] コントロール(モノラルチャンネル)
[BAL] コントロール(ステレオチャンネル)
10 [ON] スイッチ
11 [PFL] スイッチ(Pre‐ Fader Listen )
12 [PEAK] インジケーター
13 [SIGNAL] インジケーター
14 [GROUP] スイッチ
15 [ST] スイッチ
16 [チャンネル] フェーダー
17 [PHANTOM +48 V] スイッチ
1 [PAN] Control
2 [TO ST] Switches
3 [AFL] (After-Fader Listen) Switches
4 [Group] Faders
1 [PAN] コントロール
2 [TO ST] スイッチ
3 [AFL] スイッチ(After‐ Fader Listen)
4 [GROUP] フェーダー(1 ∼ 4)
10
1 [AUX] ミックスコントロール(1 ∼ 4)
2 [ST] コントロール
3 [PFL] スイッチ(Pre‐Fader Listen)
11
1 [PROGRAM] Dials
2 [PARAMETER] Controls
3 [AUX PRE] Controls ([AUX1] to [AUX4])
4 [TAP] Button and Indicator
5 [ON] Switches
6 [PFL] (Pre-Fader Listen) Switches
7 [GROUP] Switches
8 [ST] Switches
9 [EFFECT RTN] faders (1, 2)
12
1 [POWER] Indicator
2 [STEREO Level] Meters
3 [PFL-AFL Level] Meters
4 [GROUP] Switch
5 [PHONES] Jack and Control
1 [POWER] インジケーター
2 [STEREO] レベルメーター
3 [PFL‐AFL] レベルメーター
4 [GROUP] スイッチ
5 [PHONES]
13
[LAMP] Jack
[LAMP] 端子
1 [MIC] Jack
2 [Talkback] Control
3 [AUX1] - [AUX4] Switch
4 [ST] Switch
1 [MIC] 端子
2 [トークバック] コントロール
3 [AUX] スイッチ([AUX1] ∼[AUX4])
4 [ST] スイッチ
14
15
Connector Polarities
INPUT OUTPUT
Pin 1: Ground
INPUT A, ST OUT, MONO Pin 2: Hot (+)
Pin 3: Cold (–)
INPUT
Pin 1: Ground
MIC (Talkback) Pin 2: Hot (+)
Pin 3: Ground
*These jacks also accept connection to monaural phone plugs. If you use monaural plugs, the connection will be unbalanced.
端子接続の極性
INPUT OUTPUT
ピン 1:グラウンド
INPUT A、ST OUT、MONO ピン 2:ホット(+)
ピン 3:コールド(–)
INPUT
ピン 1:グラウンド
MIC(トークバック) ピン 2:ホット(+)
ピン 3:グラウンド
チップ:ホット(+)
INPUT B、GROUP OUT、AUX SEND (1 ∼ 6)、
リング:コールド(–)
EFF SEND(1、2)、ST SUB OUT( * )
スリーブ:グラウンド リング
チップ:Output
INSERT I/O、
リング:Input
GROUP INS I/O、ST INSERT I/O
スリーブ:グラウンド
スリーブ チップ
チップ:L
PHONES リング:R
スリーブ:グラウンド
ステレオチャンネル入力端子、
RETURN(1、2)
スリーブ チップ
チップ:ホット
スリーブ:グラウンド
ステレオチャンネル入力端子、
2TR IN、
REC OUT スリーブ チップ
(*) これらの端子に、モノラルタイプのフォーン端子を使用することもできます。その場合は、アンバランスになります。
16
MG32/14FX
MAS 3/4
MAS 4/4
MG24/14FX
MAS 3/4
MAS 4/4
17
WIRING(結線図)
MG32/14FX CN107
INJK CN108 CN110
CN101 CN101
(INJK1)
CN105 CN105
CN102 CN102
1ch
~
8ch
IN (IN1)
CN103 CN103
CN104 CN104
CN109 CN111
CN106
CN107
INJK CN108 CN110
CN101 CN101
(INJK2)
CN105 CN105
CN102 CN102
9ch
IN (IN2)
~
16ch
CN103 CN103
CN104 CN104
CN109 CN111
CN106
CN107
INJK CN108 CN110
CN101 CN101
(INJK3)
CN105 CN105
CN102 CN102
17ch
IN (IN3)
~
24ch
CN103 CN103
CN104 CN104
CN109 CN111
CN106
CN903
MASJK CN301 CN302
CN904
CN905
25ch
~
DSP
CN201 CN501 CN503
18
MG24/14FX INJK
CN107
CN108 CN110
CN101 CN101
(INJK1)
CN105 CN105
CN102 CN102
1ch
~ IN (IN1)
8ch
CN103 CN103
CN104 CN104
CN109 CN111
CN106
CN107
INJK CN108 CN110
CN101 CN101
(INJK2)
CN105 CN105
CN102 CN102
9ch
IN (IN2)
~
16ch
CN103 CN103
CN104 CN104
CN109 CN111
CN106
CN903
MASJK CN301 CN302
CN904
CN905
CN101 CN101
DSP
CN201 CN501 CN503
17ch
~
19
4
2
7 260:WA609600 250: (WA60980)
6
280:VV314800 190:WA782600
5
3
230:VP184000
3 3
915:WB071100
270: (WA61030)
※
two turn
15mm ± 2mm
15mm ± 2mm
210:WA677500
20
3-1. Connect wire of circuit-board MAS1000 and IN1000 4-1. Connect wire of circuit-board MASJK1000 and INJK1000
(MAS1000シートとIN1000シートの結線) (MASJK1000シートとINJK1000シートの結線)
90, 150:WB349900 80, 140:WB349800
420, 600:WB349700
430, 610:WB349600
900:WA786300
20mm ± 5mm
21
6-2. Bundle secondary wire of trans and wire WA69740:PH-SAN-2P 7-1. Assembly of circuit-board PS1000 and HEAT-SINK with silicon grease.
(トランスおよびワイヤーWA69740:HP-SAN-2Pの第2ワイヤーの束) (シリコングリスを備えたPS1000シートおよびヒートシンクAss'y)
heat-sink
830: (WA67590)
905:VV104600
silicon grease(シリコングリス)
DB200,IC300,IC400,IC500,TR400,
IC200,IC201,IC202,IC203
22
[980]: Bind Head Tapping Screw-B(+バインドBタイト) [1000]: Bind Head Tapping Screw-B(+バインドBタイト)
4.0X20 MFZN2BL (VS205900) 4.0X20 MFZN2BL (VS205900)
• Bottom view
[930] [940] [930] [940] Bottom cover(ボトムカバー)
[930]
[930]
[940]
[930]
[930]
[930]
Photo.3 (写真3)
23
[700]
[710]
Side cover L
(サイドカバーL)
[700]
[700]: Hex. Socket Set Screw(六角穴付きSタイト) [710]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (V9842300) 3.0X6 MFZN2BL (EP630210)
[730]
[740]
Side cover R
(サイドカバーR)
[730]
[730]: Hex. Socket Set Screw(六角穴付きSタイト) [740]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (V9842300) 3.0X6 MFZN2BL (EP630210)
24
4. Supports 4. 台
4-1 When you work on the back of the top cover, set the 4-1 トップカバーの裏面の作業をする時、そのまま作業
supports to the right and left sides to prevent the すると基板がゆがんでしまうので、トップカバー裏
circuit boards from being distorted. (Photo.8) 面の作業をする時は、左右に台を当ててください。
(写真 8)
Supports
(台)
Photo.8 (写真8)
25
Bolt Nut(ナット)
(ボルト) [B]
[A]
[880]
Photo.9 (写真9)
[850] PS
[840]
[840]
Photo.11 (写真11)
26
[800] [780]
[800]: Bind Head Tapping Screw-S(+バインドSタイト) [780]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (EP630210) 3.0X6 MFZN2BL (EP630210)
[760]
Photo.14 (写真14)
27
[200]
Power switch
knob
(PSWノブ) Claw
(ツメ)
[220]
AC-IN connector(ACインレット)
[240]
PS holder(PSホルダー)
Push switch(プッシュSW)
Photo.17 (写真17)
28
Photo.18 (写真18)
Hexagonal nut and flat washer [A] Hexagonal nut and flat washer [B]
(特殊六角ナットと平ワッシャ[A]) (特殊六角ナットと平ワッシャ[B])
29
Photo.21 (写真21)
30
Photo.22 (写真22)
IN 2 IN 1 IN 2 IN 1
(フック)
Hooks
(フック)
Hooks
Photo.23(写真23) 31
Photo.25 (写真25)
14. MAS 1/4 to 4/4 Circuit Boards 14. MAS 1/4 ∼ 4/4 シート
(Time required: About 15 minutes) 14-1 ボトムカバーを外します。 (1 項参照)
14-1 Remove the bottom cover. (See procedure 1.) 14-2 台を当てます。 (4 項参照)
14-2 Set the supports. (See procedure 4.) 14-3 ヒートシンクを外します。 (5-3 項参照)
14-3 Remove the heat sink. (See procedure 5-3.) 14-4 DSP シールドベースを外します。 (8 項参照)
14-4 Remove the DSP shield base. (See procedure 8.) 14-5 MAS 2/4:
(所要時間:約 7 分)
14-5 MAS 2/4: (Time required: About 7 minutes) 14-5-1 コントロールパネル面から、 [390A]のネジ 2 本を外
14-5-1 Remove the two (2) screws marked [390A] from the して、MAS 2/4 シートを外します。 (写真 26、29)
control panel surface. Then, remove the MAS 2/4 14-6 MAS 3/4: (所要時間:約 7 分)
circuit board. (Photo.26, 29) 14-6-1 コントロールパネル面から、 [390B]のネジ 2 本を外
14-6 MAS 3/4: (Time required: About 7 minutes) し、MAS 3/4 シートを外します。 (写真 26、29)
14-6-1 Remove the two (2) screws marked [390B] from the 14-7 MAS 4/4: (所要時間:約 7 分)
control panel surface. Then, remove the MAS 3/4 14-7-1 [D]の特殊六角ナットと平ワッシャ1個を外し、MAS
circuit board. (Photo.26, 29) 4/4 シートと基板固定金具を外します。
14-7 MAS 4/4: (Time required: About 7 minutes) (写真 26、29、30)
14-7-1 Remove the hexagonal nut and flat washer [D] from 14-8 MAS 1/4: (所要時間:約 12 分)
the control panel surface.Then, remove the MAS 4/4 14-8-1 サイドパッド R を外します。(1 項参照)
circuit board. (Photo.26, 29, 30) 14-8-2 コントロールパネル面から、ノブ(FADER) 12 個と
14-8 MAS 1/4: (Time required: About 12 minutes) ノブ (SELECT)2 個を外します。(写真 26)
14-8-1 Remove the side pad R. (See procedure 1.) 14-8-3 MAS 2/4 シートを外します。 (14-5 項参照)
14-8-2 Remove the twelve (12) fader knobs and the two (2) 14-8-4 MAS 3/4 シートを外します。 (14-6 項参照)
select knobs from the control panel surface. 14-8-5 MAS 4/4 シートを外します。 (14-7 項参照)
(Photo.26) 14-8-6 [380]のネジ 4 本を外します。 (写真 29)
14-8-3 Remove the MAS 2/4 circuit board. 14-8-7 MAS 1/4 シートを固定しているフック 24 箇所を
(See procedure 14-5.) まっすぐになるようにひねり、MAS 1/4 シートを
14-8-4 Remove the MAS 3/4 circuit board. 外します。 (写真 29)
(See procedure 14-6.)
14-8-5 Remove the MAS 4/4 circuit board.
(See procedure 14-7.)
14-8-6 Remove the four (4) screws marked [380]. (Photo.29)
14-8-7 Twist the twenty-four (24) hooks of the MAS 1/4
circuit board to become straight. Then, remove the
MAS 1/4, 3/4, and 4/4 circuit boards. (Photo.29)
32
The meter reflector, push ON buttons, sleeve ON ※ MAS 1/4 シート上のリフレクター METER、ボタン
buttons, push PFL buttons, holder circuit board, ON Ass’y、スリーブ ON ボタン、ボタン PFL、基
volume knobs, push HPF buttons, push TAP 板固定金具、ノブ(VR) 、ボタン HPF、ボタンTAP、
buttons, and meter cover, push spacer on the ウインドウ METER、プッシュスペーサーは、MAS
MAS 1/4 circuit board are not components of 1/4 シートの構成部品ではありません。MAS 1/4
the circuit board. When you replace the MAS 1/ シートを交換する際には、MAS 1/4 シートからリ
4 circuit board, you should remove the meter フレクター METER、ボタン ON Ass’y、スリーブ
reflector, push ON buttons, sleeve ON buttons, ONボタン、ボタンPFL、基板固定金具、ノブ(VR) 、
push PFL buttons, holder circuit board, volume ボタンHPF、ボタンTAP、ウインドウMETER、プッ
knobs, push HPF buttons, push TAP buttons, and シュスペーサーを取り外して、新しいMAS 1/4シー
meter cover, push spacer from the old MAS 1/4 トに取り付けてください。 (写真 30)
circuit board, and install in the new circuit board. ※ DSP シールドベース取付時は、DSP シート CN101
(Photo.30) のピンを MAS 1/4 シートの CN503 に入れてから
At the time of DSP shield base attachment, [760]のネジを締めてください。 (写真 14、27、28)
please tighten the screw of [760] after putting
the pin of the DSP sheet CN101 into CN503 of
MAS 1/4 sheet. (Photo. 14, 27, 28)
Select knob
(ノブ(SELECT))
[390A]
[390B]
Hexagonal nut
and flat washer [D]
(特殊六角ナットと
平ワッシャ[D])
Fader knob
(ノブ(FADER))
Photo.26 (写真26)
33
[380]
Hooks x24
(フック)
Photo.29 (写真29)
Meter reflector
MAS 3/4 (リフレクターMETER)
Push HPF buttons Toothe Lock Washer
(ボタンHPF) (歯付座金)
Holder, circuit board
Push TAP buttons (基板固定金具)
(ボタンTAP) MAS 4/4
MAS 1/4
Photo.30 (写真30)
34
[980]: (+バインドBタイト)
Bind Head Tapping Screw-B [1000]: Bind Head Tapping Screw-B(+バインドBタイト)
4.0X20 MFZN2BL (VS205900) 4.0X20 MFZN2BL (VS205900)
[930]
[940]
[930]
[930]
[930]
[930]: Bind Head Tapping Screw-S(+バインドSタイト)3.0X6 MFZN2BL (VS205900)
[940]: Bind Head Tapping Screw-B(+バインドBタイト)4.0X12 MFZN2BL (VR138400)
Photo.3 (写真3)
35
[700] [710]
Side cover L
(サイドカバーL)
[700]
[700]: Hex. Socket Set Screw(六角穴付きSタイト) [710]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (V9842300) 3.0X6 MFZN2BL (EP630210)
[730] [740]
Side cover R
(サイドカバーR)
[730]
[730]: Hex. Socket Set Screw(六角穴付きSタイト) [740]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (V9842300) 3.0X6 MFZN2BL (EP630210)
36
4. Supports 4. 台
4-1 When you work on the back of the top cover, set the 4-1 トップカバーの裏面の作業をする時、そのまま作業
supports to the right and left sides to prevent the すると基板がゆがんでしまうので、トップカバー裏
circuit boards from being distorted. (Photo.8) 面の作業をする時は、左右に台を当ててください。
(写真 8)
Supports
(台)
Photo.8 (写真8)
37
Bolt Nut(ナット)
(ボルト) [B]
[A]
[880]
Photo.9 (写真9)
[850] PS
[840]
[840]
Photo.11 (写真11)
38
[800] [780]
[800]: Bind Head Tapping Screw-S(+バインドSタイト) [780]: Bind Head Tapping Screw-S(+バインドSタイト)
3.0X6 MFZN2BL (EP630210) 3.0X6 MFZN2BL (EP630210)
[760]
Photo.14 (写真14)
39
[200]
Power switch
knob
(PSWノブ) Claw
(ツメ)
[220]
AC-IN connector(ACインレット)
[240]
PS holder(PSホルダー)
Push switch(プッシュSW)
Photo.17 (写真17)
40
Photo.18 (写真18)
Hexagonal nut and flat washer [A] Hexagonal nut and flat washer [B]
(特殊六角ナットと平ワッシャ[A]) (特殊六角ナットと平ワッシャ[B])
Photo.21 (写真21)
2222
[160]: Bonding Tapping Screw-B(ボンディングBタイト)3.0X8 MFZN2BL (VN413300)
Photo.22 (写真22)
42
Photo.23 (写真23)
43
Hooks
IN 3 IN 2 IN 1 (フック) IN 3 IN 2
(フック)
Hooks
IN 1
(フック)
Hooks
[590C] [590B] [590A]
Photo.24(写真24)
Photo.26 (写真26)
14. MAS 1/4 to 4/4 Circuit Boards 14. MAS 1/4 ∼ 4/4 シート
(Time required: About 15 minutes) 14-1 ボトムカバーを外します。 (1 項参照)
14-1 Remove the bottom cover. (See procedure 1.) 14-2 台を当てます。 (4 項参照)
14-2 Set the supports. (See procedure 4.) 14-3 ヒートシンクを外します。 (5-3 項参照)
14-3 Remove the heat sink. (See procedure 5-3.) 14-4 DSP シールドベースを外します。 (8 項参照)
14-4 Remove the DSP shield base. (See procedure 8.) 14-5 MAS 2/4:
(所要時間:約 7 分)
14-5 MAS 2/4: (Time required: About 7 minutes) 14-5-1 コントロールパネル面から、 [390A]のネジ 2 本を外
14-5-1 Remove the two (2) screws marked [390A] from the して、MAS 2/4 シートを外します。 (写真 27、30)
control panel surface. Then, remove the MAS 2/4 14-6 MAS 3/4: (所要時間:約 7 分)
circuit board. (Photo.27, 30) 14-6-1 コントロールパネル面から、 [390B]のネジ 2 本を外
14-6 MAS 3/4: (Time required: About 7 minutes) し、MAS 3/4 シートを外します。 (写真 27、30)
14-6-1 Remove the two (2) screws marked [390B] from the 14-7 MAS 4/4: (所要時間:約 7 分)
control panel surface. Then, remove the MAS 3/4 14-7-1 [E]の特殊六角ナットと平ワッシャ1個を外し、MAS
circuit board. (Photo.27, 30) 4/4 シートと基板固定金具を外します。
14-7 MAS 4/4: (Time required: About 7 minutes) (写真 27、30、31)
14-7-1 Remove the hexagonal nut and flat washer [E] from
the control panel surface.Then, remove the MAS 4/4
circuit board. (Photo.27, 30, 31)
44
14-8 MAS 1/4: (Time required: About 12 minutes) 14-8 MAS 1/4:(所要時間:約 12 分)
14-8-1 Remove the side pad R. (See procedure 1.) 14-8-1 サイドパッド R を外します。 (1 項参照)
14-8-2 Remove the twelve (12) fader knobs and the two (2) 14-8-2 コントロールパネル面から、ノブ(FADER) 12 個と
select knobs from the control panel surface. ノブ (SELECT)2 個を外します。(写真 27)
(Photo.27) 14-8-3 MAS 2/4 シートを外します。(14-5 項参照)
14-8-3 Remove the MAS 2/4 circuit board. 14-8-4 MAS 3/4 シートを外します。(14-6 項参照)
(See procedure 14-5.) 14-8-5 MAS 4/4 シートを外します。(14-7 項参照)
14-8-4 Remove the MAS 3/4 circuit board. 14-8-6 [380]のネジ 4 本を外します。 (写真 29)
(See procedure 14-6.) 14-8-7 MAS 1/4 シートを固定しているフック 24 箇所を
14-8-5 Remove the MAS 4/4 circuit board. まっすぐになるようにひねり、MAS 1/4 シートを
(See procedure 14-7.) 外します。(写真 30)
14-8-6 Remove the four (4) screws marked [380]. (Photo.29) ※ MAS 1/4 シート上のリフレクター METER、ボタン
14-8-7 Twist the twenty-four (24) hooks of the MAS 1/4 ON Ass’y、スリーブ ON ボタン、ボタン PFL、基
circuit board to become straight. Then, remove the 板固定金具、ノブ(VR) 、ボタン HPF、ボタンTAP、
MAS 1/4, 3/4, and 4/4 circuit boards. (Photo.30) ウインドウ METER、プッシュスペーサーは、MAS
The meter reflector, push ON buttons, sleeve ON 1/4 シートの構成部品ではありません。MAS 1/4
buttons, push PFL buttons, holder circuit board, シートを交換する際には、MAS 1/4 シートからリ
volume knobs, push HPF buttons, push TAP フレクター METER、ボタン ON Ass’y、スリーブ
buttons, and meter cover, push spacer on the ONボタン、ボタンPFL、基板固定金具、ノブ(VR) 、
MAS 1/4 circuit board are not components of ボタンHPF、ボタンTAP、ウインドウMETER、プッ
the circuit board. When you replace the MAS 1/ シュスペーサーを取り外して、新しいMAS 1/4シー
4 circuit board, you should remove the meter トに取り付けてください。 (写真 31)
reflector, push ON buttons, sleeve ON buttons, ※ DSP シールドベース取付時は、DSP シート CN101
push PFL buttons, holder circuit board, volume のピンを MAS 1/4 シートの CN503 に入れてから
knobs, push HPF buttons, push TAP buttons, and [760]のネジを締めてください。 (写真 14、28、29)
meter cover, push spacer from the old MAS 1/4
circuit board, and install in the new circuit board.
(Photo. 31)
At the time of DSP shield base attachment,
please tighten the screw of [760] after putting
the pin of the DSP sheet CN101 into CN503 of
MAS 1/4 sheet. (Photo. 14, 28, 29)
Select knob
(ノブ(SELECT))
[390A]
[390B]
Hexagonal nut
and flat washer [E]
(特殊六角ナットと
平ワッシャ[E])
Fader knob
(ノブ(FADER))
Photo.27 (写真27)
45
[380]
Hooks x24
(フック)
Photo.30 (写真30)
Meter reflector
MAS 3/4 (リフレクターMETER)
Push HPF buttons Toothe Lock Washer
(ボタンHPF) (歯付座金)
Holder, circuit board
Push TAP buttons (基板固定金具)
(ボタンTAP) MAS 4/4
MAS 1/4
Photo.31 (写真31)
46
47
48
AK4522VF-E2 (XW008A00) CODEC (CMOS A/D & D/A Converter) DSP: IC108, 308
PIN PIN
NAME I/O FUNCTION NAME I/O FUNCTION
NO. NO.
1 VREFH I Positive voltage reference input , VA 13 SDTO O Audio serial data output
Used as a positive voltage reference by 14 SMUTE I Soft mute
ADC & DAC, VREFH is conne externally When this pin goes "H", soft mute cycle
to filtered VA. is intiated.
2 AINR+ I Rch analog positive input When returning "L", the output mute releases.
3 AINR- I Rch analog negative input 15 DEM0 I
De-emphasis frequency select
4 AINL+ I Lch analog positive input 16 DEM1 I
5 AINL- I Lch analog negative input 17 MCKI I Master clock Input/X'tal input
6 VA - Analog power supply 18 VD - Digital power supply
7 AGND - Analog ground 19 DGND - Digital ground
8 DIF0 I 20 /PD I Reset
Audio data interface format
9 DIF1 I 21 CMODE I Master clock select (Internal biased pin)
10 LRCK I Input/Output channel clock "H": 384fs, "L": 256fs, "NS": 512fs
11 SCLK I Audio serial data clock 22 AOUTL O Lch analog output
12 SDTI I Audio serial data input 23 AOUTR O Rch analog output
24 VCOM O Common voltage output , VA/2
49
1A 1 14 VDD
1A 1 14 VDD
1B 2 13 4B
1Y 2 13 +DC Voltage
6A Output A 1 +V 8
1Y 3 12 4A Supply
2A 3 12 6Y Inverting
2 7 Output B
Input A - +
4 2A 4 11 4Y Inverting
2Y 11 5A Non-Inverting 3 6
Input A + - Input B
5 10 2B 5 10 3B Non-Inverting
3A 5Y Ground 4 -V 5
Input B
6 9 2Y 6 9 3A
3Y 4A
Vss 7 8 4Y VSS 7 8 3Y
RQ
- D12
+ SQ 6
GND
50
CIRCUIT BOARDS(シート基板図)
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
to MAS 1/4-CN503
Component side(部品側)
51
Pattern side(パターン側)
52
INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O
MG24/14FX: MG24/14FX: MG24/14FX: MG24/14FX: MG24/14FX: MG24/14FX: MG24/14FX: MG24/14FX:
8, 16 7, 15 6, 14 5, 13 4, 12 3, 11 2, 10 1, 9
MG32/14FX: MG32/14FX: MG32/14FX: MG32/14FX: MG32/14FX: MG32/14FX: MG32/14FX: MG32/14FX:
8, 16, 24 7, 15, 23 6, 14, 22 5, 13, 21 4, 12, 20 3, 11, 19 2, 10, 18 1, 9, 17
Component side(部品側)
Pattern side(パターン側)
53
IN Circuit Board
PAD GAIN 80 HIGH MIDI-f MID LOW AUX1 AUX2 PRE AUX3 AUX4 PRE
(HPF) (AUX1-2) (AUX3-4)
A'
54
PEAK SIGNAL
ON PFL
55
IN Circuit Board
B
to IN-CN110 or to IN-
to MAS-CN302 to MA
to IN-CN111 to IN
B'
56
CN103: to INJK-CN103
B CN104: to INJK-CN104
to IN-CN108 or to IN-CN107 or
to MAS-CN301 to MAS-CN903
to IN-CN109 to IN-CN106
B'
CN101: to INJK-CN101
CN102: to INJK-CN102
Pattern side(パターン側)
57
to PS-CN105
to PS
-CN104
to PS
-CN103
C'
58
C
MAS 4/4 Circuit Board
to IN-CN111
D'
60
D
MAS 3/4 Circuit Board MAS 2/4 Circuit Board
to MASJK
-CN701
to MASJK
-CN601
to MASJK
-CN501
to MASJK
-CN401
to DSP
-CN101
to MASJK
-CN301
to MASJK
-CN201
to MASJK
-CN101
to IN-CN109 to IN-CN106
D'
Pattern side(パターン側)
61
FOOT
SWITCH ST SUB ST INSERT GROUP GRPINS I/O SEND SEND
(EFFECT2) OUT R I/O R OUT 2 2 AUX6 AUX2
TAP
SEND SEND RETURN 2L RETURN 1L 23L, 21L, 19L (MONO), 17L (MONO),
AUX5 AUX1 (MONO) (MONO) 31L 29L 27L (MONO) 25L (MONO)
62
F'
Pattern side(パターン側)
F'
63
PS Circuit Board
to MAS 2/4-CN908
from
AC-SW
to
Transformer
to MAS 1/4
-CN904
Component side(部品側)
Pattern side(パターン側)
64
INSPECTIONS
1. Scope
This inspection specifications is applied to the mixer MG32/14FX and MG24/14FX.
2. Power Supply
Power supply cord that fit the mixer’s destination shall be used.
65
ON switch ON (LED shall light) when taking measurement only / OFF otherwise
PFL switch ON (LED shall light) when taking measurement only / OFF otherwise
1-2 switch ON when taking measurement only / OFF otherwise
3-4 switch ON when taking measurement only / OFF otherwise
ST switch ON when taking measurement only / OFF otherwise
Fader MAX
• DIGITAL EFFECT 1, 2
PROGRAM select switch 1
PARAMETER control MIN
AUX1-4 level control MAX
ON switch ON (LED shall light) when taking measurement only / OFF otherwise
PFL switch ON (LED shall light) when taking measurement only / OFF otherwise
1-2 switch ON when taking measurement only / OFF otherwise
3-4 switch ON when taking measurement only / OFF otherwise
ST switch ON when taking measurement only / OFF otherwise
EFFECT RTN fader MAX
• MASTER control
GROUP1-4 TO ST assign switch OFF
GROUP1-4 TO ST PAN control Center
GROUP1-4 master fader MAX
ST, MONO master fader MAX
LPF (MONO) switch OFF
LPF (MONO) frequency control MIN (80Hz)
AUX1-6, EFFECT1, 2 send master control MAX
RETURN1, 2 to AUX1-4, ST level control MAX when taking measurement only/ MIN otherwise
RETURN1, 2 PFL switches ON (LED shall light) when taking measurement only / OFF otherwise
2TR IN to ST level control MAX when taking measurement only/ MIN otherwise
2TR IN PFL switch ON (LED shall light) when taking measurement only / OFF otherwise
ST SUB OUT MAX
TB level control MAX
TB to AUX1-4, ST assign switches ON (LED shall light) when taking measurement only / OFF otherwise
PHONES level control MAX when taking measurement only/ MIN otherwise
METER source select switch ST, AFL/PFL
All AFL switches ON when taking measurement only / OFF otherwise
• Others
PHANTOM switches OFF
4.2 Gain
The output levels shall be within the range specified in the Table 4.2-1~11.
IN the column named PAN or BAL, a character “C” means center. About the mark (#) or ($), refer to section 4.3 or 4.10.
When PAN or BAL control is set to center, do not turn on two or three switches of [1-2], [3-4] or [ST].
In case of two or three of the switches ON, the output level is 1 or 2dB lower.
Table 4.2-1 CH INPUT A (1-16: MG24/14FX, 1-24: MG32/14FX) [dBu]
Do not insert jacks to INPUT B.
INPUT GROUP1, 3 GROUP2, 4 ST OUT AUX1-4 OUT AUX5, 6, PHONES OUT
INPUT Gain PAD PAN
level OUT OUT (L, R) PER OFF PRE ON EFFECT1, 2 OUT (L, R) *2
L +14 ±2 (#, $1) – – +16 ±2 (#, $2) +6 ±2 +16 ±2 (#, $2) -1.0 ±2 (#, $2)
-70 MAX OFF R – +14 ±2 (#, $2) – – – – –
A C – – +11 ±2 (#, $2) – – – –
-26 MIN OFF L +14 ±2 *1 (#) – – – – – –
0 MIN ON L +14 ±2 *1 – – – – – –
66
67
68
4.4 HPF
In the state of the Table 4.2-1, feeding 80 Hz -36dBu signal, and setting the GAIN to MIN, the STEREO L OUT level
obtained when the 80 switch is set to ON shall be within the range of -3 +/-2 dB compared to the level obtained when the
switch is set to OFF.
69
4.7 Crosstalk
Set the GROUP1-4, ST and MONO master fader to the MAX position. At the input CH1, set the fader to the MAX position
and turn on the ON switch.
Turn the 1-2 assign switch ON and the PAN control (BAL control in the case of ST CH INPUT) counterclockwise fully.
When the signal of +20dBu is outputted to the GROUP1 OUT output, the level of the leakage into GROUP2 OUT output
shall be -50dBu or less. Also turning the PAN control clockwise fully, when the signal of +20dBu is outputted to the
GROUP2 OUT output, the level of the leakage into GROUP1 OUT output shall be -50dBu or less. The same is said of
relation between GROUP3 and GROUP4, ST L and R.
70
4.14 Phase
In the state 4.1, the phase of the input signal and the output signal shall be the same.
4.15 PHANTOM
Connect a 10kohms load resistance between the pin 1 and 2 of the INPUT A and short-circuit between the pin 2 and 3.
Turn on the PHANTOM switch (LED shall light) and the voltage between pin 1 and 2 shall be within +35 +/-3V.
4.16 LAMP
Connect a 30ohms load resistance between the pin 2 and 3 of the LAMP(12V) connector. The voltage between pin 2 and
3 shall be within 10.7 +/-1VAC.
Table 4.17-2
EFF RTN1, 2 EFF RTN1, 2 EFF RTN1, 2 GROUP, ST EFF RTN1 EFF RTN2 EFF RTN1 EFF RTN2 GROUP
ST
1-2, 3-4 ST PARAMETER fader fader PROGRAM PROGRAM ON SW ON SW 1-4 OUT
8 – ON OFF +10.5 ±3 +10.5 ±3
ON MIN MAN MAN
– 16 OFF ON +10.5 ±3 +10.5 ±3
Table 4.17-3
EFF RTN1, 2 EFF RTN1, 2 EFF RTN1 EFF RTN2 EFF RTN1 EFF RTN2
PHONES OUT
PFL PARAMETER PROGRAM PROGRAM ON SW ON SW
8 – ON OFF -4.5 ±3
ON MIN
– 16 OFF ON -4.5 ±3
4.18 Stability
Shunt the output terminal with the capacitance of 10pF-0.1microF respectively. Then, the unit shall not oscillate.
Shunt the all input terminals with 150 ohms, and set the all VR and EQ Control to MAX. Then, the unit shall not oscillate.
71
検査
1. 適用範囲
ミキサー MG24/14FX と MG32/14FX について規定します。
2. 電源
仕向け地にあった電源コードを使用します。
4. ミキサー部の検査
4.1 準備
各出力端子の負荷抵抗は下記の通りです。
・PHONES(L,R): 40 Ω Unbalanced
・ST OUT: 600 Ω Balanced
・MONO OUT: 600 Ω Balanced
・GROUP1-4 OUT: 600 Ω Unbalanced
・AUX1-6 OUT: 600 Ω Unbalanced
・その他出力: 10k Ω Unbalanced
特に指定の無い場合、ツマミ類は以下のように設定してください。
72
・DIGITAL EFFECT 1, 2
PROGRAM select switch 1
PARAMETER control MIN
AUX1-4 level control MAX
ON switch 測定時のみ ON(LED 点灯)、他は OFF
PFL switch 測定時のみ ON(LED 点灯)、他は OFF
1-2 switch 測定時のみ ON、他は OFF
3-4 switch 測定時のみ ON、他は OFF
ST switch 測定時のみ ON、他は OFF
EFFECT RTN Fader MAX
・MASTER control
GROUP 1-4 TO ST assign switch OFF
GROUP 1-4 TO ST PAN control CENTER
GROUP1-4 Master Fader MAX
ST, MONO Master Fader MAX
LPF (MONO) switch OFF
LPF (MONO) frequency control MIN(80Hz)
AUX1-6, EFFECT1, 2 send Master control MAX
RETURN 1, 2 to AUX1-4 ST level control 測定時のみ MAX、他は MIN
RETURN 1, 2 PFL switches 測定時のみ ON(LED 点灯)、他は OFF
2TR IN to ST level control 測定時のみ MAX、他は MIN
2TR IN PFL switch 測定時のみ ON(LED 点灯)、他は OFF
ST SUB OUT MAX
TB level control MAX
TB to AUX 1-4, ST assign switches 測定時のみ ON(LED 点灯)、他は OFF
PHONES level control 測定時のみ MAX、他は MIN
METER source select switches ST, AFL/PFL
All AFL switches 測定時のみ ON、他は OFF
・Others
PHANTOM switch OFF
4.2 利得
4.1 の状態で各出力端子には[表 4.2-1 ∼ 4.2-11]の範囲内の出力レベルが得られることを確認します。
PAN または BAL の列では「C」はセンターを意味します。
(#)や($)の印については 4.3 または 4.10 を参照してください。
PAN または BAL を「C 」で測定する場合、「1-2」、「3-4」、「ST」スイッチを同時に 2 つ以上 ON にしないでください。
2 つまたは 3 つ同時に ON すると 1dB または 2dB 規定値よりも低下します。
73
表 4.2-4 ST CH INPUT (18 and 20: MG24/14FX, 26 and 28: MG32/14FX) [dBu]
※ MG24/14FX の 17 と 19Ch、MG32/14FX の 25 と 27Ch の入力は無信号であることを確認してください。
INPUT PHONES PHONES
INPUT Gain BAL PFL
level OUT L OUT R
R -44 MAX – ON No signal -1.0 ±2
※ 入力チャンネル間のレベル差は 2dB 以下であることを確認します。
表 4.2-5 ST CH INPUT (21-24: MG24/14FX, 29-32: MG32/14FX, Phone jacks) [dBu]
INPUT GROUP1, 3 GROUP2, 4 ST OUT AUX1-4 OUT AUX5, 6, PHONES PHONES
INPUT Gain BAL
level OUT OUT (L, R) PER OFF PRE ON EFFECT1, 2 OUT OUT L *2 OUT R *2
L L +14 ±2 – – +13 ±2 ($3) +3 ±2 ($3) +13 ±2 -1.0 ±2 -1.0 ±2
(Phone) -44 MAX R – +14 ±2 – – – – – –
& C – – +11 ±2 (#, $) – – – – –
R L +14 ±2 *1 (#) – – – – – – –
0 MIN
(Phone) R – +14 ±2 *1 (#) – – – – – –
*1: GROUP1 と 2 のみ測定します。
*2: PFL スイッチを ON にします。
※ 入力チャンネル間のレベル差は 2dB 以下であることを確認します。
※ GROUP1 から 4 のレベル差は 2dB 以下であることを確認します。AUX1 から 6、EFFECT1 と 2、ST の L と R も同様
です。
74
表 4.2-7 ST CH INPUT (21-24: MG24/14FX, 29-32: MG32/14FX, PCA PIN jacks) [dBu]
INPUT PHONES PHONES
INPUT Gain BAL PFL
level OUT L OUT R
21, 23/29, 31 -1.0 ±2 –
-44 MAX – ON
22, 24/30, 32 – -1.0 ±2
*1: R にジャックを挿さないでください。
*2: L (MONO)の入力は無信号であることを確認します。
*3: PFL スイッチを ON にします。
*4: 2TR IN のレベルコントロールを MAX にします。
*5: TB の AUX1-4、ST アサインスイッチを ON にします。
※ RETURN1, 2 から入力した時の AUX1 から 4 のレベル差は 2dB 以下であることを確認します。RETURN1, 2 から入力
した時の ST の L と R も同様です。
表 4.2-12 ST, GROUP1-4 INSERT INPUT [dBu]
INPUT GROUP1-4
INPUT ST OUT L ST OUT R
level OUT
ST INSERT L
+4 ±2 – –
INPUT
ST UBSERT R
-10 – +4 ±2 –
INPUT
GROUP1-4
– – +4 ±2
INSERT INPUT
75
4.3 周波数特性
表4.2-1∼4.2-11の(#)のついた系統において、印加信号周波数を20Hz・20kHzとした時、各出力端子の出力レベルは1kHz
を基準として、+1.0dB,-2.5dB の範囲内にあることを確認します。(##)の系統[TB MIC入力]は、20Hzの代わりに 163Hz
を印加し、-3 ± 2 の範囲内であることを確認します。
※ GAIN VR MAX の時は、20Hz のみ +1.0dB,-4.5dB とします。
※ 表 4.2-1 と 4.2-2 の系統は、CH1 のみ全部の OUT で確認し、CH2 以降は ST L OUT のみ確認します。
※ Phones に限って 20Hz の時は GAIN MAX 時は 0dB、-5.5dB とします。
※ Phones に限って 20Hz の時は GAIN MIN 時は 0dB、-3.5dB とします。
4.4 HPF
表4.2-1 の状態で入力レベル-36dBu、Gain を MIN として入力信号を 80Hzとし、80 スイッチを ONにしたとき、STEREO
L OUT の出力レベルは OFF 時のレベルを基準として -3 ± 2dB の範囲内であることを確認します。
表 4.6-2 CH17-24/25-32[dB]
EQ Level control Applied frequency Variation width
MAX +12 ± 2
HIGH 10kHz
MIN -12 ± 2
MAX +15 ± 2.5
HI-MID 3kHz
MIN -15 ± 2.5
MAX +15 ± 2.5
LO-MID 800Hz
MIN -15 ± 2.5
MAX +12 ± 2
LOW 100Hz
MIN -12 ± 2
76
4.10 歪み
表 4.2-1 から 4.2-11 の($)、($1)、($2)、($3)のついた系統において、INPUT 及び MASTER の各 VR とフェーダーをノミナル
ポジションとし、GAIN コントロールは表に従って設定した時に、20Hz, 1kHz, 20kHz の入力信号について各出力端子に
+14dBu の出力が得られた時の歪率は 0.1% 以下であること確認します。(PHONES を除く)
PHONES OUT (L/R)は PHONES レベルコントロールつまみの 12 時の方向とし、20Hz, 1kHz, 20kHz の入力信号につい
て +3dBu の出力が得られた時の歪率は 0.2% 以下であること確認します。
※ ($1): CH1 のみ GROUP1 と GROUP3 を確認し、CH2 以降は GROUP1 のみ確認します。
※ ($2): CH1 のみ確認します。
※ ($3): AUX1 のみ確認します。
4.11最大出力
4.1 の状態で、ST L/R OUT と MONO OUT に +24dBu、GROUP1-4 OUT、AUX1-6 OUT、EFFECT1-2 OUT、ST SUB L/
R OUT に +20dBu の信号が出力される時、1kHz での 歪率は 1% 以下であることを確認します。
PHONES (L/R)に +7.5dBu の信号が出力される時、1kHz での歪率は 1% 以下であることを確認します。
ST L/R OUT, GROUP1-4 OUT, ST SUB L/R 測定時は、PAN または BAL コントロールをそれぞれ L または R に回しきっ
てください。
4.12 入力換算雑音
4.1 の状態で、CH INPUT MIC 入力端子を 150 Ωで短絡し、ST アサインと CH ON スイッチを ON した時、ST L OUT
で得られるノイズレベルは -44dBu 以下であることを確認します。
ノイズレベルが -44dBu 以上の場合は、入力換算でのノイズレベルを求めそれが -128dBu 以下であれば良いです。
4.13 残留雑音
4.1の状態で全ての入力部のフェーダーとレベルコントロールをMINにし、すべてのアサインスイッチとCH ONスイッ
チを OFF にします。
この時、マスター部のフェーダーやレベルコントロールを最大または最小にした時のノイズレベルは[表 4.13-1]のレ
ベル以下であることを確認します。
表 4.13-1 [dBu]
Fader/VR ST L/R OUT MONO OUT GROUP1-4 OUT AUX1-6 OUT EFFECT1-2 OUT PHONES OUT ST SUB OUT
MAX -74 -73 -77 -72 -76 -80 -78
MIN -99 -99 -100 -100 -100 -100 -100
4.14 位相
4.1 の状態で各入力端子に印加された信号と各出力端子で得られる信号は同相であることを確認します。
77
4.15 PHANTOM
MIC 入力コネクタのピン 1-2 間に負荷抵抗 10k Ω(1W 以上)を接続し、ピン 2-3 間を短絡します。
PHANTOM スイッチを ON にした時、LED が点灯し負荷抵抗両端に +35 ± 3V の電圧が得られることを確認します。
4.16 LAMP
LAMP (12V)コネクタのピン 2-3 間に負荷抵抗 30 Ω(5W 以上)を接続します。
負荷抵抗両端に 10.7 ± 1VAC の電圧が得られることを確認します。
表 4.17-2
EFF RTN1, 2 EFF RTN1, 2 EFF RTN1, 2 GROUP, ST EFF RTN1 EFF RTN2 EFF RTN1 EFF RTN2 GROUP
ST
1-2, 3-4 ST PARAMETER fader fader PROGRAM PROGRAM ON SW ON SW 1-4 OUT
8 – ON OFF +10.5 ±3 +10.5 ±3
ON MIN MAN MAN
– 16 OFF ON +10.5 ±3 +10.5 ±3
表 4.17-3
EFF RTN1, 2 EFF RTN1, 2 EFF RTN1 EFF RTN2 EFF RTN1 EFF RTN2
PHONES OUT
PFL PARAMETER PROGRAM PROGRAM ON SW ON SW
8 – ON OFF -4.5 ±3
ON MIN
– 16 OFF ON -4.5 ±3
4.18 安定度
各出力端子において負荷抵抗と並列に10pF∼0.1uFのコンデンサを接続した場合にも発振等の異常がないことを確認し
ます。
また、全ての Fader,Level control,EQ を最大にしても発振等の異常がないことを確認します。但し、入力端子は 150
Ωでショートしてください。
4.19 電源電圧変動
電源電圧を規定の± 10% 変化させても動作に異常のないことを確認します。
78
PARTS LIST
CONTENTS(目次)
OVERALL ASSEMBLY MG24/14FX(総組立).......................... 2
OVERALL ASSEMBLY MG32/14FX(総組立).......................... 6
ELECTRICAL PARTS(電気部品)...................................... 10-56
WARNING
Components having special characteristics are marked and must be replaced with parts having
specification equal to those originally installed.
印の部品は、安全を維持するために重要な部品です。交換する場合は、安全のために必ず指定の部品をご
使用ください。
MG24/14FX MG32/14FX
390
350 930
210
560 60 240
230
390
280
20 250
340 550
560
480 MAS 2/4 20 540 PAGE 3
c
390 530 190
360 260 270
370 340 20 520
365 MAS 3/4
352 310 GND
370 490
400
480 30
340 480 340
MAS 1/4 MAS 4/4
590
560
600
590
340 560
610 420
a b
560 380
d 340
610 PAGE 3
430
560
430
PAGE 2
810
a PAGE 2
L=60 b
d
60 c
750 60
900 820
700
850
840
e
840
850 760
905
820
760 900
e 905
780
770
982
980 780
790 890
800
922 990
930 720
930
1002
940
950 1000
950
• REAR View 960
940 960
880
940
930 865
1010
950
MG32/14FX
MG24/14FX
960
3
ACCESSORIES 付 属 品
V7240300 AC Cord J VCTF 0.75X3 電 源 コ ー ド J 05
* WA775400 AC Cord LP-31L 電 源 コ ー ド U,V
* WA775500 AC Cord LP-34A 電 源 コ ー ド H,W,K
* WA775600 AC Cord LP-60L 電 源 コ ー ド B
390
930
350 20 210
560 60 240
230
390 20
280
340 250
550
560 480 20
MAS 2/4 540 PAGE 7
480
c
390 530 190
360 260 270
30 520
340
365 490 370
MAS 3/4 310 GND
370 400
480 352
590
560
610 600
590
560 560
340
610 610 420
a b
560 380
d 340
610 PAGE 7
430
560
430
PAGE 6
810
a PAGE 6
L=60 b
d
60 c
750 60
900 820
700
850
840
e
840
850 760 905
820
760 900 905
e
780
770
982
980 780
790 890
800
865 740
897
870
730
930
930
990
922
720
950 1002
960
940
1000
950
• REAR View
940 960
880
940
930 865
1010 950
MG32/14FX
MG24/14FX
960
7
ACCESSORIES 付 属 品
V7240300 AC Cord J VCTF 0.75X3 電 源 コ ー ド J 05
* WA775400 AC Cord LP-31L 電 源 コ ー ド U,V
* WA775500 AC Cord LP-34A 電 源 コ ー ド H,W,K
* WA775600 AC Cord LP-60L 電 源 コ ー ド B
ELECTRICAL PARTS(電気部品)
REF NO. PART NO. DESCRIPTION 部 品 名 REMARKS QTY RANK
ELECTRICAL PARTS 電 気 部 品 MG24/14FX,MG32/14FX
* WA266500 Circuit Board DSP1000 シートDSP1000 (X3710B0)
* WA266100 Circuit Board IN1000 シートIN1000 (X3706B0)
* WA266300 Circuit Board INJK1000 シートINJK1000 (X3708B0)
* WA266000 Circuit Board MAS1000 (1/4-4/4) シートMAS1000 (X3705B0)
* WA266200 Circuit Board MASJK1000 シートMASJK1000 (X3707A0)
* WA266400 Circuit Board PS1000 シートPS1000 (X3709B0)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
CIRCUIT DIAGRAM
CONTENTS(目次)
BLOCK DIAGRAM & LEVEL DIAGRAM
(ブロックダイアグラム&レベルダイアグラム).................... 3
OVERALL CIRCUIT DIAGRAM(総回路図)
DSP .................................................................................. 4
IN .................................................................................. 5-9
INJK ............................................................................... 10
MAS 1/4 .................................................................... 11-18
MAS 2/4 ......................................................................... 18
MAS 3/4 ......................................................................... 14
MAS 4/4 ......................................................................... 18
MASJK .................................................................... 19, 20
PS ................................................................................... 21
ONLED to page 8: N7
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
IC107b,
207b (8P) IC808
IC806 (8P) MONO Fader (8P)
CN101 (13P) CN101 (13P) JK603
IC807a (8P)
MONO OUT
MAS 1/4 IC807b (8P)
[+4dBu]
IC909 (24P)
1
MASJK
JK105, 107, 109
ST CH INPUT Same As 1 IC301, 401 (8P) IC302, 303, 304, 305, IC306, 307, 406, 407 (8P) IC910
[-34dBu to +10dBu] L 402, 403, 404 (8P) (24P)
MG24/14FX: CH21(L)/22(R), CH23(L)/24(R)
MG32/14FX: CH29(L)/30(R), CH31(L)/32(R)
IC501a, 502a (8P) IC903a (8P) IC903b (8P) IC911
JK201, 203
R (24P)
L (MONO)
IC905a (8P)
IC908a (8P) 4/4
IC906b (8P) CN906 (3P) CN907 (3P)
IC901a (8P)
L
2TR IN JK205
[-10dBu] R
IC901b (8P)
JK901
IC503 (8P)
Same As 2
JK301~306
This is a diagram about ST OUT and MONO OUT when a signal inputs from
one of the ST INSERT L INPUT and the ST INSERT R INPUT.
4
CN503 (34P) ST INSERT I/O IC802a IC803
2
CN601 (13P) CN301 (13P) [0dBu] (8P) (8P) ST OUT
DSP IC504a (8P) L [+4dBu]
JK505 L JK601
ST Fader
R
MASJK
IC504b (8P) JK506 R JK602
IC604b (8P) IC608b (8P) CN601 (13P)
MASJK
IC802b IC804 MONO
EFFECT OUT 1 (8P) (8P) OUT
[+4dBu] CN501 (13P)
IC805, 806 JK603
TAP JK307 IC807 IC808
(8P)
JK701 (8P) (8P)
CN701 CN702
CN502 (3P) EFFECT OUT 2 CN801 (13P)
(3P) (13P) MAS 1/4
FOOT IC604a (8P) IC608a (8P)
[+4dBu]
SWITCH JK308
MASJK
38CA1-8828050 1
3
6
MCU EEPROM 2K
5
N.C
6 DIR2
N.C
8
AND
INVERTER
9
DRAM 4M
OP AMP
10 CODEC
11
µPC29M33T-E1(XU965A00) DSP6
REGULATOR +3.3V OP AMP
12 OP AMP
2
1 OP AMP
13 3 CODEC
1: INPUT
2: COMMON
3: OUTPUT
14
OP AMP
15 DRAM 4M
OP AMP
OP AMP
OP AMP 3
OP AMP
OP AMP
OP AMP
6
OP AMP
to Page 7: F12
OP AMP
OP AMP
OP AMP
7
to MAS 1/4-CN903 to IN-CN106
(to Page 18)
to IN-CN107
8
OP AMP
OP AMP
OP AMP
9
to INJK-CN102 to Page 8: O11
OP AMP
(to Page 10)
OP AMP
OP AMP
10
11
OP AMP
OP AMP
OP AMP
to Page 8: J11
12
: Ceramic Capacitor (セラミックコンデンサー)
28CC1-8828045-1 2
: Mylar Capacitor (マイラーコンデンサー)
5
( D ) : Metal Film Resistor (chip) (チップ金属被膜抵抗)
2
OP AMP OP AMP
3 OP AMP
OP AMP
4 OP AMP
5
OP AMP
OP AMP
OP AMP
6 OP AMP
to Page 9: O11
OP AMP
OP AMP
OP AMP OP AMP
8
OP AMP
OP AMP
9
to INJK-CN104 to Page 9: J11
OP AMP
(to Page 10)
OP AMP
10
OP AMP
11
OP AMP
OP AMP
OP AMP
to Page 9: E11
12
: Ceramic Capacitor (セラミックコンデンサー)
28CC1-8828045-2 2 : Mylar Capacitor (マイラーコンデンサー)
6 ( D ) : Metal Film Resistor (chip) (チップ金属被膜抵抗)
13
to Page 8: P1, 9: P1
2
to Page 8: P2, 9: P2
to IN-CN109 to IN-CN111
to Page 8: N7
OP AMP OP AMP
8
9
to Page 8: N8
10
12
28CC1-8828045-3 2 to Page 5: N4 to Page 5: N7
from Page 7
to Page 9: P2
2
from Page 7
7 to Page 9: N7
from Page 7: D8
to Page 9: N8
10
OP AMP OP AMP OP AMP
11
28CC1-8828045-4 2
12 8
2
from Page 7: B3, 8: A2
7
from Page 8: B7
from Page 8: B9
OP AMP OP AMP OP AMP
10
OP AMP OP AMP OP AMP
11
28CC1-8828045-5 2
9 12
3
INPUT B INPUT B INPUT B INPUT B
MG24/14FX: CH1, 9 MG24/14FX: CH3, 11 MG24/14FX: CH5, 13 MG24/14FX: CH7, 15
MG32/14FX: CH1, 9, 17 MG32/14FX: CH3, 11, 19 MG32/14FX: CH5, 13, 21 MG32/14FX: CH7, 15, 23
INSERT I/O 0dBu INSERT I/O 0dBu INSERT I/O 0dBu INSERT I/O 0dBu
MG24/14FX: CH2, 10 MG24/14FX: CH4, 12 MG24/14FX: CH6, 14 MG24/14FX: CH8, 16
MG32/14FX: CH2, 10, 18 MG32/14FX: CH4, 12, 20 MG32/14FX: CH6, 14, 22 MG32/14FX: CH8, 16, 24
28CC1-8828047 1
10
MAS 1/4
to Page 12: L12 to Page 12: K12 to Page 12: F12 to Page 12: E12 to Page 13: M12 to Page 13: L12 to Page 13: G12 to Page 13: F12
3
OP AMP OP AMP OP AMP OP AMP
4
OP AMP OP AMP OP AMP OP AMP
5
OP AMP OP AMP OP AMP OP AMP
7
OP AMP OP AMP OP AMP OP AMP
10
OP AMP
11
5
OP AMP OP AMP
OP AMP OP AMP
: Ceramic Capacitor (セラミックコンデンサー)
7
OP AMP OP AMP
OP AMP OP AMP
10
28CC1-8828044-2 2
12 12 from Page 11: P3 from Page 11: N3 from Page 11: L3 from Page 11: K3
3
MAS 1/4
5
OP AMP OP AMP
OP AMP OP AMP
7
OP AMP OP AMP
OP AMP OP AMP
10
MAS 1/4
2
from Page 12: A1, 13: A1, 15: A1 to Page 13: O1, 18: P11
from Page 12: A1, 13: A1, 15: A1 to Page 13: O1, 18: P10
from Page 12: A1, 13: A1, 15: A1 to Page 13: O1, 18: P9
from Page 12: A2, 13: A2, 15: B1 to Page 13: O2, 16: J11
from Page 12: A2, 13: A2, 15: B1 to Page 13: O2, 16: K11
from Page 12: A2, 13: A2, 15: B1 to Page 13: O2, 16: M11
from Page 12: A2, 13: A2, 15: B1 to Page 13: O2, 16: O11
3 from Page 12: A3, 13: A2, 15: B1 to Page 13: O3, 17: P11
from Page 12: A3, 13: A3, 15: B1 to Page 13: O3, 17: P11
OP AMP
OP AMP
7 OP AMP OP AMP OP AMP
OP AMP
OP AMP OP AMP
MIC
-50dBu
28CC1-8828044-4 2
14
12
OP AMP
6
OP AMP
8
OP AMP
10
: Ceramic Capacitor (セラミックコンデンサー)
11
28CC1-8828044-5 2
15
12
MAS 1/4
2
OP AMP
OP AMP
10
to Page 17: P11, 18: P7
11
from Page 12: A2, 13: A2, from Page 12: A2, 13: A2, from Page 12: A2, 13: A2, from Page 12: A2, 13: A2, from Page 12: A2, 13: A2 from Page 12: A2, 13: A2
14: B3, 15: B1 14: B3, 15: B1 14: B3, 15: B1 14: B3, 15: B1
from Page 12: A1, 13: A1 from Page 12: A1, 13: A1
to MASJK-CN501
(to Page 20)
2
OP AMP
3
OP AMP
to Page 18: N4
to Page 18: N4
4
OP AMP OP AMP OP AMP OP AMP
OP AMP
to Page 18: N4
to Page 18: N5
to Page 18: N5
OP AMP
OP AMP
OP AMP
6
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP
OP AMP 10
OP AMP
OP AMP OP AMP OP AMP OP AMP OP AMP
11
from Page 16: B10
from Page 16: B10
from Page 12: A3, 13: A2, 14: B3, 15: B1
from Page 12: A3, 13: A3, 14: B3, 15: B1
12
from Page 12: A2, 13: A2, 15: B1 from Page 12: A2, 13: A2, 15: B1 from Page 12: A2, 13: A2, 15: B1 from Page 12: A2, 13: A2, 15: B1
: Ceramic Capacitor (セラミックコンデンサー)
28CC1-8828044-7 2
: Mylar Capacitor (マイラーコンデンサー)
17
( D ) : Metal Film Resistor (chip) (チップ金属被膜抵抗)
13
3
MAS 1/4
LED DRIVER
LED DRIVER
5 from Page 17: K6
from Page 17: I6
7
from Page 16: B10
OP AMP OP AMP
LED DRIVER
LED DRIVER
8 from Page 16: B10
OP AMP OP AMP
OP AMP
MAS 4/4
OP AMP
from Page 12: A1, 13: A1, 14: B3, 15: A1
9
PHONES
OP AMP
OP AMP OP AMP
10 OP AMP LAMP (12V)
to PS-CN105
(to Page 21)
from Page 12: A1, 13: A1, 14: B2, 15: A1
11 MAS 2/4
OP AMP
ST CH INPUT
RETURN1
MG24/14FX: CH17 (L), 18 (R)
+4dBu
MG32/14FX: CH25 (L), 26 (R)
AUX2
R R
2
AUX3
AUX6
4
L
ST CH INPUT
MG24/14FX: CH21 (L), 22 (R) 2TR IN
MG32/14FX: CH29 (L), 30 (R) -10dBV
L R
EFF1
R
5
L R
EFF2
REC OUT
from Page 20: G6
-10dBV
from Page 20: G7
L
ST CH INPUT
MG24/14FX: CH23 (L), 24 (R)
MG32/14FX: CH31 (L), 32 (R)
7
R
28CC1-8828046-1 1
19 8
R
2
2
GRPINS I/O
to MAS 1/4-CN701 0dBu
(to Page 17)
3 to MAS 1/4-CN801
(to Page 17)
3
4
L
ST SUB OUT
+4dBu
4 1
2
MONO
GROUP OUT +4dBu
+4dBu
5
3
to MAS 1/4-CN702
(to Page 17)
4
6
to Page 19: E6
ST INSERT I/O
0dBu
to Page 19: E6
7 R
to MAS 1/4-CN502
FOOT SWITCH TAP
not installed
* Note: CN801 is not necessary to mount.
8
28CC1-8828046-2 1
20
to IN
REGULATOR +15V
2
to MAS
to DSP
REGULATOR -15V
32 32
1 1 REGULATOR +5V
1: OUTPUT 1: OUTPUT
2: COMMON 2: INPUT 4
3: INPUT 3: COMMON
NJM7812FA(XJ608A00) NJM7805FA(XJ607A00)
REGULATOR +12V REGULATOR +5V
*
32 32 5
1 1
to DSP
to LED
6
PBU403 (VV518200)
DIODE STACK 4.0A 200V
to MAS 2/4-CN908
(to Page 18)
DIODE STACK 7
REGULATOR +12V
S2VB20(IH001120)
DIODE STACK
F100
F200 (KB000790)
F201 T4AL 250V
FUSE 8
(KB001660)
F300 T1.6AL 250V
(KB002610)
F400
T800mAL 250V
(KB000690) TO SERVICE PERSONNEL
F500 T2.5AL 250V * Note: CN106 is not necessary to mount. Critical Components Information
Components having special characteristics are marked and must be replaced with parts having
specifications equal to those originally installed.
: Ceramic Capacitor (セラミックコンデンサー)
: Mylar Capacitor (マイラーコンデンサー)
9
28CC1-8828048 2
酸 金 : Metal Oxide Film Resistor (酸化金属被膜抵抗)
21









![MG24/14FX
MG32/14FX
10
1
2
3
4
5
1
2
3
4
5
[ST SUB OUT] Control
[AFL] (After-Fader Listen) Switch
[ST Master] Fader
[MONO] Fa](https://screenshots.scribd.com/Scribd/252_100_85/326/613164303/10.jpeg)