Technical Information
11.A.003| Solvent-based Liquid Systems | Auxiliaries
Gecko® PET/PA Additive
Solvent based additives for flexible packaging
70GH325253
Description
An Ethyl acetate-based adhesion promoter for inks and varnishes, specific for polyester and nylon
substrates.
Printing process
Gravure and flexographic printing.
Applications
Surface and reverse printing.
In combination with Gecko inks and varnishes for food and beverage flexible packaging.
Dosing This additive should be added in quantity of 2 – 3% in inks of GBS, BBS GBS,
NP GBS series in order to improve the adhesion on polyester and nylon, and
to improve the bonding values in lamination.
It is also possible the application at 2 – 3% in the inks of GBT and GBT BBS
series to improve the adhesion on PVDC-coated PET.
Lamination It is recommended to laminate the material printed with inks containing this
precaution additive at least 24 hours after printing and storage (around 20°C).
Properties
Dry content 50 % ± 2 Colour Transparent
Solvents Ethyl acetate
Notes
Mixing It is possible a premix of this additive in a dilution solvent before adding it to the
final product. Stir well the additive before the use and the final product after the
addition, in order to ensure an optimal dispersion.
Leftovers The leftover inks with the addition of PET/PA additive could be used twice more
(maximum), preferably after adding also fresh ink.
Gecko PET/PA Additive 02/2021 en
Instructions for the use of printing inks for the production of primary food
packaging
For information on the use of printing inks, varnishes and additives for the manufacture of food packaging
please refer to the respective „Statement of Composition". This information is provided to allow the
calculation of possible levels of migration of evaluated substances in a worst case situation.
The manufacturer of the finished article and the filler have the legal responsibility to prove by appropriate
migration testing that it is fit for its intended purpose.
In order to maintain low residual solvents concentration in the printed film, the printer must ensure
sufficient drying of the inks, especially when retarders have been added. Residual solvent content must
be regularly monitored.
The inks must not be used in the manufacture of packaging where the printed ink layer is intended to
come into contact with foodstuff (direct food contact).
Health & Safety
The material safety data sheets contain all relevant information for the generation of appropriate internal
plant instructions. The user is responsible for all local legislation requirements.
Ink Handling
Please refer to General Guidelines for handling inks for flexible packaging.
Storage Conditions
Store the material in the original packaging at a temperature not below 5°C and not in direct contact with
sunlight.
Storage Precautions: it is recommended to pay great attention in keeping the product well sealed and
protected from air and moisture, in order to avoid its deterioration (the product hardens and becomes
unusable, if the container remains open). If a bin should not be completely used, it is recommended to
transfer the remaining material into a clean and dry new container of smaller dimension, and to protect
it against air and moisture.
Contact addresses for advice and further information can be found under www.hubergroup.com
Due to the many variables in materials for printing, design construction, processing conditions and test criteria, this Technical Data
Sheet can only be of an advisory nature. Our data reflect the latest state of our knowledge and are based on the characterist ics
established in the laboratory and on practical experience. Because there are many factors under the control of the user which may
affect processing or application/use, it is necessary for the user to carry out appropriate tests to determine whether the pr oduct(s) is
technically and safely suitable for the particular purpose, prior to use. hubergroup disclaims any liability for applications for which this
ink series is not foreseen. No warranties of any kind, either expressed or implied, are made regarding the products here desc ribed.
The English version is the master document, on which to refer for any translations.
Gecko PET/PA Additive 02/2021 Page 2/2
