Item No.

1378384

t FPV Quadrocopter Cyclone 245 RtF WiFi

Version 12/15
 CYCLONE 245 FPV

INSTRUCTION MANUAL
 Accessories list (sold separately)

Part name: Upper Part name: Lower Part name: Circuit Part name: Landing
housing housing board skid

Part name: Carbon Part name: Lithium Part name: Rotor Part name: Bearing
fibre spindle Battery blade

Part name: CW Part name: CCW

motor (black and Part name: Green light Part name: Red light
motor (red and
blue wire) white wire)

Part name: Tail light Part name: Main gear

panel

1
 Standard Accessories

3.7 V 730 mAh

Charger x1 Li-Po battery x 1 Blade x4

Delivery content

NO PART NAME QUANTITY

1 V686 Instruction Manual 1

2 V686 Aircraft 1

3 Charger 1

4 Li-Po battery 1

5 Blade 4
6 Remote control 1

Optional Parts (sold separately)

WATER GUN MONITOR FPV

CAMERA WIFI FPV

BUBBLE GUN WIFI FPV

5.8G FPV

2
 Warning
■ Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the
product, personal property and cause serious injury. This is a sophisticated hobby product.
It must be operated with caution and common sense and requires some basic mechanical
ability. Failure to operate this Product in a safe and responsible manner could result in injury
or damage to the product or other property. This product is not intended for use by children
without direct adult supervision. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the
manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or
serious injury.

Additional Safety Precautions and Warnings

1. Age recommendation: Not for children under 14 years. This is not a toy.
2. Always operate your model in open spaces away from full-size vehicles, traffic and
people.
3. Always carefully follow the directions and warnings for this and any optional support
equipment ( chargers, rechargeable battery packs, etc.) .
4. Always keep all chemicals, small parts and anything electrical out of the reach of
children.
5. Always avoid water exposure to all equipment not specifically designed and protected
for this purpose. Moisture causes damage to electronics.
6. Never place any portion of the model in your mouth as it could cause serious injury or
even death.
7. Never operate your model with low transmitter batteries.
8. Please note that you incur a penalty if you observe strangers with the camera installed
in the product without their knowledge and consent. Observe the provisions and
regulations of the country in which you use this product.

3
 Introduction
■ Thank you for choosing this REELY product. This four-axis aircraft can fly
outdoors, in order to make it easier and easier to control the aircraft, please
carefully read this manual before operating this aircraft, and please keep this
manual for any future adjustments and maintenance of reference you may
wish to make.

■ Before your first flight, please take the time to carefully read this
manual, which contains important flight information, which will help your
first flight to be a great success.

Table of Contents
Accessories list ..................................................................................1
Standard Accessories ......................................................................... 2
Delivery Content ................................................................................ 2
Optional parts .................................................................................. 2
Warning .......................................................................................... 3
Additional Safety Precautions and Warnings ................................................. 3
Introduction ...................................................................................... 4
Table of Contents ............................................................................... 4
Warning and the guide of using battery ....................................................... 4
Battery Charging ................................................................................ 5
First Flight Preparation CAUTION .............................................................6
Binding instruction .............................................................................. 7
Transmitter Controls ............................................................................ 7
First Flight instruction .......................................................................... 8
9
3D Rolling .......................................................................................
9
One key return to home ........................................................................
10
CF MODE .......................................................................................
10
CF mode Calibration ..........................................................................
10
Trouble shooting Guide ....................................................................... 10
Schematic circuit board ....................................................................... 11
Exploded View ................................................................................. 12
Parts list ........................................................................................ 13
Quadrocopter specifications .................................................................. 13

4
 Warning and the guide of using battery
CAUTION WARNING WARNING WARNING WARNING WARNING

Always use a charger Always charge Never leave charging Never charge Never Alter Batteries. Never touch or use
compatible with Batteries away from Batteries unattended. damaged Batteries. hot Batteries.
batteries. flammable materials.

The Battery Charger included It has been designed with

charges the Li-Po battery. safety in mind.

CAUTION: All Instructions and warnings must be followed exactly. Mishandling of Li-Po
batteries can result in a fire, personal injury, and/or property damage.
1. By handling, charging or using the included Li-Po battery you assume all risks associated
with lithium batteries.
2. If at any time the battery begins to balloon or swell, discontinue use and disconnect
immediately. Continuing to use, charge or discharge a battery that is ballooning or swelling
can result in fire.
3. Always store the battery at room temperature in a dry area for best results.
4. Always transport or temporarily store the battery in a temperature range between 5°C
to 48°C. Do not store the battery in the model or prolonged exposure to direct sunlight. If
stored in a high temperature environment, battery can be damaged or even catch fire.
5. Never use a Ni-CD or Ni-MH charger. Failure to charge the battery with a compatible
charger may cause fire resulting in personal injury and/or property damage.
6. Never exceed the recommended charge rate.
7. Never cover warning labels with hook and loop strips.

WARNING: Only use the charger supplied by our company. Do not use a 12V power
supply or property damage and Injury could occur.

Notice: When a LiPo battery is discharged below 3.3V, the battery may be damaged
and may no longer accept a charge. Please land the quadrocopter
immediately and recharge the battery.

5
 Battery Charging
1-cell 3.7V Variable Rate DC Li-Po Charger

Instruction:
Please only recharge LiPo flight battery with the supplied AC
charger. Connect the battery to charger wire as per below
illustration only.

Charging line

LED

3.7V 730mah

Notice: Only use the charger provided

Notice: Never attempt to power the charger from an AC outlet without the use
of a proper AC to DC adapter/ power supply.

First Flight preparation CAUTION

1. Before taking the quadrocopter into operation, ensure that the flight
battery is charged completely and the batteries in the transmitter still have
enough voltage.
2. Before powering on remote controller, please keep the joystick for the
pitch function in the bottom position.
3. Please ensure quadrocopter is successful binded before operation. First
connect the flight battery to the quadrocopter electronics plug connection
with protection against polarity reversal. The LED on the quadrocopter
flashes quickly, then switch on the remote control transmitter with the
function switch. This starts the binding process, after which transmitter
and receiver use the same digital code. If binding is completed, the LED
remains lit.
4. Do not take any risks when operating the product! Your own safety and
that of your environment is solely down to you being responsible when
dealing with the model. Improper operation may cause serious injury and
property damage! Therefore make sure to keep a sufficiently safe distance
to persons, animals or objects during operation.

6
 BINDING OF RADIO TRANSMITTER AND RECEIVER

Step1

Place the quadrocopter on a level surface.

Li-Po

3.7V 730mAh

Step2

Move the joystick for the pitch function to

the lowest setting and switch the transmit-
ter on with the on/off switch. Then push the
CAUTION joystick all the way forward and then slowly
backward again to switch the transmitter
Push the throttle stick into operating mode. The transmitter emits
to the lowest position
a single signal sound to confirm binding is
complete, and the LED remains lit.

Step3
Remove the flight vehicle battery safely
at the conclusion of the flight. This
should become a post-flight habit to
Li-Po
guard against unforeseeable problems.
3.7V 730mAh
Warning: If left connected in the flight
vehicle for a long time, the battery may be
damaged due to over-discharge, or even
become a fire hazard.

Step4
Turn off the transmitter. If transmitter
is not to be used for a long duration,
please remove the battery for storage.

Warning: If the AA batteries are left

If transmitter is not to be
used for a long time, please
in the transmitter, potential leakage
remove the battery for could occur which may damage the
storage. transmitter, and create fire hazards.

7
 Transmitter Control

1. Transmitter Control

Power Switch

Power LED

Antenna

Roll
Video

Elevator Control stick

Throttle Control stick

Throttle trim Elevator trim

Rudder trim Aileron trim

X-axis calibration key / Steering
sensitivity indicator: 40% Steering sensitivity indicator: 100%
Y-axis calibration key / Steering
sensitivity indicator: 60%
One key to return home / Light control
Steering sensitivity
indicator: 80%
Camera (CF mode press &
hold for 2 seconds)

LCD Display

2. LCD Display

Stick modes indicator Transimitter battery indicator

Stick modes indicator

Elevator trim indicator

Throttle trim indicator

Rudder trim indicator

Aileron trim indicator

8
 First Flight instruction
If you are not familiar with the controls of your V636, take a few minutes
to familiarize yourself with them before attempting your first flight.
Throttle

Throttle up Climb Throttle down Descend

Rudder

Rudder Rudder
Nose Yaws Left Nose Yaws Right
Left right
Elevator

Elevator
Elevator up Forward down Backward

Aileron

Left Right
Ailerron left Ailerron right

3D Rolling

Stable flexible, flight routes,

Drift, 3D to roll easily

Once you have mastered all basic controls, then should you proceed and attempt more
difficult maneuvers such as 3D roll. To activate 3D roll function, press top right switch
button, the transmitter will emit a single continuous sound to confirm quadrocopter is in 3D
roll mode. Move the joystick for nick and roll function quickly in the direction in which the
quadrocopter should roll and immediately bring the joystick back to the center position.
Attention: If you do not move the deflected joystick back to center position quickly enough,
the quadrcopter may execute 2 rolls in succession and thereby lose considerable altitude.
If quadrocopter is in CF mode, 3D roll cannot be activated.
9
 One Key return to home
Press and hold light control switch button for 2 seconds. Transmitter will emit a single continuous
sound to confirm, rear light will blink quickly at the same time. Quadrocopter begins to return home.
Note: Please note one key return to home will not work if 1.) during start up, stand behind
quadrocopter and that the quadrocopter is not aligned with the green propellers facing forward. 2.)
If you have changed to CF mode during flight.

CF MODE
Press and hold CF mode switch button for 2 seconds. Transmitter will emit a continuous sound to
confirm.
For you to be able to use CF mode correctly, it is necessary for you to always stand behind the
quadrocopter and look in the direction in which you aligned the quadrocopter before the start. The
quadrocopter must be aligned with the two green propellers facing forward.

CF mode Calibration
The quadrocopter has a compass that allows it to detect its direction and that it needs for flight
in CF mode. The compass comes pre-calibrated from the factory, but for each use in a new flight
area, it needs to be recalibrated.
To do this, proceed as follows:
1. As described above, first start up the transmitter and then the model. The joystick for the
throttle function must be in the lowest position so that the motors do not start running.
2. Place the quadrocopter on a level surface.
3. Press and hold the 40% switch button until the LEDs on quadrocopter begin to flash and thus
indicate the calibration mode.
4. Now turn the quadrocopter, as seen from above, clockwise until the LEDs remain lit.
5. Press and hold the 60% switch button LEDs begin to flash again.
6. Now hold the quadrocopter with the front side (green propeller) vertically on top and turn it
clockwise again until the LEDs remain lit again.
7. The calibration is thereby successfully completed.

Troubleshooting Guide
Problem Problem cause Solution
1 Receiver status LED blinks Unable to bind to transmitter. Repeat the power up initializing
continuously for more than process. (Refer to P.6:Binding of
4 seconds after flight battery radio transmitter and receiver.
Inserted. No response to control
Input.

2 No response after battery is 1. Power to the transmitter and 1. Turn on transmitter and ensure
connected to quadrocopter. receiver. flight battery Is Inserted properly.
2. Check the transmitter and 2. Use fully charged batteries.
receiver voltage. 3. Re-seat the battery and ensure
3. Poor contact on battery good contact between battery
terminals. contacts.

3 Motor does not respond to throttle Flight battery depleted. Fully charge the battery, or
stick, LED receiver flashes. replace with a fully charged
battery.

4 Main rotor continue to spin after Throttle trim accidentally Confirm throttle trim is in centre
landing. Increased during flight. or slightly below.

10
 5 Main rotor spins but unable 1. Rotor blades damaged 1. Replace main blades
to takeoff. 2. Charge or replace with a fully
2. Flight battery depleted
charged battery.

6 Strong vibration of 1.Rotor deformation 1. Replace the rotor

quadrocopter.

7 Quadrocopter drifts sideways 1. Damaged tall rotors Replace the rotor

despite trim adjustment or 2. Damaged tail drive motor
Inconsistent speed during Replace the main motor
left/right pirouette.

8 Quadrocopter still drifts quadrocopter not initialized on a Disconnect the flight battery, center
forward despite trim level surface or correctly aligned all control trims and start up the
adjustment. quadrocopter again

9 Quadrocopter cannot take off 1. Motor fall out 1. Install the motor again
after a crash.
2. Gear loosen 2. Tighten the gear

10 Large deviations headless 1. quadrocopter not initialized on a 1. Start up the quadrocopter again with
mode. level surface or correctly aligned. correct alignment
2. CF mode disrupted 2. Re calibrate CF mode (refer section on
CF calibration)

Schematic circuit board

Tail LED socket

LED socket (M4)

LED socket (M3)

Motor socket
Motor socket (M2, M3)
(M4, M1)

LED socket (M2)

LED socket (M1)

11
 Exploding View

Black A
forward
Black B

Green B
Green A

12
 Parts Listing

NO PART NAME QUANTITY

1 Propeller guard 4
2 Main rotor blade 4
3 Upper housing 1
4 Receiver board 1
5 Bearing 8

6 Battery cover 1

7 Battery 1

8 Electric motor 4

9 LED light 4

10 LED light cover 4

Lower housing 1
11
12 Carbon fibre spindle 4

13 Tail light plate 1

14 Bearing 4

15 Tail LED 1

16 Landing skid 2

Quadrocopter specifications

Length 375 mm
Height 58 mm
Blade length 136 mm
Battery Specification 3.7V 730mAh23C

Flight time 7-8 min

13
 Live Video Streaming and flight
control via WiFi
This quadrocopter comes with a WiFi camera already pre-installed. The device uses advanced image
compression technology to enable you to stream live video on your smartphone at a distance of 50 to 70
meters using WiFi.
To utilize this powerful Live video streaming feature and also flight control via smartphone , simply
download and install the app by scanning the QR code shown on following page matching to your
smartphone operating system.

Operating instruction:
To stream live video with WiFi camera, please ensure to take camera connector wire and plug it into the
appropriate socket with marking “WiFi” etched on quadrocotper housing. Socket is located adjacent to
camera. Please note, if connector wire is not correctly and securely inserted into the socket, live video
streaming feature will not work and may fail.
Power on your transmitter and the quadrocopter, and then the app on your smartphone.
From the Wi-Fi settings control on your smartphone, search for WiFi network name beginning with
“WiFiUFO” and enable connect ion.
Start the app and then press play on screen. The default app setting allows only for video transmission
but is disabled for flight control capability.
Mount the smartphone holder as per illustration on following page.
Place your smartphone on the smartphone holder, and use onscreen controls as shown below to stream
live video or take photos.
To use your smartphone to control flight of quadrocopter, simply press control switch button to
interchange between transmitter control/ phone control.

App Controls

Steering sensitivity value Gravity sensor mode

View file from folder Control switch (transmitter control /

Picture Video phone control)
Return Screen rotation

Elevator trim

Analog sticks

Rudder trim Aileron trim

Phone Holder assembly

WIFI Webcam Phone Holder

(Illustration)

QR code for QR code for

IOS (GooglePlay Android)
WIFI UFO WIFI UFO
(GooglePlay)
Technical specification

Function Specifications

Camera 0.3 megapixel

Video encoding format H.264

Video sampling rate of 25 to 30 frames per second

Image Resolution VGA (640*840)

Transmitting frequency range 2.412-2.484 GHz

Supports standard support WI-FI 802.11 b / g / n standards

Transmission bit rate 135/54/48/36/24/18/12/9/6 1M ( adaptive )

Throughput 90Mbps

Transmission power 135M: 15dBM

54M: 15dBM

11M: 19dBM

Receiver sensitivity 54/135M:-72dBM@10%PER

11M:-85dBM@8%PER

6M:-88dBM@10%PER

1M:-90dBM@8%PER

Safety standard WEP/WPA-PSK/WPA2-PSK

Transmission distance 50 to 150 m (varies depending on surrounding

electromagnetic interference)

Antenna Selection IPX 1 generation antenna interface

PCB size 33mm * 22mm * 0.8mm

Supply voltage 3-5V

Current consumption about 800mW

Operating temperature -10°C~+70°C