Manual Mx-5000 Series

Installation and
Programming of
MX-5100, MX-5200, MX-5400
Fire Alarm Control Panels

The operation and functions

described in this manual are
available from Software Version
Mx5000-050-04 onwards.
Item Specification Details
Mx-5100 Mx-5200 Mx-5400
Enclosure Steel IP30 RAL7035 Steel IP30 RAL7035 Steel IP30 RAL7035
Dimensions H x W (/S) 340 x 340 x 85 (/M) 340 x 430 x 115 (/L) 470 x 450 x 115
x D mm (/M) 340 x 430 x 115 (/L) 470 x 450 x 115 (/D) 470 x 450 x 190
(/L) 470 x 450 x 115 (/D) 470 x 450 x 190
(/D) 470 x 450 x 190
Weight (excluding (/S) 6Kg (/M) 8Kg (/M) 8Kg
batteries) (/M) 8Kg (/L) 10Kg (/L) 10Kg
(/L) 10Kg (/D) 12Kg (/D) 12Kg
Temperature -5°C to 40°C -5°to 40°C -5°C to 40°C
Humidity (RH) 95 % Max 95 % Max 95 % Max
Cable Entries (/S) 13x top / 8x top rear (/M) 17x top / 11x top rear / 2 (/M) 17x top / 11x top rear / 2
(20mm knockouts) (/M) 17x top / 11x top rear / 2 bottom bottom
bottom (/L) 19x top / 11x top rear / 2 (/L) 19x top / 11x top rear / 2
(/L) 19x top / 11x top rear / 2 bottom bottom
bottom (/D) 30x top / 11x top rear / 3 (/D) 30x top / 11x top rear / 3
bottom bottom
AC Supply 200-240V +10%, -15% 200-240V, +10%, -15% 200-240V, +10%, -15%
(ratings marked on 47 –63 Hz AC 47 –63 Hz AC 47 –63 Hz AC
label inside panel 1.0A max 1.4A max 1.4A max
– see section 2.1
for location)
Battery Capacity 24V 4Ah Internal (min) 24V 4Ah Internal (min) 24V 4Ah Internal (min)
(/S) 24V 7Ah Internal (max) (/M) 24V 12Ah Internal (max) (/M) 24V 12Ah Internal (max)
(/M) 24V 12Ah Internal (max) (/L) 24V 18Ah Internal (max) (/L) 24V 18Ah Internal (max)
(/L) 24V 18Ah Internal (max) (/D) 24V 45Ah Internal (max) (/D) 24V 45Ah Internal (max)
Charging Current 1.0A Temperature 2.0A Temperature 2.0A Temperature
Compensated Compensated Compensated
Power Supply On-board 24V DC, 3A High On-board 24V DC, 5A High On-board 24V DC, 5A High
Efficiency Off-Line Switched Efficiency Off-Line Switched Efficiency Off-Line Switched
Mode Mode Mode
Output Voltage1 18.0V – 28.0V 18.0V – 28.0V 18.0V – 28.0V
Ripple (Vpkpk) 1.0V 1.0V 1.0V
Max Battery Ohms 1.6Ω ± 0.1 Ω 0.8Ω ± 0.1 Ω 0.8Ω ± 0.1 Ω
Imax(a)/ 1.6A 2.6A 2.6A
Imax(b)2 3.0A 5.0A 5.0A
Number of Fire 200 max 200 max, across 2 loops 200 max, across 4 loops
Zones (2000 when networked) (2000 when networked) (2000 when Networked)
Number of Loops 1 2 1 to 4
Devices per Loop Apollo 126 detector/call points per loop (max) Clause 6.2.5
Hochiki 127 detector/call points per loop (max)
VdS Not more than 128
devices per loop
Argus 240 detector/call points per loop (max)
Nittan 249 detector/call points per loop (max) 2095
Loop Current 3 500mA max. 500mA max. per Loop 500mA max. per Loop
Protocols Apollo: S90, XP95, Discovery, Explorer
Hochiki ESP
Argus Vega
Nittan Evolution
Sounder Outputs 3 2 x 1A Programmable 2 x 1A Programmable 4 x 1A Programmable
Relay Outputs 2 x1A 30VAC/DC (max) 2 x 1A 30V AC/DC (max) 2 x 1A 30V AC/DC (max)
(Programmable) 10mA 5V (min) 10mA. 5V (min) 10mA. 5V (min)
Auxiliary Output 3 4 24V DC, 500mA 24V DC, 500mA 24V DC, 500mA
Event Log 1000 Event & Diagnostic + 500 Fire

As our policy is one of constant product improvement the right is therefore reserved to modify product specifications without prior notice

1
Minimum/maximum specifications for the AUX, and Sounder outputs. Detector Loop voltage is not dependant on AC
or battery voltage.
2
Only applicable if the panel is configured to turn off the charger in alarm. Otherwise, Imax(b)=Imax(a).
3
Total output current from panel not to exceed Imax(b) less internal power consumption.
4
Aux supply tracks a maximum of 0.5V below battery terminal voltage when no mains supply is available.

Page 2 of 72
Table of Contents Page
1 INTRODUCTION __________________________________________________________ 6
1.1 Standards ____________________________________________________________ 6
1.2 Cautions and Warnings _________________________________________________ 7
1.3 Description ___________________________________________________________ 7
1.3.1 Mx-5000 Series ____________________________________________________ 7
1.3.2 Mx-5000N Series___________________________________________________ 7
1.4 EN54 Functions _______________________________________________________ 8
1.5 EN54 Optional Features with Requirements__________________________________ 9
1.6 Installation Approvals __________________________________________________ 10
1.6.1 Fire System Installations ____________________________________________ 10
1.6.2 Wiring Regulations ________________________________________________ 10
2 INSTALLATION__________________________________________________________ 11
2.1 Identification of Parts __________________________________________________ 11
2.1.1 Mx-5100_________________________________________________________ 11
2.1.2 Mx-5200_________________________________________________________ 12
2.1.3 Mx-5400_________________________________________________________ 13
2.2 Installing the Enclosure_________________________________________________ 14
2.2.1 Opening the Enclosure Cover ________________________________________ 14
2.2.2 Removing the Chassis______________________________________________ 14
2.2.3 Mounting the Enclosure _____________________________________________ 14
2.2.4 Remounting the Chassis ____________________________________________ 15
2.2.5 Recommended Cable Routing Arrangement_____________________________ 16
2.3 Loop Driver Installation _________________________________________________ 17
2.3.1 Fitting the cards ___________________________________________________ 17
2.3.2 Removing a Loop Driver Card ________________________________________ 18
2.4 Plug-In / Peripheral Bus Modules _________________________________________ 18
2.4.1 Routing Interface Card (Plug-In) ______________________________________ 18
2.4.2 2-Way Relay Card (Plug-In)__________________________________________ 19
2.4.3 Network Card_____________________________________________________ 19
2.4.4 Peripheral Module Chassis Mounting __________________________________ 20
2.4.5 VdS Interface Module Chassis Mounting________________________________ 21
2.4.5.1 Option Relay Card_______________________________________________________ 21
2.4.5.2 Optional Redundant Ring Controller _________________________________________ 21
2.5 Wiring Installation _____________________________________________________ 22
2.5.1 AC Mains Wiring __________________________________________________ 22
2.5.1.1 Cable Gland ___________________________________________________________ 22
2.5.2 Battery Installation _________________________________________________ 23
2.5.2.1 Small Enclosure ________________________________________________________ 23
2.5.2.2 Medium Enclosure_______________________________________________________ 24
2.5.2.3 Large Enclosure ________________________________________________________ 24
2.5.2.4 Deep Enclosure_________________________________________________________ 25
2.5.3 Detector Loop Installation ___________________________________________ 26
2.5.4 Sounder Circuits __________________________________________________ 27
2.5.5 Network Interface _________________________________________________ 28
2.5.6 Relay Circuits ____________________________________________________ 29
2.5.7 Auxiliary Supply Output _____________________________________________ 29
2.5.8 Isolated Peripheral Bus Interface______________________________________ 29
2.5.9 Switch Inputs _____________________________________________________ 30
2.5.9.1 Base Card _____________________________________________________________ 30
2.5.9.2 Display Card ___________________________________________________________ 30
2.5.10 RS232 Interface___________________________________________________ 30
2.5.11 USB Interface ____________________________________________________ 30
2.5.12 Routing Interface __________________________________________________ 31
2.5.12.1 Fire / Fault Routing ______________________________________________________ 31
2.5.12.2 Fire Protection Routing ___________________________________________________ 31
2.5.13 VdS Interface_____________________________________________________ 32
2.5.13.1 FAT / FBF Direct Connection ______________________________________________ 33
2.5.13.2 FAT / FBF Redundant Connection __________________________________________ 34
2.5.13.3 FSD Key Deposit Box Connection __________________________________________ 34
2.5.13.4 ÜE Fire Routing_________________________________________________________ 35
2.5.13.5 Fault Routing ___________________________________________________________ 35
Page 3 of 72
3 PROGRAMMING _________________________________________________________ 36
3.1 Introduction __________________________________________________________ 36
3.1.1 Access Levels ____________________________________________________ 36
3.1.2 Memory Lock _____________________________________________________ 36
3.1.3 Navigating through menus ___________________________________________ 36
3.1.4 Changing Text Descriptions __________________________________________ 37
3.1.5 Numeric data entry _________________________________________________ 38
3.2 Level 3 Menu Functions ________________________________________________ 38
3.3 Recommended Programming Procedure ___________________________________ 39
3.3.1 Loops ___________________________________________________________ 39
3.3.2 Loops – View/Edit__________________________________________________ 39
3.3.2.1 State __________________________________________________________________ 40
3.3.2.2 Type __________________________________________________________________ 40
3.3.2.3 Value _________________________________________________________________ 40
3.3.2.4 Zone __________________________________________________________________ 40
3.3.2.5 Meldergruppe Number (Mld) _______________________________________________ 40
3.3.2.6 Device Text ____________________________________________________________ 40
3.3.2.7 Action _________________________________________________________________ 40
3.3.2.8 Sensitivity ______________________________________________________________ 41
3.3.2.9 O/P Group _____________________________________________________________ 43
3.3.2.10 Additional Info___________________________________________________________ 43
3.3.2.11 Device Testing __________________________________________________________ 43
3.3.3 Loops – Auto Learn ________________________________________________ 44
3.3.3.1 Normal Procedure / Initial learn _____________________________________________ 44
3.3.3.2 Procedure if the Panel finds Devices Missing __________________________________ 44
3.3.3.3 Procedure if the Panel finds Devices Added ___________________________________ 44
3.3.3.4 Procedure if the Panel finds Devices Changed _________________________________ 45
3.3.4 Loop – Calibrate ___________________________________________________ 45
3.3.5 Loop - History _____________________________________________________ 45
3.3.6 Loop – Meter _____________________________________________________ 46
3.3.7 Loop – Scope _____________________________________________________ 46
3.3.8 Zones ___________________________________________________________ 47
3.3.9 Exit _____________________________________________________________ 47
3.3.10 Disable __________________________________________________________ 47
3.3.11 Enable __________________________________________________________ 47
3.3.12 View Options _____________________________________________________ 48
3.3.13 Passwords _______________________________________________________ 48
3.3.14 Time and Date ____________________________________________________ 48
3.3.15 PC Config________________________________________________________ 48
3.3.16 EN54-13 _________________________________________________________ 49
3.3.17 Setup ___________________________________________________________ 49
3.3.17.1 Network _______________________________________________________________ 49
3.3.17.2 Panel Zone _____________________________________________________________ 50
3.3.17.3 Service Number _________________________________________________________ 50
3.3.17.4 Service Due Date ________________________________________________________ 50
3.3.17.5 Trace Logging Mode _____________________________________________________ 50
3.3.17.6 Detector Blinking ________________________________________________________ 50
3.3.17.7 Earth Fault Notification ____________________________________________________ 51
3.3.17.8 Resound _______________________________________________________________ 51
3.3.17.9 Config Data ____________________________________________________________ 51
3.3.18 Display __________________________________________________________ 52
3.3.19 Panel ___________________________________________________________ 52
3.3.19.1 AC Fail Delay ___________________________________________________________ 53
3.3.20 Output Groups ____________________________________________________ 54
3.3.20.1 Default Output Settings ___________________________________________________ 54
3.3.20.2 Cause _________________________________________________________________ 55
3.3.20.3 Style __________________________________________________________________ 56
3.3.20.4 Copying Output Settings to Multiple Zones ____________________________________ 56
3.3.21 Investigation Delays ________________________________________________ 56
3.3.21.1 Overriding Delays at Level 1 _______________________________________________ 57
3.3.22 Test ____________________________________________________________ 57
3.3.23 LED Indications ___________________________________________________ 57
4 SERVICE AND MAINTENANCE _____________________________________________ 58
4.1 Maintenance Schedule _________________________________________________ 58
Page 4 of 72
 4.1.1 Daily Actions _____________________________________________________ 58
4.1.2 Monthly Actions ___________________________________________________ 58
4.1.3 Quarterly Actions __________________________________________________ 58
4.1.4 Annual Actions____________________________________________________ 58
4.2 Replacement of Components ____________________________________________ 59
4.2.1 Batteries ________________________________________________________ 59
4.2.1.1 Standby Batteries _______________________________________________________ 59
4.2.2 Liquid Crystal Display ______________________________________________ 60
4.2.3 Spares __________________________________________________________ 60
5 APPENDICES ___________________________________________________________ 61
5.1 Appendix 1 – Forgotten Level 3 Password __________________________________ 61
5.2 Appendix 2 – Recommended Fire Rated Cables _____________________________ 62
5.2.1 Detector Loop Lengths _____________________________________________ 62
5.2.2 Sounder Circuit Lengths ____________________________________________ 63
5.2.3 Fire / Fault Routing Circuit Lengths ____________________________________ 63
5.2.4 Network Cables ___________________________________________________ 63
5.3 Appendix 3 – Battery Standby Calculation Chart _____________________________ 64
5.4 Appendix 4 – Cause and Effect Programming Example________________________ 65
5.4.1 Introduction ______________________________________________________ 65
5.4.2 Output Groups ____________________________________________________ 65
5.4.3 Styles___________________________________________________________ 65
5.4.4 Output Group Programming _________________________________________ 66
5.5 Appendix 5 – Other Useful Documents_____________________________________ 67
5.6 Appendix 6 –Network Design Principles ____________________________________ 68
5.6.1 Mandatory Functions _______________________________________________ 68
5.6.2 Network Wiring ___________________________________________________ 68
5.7 Appendix 7 – Mx Series Product Capabilities / Max Limits ______________________ 69

Page 5 of 72
1 Introduction
1.1 Standards
Advanced Electronics Ltd declare that the products identified below conform to the essential
requirements specified in the Construction Products Directive 89/106/EEC:

0786-CPD-20952
EN54-2: 1997 +A1:2006
Control and indicating equipment for fire detection and fire
alarm systems for buildings

Provided options:
- Outputs to Fire Alarm Devices
- Output to Fire Routing Equipment
- Output to Fire Protection Equipment
- Output to Fault Routing Equipment
- Investigation Delays to Outputs
- Dependency on more than one alarm signal
- Fault Signals from Points
- Disablement of Points
- Alarm Counter
- Test Condition
- Standardised Input / Output

EN54-4: 1997 +A1:2002 +A2:2006

Power supply equipment for fire detection and fire alarm
systems for buildings

Mx-5100, Mx-5200, Mx-5400

Mx-5100N, Mx-5200N, Mx-5400N

In addition, the products comply with the following:

Low Voltage Directive 2006/95/EC

BS EN60950-1: 2006 Safety of information technology equipment

Electromagnetic Compatibility Directive 2004/108/EC

BS EN55022: 1998 Emissions, Class B
BS EN50130-4: 1996 +A2: 2003 Immunity, Product Family Standard

Page 6 of 72
1.2 Cautions and Warnings

BEFORE INSTALLATION – Refer To the Ratings shown on the label inside

the product and to the ‘Specifications Chart’ in this document.
STOP
Please read this manual carefully. If you are unclear on any point DO NOT
proceed. Contact the manufacturer or supplier for clarification and guidance.

Only Trained service personnel should undertake the Installation,

Programming and Maintenance of this equipment.

This product has been designed to comply with the requirements of the Low
Voltage Safety and the EMC Directives. Failure to follow the installation
instructions may compromise its adherence to these standards.
This equipment is constructed with static sensitive components. Observe anti-
static precautions at all times when handling printed circuit boards. Wear an
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
anti-static earth strap connected to panel enclosure earth point. Before installing
or removing any printed circuit boards remove all sources of power (mains and
SENSITIVE DEVICES

battery).

PC Where you see the “PC Only” symbol, these features can either only be set-up
using the PC Configuration Tool or there are additional options that are only
ONLY available via the PC Configuration Tool.

1.3 Description
This manual covers the installation, programming and commissioning of the Mx-5000 & Mx-5000N
Series Fire Alarm Control Panels. This manual provides generic programming and installation
information – Refer to the appropriate protocol application note for further and specific information
for each protocol.
Refer to the User Manual (Document No. 680-166) for details of how to operate the panel.

1.3.1 Mx-5000 Series

The Mx-5100 is a Single Loop, Analogue Addressable Fire Alarm Control Panel.
The Mx-5200 is a Two Loop, Analogue Addressable Fire Alarm Control Panel.
The Mx-5400 is a Multiple Loop, Analogue Addressable Fire Alarm Control Panel with provision for
up to four loops.
All above models are designed for use with the Apollo (Discovery, Explorer, XP95 and Series 90),
Hochiki (ESP) and Argus (VEGA) fire detection devices.

1.3.2 Mx-5000N Series

The Mx-5100N is a Single Loop, Analogue Addressable Fire Alarm Control Panel.
The Mx-5200N is a Two Loop, Analogue Addressable Fire Alarm Control Panel.
The Mx-5400N is a Multiple Loop, Analogue Addressable Fire Alarm Control Panel with provision for
up to four loops.
All above models are designed for use with the Nittan Evolution fire detection devices.
All panel models are available in a range of enclosure sizes and with a range of alternative optional
features.
Install the panel, detection loops, sounder circuits, etc. in accordance with the instructions in
Section 2 and then program the operation in accordance with the instructions detailed in
Section 3.

Page 7 of 72
1.4 EN54 Functions

This Fire Alarm Control Panel is compliant with the requirements of EN54-2 (1997)
and EN54-4 (1997) and EN54-13 (2005).
In addition to the basic requirements, the following optional functions are provided
and these comply with the requirements of EN54.

C.I.E Optional Functions EN54-2 Clause

Indication Outputs to Fire Alarm Devices 7.8
Outputs Outputs to Fire Routing Equipment 7.9
Controls Output to Fire Protection Equipment 7.10
Investigation Delays to Outputs 7.11
Co-incidence Detection 7.12
Type B & Type C
Alarm Counter 7.13
Fault Signals from Points 8.3
Output to Fault Routing Equipment 8.9
Disablement of Points 9.5
Test Condition 10
Standardised I/O 11

P.S.E Functions EN54-4 Clause

Operation from a main power supply 5.1

Operation from a standby battery 5.2
Monitor and Charge the Standby Battery 5.3
Recognise and Notify Supply Faults 5.4

System Functions EN54-13 Clause

Transmission Path Integrity 4.5

Networks (non hierarchical) 4.3

This Fire Alarm Control Panel also supports additional functions that are not covered
by EN54. These are as follows:
Refer to
Additional Function
Paragraphs

Auxiliary Power Supply Output 2.5.7

Auxiliary Relay Outputs 0
Programmable Cause / Effect on Outputs (Phased Evacuation) 5.4
Printer Option User Manual

Page 8 of 72
1.5 EN54 Optional Features with Requirements
In addition to the mandatory requirements of EN54 Part 2, the Control and Indicating Equipment
(C.I.E) supports the following optional features with requirements: -
Outputs to Fire Alarm Devices.

The C.I.E has provision for connection to Fire Alarm Devices. It is possible to Silence
and Resound the alarms at Level 2. Refer to the User Manual for further information.
Section 7.8
Refer to Sections 3.3.20 and 3.3.21 for information on output programming.

Outputs to Fire Routing Equipment.

The C.I.E has provision to signal the fire condition to a remote receiving station such
as the fire brigade office. Requires installation of a routing interface card. Refer to
Section 7.9
Sections 2.4.1/2.4.5, 2.5.12/2.5.13, 3.3.20, and 3.3.21 for further information.

Outputs to Fire Protection Equipment.

The C.I.E has provision to signal the fire condition to a remote receiving station such
as the fire brigade office. Requires installation of a routing interface card. Refer to
Section 7.10
Sections 2.4.1, 2.5.12, 3.3.20, and 3.3.21 for further information.

Delays to Outputs.

The C.I.E has provision for Output and Investigation Delays. Refer to Sections 3.3.20
Section 7.11 & 3.3.21 for further information

Coincidence Detection.

The C.I.E has provision for Coincidence Detection. Refer to Section 3.3.20 for further
Section 7.12 information. Types B and C are supported.

Alarm Counter.

The C.I.E has provision to record the number of times that the fire alarm condition is
Section 7.13 entered. Refer to the User Manual for further information.

Fault Signals from Points.

The C.I.E is able to receive and process fault signals from points. These are indicated
Section 8.3 on a per zone basis. Refer to the User Manual for further information.

Outputs to Fault Routing Equipment.

The C.I.E has provision to signal the fault condition to a remote receiving station such
as the service centre office. Requires installation of a routing interface card. Refer to
Section 8.9
Sections 2.4.1/2.4.5, 2.5.12/2.5.13, 3.3.20, and 3.3.21 for further information.

Page 9 of 72
 Disablement of Points.

The C.I.E has provision for enabling and disabling signals from points. Refer to the
Section 9.5 User Manual for further information.

Test Condition.

The C.I.E has provision for testing the installation on a per zone basis. Refer to the
Section 10 User Manual for further information.

Standardised Input/Output interface.

Standardised I/O interfaces are supported over the Ad-Net Network.

Section 11

1.6 Installation Approvals

1.6.1 Fire System Installations
The panel must be installed and configured for operation in accordance with these instructions and
the applicable code of practice or national standard regulations for fire systems installation (for
example BS5839-1: 2002) appropriate to the country and location of the installation.

1.6.2 Wiring Regulations

The panel and system must be installed in accordance with these instructions and the applicable
wiring codes and regulations (for example BS7671) appropriate to the country and location of the
installation.

Page 10 of 72
2 Installation
2.1 Identification of Parts
The following diagrams show the major parts of the panels.

2.1.1 Mx-5100
/S Enclosure comprises:
Back Box Door Back box

Base Card with 1x Loop AC Input

Driver mounted onto a

Chassis Plate
Door with Display Card Display
Cable
mounted onto a fascia
plate. Key-Lock. WARNING:HIGH VOLTAGE INSIDE
DO NOT REMOVE COVER
No Serviceable Parts Inside

Option for two key- Door

Lock
switches. Optional Key
Loop Driver

Switches Base Card Ratings Label

Display Chassis

Hinge Pin

/M Enclosure comprises:
Back Box
Door Back box
Display
Base Card with 1x Loop AC Input

Driver mounted onto a

Chassis Plate
Door with Display Card Display
mounted onto a fascia Cable

plate. Key-Lock. WARNING: HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

Option for eight key- Door

Lock
Optional Key
Switches Loop Driver
switches or four key- Base Card Ratings Label

switches and a printer. Chassis

Hinge Pin
Option for a 50-Zone LED Optional Zone

card.
LED Card

/L Enclosure comprises:
Back Box
Door Back box
Display
Base Card with 1x Loop AC Input

Driver mounted onto a

Chassis Plate
Door with Display Card
Display
mounted onto a fascia Cable

plate. Key-Lock. WARN ING:

DO NOT REM OV E C OVER

No Ser vic eabl e P arts Inside

HIGH VOLTA GE IN SID E

Option for eight key- Optional Key

Switches
switches or four key-
Loop Driver

Base Card Ratings Label

switches and a printer. Door Chassis
Lock

Option for two 50-Zone

LED cards.
Optional Zone
LED Cards

Hinge Pin

Page 11 of 72
2.1.2 Mx-5200
/M Enclosure
comprises:
Back Box
Base Card with 2x Loop Display
Door Back box

Drivers mounted onto a AC Input

Chassis Plate
Door with Display Card
mounted onto a fascia Display
Cable
plate. Key-Lock.
WARNING: HIGH VOLTAGE INSIDE

Option for eight key-

DO NOT REMOVE COVER
No Serviceable Parts Inside

Door Optional Key

switches or four key- Lock Switches
Loop Drivers 1-2 Ratings Label
switches and a printer. Base Card

Chassis
Option for a 50-Zone
LED card. Optional Zone
LED Card
Hinge Pin

/L, /D Enclosures
comprises:
Back Box
Door Back box
Display
AC Input
Base Card with 2x Loop
Drivers mounted onto a
Chassis Plate
Door with Display Card
mounted onto a fascia Display
Cable

plate. Key-Lock. WARNING: HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

Option for eight key- Optional Key

Switches
Loop Drivers 1-2
switches or four key- Base Card

switches and a printer. Door

Lock Chassis
Ratings Label

Option for two 50-Zone

LED cards.
Optional Zone
The deep (/D) LED Cards

enclosure arrangement
is identical. Hinge Pin

Page 12 of 72
2.1.3 Mx-5400
/L, /D Enclosures
comprises:
Back Box
Base Card with 1-4 Display
Door Back box

Loop Drivers mounted AC Input

onto a Chassis Plate

Door with Display Card
mounted onto a fascia
plate. Key-Lock. Display
Cable

Option for eight key- WARNING:HIGH VOLTAGE INSID

DO NOT REMOVE COVER

switches or four key-

No Serviceable Parts Inside

Optional Key
Switches
switches and a printer.
Loop Drivers 1-4
Door
Option for two 50-Zone Lock Base Card

Chassis
LED cards. Ratings Label

The deep (/D)

enclosure arrangement Optional Zone
LED Cards

is identical.
Hinge Pin

Page 13 of 72
2.2 Installing the Enclosure
The panel weight is heavy when the batteries are installed. Use the appropriate fixing
hardware to secure the panel to the wall. Observe recommended lifting practices to guard
against spinal injury. See table below for maximum weights.

Enclosure Weight Maximum Battery Overall Maximum Weight

/S 6kg 7Ah 2.5kg 11kg
/M 8kg 12Ah 3.9kg 16kg
/L 10kg 18Ah 5.7kg 22kg
/D 12kg 45Ah 15.5kg 43kg

2.2.1 Opening the Enclosure Cover

The enclosure covers are provided with a key-lock assembly for securing the hinged door to the
back box. Insert and turn the key anti-clockwise to open the enclosure.

2.2.2 Removing the Chassis

It is recommended that the chassis be removed before fitting the panel to the wall. To remove the
chassis:
Disconnect the earth cable connecting the chassis to the spade terminal on the rear enclosure.
Unplug the 3-way connector feeding the AC supply to the Base Card.
Disconnect the ribbon cable connecting the display to the base card at the display.
Loosen the two screws holding the chassis to the back box. There is no need to remove these
screws fully – the chassis plate has keyhole style mounting holes. Carefully remove the chassis
from the rear enclosure and place in a safe place to prevent accidental damage.

Do not lift the chassis by holding onto any of the printed circuit cards. Hold the chassis by the
metal plate only.

2.2.3 Mounting the Enclosure

Firstly, remove the required knockouts for the installation wiring. There are sufficient knockouts on
the top of the enclosure for all installation wiring. In addition, there are knockouts at the top of the
back wall, if required, for rear entry cabling.
The enclosure is provided with three fixing points. 340
The diagrams opposite and below show the
positions of the three holes and dimensions of each
enclosure. Use all three positions to ensure the
panel is held securely to the wall.
Drill the required holes in the supporting wall using a
drill bit diameter 7.0 mm and plug with a suitable
40mm or longer expansion plugs. Affix the panel to
the wall with M5 screws or No.10 screws. Use
299
340

appropriate fixings to support the weight including

the batteries.
Ensure that there is sufficient space to allow the
26

door to be opened when the panel is mounted.

Finally, use a brush to remove any dust or swarf
from inside the enclosure.
135 135

(/S) Enclosure Size and Fixing Point Dimensions

Page 14 of 72
 427

(/S) Enclosure Size and knockouts (top)

340

271
299
Knockouts x2

26
(/M) Enclosure Size and knockouts (top)

183.5 183.5

(/M) Enclosure Size and Fixing Point Dimensions

447

(/L Enclosure Size and knockouts (top)

472

378
431
(/D Enclosure Size and knockouts (top)

Knockouts
/L x2, /D x3

183.5 183.5
26

(/L, /D) Enclosure Size and Fixing Point Dimensions

2.2.4 Remounting the Chassis

Carefully replace the chassis and fix into place using the two screws.
Reconnect the chassis earth cable to the spade terminal in the rear of the enclosure, reconnect the
display cable to the display card and then reconnect the AC supply lead to the Base Card.

Page 15 of 72
2.2.5 Recommended Cable Routing Arrangement
It is recommended
that the typical
routing arrangement AC INPUT

shown in the diagram

opposite be
employed. LOOPS AUX, PBUS & SW I/P RELAYS SOUNDERS

Segregate the low

AC Input
voltage wiring (Loop
Circuit, Sounder
Circuits and AUX
Supply) from the AC
Mains Wiring.
Segregate any wiring
connected to the Loop 1 Loop 2 Loop 3 Loop 4 AUX PBUS RLY1 RLY2
SW I/P
SND
1&2
SND
3&4

relay contacts.
Refer to Appendix 2 –
Recommended Fire
Rated Cables for
further information on WARNING:HIGH VOLTAGE INSID
DO NOT REMOVE COVER

cable types to be
No Serviceable Parts Inside

used.
Refer to specific
sections on how to Loop Drivers 1-4
install AC Mains input
and loop, sounder, Base Card
relay and AUX Chassis AC Input –
outputs circuits. Alternative
route behind
chassis and
use bottom
knockout

Internal arrangement showing recommended routing of cables.

Page 16 of 72
2.3 Loop Driver Installation
The Mx-5100 and Mx-5100N panels are factory fitted with one loop driver.
The Mx-5200 and Mx-5200N panels are factory fitted with two loop drivers.
The Mx-5400 and Mx-5400N panels can be fitted with up to four loop drivers – factory fitted with one
loop driver.

2.3.1 Fitting the cards

To extend the number of detector loops or to
replace an existing loop driver card follow the
NITTAN
procedure described below.
Examples of the loop drivers are shown opposite.
These cards are populated with components on
both sides of the cards – the main side view is
shown for both examples.

Isolate ALL sources of power before APOLLO / HOCHIKI / VEGA

installing or removing printed circuit
boards.

Observe anti-static precautions at all

times when handling printed circuit
boards.
Loop Driver – Main Component Side View
A section of the Base Card identifying the Ensure that the pins of the connectors are
locations for each loop driver is shown in the correctly aligned. The loop driver should be
pictures below. inserted with the main component side of the
board placed on the left-hand side. The Base
To install a loop driver, operate the locking tabs of
Card can accept from one up to four loop driver
the card guides, then gently guide the loop driver
cards – it does not matter which positions are
printed circuit card into the card guide slots and
used. Ensure that the detector loop wiring is made
then push into place onto the connector on the
to the terminal block positions appropriate to the
Base Card.
loop driver cards actually installed.

1-LOOP CARD 2-LOOP CARD 4-LOOP CARD

Loop positions are numbered 1 – 4 from the left hand side.

Page 17 of 72
2.3.2 Removing a Loop Driver Card
To remove a loop driver, remove all power and follow the procedure above but:
Take a firm hold of top of the loop driver card. Gradually and carefully pull the loop driver vertically
away from the base card and guide it out of the slots in the card guides.

2.4 Plug-In / Peripheral Bus Modules

All panels provide provision for installation / use of local peripheral cards to provide additional
functions. The peripherals are connected via an isolated bus interface.
Each panel supports either a plug-in 2-Way Relay card or a plug-in General Routing Interface card
(peripheral bus module).
All panels also support the connection of up to sixteen Mxp-034 4-Way Programmable Sounder
Modules 5, up to sixteen Mxp-035 4-Way Programmable Relay Modules and other peripheral bus
modules housed in separate enclosures. All panels except the small enclosure (/S) support the
mounting of one peripheral module on the chassis plate.
Refer to the wiring installation section (2.5.8) for details of how to connect the peripheral modules
and section (2.5.5) for details of the network connections.

2.4.1 Routing Interface Card (Plug-In)

Outputs to Routing Equipment – Clauses 7.9 and 8.9.
Output to Fire Protection Equipment – Clause 7.10
The Routing Interface Card provides monitored outputs for connection to
Fire Routing Equipment (Item E) and Fault Routing Equipment (Item J)
or to Fire Protection Equipment (Item G) in accordance with EN54-2.
The Mxp-532 Interface
card is fitted to the M3 Screw Interface Card
base card using 1x M3
screw and 3x plastic
pillars. A metal pillar is
pre-fitted to the base
card. Refer to the
diagram opposite.
All signals and power
required for operation
of the card are
provided on the plug-in WARNING:HIGH VOLTAGE INSIDE
DO NOT REMOVE COVER
No Serviceable Parts Inside

connections.
Ensure that the
connections are
correctly aligned. Plastic Spacers

The screw fixing is

essential for EMC
Mounting Position for the Routing Interface Card
Immunity protection.

Isolate ALL sources of power before installing or removing printed circuit boards.

Observe anti-static precautions at all times when handling printed circuit boards.

5
The Mxp-034 and Mxp-035 modules must be configured using the PC CONFIG TOOL. A maximum of 32 modules (of any
type) can be connected only. Refer to the installation guides provided with each module for further details.
Page 18 of 72
2.4.2 2-Way Relay Card (Plug-In)
The Mxp-507 Relay 2-Way Relay
card is fitted to the
base card using 2x
plastic pillars. Refer
to the diagram
opposite.
All signals and
power required for
operation of the
card are provided WARNING:HIGH VOLTAGE INSIDE
on the plug-in DO NOT REMOVE COVER
No Serviceable Parts Inside

connections.
Ensure that the
connections are Plastic Spacers
correctly aligned.
Mounting Position for the 2-Way Relay Card

Isolate ALL sources of power before installing or removing printed circuit boards.

Observe anti-static precautions at all times when handling printed circuit boards.

2.4.3 Network Card

An Mxp-503 (STD) or an Mxp-509 (FT) Network Card can be installed onto the base card.
The card is fitted to
the base card using
1x M3 screw and 3x
plastic pillars. A Network Interface
Ribbon Cable M3 Screws
metal pillar is pre-
fitted to the base
card. Refer to the
diagram opposite.
All signals and
power required for
operation of the
card are provided
on the plug-in
connections. WARNING:HIGH VOLTAGE INSIDE
DO NOT REMOVE COVER
No Serviceable Parts Inside

Plug the ribbon

cable into the
connector as
shown. Plastic Spacers

The screw fixing is Mounting Position for the Network Card

essential for EMC
Immunity
protection.

Isolate ALL sources of power before installing or removing printed circuit boards.

Observe anti-static precautions at all times when handling printed circuit boards.

Page 19 of 72
2.4.4 Peripheral Module Chassis Mounting
A Peripheral Module can be installed onto the chassis plate in the medium, large and deep
enclosures.
The peripheral card is fitted to the chassis using 4x M3 screws.
All cards require connections to a 24V DC supply (AUX 24V) and to the PBUS communications.
Refer to wiring section for further information.
The screw fixing is essential for EMC Immunity protection.

Power and Data

Route along edge of chassis and tie
in place with tie-wraps.

WARNING: HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

Mxp-034 Base Card (2-LP shown)

Mounting Position on Chassis – MXP-034 4-Way Sounder shown.

Isolate ALL sources of power before installing or removing printed circuit boards.

Observe anti-static precautions at all times when handling printed circuit boards.

Page 20 of 72
2.4.5 VdS Interface Module Chassis Mounting
An Mxp-504 VdS Interface Module can be installed onto the chassis plate in the medium, large and
deep enclosures.

Outputs to Routing Equipment – Clauses 7.9 and 8.9.

The Routing Interface Card provides monitored outputs for connection to
Fire Routing Equipment (Item E) in accordance with EN54-2.

This card also provides a serial interface and power to FAT and FBF devices and an interface to
an FSD key deposit box adaptor.
The circuit card is fitted to the chassis using 4x M3 screws.
The screw fixing is essential for EMC Immunity protection.
All signals and power required for operation of the card are provided on the ribbon cable
connections.

WARNING: HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

VdS I/F Ribbon Cable Base Card (2-LP shown)

Mounting Position on Chassis.

Isolate ALL sources of power before installing or removing printed circuit boards.

2.4.5.1 Option Relay Card

An optional Mxp-508 (8-Way Relay Card) can be mounted on top of the interface card to provide
additional relay output circuits. Use the supplied pillars to secure the Interface card to the chassis
using the lower 4 mounting holes. Mount the relay card onto the pillars using the supplied M3
screws and connect the ribbon cable between PL1 on the relay card and PL3 on the interface
card.

2.4.5.2 Optional Redundant Ring Controller

An IFAM ADP-N3E Redundant Controller (Master) or ADP-N3S (Slave) can be installed alongside
the VdS Interface card to provide a redundant ring transmission path to FAT and FBF devices.
In the /D enclosure, this circuit card can be fitted to the enclosure sidewall using 4x M3 screws.
For other enclosure sizes, the card must be mounted in a separate enclosure that is connected to
the panel via rigid conduit and must be located ≤ 3 metres from the panel.
See Section 2.5.13.2 for wiring connection information.

Page 21 of 72
2.5 Wiring Installation
All electrical wiring installation work should be carried out in accordance with the code of practice or
applicable national standards appropriate to the country of installation.
To maintain electrical integrity of the SELV wiring on the input, output, loop and communications
lines all SELV wiring should be segregated from the LV mains wiring and be wired using cable with
insulation suitable for the application.
To minimise the effects of EMC interference all data wiring circuits should be wired with a twisted
pair of conductors with a cross sectional area suitable for the loading conditions.
In areas where cabling may come into contact with high frequency interference, such as portable
radio transceivers etc. the data wiring cable should be of a twisted pair construction within an overall
screen. Care should be taken to correctly terminate this screen, refer to the appropriate sections of
this manual for further information for each circuit type.
NB: Minimum / Maximum cable size for all external connections is limited to 0.5mm² / 2.5mm² (22-
14AWG).

2.5.1 AC Mains Wiring

Route the high voltage mains AC wiring into the
enclosure at the upper right corner only. Keep the
AC wiring away from the circuit boards and all Panel Wiring
other wiring. Brown
FUSE 3.15A
LIVE
Green
EARTH
The panels must be connected to
the supply earth through the power
Blue NEUTRAL
Must be cable.
earthed

AC Mains terminations
The mains input connector is shown in the
diagram opposite. Note the positions of the earth,
neutral and live terminal connections. These are The fuse is rated as follows:
clearly marked on the label next to the connector.
The connector block contains an integral fuse T 3.15A H 250V
holder.
Replace with correct rating and specification only.
Secure the mains input wiring by tie wrap as close
to the terminal block as possible.
Connect the Control Panel to the mains supply via
a readily accessible disconnect-device (Isolation
Switch) and suitable earth fault protection
incorporated in the building installation wiring. The
Mains cable should be 0.75mm2 cable rated at
250V and fused via a 5A anti-surge fuse.

2.5.1.1 Cable Gland

The cable gland and any cord clamp bushings used in routing the Mains cable through the
20mm knockout must have a minimum flame-retardant rating of 94HB.
Suggested glands and bushings are: -
Type Manufacturer
Gland IP65 – Brass M20, EExd / Eexe Lappcable
Gland IP68 – Nylon 66 M20 Black, UL94V2 Multicomp
Bushing – Nylon 66 M20 Black, UL94V2 Multipcomp

Page 22 of 72
2.5.2 Battery Installation
The panel requires two 12V Base Card Terminations
batteries for standby operation.
The battery leads are connected
onto the base card via a two-part
plug and socket, as shown in the
diagram opposite.
Refer to the Specifications for
minimum and maximum battery WARNING: HIGH VOLTAGE INSIDE
DO NOT REMOVE COVER
sizes allowed. No Serviceable Parts Inside

OBSERVE POLARITY OF
CONNECTIONS!
Note: Either of the positive
connections can be used on the
terminal block.

Link Cable BLACK

Place the batteries in the bottom of the enclosure
and connect the ‘Red’ lead to the positive (+) -
terminal of battery #1 and the ‘Black’ lead to the
negative (-) terminal of battery #2. Connect the +
negative of battery #1 to the positive of battery #2
using the supplied link cable. RED

Ensure that the battery terminals do not short out + - + -

against any part of the enclosure, circuit board or #2
#1
chassis plate.

Do not make the final battery connections until the installation wiring is completed and the
system is to be powered up.
Always connect the AC Mains input before connecting the battery.

New batteries require ‘top-charging’ before installation. Refer to Section 4.2.1.1 for a list of
recommended batteries.

2.5.2.1 Small Enclosure

The diagram opposite shows the
recommended location and orientation
for the 7AH batteries within the panel.

WARNING:HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

Page 23 of 72
2.5.2.2 Medium Enclosure
The diagrams opposite show the
recommended location and orientation
for 7Ah – 12AH batteries within the
panel.

WARNING:HIGH VOLTAGE INSIDE

DO NOT REMOVE COVER
No Serviceable Parts Inside

2.5.2.3 Large Enclosure

The diagrams opposite show the
recommended location and orientation
for 7Ah – 17AH batteries within the
panel.

WARNING:HIGH VOLTAGE INSID

DO NOT REMOVE COVER
No Serviceable Parts Inside

Page 24 of 72
2.5.2.4 Deep Enclosure
The diagrams opposite show the
recommended location and orientation
for 7Ah – 38AH/45AH batteries within the
panel.

WARNING:HIGH VOLTAGE INSID

DO NOT REMOVE COVER
No Serviceable Parts Inside

Page 25 of 72
2.5.3 Detector Loop Installation
Maximum of 32 Sensors / Call Points in a Zone (between Isolators).

The Detection Loop Circuit should be installed as a continuous Clause 6.2.5

loop with isolator modules such that a short circuit condition VdS Not more than 128
devices per loop
does not remove more than one zone or 32 input devices. 2095
Section 12.5.2

Not more than 512 fire detectors and / or manual call points and their associated
mandatory functions shall be affected as a result of a system fault in the C.I.E.

The panel should be installed with not more than 512 fire input devices.
Section 13.7 See Appendix 9 for further details on network installations.

Form the loop starting at the Loop Out + and –

terminals on the base card.

OUT –
OUT +
Route the wires around the loop connecting all

IN +
IN –
devices in accordance with the manufacturers’
data sheet supplied with each unit.
Ensure that the devices are correctly installed with
regard to their positive and negative terminal
polarity (especially Loop Isolator Modules).
Connect the return wires to the Loop IN + and –
terminals on the base card. Base Card Terminations (Typical).
The diagram opposite shows the typical
arrangement of the loop connections on the base
cards.
Refer to Section 2.3 for details on installing
additional loop drivers on the multi-loop panels.

When screened cable is used, it is vital to connect the screen / drain wire to the chassis / earth at
the cable gland input / earth stud in the panel. Always ensure that all segments of the cable loop
have continuity of the screen and take care to ensure that the screen is not exposed to any other
earth point (e.g. metalwork, cable trays, junction boxes, etc.).
The Loop Driver Circuit on the Base card is Isolators
equipped with in-built isolators to take care of
short circuit conditions on the wiring between the -
panel and the first device on the loop. Do not fit +
loop isolators at the panel outputs.
The diagram opposite shows a typical loop -
arrangement. +
Maximum recommended cable loop length is 1500
to 2000 Metres. Refer to Appendix 2 – Typical Loop Arrangement.
Recommended Fire Rated Cables for further
information on cable types to be used.

Take care that the voltage drop at full load is within the detector rating – refer to the detector
manufacturers’ data sheet for minimum values.
To maintain signal line wiring supervision, break the wiring run at each loop device.

The loop circuits support monitoring with an Active EOL device (embedded on the
loop driver) to ensure circuit integrity in accordance with the requirements of EN54-
13.

Page 26 of 72
2.5.4 Sounder Circuits
The Mx-5100 & Mx5200 are equipped with two
supervised sounder circuits. These are denoted
as Circuits A and B.

B+
A–

B–
A+
The Mx-5400 is equipped with four supervised
sounder circuits. These are denoted as Circuits A,
B, C and D.
Each Sounder output is rated at a maximum of
1 Ampere.
The terminal connections on the base card are
shown in the diagram opposite. Base Card Connections – Typical.
The sounder outputs are monitored (supervised)
for open and short circuit conditions using reverse
polarity signals. Sounder must be equipped with -

EOL
an in-built blocking diode that prevents the +
sounder from taking power when the output is in
the supervising condition.
Typical
An End-of-Line Resistor (EOLR) of value 6200Ω, Arrangement
½ Watt must be fitted to the last sounder / bell.
Refer to Appendix 2 – Recommended Fire Rated Typical Sounder Arrangement.
Cables for further information on cable types to be
used.

When screened cable is used, it is vital to connect the screen to the chassis / earth at the cable
gland input / earth stud in the panel. Always ensure that all segments of the cable loop have
continuity of the screen and take care to ensure that the screen is not exposed to any other
earth point (e.g. metalwork, cable trays, junction boxes, etc.).

The sounder outputs support monitoring with an Active EOL device to ensure
circuit integrity in accordance with the requirements of EN54-13.

The sounder circuits can be configured for

compliance with EN54-13 by programming and
the use of an Active EOL device. All panel -
Active
EOL

sounder outputs must be fitted with the Active +

EOL device (Mxp-505)
The panel uses techniques to ensure that a fault Typical
warning condition is reported if the circuit Arrangement
resistance increases to a condition where the
voltage at the last device may fall below its
Typical Sounder Arrangement.
minimum operating voltage level. This is
compatible for load currents from minimum up to OBSERVE POLARITY
maximum (1 ampere).
The Active EOL device is polarity
Install the Active EOL device at the end of the sensitive.
sounder circuit instead of the normal EOL resistor
– this device is polarity sensitive. Connect the Red The Active EOL is fuse protected –
lead to the sounder + signal line. however, if connected incorrectly
and the sounder circuit is activated,
the fuse will open and is not user
replaceable.

Page 27 of 72
2.5.5 Network Interface
The network permits the connection of other panels,
SCN
remote terminals and other devices to complete a B A
distributed system. A B
SCN
Either an Mxp-503 (STD) standard network interface
card or an Mxp-509 (FT) fault tolerant network
interface card must be installed in the panel. All
network nodes must be installed with the same type
IN OUT
of interface.
Cable must be twisted pair 18AWG or 20AWG.
To Base Card

Screened type cable is recommended (e.g. Belden

8760, 8762). Connect the screen to the designated
terminal block positions only.
Each interface card has independent connectors for
the outgoing and incoming network cable. Using a
twisted-pair cable, connect from the “OUT” socket
on the first panel to the “IN” socket on the next
panel as follows.

Screen Screen
OUT B B IN
A A

STD (Up to 32 nodes)

The “IN” terminals on the first node and the “OUT” STD
ELR 150ohm ½ W ELR 150ohm ½ W

terminals on the last node are not used. Connect an

ELR (150Ω) resistor between A and B on the IN O UT IN OUT IN O UT IN OUT
terminal blocks of the unused sockets.
Maximum cable length (overall length) is 1500m
using recommended cables. 1500m

FT (Up to 200 nodes)

Other Network devices must be fitted with a FT type FT

adaptor card. 1500m

Install a cable from the last node “OUT” terminals

IN O UT IN OUT IN O UT IN OUT
back to the first node “IN” terminals to form a ring.

Maximum cable length between nodes is 1500m

using recommended cables. Maximum cable length 20000m (m ax)

(overall length) is 20000m using recommended

cables.

Page 28 of 72
2.5.6 Relay Circuits

Fault Output.

Relay 1 is arranged for failsafe operation as standard.

Section 8.8
The Mx-5000 Series are equipped with two relay RELAY 1 RELAY 2
outputs. These are normally programmed to

COM
COM
activate on Fault and Fire Alarm conditions

NO

NO
NC
NC
respectively.
Each output is unsupervised with volt-free
changeover contacts rated at 30V AC/DC,
1 Ampere, resistive.
An Optional plug-in 2-Way relay card is available if
additional relays are required (Relays 3 & 4).
Base card connections
Optional peripheral bus relays cards are also
available.
The Relay outputs can be used, instead of the Routing Interface Card, to provide non-monitored fire
and fault routing outputs to appropriate routing equipment.
In this case, the panel will not indicate transmission path failures to the routing equipment – this feature
must be incorporated into the routing equipment itself. [Not fully EN54-2 compliant].

2.5.7 Auxiliary Supply Output

The Mx-5000 Series are equipped with an AUX PBUS SWITCH

auxiliary 24V DC, 500mA power supply output.

+24V

COM
0V

This can be used for powering ancillary equipment SW

A

and must only be used for powering localised /

internal equipment.

Base Card connections

2.5.8 Isolated Peripheral Bus Interface

The isolated bus interface is used to connect local AUX
PBUS SWITCH
peripheral equipment located internal to the panel
or located within 10m of the panel.
+24V

COM
SW
0V

A
B

The terminal block on the Mx-5000 Series base

card is shown opposite. Connect the cable from 'A'
to 'A' and from 'B' to 'B'. Equipment is connected
via a daisy chain.
External connections should be made using fire
rated cable or run in rigid metal conduit between
enclosures. Base Card connections

PC Peripheral Bus modules must be Panel Base Card Peripheral Module Peripheral Module Peripheral Module

O N LY
configured using the PC Tool TB TB TB

A B
Last Module – FIT
EOL Jumper to IN

To External Modules B A B A B A B A B A B A

Page 29 of 72
2.5.9 Switch Inputs
2.5.9.1 Base Card AUX PBUS
SWITCH
One Switch input is provided on the base card

COM
(I/P9) and up to eight key switch inputs (I/P1-8)

SW
+24V

0V
are provided on the display card.

B
These can be used for changing access level,
performing “class change” etc. by changing the
“Action” of these inputs.
Refer to separate Application Notes for examples.
The base card switch input is a monitored circuit –
Base Card Connections.
EOL = 10KΩ, Active Resistance = 470Ω

2.5.9.2 Display Card

Optional key switches (volt-free) are available to
be mounted on the panel fascia plate. These are
pre-wired with the appropriate 2-pin connector.
Using a sharp knife, cut through the fascia label
using the aperture profile as a template. Insert the
Optional Key
switch mechanism and tighten the nut. Route the Switches
wiring as shown and plug into the connector.
Program the required function.
--87654321

The fascia label is provided with a slide-in label

pocket for a user text
description. Position
Slide-in label Route the switch cables
along the bottom of the
fascia plate and fix with
The switch cable 10 9 8 7 6 5 4 3 2 1 tie-wraps to the return Switch Input
flange.
Connector
connector plugs into
the display card
connector as show Display Plate Arrangement (Typical).
opposite. Not Used

2.5.10 RS232 Interface

The Mx-5000 Series are equipped with an isolated
GND

RS232 I/F Circuit at the bottom of the base card.

RX
TX

The terminal block connections are shown

opposite. RS232

TX = Transmit Data from the panel, RX = Receive

Data into the panel, GND = Ground Reference.
This interface can be used for connection to a
modem, pager interface, PC or external printer.
Base Card Connections – typical.

2.5.11 USB Interface

The Mx-5000 Series are equipped with an isolated USB I/F Circuit at the bottom left of the base card.
This can be used for connection to a PC for use of the PC Configuration Tool.
The USB Interface uses common signals with the RS232 Interface – plugging in a USB connection
disconnects and isolates the RS232 Interface.

Page 30 of 72
2.5.12 Routing Interface
PC The Plug-In Routing Interface is used to
output monitored signals to Fire Routing
O N LY
Equipment and Fault Routing Equipment
or to Fire Protection Equipment.
2.5.12.1 Fire / Fault Routing
Each function comprises of an output circuit and
an input (confirmatory) circuit.
MONITORED
Each output is monitored for open circuit and short INPUT CIRCUIT
circuit wiring conditions in both the activated and (Typical)

quiescent states and can be connected to a

470R
remote relay coil with a resistance of 1KΩ to 5KΩ.

10K
A suppression diode must be connected across + - + - + -
the coil – observe connection polarities. FAILSAFE INPUT
– Output from
If an output is not used install a 4700Ω ½W another panel Options:
3K3/680R or
resistor across its output terminals. 10K/470R
FSI OUT IN OUT IN OUT IN
The Fault Output is normally energised during the FIRE 1 FIRE 2 FAULT
quiescent condition – it will de-energise on any
fault or on total loss of power. Routing Interface

Each associated input circuit is monitored for open

circuit and short circuit conditions using and EOL
resistor (10KΩ).
The primary Fire Routing Circuit is automatically
switched to a failsafe input should the panel suffer
a system fault or total power failure. If required, Typical Arrangement
this input should be connected to and driven by
another fire routing output located on a separate
panel.

2.5.12.2 Fire Protection Routing

The Interface monitors the wiring to and from the
Fire Protection function (i.e. Extinguishing panel).
A separate circuit card (MXP-506) is available to MONITORED
mount in the fire protection equipment to provide INPUT CIRCUIT
(Typical)
the required end of line relays for the output
Input #2

signals and end of line resistors for the return

Input #1

470R

10K

signals.
Input #3
+ - + - + -
Typical functions are shown in the diagram
FAILSAFE INPUT
opposite. The outputs are fully configurable in the – NOT USED
Options:
software. 3K3/680R or
10K/470R
It is possible, for example, to provide two separate FSI OUT IN OUT IN OUT IN

output release circuits where the fire protection

PRE-ALARM
FES FAULT
RELEASED

BLOCKED

equipment requires more than one physical

RELEASE

activation signal.
FAULT

Routing Interface

Typical Arrangement
Refer to Appendix 2 – Recommended Fire Rated Cables for further information on cable types to be
used for these transmission paths.

Page 31 of 72
2.5.13 VdS Interface
PC The is
Mxp-504 is a chassis mount interface
used to connect the panel to dedicated
O N LY
equipment required in Germany and other
markets.
The interface provides input / output circuits for
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
connection to: FAT/FBF FSD ÜE AUSG.S red ÜE

FAT/FBF: Fireman’s Display Terminal /

Fireman’s Control Terminal
FSD: Key Deposit Box
ÜE: Fire Routing Learn Circuit

AUSG.S: Fault Routing

Red ÜE: Fail-safe Fire Routing Input
RS232: Alternative connection to FAT/FBF
Additionally, an Mxp-508 (8-Way Relay Card) can To
be mounted on pillars above the interface to relay
card
provide an additional eight programmable volt-free
relay outputs.
RS232
The circuit card incorporates a button to learn the To
coil impedance connected to the fire and fault base
card
routing circuits.
FSD OPEN and FSD TAMPER inputs can be
configured as monitored or non-monitored
(default). If set to monitored, EOL = 10KΩ, Active Typical Arrangement
Resistance = 470Ω.
# IN/OUT FUNCTION COMMENTS

1 OUT FAT DC POWER +24V

24V DC, 0.5A, Power limited
2 OUT FAT DC POWER 0V

3 IN/OUT RS485 A
Serial Communications
4 IN/OUT RS485 B

5 OUT FSD DC POWER +24V

24V DC, 0.5A, Power limited
6 OUT FSD DC POWER 0V

7 OUT FSD FIRE Open collector output

8 OUT FSD ACK Open collector output

9 IN FSD OPEN Open collector / volt-free input

10 IN FSD TAMPER Open collector / volt-free input

11 OUT ÜE POWER +24V

24V DC, 0.2A, Power limited
12 OUT ÜE POWER 0V

13 OUT ÜE 24V Coil impedance 200Ω-5000Ω

14 IN ÜE ACK Volt-free input

15 OUT FAULT ROUTING +VE

24V Coil impedance 200Ω-5000Ω
16 OUT FAULT ROUTING OV

17 IN FAIL-SAFE ÜE +VE From another VdS interface or from an Mxp-532 Routing

Interface ÜE output.
18 IN FAIL-SAFE ÜE -VE

Page 32 of 72
2.5.13.1 FAT / FBF Direct Connection
The interface is compatible with IFAM FAT3000 and FBF2003 products using IHD protocol.
Both the FAT and FBF can be directly connected to the interface card. When the FAT and FBF are
closely coupled or included in a common housing, connect the FBF via the RS232 connections to
the FAT.
RS485 Connection RS232 Connection
Note: Units connected via RS232 must be wired
in rigid conduit and located ≤ 3 metres from the
panel.
Connect 150R EOL across RXD+/RXD- at FAT RS232
GND
FAT RXD–
FAT TXD+
RS485
RXD+ RXD+
UB1– UB1–
UB1+ UB1+

1 2 3 4 1 2 3 4 21 20 19
FAT/FBF FAT/FBF RS232

Connect 150R EOL across RXD+/RXD- at FBF RS232

GND
FBF RXD–
FBF TXD+
RS485
RXD+ RXD+
–V (27) –V (27)
+V (26) +V (26)

1 2 3 4 1 2 3 4 21 20 19
FAT/FBF FAT/FBF RS232

Connection of an FBF via an FAT

FBF FAT SIO1–

+V (26) AUSG+ SIO1+
–V (27) AUSG– UB1–
TXD+ TXD UB1+
RXD+ RXD
GND GND
RS232

1 2 3 4
FAT/FBF

Page 33 of 72
2.5.13.2 FAT / FBF Redundant Connection
Where several FAT terminals need to be connected, or where a redundant connection is required
from several control panels, connect the FAT units via a redundant ring. This requires the
installation of an IFAM ADP-N3E Interface in one panel and (optionally) an IFAM ADP-N3S Interface
in a second panel if required.
See Section 2.4.5.2 for information on mounting options.
Redundant ring adaptors are built into the FAT terminals as standard.
FBF1 FAT1 FAT2 FAT3 Both power (24V
+V (26)
–V (27)
AUSG+
AUSG–
DC) and data
TXD TXD communications are
RXD RXD
GND
RS232
GND distributed around
the ring.

SIO1+
SIO1–
SIO2+
SIO2–
SIO1+
SIO1–
SIO1+

SIO2+
SIO1–

SIO2–
SIO2+
SIO2–

UB1+
UB1–
UB2+
UB2–
UB1+
UB1–
UB1+

UB2+
UB1–

UB2–
UB2+
UB2–
SIO1+
SIO1–

SIO2+
SIO2–

SIO1+
SIO1–

SIO2+
SIO2–
UB1+
UB1–

UB2+
UB2–

UB1+
UB1–

UB2+
UB2–
ADP-N3E ADP-N3S
RX

RX
TX

TX
0V

0V
PANEL 1 PANEL n

1 2 3 4 1 2 3 4
RS232 FAT/FBF RS232 FAT/FBF
RX

RX
TX

TX
0V

0V

2.5.13.3 FSD Key Deposit Box Connection

The interface is compatible with IFAM SDA-3000 FSD Adaptor Interface.

SDA-3000
TAMPER 13 Key Deposit Box heating power is to be
OPEN 15
supplied separately.
ACK 9
FIRE 10 Refer to the documentation supplied with the
0V 8 SDA-3000 for details of the wiring connections
+24V 7
between the interface and the key deposit box
itself.

5 6 7 8 9 10
FSD

Page 34 of 72
2.5.13.4 ÜE Fire Routing
The interface is compatible with routing equipment with a range of coil impedances from 200Ω-
5000Ω. If the ÜE output is not used, fit one of the supplied 4K7 resistors across terminals 12&13.
24VDC Power can be supplied to the routing
Router ACK equipment if required.
FIRE
0V The typical wiring arrangement is shown in the
+24V picture opposite.
Coil: 200-
5000ohm On network installations, the output from
24V DC
another panel can be routed through the fail-
safe input of the main interface card.
Should the main interface card or panel totally
lose power or be in a system fault condition the
fail-safe input is automatically connected to the
11 12 13 14
ÜE ÜE output. The router should be provided with
power from a separate power supply.

Router ACK
FIRE
0V

+24V
Connect the ÜE Output
Coil: 200- 0V on another network
5000ohm node to the Fail-Safe
24V DC Input on the Interface
card connected to the
router.
Connect to a
separate EN54-4
supply

11 12 13 14 15 16 17 18 11 12 13 14
ÜE AUSG.S red ÜE ÜE
Node 1 Node n

2.5.13.5 Fault Routing

The interface is compatible with routing equipment with a range of coil impedances from 200Ω-
5000Ω. If the Fault Routing output is not used, fit one of the supplied 4K7 resistors across terminals
15&16.

Router
–
Coil: 200-
+
5000ohm
24V DC
+24V
0V

Connect to a
separate EN54-4
supply
15 16 17 18
AUSG.S red ÜE

Page 35 of 72
3 Programming
3.1 Introduction
These instructions cover the configuration and programming of the panels.
PC Where you see the “PC Only” symbol, these features can either only be set-up using the
ONLY PC Configuration Tool or there are additional options that are only available via the PC
Configuration Tool.

3.1.1 Access Levels

The panel operation is protected from inadvertent and erroneous misuse by means of four access
levels. These levels are as follows:

Level 1 Untrained user

Level 2 Authorised User
Level 3 Commissioning, Service and Maintenance
Level 4 Commissioning, Service and Maintenance – Special Tools Required

This document covers the Level 3 functions. For details on the operation and use of the panel at
Levels 1 & 2, refer to User Manual 680-166. Full details are supplied with the special tools.

A level-3 password is required to enter the commissioning menus. For details of Passwords, refer to
Section 3.3.13.

Level-3 Passwords.
Default
If this number is lost, it is not possible to enter commission mode functions.
7654
Refer to section 5.1 for further formation.

3.1.2 Memory Lock

The configuration memory may be protected
against inadvertent change by means of a
memory lock.
Before making any configuration data changes,
move the jumper strap to the OPEN position.
After all changes have been made, move the
jumper strap back to the CLOSE position to
protect the memory against inadvertent change.
Refer to the diagram opposite for information on Typical View – Unlocked
the jumper settings.

3.1.3 Navigating through menus

The display will revert to status mode after 60s. Press the ‘Menu’ button to restore the display.

[Commission Menu 1]

LOOPS ZONES EXIT

VIEW DISABLE ENABLE
Next Menu

When a menu is displayed, use the ÍÏÐÎ buttons to highlight the required menu option and then
press the  button to select it.

Press the ‘Esc’ button from within a menu option to return to the previous menu.
The display can be forced back into status mode by pressing the ‘Esc’ button when at the top level
commissioning menu (or by waiting 60s).
Page 36 of 72
3.1.4 Changing Text Descriptions
Various parameters can have a text description defined. These include loop devices, zones, etc.
The zone and device text descriptions will be shown on the display in the Fire Alarm, Fault and
Warning Conditions, etc. to provide a quick and clear indication of the source of the problem.

To change the text description, first highlight the text description within the appropriate programming
option and then press the  button. The display then changes to show the text entry dialogue
screen. For example:

>RESTAURANT <

KEY IN THE REQUIRED TEXT 1 2abc 3 def

4 ghi 5 jkl 6 mno

7pqrs 8 tuv 9wxyz

The method of entering the characters is similar to the method employed
on mobile telephones. The number buttons provide both their appropriate Esc 09 Menu
number and several letters of the alphabet. An example of the keypad is
shown opposite.
For example, Button 2 allows entry of the number 2 and letters A, B and C.
When a button is pressed, the first character is shown on the display at the current cursor position. If
the button is pressed again within ½ second, the second character replaces the first. A further press
displays the third available character and so on – see table below. After pressing the button to
obtain the required character, wait for 1-second and the character will be entered and the cursor will
move to the next character in the text description.
Pressing another button will immediately enter the previous character and move the cursor on to the
next character.
Use the ÍÎ buttons to move backwards or forwards along the line. When the text description is as
required, press the  button to confirm the change.
If the text has been entered incorrectly, press the ‘Esc’ button to cancel all changes and return to
the previous display.
The following table shows the numbers, characters and symbols assigned to each button on the
keypad.
st nd rd th th
Button 1 Press 2 Press 3 Press 4 Press 5 Press Further Characters

1 1
2 A B C 2 Ä, Æ, Å, À, Á, Â, Ã, Ç
3 D E F 3 È, É, Ê, Ë, Đ
4 G H I 4 Ì, Í, Î, Ï
5 J K L 5
6 M N O 6 Ö, Ø, Ò, Ó, Ô, Õ, Ñ
7 P Q R S 7
8 T U V 8 Ù, Ú, Û, Ü
9 W X Y Z 9 Ý, Þ
0 Blank 0

Alternatively, press the ÏÐ buttons to scroll through a list of characters. When the required
character is shown, press the Î button to move on to the next character. The list of characters
available and the order of presentation is as follows:

Blank !“#$%&‘()*+,-./ 0123456789 :;Ù?@ ABCDEFGHIJKLMNOPQRSTUVWXYZ [‘]^_

Page 37 of 72
3.1.5 Numeric data entry
Numbers are entered by moving to the required field, and then typing in the required number,
followed by the  button.

If the number is entered incorrectly, press the ‘Esc’ button to restore the previous number.

3.2 Level 3 Menu Functions

The following table gives a list of the Level 3 Menu Functions, the sub-functions available within
each main function and a brief description for each function. The menu options are available on
three pages – select “Next Menu” to switch between pages.

Main Menu Option Sub Menus Comments

3 LOOPS View/Edit View, test and configure the loop devices. P
4 A
Auto Learn Learn the Devices Present on the Loop.
G
Calibrate Calibrates devices on the loop. E
History View historic information (last activation, last test, etc.) of each device. 1
Meter View information on the driver circuit performance.
6
Scope View oscilloscope of driver circuit performance
6 ZONES -- Configure the Zone texts.
EXIT -- Cancel Level 3 Access and return to Level 2 Menu Options.
7
DISABLE Disable Zones/inputs, Outputs and Groups.
7
ENABLE Enable Zones/Inputs, Outputs and Groups.
VIEW Fires View Zones and Inputs that are reporting a fire alarm condition.
Faults View Zones and Inputs that are reporting a fault condition.
Alarms View Zones and Inputs that are reporting an alarm condition during test.
Disabled View Zones, Inputs and Outputs that are disabled.
Inputs View the current state of Zones and Inputs.
Outputs View the current operational condition of all output circuits.
Log View the Event Log.
Panel View the software of all installed components and the operational state,
voltage & current loading of the panel I/O hardware.
Network View Network Diagnostics.
Warnings View Zones and Inputs that are reporting a warning condition
Supervisory View Zones and Inputs that are reporting a supervisory condition
2 PASSWORDS -- Configure the Level 2 and Level 3 passwords. P
A
TIME/DATE -- Change the Date and Time Settings.
G
PC-CONFIG -- Enable the PC Link for transfer of configuration data to and from the panel. E
EN54-13 -- Configure the Operating Characteristics of the Output Circuits. 2
1 SETUP -- Configure General Operating Parameters.
DISPLAY -- Adjust the display contrast setting

PANEL -- View and configure all panel internal circuits. P

A
5 OUTPUT-GROUPS -- Configure Output Group Cause and Effect Programming.
G
7
TEST Test Zones, Display, Buzzer, Printer and Outputs. E
3

6
Refer to separate application note on this function
7
The operation of these menu functions are not described in this manual – refer to the User Manual for further information.

Page 38 of 72
3.3 Recommended Programming Procedure
The main programming steps required will necessarily be different for each installation. However,
the following is the minimum recommended.
♦ Step 1 – SET-UP, Define General Set-up Information (Phone Numbers, etc.).
♦ Step 2 – PASSWORDS, Define Level 2 and Level 3 Passwords as required.
♦ Step 3 – AUTO-LEARN, Let the panel learn the devices on the loop(s).
♦ Step 4 – VIEW DEVICES, Enter Zone Numbers, Location text and Change Group Assignments
if required.
♦ Step 5 – OUTPUTS, Program Output Groups as required.
♦ Step 6 – ZONES, Enter Zone Texts as required.

3.3.1 Loops
For Multi-loop panels only – On selecting the LOOPS option, the display will prompt for the loop to
be viewed / programmed. For example: -
[Select Loop]

1st-Loop 2nd-Loop 3rd-Loop 4th-Loop

9 9 x x

The list of loops available will be adjusted automatically to show only those loops that are available
or have a loop driver card installed. In the above example, loop drivers are installed in positions 1
and 2 of an Mx-5400.
Press the ÏÐÍÎ buttons to scroll through the list of loops available and then press the  button
to select the loop required.
Note: For the Mx-5100, and as there is only one possible circuit, the display will immediately show a
list of programming options as follows:
[Loop 1]

VIEW/EDIT AUTO LEARN CALIBRATE

HISTORY METER SCOPE

3.3.2 Loops – View/Edit

The VIEW/EDIT option shows a list of the devices connected to the loop learnt by the panel. For
example:
[Loop 1] More>
Address State Type Value
001.0 Normal CALL POINT 16
002.0 Normal MULTI.SENSOR 28
003.0 Normal ION SMOKE 23
004.0 Normal HEAT 21

The first device on the loop is shown at the top of the list and is highlighted. Press the ÏÐ buttons
to scroll through the list of devices.
Press the ÍÎ buttons to view additional information. The display highlights a particular parameter.
To change the value of this parameter (if not view only), press the  button and appropriate options
will be shown on the display. The address field is always shown for reference.

Page 39 of 72
3.3.2.1 State
This parameter shows the current operational status of the device. For example, this can show
Normal, Fire Alarm, Device Missing, etc.
This parameter cannot be changed.
3.3.2.2 Type
This parameter shows the type of device learnt by the panel. For example, this can show Call Point,
Multi-Sensor, ION Smoke, Heat, etc.
This parameter cannot be changed.
3.3.2.3 Value
This parameter shows the analogue value returned by the device. The number displayed will vary
according to the type of device fitted. An ‘H’ (High) and ‘L’ (Low) is shown for logic inputs. This
parameter cannot be changed. For specific device types, the mode of operation / sensitivity band is
also shown.
3.3.2.4 Zone
This parameter shows the Zone to which this device has been assigned. Use the number keys to
change the zone assigned to the device. Zones used must be unique to this panel.
3.3.2.5 Meldergruppe Number (Mld)
The Meldergruppe number is only shown on panels for the German market. This is the assigned
device number within the meldergruppe and can be in the range 1 – 32. Use the number keys to
change the meldergruppe number assigned to the device.
3.3.2.6 Device Text
This parameter shows the 26-character location text assigned to this device. For guidance on how
to change the text, refer to Section 3.1.4.
3.3.2.7 Action
This parameter shows the action that will be performed when this device indicates an active (alarm)
condition. For example:
[Loop 1 Devices] <More>
Address Action Sensitivity O/P
001.0 FIRE SIGNAL DEFAULT
002.0 FIRE SIGNAL DEFAULT
003.0 FIRE SIGNAL DEFAULT
004.0 FIRE SIGNAL DEFAULT

Press the  button to change the action assigned to this input device. A pop-up window is then
shown on the display from which an action can be selected.

[Select New Action]

FIRE SIGNAL .
PRE-ALARM
FAULT SIGNAL

Press the ÏÐ buttons to scroll through the list of Actions and then press the  button to confirm the
change. The display reverts to the device list showing the new action assigned to this device.
Alternatively, press the ‘Esc’ button to cancel the changes and return to the device list display. The
following Actions are available.

Page 40 of 72
Action Description
8
Fire Signal A Fire Alarm Condition will be generated whenever the input is active.
Pre-Alarm A Pre-Alarm Condition will be generated whenever the input is active.
Supervisory A Supervisory Condition will be generated whenever the input is active
Create Alarm 1 An “Alarm 1” condition will be generated whenever this input is active.
Control Signal Allows control of Outputs without displaying “Fault” or “Fire” or sounding buzzer
Fault Signal A Fault Condition will be generated whenever the input is active.
Key Lock Enables / Inhibits front panel controls (Disable, Mute, Reset etc.)
Acknowledge Activation of the input acknowledges a Stage 1 Investigation Delay and invokes the Stage 2 Timer
Security A Security Alert Condition will be generated whenever the input is active.
- No Action is assigned to the input.
9
LED Test Activation invokes a test of the panel LED Indicators.

PC
ONLY Additional actions are available via the PC Tool.

3.3.2.8 Sensitivity
Refer to the appropriate protocol application note for further information.
This parameter shows if the device sensitivity is set to its “DEFAULT” or “CUSTOM” settings. For
example:
[Loop 1 Devices] <More>
Address Sensitivity
001.0 DEFAULT
002.0 DEFAULT
003.0 CUSTOM
004.0 DEFAULT

Press the  button to change the sensitivity assigned to an input device. When selected a new
screen displays the sensitivity settings assigned. For example, with an Apollo Discovery device:
SENSITIVITY ADJUST MODE (ION SMOKE )

[ Alarm = 55 ]
[ Mode = 3 ][ Pre-Alarm= 45 ]
[ Delay = 5s][ Min.Value= 8 ]
[SAM/SSM]

Press the ÍÏÐÎ buttons to highlight the required menu option and then press the  button to
select it. Use the number buttons to enter the required value. Alternatively, press the ‘Esc’ button to
cancel the changes.
The alarm thresholds and delay times can be unique for every device if required.

Always ensure that the values chosen are suitable for the particular installation and that reliable
fire coverage is maintained at all times.

8
Fire Alarm Conditions are latched. By default, all other conditions are non-latching. The action for smoke and certain other
detectors is always fire and cannot be changed.
9
LED Test can only be configured using the PC Tool.
Page 41 of 72
3.3.2.8.1 Mode:
This option is shown on the display for specific device types only. Refer to the appropriate protocol
application note for further information.

3.3.2.8.2 Delay
The value in this field defines the delay from detecting an alarm to entering the alarm condition. The
delay time can be changed in 1-second increments.

3.3.2.8.3 Alarm Level

The Alarm Level is the level of the analogue value returned by the detector at which the panel will
enter a Fire Alarm Condition. Refer to the appropriate protocol application note for further
information.

3.3.2.8.4 Pre-Alarm
The Pre-Alarm Level is the level of the analogue value returned by the detector at which the panel
will enter a pre-alarm condition.

3.3.2.8.5 Minimum Value

If the detector analogue output falls below the minimum value programmed, the panel will enter a
fault warning condition. Refer to the appropriate protocol application note for further information.

3.3.2.8.6 Special Sensitivity Mode SSM/Clock

In addition to the “SENSITIVITY ADJUST MODE”, a device can also run in a “SPECIAL
SENSITIVITY MODE” (SSM) under time-clock control.
All panels supports 10 independent, 7-day time clocks.
With the SAM/SSM Option highlighted, press the  button to view the Special Sensitivity Mode
settings. For example:
SPECIAL SENSITIVITY MODE (MULTI.SENSOR)

[SSM/Clock = 2 ][ Alarm = 55 ]
[ Mode = 5 ][ Pre-Alarm= 40 ]
[ Delay = 5s][ Min.Value= 8 ]
[SAM/SSM]

In the above example the panel is using special sensitivity mode 5 (and time clock number 2). Enter
“0” in the SSM/Clock field to cancel Special Sensitivity Mode.
A number must be entered in the SSM/Clock field to select the appropriate SSM number and time
clock. To view the time clock settings, highlight the SSM/Clock field, and press the  button.
For example:
[Time Clock 2]
DAY ON -> OFF ON -> OFF
MON 00:00 00:00 19:00 00:00
TUE 00:00 06:30 00:00 00:00
WED 00:00 00:00 00:00 00:00
THU 00:00 00:00 00:00 00:00

The panel supports two independent times for each day of the week during which the SSM mode
will be switched on (i.e. during which the Special Sensitivity Mode settings are active)
In the above example the SSM will be active between 19:00 on Monday and 06:30 on Tuesday.
Press the ÍÏÐÎ buttons to select the appropriate time field and use the number buttons to enter
the required times. Press the ‘Esc’ button to return to the previous menu display.
Every type of device (the device type is shown in the top, right hand corner) supports unique SSM
settings for each SSM/Clock number. In the previous example the Special Sensitivity Mode settings
have been defined for a Multi-Sensor that is using SSM/Clock number 2. If other Multi-sensors on
Page 42 of 72
the same panel also require the same settings, then you only need to set them to SSM/Clock 2. If
instead another Multi-Sensor requires a different setting, use a different SSM/Clock number.
3.3.2.9 O/P Group
The Output Group assigned to the Sounder or Relay Devices determines the manner in which the
outputs will operate when a fire alarm or other programmed condition occurs.
For example:
[Loop 1 Devices] <More>
Address O/P Group
020.0 199
021.0 199
022.0 199
023.0 199

Use the number buttons to change the value of the O/P Group setting.
By default, all Loop Output devices are assigned to Output Group 199.
For detailed information and guidance on the programming and use of Output Groups, refer to
Section 5.4
3.3.2.10 Additional Info
This parameter shows additional information, if available, for this device. For example, the following
display shows the Apollo detector series types:
[Loop 1 Devices] <More>
Address Additional Info
001.0 Disco
002.0 XP95
003.0 Disco
004.0 Disco

Refer to the appropriate protocol application note for further information.

3.3.2.11 Device Testing
Individual detectors can be tested to check the chamber response and illuminate the detector LED
and individual outputs (sounders and relays) can be tested to check output connections and
operation.
While the address field is highlighted, press the ÏÐ buttons to scroll through the list of devices to
the desired device (or key in the address, and then press the  button).
[Loop 1 Devices] <More>
Address State Type Value
005.1 Normal SOUNDER -
006.0 Normal MULTI.SENSOR 16
006.1 Normal RELAY -
007.0 Normal CALL POINT 16

A menu will appear to confirm that you want to “Test This Device”.
Press the  button to confirm or press the ‘Esc’ button to cancel.
Once selected, commands are sent to the detector to turn on the detector LED and put the chamber
into test or are sent to the output device to turn the output on. The “Test” LED lights up and the
panel display returns to the list of devices.
A few seconds after a detector is placed into test, the analogue signal will be seen to rise. If the
detector is then left in the test condition, the Detector State will change to a “Fire Test” status.
The test is cancelled as soon as the display is scrolled up or down or when the ‘View Devices’
option is exited.

Page 43 of 72
3.3.3 Loops – Auto Learn
3.3.3.1 Normal Procedure / Initial learn
The panel can automatically learn the presence or absence of devices at all addresses connected to
the loop. When the Auto Learn option is selected, the panel starts searching each address on the
loop to locate and find all of the devices connected. A display is shown to indicate the progress of
this procedure.
For example:
[Auto Learn Loop 1] HOCHIKI

Address 15 Devices found = 3

When all addresses have been searched, the panel displays a summary screen showing the
quantity of devices found for each type of device.
For example:
[Auto Learn Loop 1] HOCHIKI

Address 127 Devices found = 4

OPT ION MUL TMP MCP SCC I/O ZMU OTHERS
0 1 1 1 1 0 0 0 0

This summary provides a quick check to ensure that the panel has found all of the devices that
should be connected to the loop.
Press the ‘Esc’ button to return to the main Loops Menu.
3.3.3.2 Procedure if the Panel finds Devices Missing
When the panel cannot communicate with a device previously programmed into the panel, the Auto
Learn process is suspended and the display shows a pop-up window with options. For example:

KEEP THIS DEVICE .

DELETE THIS DEVICE
KEEP ALL MISSING
DELETE ALL MISSING
! Address 002 DEVICE MISSING

If the missing device is kept (or all missing devices are kept), the panel remembers the
programming for these devices. The panel will report a fault condition until such time as the missing
devices are reconnected.
If the missing device is deleted (or all missing devices are deleted), the panel clears all previous
programming for these devices. This includes any sensitivity threshold changes, text assignments,
zone assignment, action, etc.
Press the ÏÐ buttons to highlight the required menu option and then press the  button to confirm.
The pop-up window will disappear and the panel will continue with the auto learn process.
If a single device is deleted and another missing device is subsequently registered, the display will
once again show the pop-up window to keep or delete this device.
3.3.3.3 Procedure if the Panel finds Devices Added
When the panel finds a device not previously learnt and programmed in the panel, the Auto Learn
process is suspended and the display shows a pop-up window with options. For example:

Page 44 of 72
 ACCEPT NEW DEVICE .
REJECT NEW DEVICE
ACCEPT ALL NEW DEVICES
REJECT ALL NEW DEVICES
! Address 002 NEW DEVICE

If the new device is accepted (or all new devices are accepted), the panel will configure the memory
to register these devices. All data will be configured to initial settings for sensitivity threshold
changes, text assignments, zone assignment, action, etc. for these devices.
If the new device is rejected (or all new devices are rejected), the panel clears all programming for
these devices and will not attempt to communicate with the devices at these addresses.
Press the ÏÐ buttons to highlight the required menu option and then press the  button to confirm.
The pop-up window will disappear and the panel will continue with the auto learn process.
If a single device is accepted / rejected and another new device is subsequently registered, the
display will once again show the pop-up window to accept or reject this device.
3.3.3.4 Procedure if the Panel finds Devices Changed
When the panel finds a new type of device installed at an address previously learnt and
programmed in the panel, the Auto Learn process is suspended and the display shows a pop-up
window with options. For example:

ACCEPT NEW DEVICE .

KEEP OLD DEVICE
ACCEPT ALL NEW DEVICES
REJECT ALL NEW DEVICES
! Address 002 TYPE CHANGE

This situation could arise for example if a heat detector has been installed in place of an optical
smoke detector.
If the new device type is accepted (or all new device types are accepted), the panel will configure
the memory to register these devices. All data will be configured to initial settings for sensitivity
threshold changes, text assignments, zone assignment, action, etc. for these devices.
If the new device type is rejected (or all new device types are rejected), the panel remembers the
programming for the original devices. The panel will report a fault condition until such time as the
correct device types are reconnected.
Press the ÏÐ buttons to highlight the required menu option and then press the  button to confirm.
The pop-up window will disappear and the panel will continue with the auto learn process.
If a single device is accepted / rejected and another new device type is subsequently registered, the
display will once again show the pop-up window to accept or reject this device.

3.3.4 Loop – Calibrate

Calibrates Hochiki devices – Note this can take up to several minutes if many detectors & sounder
bases are installed.

3.3.5 Loop - History

Displays basic event history for each device and sub-address.
[History Lp 1 Adrs 001.0 ↓ ]
Last Activation :
Last Test :
Last Disable :
Last Enable :
Created : 12/01/09 09:18:58

Page 45 of 72
Item Description
Last Activation The date and time that the device was last activated (e.g. smoke level detected
is at pre-alarm or alarm levels or the last time that an output was turned on).
Last Test The date and time that the device was last tested (e.g. smoke level detected is
at pre-alarm or alarm levels or the last time that an output was turned on).
Last Disable The date and time that the device was last disabled.
Last Enable The date and time that the device was last re-enabled.
Created The date and time that the device was either auto-learnt at the panel or added
to the device list from a PC configuration.

3.3.6 Loop – Meter

Displays loop output and input voltages and loop loading.
A diagnostic display with automatic scanning of the loop to find devices with minimum and maximum
communication pulse heights is available.

3.3.7 Loop – Scope

This function displays the loop input and output voltage and current measurements in the form of a
waveform. Refer to separate application note for details of this feature.

Page 46 of 72
3.3.8 Zones
The Commission Zones option lists all the zones in use by this panel and allows the zone text
description to be changed.
[Commission Zones]
Zone Location
0001 BASEMENT WEST
0002 RECEPTION
0015 EAST WING
0018 TOWER BLOCK

To change the location text assigned to the Zone, press the  button when the Zone Location Text
is highlighted. Refer to Section 3.1.4 for guidance on how to change text descriptions.
To select a different zone, use either the scroll up/down keys, or just type in the number of the
required zone, followed by the  button. Note that only zones in use are displayed.

3.3.9 Exit
To exit the Commission Mode and return the panel to normal operation (i.e. level 2), select the “Exit”
option. The display will prompt for confirmation of the Level 3 password. For example:
[Commission Menu 1]
Please Enter Your Password

Next Menu

If the password is incorrect (this will be indicated) or if the password is not entered within 5-seconds,
the display will revert to the Commission Level Menu and level-2 will not be entered.
After commissioning, the panel must always be returned to level 2 (or level 1) to give normal fire
coverage.

3.3.10 Disable
This function is the same as User Level 2 function – refer to User Manual for further information.
The following options can be disabled:
♦ Zones / Inputs
♦ Outputs
♦ Groups

If beacon outputs are configured so that they can be independently disabled /

PC enabled, then configure one of the front panel “Function” LED indicators to
ONLY indicate the disabled state of these devices.

3.3.11 Enable
This function is the same as User Level 2 function – refer to User Manual for further information.
The following options can be disabled:
♦ Zones / Inputs
♦ Outputs
♦ Groups

Page 47 of 72
3.3.12 View Options
The View Menu Options are identical to those available during Level-2 operation – refer to User
Manual for further information.

3.3.13 Passwords
The panel provides up to 10 User Level-2 passwords and 2 Level-3 passwords. All of the passwords
10
can be changed.
On entry to the function, the display shows a list of the passwords. For example:
Password Access level User ID
15633 2 01
9988 2 02
13344 2 03
10000 2 04
10000 2 05

To change a password, use the ÏÐ buttons to highlight the required password and then enter the
new password using the number buttons. When the password is correct, press the  button to
confirm.
Level-3 Passwords.
Care should be taken when changing the Level-3 password. If this new number is lost, it is not
possible to enter commission mode functions.
Refer to 5.1 for further information.

The factory default level 3 password is 7654

3.3.14 Time and Date

This function allows the time and date in the panel to be changed. On entry to the function, the
display shows the current time and date with confirmation of the day of the week on the bottom line.
For example:
[SET TIME/DATE]

TIME = 15:28
DATE = 15/01/09 THU 15 JAN 2009

To change the settings, use the ÏÐ buttons to highlight the required option. Directly enter the new
time or date using the number buttons. As soon as a number button is pressed, the display will
clear the current setting and show the new value as it is entered. For example:
[SET TIME/DATE]

TIME = 1-:--
DATE = 15/01/09 THU 15 JAN 2009

3.3.15 PC Config
The PC Link Option enables the connection of the PC Configuration Tool for retrieving configuration
data from the panel and programming configuration data from a file on the PC.
For further information, refer to the Manual supplied with the PC Configuration Tool.

10
The passwords can be further qualified using the PC CONFIG TOOL to provide permission / restriction to specific menu
options. See User Manual 680-166 and PC CONFIG TOOL Manual for further details.
Page 48 of 72
3.3.16 EN54-13
The EN54-13 menu defines whether EN54-13 transmission path monitoring is in use and defines
the actual load current (shown in milliamps) to be used in the calculation for each of the base card
loop and sounder circuits.
If enabled, the panel monitors the circuits to ensure that at the specified load current, the circuit can
deliver the load current whilst still maintaining circuit device voltage compatibility levels via the
transmission path resistance.
[EN54-13 Setup]

In Use : 
Loop Circuit 1 : 500
Loop Circuit 2 : 500
Loop Circuit 3 : 500

Use the ÏÐ buttons to scroll through the list of options.

Press the  button to select between “in use” and “not in use” 11.
Use the number keys to enter / change the load current for each circuit. The default values are the
circuit maximum.
Circuit I minimum I maximum EOL Voltage
Loop Circuit 0mA 500mA 17V
Sounder Circuit 0mA 1000mA 16V

The actual load for each circuit in alarm can be viewed using the View Panel option (see 3.3.12 and
user manual).

3.3.17 Setup
The Setup Options Menu enables the configuration of panel generic operating parameters. When
the option is selected, the display shows a list of the available parameters. For example:
[Setup]

THIS NETWORK NODE : . 0 .

NEXT NETWORK NODE : 0
PANEL ZONE : 100
SERVICE NUMBER : 01234 567890

Use the ÏÐ buttons to scroll through the list of options. The following will then be shown:
[Setup]

SERVICE DUE DATE : 01 JAN 2011 10:00

TRACE LOGGING MODE : STANDARD More>
DETECTOR BLINKING : NONE
COMPANY LCD LOGO : 

3.3.17.1 Network
This Network node is set to 0 for a standard non-networked panel. For panels in a networked
application please refer to the Network document, reference: 680-502.

11
When “Not In Use” is selected, the panel will still continue to monitor the circuits for open circuit and short circuit conditions.
Loop circuits are monitored via the return voltage on the loop. Sounder circuits must be terminated using the standard EOL
resistors.
Page 49 of 72
3.3.17.2 Panel Zone
By default all the panel inputs are assigned to the Panel Zone. Alternatively the PC configuration
program allows individual inputs to have different zones if required.
3.3.17.3 Service Number
The Service Number is the telephone number that is shown on the status display whenever a fault
condition is accepted. To change the number, press the  button when the option is highlighted.
The number is entered using the text entry facility; refer to Section 3.1.4 for guidance on how to
enter text.
3.3.17.4 Service Due Date
The next service (over) due date can be entered into the panel memory. When this date is reached,
the panel will enter a fault condition to alert the site operator that a service visit is overdue. To
change the due date, press the  button when the option is highlighted. The display prompts for
entry of the next service date. For example:

[NEXT SERVICE DUE]

TIME = 12:00
DATE = 24/04/12

Use the ÏÐ buttons to select between the time and date. Use the number buttons to enter the
required time or date.
As soon as a new service date is entered, the panel will cancel any Service Due Fault condition.
3.3.17.5 Trace Logging Mode
The Trace Logging Option determines what type of information and to what level is stored in the
Event Log.
There are three options:
STANDARD = the normal operating mode logging fire alarm, fault and warning conditions as
they occur.
STANDARD + = an extended version of the standard operating mode where the removal of fault
and warning conditions are also logged.
DIAGNOSTIC = a full diagnostic trace of all conditions with greater depth to aid diagnosis of fault
conditions.
To change the option, press the  button.
To erase the event log, press the Î button to view the additional command option as follows:
[Setup]

TRACE LOGGING MODE : Wipe Event Log

DETECTOR BLINKING :
COMPANY LCD LOGO :
PROGRAM ID :

Press the  button and the display will show that the event log is being erased by display the
message “WORKING…” After the event log is erased, the display reverts to the Set-up Options
screen.
3.3.17.6 Detector Blinking
The Detector Blinking option determines whether the LED indicators on the devices will blink
whenever the panel polls the device. To change the operation, press the  button. The display
presents a list of options. For example:

Page 50 of 72
 [Setup]
INDIVIDUAL
ALL
NONE

Use the ÏÐ buttons to scroll through the list of options and press the  button to confirm the
selection.
The device LED indicators will not blink if NONE is chosen or will blink if ALL is chosen. Note that
only certain devices, such as Apollo Discovery, support this feature.
If a device, such as a Discovery device, is changed it may be necessary to select and reconfirm the
blinking command so that the new device will blink its LED.
The INDIVIDUAL option should be chosen when it is required that only certain devices should blink
their LED. The devices that shall blink their LED can only be programmed using the PC
Configuration Tool.
3.3.17.7 Earth Fault Notification
This parameter determines whether an Earth Fault is shown on the display during normal operation.
To change the setting, press the  button. The status changes from  to X and vice versa.
3.3.17.8 Resound
The Resound option defines whether silenced sounders shall resound when either a new zone is in
alarm (default EN54-2 setting) or a new device is in alarm.
3.3.17.9 Config Data
The Config Data option shows the loop protocol selected and the checksum for the configuration
data. A note of this number can be taken and then checked on the next service visit to see if any
changes have been made to the configuration data.
[Setup]

CONFIG DATA :APOLLO More>

To change the protocol, press the  button. A pop up window is shown with the following options

. KEEP PROTOCOL .
! CHANGE LOOP PROTOCOL !

Use the ÏÐ buttons to select the required options and press the  button to confirm the selection.
Selecting “CHANGE LOOP PROTOCOL” will toggle to the alternative loop protocol available (i.e.
Apollo/Hochiki/Vega). For Mx-5000N Series panels the protocol is fixed as NITTAN.
Changing between protocols will automatically erase all loop devices from the
configuration memory.
Perform an “Auto-Learn” or use the PC Config Tool to re-define the devices
connected to the loop.

To view the Config Data Checksum, press the Î button. The display then shows:
[Setup]

CONFIG DATA :CGF= 351677 <More>

Page 51 of 72
In addition, there is an option to erase the Config Data. Press the Î button. The display then
shows:
[Setup]

CONFIG DATA :ERASE CONFIG <More

Press the  button. A pop-up menu will be shown to confirm whether the configuration data shall be
erased.

3.3.18 Display
Depending on the physical mounted height of the panel, the contrast of the LCD may need adjusting
to obtain optimum viewing. The display option permits the contrast adjustment of the LCD.
[DISPLAY OPTIONS]

ADJUST CONTRAST

Press the  button. The following display is shown:

Use the ÏÐ buttons to adjust the contrast viewing angle for darker or lighter as required (the setting
is confirmed by the bar graph) and the press the  button to confirm the change. Press ESC to
cancel. The display will automatically cancel if no button is pressed for 30 seconds (hour glass).

3.3.19 Panel
The Panel Menu Option shows a list of the internal panel circuits and provides a means to change
their default configuration settings.
Only use this menu if changes are to be made to the default settings for the panel’s internal circuits.
Use the VIEW-PANEL Menu Option to view the state and operating condition of each circuit.
The display shows for example:
More>
Address State Type Value
>001.0 Normal VOLTAGE 5.6V
001.1 Normal VOLTAGE 5.6V
002.0 Normal CURRENT 0mA
002.1 Normal CURRENT 0mA

Use the ÏÐ buttons to scroll through the circuits. Use the ÍÎ buttons to view additional
information. The zone and Output Group Assignments can be modified if required.
For further information on the View – Panel Options and the information that is presented, refer to
the User Manual.

Page 52 of 72
3.3.19.1 AC Fail Delay
The panel can be configured to delay the reporting of a loss of AC Mains supply (Address 14.0).
The front panel Green Power LED will still immediately flash on the loss of the AC Supply, but the
fault condition is only reported after the delay time (default 10s) has elapsed.
SENSITIVITY ADJUST MODE (MONITOR )

[ Alarm = *** ]
[ Pre-Alarm= *** ]
[ Delay = 10s][ Min.Value= 372 ]
[SAM/SSM]

To delay the reporting of an AC Supply Loss, change the “Delay” setting12.

12
For compliance with EN54-4, the loss of the AC Mains supply should not be delayed more than 30 minutes (1800s).

Page 53 of 72
3.3.20 Output Groups
The “Cause and Effect” programming is a schedule of actions that will turn on one or more outputs
dependant on a set of input events.
The Outputs Option provides the means to create simple or complex “cause and effect”
programming within the panel. Delays can be introduced to allow a phased evacuation of a building
(Note this is different to an “Investigation Delay” which is detailed in section 3.3.21).
This section describes the settings and options in detail for each parameter. Refer to Appendix 4 –
Cause and Effect Programming Example for a description of how to program a typical requirement.
More complex “Cause and Effect” programming may be undertaken using the PC Configuration tool.

When the OUTPUTS Option is selected, the display shows the cause and effect programming for
Output Group 1. For example:

[Output Group 1] [ 3.9% Mem used]

ZONE CAUSE STYLE=Delay->MODE Wait
1 ANY FIRE 00 - On
2 ANY FIRE 00 - On
3 ANY FIRE 00 - On
4 ANY FIRE 00 - On

To simplify the cause & effect programming, one or more outputs that will respond in the same way
when the same set of input events occurs can be grouped together. This association of outputs is
called an Output Group.
The panel can support up to 200 of these Output Groups.

To select a different Output Group, press the Ï button to highlight the Output Group Number field
and then enter the number of the output group required using the number buttons. The display
always shows the Output Group is shown in the top left corner.
Press the ÏÐ buttons to scroll through the list of zones.
Press theÍÎ buttons to select the fields for a particular zone.
Press the  button to select a particular field option to change its setting.
3.3.20.1 Default Output Settings
On initial installation, or after clearing the configuration memory, all outputs are assigned to specific
Output Groups and will turn on immediately a single fire alarm occurs in any zone (any fault
condition for the fault relay). The default assignments are as follows:

Output Device Output Group Cause and Effect

On-board Sounder A 1 Any fire in any zone – no delay
On-board Sounder B 1 Any fire in any zone – no delay
13
On-board Sounder C 1 Any fire in any zone – no delay
13
On-board Sounder D 1 Any fire in any zone – no delay
14
On-board Relay 1 200 Any fault in any zone – no delay
14
On-board Relay 2 199 Any fire in any zone – no delay
14
On-board Open Collectors 199 Any fire in any zone – no delay
15
Fault Routing Output 200 Any fault in any zone – no delay
15
Fire Routing Output-A 199 Any fire in any zone – no delay
15
Fire Routing Output-B 199 Any fire in any zone – no delay
All Loop Output Devices 199 Any fire in any zone – no delay

13
Mx-5400 Only
14
This Output is used for routing if the non-monitored routing option is selected.
15
This Output is available on the optional Routing Interface Peripheral Card.
Page 54 of 72
3.3.20.2 Cause
Each Output Group can be programmed to respond in a unique way to events from each individual
zone. An input event may be a fire alarm condition or it may be a fault, disablement or other
condition. A combination of criteria may also be applied to each zone.

The Cause field determines what type of input event (or a combination of input events) will generate
an output response for the selected input zone.

[Output Group 1] [ 3.9% Mem used]

ZONE CAUSE STYLE=Delay->MODE Wait
1 ANY FIRE 00 - On
2 ANY FIRE+ 00 - On
3 ANY FIRE 00 - On
4 ANY FIRE 00 - On

Press the  button to change the setting and a pop-up window will appear showing the options
available. For example:

[FIRE ] [D/K FIRE] [ALARM][PRE-ALARM]

 - - -
[FAULT] [I/P DISABLE][TEST ][ CONTROL ]
- - - -

Press theÍÏÐÎ buttons to highlight the required menu option and then press the  to change its
setting. An input action type is enabled when a ‘’ is shown beneath the option. It is permitted to
select multiple input types in which case a combination of input events will result in an output action.
If there is a combination of input events, the CAUSE display above shows this extended
programming by adding a ‘+’ to the text. For example, Zone 2 above shows that the basic event is
ANY FIRE + other criteria.
Press the ‘Esc’ button to return to the previous display.
The definition for each cause is as follows:

Cause Definition
Fire Any single fire.
Double Knock (D/K) Coincidence of 2 or more fire detectors or a single manual call point in the same zone.
Alarm Activation of an input device programmed with an ‘Alarm’ action.
Pre-Alarm A device in a pre-alarm condition.
Fault Any device entering a fault condition.
Input Disabled Whenever an input device is disabled.
Test A 'Walk Test' fire in the zone.
Control A control input in this zone will cause activation.

Type C: Coincidence Detection.

The operation of the Coincidence Detection (Double Knock) feature is on a per zone
basis.
Section 7.12

PC Type B: Confirmation.
ONLY Optional confirmation filters can be configured via the PC Tool on individual devices.

Page 55 of 72
3.3.20.3 Style
The way in which an output turns on in response to a particular input event can be programmed. For
example, an output may turn on immediately, it may turn on after a delay or it may pulse for a set
time and then turn on. This method of operation is called a Style. A style may have up to three
different methods of operation. For example,
DelayÎ Mode, WaitÎ Mode, WaitÎ Mode.
Style 00 is fixed to turn on immediately an input event occurs.
Style 01 is fixed to pulse immediately an input event occurs.
Styles 02 to 20 are programmable.
Press theÎ button to step on to the style field. Change the setting using number entry to select the
required output style. If the style is already programmed elsewhere, the relevant style parameters
are automatically entered into the appropriate fields.

3.3.20.3.1 Delay
The delay field is the time from qualification of the input event to something happening at the output.
The delay time can be set in intervals of 1 second up to a maximum of 250 seconds.
Press theÎ button to step on to the delay field and change the setting using number entry.

3.3.20.3.2 Mode
The mode field defines the method of operation of the output when it is first activated. This can be
ON or PULSE.
Press theÎ button to step on to the delay field and change the setting using the  button.
Note: Pulse settings are by default 1-second ON / 1-second OFF. Other pulse options can be
specified on the PC Tool (such as 2s ON / 3s OFF) – these can be assigned to on-board outputs
only.

3.3.20.3.3 Wait
The wait field is the time from first activation of the output to the next operational condition (mode) of
the output. For example, the output could initially be delayed for 20 seconds and turn on in a pulsing
mode. After a wait of a further 30 seconds it can be programmed to turn on differently such as ON.
The wait time can be set in intervals of 1 second up to a maximum of 250 seconds.
Press theÎ button to step on to the wait field and change the setting using number entry.
3.3.20.4 Copying Output Settings to Multiple Zones
To save time in the entry of similar Output Group Settings for each zone, it is possible to copy
information programmed for a particular zone to subsequent zones.
Press the Í button to highlight the required zone number and then press the  button. The display
shows a pop-up window prompting for the number of the zone to which to copy the information.
Use the number entry to select the required zone number. The Output Group programming for all of
the zones from the currently selected zone to the zone number entered will be programmed with the
same information as the currently selected zone.

3.3.21 Investigation Delays

In addition to the “Cause and Effect” programming described above, the panels also
PC support an “Investigation Delay Mode” which allows time for a building supervisor to
ONLY investigate fire signals before turning outputs on. This mode can only be configured from
the PC software.

There are two parts to this delay. The first stage is set relatively short. If the building supervisor does
not acknowledge the fire signal within the first stage, the delayed outputs will turn on. The second
stage gives a longer period to investigate the fire signal. This delay can be cancelled at any time by
pressing the EVACUATE button, or any nominated input devices (by default, all call points cancel
this mode).
Page 56 of 72
Each input and output device can be individually programmed to use the investigation delay from
the PC configuration software, together with the times appropriate to each stage of the delay. The
user manual gives details of how the building occupier can turn the investigation delay feature on or
off.

Delays to Outputs.

It must be possible to override the operation of any delays at Level 1. Refer to Section
3.3.21.1 for information on overriding delays.
Section 7.11
For compliance, the maximum total delay permitted is 10 minutes.

3.3.21.1 Overriding Delays at Level 1

A facility to override any programmed delays and immediately activate the sounder circuits should
be provided at Level 1. It is possible to override the delay using the panel controls (see the user
manual for details). This can also be achieved from an input device (such as a manual call point)
that is programmed to turn on all outputs immediately.

3.3.22 Test
This function is the same as User Level 2 function – refer to User Manual for further information.
The following functions can be tested:
♦ Zones / Inputs
♦ Display
♦ Buzzer
♦ Printer
♦ Outputs

3.3.23 LED Indications

This option is not provided from Software Version 050-04.
The operation of all MXP-513-XXX LED Indicator Cards MUST be configured using the PC Tool.
Panels equipped with integral panel LED indicators on the display card will default to indicate fire
alarms in Zones 1-20. The operation of these can be adjusted using the PC Tool.

PC Each LED can be individually configured via the PC Tool to either zone assignment, output
ONLY group assignment or other function.

Page 57 of 72
4 Service and Maintenance
4.1 Maintenance Schedule
This equipment should be maintained in accordance with the regulations and codes appropriate to
the country and location of installation. The following is recommended if no other regulations apply.

4.1.1 Daily Actions

The site operator / user should perform the following checks and actions:
a) The panel indicates normal operation. If any faults exist, these should be recorded in a logbook.
b) Any recorded faults have received attention and have been signed off.

4.1.2 Monthly Actions

The site operator / user should perform the following checks and actions:
a) Any stand-by generators should be started and fuel levels checked.
b) Operate at least one call point or detector (from different zones each month) and check that the
panel enters a fire alarm condition and that the appropriate / programmed alarm or warning
devices are sounded / operated. Where permissible, this should include any links to the fire
brigade or remote centre.
c) Check that all outstanding faults have been recorded and have received attention.

4.1.3 Quarterly Actions

The service / maintenance contractor should perform the following checks and actions:
a) Check that all entries in the logbook have been addressed, check the event log in the panel and
take the necessary remedial actions.
b) Visually inspect the panel for any moisture ingress or other deterioration, check all battery
connections and test / check the alarm, fault and other functions of the panel operation.
c) Ascertain if any building or structural alterations have been carried out that would affect the
placement / location of call points or detectors. If so, perform a visual inspection.
d) Record in the logbook any defects or remedial actions that must be undertaken and arrange for
these to be carried out as soon as possible.

4.1.4 Annual Actions

The service / maintenance contractor should perform the following checks and actions:
a) Perform the checks as recommended above in the daily, monthly and quarterly schedules.
b) Perform a complete “Walk Test” of the system to check that each call point and detector is
operating to its manufacturers’ specification.
c) Visually inspect all cable fittings. Check that the equipment is undamaged and that the
conditions of installation have not changed such that they fall outside of the equipment
specifications.
d) Inspect and test all batteries and replace as required – refer to Section 4.2 for recommended
replacement schedule.
e) Record in the logbook any defects or remedial actions that must be undertaken and arrange for
these to be carried out as soon as possible.

Page 58 of 72
4.2 Replacement of Components
In general, all of the components parts used in the construction of the panel have been selected for
long life and reliability.
However, certain components may require to be changed on a regular service basis. The details of
these are as follows:

4.2.1 Batteries
For battery installation, see section 2.5.2

Respect the Environment.

Batteries must be disposed of responsibly and in accordance with any local
regulations.

4.2.1.1 Standby Batteries

Expected Life: - 3-5 years at an ambient temperature of 20°C
Replacement Schedule: - As above. However, note that the expected battery life is
shortened by increase in ambient temperature. The life
reduces by 50% for every 10°C rise above ambient. Refer
to battery manufacturer for further information.
Manufacturer / Part Numbers: - YUASA POWERSONIC
4AH NP4-12 5AH PS-1250
7AH NP7-12 7AH PS-1270
12AH NP12-12 12AH PS-12110
17AH NP18-12 18AH PS-12170
24AH NP24-12B 26AH PS-12260
38AH NP24-38 38AH PS-12380
45AH PS-12450

For optimum performance and charge retention, Yuasa recommend that

STOP batteries are ‘top-charged’ prior to installation.
For batteries up to 6 months old from date of manufacture, charge at 2.4V per
cell (i.e. 14.4V per battery) for 20 hours prior to installing the batteries.
It is not recommended to use batteries that are more than 6 months old, from
their date of manufacture, on a new installation.
It is quite normal for lead-acid batteries to vent hydrogen when
being charged.
The panel is adequately ventilated to dissipate this hydrogen.
DO NOT seal the enclosure or install in a sealed enclosure or
cavity.

Page 59 of 72
4.2.2 Liquid Crystal Display
Expected Life: - > 10 years
Replacement Schedule: - When the display becomes difficult to read. The display
contrast will gradually fade with time.
Manufacturer / Part Number: - Replace the complete display / keyboard assembly. Spare
part number MXS 504.

4.2.3 Spares
Part Number Description
MXS-501 1-LP Base Card including 1-Lp driver (AP/HO/AV)
MXS-501N 1-LP Base Card including 1-Lp driver (NITTAN)
MXS-502 2-LP Base Card including 2-Lp driver (AP/HO/AV)
MXS-502N 2-LP Base Card including 2-Lp driver (NITTAN)
MXS-503 4-LP Base Card including 1-Lp driver (AP/HO/AV)
MXS-503N 4-LP Base Card including 1-Lp driver (NITTAN)
MXS-504 Display Card (Common to all panel types)

For all other items, please refer to the sales part list for the sales item part number.

Page 60 of 72
5 Appendices
5.1 Appendix 1 – Forgotten Level 3 Password

Should the Level-3 password be forgotten, contact Customer Support to obtain a temporary permit
number to regain access to the panel programming functions.
Customer Support will require a decryption key displayed by the panel. To obtain this number,
attempt to gain access to the Level-3 Programming Functions entering “1” when prompted for the
password. As soon as the “Password Invalid” message is shown, press the “0” button and the
display will show a decryption key. Make a note of the first part of this number.
For example:
[Level 2 Menu]

Please Enter Your Password

214728378

Customer Support will provide a temporary permit number that you can enter when prompted for the
Level-3 password. As soon as access has been regained to the Level-3 Programming Functions,
select the Passwords Menu Option and check / change the Level-3 password. (Refer to Section
3.3.13 for further information).

Page 61 of 72
5.2 Appendix 2 – Recommended Fire Rated Cables
The following table provides a list of suitable fire rated cables with standard (30 minute) and
enhanced (120 minute) classification. Refer to Document No. 680-088 for an up to date list.

Core Sizes (mm) 5839-1 Rated

Manufacturer Cable Type Net
1.0 1.5 2.5 S (30) E (120)
AEI Firetec Multicore Ref. F1C 9 9 9 9
AEI Firetec Armoured Ref. F1C 9 9 9 9

Calflex Calflam CWZ 9

Cavicel SpA Firecel SR/114H 9 9 9

Cavicel SpA Firecel SR/114E 9 9 9 9

Draka Firetuf (OHLS) FTZ 9 9 9 9

Draka Firetuf PLUS 9 9 9 9

Huber & Suhner Radox FRBS/M1x2 9 9 9

Irish Driver-Harris Co Ltd Kilflam 2000 9 9 9 9

Irish Driver-Harris Co Ltd Kilflam 3000 9 9 9 9

Pirelli FP200 Flex 9 9

Pirelli FP200 Gold 9 9 9 9 9

Pirelli FP PLUS 9 9 9 9

Tratos Cavi SpA FIRE-safe TW950 9 9 9 9

Tyco Thermal Controls Mineral Insulated Twin Twisted PYRO-E CCM2T 9 9 9 9

Tyco Thermal Controls Pyrotenax Served Mineral Insulated Cable (light 9 9 9 9
and heavy duty)
Tyco Thermal Control Pyro-S 9 9 9 9

Wrexham Mineral Insulated Cable (light and heavy duty) 9 9 9 9

5.2.1 Detector Loop Lengths

With the above cables, loops can be up to 2Km in length. However, care must be taken when
designing the system to take into account the maximum loop loading. The voltage drop (load
current x cable resistance) over the cable always needs to be taken into account to ensure the
devices receive an adequate supply voltage. The following table gives recommendations for a loop.
(It may be possible to extend the lengths where the devices are distributed evenly – refer to the
device data sheets and Loop Calculators for further information on calculating loop loading, cable
cross sectional area and loop distance).

Maximum Circuit Circuit Max. Circuit Loop Cable Distance (M)

72Ω
Impedance Loading Impedance 2 2 2
1.0mm 1.5mm 2.5mm

Maximum Capacitance
230nF 100mA 55.0Ω 1500 2000 2000
(Core-Core)

Maximum Capacitance
410nF 200mA 27.5Ω 760 1130 1860
(Core-Screen)

Insulation Resistance
(Core-Core and Core- 72M Ω 300mA 18.3Ω 500 750 1200
Screen)

NB: Maximum Circuit Impedence is the sum

of the resistance of both cable conductors.
400mA 13.7Ω 380 560 920

500mA 11.0Ω 300 450 740

Page 62 of 72
5.2.2 Sounder Circuit Lengths
The voltage drop on each alarm circuit should be calculated to ensure that the minimum voltage at
the end of the circuit exceeds the minimum required by each sounding device at the minimum alarm
circuit output voltage.
The voltage at the end of the circuit is given by:
Minimum Alarm Voltage = VOUT(MIN) – (IALARM x RCABLE)

Minimum Output Voltage (VOUT(MIN)) is VBAT(MIN) – 0.5V = 20.5V

Alarm Current (IALARM) is the sum of the loads presented by the sounding devices in alarm
Cable Resistance (RCABLE) is the sum of the cable resistance in both cores x cable length.
Cable Resistance (RCABLE) for 1.0mm2 is 0.036Ω / metre
Cable Resistance (RCABLE) for 1.5mm2 is 0.024Ω / metre
Cable Resistance (RCABLE) for 2.5mm2 is 0.015Ω / metre

Insulation Resistance
(Core-Core and Core- 72M Ω
Screen)

5.2.3 Fire / Fault Routing Circuit Lengths

The voltage drop on each transmission circuit should be calculated to ensure that the minimum
voltage at the end of the circuit exceeds the minimum required by the relay coil at the minimum
circuit output voltage. Typically, relays will energise at 75% of their nominal drive voltage (i.e. 18V
for a 24V coil)
The voltage at the end of the circuit is given by:
Minimum Coil Voltage = VOUT(MIN) – (ION x RCABLE)
Minimum Output Voltage (VOUT(MIN)) is VAUX(MIN) – 0.8V = 19.7V
Maximum On Current (ION) is 35mA.
Cable Resistance (RCABLE) is as above.

Insulation Resistance
(Core-Core and Core- 72M Ω
Screen)

5.2.4 Network Cables

For a list of recommended cables, refer to the AdNeT document 680-502.

Page 63 of 72
5.3 Appendix 3 – Battery Standby Calculation Chart
Use the following charts and associated notes to calculate the size of the batteries required to
ensure operation of the installation in the event of AC Mains power failure. This chart is applicable to
all panels: Mx-5100, Mx-5200 and Mx-5400.
Quiescent Load Fire Alarm Load
Equipment I (A) x Total I (A) x Total
Chassis 0.072 1.0 = 0.072 0.125 1.0 = 0.125
Loop Driver 0.042 1.0 = 0.042 1.0 =
16
Loop 1 17
Sensor / Loop Current 1.25 = 1.25 =
Loop Driver 0.042 1.0 = 0.042 1.0 =
Loop 218
Sensor / Loop Current 1.25 = 1.25 =
Loop Driver 0.042 1.0 = 0.042 1.0 =
Loop 318 19
Sensor / Loop Current 1.25 = 1.25 =
Loop Driver 0.042 1.0 = 0.042 1.0 =
Loop 418 19
Sensor / Loop Current 1.25 = 1.25 =
Mxp-503 AdNeT Network Card 0.020 1.0 = 0.020 1.0 =
Mxp-509 AdNeT PLUS Network Card 0.043 1.0 = 0.043 1.0 =
20
Mxp-513 LED Indicator 0.008 = 0.030 =
20
Mxp-507 2-Way Relay Card 0.000 1.0 0.000 0.030 1.0 =
20
Mxp-532 Routing Interface 0.031 1.0 = 0.043 1.0 =
20 21
Mxp-504 VdS Interface 0.025 1.0 = 0.034 1.0 =
Mxp-504 VdS Interface Supply Outputs 1.0 = 1.0 =
22
Auxiliary Supply Output 1.0 = 1.0 =
Sounder Output A 1.0 =
Sounder Output B 1.0 =
18 19
Sounder Output C 1.0 =
18 19
Sounder Output D 1.0 =
Total ΣQuiescent Load = ΣAlarm Load =
x 24 hr = Ahr
x 48 hr = Ahr
x 72 hr = Ahr x 223 x 0.5 hr = Ahr
§ (carry forward) + Ahr
Total Load (Quiescent + Alarm) = Ahr
x 1.2523 (Battery De-rating factor) = Ahr

16
Use the detector manufacturers’ technical information to calculate the load on the loop for both the quiescent condition and
fire alarm condition for all loop devices. By default, a maximum of 5 detector / call point LED indicators will be turned on in a
fire alarm condition. (This number can be changed via the PC Programming Tool).
17
The calculated loop loading must be multiplied by a factor of 1.25 to calculate the actual current draw from the batteries.
This is to take into account voltage conversion and conversion efficiency in generating the supply for the loop.
18
Not available on Mx-5100.
19
Not available on Mx-5200.
20
Worst Case – All LEDS are ON. All Relays / Outputs are ON.
21
Does not include any supply loads for router, FAT, FBF, etc. Include these loads in the separate line.
22
Refer to separate data sheets for the additional modules that can be powered from the panel AUX Output to determine the
AUX loading currents. For example, the modules can include 4-Way Relay, 4-Way Sounder, Modem, Page, Sounder Splitter,
etc. The sum of all these additional currents should be entered in these fields. Ensure that the total alarm load does not
exceed the AUX output rating.
23
The alarm load should be doubled to allow for changes in battery efficiency for loads in excess of the recommended C/20
discharge rate. The total load calculated should be multiplied by a de-rating factor of 1.25 to allow for changes in battery
efficiency over time. The above calculation is in accordance with the recommendations in BS5839-1: 2002.
Page 64 of 72
5.4 Appendix 4 – Cause and Effect Programming Example
5.4.1 Introduction
By default, all sounders and output devices will turn on immediately as soon as a fire is detected
anywhere in the system. For example:
Cause Effect
Any Fire, Anywhere. Î ALL Output Devices will Turn ON

Quite often an installation will require a more complex “Cause and Effect” solution. Consider a
multiple story building where phased evacuation is required when a fire occurs on a particular floor.
For example:
Cause Effect
Any Fire on Floor 7 Î Sounders on Floor 6 will DELAY for 30 seconds, then start
(From Zones 22, 23 or 24) PULSING. After 2 minutes turn ON
Î Sounders on Floor 7 will Turn ON
Î Sounders on Floor 8 will DELAY for 30 seconds, then start
PULSING. After 2 minutes turn ON

5.4.2 Output Groups

There may be several sounders on each floor. These can be grouped together using the Output
Groups so that a single group number can easily reference all sounders on a particular floor in the
panel. For example:
Sounders Output Group
Assign All Sounders of Floor 6 Î Output Group 6
Assign All Sounders of Floor 7 Î Output Group 7
Assign All Sounders of Floor 8 Î Output Group 8

Refer to Section 3.3.2.9 for how to assign the output group to a loop output device. Refer to Section
3.3.20.1 for how to assign the output group to an internal panel circuit.

5.4.3 Styles
In the example, there are two ways in which the sounders should ring. These two operational
characteristics can be defined as Styles in the panel. For example:
The first Style is that the sounders should turn on immediately a fire is recognised in Zone 22 or in
Zone 23 or in Zone 24. The panel contains a default Style (Style 00) for this method of operation.
The second Style is that the sounders should stay silent for 30 seconds and then start pulsing. After
2 minutes of pulsing, they should then turn on. This is a little more complex but is easy to program.
In the following description, a new Style (Style 2) will be defined for this purpose.
It is quite likely that Style 2 will be used extensively in the cause and effect programming for the rest
of the building. For example, a fire on Floor 8 may also require the sounders on Floors 7 and 8 to
operate in this manner.

Page 65 of 72
5.4.4 Output Group Programming
To achieve the above cause and effect requirements, the three different Output Groups would be
programmed and indicated on the panel as in the following display examples:
Output Group 6 – Sounders on Floor 6:
[Output Group 6] [ 3.9% Mem used] [STYLE 02 ]

ZONE CAUSE STYLE=Delay->MODE Wait MODE Wait MODE

22 ANY FIRE 02 30s Pulse 120s On
23 ANY FIRE 02 30s Pulse 120s On
24 ANY FIRE 02 30s Pulse 120s On
More>

Output Group 7 – Sounders on Floor 7:

[Output Group 7] [ 3.9% Mem used] [STYLE 00 ]

ZONE CAUSE STYLE=Delay->MODE Wait MODE Wait MODE

22 ANY FIRE 00 - On
23 ANY FIRE 00 - On
24 ANY FIRE 00 - On
More>

Output Group 8 – Sounders on Floor 8:

[Output Group 8] [ 3.9% Mem used] [STYLE 02 ]

ZONE CAUSE STYLE=Delay->MODE Wait MODE Wait MODE

22 ANY FIRE 02 30s Pulse 120s On
23 ANY FIRE 02 30s Pulse 120s On
24 ANY FIRE 02 30s Pulse 120s On
More>

Page 66 of 72
5.5 Appendix 5 – Other Useful Documents
The following reference and application documents may be useful in the design, configuration and
installation of the system.
The latest versions are available from the Advanced Electronics Ltd web site (www.advel.co.uk) or
in hard copy format from Sales.

Document Title Type Description

Number
680-156 Configuration Tool Software Level 3 Tool Explains how to configure the panel using the PC-
NET-003 V5 PC Software.
NOTE: On-line help is provided within the PC
Software.
680-023 Logo Software Level 4 Tool Explains how to create and update the logo in the
panel using the PC-NET-007 PC software.
680-025 Key Switch Access Control Application Note Explains how to configure the panel for use of a
key switch for level 2 access.
680-502 Ad-NeT Network Product Data Explains how to install and configure the Ad-NeT®
and Ad-NeT-PluS®networks.
680-030 Flash Programming Level 4 Tool Explains how to update the panel firmware with
new software revisions.
680-034 External Printer Output Application Note Explains how to configure the panel and connect a
serial RS232 printer.
680-039 Class Change Programming Application Note Provides examples of how to implement a class
change function using different inputs.
680-042 Gated Time-Clock Application Note Explains how to use an input to enable / disable a
Programming time-click function.
680-058 Hochiki Sounders and Outputs Application Note Explains how to configure the panel for operation
with the ranges of sounders and output devices.
Also details limitations.
680-059 Apollo Ancillary Base Sounders Application Note Explains how to configure the panel for operation
with detector LED driven base sounders. Also
details limitations.
680-085 Software Upgrades Application Note Explains how to upgrade the software in the
Graphics Display Card and Fault Tolerant Network
Card. Refer to 680-030 for general panel software
flash programming information and guidance.
680-088 Cables for Fire Systems Application Note Gives further information on the cables than can
be used.
680-116 Minimizing False Alarms Application Note Details the diverse methods that can be
configured to assist in the reduction of false
alarms.

Page 67 of 72
5.6 Appendix 6 –Network Design Principles
This section gives recommendations on the design of the installation to cover specific EN54-2
requirements and typical national codes of practice.
[EN54-2: 1997, Clause 13.7] Not more than 512 fire detectors and / or manual call points and their
associated mandatory functions shall be affected as a result of a system fault in the C.I.E.

5.6.1 Mandatory Functions

For full compliance with the requirements in EN54-2, the configuration and operation of all
mandatory outputs shall comply with the guidelines below.
Sounder Devices [EN54-2: 1997 Clause 7.8]:
Care should be taken with the cause and effect programming to ensure that any sounder / sounder
output is configured such that its fire response operation will only be affected if there is a system
fault on the chassis / panel to which it is directly connected.
Consideration should also be given to the applicable code of practice or national standard
regulations for fire systems installation (for example BS5839-1: 2002) for installation and operation
of sounder devices.
Fire & Fault Routing [EN54-2: 1997 Clauses 7.9 & 8.9]:
Network: If provided, then at least two fire and fault routing interfaces should be provided. These
should be programmed to report all fire and all fault conditions.

5.6.2 Network Wiring

Where the installation design and codes of practice deem the network connections to be a 'Critical
Signal Path' then consideration should be given to the use of the Ad-NeT-PluS® Fault Tolerant
Network. For further information see document 680-502.
In addition, the routing and type of cables employed is important to limit the risk of multiple failures
causing overall or partial loss of the network functions. BS5839-1: 2002 Sections 24-2 and 26.2
provide a useful guide.

— Use fire resisting

cables.
— Configure the
network as a loop.
— Employ diverse
routing of incoming
and outgoing Detector Loop Wiring

circuits, except in the

immediate vicinity of
the sub-panel.
— There is no loss of
communication to
any sub-panel in the
event of a single
open or short circuit
on the loop.

Page 68 of 72
5.7 Appendix 7 – Mx Series Product Capabilities / Max Limits
This section gives details on the maximum capabilities for each of the products in the range. Some
of the items can only be utilised via the PC CONFIG tool and these are annotated accordingly.

Item 5100 5200 5400 5020 / Mxp- Mxp- Comments

5030 510 554

Max № of Loops 1 2 4 0 0 0
Max № of Resident Zones 200 200 200 100 200 200
Highest Resident Zone № 2000 2000 2000 2000 2000 2000
Max № of System Zones 2000 2000 2000 2000 2000 2000
Max № of Points 1000 1000 1000 9 - -
№ of On-board Points Depends on optional cards
fitted
№ of On-board Sounders 2 2 4 0 0 0
№ of On-board Relays 2(4) 2(4) 2(4) 0 0 0
(including Mxp-507 Card)
№ of Switch Inputs 9 9 9 9 - -
Max № of Time Clocks 10 10 10 -- 3 3
Max № of Ringing Styles 40 40 40 10 10 10
Max № of Output Groups 200 200 200 200 200 200
Max № of Output Group 1150 1150 1150 250 250 250 Requires PC CONFIG to
Lines define more than one line per
Output Group
Max № of Passwords 12 12 12 12 12 12
Max № of Sectors 100 100 100 100 100 100 PC CONFIG Only
Available
Max № of Input Events 250 250 250 100 100 250 PC CONFIG Only
Max № of Logic Blocks 100 100 100 50 50 50 PC CONFIG Only
24
Max № of Logic Terms 1500 1500 1500 100 100 100 PC CONFIG Only
Max First Loop № 99 98 96 -- -- -- PC CONFIG Only

24
Max № of logic terms available to the user depends upon the number of logic blocks defined. Each logic block requires a
terminator term. This terminator uses up one of the available logic terms. Therefore, the number of logic terms available for
use will be the Max № of Logic terms – the № of Logic blocks used – for example, using 20 logic blocks in an Mx-5400 will
give 500-20=480 Logic Terms available to use.
Page 69 of 72
This page is intentionally left blank.

Page 70 of 72
USER NOTES:

Page 71 of 72
Doc Number 680-165
Revision 03
First Issued 2010-01-19

Advanced Electronics Limited

34 Moorland Way
Nelson Park
Cramlington
Northumberland
NE23 1WE
Tel: +44 (0)1670 707 111
Fax: +44 (0)1670 707 222
Web: www.Advel.co.uk
Email: [email protected]