Revision: 2021-166

MQB Codings

© 2013-2021 Daniel Fuchs page 1

contents
Preface / Disclaimer 11
Extension, corrections and donations 11
Access permissions 11
Cornering lights - deactivation 13th
Cornering light - change standard / regulation 13th
Cornering light - change the dimming speed 13th
Cornering lights - adjust the speed threshold 13th
Low beam - automatic activation as permanent driving light from speed 13th
ACC - configure distance setting in MMI (Audi A3 8V) 13th
Allow ACC mode change 14th
ACC - change step setting to 1 km / h (Audi A3 8V) 14th
ACC - prevent / allow overtaking on the right (variant 1) 14th
ACC - prevent / allow overtaking on the right (variant 2) 14th
All-wheel drive locking measures increase for more traction 14th
Ambient lighting (multicolored) - activation / activation 15th
Ambient lighting (multicolored) - customize colors 16
Ambient lighting (multicolored) - colors expand to 30 possibilities 16
Ambient lighting (multi-colored) - change the color assignment to the driving profile 17th
Ambient lighting - Deactivate dimming of the door lighting 17th
Ambient lighting - adjust colors (Leon III 5F) 17th
Trailer coupling - activation / activation (retrofitting) 18th
Trailer Assist - Activation / activation 19th
Assistant light function - change light sensor sensitivity 20th
Deactivate exhaust flap control 20th
Auto Hold - Adaptation of the dynamic start-up assistant 20th
Auto Hold - state after restart 20th
Auto-Lock also locks the fuel cap 21st
Teach in battery after changing 21st
Deactivate the passenger airbag button 21st
Hill start assist - activation of the HHC 21st
© 2013-2021 Daniel Fuchs page 2
Hill start assistant - set hold time 21st
Rear indicator active when tailgate is open 22nd
Adjust brake disc drying 22nd
Coming Home / Leaving Home - emulation via interior light 22nd
Coming Home / Leaving Home - Set the light duration to> 30 seconds 23
Coming Home / Leaving Home without low beam (only daytime running lights or parking lights) 23
Coming Home / Leaving Home via fog lights 23
Coming Home / Leaving Home - daytime running lights at full strength 23
Coming Home - adapting the switch-on trigger 24
Coming home function automatically 24
Discover Media / Pro - Current location in the header instead of the selected driving profile 24
Discover Media / Pro - Activate off-road ads (MIB 2) 24
Activate Discover Media / Pro online services (MIB 2) 24
Discover Media / Pro - Activate WiFi streaming (MIB2) 25th
Discover Media / Pro - Allow second phone via Bluetooth 25th
Discover Pro - change boot animation 25th
Activate Discover Pro - Green Menu 25th
Discover Pro - View speed limit from map data 26th
Discover Pro - Deactivate radio modulation AM 26th
Discover Pro - Change skin 26th
Discover Pro - Activate WiFi streaming (MIB 1) 26th
Third brake light as a receipt for the central locking 26th
Third brake light active when the tailgate is open 27
The third brake light flashes when the hazard warning lights are active 27
DWA - activation / activation (retrofitting) 27
DWA - activation of the horn acknowledgment when locking and unlocking the vehicle 28
DWA - start of the alarm with mechanical opening (Thatcham) 28
Dynamic high beam (DLA) - activation (until MY 2016) 28
Dynamic high beam (DLA) - activation (from MY 2017) 29
Parking aid - change cut-out speed 29
Parking aid - deactivate activation tone 29
Parking aid - deactivate audio lowering 29
Parking aid - automatic activation when driving slowly forward 30th
© 2013-2021 Daniel Fuchs page 3
Parking aid - adjust curb distance (trigger continuous tone / last step) 30th
Parking aid - activate display, despite small parking aid (Leon III 5F, Audi A3 8V) 30th
Parking aid - activate / deactivate guide lines 30th
Parking aid - adjust volume front / rear 30th
Parking aid - adjust pitch front / rear 30th
Electronic parking brake (EPB) - deactivation of the automatic activation when the seat belt is removed 30th
ESP - change available modes (ASR off / ESC Sport / ESC off) 31
Activate driving school mode (display of speed and indicators on the radio, only possible with Composition Color / Touch and Discover Media) 31
Window operation - do not cancel the release run-on when opening the door 31
High beam assistant (Light Assist / HBA) - activation (variant 1) 31
High beam assistant (Light Assist / HBA) - activation (variant 2) 31
High beam assistant (Light Assist) - adjust switch-on and switch-off times 32
High beam assistant (Light Assist) - Deactivate reset 32
High beam assistant (Light Assist) - Deactivate city recognition 32
Recalibrate the front / apron camera after lowering 32
Front Assist - advance warning - activate early / medium / late selection 33
Front Assist - advance warning - save selected value 33
Windshield wipers - Park when the hood is opened 33
Windshield wipers - park when ignition is switched off (Octavia III 5E) 33
Front windscreen wiper - bring to service position via menu (Audi A3 8V) 33
Windshield wiper - activate tear wiping 33
Front wiper - adjust wipe cycles per minute 34
Front windscreen wiper - Activate front tear wiping 34
Windows release after-run after ignition off 34
Footwell lighting - activation / activation (retrofitting) 34
Footwell lighting - activation / activation multicolored (retrofitting) 34
Footwell lighting - activate the ambient lighting function (Audi) 35
Footwell lighting - conversion to LED - prevent error messages in the BCM 35
Deactivate the yellow mode switch light 35
Activate trailer stabilization 35
Deactivate gearbox freewheel 35
Tailgate (electric) - can be opened / closed while driving 36
Tailgate (electric) - opening / closing when towing a trailer 36
© 2013-2021 Daniel Fuchs page 4
Tailgate (electric) - open / close via button in the center console and FFB 36
Tailgate (electric) - change opening height 36
Tailgate (electric) - monitoring of keys in the trunk (KESSY) 36
Tailgate (electric) - Do not cancel closing when leaving the immediate area 37
Tailgate (electric) - allow closing with the key from a greater distance 37
Tailgate (electric) - adjust or deactivate warning signals 37
Close tailgate with a time delay after individual opening (30 sec) 37
Tailgate lights stay on when the flap is opened (Golf 7 AU, Audi A3 8V) 37
Rear window heating - adjust heating time 38
Deactivate the rear wiper 38
Rear wiper - activate automatically when the front wiper is active at level 2 or higher 38
Rear wiper - deactivate automatic wiping when reverse gear is engaged 38
Rear wiper - activate tear wiping 38
Rear wiper - adjust the wiper interval 38
Move the HUD display horizontally 38
Move the HUD display vertically 39
Infotainment - activate Apple Wireless Carplay (Audi) 39
Infotainment - remove or activate the ejection lock 39
Infotainment - activate the welcome sound (Audi) 39
License plate lighting - conversion to LED 39
KESSY - automatic locking when the doors are closed (3Q0 control unit) 39
KESSY - automatic locking when closing the doors (5Q0 control unit) 40
KESSY - Activate the staging / pulsing of the start button 40
Activate KESSY - convenience opening 40
KESSY - Temporary deactivation - activation (3Q0 control unit) 40
KESSY - Temporary deactivation - activation (5Q0 control unit) 41
Deactivate KESSY door sensors 41
KESSY - Activate locking via Easy Close (3Q0 control unit) 41
Air conditioning - Air Care - activation 41
Air Conditioning - Air Care - Save State 41
Air conditioning - adjust the sensitivity of the indoor humidity sensor 41
Air conditioning - adjust blower logic in AUTO mode 42
Air conditioning - show blower level also in AUTO mode (not Audi A3 8V) 42
© 2013-2021 Daniel Fuchs page 5
Air conditioning - change the brightness of the LCD temperature display 42
Air conditioning - brightness LEDs for current fan level 42
Air conditioning - brightness LEDs for seat heating 42
Air conditioning - brightness LEDs (rest) 42
Air conditioning - Activate offset logic for the fan speed 43
Combination instrument - deactivate seat belt reminder 43
Instrument cluster - change reserve tank volume 43
Combination instrument - scale lighting also active with parking lights 43
Instrument cluster - change skin 43
Combination instrument - change scale display (VC / AID / FPK) 43
Combination instrument - adjust speedometer maximum (VC / AID / FPK) 44
Combination instrument - activate pointer test (staging) 44
Combination instrument - ignition active Adapt / deactivate message 44
Comfort actions via FFB even while the ignition is on / engine is running 44
Comfort flashing Change the flashing cycle 44
Deactivate convenience flashing 44
Change the steering characteristic without selecting a driving profile 44
Steering wheel heating - automatic activation 45
Adjust steering assistance 45
Adjust steering assistance directly when changing driving profiles (instead of incremental changes) 45
Adjust light switch-on threshold (Leon III 5F) 45
Headlight flasher also activates fog lights 45
Headlight flasher during the day via fog lights 46
Headlight flasher possible with ignition off 46
Light / rain sensor - activation / activation (retrofitting) 46
Light / rain sensor - activate rain closing 47
MFA - adjust display time for rear seat belt display 47
MFA - adjust display duration for service reminder 47
MFA - adjust display duration for warning messages 47
MFA - briefly display travel profile when changing 48
MFA - Deactivate the "Switch on dipped headlights" message 48
MFA compass at the bottom 48
MFA - Show the volume to be refilled 48
© 2013-2021 Daniel Fuchs page 6
MFA - show oil temperature 48
MFA - show lap counter / lap timer 48
MFA - show shift recommendation (Audi A3 8V) 48
MFA - warning when driving with a rear fog light 48
MFA - warning when driving with active parking lights 49
MFA - warning at speeds over 120 km / h 49
MFA - Adapt / deactivate warning notice danger of slippery sides 49
MFA - warning sign of danger of slipperiness resubmission after engine off 49
MFA - Display cylinder deactivation (ACT / COD) 49
Adjust microphone sensitivity 49
Multifunction steering wheel - activation / activation (retrofitting) (Audi A3 8V) 49
Fog lights - activation / activation (retrofitting) 50
Fog lights - activate cornering lights 50
Fog lights - activate intersection light 51
Fog lights - conversion to LED (Octavia III 5E) 51
Rear fog lights - both active (Octavia III 5E) 51
Personalization - activation (variant 1) 52
Personalization - activation (variant 2) 52
Pace car flashing taillights (LED taillights) (Golf 7 AU) 53
Pace car flashing of the taillights (only when opening / closing the vehicle) (LED taillights) (Golf 7 AU) 53
Pace car flashing of the rear lights (only with hazard warning lights) (LED rear lights) (Golf 7 AU) 54
Parking light on both sides 54
Radio receiver amplifier 55
Tire pressure control display (direct, TPMS) - activation / activation 55
Tire pressure control display (indirect, via ABS) - activation / activation (retrofitting) 56
Rear view camera (low) - activation / activation (retrofitting) 56
Reversing camera (low) - Deactivate deactivation when the tailgate is open 56
Reversing camera (low) - Switch off speed-dependent deactivation 56
Increase reversing light luminosity (Golf 7 AU) 56
Headlight cleaning - deactivate SWRA 57
Sunroof - make the opening position accessible directly from the sliding position 57
Sunroof - Do not cancel the closing process when opening the door (with STG CA) 57
Sunroof - Do not cancel the closing process when opening the door (without STG CA) 57
© 2013-2021 Daniel Fuchs page 7
Sunroof - change mode when opening comfortably 57
Sunroof - decouple the roller blind from the roof (with STG CA) 57
Sunroof - decouple the roller blind from the roof (without STG CA) 58
At the bottom of the list for Coming Home / Leaving Home 58
Tail light inside double function as brake light (for LED taillights) (Golf 7 AU) 58
Tail light inside double function as brake light (for halogen taillights) (Golf 7 AU) 58
Tail light inside Deactivate double function as brake light when the rear fog light is active (legal requirement according to StVZO) 58
Seats - activate comfort entry "Easy Entry" (electric seats) 59
Seats - Comfort entry "Easy Entry" activate menu item (electric seats) 59
Seat heating - adjust the temperatures of the levels 59
Seat heating - save the selected seat heating level 60
Seat heating - adjust withdrawal thresholds (Audi A3 8V) 60
Set daylight saving time automatically 60
Deactivate the sound actuator or reduce the volume 60
Sound system - expansion of the internal sound system (without external amp) with virtual surround and subwoofer 60
Mirror - Activate lowering of the passenger side 60
Mirror - folding - activation 61
Mirror - folding is also active while driving 61
Adjust mirror folding in FFB mode 61
Mirror heating automatically activated when the rear window heating is activated 61
Mirror - heating permanently active when switched on once 61
Mirror - Surrounding lighting is active when the mirrors are folded in 62
Spoiler - do not lower when locking the vehicle (Audi TT 8S) 62
Spoiler - do not lower automatically after manual extension (Audi TT 8S) 62
Activate voice control (Audi A3 8V) 62
Lane Assist - activation (variant 1) 62
Lane Assist - activation (variant 2) 63
Lane Assist - activation (variant 3) 64
Lane departure warning - activate adaptive lane guidance via the steering column button 65
Lane departure warning - deactivation threshold for driver inactivity 65
Lane departure warning - Set the time of intervention via the menu 65
Lane departure warning - adjust the intensity of the steering wheel vibration 65
Lane departure warning - adjust the intensity of the steering assistance 65
© 2013-2021 Daniel Fuchs page 8
Lane departure warning - save the last switch-on status 65
Lane departure warning - set warning strength via menu (variant 1) 65
Lane departure warning - set warning strength via menu (variant 2) 66
Auxiliary heating - adjust the post-heating time 66
Auxiliary heating - adjust the temperature for activating the interior fan 66
Auxiliary heater - adjust temperatures for auxiliary heater operation 66
Deactivate the start / stop function 66
SWRA - deactivation 67
SWRA - change delay time until triggering 67
SWRA - adapt washing behavior (frequency, duration) 67
Daytime running lights - switch off when the handbrake is on 67
Daytime running lights - dimming when blinking 67
Daytime running lights - dimming when blinking (slow dimming) (Seat Leon 5F) 68
Daytime running lights - deactivate dimming when flashing (Audi A3 8V) 68
Daytime running lights - Simultaneous flashing with the turn signal (or alternately) 68
Daytime running lights - Inactive in LDS position 0 69
Daytime running lights - activate the menu item in the CAR menu 69
Daytime running lights - fog lights only as daytime running lights 69
Daytime running lights - add fog lights in addition to daytime running lights 69
Daytime running lights - taillights additionally active (with KZB and inside button = parking light always active) 69
Daytime running lights - taillights additionally active (without KZB) 69
Daytime running lights - parking light point additionally active (Golf 7 AU) 70
Fuel gauge - adjustment / calibration 70
Adjust button illumination (driving profile, ASR, ESP) brightness 70
Traffic Jam Assist & Emergency Assist - activation 70
Surrounding lighting - activation / activation (retrofitting) 71
Surrounding area lighting - use as a maneuvering light 71
US parking light explicitly only in the parking light switch position 71
Emulate US parking light via ambient lighting (dimmable / switchable in the CAR menu) 71
Control US parking lights via the Sport driving profile (Leon III 5F) 72
US daytime running lights or parking lights (indicators permanently dimmed for daytime running lights or parking lights / low beam) 73
US daytime running lights or parking lights - dimming is canceled when flashing 73
US daytime running lights in addition to normal daytime running lights - switchable via the CAR menu 74
© 2013-2021 Daniel Fuchs page 9
US daytime running lights / normal daytime running lights - switchable via the CAR menu 75
Adjust consumption display 76
Activate voice control (Audi A3 8V) 76
Traffic sign recognition - activation (variant 1) 76
Traffic sign recognition - activation (variant 2) 76
Traffic Sign Recognition - Show cancellation signs 77
Video in Motion (VIM) activation 77
Hazard warning lights - automatic activation after emergency braking 77
Hazard warning button - adjust the brightness of the lighting 77
XDS - Advanced electronic differential lock adjust control strength 77
Central locking - adjust the duration of the visual feedback 78
Central locking - Do not unlock when removing the key 78

© 2013-2021 Daniel Fuchs page 10

Preface / Disclaimer
The codings and adaptations listed here have been tested from various sources and mostly on a vehicle or found and documented yourself. This document
does not claim to be correct. All changes are therefore made at your own risk.

It is recommended to create a complete auto-scan and adaptation channel images ("AdpMap") of all control units that are to be adapted before making
changes.

Instructions for creating an adaptation channel image:

Start VCDS> Applications> Control unit image> Address "XX", access authorization "YYYYY", function "Adaptation", format "CSV file"> Start The access
authorizations can be found in the next chapter.

In newer VCDS versions, images of all control units in the vehicle can be created instead of just one address. This is recommended the first time you come into
contact with a vehicle!

Extension, corrections and donations

I would be happy if corrections and additions were made to me so that I can add them to the list as soon as possible.

This overview is created exclusively in my free time. As a private project, I don't receive any payment for this. I hope that this will save time not only for myself,
but also for others by not having to search through thousands of websites. Since time is also money, I am of course happy to receive any kind of financial
support.

Donations are gladly accepted via PayPal: https://www.paypal.me/vagcoding

Access permissions
Control unit Log in function

01 (engine electronics) 27971 Activation of the adaptation

79153 ???

12233 Injector adaptation / calibration

© 2013-2021 Daniel Fuchs page 11

03 (brake electronics) -------- (Logins without a known function are not listed for this STG due to the quantity)

11966 Activation of the adaptation of the hydraulic brake assistant (IDE05055)

20103 Activation of the adaptation of the ext. electronic differential lock XDS (IDE05286)

24990 Activation of the adaptation

25757 Activation of the adaptation of the brake stabilization (IDE05161)

25004 Brake booster adaptation

31857 Activation of the basic setting and adjustment

40168 Activation of the basic setting

40304/44595 Activation of the adjustment of the brake disc drying (IDE04456)

37203 Activation of the adaptation of the driver's door query (IDE03493)

05 (access / start area) 20103 ???

08 (air conditioning / heating 20103 ???

el.)

09 (central electrics) 20107 ???

31347 Activation of the adaptation

42013 ???

48396 Activation of the adaptation (only Tiguan MY 2016)

10 (parking aid 2) 20103 ???

71679 Activation of the coding

13 (distance control) 14117 Activation of the adaptation

© 2013-2021 Daniel Fuchs page 12

14 (wheel damping) 20103 ???

17 (dash panel insert) 20103 Activation of the adjustment (before MY 2016)

25327 ??? (from MY 2016)

47115 Activation of the adjustment (from MY 2016)

18 (auxiliary heating) 20103 ???

80782 Activation of adjustment of the control parameters

19 (diagnostic interface) 20103 ???

2B (steering column lock) 20103 ???

3C (lane change) 20103 ???

42 (door electr. Driver) 20103 ???

44 (power steering) 19249 Activation of the adaptation

28183 Activation of the adaptation of the travel profile switching (IDE06419)

44595 ???

4B (multifunctional control) 20103 ???

52 (door electr., Passenger) 20103 ???

55 (headlight range control) 15284 Activation of the adaptation

20103 ???

5F (Information Elect. I) 20103 ???

65 (tire pressure) 20103 Activation of the adaptation

6D (tailgate) 12345 Activation of the adaptation

A5 (front / front camera) 20103 Activation of the adaptation

© 2013-2021 Daniel Fuchs page 13

75 (telematics) 20103 ???

CA (sunroof elec.) 20103 Activation of the adjustment and basic setting

Cornering lights - deactivation

STG 09> Access authorization: 31347> Adaptation> Channel "Static cornering light regulation"> Change value to "off" (factory setting: ECE R119)

Cornering light - change standard / regulation

STG 09> Access authorization: 31347> Adaptation> Channel "Static cornering light regulation"> Adapt value

"ECE R119" > The cornering light is already activated when the vehicle is stationary (factory setting) "ECE R48" > The cornering light is only activated
from 1 km / h, i.e. only when rolling away

Cornering light - change the dimming speed

STG 09> Access authorization: 31347> Adaptation> Channel "static cornering light dimming speed"> Adapt value [% value per second] (factory setting: 50% per
second = 2 seconds)

Cornering lights - adjust the speed threshold

STG 09> Access authorization: 31347> Adaptation> Channel "static cornering light - upper speed threshold"> Adapt value in km / h (factory setting: 40)

Low beam - automatic activation as permanent driving light from speed

STG 09> Access authorization 31347> Adaptation> ...

> Channel "Driving lights and parking lights / all-weather light switch-on limit"> Adjust speed in km / h
> Channel "Driving lights and parking lights / all-weather light switch-off limit"> Adjust speed in km / h

© 2013-2021 Daniel Fuchs page 14

ACC - configure distance setting in MMI (Audi A3 8V)
STG 13> Access authorization: 14117> Adaptation> Channel "Selection option for presetting the time gap"> Change value to "on"

Allow ACC mode change

After coding, the distance control mode can be set between the ACC, Cruise Control (Tempomant) and Limiter modes in the assistant menu. The minimum
requirement for this coding is currently unknown - successfully tested on 5Q0 907 572 R, SW 0771.

STG 13> Coding> Byte 24> Activate bit 4 ("Cruise_control_mode")

ACC - change step setting to 1 km / h (Audi A3 8V)

STG 13> Coding> Byte 14> Activate bit 4 ("Operation_mode")

ACC - prevent / allow overtaking on the right (variant 1)

An ACC control unit with part number 5Q0 is required.

STG 13> Access authorization: 14117> Adaptation> Channel "Avoidance of impermissible overtaking"> Change value to "on" or "off"

ACC - prevent / allow overtaking on the right (variant 2)

An ACC control unit with part number 3Q0 or 2Q0 is required.

STG 13> Coding> Byte 02> Bit 5 activate or deactivate ("Overtaking Right Prevention active")

All-wheel drive locking measures increase for more traction

For this function, the software version of the all-wheel drive control unit should be at least 7083. It may be necessary to update this to a compatible version
beforehand.

STG 22> Coding> Byte 00> ...

> Deactivate bit 0> Activate bit 1 and 2

© 2013-2021 Daniel Fuchs page 15
STG 22> Adaptation> ...

> Channel "Acoustic measure: Bracing logic"> Adjust value to "Increased traction"
> Channel "acoustic measure: gasoline anti_hum_measure_benzin_gear_4"> adjust value to "no measure"
> Channel "acoustic measure: gasoline anti_hum_measure_benzin_gear_5"> adjust value to "no measure"> channel "acoustic measure: gasoline
anti_hum_measure_benzin_gear_6"> adjust value to "no measure"> channel "acoustic measure: gasoline anti_hum_measure"> measure up_7 gasoline
anti_hum_measure_benzin_gear_6 " adjust> Channel "acoustic measure: petrol engine anti_impact_driver_measure_benzin_gear_4"> adjust value to "no
measure"> channel "acoustic measure: petrol engine anti_impact_driver_measure_benzin_gear_5"> adjust value to "no measure"> adjust value to "no
measure"> channel "acoustic measure: petrol engine anti_impact"> channel "acoustic measure: petrol engine anti_impact" "adjust> channel" acoustic
measure:Petrol-Anti_impact_driver_measure_benzin_gear_7_plus "> adjust value to" no measure "> channel" acoustic measure: Diesel-
Anti_hum_measure_diesel_gear_4 "> adjust value to" no measure "> channel" acoustic measure: Diesel-anti_hum_measure_5 "> adjust value to"
channel_5 acoustic measure "> : Diesel-Anti_hum_measure_diesel_gear_6 "> adjust value to" no measure "> Channel" acoustic measure: Diesel-
Anti_hum_measure_diesel_gear_7_plus "> adjust value to" no measure "> Channel" acoustic measure: Diesel-Anti_impact_driver_measure_4 "> adjust
value channel_4" measure_diesel_gear " Acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_5 ">Adjust value to "no measure"> channel
"acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_6"> adjust value to "no measure"> channel "acoustic measure: Diesel-
Anti_impact_driver_measure_diesel_gear_7_plus"> adjust value to "no measure"

Ambient lighting (multicolored) - activation / activation

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior light 2nd generation - soft color change"> Adjust value to "active" (if desired)> Channel "Interior light 2nd generation multi-color center
console lighting"> Adjust value to "active" (if installed)> Channel "Interior light 2. Generation instrument panel lighting multi-colored "> Adjust value to"
active "(if AID installed)> Channel" Interior light 2nd generation loudspeaker lighting multi-colored "> Adjust value to" active "(if installed)> Channel" Interior
light luminaire configuration-Ambiente_Applikationsträger_in_Instrumententafel "> value Adjust "built-in"> channel "interior light, luminaire configuration-
center console lighting"> adjust value to "built-in" (if built-in)> channel "Interior light luminaire configuration-Frei_Farbwahl_ueber_HMI "> adjust value to"
not active "
> Channel "Interior light luminaire configuration-Ambient_Farbliste_HMI"> Adjust value to "active"> Channel "Interior light luminaire configuration-
ambience menu with all zones"> Adjust value to "active"> Channel "Interior light luminaire configuration-ambience menu with global off"> Value to "active"
adjust

After completing the coding, the infotainment must be restarted via the reset (hold the power button for 10 seconds).

© 2013-2021 Daniel Fuchs page 16

Ambient lighting (multicolored) - customize colors
The colors are specified in RGB coding. If a color is set to {R: 0, G: 0, B: 0}, the color is not displayed. The first three channel blocks act for the infotainment and
the AID, the second three blocks for the LED ambient strips, which are controlled via the LIN bus. After completing the coding, the infotainment must be
restarted via the reset (hold the power button for 10 seconds).

Note: The colors are usually reproduced 1: 1 in infotainment and AID. Slight adjustments may be necessary for the LIN colors, as the colors may differ due to the
different luminosity of the LEDs.

STG 09> Access authorization: 31347> Adaptation> ...

> Channels "Ambient light color list - red value color?" > Adjust values in the range of 0-255> Channels "Ambient light color list-green value color?" > Adjust
values in the range of 0-255> Channels "Ambient light color list-blue value color?" > Adjust values in the range of 0-255> Channels "Interior light 2nd
generation - red value color?" > Adjust values in the range of 0-255> Channels "Interior light 2nd generation green value color?" > Adjust values in the range
from 0-255> Channels "Interior light 2nd generation blue value color?" > Adjust values in the range from 0-255

or (with newer control units)

> Channels "Ambient light color list red value"> Adjust values in the range from 0-255> Channels "Ambient light color list green value"> Adjust values in the
range 0-255> Channels "Ambient light color list blue value" Color? "> Values in the range from 0-255 adjust> channels "Ambientelicht color list LIN-
Rotwert_Farbe _? _ Lin"> Adjust values in the range of 0-255> Channels "Ambientelicht color list LIN-Gruenwert_Farbe _? _ Lin"> Adjust values in the range
from 0-255> Channels "Ambientelicht color list LIN -Blauwert_Farbe _? _ Lin "> Adjust values in the range of 0-255

Ambient lighting (multicolored) - colors expand to 30 possibilities

With »Facelift BCMs« (from index BA) there are 20 more color sets, which are assigned to the group Ambience_lightning_color_list_2 &
Ambience_lightning_color_list_lin_2. The procedure is analogous to the adjustment of the colors in the previous chapter.

STG 09> Access authorization: 31347> Adaptation> ...

> Channels "Ambience_lightning_color_list_2-Red value color?" > Adjust values in the range of 0-255> Channels "Ambience_lightning_color_list_2-
Gruenwert Farbe?" > Adjust values in the range of 0-255> Channels "Ambience_lightning_color_list_2-Blue value color?" > Adjust values in the range from
0-255
> Channels "Ambience_lightning_color_list_lin_2-Rotwert_Farbe _? _ Lin> Adjust value in the range of 0-255> Channels"
Ambience_lightning_color_list_lin_2-Gruenwert_Farbe _? _ Lin> Adjust value in the range of 0-255> Channels "Ambience_lightning_color_list_lin_2-
Blauwert_Farbe? adjust

© 2013-2021 Daniel Fuchs page 17

Ambient lighting (multi-colored) - change the color assignment to the driving profile
STG 19> Coding> Byte 11> Activate bit 7 ("FPA_Function_AMB")

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior light 2nd generation-Ambiente_Farbwahl_FPA_waehlbare_Kopplung"> Adjust value to "active"> Channel "Interior light 2nd generation-
Ambiente_Farbwahl_FPA_waehlbare_Kopplung_Status_hmi_default"> Adjust value to "coupled"> Channel "Ambientelicht Assignment of color to driving
profile-driving profile_?" > Adjust the value as required

The assignment can be different depending on the gateway. This may have to be tried out. The color values are retrieved from the channel list "Ambient light
color list" and "Ambient light color list LIN". The function must then be activated in the CAR menu under ambient lighting.

Ambient lighting - Deactivate dimming of the door lighting

In the standard configuration, the ambient light is dimmed when the doors are closed and while driving. This can be deactivated.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior lighting parameter-p_helligkeit_Tueren_ Closed_HD_zu_zuendung_aus_tueren"> Adjust value to "100%"> Channel "Interior lighting
parameter-p_helligkeit_Fzg_ Closed_zuendung_ein_tueren"> Adjust value to "100%"

Ambient lighting - adjust colors (Leon III 5F)

STG 09> Access authorization: 31347> Adaptation>… (example: always red)

> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function A 17"> Adjust value to "not active" (factory setting: Ambient light 3)> Channel
"Luminaire16BLK SLB35BLK SL KC9 light function B 16"> Adjust value to "Ambient light 3" (Factory setting: not active)

Trailer coupling - activation / activation (retrofitting)

The adaptation in the engine control unit (STG 01) is not accepted for some models. In this case this can be ignored. Control units that are not installed can also
be ignored. It should be noted that some coding steps must be carried out depending on the installed part numbers.

STG 19> Activate installation list> "69 - Trailer"

© 2013-2021 Daniel Fuchs page 18

STG 01> Coding> Byte 05> Activate bit 4 ("Trailer installed")

STG 03> Access authorization: 24990> Adaptation> Channel "trailer stabilization"> Set value to "activated"

STG 09>

(for vehicles with coding »SW parts index <BA)

> Coding> ...

> Set byte 01> bit 0-7 to "01 Trailer Connector Diagnosis active"> byte 03> set bit 0-7 to the appropriate entry (see retrofitting instructions)

or

(for vehicles without coding »SW parts index> = BA)

> Access authorization: 31347> Adaptation> Channel "Networking trailer connection device"> Set value to "built in"

STG 10> Access authorization: 71679> Coding> Byte 03> Bit 0-1 set to "01 Trailer Hitch installed (manually removable)"

STG 13> ...

(with SW part number 5Q0 up to and including index F)

> Access authorization: 14117> Coding> Byte 02> Activate bit 3

or

(for SW part numbers 2Q0, 3Q0 and 5Q0 from index G)

> Access authorization: 20103> Coding> Byte 03> Activate bit 3

STG 34> coding> byte 00> activate bit 7 ("trailer, 0 = not installed / 1 = installed")

STG 3C> Coding> ...

(with SW part number 5Q0)

> Byte 02> Bit 4-7 set to "20 ECU for draw bar, with ECU for draw bar"

or

(with SW part numbers 2Q0 and 3Q0)

> Set byte 00> Bit 4-7 to "10 ECU for draw bar, with ECU for draw bar"

© 2013-2021 Daniel Fuchs page 19

STG 6C> coding> byte 04> activate bit 0 ("equipment_ahk, installed")

STG 6D> coding> byte 01> activate bit 7 ("trailer, 0 = not installed / 1 = installed")

STG A5> Access authorization: 20103> Coding>…

(with SW part number 5Q0)

> Set byte 16> bit 0-7 to "01 trailer_control_module, installed"

or

(with SW part number 3Q0)

> Byte 11> activate bit 0 ("AAG, 0 = not_coded / 1 = coded")

or

(with SW part number 2Q0)

> Byte 05> activate bit 4 ("AAG, 0 = not_coded / 1 = coded")

STG 69> Coding>…

> Set byte 01> Bit 0-3 to "01 Diagnosis of the line to the socket, active"> Set byte 03> Bit 0-3 to "01 Terminal 30 output (pin 9 socket), activated"

Trailer Assist - Activation / activation

RFK High or Area View (STG 6C) is required.
Note: The adjustments in the STG 5F only need to be carried out if problems arise when displaying the image in the infotainment system (e.g. no image, only
image for a trailer, etc.).

Activate STG 10> Coding> Byte 00> Bit 3

Activate STG 17> Coding> Byte 12> Bit 5

Activate STG 6C> Coding> Byte 10> Bit 3

STG 5F> Adaptation> ...

© 2013-2021 Daniel Fuchs page 20

 > Channel "Car_Function_Adaptations_Gen2-menu_display_trailer_assistant_after_disclaimer"> value to "enabled"> Set channel
"Car_Function_Adaptations_Gen2-menu_display_trailer_assistant_over_threshold_high"> value to "enabled"> Set channel "Car_Function_List_BAP_Gen2-
Trailer_Assistant_0x36"> value to "enabled"> Set channel "Car_Function_List_BAP_Gen2-Trailer_Assistant_msg_bus_0x36"> Set the value to "Terminal 15"

Assistant light function - change light sensor sensitivity

STG 09> Access authorization: 31347> Adaptation> Channel "Assist light functions - light sensor sensitivity"> Adapt value (factory setting: normal)

Deactivate exhaust flap control

STG 01> Coding> Byte 09> Deactivate bit 2

Auto Hold - Adaptation of the dynamic start-up assistant

STG 03> Adaptation> Channel "Dynamic approach assistant"> Adapt value

"Early" > The brake is released quickly and with little gas (barely noticeable, no jerk) "Normal" > Factory setting (jolt noticeable) "Late" > Brake
releases late and only with a lot of gas (strong jerk)

The factory setting "Normal" can be a problem when maneuvering because you have to accelerate a little more until the brake is released. This can be critical,
especially in tight parking spaces, because the car leaps forward. The "Early" setting is ideal if you want to use Auto Hold!

Auto Hold - state after restart

STG 03> Adaptation> Channel "Auto Hold Functional State"> Adapt value

"Last setting" > Factory setting, active / inactive is controlled via a button in the center console "Never active" > Auto-Hold always
deactivated after ignition change
"Always active" > Auto-Hold always activated after ignition change

Auto-Lock also locks the fuel cap

STG 09> Access authorization: 31347> Adaptation> Channel "Access control - speed-dependent tank cap lock"> Set value to "active"

© 2013-2021 Daniel Fuchs page 21

Teach in battery after changing
STG 19> Adaptation> Channels "Battery Adaptation"> Set values according to the installation

Deactivate the passenger airbag button

STG 15> Access authorization: 20103> Adaptation> Channel "Airbag adaptions key switch"> Set value to "not parameterized"

Hill start assist - activation of the HHC

STG 03> Coding> ...

> Byte 25> activate bit 0> byte 25> activate bit 1 (not with all-wheel drive)

Hill start assistant - set hold time

STG 03> Adaptation> "Hill start assist" channel> Adapt value

"Early" > The brake is released quickly and with little gas (hardly or not at all noticeable, no jerk)
"Normal" > Factory setting (jolt noticeable)
"Late" > Brake releases late and only with a lot of gas (strong jerk)

Rear indicator active when tailgate is open

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light18BLK HLA60 light function C 18"> Set value to "Rear lid open"> Channel "Light18BLK HLA60 dimming value CD 18"> Set percentage value as
desired (factory setting: 0)> Channel "Light19BLK HRC31 light function C 19"> Value set to "trunk lid open"> channel "lamp19BLK HRC31 dimming value CD
19"> set percentage value as desired (factory setting: 0)

Adjust brake disc drying

STG 03> Access authorization: 40304> Adaptation> Channel "Brake disc drying"> Adapt value ("not activated", "weak", "medium", "strong")

© 2013-2021 Daniel Fuchs page 22

Coming Home / Leaving Home - emulation via interior light
If the vehicle does not have a coming home / leaving home, this can be emulated using the interior light function. For this purpose, the light function must be
assigned to the corresponding luminaires. Attention: The lights can differ, here using the example of a Golf 7.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire4TFL LB4 light function E 4"> Set value to "Interior light"> Channel "Luminaire4TFL LB4 dimming value EF 4"> Set value to "100">
Channel "Luminaire5 TFL RB32 light function E 5"> value to "Interior light "set> channel" luminaire5 TFL RB32 dimming value EF 5 "> set value to" 100 ">
channel" luminaire2SL VLB10 light function E 2 "> set value to" interior light "> channel" luminaire2SL VLB10 dimming value EF 2 "> value on Set "26">
Channel "Luminaire3SL VRB21 light function E 3"> Set value to "Interior light"> Channel "Luminaire3SL VRB21 dimming value EF 3"> Set value to "26"
> Channel "Light20BR LA71 light function F 20"> Set value to "Interior light"> Channel "Light21BR RC8 light function F 21"> Set value to "Interior light">
Channel "Light23SL HLC10 light function D 23"> Value to "Interior light" set> channel "lamp24SL HRA65 light function D 24"> set value to "interior light">
channel "lamp25KZL HA59 light function C 25"> set value to "interior light"> channel "lamp25KZL HA59 dimming value CD 25"> value to "100 " set

Coming Home / Leaving Home - Set the light duration to> 30 seconds
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Comfort lighting - menu setting coming home"> Adjust value in seconds (value range: 0-90)> Channel "Comfort lighting - menu setting leaving
home time via BAP"> Adjust value in seconds (value range: 0-90)

Coming Home / Leaving Home without low beam (only daytime running lights or parking lights)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Comfort lighting - Coming Home lights"> Set value to "Low beam"> Channel "Luminaire6ABL LC5 light function C 6"> Set value to "not active"
(factory setting: Coming Home or Leaving Home active)> Channel "Luminaire7ABL RB1- Light function C 7 "> set value to" not active "(factory setting:
Coming Home or Leaving Home active)> channel" luminaire 6ABL LC5-Dimming Direction CD 6 "> set value to" minimize "> channel" luminaire 7ABL RB1-
dimming direction CD 7 "> Set the value to" minimize "

Coming Home / Leaving Home via fog lights

STG 09> Access authorization: 31347> Adaptation> Channel "Comfort lighting - Coming Home lights"> Set value to "Fog light"

© 2013-2021 Daniel Fuchs page 23

Coming Home / Leaving Home - daytime running lights at full strength
(Skoda Octavia 3 5E)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire2SL VLB10 dimming value CD 2"> Set value to "100"> Channel "Luminaire3SL VRB21 dimming value CD 3"> Set value to "100"

(VW Golf 7 AU among others)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light2SL VLB10 light function B 2"> Set value to "Coming Home or Leaving Home active"> Channel "Light3SL VRB21 light function B 3"> Set value
to "Coming Home or Leaving Home active"

Coming Home - adapting the switch-on trigger

STG 09> Access authorization: 31347> Adaptation> Channel "Comfort lighting - coming home switch-on event"> Adapt value

Coming home function automatically

STG 09> Access authorization: 31347> Adaptation> Channel "Comfort lighting - Coming Home installation status"> Set value to "automatic"

Discover Media / Pro - Current location in the header instead of the selected driving profile
From model year 2016 (MIB2), the coding leads to the deactivation of the MODE button and is therefore useless there.

STG 5F> Adaptation> ...

> Channel "Vehicle menu operation-menu_display_charisma"> set value to "not active"> Channel "Vehicle menu operation-
menu_display_charisma_clamp_15_off"> Set value to "not active"> Channel "Vehicle menu operation-menu_display_charisma_over_threshold_high">
value to "not active" set> channel "Vehicle menu operation-menu_display_charisma_standstill"> set value to "not active"> channel "Vehicle menu
operation-menu_display_charisma_after_disclaimer"> set value to "not active"

Discover Media / Pro - Activate off-road ads (MIB 2)

STG 5F> Adaptation> ...
© 2013-2021 Daniel Fuchs page 24
 > Channel "Car_Function_Adaptations_Gen2-menu_display_compass"> Set value to "active"> Channel "Car_Function_Adaptations_Gen2-
menu_display_compass_over_threshold_high"> Set value to "active"> Set channel "Car_Function_List_BAP_Gen2-compass_0x15"> to set value to "active"

Activate Discover Media / Pro online services (MIB 2)

Requires a software version> 200. After coding, the radio must be restarted (press and hold the power button for 10 seconds). The "Online Services" can then be
activated under Navigation> Settings.

STG 5F> Adaptation> ...

> Channel "Chargeable traffic information (TMC)"> Increase value by "32768"> Channel "Menu entries for mobile online services"> Set value to "activated">
Channel "Vehicle configuration-online_POI"> Set value to "on"> Channel "Vehicle configuration-online_navigation"> set value to "on"> channel "Vehicle
configuration-online_street_view"> set value to "on"

Discover Media / Pro - Activate WiFi streaming (MIB2)

STG 5F> Adaptation> Channel "WLAN"> Change value to "active"

Discover Media / Pro - Allow second phone via Bluetooth

STG 5F> Adaptation> Channel "Vehicle configuration Support_second_phone"> Change value to "on"

Discover Pro - change boot animation

STG 5F> Coding> Byte 18> Adjust the value as hexadecimal number accordingly

00 Highline

01 Hybrid

02 GTD

03 GTI

04 BlueMotion
© 2013-2021 Daniel Fuchs page 25
 05 E-golf

06 R-Line

07 R.

Activate Discover Pro - Green Menu

The adjustment must be made in the Engineer Session (4F).

STG 5F> Adaptation> Channel "Developer mode"> Set value to "activated"

Discover Pro - View speed limit from map data

Activate STG 5F> Coding> Byte 24> Bit 6

This coding only makes sense if traffic sign recognition (VZE) is not installed. The "Show traffic signs" setting must be activated in the map settings.

Discover Pro - Deactivate radio modulation AM

Activate STG 5F> Coding> Byte 14> Bit 1

Discover Pro - Change skin

STG 05> Coding> Byte 17> Adjust the value as a hexadecimal number accordingly

01 Highline

02 GTI / GTD / R

© 2013-2021 Daniel Fuchs page 26

Discover Pro - Activate WiFi streaming (MIB 1)
STG 5F> Coding> ...

> Activate byte 15> bit 4

> Activate byte 24> bit 3

STG 5F> Adaptation> ...

> Channel "WLAN"> Set value to "active"> Channel "Vehicle configuration-WIFI_Hotspot"> Set value to "active"> Channel "Vehicle configuration-UPnP"> Set
value to "active"

Third brake light as a receipt for the central locking

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Dynamic flashing modes-ZV_Blinken_zu"> Set value to "active"> Channel "Dynamic flashing modes-ZV_Blinken_auf"> Set value to "active">
Channel "Lamp22BR MA57 light function B 22"> Value to "Active flashing function has a 1 assigned bit set in pa_dynamisch_blinken "

Third brake light active when the tailgate is open

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Lamp22BR MA57 light function C 22"> Set value to "Rear lid open"> Channel "Lamp22BR MA57 dimming value CD 22"> Set value to "100"

The third brake light flashes when the hazard warning lights are active
STG 09> Access authorization 31347> Adaptation> ...

> Channel "Dynamic Blinkmodi-Warnblinken_Zuendung_EIN"> Set value to "active"> Channel "Dynamic Blinkmodi-Warnblinken_Zuendung_AUS"> Set value
to "Active"> Channel "Leucht22BR MA57-Lichtfunktion B 22"> Value to "Active blinking function has a 1 set assigned bit in pa_dynamisch_blinken ">
channel" lamp22BR MA57 light function C 22 "> set value to" flashing left dark phase "> channel" lamp22BR MA57 light function D 22 "> set value to"
flashing right dark phase "> channel" lamp22BR MA57- Dimming Direction CD 22 "> set value to" minimize "> channel" lamp22BR MA57 light function E 22
"> set value to" brake light "> channel"Luminaire 22BR MA57 dimming value EF 22 "> set value to" 100 "

© 2013-2021 Daniel Fuchs page 27

DWA - activation / activation (retrofitting)
These instructions apply to vehicles with coding in the BCM. These include most of the models introduced by 2015.

STG 09> Coding> ...

> Byte 11> activate bit 7> byte 12> activate bit 0, 4, 5 and 7

DWA - activation of the horn acknowledgment when locking and unlocking the vehicle
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Feedback signals - Acoustic feedback unlock"> Set value to "Yes"> Channel "Feedback signals - Lock acoustic feedback"> Set value to "Yes">
Channel "Feedback signals - menu control acoustic feedback"> Set value to "active"> Channel "Feedback signals-acoustic feedback global"> set value to
"active"> channel "feedback signals-acoustic feedback horn"> set value to "active"

as needed, too

> Channel "Feedback signals - duration of acoustic feedback from single horn"> Set value to "normal" or "short"

DWA - start of the alarm with mechanical opening (Thatcham)

Activate STG 09> Coding> Byte 12> Bit 6

Dynamic high beam (DLA) - activation (until MY 2016)

STG 09> Coding> Byte 02> Bit 0-2 set to "06 Extended_Fernlichtsteuerung, AFS: FLA: Fernlicht (GLW: MDF)"

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Fernlicht_Assistent-Assistenzfahrlicht: Sensitivity adjustable via BAP"> Change value to "available"
> Channel "Fernlicht_Assistent - menu control high beam assistant"> Change value to "available"
> Channel "Fernlicht_Assistent menu control high beam assistant factory setting"> Change value to "available"

STG A5> Coding>…

© 2013-2021 Daniel Fuchs page 28

 > Byte 19> set bit 0-3 to "00 additional high beam not installed"> byte 19> bit 4-7 to "30 headlight version (for FLA): LED with variable light distribution" set>
byte 21> bit 5-7 Set "40 Dynamic Light Assistant (DLA)"

STG 55> Coding> Byte 04> Activate bit 6 ("Masked permanent driving light (MDF) active / enabled")

Dynamic high beam (DLA) - activation (from MY 2017)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Fernlicht_Assistent-Extended high beam control"> Change the value to "AFS: FLA: High beam (GLW: MDF)"
> Channel "Fernlicht_Assistent-Assistenzfahrlicht: Sensitivity adjustable via BAP"> Change value to "available"
> Channel "Fernlicht_Assistent - menu control high beam assistant"> Change value to "available"
> Channel "Fernlicht_Assistent menu control high beam assistant factory setting"> Change value to "available"

STG A5> Coding>…

> Byte 19> set bit 0-3 to "00 additional high beam not installed"> byte 19> bit 4-7 to "30 headlight version (for FLA): LED with variable light distribution" set>
byte 21> bit 5-7 Set "40 Dynamic Light Assistant (DLA)"

STG 4B> Coding> ...

> Byte 10> Activate bit 6 ("Masked permanent driving light (MDF) active / enabled")> Byte 10> Activate bit 7 ("Sliding headlight range control (GLW) active /
enabled")> Byte 08> Activate bit 1 (if there is an error in the MFA occurs)> byte 09> activate bit 4 (if error occurs in MFA)

After completing the coding, a basic setting of the headlights must be carried out.

Parking aid - change cut-out speed

STG 10> Adaptation> Channel "Cut-off speed for parking aid"> Set value in km / h (factory setting: 15 km / h; value range: 1 to 15)

Parking aid - deactivate activation tone

STG 10> Adaptation> Channel "Activation tone for parking aid"> Set value to "Deactivated"

© 2013-2021 Daniel Fuchs page 29

Parking aid - deactivate audio lowering
STG 10> Adaptation> Channel "Audio lowering request"> Set value to "deactivated"

Parking aid - automatic activation when driving slowly forward

STG 10> access authorization: 71679> coding> byte 03> bit 4 activate

Parking aid - adjust curb distance (trigger continuous tone / last step)
STG 10> Adaptation> Channel "Distance to curb"> Adapt value in cm (factory setting: 15)

Parking aid - activate display, despite small parking aid (Leon III 5F, Audi A3 8V)
STG 10> Access authorization: 71679> Coding> Byte 02> Activate bit 0 ("Visual display of parking aid (OPS) active")

Parking aid - activate / deactivate guide lines

STG 10> Access authorization: 71679> Coding> Byte 01> Bit 5 (de) activate ("Vehicle Path Display active / enabled")

Parking aid - adjust volume front / rear

STG 10> Adaptation> ...

> Channel "Loudspeaker volume for front parking aid"> Adjust value accordingly (factory setting: 3)> Channel "Loudspeaker volume for rear parking aid">
Adjust value accordingly (factory setting: 6)

Parking aid - adjust pitch front / rear

STG 10> Adaptation> ...

> Channel "Loudspeaker frequency for front parking aid"> Adjust value accordingly (factory setting: 6)> Channel "Loudspeaker frequency for rear parking
aid"> Adjust value accordingly (factory setting: 3)
© 2013-2021 Daniel Fuchs page 30
Electronic parking brake (EPB) - deactivation of the automatic activation when the seat belt is removed
STG 03> Access authorization: 37202> Adaptation> Channel "Belt buckle query"> Set value to "not active"

ESP - change available modes (ASR off / ESC Sport / ESC off)
STG 03> Coding> Byte 29> Adjust the value as a hexadecimal number accordingly

?6 ESC on / ESC Sport / ESC off

?7 ESC on / ASR off / ESC off

?9 ESC on / ASR off / ESP Sport

Activate driving school mode (display of speed and indicators on the radio, only possible with Composition Color / Touch and Discover Media)
STG 5F> Adaptation> ...

> Channel "Vehicle function list CAN-driving school"> Set value to "Available"> Channel "Vehicle menu operation-menu_display_driving_school"> Set value
to "activated"> Channel "Vehicle menu operation-menu_display_driving_school_over_threshold_high"> Set value to "activated"

Window operation - do not cancel the release run-on when opening the door
STG 09> Access authorization: 31347> Adaptation> Channel "Cancel access control 2-release lag FH when opening the door"> Set value to "not active"

High beam assistant (Light Assist / HBA) - activation (variant 1)

Multi-function camera (control unit A5 - "MQB_MFK" - part number starts with 5Q0) must be installed, e.g. E.g. when ordering with Lane Assist and / or VZE
installed! After coding, the bus should be quiet.

STG 09> Access authorization: 31347> Adaptation> Channel "Assist light functions menu control high beam assistant"> Set value to "available"

STG 09> Coding> Byte 02> Bit 0-2 set to "03 Bi-Xenon headlights with Light Assist"

STG A5> Coding> Byte 02> Bit 0-7 set to "01 coding_Light_Assist High_Beam_Assist"
© 2013-2021 Daniel Fuchs page 31
High beam assistant (Light Assist / HBA) - activation (variant 2)
Multifunction camera (control unit A5 - "MQB_B_MFK"- Part number starts with 3Q0) must be installed, e.g. E.g. when ordering with Lane Assist and / or VZE
installed! After coding, the bus should be quiet. For the "Extended high beam control" channel, the correct value must be selected in accordance with the
previous configuration: If the high beam is controlled via AFS, this must also be selected in the new value. The existing value is only extended by the "FLA".

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Fernlicht_Assistent-Menu control high-beam assistant"> Set value to "available"> Channel "Fernlicht_Assistent-Menu control high-beam
assistant factory setting"> Set value to "available"> Channel "Fernlicht_Assistent-Extended_Fernlichtsteuerung"> Value to "AFS: FLA: BCM high beam" or
"AFS: FLA: high beam over AFS" set

Set STG A5> Coding> Byte 21> Bit 5-7 to "20 AFS_coding_Light_Assist, High_Beam_Assist"

High beam assistant (Light Assist) - adjust switch-on and switch-off times
STG A5> Access authorization: 20103> Adaptation> ...

> Channel "Activation speed for high beam assistant"> Adjust value in km / h (factory setting: 57)> Channel "Speed threshold for high beam
recommendation"> Adjust value in km / h (factory setting: 27)

High beam assistant (Light Assist) - Deactivate reset

STG 09> Access authorization: 31347> Adaptation> Channel "Assist light functions-high beam assistant reset"> Set value to "not active" (factory setting: active;
thus the FLA is deactivated again every time the ignition is switched off)

High beam assistant (Light Assist) - Deactivate city recognition

STG A5> Access authorization: 20103> Adaptation> Channel "Main_Beam_Assist_Urban_Area_Detection"> Change value to "not active"

Recalibrate the front / apron camera after lowering

STG A5> Access authorization: 20103> Adaptation> ...

© 2013-2021 Daniel Fuchs page 32

 > Channel "Body height, front left wheel arch edge"> Correct the value> Channel "Body height, wheel arch edge, front right"> Correct the value> Channel
"Body height, rear wheel arch edge, rear left"> Correct value> Channel "Body height, wheel arch edge, rear right"> Correct the value

Front Assist - advance warning - activate early / medium / late selection

An ACC control unit with part number 3Q0 or 2Q0 is required.

STG 13> Coding> Byte 11> Deactivate bit 3 ("adjustability_awv_pre_warning")

Front Assist - advance warning - save selected value

An ACC control unit with part number 3Q0 or 2Q0 is required.

STG 13> Coding> Byte 11> Activate bit 4 ("default_value_awv_pre_warning")

Windshield wipers - Park when the hood is opened

STG 09> Access authorization: 31347> Adaptation> Channel "Park windscreen wiper-wiper when opening the bonnet"> Set value to "active"

Windshield wipers - park when ignition is switched off (Octavia III 5E)
STG 09> Coding> Wiper (WWS)> Byte 01> Bit 4 deactivate

Front windscreen wiper - bring to service position via menu (Audi A3 8V)
STG 09> Access authorization: 31347> Adaptation> Channel "Front wiper menu control front wiper"> Set value to "active"

STG 5F> Adaptation> ...

> Channel "Vehicle function list BAP-wiper_comfort_0x0C"> Set value to "activated"> Channel "Vehicle menu operation-menu_display_wiper"> Set value to
"activated"> Channel "Vehicle menu operation-menu_display_wiper_over_threshold_high"> Set value to "activated"

© 2013-2021 Daniel Fuchs page 33

Windshield wiper - activate tear wiping
STG 09> Access authorization: 31347> Adaptation> Channel "Windshield wiper-tear wiping front status"> Change value to "active"

Front wiper - adjust wipe cycles per minute

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Wiping speed - continuous wiping level 1 cycles per minute"> Adjust value (factory setting: 40)> Channel "Wiping speed - continuous wiping level
2 cycles per minute"> Adjust value (factory setting: 60)> Channel "Wiping speed - reduced wiping speed, cycles per minute" "> Adjust value (factory setting:
30)

Front windscreen wiper - Activate front tear wiping

Activate STG 09> Coding> WWS> Byte 02> Bit 5

STG 09> Access authorization: 31347> Adaptation> Channel "Windshield wiper-tear wiping front status"> Set value to "active"

Windows release after-run after ignition off

STG 09> Access authorization: 31347> Adaptation> Channel "Access control 2-FH SAD Kl15Off release time"> Adapt value (factory setting: 600 s)

Footwell lighting - activation / activation (retrofitting)

STG 09> Coding> ...

> Byte 05> activate bit 7> byte 17> activate bit 3

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior lighting menu control ambient lighting effect lighting"> Change value to "active"> Channel "Lamp30FR LC72 load type 30"> Value to "36 -
LED low power" (for LED) or "18 - 2 * 5W" (for incandescent lamps) Change> Channel "Lamp30FR LC72 light function A 30"> Change value to "Footwell
light"> Channel "Lamp30FR LC72 dimming value AB 30"> Change value to "100"

© 2013-2021 Daniel Fuchs page 34

Footwell lighting - activation / activation multicolored (retrofitting)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "ambient_lighting_lin_slaves_modules-pa_verbauinfo_slave_14"> change the value to "built in"> Channel "ambient_lighting_lin_slaves_groups-
pa_verbauinfo_gruppe_14"> change the value to "3_not_defined"> change the channel "luminaire30FR LC72 load type 30"> change the value to "general
LED to" 12W " Lamp30FR LC72 light function A 30 "> change value to" footwell light "> channel" Lamp30FR LC72 dimming value AB 30 "> change value to"
127 "

Footwell lighting - activate the ambient lighting function (Audi)

After coding

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior light, luminaire configuration - footwell lighting"> Change value to "Built-in"> Channel "Interior light 2nd generation default value,
ambience profile footwell"> Change value to "20%"

Footwell lighting - conversion to LED - prevent error messages in the BCM

STG 09> Access authorization: 31347> Adaptation> Channel "Lamp30FR LC72 load type 30"> Set value to "32 - general LED up to 12W" (factory setting: 18 - 2 *
5W)

Deactivate the yellow mode switch light

With this coding, the switch for the travel profile selection remains in the basic color in every mode and does not change to yellow.

Activate STG 09> Coding> Byte 15> Bit 7

Activate trailer stabilization

STG 03> Adaptation> Channel "trailer stabilization"> Set value to "activated"

© 2013-2021 Daniel Fuchs page 35

Deactivate gearbox freewheel
Deactivate STG 19> Coding> Byte 12> Bit 2

Tailgate (electric) - can be opened / closed while driving

STG 6D> Access authorization: 12345> Adaptation> Channel "Speed threshold for" vehicle is moving "> Adapt value in km / h (factory setting: 6)

Tailgate (electric) - opening / closing when towing a trailer

STG 6D> Access authorization: 12345> Adaptation> Channel "Open when trailer is detected"> Value on "activated" (factory setting: not activated)

Tailgate (electric) - open / close via button in the center console and FFB
STG 6D> Access authorization: 12345> Adaptation> ...

> Channel "Control via switch for tailgate remote unlocking - tap function when closing"> Set value to "active"> Channel "Control via button for tailgate
opening remote control key tip function when closing"> Set value to "active"

or

> Channel "Control via switch for trunk lid remote unlocking button function when closing"> Set value to "active"> Channel "Control via button for trunk lid
opening remote control key button function when closing"> Set value to "active"

The push button function is the long press of the button, while the tap function is the short press.

Tailgate (electric) - change opening height

STG 6D> Access authorization: 12345> Adaptation> Channel "Program opening stop"> Adapt value

Tailgate (electric) - monitoring of keys in the trunk (KESSY)

STG 6D> Access authorization: 12345> Adaptation> ...

© 2013-2021 Daniel Fuchs page 36

 > Channel "Monitoring for key in trunk"> Set value to "active"> Channel "Warning tone for key in trunk"> Set value to "active"> Channel "Behavior with key
in trunk while closing"> Set value to "open"

Tailgate (electric) - Do not cancel closing when leaving the immediate area
STG 6D> Access authorization: 12345> Adaptation> Channel "Close with FFB, end when leaving close range"> Adapt value

Tailgate (electric) - allow closing with the key from a greater distance
STG 09> Access authorization: 31347> Adaptation> Channel "Convert top operation range limitation for servo rear close"> Set value to "not active"

Tailgate (electric) - adjust or deactivate warning signals

STG 6D> Access authorization: 12345> Adaptation> ...

> Channel "Pitch of acoustic warning"> Adjust value in Hz as required (factory setting: 1000)> Channel "Volume of acoustic warning"> Adjust value to "not
activated" (factory setting: activated)

and or

> Set the "Warning signal when closing with button in the interior or via radio key"> value "not activated"> Set channel "Warning signal when opening with
button in the interior or via radio key"> value "not activated"

Close tailgate with a time delay after individual opening (30 sec)
STG 09> Access authorization: 31347> Adaptation> Channel "Access control release lag rear after individual opening via HDF radio button"> Set value to
"active" (factory setting: not active)

Tailgate lights stay on when the flap is opened (Golf 7 AU, Audi A3 8V)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light27NSL RC6 light control HD AB 27"> Change value to "Always" (factory setting: only_if_closed)> Channel "Light26NSL LA72 light control HD
AB 26"> Change value to "Always" (factory setting: only_if_closed)
© 2013-2021 Daniel Fuchs page 37
Rear window heating - adjust heating time
STG 09> Access authorization: 31347> Adaptation> Channel "Window heating / rear window heating time value"> Adapt value in seconds (factory setting: 600)

Deactivate the rear wiper

STG 09> Coding> Byte 13> Deactivate bit 2

Deactivate STG 16> coding> byte 00> bit 2

Rear wiper - activate automatically when the front wiper is active at level 2 or higher
STG 09> Access authorization: 31347> Adaptation> Channel "Rear window wiper - automatic rear wiping"> Change value to "active"

Rear wiper - deactivate automatic wiping when reverse gear is engaged

STG 09> Access authorization: 31347> Adaptation> Channel "Rear window wiper comfort wipe rear"> Change value to "not active"

Rear wiper - activate tear wiping

STG 09> Access authorization: 31347> Adaptation> Channel "Rear window wiper - Tear wiping rear"> Change value to "active"

Rear wiper - adjust the wiper interval

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Rear window wiper comfort wipe rear interval pause time level interval)"> Adjust value (factory setting: 7, maximum: 14)> Channel "Rear
window wiper comfort wipe rear interval pause time level automatic)"> Adjust value (factory setting: 7, maximum: 14)

Move the HUD display horizontally

STG 82> Adaptation> Channel "Image shift-Horizontal shift"> Adapt value (positive = further to the right, negative = further to the left)

© 2013-2021 Daniel Fuchs page 38

Move the HUD display vertically
STG 82> Adaptation> Channel "Image shift - Vertical shift"> Adapt value (positive = higher, negative = lower)

Infotainment - activate Apple Wireless Carplay (Audi)

In principle, Carplay must be available for activation. In addition, the infotainment system must have a WLAN function.

STF 5F> Adaptation> ...

> Channel "Vehicle configuration-Apple_DIO_Wireless"> Change value to "on"> Channel "Vehicle configuration-wlan_5ghz_switch"> Change value to
"activated"

Infotainment - remove or activate the ejection lock

STG 5F> Adaptation> Channel "Eject lock" / "Button for CD return"> Change value to accordingly

Infotainment - activate the welcome sound (Audi)

STG 5F> Adaptation> Channel "Fahrzeugkonfiguration-vehicle_readiness_sound"> Change value to "activated"

License plate lighting - conversion to LED

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire25KZL HA59 load type 25"> Change value to "43 - general LED"> Channel "Luminaire25KZL HA59 dimming value AB 25"> Change value
to "127"

KESSY - automatic locking when the doors are closed (3Q0 control unit)
If the adaptation channel is not available, it should be left out.

Activate STG 05> Coding> Byte 02> Bit 5

STG 05> Adaptation> Channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock"> Set value to "active"

© 2013-2021 Daniel Fuchs page 39
KESSY - automatic locking when closing the doors (5Q0 control unit)
The automatic mirror folding does not work in this way. The fuel filler flap is also not locked. If the adaptation channel is not available, it should be left out.

Activate STG 05> Coding> Byte 02> Bit 4

STG 05> Adaptation> Channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock"> Set value to "active"

KESSY - Activate the staging / pulsing of the start button

STG 05> Adaptation> ...

> Channel "DeveloperCoding: Search lights-ZAT_illumination_concept_mybeat_clamp58xt"> Change value to "activated"> Channel "DeveloperCoding:
Search lights-ZAT_illumination_modus_mybeat_clamp58xt"> Change value to "activated"

Activate KESSY - convenience opening

Both door sensors (opening & closing) must be held at the same time to enable convenient opening via KESSY.

STG 09> Access authorization: 31347> Adaptation> Channel "Open access control 2-Kessy comfort"> Change value to "active"

KESSY - Temporary deactivation - activation (3Q0 control unit)

The KESSY control unit with at least index G (SW 0906) is required for this coding. If the software version is too old, the control unit can use VCP or similar.
updated. If an update is necessary, all adjustments to the control unit must be saved beforehand and imported again after the flash. The channels "Control unit
tailgate opening: sender 2: control parameters" and "Control unit tailgate opening: vehicle type" are particularly important.

STG 05> Adaptation> ...

> Channel "internal_passive_entry_exit_byte2-lf_shutdown"> set value to "activated"> channel "lf_shutdown_timeout_2nd_operation"> set value to "5" (or
desired timeout)

© 2013-2021 Daniel Fuchs page 40

KESSY - Temporary deactivation - activation (5Q0 control unit)
The KESSY control unit with at least index C (SW 0803) is required for this coding. If the software version is too old, the control unit can use VCP or similar.
updated.

STG 05> Adaptation> ...

> Channel "DeveloperCoding: Passive Entry Exit (Byte 2) -lf_shutdown"> Set value to "activated"> Channel "lf_shutdown_timeout_2nd_operation"> Set
value to "5" (or desired timeout)

Deactivate KESSY door sensors

STG 05> Coding> Byte 00> Deactivate bit 0 and 1

KESSY - Activate locking via Easy Close (3Q0 control unit)

After this coding, it is possible to lock the vehicle using the Easy Close. Closing with the door sensor is then not necessary separately.

STG 05> Adaptation> Channel "Byte9_VIP-Coding_easyclose_locking"> Set value to "activated"

Air conditioning - Air Care - activation

The prerequisite is that the hypoallergenic cabin air filter (5Q0819669) has been installed. The climate control unit requires at least SW 1401 (carry out an
update if necessary) and an MIB2 infotainment system must be installed. The gateway requires at least SW 1244 or 2244.

STG 08> coding> byte 15> activate bit 5 ("filtering circulating air")

Air Conditioning - Air Care - Save State

STG 08> Adaptation> Channel "Indoor air filtering: save"> Set value to "active"

Air conditioning - adjust the sensitivity of the indoor humidity sensor

STG 08> Coding> Byte 14> Bit 2-3 adapt

© 2013-2021 Daniel Fuchs page 41

Air conditioning - adjust blower logic in AUTO mode
STG 08> Coding> Byte 14> Bit 4-5 set to "00" or "10"

"00 fan logic with manual adjustment, manual offset" > The adjustment reduces / extends the current level, AUTO mode remains active
"10 blower logic with manual adjustment, blower level: absolute" > The adjustment sets the new level and deactivates the AUTO mode

Air conditioning - show blower level also in AUTO mode (not Audi A3 8V)
Set STG 08> Coding> Byte 11> Bit 6-7 to "40 Fan display in auto mode, activated"

Air conditioning - change the brightness of the LCD temperature display

STG 08> Adaptation> Channels "dimming_characteristics_2 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value or recreate the curve.

Air conditioning - brightness LEDs for current fan level

STG 08> Adaptation> Channels "dimming_characteristics_3 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value or recreate the curve.

Air conditioning - brightness LEDs for seat heating

STG 08> Adaptation> Channels "dimming_characteristics_4 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value or recreate the curve.

Air conditioning - brightness LEDs (rest)

STG 08> Adaptation> Channels "dimming_characteristics_5 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value or recreate the curve

© 2013-2021 Daniel Fuchs page 42

Air conditioning - Activate offset logic for the fan speed
The change means that manual adjustment of the blower level continues to operate in auto mode. Before that, the set level remains permanently active. This
applies until the "AUTO" button is pressed again.

STG 08> Adaptation> Channel "Fan logic for manual adjustment"> Set value to "Offset manual"

Combination instrument - deactivate seat belt reminder

STG 17> Adaptation> Channel "Deactivate seat belt warning"> Change value to "Yes"

or

Deactivate STG 17> Coding> Byte 00> Bit 2

Instrument cluster - change reserve tank volume

STG 17> Adaptation> Channel "defuel_threshold"> Adapt value in liters as desired

Combination instrument - scale lighting also active with parking lights

STG 17> Access authorization: 25327> Adaptation> Channel "Illumination_algorithm-Scale_switching_algorithm"> Set value to "lds" (factory setting:
parking_light)

Instrument cluster - change skin

STG 17> Adaptation> Channel "Display representation"> Adapt value

Combination instrument - change scale display (VC / AID / FPK)

STG 17> Adaptation> "Tube display" channel> Adapt value

© 2013-2021 Daniel Fuchs page 43

Combination instrument - adjust speedometer maximum (VC / AID / FPK)
STG 17> Adaptation> Channel "Tachometer end value"> Adapt value

Combination instrument - activate pointer test (staging)

STG 17> coding> byte 01> activate bit 0 ("pointer swipe active")

Combination instrument - ignition active Adapt / deactivate message

STG 17> Adaptation> Channel "Ignition active message; Trigger"> Adapt value accordingly

"no display" > Warning message deactivated

"Drivers door" > Warning message when the driver's door is opened
"all doors" > Warning message if any door is opened

Comfort actions via FFB even while the ignition is on / engine is running
STG 09> Access authorization: 31347> Adaptation> Channel "Access control radio at terminal 15 on"> Set value to "active"

Comfort flashing Change the flashing cycle

STG 09> Access authorization: 31347> Adaptation> Channel "Blinker control - comfort blinking blinking cycles"> Set value (range of values: 1-5)

Afterwards, the factory settings may have to be restored via the CAR menu, only then will the changed flashing cycle work!

Deactivate convenience flashing

STG 09> Access authorization: 31347> Adaptation> Channel "Flasher control - comfort flashing"> Set value to "not active"

Change the steering characteristic without selecting a driving profile

STG 44> Access authorization: 19249> Adaptation> Channel "Characteristic curves of steering assistance"> Change value accordingly
© 2013-2021 Daniel Fuchs page 44
Steering wheel heating - automatic activation
The function can then be activated / deactivated via the climate menu.

STG 08> Coding> Byte 13> Bit 2-3 set to "08 Steering wheel heating auto mode, outside temperature"

Adjust steering assistance

The adaptation only remains active until the next ignition change.

STG 44> Access authorization: 19249> Adaptation> "Steering assistance" channel> Adapt value (100%, 80%, 60%, 40% or 20%)

Adjust steering assistance directly when changing driving profiles (instead of incremental changes)
STG 44> Access authorization: 28183> Adaptation> Channel "Driving profile switchover"> Change value to "Direct" (factory setting: step-by-step: controlled by
time)

Adjust light switch-on threshold (Leon III 5F)

See also section "Assist light function - change light sensor sensitivity"

STG 09> Coding> RLS> Byte 00> Adapt bit 3-5 ("light switch-on threshold")

Headlight flasher also activates fog lights

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire12NL LB45 light function C 12"> Change value to "General flasher"> Channel "Luminaire12NL LB45 dimming value CD 12"> Change
value to "127"> Channel "Luminaire13NL RB5 light function C 13"> value to "Flasher generally "change> channel" luminaire13NL RB5 dimming value CD 13
"> change value to" 127 "

and if desired

> Channel "Light12NL LB45 light function D 12"> Change value to "Left high beam"> Channel "Light13NL RB5 light function D 13"> Change value to "Right
high beam"

© 2013-2021 Daniel Fuchs page 45

Headlight flasher during the day via fog lights
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Lamp12NL LB45 light function E 12"> Set the value to "Headlight flasher when the low beam is not active and the permanent driving light" is not
active> Channel "Lamp12NL LB45 dimming value EF 12"> Set the value to "100"> Channel "Lamp13NL RB5 light function E 12 "> Set value to" Headlight
flasher when dipped beam is not active and permanent driving light "is not active> Channel" Light13NL RB5 dimming value EF 12 "> Set value to" 100 ">
Channel" Light6ABL LC5 light function B 6 "> Value to" Flasher at already active dipped headlights or already active permanent running lights "set> channel"
lamp7ABL RB1 light function B 7 "> set value to" headlight flasher with already active dipped headlights or already active permanent running lights "

with the Skoda Octavia III RS additionally

> Channel "Lamp8FL LB39 light function E 8"> Set value to "Headlight flasher when dipped beam is not active and permanent driving light" is not active>
Channel "Lamp8FL LB39 dimming value EF 8"> Set value to "100"> Channel "Lamp9FL RB2 light function E 9 "> Set the value to" Headlight flasher when the
low beam is not active and the permanent driving light is not active "> Channel" Light 9FL RB2 dimming value EF 9 "> Set the value to" 100 "

Headlight flasher possible with ignition off

STG 09> Access authorization: 31347> Adaptation> Channel "Headlights and parking light flasher possible with ignition off"> Set value to "active" (factory
setting: not active)

Light / rain sensor - activation / activation (retrofitting)

STG 09> Coding> ...

> Byte 06> set bit 0-1 to 02> byte 07> activate bit 5

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Comfort lighting - Coming Home installation status"> Set value to "Automatic"> Channel "Comfort lighting - menu control Coming Home factory
setting"> Set value to "Active"> Channel "Comfort lighting - menu setting Cominghome"> Set value to "30 s"
> Channel "Comfort lighting - Coming home lights"> Set value to "Low beam"> Channel "Comfort lighting - Coming home switch-on event"> Set value to
"Driver door"> Channel "Comfort lighting - brightness threshold infrared measurement"> Value to "12 lx "or" 3 "> Channel" Comfort lighting leaving home
installation status "> Set value to" released "> Channel" Comfort lighting menu control leaving home activation via BAP "> Set value to" active "> Channel"

© 2013-2021 Daniel Fuchs page 46

 Comfort lighting menu setting Leaving -home time via BAP "> set value to" 30 s "> channel" comfort lighting-brightness threshold forward measurement ">
value to" 46400 lx "or" 112 "set

The adjustments must be checked and, if necessary, adjusted to ensure proper functionality.

Light / rain sensor - activate rain closing

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Access control 2-rain closing_ein_off"> Change value to "active"> Channel "Access control 2-rain closing_art"> Change value to "Permanent">
Channel "Access control 2-menu control rain closing"> Change value to "active"

STG 09> Coding> RLFS> Byte 00> (Bit 1 and) Activate bit 2

The coding of bit 2 is not accepted, it works with bit 1. The coding for the »RLHS« is not known.

MFA - adjust display time for rear seat belt display

STG 17> Adaptation> Channel "time_parameter_display-hmi_t_FondGurt"> Adapt value in seconds

MFA - adjust display duration for service reminder

STG 17> Adaptation> Channel "time_parameter_display-hmi_t_NextServiceAnz_ms"> Adapt value in seconds

MFA - adjust display duration for warning messages

STG 17> Adaptation> Channel "time_parameter_display-hmi_t_NextWarning_ms"> Adapt value in seconds

MFA - briefly display travel profile when changing

Activate STG 19> Coding> Byte 08> Bit 4

© 2013-2021 Daniel Fuchs page 47

MFA - Deactivate the "Switch on dipped headlights" message
STG 09> Access authorization: 31347> Channel "Außenlicht_uebergreifend-Fahrlichtwarnung_Hinweis_Konfig"> Set value to "not active"

MFA compass at the bottom

Activate STG 17> Coding> Byte 09> Bit 3

MFA - Show the volume to be refilled

Activate STG 17> Coding> Byte 10> Bit 4

Value differs slightly from the real amount of fuel to be refueled. Display in the MFA takes place in 5 l steps!

MFA - show oil temperature

Activate STG 17> Coding> Byte 10> Bit 1

MFA - show lap counter / lap timer

Activate STG 17> Coding> Byte 01> Bit 3

MFA - show shift recommendation (Audi A3 8V)

STG 17> Coding> Byte 01> Activate bit 5 ("Switching recommendation (Economy) active")

MFA - warning when driving with a rear fog light

STG 09> Access authorization: 31347> Adaptation> Channel "Driving lights and parking lights / rear fog light warning speed"> Adapt value in km / h

At speeds above this value, a message is displayed in the MFA that the NSL should be switched off.

© 2013-2021 Daniel Fuchs page 48

MFA - warning when driving with active parking lights
STG 09> Access authorization: 31347> Adaptation> Channel "Driving lights and parking lights warning, driving with parking lights"> Change value to "active"

MFA - warning at speeds over 120 km / h

Activate STG 17> Coding> Byte 00> Bit 6

MFA - Adapt / deactivate warning notice danger of slippery sides

STG 17> Access authorization: 20103> Adaptation> ...

> Channel "outside_temperature-p_ice_warning_exit_temperature"> set value in ° C (factory setting: 6)> Channel "outside_temperature-
p_ice_warning_entry_temperature"> set value in ° C (factory setting: 4)

MFA - warning sign of danger of slipperiness resubmission after engine off

STG 17> Access authorization: 20103> Adaptation> Channel "outside_temperature-p_storage_time_engine_off"> Adapt value in minutes (factory setting: 180)

MFA - Display cylinder deactivation (ACT / COD)

STG 17> adaptation> channel "cylinder deactivation"> change value to "display" (factory setting: no display)

Adjust microphone sensitivity

STG 5F> Adaptation> "Microphone sensitivity" channel> Adapt value

Multifunction steering wheel - activation / activation (retrofitting) (Audi A3 8V)

STG 16> coding> byte 00> activate bit 1 (does not have to be - try it out)

STG 17> Coding> Byte 10> Bit 7

© 2013-2021 Daniel Fuchs page 49

STG 19> Coding> Byte 01> Bit 0

STG 5F> Adaptation> ...

> Channel "vehicle function list CAN-MFL"> set value to "available"> channel "vehicle function list BAP-MFL_0x0F"> set value to "activated"> channel
"vehicle function list BAP-MFL_Jocker_0x34"> set value to "activated"> channel "Vehicle menu operation-menu_display_MFL_jocker"> Set value to
"activated"> Channel "Vehicle menu operation-menu_display_MFL_jocker_over_treshold_high"> Set value to "activated"

Fog lights - activation / activation (retrofitting)

Activate STG 09> Coding> Byte 07> Bit 3

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire12NL LB45 load type 12"> Set value to "10 - general headlights"> Channel "Luminaire12NL LB45 lamp defect bit position 12"> Set value
to "38"> Channel "Luminaire12NL LB45 error location middle byte DTC-DFCC 12"> Set value to "22"> Channel "Luminaire12NL LB45 light function A 12"> Set
value to "Fog light left"> Channel "Luminaire12NL LB45 light function B 12"> Set value to "Left cornering light"> Channel "Luminaire12NL LB45 dimming
value AB 12 "> set value to" 100 "> channel" luminaire13NL RB5 load type 13 "> set value to" 10 - general headlights "> channel" luminaire13NL RB5 lamp
defect bit position 13 "> set value to" 42 ">Channel "Luminaire13NL RB5 error location middle byte DTC-DFCC 13"> set value to "23"> Channel
"luminaire13NL RB5 light function A 13"> set value to "fog light right"> channel "luminaire13NL RB5 light function B 13"> value set to "cornering light right">
channel "lamp13NL RB5 dimming value AB 13"> set value to "100"

Fog lights - activate cornering lights

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light12NL LB45 light function B 12"> Adjust value to "Left cornering light"> Channel "Light13NL RB5 light function B 13"> Adjust value to "Right
cornering light"> Channel "Static cornering light regulation"> desiredRegulation set

Fog lights - activate intersection light

STG 55> coding> ...

> Byte 05> activate bit 0 (predictive route data, enabled)> byte 05> activate bit 1 (junction light with route data, enabled)

© 2013-2021 Daniel Fuchs page 50

or

STG 4B> Coding> ...

> Byte 11> activate bit 0 (predictive route data enabled)> byte 11> activate bit 1 (junction light with route data enabled)

Fog lights - conversion to LED (Octavia III 5E)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire8FL LB39 load type 8"> Set value to "6 - LED light module"> Channel "Luminaire9FL RB2 load type 9"> Set value to "6 - LED light
module"> Channel "Luminaire12NL LB45 load type 12"> Set value to Set "6 - LED light module"> Channel "Luminaire13NL RB5 load type 13"> Set value to "6
- LED light module"

Rear fog lights - both active (Octavia III 5E)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Lamp26NSL LA72 light function A 26"> Adjust value to "Rear fog light if no trailer is attached"> Channel "Lamp26NSL LA72 dimming value AB
26"> Set value to "100" if not yet set> Channel "Lamp27NSL RC6 light function A 27 "> adjust value to" rear fog light if no trailer is plugged in "> channel"
lamp27NSL RC6 dimming value AB 27 "> set value to" 100 "if not yet set

Personalization - activation (variant 1)

This variant applies to vehicles with coding in the BCM. These include most of the models introduced by 2015. Control units that are not installed can simply be
left out.

STG 09> Coding> ...

> Byte 08> Activate bit 2 (Personalization profiles active)> Byte 11> Bit 4-6 to "10 Profil_Variante, Account (v. 1.x)"

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Personalization-Aktivierungsoption_im_HMI-Menue_sichtbar"> Adjust value to "active"> Channel "Personalization-Number_User accounts">

Adjust value to "4"> Channel "Personalization-User Account Management_in_HMI-Menue_visbar"> Adjust value to "active"> Channel "Personalization -
Personalisierung_aktiv "> Adjust value to" active "> Channel" Personalization-Personalization-Personalization_en_in_HMI-Menue_sichtbar "> Adjust value
© 2013-2021 Daniel Fuchs page 51
 to" active "> Channel" Personalization-PSO_FSG_Setup2_Bit_0 "> Adjust value to" active "> Channel" Personalization-PSO_FSG_Setup2_Bit_1 "> Value to
Adapt "active"> channel "Personalization-PSO_FSG_Setup2_Bit_2">Adjust value to "active"> Channel "Personalization-PSO_FSG_Setup2_Bit_3"> Adjust
value to "active"> Channel "Personalization-PSO_FSG_Setup2_Bit_4"> Adjust value to "active"> Channel "Personalization-PSO_FSG_Setup2_Bit_5"> Adjust
value to "active"> Channel "Personalization-PSO_FSG_Setup2_Bit_6"> adjust value to "active"> channel "Personalization-PSO_FSG_Setup2_Bit_7"> adjust
value to "active"adjust> channel "Personalization-PSO_FSG_Setup2_Bit_6"> adjust value to "active"> channel "Personalization-PSO_FSG_Setup2_Bit_7">
adjust value to "active"adjust> channel "Personalization-PSO_FSG_Setup2_Bit_6"> adjust value to "active"> channel "Personalization-
PSO_FSG_Setup2_Bit_7"> adjust value to "active"

Activate STG 17> Coding> Byte 10> Bit 0

Set STG 08> Coding> Byte 15> Bit 3-4 to "08 Personalization, activated"

Set STG 36> Coding> Byte 09> Bit 1-2 to "02 Func_key_memory_personalization, personalization active"

Personalization - activation (variant 2)

This variant applies to vehicles without coding in the BCM. These include most of the models that were introduced from 2015 or have received a facelift. Control
units that are not installed can simply be left out.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Personalization-Aktivierungsoption_im_HMI-Menue_sichtbar"> Adjust value to "active"> Channel "Personalization-Number_User accounts">

Adjust value to "4"> Channel "Personalization-User Account Management_in_HMI-Menue_visbar"> Adjust value to "active"> Channel "Personalization -
Personalisierung_aktiv "> Adjust value to" active "> Channel" Personalization-Personalization-Personalization_en_in_HMI-Menue_sichtbar "> Adjust value
to" active "> Channel" Personalization-Personalization_Profilfunkion "> Adjust value to" profiles_active "> Channel" Personalization-Profil_Variante "> Value
to Customize "Account (v. 1.x)"> Channel "Personalization-PSO_FSG_Setup2_Bit_1 "> Adjust value to" active "> Channel" Personalization-
PSO_FSG_Setup2_Bit_2 "> Adjust value to" active "> Channel" Personalization-PSO_FSG_Setup2_Bit_3 "> Adjust value to" active "(only if STG 36 is
installed)> Channel" Personalization -PSO_FSG_Setup2_Bit_4 "> Adjust value to" not active "

Activate STG 17> Coding> Byte 10> Bit 0

Set STG 08> Coding> Byte 15> Bit 3-4 to "08 Personalization, activated"

Set STG 36> Coding> Byte 09> Bit 1-2 to "02 Func_key_memory_personalization, personalization active"

STG A5> Coding> Byte 13> Bit 3-5 set to "10 Personalized_key, Version_1.x"

© 2013-2021 Daniel Fuchs page 52

Pace car flashing taillights (LED taillights) (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Lamp16BLK SLB35BLK SL KC9 light function A 16"> Adjust value to "Flashing left dark phase" (factory setting: light phase)> Channel "Lamp17TFL R
BLK SRB3TFL R BLK SR KC3 light function A 17"> Value to "Flashing right dark phase" adapt (factory setting: light phase)

Pace car flashing of the taillights (only when opening / closing the vehicle) (LED taillights) (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Dynamic flashing modes-ZV_Blinken_zu"> Set value to "active"> Channel "Dynamic flashing modes-ZV_Blinken_auf"> Set value to "active">
Channel "Lamp16BLK SLB35BLK SL KC9 light function C 16"> Value to "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"set>
channel" luminaire16BLK SLB35BLK SL KC9 dimming value CD 16 "> set value to" 100 "
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function E 16"> Set value to "Flashing right light phase"> Channel "Luminaire16BLK SLB35BLK SL KC9
dimming value EF 16"> Set value to "0"> Channel "Luminaire16BLK SLB35BLK SL KC9-Dimming Direction EF 16 "> set value to" minimize "> channel"
lamp17TFL R BLK SRB3TFL R BLK SR KC3 light function C 17 "> value to"Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"set>
channel" luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value CD 17 "> set value to" 100 "> channel" luminaire17TFL R BLK SRB3TFL R BLK SR KC3
light function E 17 "> set value to" flashing left light phase " > Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value EF 17"> Set value to "0">
Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3-Dimming Direction EF 17"> Set value to "minimize"

Pace car flashing of the rear lights (only with hazard warning lights) (LED rear lights) (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Dynamic Blinkmodi-Warnblinken_Zuendung_EIN"> Set value to "active"> Channel "Dynamic Blinkmodi-Warnblinken_Zuendung_AUS"> Set value
to "Active"> Channel "Leucht16BLK SLB35BLK SL KC9-Light function C 16"> Value to "Active flashing function has an assigned bit set to 1 in
pa_dynamisch_blinken"set> channel" luminaire16BLK SLB35BLK SL KC9 dimming value CD 16 "> set value to" 100 "> channel" luminaire16BLK SLB35BLK SL
KC9 light function E 16 "> set value to" flashing right light phase "> channel" luminaire16BLK SLB35BLK SL KC9- Dimming value EF 16 "> set value to" 0 ">
channel" lamp16BLK SLB35BLK SL KC9-Dimming Direction EF 16 "> set value to" minimize "> channel" lamp17TFL R BLK SRB3TFL R BLK SR KC3 light function
C 17 "> value on "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"set> channel" luminaire17TFL R BLK SRB3TFL R BLK SR KC3
dimming value CD 17 "> set value to" 100 "> channel" luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function E 17 "> set value to" flashing left light phase
" > Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value EF 17"> Set value to "0"> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3-
Dimming Direction EF 17"> Set value to "minimize"

© 2013-2021 Daniel Fuchs page 53

Parking light on both sides
Regardless of which position the steering column switch is set - except "0" - parking lights are active on both sides (compared to normal, only the corresponding
side)

STG 09> Access authorization: 31347> Adaptation> Channel "Driving light and parking light / parking light activated via LSS"> Change value to "both sides"
(factory setting: one-sided)

Radio receiver amplifier

STG 5F> Access authorization: 20103> Adaptation> ...

> Channel "Audio management input gain radio (FM)"> Adjust value to "127" (factory setting: -127)> Channel "Audio management input gain radio (AM)">
Adjust value to "127" (factory setting: -127) > Channel "Audio Management Input Gain Digital Radio (DAB)"> Adjust value to "127" (factory setting: -127)

Tire pressure control display (direct, TPMS) - activation / activation

Activate STG 19> installation list> "65 - tire pressure"

STG 03> Coding> ...

> Byte 27> deactivate bits 4, 5 and 6> deactivate byte 28> bit 7

STG 17> Coding> ...

> Byte 03> Activate bit 7 ("Tire pressure control, yes")> Byte 04> Deactivate bit 0 ("Tire control display, yes")> Byte 11> Activate bit 2 ("Tire pressure control:
BAP route, yes")

STG 5F> Adaptation> ...

> Channel "Vehicle function list BAP-tire_pressure_system_0x07"> Set value to "activated"> Channel "Vehicle function list BAP-
tire_pressure_system_0x07_msg_bus"> Set value to "Extended data bus"

STG 65> Access authorization: 20103

> Channel "Write sensor identification number - wheel position"> Set value to "Rear right"

© 2013-2021 Daniel Fuchs page 54

After the coding has been completed, parameters for the tire pressures must be generated and processed with VCP or similar. uploaded. To create the
parameters, theTPMS tool can be used by jolt.

Tire pressure control display (indirect, via ABS) - activation / activation (retrofitting)
STG 03> Coding> ...

> Byte 27> activate bit 5> activate byte 28> bit 7

STG 5F> Adaptation> ...

> Channel "Vehicle function list BAP-tire_pressure_system_0x07"> Set value to "active"> Channel "Vehicle function list BAP-
tire_pressure_system_0x07_msg_bus"> Set value to "Chassis data bus"> Channel "Vehicle menu operation-menu_display_rdk"> Set value to "active">
Channel " Vehicle menu operation-menu_display_rdk_over_treshold_high "> Set value to" active "

STG 17> Coding> Byte 04> Activate bit 0 ("Indirect tire pressure monitoring system (TPMS)")

Rear view camera (low) - activation / activation (retrofitting)

Activate STG 10> Coding> Byte 02> Bit 4

Activate STG 5F> Coding> Byte 19> Bit 4

Reversing camera (low) - Deactivate deactivation when the tailgate is open

STG 5F> Adaptation> Channel "Vehicle configuration-rvc_low_black_screen_trunk_open"> Set value to "not activated"

Reversing camera (low) - Switch off speed-dependent deactivation

STG 5F> Adaptation> Channel "Vehicle configuration-rvc_low_black_screen_velocity_threshold"> Set value to "not activated"

Increase reversing light luminosity (Golf 7 AU)

STG 09> Access authorization: 31347> Adaptation> ...
© 2013-2021 Daniel Fuchs page 55
 > Channel "Luminaire 28RFL LC11 dimming value AB 28"> Set value to "100" (factory setting: 86)
> Channel "Luminaire29RFL RA64 dimming value AB 29"> Set value to "100" (factory setting: 86)

Headlight cleaning - deactivate SWRA

STG 09> coding> byte 13> deactivate bit 0 ("head_lamp_wash")

Sunroof - make the opening position accessible directly from the sliding position
STG 09> Coding> Sunroof (J245 PS24.402)>…

> Byte 01> activate bit 1> byte 01> activate bit 2

Sunroof - Do not cancel the closing process when opening the door (with STG CA)
STG CA> Coding> Byte 00> Activate bit 6 ("Continue_closing_movement_without_BCM_FH_Freigabe")

Sunroof - Do not cancel the closing process when opening the door (without STG CA)
STG 09> Coding> Sunroof (J245 PS24.402)> Byte 00> Bit 7 activate

Sunroof - change mode when opening comfortably

STG 09> Access authorization: 31347> Adaptation> Channel "Access control 2-SAD direction comfort opening"> Change value to "open" (factory setting: tilting)

... if STG CA is installed, then additionally ...

STG CA> Adaptation> Channel "Comfort functions - target position for comfort opening"> Change value to "Sliding position" (factory setting: opening position)

Sunroof - decouple the roller blind from the roof (with STG CA)
Deactivate STG CA> Coding> Byte 02> Bit 6

© 2013-2021 Daniel Fuchs page 56

Sunroof - decouple the roller blind from the roof (without STG CA)
STG 09> Coding> Sunroof roller blind (J394 PS24.402)> Byte 00> Bit 0 deactivate

At the bottom of the list for Coming Home / Leaving Home

STG 09> Access authorization: 31347> Adaptation> Channel "Lamp27NSL RC6 light function B 27"> Adapt value to "Coming Home or Leaving Home active"

Tail light inside double function as brake light (for LED taillights) (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light27NSL RC6 light function C27"> Set value to "Brake light" (factory setting: not active)
> Channel "Luminaire27NSL RC6 dimming value CD27"> Set value to "100" (factory setting: 0)

Tail light inside double function as brake light (for halogen taillights) (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light23SL HLC10 light function C23"> Set value to "Brake light" (factory setting: not active)> Channel "Light23SL HLC10_Dimmwert CD23"> Set
value to "100" (factory setting: 0)> Channel "Light24SL HRA65 light function C24" > Set value to "Brake light" (factory setting: not active)> Channel
"Leucht24SL HRA65_Dimmwert CD24"> Set value to "100" (factory setting: 0)

Tail light inside Deactivate double function as brake light when the rear fog light is active (legal requirement according to StVZO)
STG 09> Access authorization: 31347> Adaptation>… (example for LED taillights)

> Channel "Light27NSL RC6 light function E 27"> Set value to "Rear fog light if no trailer is attached" (factory setting: not active)> Channel "Light27NSL RC6
dimming value EF 27"> Set value to "10" (factory setting: 0)> Channel "Leucht27NSL RC6-Dimming Direction EF 27"> Set value to "minimize" (factory setting:
maximize)

Seats - activate comfort entry "Easy Entry" (electric seats)

Activate STG 36> Coding> Byte 03> Bit 1
© 2013-2021 Daniel Fuchs page 57
Seats - Comfort entry "Easy Entry" activate menu item (electric seats)
STG 36> Coding> ...

> Byte 09> activate bit 6 (easy_entry_front_over_MMI)> byte 06> activate bit 4 (EasyEntry_Enable_Passenger_over_DriverMMI) (only execute if STG 06 is
installed)

STG 5F> Adaptation> ...

> Channel "Function_Adaptations_Gen2-menu_display_seat_configuration"> Set value to "activated"> Channel "Function_Adaptations_Gen2-

menu_display_seat_configuration_over_threshold_high"> Set value to "activated"

Seat heating - adjust the temperatures of the levels

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Allocation of the current consumption for seat heating stage / seat heating stage 1 lower switching threshold"> Adjust value in ° C> Channel
"Allocation of current consumption for seat heating stage / seat heating stage 1 upper switching threshold"> Adjust value in ° C> Channel "Allocation of
current consumption for seat heating stages -Seat heating stage 2 lower switching threshold "> Adjust value in ° C> Channel" Allocation of power
consumption for seat heating stage - seat heating stage 2 upper switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for
seat heating stage - seat heating stage 3 lower switching threshold "> Adjust value in ° C> Channel "Allocation of power consumption for seat heating stage -
seat heating stage 3 upper switching threshold"> Adjust value in ° C> Channel "Allocation of the current consumption for seat heating stage - seat heating
stage 4 lower switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage seat heating stage 4 upper
switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage - seat heating stage 5 lower switching
threshold "> adjust value in ° C> channel" Allocation of the current consumption for seat heating stage-seat heating stage 5 upper switching threshold ">
adjust value in ° C> channel" Allocation of current consumption for seat heating stage-seat heating stage 6 lower switching threshold "> value in ° Adjust C>
Channel "Allocation of power consumption for seat heating stage / seat heating stage 6 upper switching threshold"> Adjust value in ° CAdjust value in °
CAdjust value in ° CAdjust value in ° CAdjust value in ° CChannel "Allocation of the current consumption for seat heating stage - seat heating stage 4 upper
switching threshold"> Adjust value in ° C> Channel "Allocation of current consumption for seat heating stage seat heating stage 5 lower switching
threshold"> Adjust value in ° C> Channel "Allocation of current consumption for seat heating stage Seat heating stage 5 upper switching threshold "> Adjust
value in ° C> Channel" Allocation of power consumption for seat heating stage - seat heating stage 6 lower switching threshold "> Adjust value in ° C>
Channel" Allocation of current consumption for seat heating stage - seat heating stage 6 upper switching threshold "> Value adjust in ° CChannel "Allocation
of the current consumption for seat heating stage - seat heating stage 4 upper switching threshold"> Adjust value in ° C> Channel "Allocation of current
consumption for seat heating stage seat heating stage 5 lower switching threshold"> Adjust value in ° C> Channel "Allocation of current consumption for
seat heating stage Seat heating stage 5 upper switching threshold "> Adjust value in ° C> Channel" Allocation of power consumption for seat heating stage -
© 2013-2021 Daniel Fuchs page 58
 seat heating stage 6 lower switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage - seat heating stage
6 upper switching threshold "> Value adjust in ° CAllocation of the current consumption for seat heating stage / seat heating stage 5 lower switching
threshold "> Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage / seat heating stage 5 upper switching threshold ">
Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage / seat heating stage 6 lower switching threshold "> adjust value in °
C> channel" Assignment of power consumption for seat heating stage - seat heating stage 6 upper switching threshold "> adjust value in ° CAllocation of the
current consumption for seat heating stage / seat heating stage 5 lower switching threshold "> Adjust value in ° C> Channel" Allocation of current
consumption for seat heating stage / seat heating stage 5 upper switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for
seat heating stage / seat heating stage 6 lower switching threshold "> adjust value in ° C> channel" Assignment of power consumption for seat heating stage
- seat heating stage 6 upper switching threshold "> adjust value in ° CAllocation of the current consumption for seat heating stage / seat heating stage 6
lower switching threshold "> Adjust value in ° C> Channel" Allocation of current consumption for seat heating stage / seat heating stage 6 upper switching
threshold "> adjust value in ° CAllocation of the current consumption for seat heating stage / seat heating stage 6 lower switching threshold "> Adjust value
in ° C> Channel" Allocation of current consumption for seat heating stage / seat heating stage 6 upper switching threshold "> adjust value in ° C

Different levels are used depending on the vehicle. In the Octavia III and Golf 7, levels 1 and 2, 3 and 4 as well as 5 and 6 are each the same. With the Leon 5F,
only levels 2, 4 and 6 are occupied.

Seat heating - save the selected seat heating level

STG 08> Adaptation> ...

> Channel "Storage of the driver's seat heating level"> Set the value to "active" or "active for 10 minutes"
> Channel "Storage of the passenger seat heating level"> Set the value to "active" or "active for 10 minutes"

Seat heating - adjust withdrawal thresholds (Audi A3 8V)

STG 08> Adaptation> Channel "Time until seat heating reduction level X to level Y"> Adjust value in minutes (0 = function deactivated)

Set daylight saving time automatically

STG 5F> Adaptation> "Automatic daylight saving time" channel> Set value to "Europe" (factory setting: manual)

After coding has been successful, activate the checkmark next to “Set daylight saving time automatically” in the CAR menu under “Time and date”

© 2013-2021 Daniel Fuchs page 59

Deactivate the sound actuator or reduce the volume
STG A9> Adaptation> Channel "Volume of the actuator for structure-borne noise"> Adapt the value accordingly (factory setting: 100)

Sound system - expansion of the internal sound system (without external amp) with virtual surround and subwoofer
STG 5F> Coding> Byte 11> change to "04" (Sound_System_internal_individual)

Mirror - Activate lowering of the passenger side

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Access control 2-mirror lowering when driving backwards"> Set value to "active"> Channel "Access control 2-menu control mirror lowering"> Set
value to "active"

Activate STG 42> Coding> Byte 04> Bit 1, 2 and 3

Activate STG 52> Coding> Byte 04> Bit 2 and Bit 3

Mirror - folding - activation

STG 42> Coding> ...

> Byte 04> activate bit 4 ("Foldable Mirrors installed")> Byte 04> activate bit 6 ("Comfort Mirror Folding active")

STG 52> Coding> ...

> Byte 04> activate bit 4 ("Foldable Mirrors installed")> Byte 04> activate bit 6 ("Comfort Mirror Folding active")

Mirror - folding is also active while driving

STG 42> Coding> Byte 09> Activate bit 7 STG 52> Coding> Byte 09> Activate bit 7

© 2013-2021 Daniel Fuchs page 60

Adjust mirror folding in FFB mode
STG 09> Access authorization: 31347> Adaptation> Channel "Access control 2-radio mirror folding mode"

"by look command via remote control key" > Mirrors fold in immediately when locked via FFB
"convenience operation via remote control key" > Mirrors do not fold in until the lock button on the key is pressed for 2-3 seconds

Mirror heating automatically activated when the rear window heating is activated
STG 42> coding> byte 09> activate bit 2 ("rear_window_heater_trigger, active") STG 52> coding> byte 09> activate bit 2 ("rear_window_heater_trigger, active")

Mirror - heating permanently active when switched on once

After coding, the mirror heating is activated for the entire journey as soon as it has been activated briefly. Useful if you want to have the mirror heating active,
but at the same time want to use the lower passenger mirror.

STG 42> coding> byte 09> activate bit 1 ("mirror_heater_single_trigger, active") STG 52> coding> byte 09> activate bit 1 ("mirror_heater_single_trigger, active")

Mirror - Surrounding lighting is active when the mirrors are folded in

STG 42> coding> byte 01> deactivate bit 5 ("turn_off_front_field_light_with_folded_mirror, active") STG 52> coding> byte 01> deactivate bit 5
("turn_off_front_field_light_with_folded_mirror, active")

Spoiler - do not lower when locking the vehicle (Audi TT 8S)

STG 09> Access authorization: 31347> Adaptation> Channel "Additional functions spoiler Comfort lowering of the spoiler via lock cylinder FT"> Set value to
"active"

Spoiler - do not lower automatically after manual extension (Audi TT 8S)

STG 09> Access authorization: 31347> Adaptation> Channel "Additional functions spoiler entry suppression after manual extension"> Set value to "active"

© 2013-2021 Daniel Fuchs page 61

Activate voice control (Audi A3 8V)
This adjustment is often no longer possible because the function is now secured by SWaP.

Activate STG 5F> Coding> Byte 24> Bit 1

Lane Assist - activation (variant 1)

Multi-function camera (control unit A5 - "MQB_MFK" - part number starts with 5Q0) must be installed, e.g. For example installed when ordering with DLA and /
or VZE! After coding, the bus should be quiet.

STG A5> coding> byte 00> activate bit 0 ("Lane departure warning (HCA) active / installed")

STG A5> Access authorization: 20103> Adaptation> ...

> Channel "HCA_On_State"> Set value to "Menu"> Channel "HCA_Warning_Intensity"> Set value to "Menu"> Channel "BAP_Personalisierung"> Set value to
"not activated"> Channel "Time of intervention"> Value to "late (setting via Menu) "set> channel" personalization lane departure warning at terminal 15 on
"> set to" last setting "

STG 5F> Adaptation> ...

> Channel "Vehicle function list BAP; Extension_LDW_HCA_0x19"> Set value to "activated"> Channel "Vehicle function list BAP;
Extension_LDW_HCA_0x19_msg_bus"> Set value to "Data bus Extended"
> Channel "Vehicle menu operation-menu_display_Lane_Departure_Warning"> Set value to "activated"> Channel "Vehicle menu operation-
menu_display_Lane_Departure_Warning_over_threshold_high"> Set to "activated"

STG 17> Coding> ...

> Byte 04> Activate bit 6 ("Lane keeping assistant / Lane Assist installed")> Byte 11> Activate bit 1 ("Lane keeping assistant / Lane Assist Information (BAP)
installed / active")

STG 44> Access authorization: 19249> Coding> Byte 00> Activate bit 4 ("Lane departure warning system installed")

Lane Assist - activation (variant 2)

Multifunction camera (control unit A5 - "MQB_B_MFK" - part number starts with 3Q0) must be installed, e.g. For example installed when ordering with DLA and
/ or VZE! After coding, the bus should be quiet. Coding in STG 10 is only necessary if the corresponding bit is labeled as such or if errors remain in the STG.
© 2013-2021 Daniel Fuchs page 62
STG A5> coding> byte 16> activate bit 7 ("Lane departure warning system (HCA) active / installed [PR-7Y9]")

STG A5> Access authorization: 20103> Adaptation> ...

> Channel "Personalization time of intervention at terminal 15 on"> Set value to "Last setting"> Channel "Personalization BAP"> Set value to "not active">
Channel "Switch-on state of lane departure warning"> Value to "on (setting via menu)" set

STG 5F> Adaptation> ...

> Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19"> value to "enabled"> Set channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus">

value to "data Extended"> Set channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning"> value to "enabled"> Set channel
"Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning_over_threshold_high" > Set the value to "activated"

STG 17> Coding> ...

> Byte 04> Activate bit 6 ("Lane keeping assistant / Lane Assist installed")> Byte 11> Activate bit 1 ("Lane keeping assistant / Lane Assist Information (BAP)
installed / active")

STG 44> Access authorization: 19249> Coding> Byte 03> Bit 0 activate ("Lane departure warning system installed")

STG 10> Access authorization: 71679> Coding> Byte 03> Activate bit 5 ("Lane departure warning with steering assistance installed")

Lane Assist - activation (variant 3)

Multi-function camera (control unit A5 - "MQB MFK 3.0" - part number begins with 2Q0) must be installed, e.g. E.g. installed when ordering with DLA and / or
VZE.After coding, the bus should be quiet. Coding in STG 10 is only necessary if the corresponding bit is labeled as such or if errors remain in the STG.

STG A5> Coding>…

> Byte 08> set bit 5-7 to "A0 Point_of_intervention, late_setting_over_menu"> byte 09> set bit 0-1 to "03 Configuration_for_lane_departure_warning_Kl15,
Last_setting"> byte 09> bit 2-3 to "0C Lane_assist_system_mode, Selection_over_menu" set> byte 09> activate bit 7 ("HC, 0 = not_coded / 1 = coded")> byte
17> activate bit 0 ("Hc_messages, 0 = not_coded / 1 = coded")> byte 17> bit 1-3 to "02 HC_Warn_Intensity Set, Setting_over_Menu "> Byte 17> Bit 5-7 to"
20 Hc_variant, Variant_1 "or" 00 Hc_variant, Variant_0 "

STG A5> Access authorization: 20103> Adaptation> Channel "Switch-on status of lane departure warning system"> Set value to "on (setting via menu)"

STG 5F> Adaptation> ...

© 2013-2021 Daniel Fuchs page 63

 > Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19"> value to "enabled"> Set channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus">
value to "data Extended"> Set channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning"> value to "enabled"> Set channel
"Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning_over_threshold_high" > Set the value to "activated"

STG 17> Coding> ...

> Byte 04> Activate bit 6 ("Lane keeping assistant / Lane Assist installed")> Byte 11> Activate bit 1 ("Lane keeping assistant / Lane Assist Information (BAP)
installed / active")

STG 44> Access authorization: 19249> Coding> Byte 03> Bit 0 activate ("Lane departure warning system installed")

STG 10> Access authorization: 71679> Coding> Byte 03> Activate bit 5 ("Lane departure warning with steering assistance installed")

Lane departure warning - activate adaptive lane guidance via the steering column button
A front / in-front camera control unit with part number 3Q0 is required. After coding, the adaptive lane guidance can be switched on and off by holding down
the Lane button on the steering column.

STG A5> coding> byte 22> activate bit 7 ("HC_LONGPRESS")

Lane departure warning - deactivation threshold for driver inactivity

STG A5> Access authorization: 20103> Adaptation> Channel "Deactivation threshold of driver inactivity"> Adapt value (factory setting: medium)

Lane departure warning - Set the time of intervention via the menu
STG A5> Coding> Byte 14> Bit 5-7 set to "A0 Time of intervention: late (setting via menu)"

Lane departure warning - adjust the intensity of the steering wheel vibration
STG A5> Access authorization: 20103> Adaptation> Channel "Steering wheel vibration intensity"> Adapt value accordingly (factory setting: medium)

© 2013-2021 Daniel Fuchs page 64

Lane departure warning - adjust the intensity of the steering assistance
STG A5> Access authorization: 20103> Adaptation> Channel "Intensity steering wheel support"> Adapt value (factory setting: medium)

Lane departure warning - save the last switch-on status

A front / front camera control unit with part number 2Q0 is required.

STG A5> Coding> Byte 09> Bit 0-1 to "03 Configuration_for_lane_departure_warning_Kl15, Last_setting"

Lane departure warning - set warning strength via menu (variant 1)

A front / in-front camera control unit with part number 5Q0 is required.

STG A5> Access authorization: 20103> Adaptation> Channel "HCA_Warning_Intensity"> Set value to "Menu"

respectively.

STG A5> Access authorization: 20103> Adaptation> Channel "Warning intensity lane departure warning"> Set value to "Selection via menu"

Lane departure warning - set warning strength via menu (variant 2)

A front / in-front camera control unit with part number 3Q0 is required.

STG A5> Coding> Byte 13> Bit 1-2 to "06 System mode lane departure warning, selection via menu"

Auxiliary heating - adjust the post-heating time

STG 08> Adaptation> Channel "Post-heating time of auxiliary heating"> Adapt value in minutes (factory setting: 10)

Auxiliary heating - adjust the temperature for activating the interior fan
STG 18> Access authorization: 80782> Adaptation> Channel "Control parameter parking heater temperature threshold for activation of fresh air blower">
Adapt value in ° C

© 2013-2021 Daniel Fuchs page 65

Auxiliary heater - adjust temperatures for auxiliary heater operation
STG 18> Adaptation> ...

> Channel "Control parameters additional heating - lower temperature threshold ambient temperature"> Adjust value in ° C> Channel "Control parameters
additional heating - upper temperature threshold ambient temperature"> Adjust value in ° C

Deactivate the start / stop function

STG 19> Adaptation> ...

> Channel "EM_start_stop_requirement_ambient_temperature-Minimum_temperature"> change value to "50" (factory setting: -50)> Channel
"EM_start_stop_requirement_ambient_temperature-Maximum_temperature"> change value to "50" (factory setting: -50)

or

> Channel "Start / Stop start voltage limit"> Change value to "12" (factory setting: 7.6)

SWRA - deactivation
STG 09> Deactivate coding> Byte 13> Bit 3

SWRA - change delay time until triggering

STG 09> Access authorization: 31347> Adaptation> Channel "Windshield wiper SRA delay time> Adapt value in milliseconds (maximum 2500 ms)

SWRA - adapt washing behavior (frequency, duration)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Number of windshield wipers actuations front washing system per SRA activation"> Adjust value
> Channel "Windshield wiper SRA wash time"> Adjust value in milliseconds
> Channel "Windshield wiper SRA soaking pause time"> Adjust value in milliseconds
> Channel "Windshield wiper SRA post-wash time"> Adjust value in milliseconds

© 2013-2021 Daniel Fuchs page 66

The entire washing process is split up into two separate spray processes, the times can be adjusted as desired. The longer the washing times, the sooner your
washer fluid tank is empty!

Daytime running lights - switch off when the handbrake is on

STG 09> Access authorization: 31347> Adaptation> Channel "Daytime running lights / daytime running lights Switch off permanent running lights with
handbrake"> Set value to "active"

Daytime running lights - dimming when blinking

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire2SL VL B10 light function E 2"> Set value to "Flashing left active (both phases)" (factory setting: not active)> Channel "Luminaire2SL VL
B10 dimming value EF 2"> Set percentage value as required (factory setting: 0 )> Channel "Luminaire2SL VL B10-Dimming Direction EF 2"> Set value to
"minimize" (factory setting: maximize)> Channel "Luminaire3SL VR B21-Light function E 3"> Set value to "Flashing right active (both phases)" ( Factory
setting: not active)
> Channel "Luminaire3SL VR B21 dimming value EF 3"> Set percentage value as desired (factory setting: 0)> Channel "Luminaire3SL VR B21-Dimming
Direction EF 3"> set to "minimize" (factory setting: maximize)

Daytime running lights - dimming when blinking (slow dimming) (Seat Leon 5F)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire2SL VL B10 light function E 2"> Set value to "Flashing left active (both phases); dimming up and down with p_t_blinken_rampe">
Channel "Luminaire2SL VL B10 dimming value EF 2"> Set percentage value as desired> Channel " Luminaire2SL VL B10-Dimming Direction EF 2 "> set value
to" minimize "> channel" luminaire3SL VR B21 light function E 3 "> value to" blinking right active (both phases); dimming up and down with
p_t_blinken_rampe "set> channel" Luminaire3SL VR B21 dimming value EF 3 "> Set percentage value as required> Set channel" Luminaire3SL VR B21-
Dimming Direction EF 3 "> to" minimize "

Daytime running lights - deactivate dimming when flashing (Audi A3 8V)

STG 09> Access authorization: 31347> Adaptation> ...

© 2013-2021 Daniel Fuchs page 67

 > Channel "Luminaire2SL VL B10 dimming value CD 2"> Set value to "100" (factory setting: 30)> Channel "Luminaire3SL VR B21 dimming value CD 3"> Set
value to "100" (factory setting: 30)

Daytime running lights - Simultaneous flashing with the turn signal (or alternately)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Luminaire2SL VLB10 light function G 2"> Adjust value to "Flashing left dark phase"> Channel "Luminaire2SL VLB10 dimming value GH 2"> Adjust
value to "0"> Channel "Luminaire2SL VLB10-Dimming Direction GH 2"> value up Adjust "minimize"> Channel "Luminaire3SL VRB21 light function G 3">
Adjust value to "Flashing right dark phase"> Channel "Luminaire3SL VRB21 dimming value GH 3"> Adjust value to "0"> Channel "Luminaire3SL VRB21-
Dimming Direction GH 3 "> Adjust the value to" minimize "

For flashing alternately, "flashing left / right light phase" must be set.

Daytime running lights - Inactive in LDS position 0

STG 09> Access authorization: 31347> Adaptation> Channel "Daytime running lights-daytime running lights only in switch position AUTO"> Set value to "active"

Daytime running lights - activate the menu item in the CAR menu
STG 09> Access authorization: 31347> Adaptation> Channel "Daytime running light / daytime running light activation by BAP or operating sequence possible">
Set value to "active"

Daytime running lights - fog lights only as daytime running lights

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light4TFL LB4 light function A 4"> Set value to "not active" (factory setting: daytime running light)> Channel "Light4TFL LB4 light function A 4">
Set value to "not active" (factory setting: daytime running light)> Channel "Light12NL LB45 light function C 12 "> set value to" daytime running light "(factory
setting: not active)> channel" lamp12NL LB45 dimming value CD 12 "> set value to" 40 "> channel" lamp13NL RB5 light function C 13 "> value to" Set
daytime running lights "(factory setting: not active)> Channel" Light13NL RB5 dimming value CD 13 "> Set value to" 40 "

© 2013-2021 Daniel Fuchs page 68

Daytime running lights - add fog lights in addition to daytime running lights
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light12NL LB45 light function B 12"> Set value to "Daytime running light"> Channel "Light13NL RB5 light function B 13"> Set value to "Daytime
running light"

Daytime running lights - taillights additionally active (with KZB and inside button = parking light always active)
STG 09> Access authorization: 31347> Adaptation> Channel "Daytime running light-daytime running light Permanent running light activated additional parking
light"> Set value to "active"

Daytime running lights - taillights additionally active (without KZB)

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Leucht23SL HLC10 light function D 23"> Change value to "Daytime running light" (factory setting: not active)> Channel "Light24SL HRA65 light
function D 24"> Change value to "Daytime running light" (factory setting: not active)> Channel "Light26NSL LA72 light function D 26 "> change value to"
daytime running light "(factory setting: not active)> channel" lamp27NSL RC6 light function D 27 "> change value to" daytime running light "(factory setting:
not active)

Daytime running lights - parking light point additionally active (Golf 7 AU)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light8FL LB39 light function C 8"> Set value to "Daytime running lights" not previously active> Channel "Light 8FL LB39 dimming value CD 8"> Set
value to "100"> Channel "Light 9FL RB2 light function C 9"> Set value to Set "daytime running lights" not active beforehand> channel "lamp 9FL RB2 dimming
value CD 9"> set value to "100"

Fuel gauge - adjustment / calibration

STG 17> Access authorization: 20103> Adaptation> Channel "Offset for values of tank calibration (calibration) -Offset encoder 1"> Adapt value in l (factory
setting: -12.8; value range: -8.0 to 8.0)

© 2013-2021 Daniel Fuchs page 69

Negative values lower the fuel needle, positive values raise it. Calculation and remaining range are also influenced.

Adjust button illumination (driving profile, ASR, ESP) brightness

STG 09> Access authorization: 31347> Adaptation> Channel "Interior lighting KL 58xd PWM-Y?" > Set value to in percent (factory setting: 10)

All Y values must be adjusted. These can all be set to one value or recreate the curve

Traffic Jam Assist & Emergency Assist - activation

Requirement is an ACC with 11-byte + coding as well as the Lane Assist with front camera (STG A5) for which there are corresponding parameters in VCP. The
front-end camera can possibly also be updated to a new version, in which case byte 14 bits 2-3 must also be set to "08 Perso_HC, Last setting".

STG A5> Upload parameters for TRAFFIC_ASSIST (EraseFullMemory active) (VCP)

STG A5> Coding> Byte 16> Bit 2-3 set to "08 EA_Variant2"

Activate STG 03> Coding> Byte 29> Bit 5

STG 13> Coding> Byte 04> Activate bit 2 ("Emergency Assist installed")

STG 09> Access authorization: 31347> Adaptation> Channel "Außenlicht_Blacker-Warnblinken_durch_Fahrerass according"> Set value to "active"

or

Activate STG 09> Coding> Byte 06> Bit 3

Surrounding lighting - activation / activation (retrofitting)

Activate STG 42> Coding> Byte 01> Bit 2

Activate STG 52> Coding> Byte 01> Bit 2

Surrounding area lighting - use as a maneuvering light

A control unit for Area View or RFK High (STG 6C) is required. The control unit must have at least software version 0607.
© 2013-2021 Daniel Fuchs page 70
STG 09> Access authorization: 31347> Adaptation> Channel "Aussenlicht_uebergreifend-Ambient light as maneuvering light"> Set value to "active"

Activate STG 6C> Coding> Byte 08> Bit 2

US parking light explicitly only in the parking light switch position

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light 0 BLK VL B36 light function C 0"> Set value to "Parking light in front (position light; marker light)"> Channel "Light 0 BLK VL B36 dimming
value CD 0"> Set percentage value as desired (factory setting: 0)> Channel "Light1BLK VRB20 light function C 1"> set value to "Parking light front (position
light; parking light)"> Channel "Light1BLK VRB20 dimming value CD 1"> set percentage value as desired (factory setting: 0)

Emulate US parking light via ambient lighting (dimmable / switchable in the CAR menu)
If the coding does not lead to success, it is possible that "Ambientelicht 3" and the "Ambiente_Applikationsträger_in_Tuertafel" must be used.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Interior light, luminaire configuration-Ambiente_Applikationszüge_in_Instrumententafel"> Set value to "built in"
> Channel "Interior light, luminaire configuration ambience menu with global off"> Set value to "active"
> Channel "Light 0 BLK VL B36 light function A 0"> Set value to "Ambient light 1"> Channel "Light 0 BLK VL B36 dimming value AB 0"> Set percentage value as
required> Channel "Light 0 BLK VL B36 light function C 0 "> set value to" handbrake is applied "> channel" light 0 BLK VL B36 light function D 0 "> set value
to" interior light "> channel" light 0 BLK VL B36 dimming value CD 0 "> value to" 0 " set> channel "lamp 0 BLK VL B36-Dimming Direction CD 0"> set value to
"minimize"> channel "lamp 0 BLK VL B36 light function F 0"> set value to "flashing left light phase"> channel "lamp 0 BLK VL B36 dimming value EF 0 "> set
value to" 100 "> channel"Luminaire 0 BLK VL B36-Dimming Direction EF 0 "> Set value to" maximize "> Channel" Luminaire 0 BLK VL B36-Light function H 0
"> Set value to" Flashing left dark phase "> Channel" Luminaire 0 BLK VL B36 dimming value GH 0 "> set value to" 0 "> channel" lamp 0 BLK VL B36-Dimming
Direction GH 0 "> set value to" minimize "> channel" lamp1BLK VRB20 light function A 0 "> set value to" ambient light 1 "> Channel "Lamp1BLK VRB20
dimming value AB 0"> Set percentage value as desired> Channel "Lamp1BLK VRB20 light function C 0"> Set value to "Handbrake is applied"> Channel
"Lamp1BLK VRB20 light function D 0"> Set value to "Interior light" > Channel "Luminaire1BLK VRB20 dimming value CD 0 "> set value to" 0 "> channel"
luminaire1BLK VRB20-dimming direction CD 0 "> set value to" minimize "> channel" luminaire1BLK VRB20 light function F 1 "> value to" flashing left light
phase " set> channel "luminaire1BLK VRB20 dimming value EF 1"> set value to "100"> channel "luminaire1BLK VRB20-dimming direction EF 1"> set value to
"maximize"> channel "luminaire1BLK VRB20 light function H 1"> value to " Flashing left Set dark phase "> Channel" Luminaire1BLK VRB20 dimming value GH
1 "> Set value to" 0 "> Channel" Luminaire1BLK VRB20-Dimming Direction GH 1 "> Set value to" minimize "Set> Channel "Luminaire1BLK VRB20-Dimming
Direction CD 0"> Set value to "minimize"> Channel "Luminaire1BLK VRB20 light function F 1"> Set value to "Flashing left light phase"> Channel

© 2013-2021 Daniel Fuchs page 71

 "Luminaire1BLK VRB20 dimming value EF 1"> Value set to "100"> channel "luminaire1BLK VRB20-Dimming Direction EF 1"> set value to "maximize">
channel "luminaire1BLK VRB20 light function H 1"> set value to "blinking left dark phase"> channel "luminaire1BLK VRB20 dimming value GH 1 "> set value
to" 0 "> channel" Leucht1BLK VRB20-Dimming Direction GH 1 "> set value to" minimize "Set> Channel "Luminaire1BLK VRB20-Dimming Direction CD 0"> Set
value to "minimize"> Channel "Luminaire1BLK VRB20 light function F 1"> Set value to "Flashing left light phase"> Channel "Luminaire1BLK VRB20 dimming
value EF 1"> Value set to "100"> channel "luminaire1BLK VRB20-Dimming Direction EF 1"> set value to "maximize"> channel "luminaire1BLK VRB20 light
function H 1"> set value to "blinking left dark phase"> channel "luminaire1BLK VRB20 dimming value GH 1 "> set value to" 0 "> channel" Leucht1BLK VRB20-
Dimming Direction GH 1 "> set value to" minimize "Luminaire1BLK VRB20 light function F 1 "> set value to" flashing left light phase "> channel"
luminaire1BLK VRB20 dimming value EF 1 "> set value to" 100 "> channel" luminaire1BLK VRB20 dimming direction EF 1 "> value to" maximize " set>
channel "lamp1BLK VRB20 light function H 1"> set value to "flashing left dark phase"> channel "lamp1BLK VRB20 dimming value GH 1"> set value to "0">
channel "lamp1BLK VRB20 dimming direction GH 1"> value set to "minimize"Luminaire1BLK VRB20 light function F 1 "> set value to" flashing left light phase
"> channel" luminaire1BLK VRB20 dimming value EF 1 "> set value to" 100 "> channel" luminaire1BLK VRB20 dimming direction EF 1 "> value to" maximize "
set> channel "lamp1BLK VRB20 light function H 1"> set value to "flashing left dark phase"> channel "lamp1BLK VRB20 dimming value GH 1"> set value to
"0"> channel "lamp1BLK VRB20 dimming direction GH 1"> value set to "minimize"Set value to "maximize"> Channel "Luminaire1BLK VRB20 light function H
1"> Set value to "Flashing left dark phase"> Channel "Luminaire1BLK VRB20 dimming value GH 1"> Set value to "0"> Channel "Luminaire1BLK VRB20-
Dimming Direction GH 1 "> set value to" minimize "Set value to "maximize"> Channel "Luminaire1BLK VRB20 light function H 1"> Set value to "Flashing left
dark phase"> Channel "Luminaire1BLK VRB20 dimming value GH 1"> Set value to "0"> Channel "Luminaire1BLK VRB20-Dimming Direction GH 1 "> set value
to" minimize "

Control US parking lights via the Sport driving profile (Leon III 5F)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light 0 BLK VL B36 light function A 0"> Set value to "Ambient light 4"> Channel "Light 0 BLK VL B36 dimming value AB 0"> Set percentage value as
required> Channel "Light 0 BLK VL B36 light function E 0 "> set value to" flashing left light phase "> channel" lamp 0 BLK VL B36 dimming value EF 0 "> set
value to" 100 "(H7) or" 127 "(LED)> channel" lamp1BLK VRB20 light function A 1 "> set value to" ambient light 4 "> channel" luminaire1BLK VRB20 dimming
value AB 1 "> set percentage value as required> channel" luminaire1BLK VRB20 light function E 1 "> set value to" flashing left light phase "> channel"
luminaire1BLK VRB20- Dimming value EF 1 "> value to" 100 "(H7) orSet "127" (LED)

and if desired

> Channel "Daytime running light / daytime running light Permanent running light activated, additional parking light"> Set value to "active"

Just like the ambient lighting, the light is only active with parking light and low beam. The last adaptation allows the light to also be used in daytime running
lights. The disadvantage here is that both the rear lights and the interior lighting (buttons, etc.) are permanently active.

© 2013-2021 Daniel Fuchs page 72

US daytime running lights or parking lights (indicators permanently dimmed for daytime running lights or parking lights / low beam)
STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light 0 BLK VL B36 light function C 0"> Set value to "Parking lights in general" or "Daytime running lights" (factory setting: not active)
> Channel "Luminaire 0 BLK VL B36 dimming value CD 0"> Set percentage value as required (factory setting: 0)
> Channel "Lamp1BLK VR B20 light function C 1"> Set the value to "Parking lights in general" or "Daytime running lights" (factory setting: not active)>
Channel "Lamp1BLK VR B20 dimming value CD 1"> Set percentage value as required (factory setting: 0)

The dimming does not work with LED indicators such as the Golf 7 R or Seat Leon FR 5F.

US daytime running lights or parking lights - dimming is canceled when flashing

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Light 0 BLK VL B36-Light function E0"> Set value to "Flashing left dark phase"
> Channel "Luminaire 0 BLK VL B36-Dimming Direction EF0"> Set value to "minimize" (factory setting: maximize)
> Channel "Lamp1BLK VR B20 light function E1"> Set value to "Flashing right dark phase"
> Channel "Leucht1BLK VR B20-Dimming Direction EF1"> Set value to "minimize" (factory setting: maximize)

US daytime running lights in addition to normal daytime running lights - switchable via the CAR menu
The coding allows a change between normal daytime running lights and normal daytime running lights + US daytime running lights in light switch position »0«.
For parking lights and low beam, you have to decide on a version in the coding.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "daytime running light / daytime running light activation by BAP or operating sequence possible"> set value to "active"> channel "light 0 BLK VL
B36 light function A 0"> set value to "active 100%"> channel "light 0 BLK VL B36 -Dimming value AB 0 "> set value to" 0 "> channel" light 0 BLK VL B36 light
function C 0 "> set value to" daytime running light "> channel" light 0 BLK VL B36 dimming value CD 0 "> set percentage value as desired > Channel
"Luminaire 0 BLK VL B36-Dimming Direction CD 0"> Set value to "maximize"> Channel "Luminaire 0 BLK VL B36 light function F 0"> Set value to "Flashing left
light phase"> Channel "Luminaire 0 BLK VL B36 dimming value EF 0 "> set value to" 100 ">Channel "Luminaire 0 BLK VL B36-Dimming Direction EF 0"> Set
value to "minimize"> Channel "Luminaire 0 BLK VL B36 light function H 0"> Set value to "Flashing left dark phase"> Channel "Luminaire 0 BLK VL B36 -
Dimming value GH 0 "> set value to" 0 "> channel" lamp 0 BLK VL B36-Dimming Direction GH 0 "> set value to" minimize "> channel" lamp1BLK VRB20 light
function A 1 "> value to" active 100% "set> channel" lamp1BLK VRB20 dimming value AB 1 "> set value to" 0 "> channel" lamp1BLK VRB20 light function C 1

© 2013-2021 Daniel Fuchs page 73

 "> set value to" daytime running light "> channel" lamp1BLK VRB20 dimming value CD 1 "> percentage value as desired set> channel "Luminaire1BLK VRB20-
Dimming Direction CD 10 "> set value to" minimize "> channel" luminaire1BLK VRB20 light function F 1 "> set value to" flashing left light phase "> channel"
luminaire1BLK VRB20 dimming value EF 1 "> value to" 100 " set> Channel "Luminaire1BLK VRB20-Dimming Direction EF 1"> Set value to "minimize">
Channel "Luminaire1BLK VRB20 light function H 1"> Set value to "Flashing left dark phase"> Channel "Luminaire1BLK VRB20 dimming value GH 1"> Value set
to "0"> channel "lamp1BLK VRB20-Dimming Direction GH 1"> set value to "minimize"> channel "lamp2SL VLB10 light function A 2"> change value from
"daytime running light" to "active 100%"> channel "Light3SL VRB21 light function A 3 "> Change value from" Daytime running light "to" Active 100% ">
Channel" Light4TFL LB4 light function A 4 "> Change value from" Daytime running light "to" Terminal 15 with overrun until vehicle comes to a standstill ">
Channel" Light5 TFL RB32 light function A 5 "> Change value from" daytime running lights "to" Terminal 15 with overrun until vehicle comes to a standstill
"Change terminal 15 with overrun until vehicle comes to a standstill "Change terminal 15 with overrun until vehicle comes to a standstill "

and if desired (then the US lighting is on for parking lights / low beam, otherwise always off)

> Channel "Light 0 BLK VL B36 light function D 0"> Set value to "General parking light (tail light; position light; parking light)"> Channel "Light1BLK VRB20
light function D 1"> Value to "General parking light (rear light; position light; parking light )" set

US daytime running lights / normal daytime running lights - switchable via the CAR menu
The coding allows a change between normal daytime running lights and US daytime running lights in light switch position »0«. For parking lights and low beam,
you have to decide on a version in the coding.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "daytime running light / daytime running light activation by BAP or operating sequence possible"> set value to "active"> channel "light 0 BLK VL
B36 light function A 0"> set value to "active 100%"> channel "light 0 BLK VL B36 -Dimming value AB 0 "> set percentage value as desired> channel" light 0
BLK VL B36 light function C 0 "> set value to" daytime running lights "> channel" light 0 BLK VL B36 dimming value CD 0 "> set value to" 0 " > Channel
"Luminaire 0 BLK VL B36-Dimming Direction CD 0"> Set value to "minimize"> Channel "Luminaire 0 BLK VL B36 light function F 0"> Set value to "Flashing left
light phase"> Channel "Luminaire 0 BLK VL B36 dimming value EF 0 "> set value to" 100 ">Channel "Luminaire 0 BLK VL B36-Dimming Direction EF 0"> Set
value to "minimize"> Channel "Luminaire 0 BLK VL B36 light function H 0"> Set value to "Flashing left dark phase"> Channel "Luminaire 0 BLK VL B36 -
Dimming value GH 0 "> set value to" 0 "> channel" lamp 0 BLK VL B36-Dimming Direction GH 0 "> set value to" minimize "> channel" lamp1BLK VRB20 light
function A 1 "> value to" active 100% "set> channel" luminaire1BLK VRB20 dimming value AB 1 "> set percentage value as desired> channel" luminaire1BLK
VRB20 light function C 1 "> set value to" daytime running lights "> channel" luminaire1BLK VRB20 dimming value CD 1 "> value to" 0 " set> channel
"Luminaire1BLK VRB20-Dimming Direction CD 10 "> set value to" minimize "> channel" luminaire1BLK VRB20 light function F 1 "> set value to" flashing left
light phase "> channel" luminaire1BLK VRB20 dimming value EF 1 "> value to" 100 " set> Channel "Luminaire1BLK VRB20-Dimming Direction EF 1"> Set value
to "minimize"> Channel "Luminaire1BLK VRB20 light function H 1"> Set value to "Flashing left dark phase"> Channel "Luminaire1BLK VRB20 dimming value

© 2013-2021 Daniel Fuchs page 74

 GH 1"> Value set to "0"> channel "Leucht1BLK VRB20-Dimming Direction GH 1"> set value to "minimize"Flashing left Set light phase "> Channel"
Luminaire1BLK VRB20 dimming value EF 1 "> Set value to" 100 "> Channel" Luminaire1BLK VRB20-Dimming Direction EF 1 "> Set value to" minimize ">
Channel" Luminaire1BLK VRB20 light function H 1 " > Set value to "Flashing left dark phase"> Channel "Luminaire1BLK VRB20 dimming value GH 1"> Set
value to "0"> Channel "Luminaire1BLK VRB20-Dimming Direction GH 1"> Set value to "minimize"Flashing left Set light phase "> Channel" Luminaire1BLK
VRB20 dimming value EF 1 "> Set value to" 100 "> Channel" Luminaire1BLK VRB20-Dimming Direction EF 1 "> Set value to" minimize "> Channel"
Luminaire1BLK VRB20 light function H 1 " > Set value to "Flashing left dark phase"> Channel "Luminaire1BLK VRB20 dimming value GH 1"> Set value to "0">
Channel "Luminaire1BLK VRB20-Dimming Direction GH 1"> Set value to "minimize"Flashing left Set dark phase "> Channel" Luminaire1BLK VRB20 dimming
value GH 1 "> Set value to" 0 "> Channel" Luminaire1BLK VRB20-Dimming Direction GH 1 "> Set value to" minimize "Flashing left Set dark phase "> Channel"
Luminaire1BLK VRB20 dimming value GH 1 "> Set value to" 0 "> Channel" Luminaire1BLK VRB20-Dimming Direction GH 1 "> Set value to" minimize "

and if desired (then the US lighting is off with parking lights / low beam, otherwise always on)

> Channel "Light 0 BLK VL B36 light function D 0"> Set value to "General parking light (tail light; position light; parking light)"> Channel "Light1BLK VRB20
light function D 1"> Value to "General parking light (rear light; position light; parking light )" set

Adjust consumption display

STG 17> Adaptation> Channel "Display correction consumption and range"> Adapt percentage value (factory setting: 100; value range: 85 to 115)

Activate voice control (Audi A3 8V)

Activate STG 5F> Coding> Byte 24> Bit 1

Traffic sign recognition - activation (variant 1)

Multifunction camera (STG A5) must be installed. Function given with MIB2STD and all MIB HIGH. If no HUD (STG 82) is installed, the coding must be omitted.

STG A5> Coding> Byte 01> Activate bit 0 ("Traffic sign recognition (VZE) active")

STG 17> coding> byte 05> activate bit 2 ("traffic sign recognition installed / active")

STG 5F> Adaptation> ...

© 2013-2021 Daniel Fuchs page 75

 > Channel "Vehicle function list BAP-traffic_sign_recognition_0x21"> Set value to "activated"> Channel "Vehicle menu operation-
menu_display_road_sign_identification"> Set value to "activated"> Channel "Vehicle menu operation-
menu_display_road_sign_identification_over_threshold_high"> Set value to "activated"

STG 82> coding> byte 00> activate bit 0 ("traffic sign recognition, available")

Traffic sign recognition - activation (variant 2)

Multifunction camera (STG A5) must be installed. If no HUD (STG 82) is installed, the coding must be omitted.

STG A5> Coding> Byte 16> Activate bit 4 ("Traffic sign recognition (VZE) active [PR-QR9]")

STG 17> coding> byte 05> activate bit 2 ("traffic sign recognition installed / active")

STG 5F> Adaptation> ...

> Channel "Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21"> value to "enabled"> Set channel "Car_Function_List_BAP_Gen2-

traffic_sign_recognition_0x21_msg_bus"> value to "data Extended"> Set channel "Car_Function_Adaptations_Gen2-
menu_display_road_sign_identification"> value to "enabled"> Set channel "Car_Function_Adaptations_Gen2-
menu_display_road_sign_identification_over_threshold_high" > Set the value to "activated"

STG 82> coding> byte 00> activate bit 0 ("traffic sign recognition, available")

if errors remain in the ACC control unit, then additionally

STG 13> Coding> Byte 01> Activate bit 0 ("traffic_sign_detection")

Traffic Sign Recognition - Show cancellation signs

STG A5> Access authorization: 20103> Set channel "End of speed limit sign"> to "active"

Video in Motion (VIM) activation

VCP> Guided Functions> Function "VimManager"> Adjust parameters

© 2013-2021 Daniel Fuchs page 76

Hazard warning lights - automatic activation after emergency braking
STG 09> Access authorization: 31347> Adaptation> Channel "Außenlicht_Blinker-Notwarn_blinken_NBA_Phase_2"> Set value to "active"

Hazard warning button - adjust the brightness of the lighting

STG 09> Access authorization: 31347> Adaptation> Channel "Flasher control-hazard warning flasher search lighting factor"> Change factor

XDS - Advanced electronic differential lock adjust control strength

STG 03> Adaptation> Channel "Electronic differential lock"> Adapt value

Central locking - adjust the duration of the visual feedback

The ZV's visual feedback is divided into three parts (light-dark-light). The activation times can be adjusted for the »Facelift BCMs« (from index BA) in order to
lengthen or shorten the feedback.

STG 09> Access authorization: 31347> Adaptation> ...

> Channel "Feedback signals-ZV-Blinken_Dunkelzeit"> Adjust value in ms (factory setting: 200)> Channel "Feedback signals-ZV-Blinken_Hellzeit"> Adjust
value in ms (factory setting: 200)

Central locking - Do not unlock when removing the key

STG 09> Access authorization: 31347> Adaptation> Channel "Access control-automatic unlocking"> Set value to "not active"

© 2013-2021 Daniel Fuchs page 77