AR01.45-P-7555GZA Remove/install bottom part of oil pan 18.02.
2020
Engine 272, 273 in model 164
Engine 272, 273, 276 in model 251
P01.45-2200-09
Shown on model 164
1 Bolts 5 Left exhaust bracket 9 Bracket
2 Left catalytic converter 6 Right exhaust bracket 10 High pressure pipe
3 Bolts 7 Screw 11 Oil pan bottom section
4 Right catalytic converter 8 Engine mount 12 Screw
Danger Risk of death when working on component Do not touch damaged or defective live AS00.00-Z-0035-01A
parts and systems with U >= 30 V alternating component parts and lines or non-insulated
voltage (AC) or U >= 60 V direct voltage (DC) electrical connections and lines.
Danger Risk of death caused by vehicle slipping or Align vehicle between vehicle lift columns and AS00.00-Z-0010-01A
toppling off of the lifting platform. position the four support plates at the vehicle
lift support points specified by the vehicle
manufacturer.
Topical note Notes on self-locking nuts and bolts AH00.00-N-0001-01A
Remove/install
1 Remove windshield wiper system Engine 276.8 in model 251
AR82.30-P-6400RT
2.1 Remove air filter housing Engine 272 (except 272.973), 273 in model
164, 251
AR09.10-P-1150GZA
2.2 Remove left and right air filter housing with Engine 276.8 in model 251
right engine air intake duct upstream of air
filter
AR09.10-P-1150GQC
3 Remove power electronics with power Engine 272.973 in model 164.195
distributor
AR08.10-P-0011GZH
4 Put on engine hoist Model 164 AR33.10-P-0100-01GZ
Model 251 AR33.10-P-0100-01RT
Observe the manufacturer's assembly
specifications and safety information.
Model 251Bolt, partition wall *BA62.30-P-1008-01E
reinforcement between wheel well liners to
fender
Engine lifting device *240589006100
© Daimler AG, 1/14/21, L/10/20, ar01.45-p-7555gza, Remove/install bottom part of oil pan Page 1 of 4
Engine 272, 273 in model 164 Engine 272, 273, 276 in model 251
5 Drain engine oil, collect if necessary
Model 164, 251 with engine 272 AP18.00-P-0101PIT
Model 164, 251 with engine 273 AP18.00-P-0101RX
Model 251 with engine 276 AP18.00-P-0101W
Installation: Replace sealing ring.
6 Remove screw/bolt for (1) left CAT (2) and Engine 272
screw/bolts (3) right CAT (4) from exhaust
manifold
Engine 272 in model 164Bolt, flange *BA49.10-P-1002-01W
connection to exhaust pipe/exhaust manifold
Engine 272 in model 251Bolt, flange *BA49.10-P-1002-01X
connection to exhaust pipe or exhaust
manifold
7 Remove the screw/bolts for left exhaust Engine 272
bracket (5) and right exhaust bracket (6)
Engine 272 in model 164Bolt, catalytic *BA49.10-P-1001-01W
converter bracket to catalytic convertor
Engine 272 in model 251Bolt, catalytic *BA49.10-P-1001-01X
converter bracket to catalytic converter
8 Remove screw/bolts (7) of engine mounts (8) Model 164Screw/bolt, front engine mount *BA22.10-P-1001-03G
on front axle carrier to front axle carrier
Model 251Bolt, front engine mount to front *BA22.10-P-1001-03F
axle carrier
9 Lift engine Pay attention when lifting out engine that
no cables and lines are damaged and that
engine does not lean against the bulkhead.
10 Remove bracket (9) for high-pressure Engine 272, 273
lines (10) on oil pan bottom section (11)
Screw/bolt, power steering pressure line *BA01.45-P-1004-01M
to oil pan
11 Detach torsion bar from front axle carrier Model 251
AR32.20-P-0300RT
12 Remove screw/bolts (12) of oil pan bottom Engine 272, 273Screw/bolt, oil pan bottom *BA01.45-P-1003-01M
section (11) section to oil pan
ENGINE 276Bolt, oil pan bottom section *BA01.45-P-1003-01E
to oil pan
13 Loosen oil pan bottom section (11) from oil Model 164, 251
pan and remove.
Notes on sealant path for oil pan Engine 272, 273 in model 164 AH01.45-P-0001-01VA
Engine 272, 273 in model 251
Notes on sealant path for oil pan Engine 276 in model 251 AH01.45-P-0001-01MMA
Engine 276 in model 251 AR01.45-P-7500-04MM
If oil pan bottom section (11) cannot be
loosened from the oil pan, heat oil pan bottom
section (11) around sealing surfaces using a
heat gun. Then slide an assembly wedge
between sealing surface, to separate oil pan
bottom section (11) from oil pan.
Installation: Pay attention to sealant path
on oil pan bottom section (11).
Sealant, Loctite 5970, 50 ml *BR00.45-Z-1013-01A
Mounting wedge *110589035900
Application gun *112589002500
Clean
14 Clean sealing surfaces on oil pan bottom AR01.00-P-0050-01A
section (11) and oil pan
Do not use any sharp-edged tools or abrasive
paper.
The sealing surfaces can be damaged
otherwise.
Loctite 7200 *BR00.45-Z-1038-04A
Loctite 7063 (400 ml) cleaning spray *BR00.45-Z-1046-04A
15 Install in the reverse order
16 Read out fault memory using the diagnostic
system and clear if necessary
AD00.00-P-2000-04A
Warning Risk of accident from vehicle starting off by Secure vehicle to prevent it from starting off by AS00.00-Z-0005-01A
itself when engine running. Risk of injury itself. Wear closed and snug-fitting work
(bruises and burns) resulting from working on clothes. Do not touch hot or rotating parts.
the engine while it is being started or when it is
running.
© Daimler AG, 1/14/21, L/10/20, ar01.45-p-7555gza, Remove/install bottom part of oil pan Page 2 of 4
Engine 272, 273 in model 164 Engine 272, 273, 276 in model 251
17 Carry out engine test run, checking the engine
for leaktightness and proper operation
Oil pan
Number Designation Engine 276
BA01.45-P-1003-01E Bolt, oil pan bottom section to oil pan Nm 14
Oil pan
Number Designation Engine 272 Engine 273
BA01.45-P-1003-01M Screw/bolt, oil pan bottom section to oil pan Nm 9 14
Oil pan
Number Designation Engine 272 Engine 273
BA01.45-P-1004-01M Screw/bolt, power steering pressure M6 Nm 10 10
line to oil pan
Engine mount, engine support (engine side)
Number Designation Model 251
BA22.10-P-1001-03F Bolt, front engine mount to front axle carrier Nm 53
Engine mount, engine support (engine side)
Number Designation Model 164
BA22.10-P-1001-03G Screw/bolt, front engine mount to front axle carrier Nm 53
Exhaust system
Number Designation Engine 272, 273 in
model 164
BA49.10-P-1001-01W Bolt, catalytic converter bracket to catalytic convertor Nm 20
Exhaust system
Number Designation Engine 272, 273,
276 in model 251
BA49.10-P-1001-01X Bolt, catalytic converter bracket to catalytic converter Nm 20
Exhaust system
Number Designation Engine 272, 273 in
model 164
BA49.10-P-1002-01W Bolt, flange connection to exhaust pipe/exhaust manifold Nm 20
Exhaust system
Number Designation Engine 272, 273,
276 in model 251
BA49.10-P-1002-01X Bolt, flange connection to exhaust pipe or exhaust manifold Nm 20
Crossmember and front reinforcement
© Daimler AG, 1/14/21, L/10/20, ar01.45-p-7555gza, Remove/install bottom part of oil pan Page 3 of 4
Engine 272, 273 in model 164 Engine 272, 273, 276 in model 251
Number Designation Model 251
BA62.30-P-1008-01E Bolt, partition wall reinforcement between wheel well liners to fender Nm 10
112 589 00 25 00 240 589 00 61 00 110 589 03 59 00
Application gun Engine lifting device Mounting wedge
Repair materials
Number Designation Order number
BR00.45-Z-1013-01A Sealant, Loctite 5970, 50 ml A 003 989 98 20 10
BR00.45-Z-1038-04A Loctite 7200 Henkel AG & Co. KGaA
http://www.loctite.de
BR00.45-Z-1046-04A Loctite 7063 (400 ml) cleaning spray A 001 986 71 71 09
© Daimler AG, 1/14/21, L/10/20, ar01.45-p-7555gza, Remove/install bottom part of oil pan Page 4 of 4
Engine 272, 273 in model 164 Engine 272, 273, 276 in model 251
