Installation Instructions

Control element
MultiControl | SmartControl | UniBox

+HDWLQJ

+HDWLQJ

SmartControl

MultiControl

English
Table of Contents

1 About this document 3 6 Technician mode 9

1.1 Purpose of the document 3 6.1 Functional description 9

1.2 Enclosed documents 3 6.2 Connecting the diagnostic adapter 9

1.3 Using this document 3 6.3 Selecting the Service menu 9

1.4 Use of symbols and highlighting 3 6.4 Service settings 9

6.5 Select heater 9

2 Safety 3 6.6 Min duration 9

2.1 Qualifications of installation personnel 3 6.7 Max duration 10

2.2 Regulations and legal requirements 3 6.8 Permanent mode 10

2.3 Safety precautions 4 6.9 Ventilation 10

6.10 Temperature range 10

3 Unit description 4 6.11 Show temperature 10

3.1 Scope of Delivery 4 6.12 UniBox 11

3.2 Type label 4 6.13 Undervoltage shutdown 11

3.3 Functional description 4 6.14 Max active timers 11

3.4 Versions 4 6.15 Unlock heater 11

6.16 Basic configuration 11

4 Installing the control element 5

4.1 Notes on installation 5 7 Troubleshooting 12
4.2 Installation location requirements 5 7.1 Fault code output 12

4.3 Installing the control element 5

4.4 Optional: Installing the UniBox 6 8 Technical data 14

5 Initial start-up 7 9 Electrical Connections 15

5.1 Information on initial operation 7 9.1 Connector designation MultiControl |

5.2 Starting up 7 SmartControl 15

5.3 Selecting the heater at a later date 7 9.2 Connector designation, UniBox 15

MultiControl | SmartControl | UniBox 2

1 About this document 2 Safety
1.1 Purpose of the document 2.1 Qualifications of installation person-
nel
These installation instructions are part of the device and contain
all the information required to ensure correct and safe installation. The installation personnel must have the following qualifications:
1.2 Enclosed documents ■■ Successful completion of Webasto training
■■ Corresponding qualification for working on technical systems
All documents are provided on the enclosed DVD and are available
2.2 Regulations and legal requirements
from http://dealers.webasto.com.
Printed copies of the following documents are enclosed with this Read
XX and follow the operating instructions before starting up
unit: the heater.
■■ Quick Start Guide
Directives Type-approval numbers for MultiControl | SmartCon-
■■ Information Sheet for Initial Start-up
trol | Unibox
1.3 Using this document
Radio interfe-
ECE R10 04 7319 MultiControl|SmartControl
Print
XX out these Installation Instructions as required. rence
Read
XX these Installation Instructions before installing the unit. The regulations of these guidelines are binding in the scope of the
Read
XX the operating instructions before operating the unit. Directive 70/156/EEC and/or 2007/46/EC (for new vehicle models
from 29/04/2009) and should also be observed in countries in which
1.4 Use of symbols and highlighting
there are no special regulations. Failure to follow the installation
Texts with the symbol refer to separate documents which are instructions will result in the invalidation of the type approval for
enclosed or can be requested from Webasto.
the heater and therefore invalidation of the general homologation
Texts with the symbol refer to technical features. of the vehicle. For vehicles with an EU type approval, an entry is not
Texts with the symbol or refer to possible material required in accordance with § 19 section 4 of appendix VIII b of
damage, risk of accident or injury.
StVZO. Country-specific registration regulations must be complied
Highlight Explanation with.
The variants MultiControl MAR/RV TT and MAR/RV ATE do not
33 Requirements for the following necessary action
comply with the legal requirements of UN/ECE Regulation No. 21
XX Necessary action
(interior fittings). These may therefore not be fitted in the head
impact zone (on the dashboard). This does not include fitting in the
exempted area behind the steering wheel with a deviation of up to
125 mm from the outer edge of the steering wheel. In the case of
adjustable steering wheels, the zone finally exempted is reduced to
the common area of the exempted zones for each of the driving
positions which the steering wheel may assume. Please refer to the
current version of UN/ECE R 21.
Intended use

The control element MultiControl | SmartControl is used to operate

the Webasto water or air heaters for cabin and engine preheating.
The control element MultiControl | SmartControl is currently ap-
proved for connection to certain Webasto water or air heaters.

MultiControl | SmartControl | UniBox 3

 DANGER 3 Unit description
■■ Do not operate the heater in closed rooms due to
the danger of poisoning and suffocation. 3.1 Scope of Delivery
■■ Always switch off the heater before refuelling. ■■ MultiControl | SmartControl
■■ The improper operation, installation or repair of ■■ Double-sided adhesive pad
Webasto heaters and control elements can cause fire ■■ Optional: bracket for MultiControl / SmartControl
or the leakage of deadly carbon monoxide. This can ■■ Optional: UniBox
lead to serious injury or death.
■■ Optional: bracket for UniBox
■■ Webasto shall not assume liability for defects or
damage that are the result that the installation and 3.2 Type label
operating instructions as well as the instructions
The type label is affixed to the rear of the control element.
contained therein being disregarded.
This liability exclusion particularly applies for: 3.3 Functional description
■■ installation by untrained personnel
■■ improper use Control Element
■■ repairs not carried out by a Webasto service The control element MultiControl | SmartControl is used to
workshop operate the Webasto water or air heaters for cabin and engine
■■ use of non-genuine parts preheating.
■■ Conversion of the heater without permission from
Depending on the heater installed and the application, it may
Webasto
additionally be necessary to install the UniBox (optional).
■■ If faulty always replace the complete control ele-
ment.
2.3 Safety precautions
Safety information on installation

ATTENTION Heating

Danger of electrical short circuit caused by live

parts
Disconnect
XX the vehicle on-board power supply
from the battery before installation.
Fig. 01: MultiControl / SmartControl element

ATTENTION 1 Submenu name

Danger of lacerations on sharp edges 2 Submenu symbol
3 Activated time settings
Fit
XX protectors on sharp edges.
4 Time
Safety information on operation 5 Quick start button
6 Control knob
WARNING
Risk of explosion in environments with combus- UniBox
tible vapours, flammable dust and hazardous
goods (e.g., petrol stations, tank facilities, The UniBox makes it possible to operate heaters that are not
fuel store, coal bunkers, timber yard or grain W-bus compatible using the MultiControl and SmartControl
warehouses) control elements. The UniBox also provides additional inputs and
Do
XX not switch on or operate the heater. outputs to expand the functional scope.
Communication between the UniBox and the control element
WARNING takes place via the W-bus. The UniBox is configured automatically
Risk of intoxication and suffocation from when the heater is selected on the control element.
exhaust fumes in closed rooms without exhaust The UniBox is fitted in the area of the vehicle that is not visible to
gas extraction the customer.
Do
XX not switch on or operate the heater. 3.4 Versions
The control element is available in two versions:
■■ SmartControl: control element with black frame and no timer
function.
■■ MultiControl: control element with silver-coloured frame, with
timer function.

MultiControl | SmartControl | UniBox 4

4 Installing the control 2 Adhesive pads (double-sided)
3 Control element

element Determine
XX

Locate
XX
the installation location.
bushing for control element wiring harness.
4.1 Notes on installation Rotate
XX control element wiring harness through installation
opening.
CAUTION XXAttach connector.
Danger of fire due to drilling into electrical
33Rear of control element is clean, dry and free of dust and
cables
grease.
Burn injuries
Position
XX control element.
Arrange
XX electrical cables behind the installation
Stick
XX adhesive pads to the control element.
area outside the drilling points.
Stick
XX control element onto the installation location.
CAUTION Optional installation using bracket
Injuries by touching sharp edges
Grazing of the skin, cuts 1 2 3 4
When
XX installing use
protective gloves.

4.2 Installation location requirements

Comply with legal requirements.

The installation location must satisfy the following requirements:

33Vehicle interior
33Ease of access
33Clear visibility
33Clean, dry and free of grease
33Protected from moisture
33Protected from heat, not in direct hot air flow
33Sufficient clearance behind installation location
4.3 Installing the control element
Installation using adhesive pads

1 2 3
Fig. 03: Installing the control element using a bracket
1 Installation location
2 Bracket
3 Screws
4 Control Element
Determine
XX the installation location.
Locate
XX bushing for control element wiring harness.
Install
XX bracket using the enclosed screws.
Pass
XX the control element wiring harness through from the front.
Clip
XX the control element into the bracket.

Fig. 02: Installing the control element using adhesive pads

1 Installation location

MultiControl | SmartControl | UniBox 5

 1 1 2

3 4

Fig. 06: Example of connecting UniBox (1), control element (2), heater (3)
and vehicle wiring harness (4)

Fig. 04: Example of connecting control element (1) to heater (2)

4.4 Optional: Installing the UniBox

Fig. 05: Optional: Installing the UniBox using a bracket

Determine
XX the installation location.

Fit the unit in the area of the vehicle that is not

visible to the customer.

Install
XX bracket using the enclosed screws.
Determine
XX the layout for the enclosed UniBox wiring harness.
Clip
XX the UniBox into the bracket.

MultiControl | SmartControl | UniBox 6

5 Initial start-up
5.1 Information on initial operation Setting the time:

WARNING
Inhaling poisonous gases in the enclosed
rooms
Danger of poisoning and suffocation
Never
XX operate the heater (also not with program-
med heating start) in closed rooms such as ga- Rotate
XX the control knob, set the hour.
rages or workshops that do not have an exhaust Press
XX the control knob.
extraction unit.
Rotate
XX the control knob, set the minutes.
In
XX workshops with exhaust extraction facilities,
Press
XX the control knob.
make sure that the exhaust extractor is fully
operational.

5.2 Starting up
33Heater is correctly installed. Heating

33Control element is correctly installed.

33Vehicle on-board power supply is connected to the battery
Fig. 10: Main menu
voltage.
When the main menu is displayed, initial start-up is completed.

Select heater The selected heater can be changed at a later date.

See “5.3 Selecting the heater at a later date” on
Manual heater selection is omitted in the event of page 7.
automatic heater detection.
5.3 Selecting the heater at a later date
Rotate the control knob and select the installed heater.
In the event of a Reset, all the settings and timer

programs on the control element are reset to the
default settings or to the values preset by the

technician.
+HDWHU  In the event of a Reset, the language is reset to
English.

Fig. 07: "Heater" menu element

Select
XX the “Settings” symbol from the main menu.
Press
XX the control knob.
Setting the day of the week:

Settings
Mon
Fig. 11: "Settings" menu element

Press
XX the control knob.
Fig. 08: Day of the week Select
XX the "Reset" menu element.

Rotate
XX the control knob, select weekday. Settings

Reset

Fig. 12: "Reset" menu element

Fig. 09: Setting the time Press

XX the control knob.

MultiControl | SmartControl | UniBox 7

 Settings

Reset

Fig. 13: "Confirm reset" menu element

Press
XX the control knob again to confirm the menu selection.
33The control element is restarted.
When
XX restarting the control element (the start screen is
displayed for 1.5 seconds), press the control knob and
quick start button simultaneously for 3 seconds.

+HDWHU 

Fig. 14: "Heater" menu element

Select
XX the desired heater.
Press
XX the control knob.

MultiControl | SmartControl | UniBox 8

6 Technician mode
6.1 Functional description 6.3 Selecting the Service menu
This specific function is not visible to the customer and is only In
XX the main menu, select the “Service” symbol .
enabled when the diagnostic adapter is used. This function can be
used to select the preset heaters and their settings and activate 
them. The limit values for temperature/operating duration etc.
can be adjusted by the technician if the presetting is not correct 
for the system as setup. As an alternative, the settings can also 6HUYLFH 
be carried out using the WTT (Webasto Thermo Test) diagnostic
software.
Fig. 17: "Service" menu element
Factory settings can only be changed by profession-
als. The items in the Technician menu are an extension
of the User menu and are available in addition. The
6.2 Connecting the diagnostic adapter “Service” symbol replaces the “Settings” symbol as
soon as the diagnostic adapter is connected.
Remove
XX the cover from the diagnostic adapter port.
6.4 Service settings
33The diagnostic cable connector is connected to the control
element. See chapter “6.2 Connecting the diagnostic adapter”
on page 9.
33“Service” symbol has been selected in the main menu.
Press
XX the control knob.
“Quick start” symbol is shown in the display.
6.5 Select heater
A different heater can be selected using this menu item. If a
different heater is selected, other settings from this menu are also
reset to the specific values for that heater. This includes deleting
the error memory.
33“Service” symbol has been selected in the main menu.
Fig. 15: Removing the cover 33“Quick start” symbol is shown in the display.
Rotate
XX the control knob in order to select the desired symbol
ATTENTION “Heater”.
Dust and moisture can damage the diagnostic 33The heater name is shown in the display.
adapter port
Rotate
XX the control knob in order to select the heater.
The unit may produce incorrect or no diagnostic
Press
XX the control knob in order to confirm selection.
information
Close
XX the cover on the diagnostic adapter port
6.6 Min duration
after use. Preset the minimum operating duration that the customer can
select from the menu when configuring the quick start button or
Connect
XX the diagnostic adapter to the control element. for heating/ventilation. The value for “Min duration” can be set
between 10 minutes and the “Max duration”.
33“Service” symbol has been selected in the main menu.
33“Quick start” symbol is shown in the display.
Rotate
XX the control knob in order to choose the desired symbol
“Min duration”.
XXPress the control knob in order to confirm selection.
33The min duration is shown in the display and the min duration
“hour” is flashing.
Rotate
XX the control knob in order to choose the desired min
duration “hour”.
Press
XX the control knob in order to confirm selection.
33The min duration is shown in the display and the min duration
Fig. 16: Connecting the diagnostic adapter “minute” is flashing.

MultiControl | SmartControl | UniBox 9

 Rotate
XX the control knob in order to choose the desired min 6.10 Temperature range
duration “minute”.
Press
XX the control knob in order to confirm selection. Here you can restrict the temperature range for air heaters that
the user can select from the menu when configuring the quick
6.7 Max duration start button or when heating. The minimum temperature can be
selected between 5°C and 20°C and the maximum temperature
Preset the maximum operating duration that the customer can
can be selected between 20°C and 35°C. This setting has no
select from the menu when configuring the quick start button or
effect for water heaters.
for heating/ventilation. The range for “Max duration” can be set
33“Service” symbol has been selected in the main menu.
between value for “Min duration” and the maximum time applica-
ble for the selected heater. 33“Quick start” symbol is shown in the display.
33“Service” symbol has been selected in the main menu. Rotate
XX the control knob in order to choose the desired symbol
33“Quick start” symbol is shown in the display. “Temperature range”.
33If the temperature setting function is not supported by the
Rotate
XX the control knob in order to choose the desired symbol
heater, “N/A” appears in the display and no settings can be
“Max duration”.
made here.
Press
XX the control knob in order to confirm selection.
XXPress the control knob in order to confirm selection.
33The max duration is shown in the display and the max duration
33The minimum temperature is shown in the display.
“hour” is flashing.
Rotate
XX the control knob to select the desired minimum temper-
Rotate
XX the control knob in order to choose the desired max
ature.
duration “hour”.
XXPress the control knob in order to confirm selection.
Press
XX the control knob in order to confirm selection.
33The maximum temperature is shown in the display.
33The max duration is shown in the display and the max duration
“minute” is flashing. Rotate
XX the control knob to select the desired maximum temper-
Rotate
XX the control knob in order to choose the desired max ature.
duration “minute”. Press
XX the control knob in order to confirm selection.
Press
XX the control knob in order to confirm selection. 6.11 Show temperature
6.8 Permanent mode This configures the temperature display in the status bar. If this
Here you can enable or block permanent operation of the heater option is switched off, the current temperature is not shown in the
by the user. Permanent mode is only possible in heaters that status bar. The temperature shown is always the current temper-
support this mode. If this option is selected for heaters that do not ature as reported by a connected sensor or the internal sensor in
support permanent mode, the heater determines the operating the MultiControl/SmartControl. Following a factory reset or after
duration when the user starts the functions heating/ventilation in selecting a new heater, all possible sensors are queried and the
permanent mode. first available sensor is selected for temperature determination.
The query sequence is as follows:
33“Service” symbol has been selected in the main menu.
33“Quick start” symbol is shown in the display. ■■ External sensor on the W-bus
■■ Sensor in the heater
Rotate
XX the control knob in order to choose the desired symbol ■■ External sensor connected to the UniBox
“Permanent mode”. ■■ Internal sensor of the MultiControl/SmartControl
Press
XX the control knob to choose between “On” and “Off”. 33The temperature can be displayed and hidden in the main
menu.
This setting is taken over without confirmation. 33“Service” symbol has been selected in the main menu.
33“Quick start” symbol is shown in the display.

6.9 Ventilation Rotate

XX the control knob to choose the desired symbol “Show
temperature”.
This option can be used to remove the “Ventilation” menu item Press
XX the control knob to choose between “On” and “Off”.
from the customer menu. This option has no effect for heaters
that do not support “ventilation”. This setting is taken over without confirmation.
33“Service” symbol has been selected in the main menu.
33“Quick start” symbol is shown in the display.
Rotate
XX the control knob in order to choose the desired symbol
“Ventilation”.
Press
XX the control knob to choose between “On” and “Off”.

This setting is taken over without confirmation.

MultiControl | SmartControl | UniBox 10

6.12 UniBox 6.15 Unlock heater
In principle, following a factory reset or heater selection, there
CAUTION
will be automatic detection of any UniBox that is present. If the
Possible risk of fire
UniBox is retrofitted, support can be forced by activating this
option so that the additional functions, such as ignition detection, Burn injuries
ADR, additional external button (like the quick start button) can Rectify
XX cause of error.
be used. The
XX heater may only be unlocked by trained
33“Service” symbol has been selected in the main menu. technicians.
33“Quick start” symbol is shown in the display.
Turn
XX the control knob in order to choose the desired “UniBox”. ATTENTION
Press
XX the control knob to choose between “On” and “Off”. Risk of damage to the heater
Rectify
XX cause of error.
This setting is taken over without confirmation.
The
XX heater may only be unlocked by trained
technicians.
Bring
XX up the Service menu.
6.13 Undervoltage shutdown
Rotate
XX the control knob clockwise.
If this option is activated, the supply voltage is continuously Select
XX the "Unlock heater" menu element.
checked during heating/ventilation mode and, if the configured
Press
XX the control knob on “Unlock heater”.
value is undershot for more than 5 seconds, the heater is shut
down. The heater can only be switched back on when the voltage Rotate
XX the control knob and select “Unlock heater OK” or
is stable above the configured value. Failure to reach the necessary “Back” (cancel).
value is indicated in the status bar by means of a battery symbol. Press
XX the control knob. Fault codes in the heater will be deleted.
33“Service” symbol has been selected in the main menu. 6.16 Basic configuration
33“Quick start” symbol is shown in the display.
In the event of a reset, all settings are restored to basic configura-
Rotate
XX the control knob in order to choose the desired symbol
tion except weekday and time. Following the reset, proceed as for
“Undervoltage shutdown”.
installation and initial start-up.
33If undervoltage shutdown is active, the display shows the preset
“Quick start” symbol is shown in the display.
value. If it is deactivated, “Off” is shown.
Rotate
XX the control knob in order to choose the desired symbol
Press
XX the control knob in order to confirm selection.
“Factory reset”.
Rotate
XX the control knob to set the value or deactivate the
XXPress the control knob in order to confirm selection.
function (Off).
33“OK” is shown in the display.
Press
XX the control knob in order to confirm selection.
33Press the control knob in order to confirm selection.
6.14 Max active timers 33Then the restart is performed.
Only one timer can be activated as standard. Using this option,
you can increase the number of times that can be activated
simultaneously to as many as 21.
Please note the legal requirements, in particular that only one
activated timer is permitted for passenger cars.
33“Service” symbol has been selected in the main menu.
33“Quick start” symbol is shown in the display.
Rotate
XX the control knob in order to choose the desired symbol
“Max active timers”.
33The preset value (number of timers) is shown.
Press
XX the control knob in order to confirm selection.
Rotate
XX the control knob to set the value.
Press
XX the control knob in order to confirm selection.

MultiControl | SmartControl | UniBox 11

7 Troubleshooting
7.1 Fault code output

The heater will output a fault code on the control An error that has occurred is shown on the control
element if a fault occurs during heating mode. element display as Txx or Fxx and the LED flashes
Pressing
XX the quick start button confirms the error red. The error display also appears after waking
display. up the control element from standby and must be
confirmed by pressing the control knob or the quick
start button. This error is saved in the error entries
You will find further information in the operating in the control element menu (menu element “Error
instructions. entry”) and can be called up. Selecting “Reset” in
the customer menu deletes all error entries for the
control element and the UniBox.
Table of internal control element errors “Txx”

Fault code Faults Fault description Troubleshooting

Ted Supply voltage too high Supply voltage exceeds 36V. Check car electrical installation.
Te3 Display background illumination faulty Contact Webasto service workshop.
Te4 Defective LED status Contact Webasto service workshop.
Temperature sensor of MultiControl/SmartControl
Te5 Temperature sensor error Contact Webasto service workshop.
faulty.
Temperature from external sensor (W-bus) cannot
Te6 W-bus temperature sensor error Check installation. Replace sensor if necessary.
be read correctly.
T12 Communication error on the W-bus Check installation.
Te7/Te8 Flash Contact Webasto service workshop.
Tea Faulty feedback signal from heater (ST) Check installation.
Tec Control knob sticking Control knob pressed for longer than 10 seconds. Contact Webasto service workshop.
Check installation. Ensure that the consumer at
T46 Excess current/short circuit at switch output SAU1 Current exceeds 500mA. the switch output SAU1 is not drawing more than
500mA.
Charge the battery and check car electrical instal-
Te0 Reduced voltage Supply voltage is below value set by technician.
lation.
Charge the battery and check car electrical instal-
T84 Operating voltage too low Supply voltage is less than 8V.
lation.
The error disappears automatically when the
Ambient temperature is outside the operating range
Te1 Ambient temperature too low/high ambient temperature is once more within the range
of -20°C to +70°C.
of -20°C to +70°C.
In case of voltage interruption lasting more than 8
minutes: Enter day/time again.
Teb RTC fault
If this error appears without voltage interruption:
Contact Webasto service workshop.

Error with UniBox connected and analogue heater

Fault code Faults Fault description Troubleshooting

Fed Supply voltage too high Supply voltage exceeds 36V. Check car electrical installation.
The temperature from the external sensor Check installation. Contact Webasto service
F5d Temperature sensor error
connected to the UniBox cannot be read correctly. workshop.
F12 Communication error on the W-bus Check installation.
Fe7/Fe8 Flash Read/write from/to the internal memory failed. Contact Webasto service workshop.
The UniBox is receiving an implausible signal. Check installation. Contact Webasto service
Fe9 Signal from switch output SAU1 not plausible
workshop.

Fea Faulty feedback signal from heater (ST) Check installation.

External control knob pressed for longer than 10 Check installation. Contact Webasto service
Fec External control knob sticking
seconds. workshop.
F01 to F0F Heater error Please look through the heater documentation. Contact Webasto service workshop.
The temperature from the external sensor
T5d UniBox temperature sensor error Check installation. Replace sensor if necessary.
connected to the UniBox cannot be read correctly.
Charge the battery and check car electrical instal-
T84 Operating voltage too low Supply voltage is less than 8V.
lation.

MultiControl | SmartControl | UniBox 12

Errors relating to a connected heater

Fault code Faults Fault description Troubleshooting

F01 to F99 Heater error (analogue)

F01 to FFE See workshop manual for heater Contact Webasto service workshop
Heater error (W-bus)
H01 to Hxx

MultiControl | SmartControl | UniBox 13

8 Technical data
Control Element MultiControl / SmartControl UniBox
Rated voltage [V] 12 to 24

Maximum current consumption (during

17 to 23 12
operation without external relay) [mA]
Maximum current consumption (in standby)
0.5
[mA]

Permissible ambient temperature [°C]

-40 to +75 / -40 to +90
(operation/storage)

Control element dimensions [mm]

68 / 15 (9.5 without control knob) / 48 90 (104 with connected wiring harness) / 60 / 25
(length/depth/height)

Weight [g] 41 66

MultiControl | SmartControl | UniBox 14

9 Electrical Connections
9.1 Connector designation 9.2 Connector designation, UniBox
MultiControl | SmartControl
No. Colours Description Remarks
No. Colours Description Remarks Contact 1 red KL30 Plus+ (control element)

The connection is configured Contact 2 brown KL31 Earth- (control element)

differently depending on Contact 3 yellow W-bus W bus (control element)
the heater selected. Please
note that there is no W-bus Switch output, heating
Contact 4 grey SAU1 switch output
W Bus / Low Switch / on this line for heaters with (control element)
Contact 1 yellow
Diagnostics analogue control. W-bus
Contact 5 red KL30 Plus+
diagnostics are only possible
with a W-bus heater Contact 6 brown KL31 Earth-
connected or with a UniBox
connected. green /
Contact 7 W-bus W-bus
white
max. switching current
Contact 2 black SAU1 switch output Switch output, heating (high
500 mA Contact 8 black SAU1 switch output
side) from UniBox
Contact 3 red KL30 Plus+
Switch output, ventilation
Contact 4 brown KL31 Earth- red / (low side) from UniBox
Contact 9 SAU2 switch output
white max. switching current
20mA

4 Contact 10 TS (Plus) External temperature sensor

Contact 11 TS (Earth) External temperature sensor
Contact 12 blue SWG (Plus) Setpoint input

1 Contact 13 white SWG (Earth) Setpoint input

3
black /
Contact 14 KL15 Ignition
grey
ADR operation
2 Contact 15 violet ADR (TRS)
Display on control element

Fig. 18: Control element connections Switch input

Contact 16 GREEN SEI External button for
switching on and off
red /
Contact 17 ST / status Fault code / status
black
white / Multifunctional input (air
Contact 18 Multifunction
red heater)

18

10
Fig. 19: UniBox connections

MultiControl | SmartControl | UniBox 15

In multilingual versions the German language is binding. You can request your language if it is missing.

Ident. No. 9030531B • 07/18 • Errors and omissions excepted • © Webasto Thermo & Comfort SE, 2018
The telephone number of the respective country can be obtained from the Webasto service point flyer or the homepage
of your respective Webasto country representative.

Webasto Thermo & Comfort SE

Postfach 1410
82199 Gilching
Germany

Visitors Address:
Friedrichshafener Str. 9
82205 Gilching
Germany

Technical Extranet: http://dealers.webasto.com www.webasto.com

16