Motherboard ASUS Z170MG MB V1.0-150606 Troubleshooting Guide
Motherboard ASUS Z170MG MB V1.0-150606 Troubleshooting Guide
Content
I. Baseband Troubleshooting Guide
1. System Block Diagram
2. Power Block Diagram
3. Power Domain and Power Sequence
2
ASUS Z170MG MB Service Manual
3. Power Domain and Power Sequence
3
ASUS Z170MG MB Service Manual
II. MB Trouble Shooting Guide
CTP connector
connector WIFI/BT/GPS/FM IC
GSM RF LCD connector
power amplifier LED driver
T-flash card
RF module Battery connector CPU FLASH socket
PMIC
GPS\WIFI ANT
USB
Earphone socket
MIC
4
ASUS Z170MG MB Service Manual
2. Cannot power on
Solution:
1 Check if the battery connector and its soldering are oxidized or damaged
2 Check if the following voltage, and GND has short circuit or abnormal voltage
VBAT 3.8--4.2V
VCORE 0.7--1.4V
VSYS 1.825/2.2V
VPA O.5-3.4V
VTXCO 2.8V
VA 2.8V
VCAMA 2.8V
VCN28 2.8V
VCAMA 2.8V
VUSB 3.3V
VEMC_3V3 3.3V
3 Check if start-up circuit is abnormal
4 If the start-up circuit is about 20 MA, check if the soldering of crystal oscillator circuit is normal
5 For those start-up current abnormally above 1A, check if VBAT circuit is shorted to ground, investigate each
locations’ grounding diodes and other key components
6 For those start-up current abnormally around 100MA, touch if there is any heating part on MB and focus on
their investigation
7 X-ray: check each main chip’s soldering, CPU/Flash/PMIC(MT6323GA)
8 Add soldering or re-solder each main chip and confirm again
9 Replace CPU/Flash/PMIC
CPU MT8382
PMIC Flash
5
ASUS Z170MG MB Service Manual
3. Blank screen
Solution:
1 Check if the backlight chip -- U815 driver chip has soldering deviation
2 Check the LCD connector’s assembly is normal, if not please re-assemble
3 Check if L801’s conduction is normal, and compare it to L1901 voltage on normal MB
4 Check if D803’s conduction is normal or the component’s soldering is reverse
5 Check if GPIO_FLASH_EN’s signal is normal, and adjust this signal’s backlight brightness
6 Check if VBAT’s power supply is normal
6
ASUS Z170MG MB Service Manual
Solution:
1 Re-assembly LCD or replace LCD, then reboot again to observe
2 Check if LCD and its soldering is abnormal
3 Check if LCD filter (Z801—Z805) is poorly soldered or damaged
4 X-ray: check if CPU’s soldering is abnormal
5 Add soldering or re-solder CPU, or replace it
L901
Backlight Z801—Z805
driver chip LCD connector
CPU
Solution:
1 Re-assemble or replace the CTP, then reboot to test again
2 Check if the CTP connector (J802) or its soldering is abnormal, re-solder or replace it to test again
3 Measure if VIO18_PMU’ voltage is normal
4 X-ray: check CPU’s soldering, add soldering or re-solder it to test again
5 Use a multi-meter to measure CTP test signal point, compare its ground resistance with normal MB’s
6 Replace CPU
7
ASUS Z170MG MB Service Manual
CTP connector
CPU
Solution:
1 Measure VIO18_PMU 1.8V C903 voltage
2 Add soldering or re-solder or replace the gravity sensor U903
3 Solder down U903, measure the corresponding pad’ ground impedance value compared to normal MB’s
4 X-ray: check CPU’s soldering, re-solder or replace CPU
U903
CPU
8
ASUS Z170MG MB Service Manual
7. Side key FPC failure
Solution:
1 Re-connect the side key FPC
2 Replace the side key FPC and test again
3 Check if KCOL0/KCOL1/POWERKEY ‘s voltage signal is normal
4 X-ray: check CPU (Volume Key) ’s soldering
5 Add soldering or re-solder or replace CPU
U601 CPU
9
ASUS Z170MG MB Service Manual
Solution:
1 Check if USB connector has soldering deviation or is poorly soldered, may replace USB and test again
2 Replace the battery and test again
3 Replace the battery connector and test again
4 Re-solder PMIC (U601)
PMIC U601
Solution:
1 Check if the rear camera is well assembled, re-assemble or replace the camera and again
2 Check if the rear camera’s J1005 B2B connector is damaged or poorly soldered, re-solder ore replace the
camera connector
3 Check VCAM_AF_PMU 2.8V/VCAMA_PMU 2.8V/VCMA_1 2.8V voltage
4 Check Z1003—Z1005 EMI filter is damaged or poorly soldered
5 Add soldering or re-solder or replace CPU
10
ASUS Z170MG MB Service Manual
Rear camera
connector
Filter
Solution:
1 Check if the front camera is well assembled, re-assemble or replace the camera and test again
2 Check if the front camera’s J1004 connector is damaged or poorly soldered, re-solder or replace the
connector
3 Check VCAMA-1 2.8V/VCAMA_IO_PMU 1.8V/VGP3_PMU 1.8V voltage is abnormal, if abnormal, check if
PMIC outputs abnormally, or if the peripheral circuit has short/ open circuit
4 Check if the front camera filter (Z1001—Z1002) is damaged or poorly soldered
5 Add soldering or re-solder or replace CPU
11
ASUS Z170MG MB Service Manual
EMI filter
Front camera
connector
Solution:
1 Measure VIBR_PMU MOT+、MOT- magnitude of voltage and compare to normal MB’s
2 Re-solder or replace the motor and test again
3 Replace the motor connector and test again
4 Re-solder or replace PMIC (U1601)
Motor connector
PMIC U601
12
ASUS Z170MG MB Service Manual
12. GSM network failure
Solution:
1 If GSM 850&900 RX fails, measure if L103/ L110/ L112 circuit are normal, re-solder or replace differential
transducer (U103)/ RF power amplifier (U102)/ RF transceiver (U203) in turn
2 If GSM 1800&1900 RX fails, measure if L105/ L111/ L113 circuit are normal, re-solder or replace differential
transducer (U103)/ RF power amplifier (U102)/ RF transceiver (U203) in turn
3 If GSM 850&900 TX fails, re-solder or replace RF power amplifier (U102)/ RF transceiver (U203) in turn
4 If GSM 850&900 TX fails, re-solder or replace RF power amplifier (U102)/ RF transceiver (U203) in turn
5 Add soldering or replace PMIC (U601)
6 Add soldering or replace CPU (U301)
13
ASUS Z170MG MB Service Manual
RF power amplifier
(U102)
GSM differential
transducer (U103)
CPU (U301)
RF transceiver
(U203) PMIC (U601)
14
ASUS Z170MG MB Service Manual
Solution:
1 If WCDMA 900 RX fails, re-solder or replace differential transducer (U204)/ RF power amplifier (U102)/ RF
transceiver (U203) in turn
2 If WCDMA 1900 RX fails, re-solder or replace RF power amplifier (U205)/ RF power amplifier (U102)/ RF
transceiver (U203) in turn
3 If WCDMA 900 TX fails, re-solder or replace differential transducer (U204)/ RF power amplifier (U201)/ RF
transceiver (U203) in turn
4 If WCDMA 1900 TX fails, re-solder or replace RF power amplifier (U205)/ RF power amplifier (U206) / RF
transceiver (U203) in turn
5 Add soldering or replace PMIC (U601)
6 Add soldering or replace CPU (U301)
15
ASUS Z170MG MB Service Manual
RF power amplifier
(U102)
U206 W1900
power amplifier U201 W950
CPU
power amplifier
X201 26M
crystal oscillator PMIC
U203 RF transceiver
16
ASUS Z170MG MB Service Manual
Solution:
1 Check the components’ soldering on WIFI/BT/GPS antenna circuit or the circuit are damaged
2 Check Filter (U1104) and its soldering is damaged
3 Measure VCN_1V8_PMU ,VCN_3V3_PMU voltage
4 Check if 26M crystal oscillator normally works, if the supply voltage VCN28_PMU is normal
5 Add soldering or re-solder or replace the chip (U1101 MT6627) and test again
6 Add soldering or re-solder or replace CPU U301 and test again
Solution:
1 Check if the filter (U1104) and its soldering is damaged
2 Check if the filter (U1103) and RF LNA chip (U1102) and their soldering are damaged
3 Measure if VCN_1V8_PMU voltage is normal
4 Check if 26M crystal oscillator normally works, add soldering or replace it and test again
5 Add soldering or re-solder or replace U1101 MT6627, and test again
6 Add soldering or re-solder or replace CPU U301, and test again
17
ASUS Z170MG MB Service Manual
16. FM failure
Solution:
1 Replace the earphone and test again FM function
2 Check if the earphone socket has soldering deviation, high floating or is damaged
3 Replace there is any component and its soldering is damaged on the earphone antenna circuit
4 Measure if VCN_2V8_PMU voltage is normal
5 Add soldering or replace 26M crystal oscillator
6 Add soldering or re-solder or replace U1101 MT6627, and test again
7 Add soldering or replace U301 MT6582
耳机座
X1101 26M
crystal oscillator
18
ASUS Z170MG MB Service Manual
17. Fail to identify earphone/Handset MIC failure
Solution:
1 Replace the earphone socket and test again the earphone function
2 Check if the earphone socket has soldering deviation, high floating or is damaged
3 Check if the related components of earphone are obviously poorly soldered or the earphone socket is
damaged
4 Measure EINT_15 HP voltage before and after the earphone cable is inserted; voltage before: 1.8V/ voltage
after: 0V
5 Replace the earphone socket and test again
6 Replace CPU (U301)
earphone
socket
19
ASUS Z170MG MB Service Manual
18. MIC no sound/small sound
Solution:
1 Measure if the main MIC’s supply voltage(MICBIAS0 R706) is normal
2 Visually inspect if MIC’s related tiny components (B705 & B706) and their soldering are damaged
3 Replace the MIC and test again, notice high temperature will damage the MIC when replacing
4 Add soldering or re-solder or replace PMIC (U601) PMIC and test again
主 MIC
20
ASUS Z170MG MB Service Manual
Solution:
1 Re-assemble or replace the receiver and test again
2 Visually inspect if the components on receiver circuit and their soldering are damaged
3 Add soldering or re-solder or replace U702 Audio PA
4 Add soldering or replace PMIC (U601) and test again
Solution:
1 Re-assemble speaker with connector or replace the speaker
2 Visually insect the related components and their soldering, such as the speaker connector
R708/B707/R710B708
3 Add soldering or re-solder or replace U702 Audio PA
4 Add soldering or replace PMIC (U601)
21
ASUS Z170MG MB Service Manual
Speaker connector
U702 AF PA
PMIC U601
Solution:
1 Re-insert or replace the SIM cards and test again
2 Visually inspect if the SIM card socket has soldering deviation, high floating or is damaged
3 Measure the SIM supply voltage (VSIM1_PMU ,VSIM2_PMU)
4 Add soldering or re-solder PMIC (U601)
22
ASUS Z170MG MB Service Manual
5 Add soldering or re-solder CPU (U301)
PMIC U601
Solution:
1 Re-insert or replace the T-flash card and test again
2 Visually inspect if the T-flash card socket has soldering deviation, high floating or is damaged
3 Measure the T-flash socket’s supply voltage (VIO18_PMU)
4 Re-solder or replace PMIC (U601)
5 Re-solder or replace CPU (U301)
CPU MT8382
T-flash card socket
PMIC U601
23
ASUS Z170MG
RF Hardware Trouble Shooting Guide
1
Z170MG RF Areas
2
Z170MG iRF Block Diagram: 2G/3G
(GSM&WCDMA)System
3
4
5
6
7
8
9
Key Components
10
11
TX Path: GSM&WCDMA
12
RX Path: GSM&WCDMA
13
Z170MG iRF Block Diagram:
GPS/WIFI/BT/FM System
14
15
16
17
18
Key Components
19
20
RX/TX Path: WIFI/GPS
21