RAJKOT – KANALUS DOUBLING

PROJECT

DESIGN REPORT FOR BR NO 395

(2x12. PSC U-SLAB ON U/S SIDE)

DATE: NOTE NO.: REV.: SHEETS:

FEB-2023 CASAD/ZW/233/1 R2 227

SUBMITTED TO CONTRACTOR

Zetwerk-Trenzet (JV)
DESIGN CONSULTANT

CASAD
th
CONSULTANTS PVT.LTD.
15 Floor Solitaire Sky, B/s Hyatt Regency Hotel,
Opp. Gujarat Vidyapith,Ashram
Road,Ahmedabad-380014
www.casadconsultants.com

PROJECT MANAGEMENT
PROOF-CHECK CONSULTANT
CONSULTANT

Intercontinental Consultants and

Technocrats Pvt. Ltd.
 SALIENT FEATURES OF DESIGN BASIS NOTE

Introduction
This Design Basis report highlights salient features of design basis of the Bridge No. 395 for 32T Railway
loading Rajkot – Kanalus Doubling Project.
The design basis lays down the Technical Design hypothesis and the loads to be adopted for designing the
structures, the permissible structural parameters as per relevant Indian codes of practice and a schedule of
design and drawings that shall be adopted.

Concept and Structural System

Open foundations:
Flexure theory shall be used for design of the open foundations and one way and two-way shear checks
shall be made as per the codal provisions. Grouting for ground improvement and rock anchors if required
on the basis of soil investigation reports shall be provided.
Safe bearing capacity:
SBC at founding levels shall be as per the Soil Investigation reports based on the confirmatory boreholes
at site.
For the combinations of loading under wind or Seismic, 25% higher bearing pressure shall be allowed.
Reduced area of contact shall not be less than as specified in IRS SUBSTRUCTURE CODE/ IRC:78-2014.

Codes and order of precedence

It is proposed to use IRS, IRC and BIS Standards wherever applicable for the Bridge.

Design Loads
Design loads will be taken from the IRS codes and applied as nominal loads for the limit state analysis.
Wind loads as applicable for the relevant zones shall be taken as per IRS Bridge rules and IRC standards.
Seismic shall be taken as per the relevant zone and further detailed in below.
Rail Loading

Double track Broad Gauge loading comprising the IRS 32 t loading shall be the main loading for the design
of the Bridge.

Thermal Loading
Use of latest IRS substructure code as per regional climatic conditions shall be made.
Seismic Provisions
IRS Seismic Code-2020 for seismic design will be used for RCC/steel seismic detailing.

Wind
The wind speed, terrain and topography factors and height factors shall be taken as per the IS 875 Part III
as applicable to bridge site. Application and load combinations shall be as per IRS bridge rules as
applicable for Rail bridges.
Load Combinations and Partial Load factors
For concrete structure the combination of load and partial load factors will be taken according to IRS
concrete bridge code (New table 12). In this table the value of f3 shall be taken as 1.0 as IRS code already
takes this value into consideration.

For steel structures the working stress method shall be followed.

Permissible stresses under various load combinations:

Permissible stresses for concrete and steel shall be as per IRS sub-structure and concrete bridge code.
Rebar of Fe500D Grade confirming IS-1786 shall be used as reinforcement in all R.C.C. components of
the bridge.
Structural Deformation Limits
Limits will be calculated using the UIC codes for lateral motion. UIC checks if required may also be carried
out on vertical deformations particularly with regard to passenger comfort. For sub structure and pile
foundations deformation limits as specified in IRS Bridge Rules, IRS Sub structure code, IS 2911 and IRC
78 shall be followed in that order of preference.

Material and specifications

Partial safety factors for materials will be taken from relevant codes.

Bearings and Expansion Joints

MS roller cum rocker bearings shall be provided for the Truss spans and Elastomeric Bearings/PTFE shall
be provided for the steel composite girder decking spans as far as possible.
Deck Furniture
This shall be provided as per the Railway approved GAD for the Bridge.

Construction Tolerances
For Concrete Bridge Structures the tolerance of IRS Concrete Bridge Code shall be used as per Clause
6.5.
For steel structures Manufacturing Tolerances of IRS Steel Bridge shall be used.
Inspection, Maintenance and Access Systems
Maintenance provisions shall be specified in the contract. Ladder access will be required to all elements.
Landing platform will be provided as per requirement and site feasibility. Inspection platforms at pier caps
shall be proposed.

Bridge Health Monitoring and Warning Systems and Instrumentation

Instrumentation system in form of strain gauges etc. may be proposed if applicable in the construction
contract. The instrumentation system needs to be linked to the overall railway monitoring system. This
instrumental scheme if decided to be implemented will be finalized in consultation with Western Railways.

Design Standards
Available National Standards
The Indian Railways have a set of codes and standards for the design and construction of railway bridges
in India (IRS Standards). The IRS standards shall be supplemented by other Indian Standards (IS), which
provide some additional coverage.
 Table 1
General and Material

S N. ITEM DESCRIPTION
1 Bearing NA

2 Design Life 100 Years

3 Design Speed 100 Km / H as per GAD
4 Structural Steel Fe 500D
Reinforcement

5 Minimum Grade of Concrete

(i) Seismic Arrestor M 35
(ii) Bed Block/ Pier Cap M 35
(iii) Pier and Abutment M 35
(iv) Wing and Return M 35
(v) Foundation M 35
(vi) PCC Levelling Course M 15
6 Reinforcement Bars Rebar of grade Fe 500D as per IS 1786

10 Bolts NA

11 Expansion Joint Strip seal/Elastomeric Type expansion Joint shall be proposed

as per MOST specifications.
12 Exposure Condition Severe
 Table 2

Durability
A clear concrete cover as tabulated below shall be maintained for all components of the structure
Sr. No. Item Clear Cover
1 Cap and Substructure 50 mm
2 Wing and Return 50 mm
3 Open foundation 75 mm
 Table 3
LOAD COMBINATION AND PARTIAL LOAD FACTORS
1.0 Legends for Characteristic Loads (Qk) is given below for easy referencing
DL Dead Loads
SDL Superimposed Dead Loads
LL Vertical Live Loads
BA Braking and Tractive Forces
T Uniform Temperature
DT Temperature Gradient
DS Differential Settlement
W Design Wind Load
SW Service Wind Load
EQ Earthquake Load
B Blast Load
LWR Effects due to Long Welded Rails
DLR Derailment load
ER Loads during erection / construction stage
2.0 Steel structure.
Various Load combinations in the table above are as below: (4 stages)
2.1 In service stage load combinations
Combination 1: DL + SDL + LL + BA + DS
Combination 2: DL + SDL +LL+ DS + BA + SW
(SW corresponding to max. wind pressure at deck level of 150 kg/m2)
Combination 3: DL + SDL + LL + BA + DS +T + DT + LWR
Combination 4: DL + SDL + DS + W
Combination 5: DL + SDL + DS + EQ
Combination 6: DL + SDL +LL+BA+ DS +EQ
Combination 7: DL + SDL + LL + BA + DLR
Combination 8: DL + SDL +LL + BA + DS + B
2.2 Erection stage load combinations
Combination 9: DL + SDL + W + ER
Combination 10: DL + SDL + EQ + ER
 Table 4
Table for partial safety factors for reinforced concrete structures.

INDIAN RAILWAY STANDAARD CODE OF PRACTICE FOR PLAIN REINFORCED AND PRESTRESSED
CONCRETE FOR GENERAL BRIDGE CONSTGRUCTION
(CONCRETE BRIDGE CODE)
TABLE 12
LOADS TO BE TAKEN IN EACH COMBINATION WITH APPROPRIATE YfL
(Clauses 11.2 and 11.3)
LOAD LIMIT YfL TO BE CONSIDERED IN
STATE COMBINATION
1 2 3 4 5
Dead weight of concrete ULS 1.25 1.25 1.25 1.25 1.25
SLS 1.00 1.00 1.00 1.00 1.00
Superimposed dead load ULS 2.00 2.00 2.00 2.00 2.00
SLS 1.20 1.20 1.20 1.20 1.20
Wind During erection ULS - 1.25 - - -
SLS - 1.00 - - -
With dead and superimposed dead loads only and for ULS - 1.60 - - -
members primarily resisting wind loads. SLS - 1.00 - - -
With dead plus superimposed dead plus other ULS - 1.25 - - -
appropriate combination 2 loads. SLS - 1.00 - - -
Relieving effect of wind ULS - 1.00 - - -
SLS - 1.00 - - -
During erection. ULS - 1.25 - - -
SLS - 1.00 - - -
With dead and superimposed dead loads only. ULS - 1.60 - - -
Earth SLS - 1.00 - - -
quake With dead plus superimposed dead plus other ULS - 1.25 - - -
appropriate combination 2 loads. SLS - 1.00 - - -
Tempe Restraint against movement except frictional. ULS - - 1.50 - -
rapture SLS - - 1.00 - -
Frictional restraint. ULS - - - 1.50 -
SLS - - - 1.00 -
Differential temperature effect. ULS - - 1.15 - -
SLS - - 0.80 - -
Differential settlement ULS As specified by Engineer
SLS
Earth Fill retained and or live load surcharge relieving effect. ULS 1.70 1.70 1.70 1.70 -
pressure SLS 1.00 1.00 1.00 1.00 -
 Relieving effect. ULS 1.00 1.00 1.00 1.00 -
-
Erection temporary loads (when being considered). ULS - 1.30 1.30 - -
Live load on foot path ULS 1.50 1.25 1.25 - -
SLS 1.00 1.00 1.00 - -
Live load ULS 1.75 1.40 1.40 - -
SLS 1.10 1.00 1.00 - -
Derailment loads. SLS (As specified by Bridge Rules for
combination 5 only)

NOTE 1 – ULS: Ultimate limit state SLS: Serviceability limit state

NOTE 2 – Superimposed dead load shall include dead load of ballast track, ballast retainer, precast footpath, wearing
course, handrails, utility services, kerbs etc.
NOTE 3 – Wind and earthquake loads shall not be assumed to be acting simultaneously.
NOTE 4 – Live load shall also include dynamic effect, forces due to curvature exerted on track, longitudinal forces,
braking forces and forces on parapets.
 Table of Contents
1. Summary Sheet 1

2. Design of Abutment 5

3. Design of Pier 69

4. Adsec Report for Pier 156

5. Design of Wing Wall 170

6. Design of Return Wall 194

Br NO 395-R2 Summary Sheet
Summary Sheet

Common Data

Project RJT-KNLS Doubling Project

Bridge No 395
Revision R0
Chainage -
KM 749/6-7
Span 5 x 12.2 PSC Slab
Nos of Track 1
Degree of Curve 0
Seismic Zone IV
Standard Of Loading DFC
Expousre Condition Moderate

Common Levels
Rail Levels 31.447
Formation Levels 30.653
Bottom of Super Str 30.203
Average Bed Level 19.447
Bottom of Foundation-Abutment 16.447
Bottom of Foundation-Pier 16.447

Hydraulics
HFL 26.947
Discharge 400
Scour Level-Abt 18.947
Scour Level-Pier 18.947

Abutment
Type of Open
Foundation
Abutment
Sr No Item Unit Actual Permissible Result
AT INT CHECKING LVL
1 Minimum Reinforcement mm2 4908.74 3755.00 OK
2 ULS Moment resistance KN-m 1580.04 3808.58 OK
3 Crack Width mm 0.01 0.25 OK
4 Stress in Steel Mpa 125.91 375.00 OK
5 Stress in Concrete Mpa 3.57 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.30 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.40 OK
9 Secondary Reinforcement mm2 3140.00 2253.00 OK
AT TOP Of FOUNDATION 0.00
1 Minimum Reinforcement mm2 9817.48 3726.00 OK
2 ULS Moment resistance KN-m 6687.81 7297.29 OK
3 Crack Width mm 0.02 0.20 OK
4 Stress in Steel Mpa 271.65 375.00 OK
5 Stress in Concrete Mpa 11.39 17.50 OK
6 Area of Shear Reinforcement mm2 678.58 554.48 OK
7 Torsional Shear Stress and Capacity Mpa 0.69 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.38 OK
9 Secondary Reinforcement mm2 3140.00 2235.60 OK
AT TOE 0.00
1 Minimum Reinforcement mm2 8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3056.96 4770.59 OK
3 Crack Width mm 0.12 0.25 OK

Design of Substructure for Br. No. 395 1 of 218

Br NO 395-R2 Summary Sheet
4 Stress in Steel Mpa 175.01 375.00 OK
5 Stress in Concrete Mpa 7.44 17.50 OK
6 Area of Shear Reinforcement mm2 904.78 484.14 OK
7 Torsional Shear Stress and Capacity Mpa 0.93 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1130.40 1128.00 OK
AT HEEL 0.00
1 Minimum Reinforcement mm2 8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3198.40 4770.59 OK
3 Crack Width mm 0.00 0.20 OK
4 Stress in Steel Mpa 223.24 375.00 OK
5 Stress in Concrete Mpa 9.49 17.50 OK
6 Area of Shear Reinforcement mm2 565.49 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.24 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 2009.60 1128.00 OK
10 ULS Moment resistance ( Trans Diraction-RAFT) KN-m 4770.59 4755.96 OK

Sr No Item Unit Actual Permissible Result

FOUNDATION CHECKING-OPEN FOUNDATION
1 Max Foundation Pressure KN/m2 400.13 470.00 OK
2 Eccentricity Ratio- Along 4.39 4.00 OK
3 Eccentricity Ratio- Across 0.00 4.00 OK
4 Factor of Safety for Overturning- Normal Case 4.81 2.00 OK
5 Factor of Safety for Overturning- Seismic Case 5.18 2.00 OK
6 Factor of Safety for Sliding- Normal Case 3.47 1.50 OK
7 Factor of Safety for Sliding- Seismic Case 1.36 1.25 OK

PIER
Summary of Output
Sr No Item Unit Actual Permissible Result
PIER-OPEN FOUNDATION
1 Minimum Reinforcement mm2 8042.48 2184.00 OK
2 ULS Moment resistance KN-m 1696.82 3378.19 OK
3 Crack Width mm 0.17 0.25 OK
4 Stress in Steel Mpa 165.81 375.00 OK
5 Stress in Concrete Mpa 8.44 17.50 OK
6 Area of Shear Reinforcement mm2 235.62 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.24 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1004.80 890.40 OK
PIER CAP-ALONG
1 Minimum Reinforcement mm2 1884.96 1816.00 OK
2 ULS Moment resistance KN-m 1.44 707.29 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 0.71 375.00 OK
5 Stress in Concrete Mpa 0.02 17.50 OK
6 Area of Shear Reinforcement mm2 678.58 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.03 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 1.58 0.57 OK
9 Secondary Reinforcement mm2 1004.80 789.60 OK
PIER CAP-ACROSS
1 Minimum Reinforcement mm2 2945.24 1805.00 OK
2 ULS Moment resistance KN-m 0.00 1096.97 OK
3 Crack Width mm 0.00 0.20 OK
4 Stress in Steel Mpa 0.00 375.00 OK

Design of Substructure for Br. No. 395 2 of 218

Br NO 395-R2 Summary Sheet
5 Stress in Concrete Mpa 0.00 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.93 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 2.46 0.40 OK
9 Secondary Reinforcement mm2 1004.80 783.00 OK

Foundation Pressure and Stability Check Unit Actual Permissible Result

1 Allowed Eccentricity Ratio 4
2 Ratio of Along Eccentricity 7.50 4.00 OK
3 Ratio of Along Eccentricity 4.02 4.00 OK
2
4 Max Pressure -Without Distribution KN/m 201.14 470.00 OK
2
5 Min Pressure -Without Distribution KN/m -39.84 0.00 REDIS
2
6 Max Pressure -After Distribution KN/m 214.10 470.00 OK

RETURN
Sr No Item Unit Actual Permissible Result
AT INT CHECKING LVL
1 Minimum Reinforcement mm2 4825.49 2805.20 OK
2 ULS Moment resistance KN-m 825.17 2785.01 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 36.82 375.00 OK
5 Stress in Concrete Mpa 1.21 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.23 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 1130.40 1046.76 OK
AT TOP Of FOUNDATION
1 Minimum Reinforcement mm2 12867.97 5582.40 OK
2 ULS Moment resistance KN-m 10047.22 14492.04 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 87.28 375.00 OK
5 Stress in Concrete Mpa 3.39 17.50 OK
6 Area of Shear Reinforcement mm2 549.78 346.22 OK
7 Torsional Shear Stress and Capacity Mpa 0.61 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2009.60 1566.72 OK
AT TOE
1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 7929.39 8209.08 OK
3 Crack Width mm 0.20 0.20 OK
4 Stress in Steel Mpa 202.47 375.00 OK
5 Stress in Concrete Mpa 13.28 17.50 OK
6 Area of Shear Reinforcement mm2 791.68 719.52 OK
7 Torsional Shear Stress and Capacity Mpa 1.46 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1004.80 751.20 OK
AT HEEL
1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 6179.51 8209.08 OK
3 Crack Width mm 0.14 0.20 OK
4 Stress in Steel Mpa 159.12 375.00 OK
5 Stress in Concrete Mpa 10.43 17.50 OK
6 Area of Shear Reinforcement mm2 904.78 867.19 OK
7 Torsional Shear Stress and Capacity Mpa 1.73 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK

Design of Substructure for Br. No. 395 3 of 218

Br NO 395-R2 Summary Sheet

9 Secondary Reinforcement mm2 1004.80 751.20 OK

Sr No Item Unit Actual Permissible Result

FOUNDATION CHECKING-OPEN FOUNDATION- RETURN
1 Max Foundation Pressure KN/m2 261.48 470.00 OK
4 Factor of Safety for Overturning- Normal Case 5.49 2.00 OK
5 Factor of Safety for Overturning- Seismic Case 2.27 1.50 OK
6 Factor of Safety for Sliding- Normal Case 2.03 1.50 OK
7 Factor of Safety for Sliding- Seismic Case 1.84 1.25 OK

Design of Substructure for Br. No. 395 4 of 218

Br NO 395-R2 AN1
Project RJT-KNLS Doubling Project
Client WR-CPM-II-ADI Revision R0
Job Bridge NO 395 Abt no A1 Gr No 1
Prepared By JP Checked By VG App JG
Document No - Date -

Clause Description Value Unit Ref/Remarks

1.0 INPUT DATA

1.1 LEVELS
Rail LVL 31.447 m
Formation Level 30.653 m
Top of Abt Cap 30.163 m
Bottom of Abt Cap 29.663 m
Bed Level 19.447 m
HFL-Normal 26.947 m
HFL-SIESMIC 26.947 m
Top of Foundation 18.047 m
Bottom of Foundation 16.447 m
Intermediate Checking Level 23.855 m
Deepest Scour Level- Normal 18.947 m
Deepest Scour Level- Seismic 18.947 m
Low Water Level 19.447 m

1.2 SPAN Configuration & Super Structure Geometry

Material of Super Structure ( C- Concrete S- Steel) P
Type of Super Structure ( G-Girder S-Slab) S
Clear Span 12.200 m
Effective Span 12.863 m
Loaded Length of Girder 13.375 m
Ballast Cushion Provided = 0.350 m
1.3 LOADING
Standard of Loading 3 DFC
Live Load Surcharge 163.0 KN/m2
Dead Load Surcharge 71.0 KN/m2
Self weight of Slab 892.2 KN
Dead Load of p.way per Running m 65.0 KN/m
Total Live load on Girder 2157.8 KN
Total Longitudinal load on Girder 630.0 KN

1.4 Dimensions
Width of Abt Cap/ Track 4.800 m
Barrel Length of Abutment 7.850 m
Top Width of Abutment 2.000 m
Height from Formation Level to Top of Abt Cap 0.490 m
Depth of Abt Cap 0.500 m
Height from Bottom of Abt Cap to Top of Foundation 11.616 m
Batter (1000 if Vertical) 1000.0 H:V
Height of Intermediate Level from top of Foundation 5.808 m
Back batter (1000 if Vertical) 1000.0 H:V
Front Offset in Abutment at INT LVL 0.000 m
Front Offset in Abutment at Foundation 0.000 m
Length of Return 16809 mm
Skew Angle 0 Deg

Design of Substructure for Br. No. 395 5 of 218

Br NO 395-R2 AN1

1.4 Abt Cap

Thickness of Abt Cap = 0.500 m
Front Projection of Abt Cap 0.000 m
Back Projection of Abt Cap 0.000 m
End Thickness of Abt Cap 0.500 m
Back Chamfer 0.000 m
Thickness of Dirt Wall 0.300 m
Height of Dirt Wall 0.790 m

1.5 Foundation
Type of Foundation (1=Open, 2=Well, 3=Pile) 1
Depth of Scour from Top of Foundation 0.00
Thickness of Foundation 1.60 m
Toe Projection 4.50 m
Heel Projection 4.50 m
End Thickness - Toe 0.50 m
End Thickness - Heel 0.50 m
Type of Bridge ( 1= River Bridge , 2= Viaduct 3=CANAL) 1.00
Width of Footing Across the Track 7.85 m
Raft With Abt/Pier ( 1= NO , 2 = With Abt, 3= With Pier )
Raft With Return ( 4= Yes , "" NO ) =
Foundation off ( Across)

1.4 Material & Soil

Angle of internal friction of back fill f = 35.000 Deg
Angle of Friction of Wall with Soil d = 23.450 Deg
Coefficient of friction for soil m= 0.800
Angle of internal friction for Front soil f1 = 30.000 Deg
Cohesion 10.000 KN/m2
Grade of Concrete - fck
For Abutment Stem 35 Mpa
For Foundation 35 Mpa
For Cap 35 Mpa
Grade of Steel - fy 500 Mpa
Density of back fill 18.000 KN/m3
Density of Masonry 25.000 KN/m3
Front Delta 0.409 rad
Safe Bearing Capacity of Subsoil 470.000 KN/m2
Density of Submerged soil 8.000 KN/m3

1.4 Bearing
Bearing Material ( 1=Conc, 2 = Steel 3 = Elastomeric 4= 1
ROCKER, 5=PTFE )
Thickness of Bearing 0.040 m
Thickness of Pedestal 0.000 m
Total Thickness of Bearing + Pedestal 0.040 m
Dist from c/c of Bearing to Front of Abutment 1.432 m
Type of Bearing (1 = Fixed, 2 = Normal, 3=Free) 2
Bearing DIM Along 0.513 Across 0.002 m
Pedestal DIM Along 0 Across 0 m
Distance Between Bearings 1.800 m

1.4 Seismic
Zone = a = 0.05 b = 1 IV
Importance Factor i = 1.5
Method (1= Coeff. Method, 2= IRS Response Spectrum) 2

Design of Substructure for Br. No. 395 6 of 218

Br NO 395-R2 AN1

1.4 MISC
Type of Project (1= GC, 2 = New) 2
Type of Structure (1= Gravity type, 2 = RCC) 2
Height of Passive from Top of Foundation 0.900 m
Height of Passive from Bottom of Foundation 2.500 m
Dispersion in Long Load Allowed (Not Allowed = 1, Allowed = 2) 1 (Cl 2.8.3 Br Rule)
Width of Live Load Distribution (Sub Structure Code Cl 5.8.1 ) 3.000 m
FOS for Passive (0 = New, 1=Buried, 3 = Normal) 3.000
ALFA (Front batter) 0.000 rad
No Approach Slab 0.000
Eccentricity of Approach Slab from back face of Abutment 0.000
Weight of Approach Slab (with Live and Dead Loads) 0.000
Nos of Track 1

Design of Substructure for Br. No. 395 7 of 218

Br NO 395-R2 AN1
2 Geometry

2.1 Sectional Elevation

2.4 Long Elevation (m)

0.3

FORMATION LEVEL--30.653

0.79
TOP OF CAP--30.163

0.5
BOTTOM OF CAP--29.663

HFL--26.947
11.616

BED LVL--19.447

SCOUR LEVEL--18.947
2

TOP OF FOUNDATION--18.047

4.5 1.3 4.5

1.1
0.5

BOTTOM OF FOUNDATION--16.447

Design of Substructure for Br. No. 395 8 of 218

Br NO 395-R2 AN1

Reinforcement Optimisation

Bar Layer-1 Layer-2

Location Actual/Reqd Capacity/Pro
No Dia Spac Dia Spac
INT CHK LVL
Back Vert 25 100 1580 3809 OK
Dis-Horz 20 100 2253.0 3140.0 OK
Shear 10 Leg 5 200 0.0 392.7 OK
TOP OF FND
Back Vert 25 100 25 100 6688 7297 OK
Dis-Horz 20 100 2235.6 3140.0 OK
Shear 12 Leg 6 300 554.5 678.6 OK
TOE
Back Vert 32 100 3057 4771 OK
Dis-Horz 12 100 1128.0 1130.4 OK
Shear 12 Leg 8 200 484.1 904.8 OK

Heel
Top main 32 100 3198 4771 OK
Dis-Horz 16 100 1128.0 2009.6 OK
Shear 12 Leg 5 200 0.0 565.5 OK
Main Transverse- For RAFT 32 100 4756.0 4770.6 OK
ABT CAP
Top main 16 120 832 1810 OK
Dis-Horz 12 200 499.2 565.2 OK
Shear 10 Leg 5 200 221.6 392.7 OK

Design of Substructure for Br. No. 395 9 of 218

Br NO 395-R2 AN1
Summary of Output

Abutment
Sr No Item Unit Actual Permissible Result
AT INT CHECKING LVL
1 Minimum Reinforcement mm2 4908.74 3755.00 OK
2 ULS Moment resistance KN-m 1580.04 3808.58 OK
3 Crack Width mm 0.01 0.25 OK
4 Stress in Steel Mpa 125.91 375.00 OK
5 Stress in Concrete Mpa 3.57 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.30 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.40 OK
9 Secondary Reinforcement mm2 3140.00 2253.00 OK
AT TOP Of FOUNDATION
1 Minimum Reinforcement mm2 9817.48 3726.00 OK
2 ULS Moment resistance KN-m 6687.81 7297.29 OK
3 Crack Width mm 0.02 0.20 OK
4 Stress in Steel Mpa 271.65 375.00 OK
5 Stress in Concrete Mpa 11.39 17.50 OK
6 Area of Shear Reinforcement mm2 678.58 554.48 OK
7 Torsional Shear Stress and Capacity Mpa 0.69 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.38 OK
9 Secondary Reinforcement mm2 3140.00 2235.60 OK
AT TOE
1 Minimum Reinforcement mm2 8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3056.96 4770.59 OK
3 Crack Width mm 0.12 0.25 OK
4 Stress in Steel Mpa 175.01 375.00 OK
5 Stress in Concrete Mpa 7.44 17.50 OK
6 Area of Shear Reinforcement mm2 904.78 484.14 OK
7 Torsional Shear Stress and Capacity Mpa 0.93 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1130.40 1128.00 OK
AT HEEL
1 Minimum Reinforcement mm2 8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3198.40 4770.59 OK
3 Crack Width mm 0.00 0.20 OK
4 Stress in Steel Mpa 223.24 375.00 OK
5 Stress in Concrete Mpa 9.49 17.50 OK
6 Area of Shear Reinforcement mm2 565.49 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.24 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 2009.60 1128.00 OK
10
ULS Moment resistance ( Transverse Diraction-RAFT)
KN-m 4770.59 4755.96 OK

Sr No Item Unit Actual Permissible Result

FOUNDATION CHECKING-OPEN FOUNDATION
1 Max Foundation Pressure KN/m2 400.13 470.00 OK
2 Eccentricity Ratio- Along 4.39 4.00 OK
3 Eccentricity Ratio- Across 0.00 4.00 OK
4 Factor of Safety for Overturning- Normal Case 4.81 2.00 OK
5 Factor of Safety for Overturning- Seismic Case 5.18 2.00 OK
6 Factor of Safety for Sliding- Normal Case 3.47 1.50 OK
7 Factor of Safety for Sliding- Seismic Case 1.36 1.25 OK

Design of Substructure for Br. No. 395 10 of 218

Br NO 395-R2 AN1
3.0 Load Calculation

3.1 Dead Load and SIDL

Loaded Length of Girder 13.375 m

SIDL (Weight of Track etc) 65 KN/ m

Self weight of Slab 892.2 x 1= 892 KN

No of Track (Drg.No.10281)
Total weight of Track 65.00 x 13.38 x 1= 869.38 KN
No of Track
Total Dead Load 892.2 + 869.38 = 1761.555 KN

WIDTH OF LOAD DISTRIBUTION

Dispersion of Load will be in 1:1 slope, but limited to actual 4.800 m at Abt Cap
Barrel length of Abutment 7.850 m

At Intermediate Checking Level

Depth from Bottom of Abt Cap =
29.663- 23.855 = 5.808 m

Width of Distribution = 2 x 5.81+ 4.8 = 16.416

= 7.850 m <= 7.850

At Top of Foundation
Depth from Bottom of Abt Cap = 29.663- 18.047
= 11.616 m

Width of Distribution = 2 x 11.6+ 4.8 = 28.03

= 7.850 m <= 7.850

At Bottom of Foundation
Depth from Bottom of Abt Cap = 29.663- 16.447
= 13.216 m

Width of Distribution = 2 x 13.2+ 4.8+ 31.23

= 7.850 m <= 7.850

3.1.1 At Intermediate Checking Level

DL of super Str.on each abutment = 892+ / (2 x 7.850 ) = 56.827 KN/m (Width)

DL of track on each abutment = 869.4 / (2 x 7.850 ) = 55.374 KN/m (Width)
Total DL of super str & track = 56.8+ 55.37 = 112.201 KN/m (Width)

3.1.2 At the Top of Foundation

DL of super Str.on each abutment = 892+ / (2 x 7.850 ) = 56.827 KN/m (Width)
DL of track on each abutment = 869.4 / (2 x 7.850 ) = 55.374 KN/m (Width)
Total DL of super str & track = 56.8+ 55.37 = 112.201 KN/m (Width)

3.1.3 At the Bottom of Foundation

DL of super Str.on each abutment = 892+ / (2 x 7.850 ) = 56.827 KN/m (Width)
DL of track on each abutment = 869.4 / (2 x 7.850 ) = 55.374 KN/m (Width)
Total DL of super str & track = 56.8+ 55.37 = 112.201 KN/m (Width)

3.2 LIVE LOAD

3.2.1 COEFF. OF DYNAMIC AUGMENT
= 0.15 + [8 / (6+L)] = 0.563 2.4.1.1 (a) Br Rule

Design of Substructure for Br. No. 395 11 of 218

Br NO 395-R2 AN1
CDA at Top of Slab/ Girder = 0.563 2.4.2.1 (a)Br Rule

CDA @ Bottom of Abt Cap = 0.5 x 0.563 = 0.281 Sub Str

Dynamic Augment at Intermediate Checking Level RL = 23.855

Depth of Inter Check Level from Bottom of Abt Cap =
29.663- 23.86 = 5.808 m
[(3 - 5.808 ) / 3] x 0.281 = 0.563 5.5 (a ) Sub Str

Dynamic Augment at Top of Foundation RL = 18.047

Depth of Top of Foundation from Bottom of Abt Cap =
29.663- 18.05 = 11.616 m
[(3 - 11.616 ) / 3] x 0.281 = 0.563

Dynamic Augment at Bottom of Foundation RL = 16.447

Depth of Top of Foundation from Bottom of Abt Cap =
29.663- 16.45 = 13.216 m
[(3 - 13.216 ) / 3] x 0.281 = 0.563

3.2.2 LIVE LOAD

Loaded length of Girder / Slab = 13.375 m

Live Load without Impact =1 x 2158 = 2157.763 KN
No of Track
At Intermediate Checking Level
Live load with Impact 2157.8
= x (1 + 0.563 ) = 3372.37 KN
LL on each abutment 3372.4
= / (2 x 7.850 ) = 214.801 KN/m (Width)

At the Top of Foundation

Live load with Impact 2157.8
= x (1 + 0.563 ) = 3372.37 Kn
LL on each abutment 3372.4
= / (2 x 7.850 ) = 214.80 Kn/m (Width)

At the Bottom of Foundation

Live load with Impact 2157.8
= x (1 + 0.563 ) = 3372.37 t
LL on each abutment 3372.4
= / (2 x 7.850 ) = 214.80 t/m (Width)

3.3 LONGITUDINAL LOAD (HORIZONTAL FORCE)

3.3.1 Loaded Length = 13.375 m

Total Longitudinal Load = 1 x 630 = 630.00 KN
No. of Track
3.3.2 Frictional Resistance of Bearing

Dispersion Allowed = 0.000 KN

Net Longitudinal Load = 630.00 - 0 = 630.00 KN

HORZ FORCE

As per IRC -6 Cl 211.5.1

Bearing type (1-fix,2-Normal, 3- Free) 2

Bearing Material ( 1=Conc, 2 = Steel 3 = Elastomeric 4= ROCKER ,5= PTFE) 1
Coff of Friction = m = 0.5000
Creep Strain for Elastomeric Bering
Shrinkage Strain for Elastomeric Bering
Total Strain for Elastomeric Bering ( Ts )
Half Span ( L1) 6432 mm
Horizontal Movement = D = Ts * L1 = mm
Bearing Size ( Along) -mm - BL mm
Bearing Size ( Transverse) -mm -BT mm

Design of Substructure for Br. No. 395 12 of 218

Br NO 395-R2 AN1
Bearing Thickness ( mm ) - T mm
Shear Strain in Bearing = Ss = D / T
Shear Modulus for Elastomeric Bering - Sm Mpa
Shear Stress = Sf = Ss * Sm Mpa
Addition Force = Vr * Itc = Sf * BL * BT KN

Horizontal Bearing Force

At
Bearing Type 2 Normal
Bearing Material 1 Conc

Dead Live
Load Load Long
Fixed Bearing Free Bearing Concrete Elastomeric
Bearing No

Final
Load Case

Reactio Reactio Load

n n Bearing Bearing Long
Rg Rq Fh Max of Fh-m(Rg+Rq) Force
m(Rg+Rq) Max of Fh/2 Fh/2 +
or 0.5 *Fh+m(Rg+Rq) or m(Rg) Vr * Itc

KN KN KN KN KN KN KN KN
1 2 880.8 1686 630 630 630

Skew Angle = 0 Deg

Net Load Along = 630.00 COS(0) = 630 KN

Net Load Across = 630.00 SIN(0) = 0 KN

Longitudinal Load on each Abutment

4.1 At Intermediate Checking Level = 630.0 / ( 2 x 7.850 ) = 40.1 KN/m (Width)
4.2 At Top of Foundation = 630.0 / ( 2 x 7.850 ) = 40.1 KN/m (Width)
4.3 At Bottom of Foundation = 630.0 / ( 2 x 7.850 ) = 40.1 KN/m (Width)

3.4 LWR Forces

LWR force to be Considered or Not ( 1= To be Consider, 0= Not to be Considered) 0

Nos of Track = 1
Total LWR Reaction on Abutment = 1 x 1454.2 = 1454.239 KN

Max Long Force in Normal condition ( Max of Breaking /Tractive) = 630.0 KN

Additional Force Due to Continuation of LWR = = 824.2 KN
LWR Force / m width = 824.239 / 7.850 = 0 KN/m

3.5 ACTIVE EARTH PRESSURE

Coff of Active Earth Pressure 5.7.1 Sub Str

Cos2(f - a)
2
Ka = Sin(f - d)Sin(f - i)
Cos2(a)Cos(a + d) 1 +
Cos(a+ d)Cos (a - i)

Item Notation Value Unit

Slope of Batter with Vert. a= 0.000 rad
Coeff. of internal friction of Soil f= 0.611 rad
Angle of friction bet. Wall & earth d= 0.409 rad
Angle of slope of fill with Horz. i= 0.000 rad

Coff of Active Earth Pressure Ka = 0.244

Design of Substructure for Br. No. 395 13 of 218

Br NO 395-R2 AN1

Horizontal Component of Active Earth Pressure

Pah = Pa Cos(a + d)
Acting at Y1= (h/3) above section considered

Vertical Component of Active Earth Pressure

Pav = Pa Sin(a + d)
Acting at X1 = Y1Cot (90-a) from face of Wall

FL 30.653

6.798

Int. Lvl 23.855

16.447 12.606

TOF 18.047

3.5.1 At Intermediate Checking Level

Height from Formation Level, h = 30.7- 23.9= 6.798 m
2
Pa = 0.5 x 0.24 x 18.0 x 6.798 =
101.7 KN/m (Width)
Horizontal Component
Pah = 101.7 x Cos( 0.00+ 0.409 ) =
93.3 KN/m (Width)
Will act at Y1 6.798 / 3 = 2.27 m
Vertical Component
Pav = 101.7 x Sin ( 0.00+ 0.409 ) =
40.45 KN/m (Width)
Will act at X1 = Y1Cot(90-a) = 2.27 Cot(90 - 0.000 ) = 0.000 m

3.5.2 At Top of Foundation

Height from Formation Level, h = 30.7 - 18.0 = 12.61 m
2
Pa = 0.5 x 0.24 x 18.0 x 12.61 = 349.5 KN/m (Width)

Horizontal Component

Pah = 349.5 x Cos( 0.00+ 0.409 ) = 320.7 KN/m (Width)

Will act at Y2 12.61 / 3 = 4.202 m

Vertical Component
Pav = 349.5 x Sin( 0.00+ 0.409 ) = 139.1 KN/m (Width)
Will act at X2 = Y2Cot(90-a) = 4.2 x Cot(90 - 0.000 ) = 0.000 m

3.5.3 At Bottom of Foundation

Height from Formation Level, h 30.7-
= 16.4= 14.206 m

2
Pa = 0.5 x 0.24 x 18.0 x 14.21 = 443.9 KN/m (Width)

Horizontal Component

Design of Substructure for Br. No. 395 14 of 218

Br NO 395-R2 AN1
Pah = 443.9 x Cos( 0.00+ 0.409 ) = 407.2 KN/m (Width)
Will act at Y2 14.206 / 3 = 4.735 m

Vertical Component
Pav = 443.9 x Sin( 0.00+ 0.409 ) = 176.7 KN/m (Width)
Will act at X2 = Y2Cot(90-a) = 4.7 x Cot(90 - 0.000 ) = 0.000 m

3.6 EARTH PRESSURE DUE TO SURCHARGE 5.8.2 Sub Str

Case-1: When depth of the section h is less than or equal to (L-B).

Case-2: When depth of the section h is more than (L-B).
2
Live Load Surcharge, S= 163 Kn/m
2
Dead Load Surcharge, V = 71 KN/m

3.6.1 At Intermediate Checking Level

Height from Formation Level, h = 6.798 m

Length of Abutment, L = 7.850 m
Width of Distribution, B = 3.0 m

Since h > (L-B) CASE NO. 2 will be used

(S+V)
P1 = x Ka h Will act at h/2
L

163.0+ 71 0.24+ 6.798

P1 = = 49.526 KN/m
7.85

Horizontal Component
P1h = = 49.526 x Cos( 0.00+ 0.409 )
= 45.436 KN/m Will act at h/2 3.399 m

Vertical Component
P1v = = 49.526 x Sin( 0.00+ 0.409 ) = 19.709 KN/m (Width)
Will act at X1 = Y1Cot(90-a) = 3.4 x Cot(90 - 0.000 ) = 0.000 m

(S+V) Ka (L-B)^2
P2 =
2B L

P2 = 28.562 t/m Will act at [h-(L-B)/3)] Y2 = 5.181 m

Horizontal Component
P2h = = 28.562 x Cos( 0.00+ 0.409 )
= 26.203 t/m Will Act at 5.181 m
Vertical Component
P2v = = 28.562 x Sin( 0.00+ 0.409 ) = 11.366 t/m (Width)
Will act at X2 = Y2Cot(90-a)
= 5.2 x Cot(90 - 0.000 ) = 0.000 m

3.6.2 At Top of Foundation

Height from Formation Level, h = 12.606 m

Length of Abutment, L = 7.850 m
Width of Distribution, B = 3.000 m

Since h > (L-B) CASE NO. 2 will be used

(S+V) Ka h
P1 =
L

Design of Substructure for Br. No. 395 15 of 218

Br NO 395-R2 AN1
P1 = 91.840 t/m Will act at h/2 = 6.303 m

Horizontal Component
P1h = 91.840 x Cos( 0.00+ 0.409 ) = 84.255 t/m
Will act at Y1 6.303 m
Vertical Component
P1v = 91.840 x Sin( 0.00+ 0.409 ) = 36.548 t/m

Will act at X1 = Y1Cot(90-a)

= 0.000 m

(S+V) Ka(L-B)^2
P2 =
2B L
P2 = 28.562 t/m, Will act at [H-(L-B)/3)] Y2 = 10.989 m

Horizontal Component
P2h = 28.562 x Cos( 0.00+ 0.409 ) = 26.203 t/m Will act at Y2 = 10.989 m

Vertical Component
P2v = 28.562 x Sin( 0.00+ 0.409 ) = 11.366 t/m
Will act at X2 = Y2Cot(90-a) = 11.0 x Cot(90 - 0.000 ) = 0.000 m

3.6.3 At Bottom of Foundation

Height from Formation Level, h 1=4.206 m

Length of Abutment, L = 7.850 m
Width of Distribution, B = 3.0 m

Since h > (L-B) CASE NO. 2 will be used

(S+V) Ka h
P1 =
L
P1 = 103.50 t/m Will act at h/2 = 7.103 m

Horizontal Component
P1h = 103.50 x Cos( 0.00+ 0.409 ) = 94.949 t/m
Will act at Y1 7.103 m
Vertical Component
P1v = 103.50 x Sin( 0.00+ 0.409 ) = 41.186 KN/m

Will act at X1 = Y1Cot(90-a) = 0.000 m

(S+V) Ka(L-B)^2
P2 =
2B L
P2 = 28.562 t/m, Will act at [H-(L-B)/3)] Y2 = 12.589 m

Horizontal Component
P2h = 28.562 x Cos( 0.00+ 0.409 ) = 26.203 t/m Will act at Y2 = 12.589 m

Vertical Component
P2v = 28.562 x Sin( 0.00+ 0.409 ) = 11.366 t/m
Will act at X2 = Y2Cot(90-a) = 12.6 x Cot(90 - 0.000 ) = 0.000 m

Design of Substructure for Br. No. 395 16 of 218

Br NO 395-R2 AN1
3.7 SELF WEIGHT CALCULATION

Weight of Abutment Cap

0.300

0.790
1

2 0.500
0.500
3
0.000
0.000 0.000 2.000 0.000

No. Description Shape SHP Horz. Vert. Densit Weigh CG WX CG WY

Fac (m) (m) y tW from above
(KN/m3 (KN) Vert base
) C/L-m (Y)
1 Dirt Wall Rec 1 0.3 0.79 25 5.925 -0.85 -5.036 0.895 5.303
2 Rec Portion Rec 1 2.000 0.500 25 25 0 0 0.25 6.25
3 Trap Portion Trap 1 2 0.000 25 0 0 0 0 0
Total 30.93 -5.036 11.55
CG of Abt Cap Mass from C/L = WX/W = -5.036 30.93 = -0.163 m
Vert CG of above Bottom of Cap = WY/W = 11.55 30.93 = 0.374 m

Weight of Stem Wall

Formation LVL 30.653

Bottom of Cap 29.663

2.000

1: 1000 5.808 1 : 1000

0 0 INT CHK LVL 23.855

1 2
11.616
3

TOF 18.047
0 0

0.28

Design of Substructure for Br. No. 395 17 of 218

Br NO 395-R2 AN1
STEM UP to INT CHK LVL

No. Description Shape SHP Horz. Vert. Densit Weigh CG WX CG WY

Fac (m) (m) y tW from above
(KN/m3 (KN) Vert base
) C/L-m (Y)
1 Back Batter Portion Tri 0.5 0 5.808 25 0 -1 0 1.936 0
2 Central Rec Portion Rec 1 2.000 5.808 25 290.4 0 0 2.904 843.3
3 Front Batter Portion Tri 0.5 0 5.808 25 0 1 0 1.936 0
Total 290.4 0 843.3
Horz CG of Abt Stem Mass from C/L = WX/W = 0 / 290.4 = 0m
Vert CG above INT CHK LVL = WY/W = 843.3 / 290.4 = 2.904 m

STEM up to Top of FND

No. Description Shape SHP Horz. Vert. Densit Weigh CG WX CG WY

Fac (m) (m) y tW from above
(KN/m3 (KN) Vert base
) C/L-m (Y)
1 Back Batter Portion Tri 0.5 0 11.616 25 0 -1 0 3.872 0
2 Central Rec Portion Rec 1 2.000 11.616 25 580.8 0 0 5.808 3373
3 Front Batter Portion Tri 0.5 0 11.616 25 0 1 0 3.872 0
Total 580.8 0 3373
Horz CG of Abt Stem Mass from C/L = WX/W = 0 / 580.8 = 0m
Vert CG from TOF = WY/W = 3373 / 580.8 = 5.808 m

Weight of Foundation

Formation Level = 30.653

Scour Level 18.947

Heel Toe

5 6
TOF 18.047
1.100
2 3
4 1.100

1.600
0.50 1 0.50
BOF 16.447

4.50 2.000 4.50

11.000

Design of Substructure for Br. No. 395 18 of 218

Br NO 395-R2 AN1
Weight of Foundation
Note :- CG from Back Face of Foundation has been Considered
No. Description Shape SHP Horz. Vert. Densit Weigh CG WX CG WY
Fac (m) (m) y tW from above
(KN/m3 (KN) Back base
) (Y)
1 Rec Portion-Bottom Rec 1 11 0.50 25 137.5 5.5 756.3 0.25 34.38
2 Rec Portion- Top Rec 1 2.000 1.100 25 55 5.500 302.5 0.863 47.47
3 Toe Triangular Port Tri 0.5 4.50 1.100 25 61.88 7.985 494.1 0.863 53.4
4 Heel Triangular Port Tri 0.5 4.50 1.100 25 61.88 3 185.6 0.863 53.4
5 Soil on Heel Rec 1 4.50 12.606 18.000 1021 2.25 2297 7.903 8070
6 Soil on Toe-Below Scour Rec 1 4.50 0.900 18.000 72.9 7.75 565 2.05 149.4
Total 1410 4601 8408
Horz CG of FND from Back of FND = WX/W = 4601 / 1410 = 3.262 m
Vert CG of above BOF = WY/W = 8408 / 1410 = 5.962 m

Total Weight up to- INT CHK LVL

Note Vertical axis of stem has been considered as ref Axis

Sr Description Weight of CG from Vert WX Individual CG from INT W*Y

No. Unit Ref Axis Vertical CG CHK LVL

W-KN X-m KN-m Y1 - m Y- m KN-m

1 Abt Cap 30.925 -0.16 -5.036 0.37 6.182 191.2
2 Abt Stem 290.4 0.00 0 2.90 2.904 843.3
Total 321.325 -5.036 1034

Horz CG from C/L = WX/W = -5.036 / 321.3 = -0.016 m

Vert CG From INT CHK LVL = WY/W = 1034 / 321.3 = 3.219 m

Total Weight up to- Top of Foundation

Note Vertical axis of stem has been considered as ref Axis

Sr Description Weight of CG from Vert WX Individual CG from INT W*Y

No. W-KN X-m KN-m Y1 - m Y- m KN-m
1 Abt Cap 30.925 -0.16 -5.036 0.37 11.990 370.8
2 Abt Stem 580.8 0.00 0 5.81 5.808 3373
Total 611.725 -5.036 3744

Horz CG from C/L = WX/W = -5.036 / 611.7 = -0.008 m

Vert CG From TOF = WY/W = 3744 / 611.7 = 6.121 m

Design of Substructure for Br. No. 395 19 of 218

Br NO 395-R2 AN1
Total Weight up to- Bottom of Foundation

Note Rearmost Part of Foundation has been considered as REF AXIS

Addition in Calculated CG wrt Axis of Stem 4.50 + 1 = 5.50 m

Sr Description Weight of CG from Vert WX Individual CG from INT W*Y

No. W-KN X-m KN-m Y1 - m Y- m KN-m
1 Abt Cap 30.925 5.34 165.1 0.37 13.590 420.3
2 Abt Stem 580.8 5.50 3194 5.81 7.408 4303
3 Foundation 1410.236 3.26 4601 5.96 5.962 8408
Total 2021.961 7960 13131

Horz CG from FND Back= WX/W = 7960 / 2022.0 = 3.937 m

CG From FND Back= = 3.94 m
Vert CG From BOF = WY/W = 13131 / 2022.0 = 6.494 m

3.8 PASSIVE EARTH PRESSURE

As per Cl 5.16.2.6 of Sub Str. (ACS - 23)
At Top of Foundation
Scour LVL = 18.95

2
1 0.900

h= 0.450 m

45- f/2 = 30 27 BOF = 18.05

x
1.559

h= x* 0.577 h = 1.559 - x 0.577

Hence
0.577 x = 0.900 - 0.577 x

x= 0.779 h = 0.577 * 0.779 = 0.450 m

Remaining Ht = 0.450 m

Design of Substructure for Br. No. 395 20 of 218

Br NO 395-R2 AN1
At Bottom of Foundation
Scour LVL = 18.95

2
1 2.500

h = 1.250 m

45- f/2 = 30 27 BOF = 16.45

x
4.330

h = x* 0.577 h = 4.330 - x 0.577

Hence
0.577 x = 2.500 - 0.577 x

x = 2.165 h = 0.577 * 2.165 = 1.250 m

Remaining Ht = 1.250 m

For Calculating the Passive Earth Pressure COULOMB's theory is followed.

Passive Earth Pressure,=P0.5 Kp w h2

Cos2(f+ a)
Kp= Sin(f + d) Sin(f + i) 2
Cos2a Cos(a - d) 1-
Cos(a- d) Cos (a - i)

f = 0.524 rad
a = 0.000 rad
d= 0.409 rad
i= 0.000 rad

Kp= 7.143

Pph = Pp Cos(d - a) Act at (h/3) above section

Ppv = Pp Sin(d - a) Act at X=Y Cot(90 - a)

Considering only Horizontal component because Vertical component will be ineffective.

3.8.1 Checking at Top of Foundation

Passive Height = 0.900 m =
2
Pp = 0.5 x 7.14 x 8.0 x 0.900 23.142 t/m = Surcharge
Pps = 7.143 8 0.45
Factor of Safety for Passive = 3 Pps = 11.57 t/m
Safe Passive Pr. = 23.142 / 3 = 7.714 KN/m
Ph = 7.714 x Cos( 0.409 - 0.000 ) Resisting Moment due to surcharge
= 7.077 t/m Will act @ h/3 = 0.300 m Pm = 11.57 x 0.225
Resisting Moment = 7.08 x 0.300 2.123 KN-m/mPm = 2.604 t-m/m

Design of Substructure for Br. No. 395 21 of 218

Br NO 395-R2 AN1
3.8.2 Checking at Bottom of Foundation
Passive Height Bed
= Lvl or Scour Lvl - BOF = 2.500 m
Pp = 0.5 x 7.14 x 8.0 x 2.500 2 = 178.57 KN/m Surcharge
Pps = 7.1438 1.25
Factor of Safety for Passive = 3 Pps = 89.28 t/m
Safe Passive Pr. = 178.57 / 3 = 59.522 KN/m
Ph = 59.522 x Cos( 0.409 - 0.000 ) Resisting Moment due to surcharge
= 54.606 KN/m Will act @ h/3 = 0.833 m Pm = 89.28 x 0.625
Resisting Moment = 54.6 x 0.833 45.505 KN-m Pm = 55.8 t-m/m

3.9 SEISMIC FORCE

Earth Pressure Due to Seismic Effect 5.12.6.1Sub Str

With Coeff Method.
ah = bx Ix ao
ah = 1.0 x 2 x 0.05 = 0.075 av = 0.08 / 2 = 0.038
As per Seismic Code -2017 IRS- SC-2017

Height of Abt Stem 12.12 m

3.9.1 Longitudinal SEISMIC COEFFICIENTS

Rocky Sa/g= 2.500 0.0<= T <=0.40
5.043 0.40<= T <=4.0

Medium Soil Sa/g= 2.500 0.0<= T <=0.55

6.858 0.550<= T <=4.0

Soft Soil Sa/g= 2.500 0.0<= T <=0.670

8.422 0.670<= T <=4.0

Shape (1 = Circular, 2= Rec) 2

Width of Section = 2000 mm
Depth of Straight Portion = 1000 mm
IL = 1000x2000^3 / 12
4
IL = 6.66667E+11 mm

DL Reactions = 112 KN

LL Reactions = 214.801 KN

Length ( L ) = 12116 mm

Grade of Concrete= 35

Modulus of elasticity E= 29,580.40 N/mm2

Moment of Inertia I = 6.667E+11 mm4

Deflection ( d ) 1 mm

Horizontal Deflection, for Cantilever structure

d= PL3
3 EI
P= d *3EI / L3 = 33263 N

Response Reduction Factor = R 2.5

Design of Substructure for Br. No. 395 22 of 218

Br NO 395-R2 AN1
Importance Factor = I 1.5

Zone No = IV

Zone Factor = Z 0.24

D.L & L.L of Super Structure = 327.00 kN

Period (T) = 0.20

P= 33262.60 N

Type of Soil = Medium Soil

Sa/g = 2.5000

Horizontal Coefficients = 0.18

Extra Seismic force For Foundation Design

ah = 0.180 av = 0.120 a Fh = 1 0.180 = 0.18
Cl 7.3 Seismic Code a Fv = 1 0.120 = 0.12

For Foundation

Response Reduction factor = R = 2 ( As per Table-3 )- IRS Seismic Code

Ratio of R for FND /STEM LONG = 2.5 / 2 = 1.25

Seismic Coff

For Stem
ah = 0.180 av = 0.120

For Foundation
ah = 0.225 av = 0.150

Level Int. Chk & TOF BOF

Slope of Batter with Vert. a= 0.000 rad
Coeff. of internal friction of Soil f = 0.611 rad
Angle of friction bet. Wall & earthd = 0.409 rad
Angle of slope of fill with Horz. i = 0.000 rad
Cl No 22.1.1 - IRS Seismic Code
At TOF
a tan-1a h tan-1 0.18 Pt I 1.090
l = = = 0.159
1+av 1 + 0.12 Pt II 0.664
Case I: With
"+" & "+"
value

2 2
1
Ca = (1 + a v) Cos (f - a - l) x = 0.393
2 Sin(f + d)Sin(f - i - l) =
Cosl Cos a Cos(a + d + l) 1 +
Cos(a+ d + l)Cos(a - i)
-1 -1
b tan a h tan 0.18 Pt I 0.923
l = = = 0.202
1-av 1 - 0.12 Pt II 0.643
"-" & "-" value
Case II: With

2 2
1
Ca = (1 + a v) Cos (f - a - l) x = 0.342
Sin(f + d)Sin(f - i - l) =
Cosl Cos2a Cos(a + d + l) 1 +
Cos(a+ d + l)Cos(a - i)

Design of Substructure for Br. No. 395 23 of 218

Br NO 395-R2 AN1
Final Ca = 0.393
Ka = 0.244
Dynamic Increment (Ca - Ka) = 0.149

Extra Force due to Dynamic Increment

Height From FL Density Force LA from Base

Level
h- m w-KN/m3 0.5*(Ca-Ka)*w*h2 m
INT CHK LVL 6.798 18.000 62.009 2.266
TOF 12.606 18.000 213.231 4.202
BOF 14.206 18.000 270.794 4.735

At Intermediate Checking Level

Due To Load Horz Vert. Horz Vert Horz L.A. Mome

(KN) Coeff. Coeff. Force- Force - Ecc (m) nt (KN-
KN KN m)
Super Str + Track 112.2 0.18 0.12 20.2 13.46 -0.432 6.308 121.6
Self WT 290.4 0.18 0.12 52.27 34.85 -0.016 3.219 167.7
Dynamic increment in Surcharge P1s 30.21 1 0 30.21 0 0 3.399 102.7
Dynamic increment in Surcharge P2s 17.42 1 0 17.42 0 0 5.181 90.28
Dynamic increment in Earth Pressure 62.01 1 0 62.01 0 0 2.266 140.5
Total 182.1 48.31 622.8

At Top of Foundation

Due To Load Horz Vert. Horz Vert Horz L.A. Mome

(KN) Coeff. Coeff. Force- Force - Ecc (m) nt (KN-
KN KN m)

Super Str + Track 112.2 0.18 0.12 20.2 13.46 -0.432 12.116 238.9
Self WT 580.8 0.18 0.12 104.5 69.7 0 5.808 607.2
Dynamic increment in Surcharge P1s 56.02 1 0 56.02 0 0 6.303 353.1
Dynamic increment in Surcharge P2s 17.42 1 0 17.42 0 0 10.989 191.5
Dynamic increment in Earth Pressure 213.2 1 0 213.2 0 0 4.202 896
Total 411.4 83.16 2287

At Bottom of Foundation

Due To Load Horz Vert. Horz Vert Horz L.A. Mome

(KN) Coeff. Coeff. Force- Force - Ecc (m) nt (KN-
KN KN m)

Super Str + Track 112.2 0.18 0.12 20.2 13.46 5.068 13.7 345.2
Self WT 2022 0.18 0.12 364 242.6 3.937 6.494 3319
Dynamic increment in Surcharge P1s 57.92 1 0 57.92 0 0 7.103 411.4
Dynamic increment in Surcharge P2s 17.42 1 0 17.42 0 0 12.589 219.3
Dynamic increment in Earth Pressure 270.8 1 0 270.8 0 0 4.735 1282
Total 730.3 256.1 5577

Design of Substructure for Br. No. 395 24 of 218

Br NO 395-R2 AN1
3.10 BUOYANT FORCE

10.1 At HFL Bot of BB

Width of Abutment at HFL = 2.00 + 0.00 + 0.00 + 2.003 m 2.000 29.66

Width at Intermediate Checking Level = 2.000 m

Width at Top of Foundation = 2.000 m
3
Volume bet Top and Bottom of Foundation = 12.7 m (per m width)

Volume of Abutment = A1 + A2 + A1 A2 h/3 HFL 0.000 26.95 0.000

Vol. between HFL and Intermediate Level =

(2.00 + 2.000 + √4.01) 1.031 = 6.188 m3 (per m width)

Vol. between HFL and Top of Foundation =

(2.00 + 2.000 + √4.01) 2.967 = 17.812 m3 (per m width)

Vol. between HFL and Bottom of Foundation =

17.812 + 12.7 = 30.5 m3 (per m width)

Buoyant force =Volume x Density of water

Buoyant force at Inter Checking Level = 15% 6.2 x 10.000 9.282 KN As per Cl 5.10.2 Sub St.
Buoyant force at Top of Foundation = 15% 17.8 x 10.000 26.72 KN As per Cl 5.10.2 Sub St.
Buoyant force at Bottom of Foundation =100% 30.5 x 10.000 304.6 KN As per Cl 5.10.1 Sub St.

10.2 At LWL Bot of BB 29.663

Width of Abutment at LWL = 2.00 + 0.01 + 0.00 + 2.01 + m 2.000

Width at Intermediate Checking Level = 2.000 m

Width at Top of Foundation = 2.000 m
Volume bet Top and Bottom of Foundation12.7
= m3 (per m width)

Volume of Abutment = A1 + A2 + A1 A2 h/3 LWL 19.447

0.000 0.010
Vol. between LWL and Intermediate Level =
(2.01 + 2.000 + √4.02) 0.000 = 0.000 m3 (per m width)

Vol. between LWL and Top of Foundation =

(2.01 + 2.000 + √4.02) 0.467 = 2.807 m3 (per m width)

Vol. between LWL and Bottom of Foundation =

2.807 + 12.7 = 15.5 m3 (per m width)

(Height h is zero, if LWL is below the level under consideration .)

Buoyant force =Volume x Density of water

Buoyant force at Inter Checking Level = 15% 0x 10 0 KN As per Cl 5.10.2 Sub St.
Buoyant force at Top of Foundation = 15% 2.81 x 10 4.211 KN As per Cl 5.10.2 Sub St.
Buoyant force at Bottom of Foundation =100% 15.5 x 10 154.6 KN As per Cl 5.10.1 Sub St.

Design of Substructure for Br. No. 395 25 of 218

Br NO 395-R2 AN1
4.0 Summary of Load and Moment

4.1 Intermediate Checking Level

CALCULATIONS FOR LOADING
Descript
Sl. No SYM Vertic Hzl. - ML MT
ion ECC
LA
KN KN m m KN-m KN-m
BASIC LOADS
0 0 0 0 0.000 0 0
1 DEAD LOADS
1a Super Str DL DL1+ 57 -0.43 -24.5
1b Self Weight DL2+ 321.3 -0.02 -5.0
1c Super Imposed Dead Load SIDL + 55.4 -0.43 -23.9
1d Buoyant Force-HFL HFL+ -9.3 0.0
1e Buoyant Force-LWL LWL+ 0.0 0.0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 25.0 -0.43 -10.8
2b Live Load LL1+ 215 -0.43 -92.8
2c Long Load LL2+ 40 6.308 253.1
3 Earth Pressure
3a Earth Pressure Eph+ 40.45 93.26 0.00 2.266 211.3
3b Surcharge Pressure -1 SP 1+ 19.71 45.436 0.00 3.399 154.4
3c Surcharge Pressure-2 SP2+ 11.37 26.20 0.00 5.181 135.8
3d Passive Resistance PP+ 0.00 0.00 0.00
4 Seismic Force
4a Long Seismic - (LS) + LS+ 48 182 623
4b Trans Seismic - (TS + TS+ 0 0 0 0
5 LWR FORCE
5a LWR FORCE + LW+ 0 6.308 0
6 Force Due To WIND
6a WIND+ WI 0 0 0 0
COMBINATION LOADS
1 2 3 4 5 6 7 8 9 10 11 12 13
SR No Description V HL ML MT
UNFACTORED - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
736 205 598 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

2 SP1+ 1 SP2+ 1 PP+ 1 PP+
704 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

3 SP1+ 1 SP2+ 1 PP+ 1 PP+
695 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

4 SP1+ 1 SP2+ 1 PP+ 1 PP+
704 112 386 0

5 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 496 165 448 0

6 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 465 72 237 0

7 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 455 72 237 0

8 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 465 72 237 0

Design of Substructure for Br. No. 395 26 of 218

Br NO 395-R2 AN1
Note:- As per Cl 2.8.5 Br
UNFACTORED- - LONG SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
9 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 525 246 734 0
0.67 LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
10 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 504 184 593 0
0.67 LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
11 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 498 184 593 0
LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
12 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 504 184 593 0
0.67 LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 Eph+ 0.67
13 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 LS+
365 232 717 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
14 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
344 170 576 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
15 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
337 170 576 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
16 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
344 170 576 0
Note:- As per Cl 2.8.5 Br
UNFACTORED- - TRANSVERSE SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
17 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 493 124 317 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
18 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 472 62 175 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
19 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 466 62 175 0
TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
20 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 472 62 175 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.34 LL2+ 0.67
21 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 TS+
332 124 386 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
22 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
311 48 159 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
23 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
305 48 159 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
24 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
311 48 159 0

UNFACTORED- - WIND - COMB-2

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
25 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 493 124 317 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
26 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 472 62 175 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
27 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 466 62 175 0
WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
28 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 472 62 175 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 Eph+ 0.67
29 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 WI
332 110 300 0

Design of Substructure for Br. No. 395 27 of 218

Br NO 395-R2 AN1

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
30 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
311 48 159 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
31 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
305 48 159 0

0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
32 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
311 48 159 0

UNFACTORED- - COMB-3

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

33 Eph+ 1 SP1+ 1 SP2+ 1 PP+
736 205 598 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

34 SP1+ 1 SP2+ 1 PP+ 1 PP+
704 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

35 SP1+ 1 SP2+ 1 PP+ 1 PP+
695 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

36 SP1+ 1 SP2+ 1 PP+ 1 PP+
704 112 386 0

37 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 496 165 448 0

38 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 465 72 237 0

39 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 455 72 237 0

40 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 465 72 237 0

Summary of UNFACORED Combination

1 Governing - Max. Axial load 736 205 0 598 0

9 Governing - Max. Long. Moment 525 246 0 734 0

1 Governing - Max. Trans. moment 736 205 0 598 0

23 Governing - Min Vertical 305 48 0 159 0

SLS Combination
SLS - -BASIC- COMB-1

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
1 LL2+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
771 209 608 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
2 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
739 116 396 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
3 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
730 116 396 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
4 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
739 116 396 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1

5 PP+
507 165 443 0

6 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 476 72 232 0

Design of Substructure for Br. No. 395 28 of 218

Br NO 395-R2 AN1

7 1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 466 72 232 0

8 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 476 72 232 0

Permanent Load
9 1 DL1+ 1 DL2+ 1.2 SIDL + 445 0 for crack width
-58 0

Live Load for crack

10 1 FPLL+ 1 LL1+ 1 LL2+ 240 40 width
150 0
Note:- As per Cl 2.8.5 Br
SLS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
9 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LS+
795 367 1089 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

10 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
764 274 878 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

11 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
755 274 878 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

12 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
764 274 878 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1

13 PP+ 1 LS+
555 347 1066 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

14 1 LS+
524 254 855 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

15 1 LS+
515 254 855 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

16 1 LS+
524 254 855 0
Note:- As per Cl 2.8.5 Br
SLS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
17 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 TS+
747 185 466 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

18 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
715 92 255 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

19 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
706 92 255 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

20 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
715 92 255 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1

21 PP+ 1 TS+
507 165 443 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

22 1 TS+
476 72 232 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

23 1 TS+
466 72 232 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

24 1 TS+
476 72 232 0

SLS- - WIND - COMB-2

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

25 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 WI
747 185 466 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

26 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
715 92 255 0

Design of Substructure for Br. No. 395 29 of 218

Br NO 395-R2 AN1

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

27 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
706 92 255 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1

28 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
715 92 255 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1

29 PP+ 1 WI
507 165 443 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

30 1 WI
476 72 232 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

31 1 WI
466 72 232 0

1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+

32 1 WI
476 72 232 0

SLS- - LWR- COMB-3

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

33 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LW+
736 205 598 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

34 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
704 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

35 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
695 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1

36 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
704 112 386 0

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+

37 1 LW+
496 165 448 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1

38 LW+
465 72 237 0

1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1

39 LW+
455 72 237 0

1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1

40 LW+
465 72 237 0

Summary of SLS Combination

9 Governing - Max. Axial load 795 367 0 1089 0

9 Governing - Max. Long. Moment 795 367 0 1089 0

1 Governing - Max. Trans. moment 771 209 0 608 0

10 Governing - Min Vertical 240 Live40

Load for crack width 150 0

ULS Combination
ULS - -BASIC- COMB-1

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
1 LL1+ 1.75 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
1107 351 1032 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
2 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1050 192 673 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
3 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1038 192 673 0

Design of Substructure for Br. No. 395 30 of 218

Br NO 395-R2 AN1

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
4 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1050 192 673 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
5 1.7 SP2+ 1.7 PP+
693 280 768 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
6 1.7 PP+ 1.7 PP+
636 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
7 1.7 PP+ 1.7 PP+
625 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
8 1.7 PP+ 1.7 PP+
636 122 409 0
Note:- As per Cl 2.8.5 Br
ULS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
9 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 LS+
1086 536 1580 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
10 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1029 378 1221 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
11 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1017 378 1221 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
12 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1029 378 1221 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
13 1.7 SP2+ 1.7 PP+ 1.25 LS+
754 508 1546 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
14 1.7 PP+ 1.7 PP+ 1.25 LS+
697 349 1187 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
15 1.7 PP+ 1.7 PP+ 1.25 LS+
685 349 1187 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
16 1.7 PP+ 1.7 PP+ 1.25 LS+
697 349 1187 0
Note:- As per Cl 2.8.5 Br
ULS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
Considered with Seismic
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
17 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 TS+
1025 308 802 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
18 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
968 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
19 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
957 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
20 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
968 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
21 1.7 SP2+ 1.7 PP+ 1.25 TS+
693 280 768 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
22 1.7 PP+ 1.7 PP+ 1.25 TS+
636 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
23 1.7 PP+ 1.7 PP+ 1.25 TS+
625 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
24 1.7 PP+ 1.7 PP+ 1.25 TS+
636 122 409 0

ULS- - WIND - COMB-2

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
25 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 WI
1025 308 802 0

Design of Substructure for Br. No. 395 31 of 218

Br NO 395-R2 AN1

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
26 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
968 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
27 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
957 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
28 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
968 150 442 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
29 1.7 SP2+ 1.7 PP+ 1.25 WI
693 280 768 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
30 1.7 PP+ 1.7 PP+ 1.25 WI
636 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
31 1.7 PP+ 1.7 PP+ 1.25 WI
625 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
32 1.7 PP+ 1.7 PP+ 1.25 WI
636 122 409 0

ULS- - COMB-3

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
33 LL1+ 1 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
1025 320 877 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
34 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
968 162 518 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
35 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
957 162 518 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
36 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
968 162 518 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
37 1.7 SP2+ 1.7 PP+
693 280 768 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
38 1.7 PP+ 1.7 PP+
636 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
39 1.7 PP+ 1.7 PP+
625 122 409 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
40 1.7 PP+ 1.7 PP+
636 122 409 0

Summary of ULS Combination

1 Governing - Max. Axial load 1107 351 0 1032 0

9 Governing - Max. Long. Moment 1086 536 0 1580 0

1 Governing - Max. Trans. moment 1107 351 0 1032 0

7 Governing - Min Vertical 625 122 0 409 0

Checking at Section INT CHK LVL

Type of Design SLAB

Design of Substructure for Br. No. 395 32 of 218

Br NO 395-R2 AN1
Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 25 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 1878 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 20 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 2000 mm
Average Overall depth of the section ( In Tapering Section) hav = 2000 mm
Clear cover to Ast Cc = 75 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) -58 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 150 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 1089
ULS-Total Moment 1580 kN-m
Ultimate Limit State Shear Vu = 536 kN
Ultimate Limit State Torsion, Tu 10 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Design of Substructure for Br. No. 395 33 of 218

Br NO 395-R2 AN1
Summary of Output ( Detail Calculation Given below) INT CHK LVL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 4908.74 3755.00 OK
2 ULS Moment resistance KN-m 1580.04 3808.58 OK
3 Crack Width mm 0.01 0.25 OK
4 Stress in Steel Mpa 125.91 375.00 OK
5 Stress in Concrete Mpa 3.57 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.30 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.40 OK
9 Secondary Reinforcement mm2 3140.00 2253.00 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A

h
cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 3755.00 mm2
As provided = 4908.74 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1877.5 mm
CG of reinforcements, dc 97.5 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 4908.74 + 0 4908.7 mm2
Reinf. steel area provided, Ast (flexure) 4908.7 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1783.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 3809 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1975 mm
Depth of Neutral axis NA, x= 346.74 mm
Distance from to the surface of the nearest longitudinal bar acr = 75.57 mm
Calculated strain in the tension reinforcement es = 0.000053
Strain at cracking LVL- Without stiffening Eff e1 = 0.0001 @cnom
Strain at cracking LVL- With stiffening Eff ets = -0.045249
Strain at cracking LVL- With stiffening Eff em = 0.0001 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.059E+11 mm4
Crack Width W cr = 0.0123 < 0.25 mm OK Tab-10
Stress in Steel fs = 10.55 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -0.30 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Design of Substructure for Br. No. 395 34 of 218

Br NO 395-R2 AN1
Maximum SLS Moment m 1089.00 KN-m
Stress in Steel fs = 125.91 Mpa
Permissible Stress in Steel 0.75fy = 375.00 OK Tab-11
Stress in Concrete fs = 3.57 Mpa
Permissible Stress in Concrete 0.5fck = 17.50 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1.00
depth factor, xs = 0.72
vc = 0.216*(pt)1/3 *min(fc,40)1/3 0.45 MPa
vc' = xs vc (2d/av) = 0.32 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.58 mm2
v < vc', hence Asv reqd = 0.00 mm2
Asv prov 392.70 mm2
v = Vu / (bd) 0.29 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 199.95 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.00 mm
Smaller Core Dim of Section x1min = 840.00 mm
Longer Outer Dim of Section hmax = 2000.00 mm
Longer Core Dim of Section y1max = 1840.00 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0120 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required

v + vt = 0.298 MPa < 4.43 MPa Torsional Capacity is OK

Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 1.86 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 490.87 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.00 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.54 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.00 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.91 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 1877.50 mm
Width of Section b= 1000.00 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 2253.00 mm2
Area of reinforcement Provided = 3140 + 0 3140.00 mm2

Design of Substructure for Br. No. 395 35 of 218

Br NO 395-R2 AN1

4.2 Top Of Foundation

CALCULATIONS FOR LOADING
Descript Vertic Hzl. -
Sl. No ML MT
ion SYM al X ECC
LA
KN KN m m KN-m KN-m
BASIC LOADS
0 0 0 0 0.000 0 0
1 DEAD LOADS
1a Super Str DL DL1+ 57 -0.43 -24.5
1b Self Weight DL2+ 611.7 -0.01 -5.0
1c Super Imposed Dead Load SIDL + 0.0 -0.43 0.0
1d Buoyant Force-HFL HFL+ -71.6 0.0
1e Buoyant Force-LWL LWL+ 0.0 0.0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 50.0 -0.43 -21.6
2b Live Load LL1+ 215 -0.43 -92.8
2c Long Load LL2+ 40 12.116 486.2
3 Earth Pressure
3a Earth Pressure Eph+ 139.10 320.68 0.00 4.202 1347.5
3b Surcharge Pressure SP1+ 36.55 84.255 0.00 6.303 531.1
3c Surcharge Pressure - Horz Comp SP2+ 11.37 26.20 0.00 10.989 288.0
3d Passive Resistance PP+ -7.08 0.30 0.00
4 Seismic Force
4a Long Seismic - (LS) + LS+ 83 411 2287
4b Trans Seismic - (TS + TS+ 0 0 0 0
5 LWR FORCE
5a LWR FORCE + LW+ 0 12.12 0
6 Force Due To WIND
6a WIND+ WI 0 0 0 0
COMBINATION LOADS
1 2 3 4 5 6 7 8 9 10 11 12 13
SR No Description V HL ML MT
UNFACTORED - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
1049 464 2509 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
2 SP1+ 1 SP2+ 1 PP+ 1 PP+
981 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
3 SP1+ 1 SP2+ 1 PP+ 1 PP+
910 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
4 SP1+ 1 SP2+ 1 PP+ 1 PP+
981 136 1161 0

5 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 784 424 2137 0

6 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0

7 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 645 96 789 0

8 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0
Note:- As per Cl 2.8.5 Br
UNFACTORED- - LONG SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
9 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 758 573 3052 0
0.67 LS+

Design of Substructure for Br. No. 395 36 of 218

Br NO 395-R2 AN1
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
10 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 713 354 2150 0
0.67 LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
11 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 665 354 2150 0
LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
12 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 713 354 2150 0
0.67 LS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 Eph+ 0.67
13 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 LS+
581 560 2964 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
14 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
536 340 2061 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
15 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
488 340 2061 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
16 SP2+ 0.67 PP+ 0.67 PP+ 0.67 LS+
536 340 2061 0
Note:- As per Cl 2.8.5 Br
UNFACTORED- - TRANSVERSE SEISMIC - COMB-2 Rule, HL/2 has been
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
17 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 703 298 1520 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
18 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 657 78 618 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
19 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 609 78 618 0
TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
20 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 657 78 618 0
0.67 TS+
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.34 LL2+ 0.67
21 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 TS+
525 298 1597 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
22 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
480 65 529 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
23 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
432 65 529 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
24 SP2+ 0.67 PP+ 0.67 PP+ 0.67 TS+
480 65 529 0
UNFACTORED- - WIND - COMB-2
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
25 LL1+ 0.34 LL2+ 0.67 Eph+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 703 298 1520 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
26 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 657 78 618 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 FPLL+ 0.67
27 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 0.67 609 78 618 0
WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 FPLL+
28 0.67 LL1+ 0.34 LL2+ 0.67 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 PP+ 657 78 618 0
0.67 WI
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 Eph+ 0.67
29 SP1+ 0.67 SP2+ 0.67 PP+ 0.67 WI
525 284 1432 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
30 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
480 65 529 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 HFL+ 0.67 SP1+ 0.67
31 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
432 65 529 0
0.67 DL1+ 0.67 DL2+ 0.67 SIDL + 0.67 LWL+ 0.67 SP1+ 0.67
32 SP2+ 0.67 PP+ 0.67 PP+ 0.67 WI
480 65 529 0
UNFACTORED- - COMB-3
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
33 Eph+ 1 SP1+ 1 SP2+ 1 PP+
1049 464 2509 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
34 SP1+ 1 SP2+ 1 PP+ 1 PP+
981 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
35 SP1+ 1 SP2+ 1 PP+ 1 PP+
910 136 1161 0

Design of Substructure for Br. No. 395 37 of 218

Br NO 395-R2 AN1
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
36 SP1+ 1 SP2+ 1 PP+ 1 PP+
981 136 1161 0

37 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 784 424 2137 0

38 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0

39 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 645 96 789 0

40 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0
Summary of UNFACORED Combination
1 Governing - Max. Axial load 1049 464 0 2509 0
9 Governing - Max. Long. Moment 758 573 0 3052 0
1 Governing - Max. Trans. moment 1049 464 0 2509 0
23 Governing - Min Vertical 432 65 0 529 0
SLS Combination
SLS - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
1 LL2+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
1075 468 2546 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
2 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
1008 140 1198 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
3 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
936 140 1198 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
4 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
1008 140 1198 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
5 PP+
784 424 2137 0

6 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0

7 1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 645 96 789 0

8 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 716 96 789 0
Permanent Load
9 1 DL1+ 1 DL2+ 1.2 SIDL + 669 0 for crack width
-30 0
Live Load for crack
10 1 FPLL+ 1 LL1+ 1 LL2+ 265 40 width
372 0
Note:- As per Cl 2.8.5 Br
SLS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
9 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LS+
1132 856 4552 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
10 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
1064 528 3205 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
11 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
993 528 3205 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
12 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
1064 528 3205 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
13 PP+ 1 LS+
867 835 4424 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
14 1 LS+
800 508 3076 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
15 1 LS+
728 508 3076 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
16 1 LS+
800 508 3076 0
Note:- As per Cl 2.8.5 Br
SLS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
17 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 TS+
1049 444 2266 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
18 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
981 116 918 0

Design of Substructure for Br. No. 395 38 of 218

Br NO 395-R2 AN1
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
19 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
910 116 918 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
20 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
981 116 918 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
21 PP+ 1 TS+
784 424 2137 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
22 1 TS+
716 96 789 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
23 1 TS+
645 96 789 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
24 1 TS+
716 96 789 0
SLS- - WIND - COMB-2
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
25 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 WI
1049 444 2266 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
26 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
981 116 918 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
27 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
910 116 918 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
28 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
981 116 918 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
29 PP+ 1 WI
784 424 2137 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
30 1 WI
716 96 789 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
31 1 WI
645 96 789 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
32 1 WI
716 96 789 0
SLS- - LWR- COMB-3
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
33 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LW+
1049 464 2509 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
34 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
981 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
35 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
910 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
36 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
981 136 1161 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
37 1 LW+
784 424 2137 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
38 LW+
716 96 789 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
39 LW+
645 96 789 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
40 LW+
716 96 789 0
Summary of SLS Combination
9 Governing - Max. Axial load 1132 856 0 4552 0
9 Governing - Max. Long. Moment 1132 856 0 4552 0
1 Governing - Max. Trans. moment 1075 468 0 2546 0
10 Governing - Min Vertical 265 Live40
Load for crack width 372 0
ULS Combination
ULS - -BASIC- COMB-1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
1 LL1+ 1.75 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
1515 791 4302 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
2 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1368 234 2011 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
3 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1278 234 2011 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
4 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1368 234 2011 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
5 1.7 SP2+ 1.7 PP+
1064 721 3646 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
6 1.7 PP+ 1.7 PP+
917 164 1355 0

Design of Substructure for Br. No. 395 39 of 218

Br NO 395-R2 AN1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
7 1.7 PP+ 1.7 PP+
828 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
8 1.7 PP+ 1.7 PP+
917 164 1355 0
Note:- As per Cl 2.8.5 Br
ULS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
9 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 LS+
1531 1263 6688 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
10 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1384 706 4397 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
11 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1295 706 4397 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
12 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
1384 706 4397 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
13 1.7 SP2+ 1.7 PP+ 1.25 LS+
1168 1235 6504 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
14 1.7 PP+ 1.7 PP+ 1.25 LS+
1021 678 4214 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
15 1.7 PP+ 1.7 PP+ 1.25 LS+
932 678 4214 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
16 1.7 PP+ 1.7 PP+ 1.25 LS+
1021 678 4214 0
Note:- As per Cl 2.8.5 Br
ULS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
17 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 TS+
1427 749 3829 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
18 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
1280 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
19 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
1191 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
20 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
1280 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
21 1.7 SP2+ 1.7 PP+ 1.25 TS+
1064 721 3646 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
22 1.7 PP+ 1.7 PP+ 1.25 TS+
917 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
23 1.7 PP+ 1.7 PP+ 1.25 TS+
828 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
24 1.7 PP+ 1.7 PP+ 1.25 TS+
917 164 1355 0
ULS- - WIND - COMB-2
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
25 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 WI
1427 749 3829 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
26 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
1280 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
27 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
1191 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
28 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
1280 192 1539 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
29 1.7 SP2+ 1.7 PP+ 1.25 WI
1064 721 3646 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
30 1.7 PP+ 1.7 PP+ 1.25 WI
917 164 1355 0

Design of Substructure for Br. No. 395 40 of 218

Br NO 395-R2 AN1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
31 1.7 PP+ 1.7 PP+ 1.25 WI
828 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
32 1.7 PP+ 1.7 PP+ 1.25 WI
917 164 1355 0
ULS- - COMB-3
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
33 LL1+ 1 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
1427 761 3975 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
34 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1280 204 1685 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
35 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1191 204 1685 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
36 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
1280 204 1685 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
37 1.7 SP2+ 1.7 PP+
1064 721 3646 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
38 1.7 PP+ 1.7 PP+
917 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
39 1.7 PP+ 1.7 PP+
828 164 1355 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
40 1.7 PP+ 1.7 PP+
917 164 1355 0
Summary of ULS Combination
9 Governing - Max. Axial load 1531 1263 0 6688 0
9 Governing - Max. Long. Moment 1531 1263 0 6688 0
1 Governing - Max. Trans. moment 1515 791 0 4302 0
7 Governing - Min Vertical 828 164 0 1355 0

Checking at Section TOP OF FOUNDATION

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 25 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 25 mm
Spacing in second layer 100 mm c/c
Dia of spacer bar 0 mm
dia of link 12 mm
long. Spacing (max= 1863 mm) 300 mm
No. of legs 6 nos
Reinf. diam. in first layer dbm = 20 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 2000 mm
Average Overall depth of the section ( In Tapering Section) hav = 2000 mm
Clear cover to Ast Cc = 75 mm

Design of Substructure for Br. No. 395 41 of 218

Br NO 395-R2 AN1

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) -30 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 372 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 4552
ULS-Total Moment 6688 kN-m
Ultimate Limit State Shear Vu = 1263 kN
Ultimate Limit State Torsion, Tu 10 kN-m

Other Inputs

Allowable crack width 0.20 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) TOP OF FOUNDATION

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 9817.48 3726.00 OK
2 ULS Moment resistance KN-m 6687.81 7297.29 OK
3 Crack Width mm 0.02 0.20 OK
4 Stress in Steel Mpa 271.65 375.00 OK
5 Stress in Concrete Mpa 11.39 17.50 OK
6 Area of Shear Reinforcement mm2 678.58 554.48 OK
7 Torsional Shear Stress and Capacity Mpa 0.69 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.91 0.38 OK
9 Secondary Reinforcement mm2 3140.00 2235.60 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 3726.00 mm2
As provided = 9817.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for two layers d= 1863.0 mm
CG of reinforcements, dc 112.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 10
Reinf. steel area provided, As = 4908.74 + 4909 9817.5 mm2
Reinf. steel area provided, Ast (flexure) 9817.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1708.7 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 7297 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1975 mm

Design of Substructure for Br. No. 395 42 of 218

Br NO 395-R2 AN1
Depth of Neutral axis NA, x= 468.09 mm
Distance from to the surface of the nearest longitudinal bar acr = 77.22 mm
Calculated strain in the tension reinforcement es = 0.000102
Strain at cracking LVL- Without stiffening Eff e1 = 0.0001 @cnom
Strain at cracking LVL- With stiffening Eff ets = -0.086267
Strain at cracking LVL- With stiffening Eff em = 0.0001 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.870E+11 mm4
Crack Width W cr = 0.0247 < 0.2 mm OK Tab-10
Stress in Steel fs = 20.4202 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -0.8566 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 4552.27 KN-m

Stress in Steel fs = 271.65 Mpa
Permissible Stress in Steel 0.75fy = 375.00 OK Tab-11
Stress in Concrete fs = 11.39 Mpa
Permissible Stress in Concrete 0.5fck = 17.50 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1.00
depth factor, xs = 0.72
vc = 0.216*(pt)1/3 *min(fc,40)1/3 0.57 MPa
vc' = xs vc (2d/av) = 0.41 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 332.36 mm2
v > vc', hence Asv reqd = 554.48 mm2
Asv prov 678.58 mm2
v = Vu / (bd) 0.68 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 554.48 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.00 mm
Smaller Core Dim of Section x1min = 838.00 mm
Longer Outer Dim of Section h max = 2000.00 mm
Longer Core Dim of Section y1max = 1838.00 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0120 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required

v + vt = 0.690 MPa < 4.43 MPa Torsional Capacity is OK

Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 2.8 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 490.87 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.00 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 113.10 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 300.00 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.91 > 0.38 OK
Longitudinal Reinforcement provided is OK

Design of Substructure for Br. No. 395 43 of 218

Br NO 395-R2 AN1
Secondary Steel on Compression face STATUS OK
Eff. depth of the section 'd' for two layers d= 1863.00 mm
Width of Section b= 1000.00 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 2235.60 mm2
Area of reinforcement Provided = 3140 + 0 3140.00 mm2

Bottom Of Foundation

CALCULATIONS FOR LOADING

Vertic Hzl. -
ML MT
SYM al X ECC
Sl. No Description
LA
KN KN m m KN-m KN-m
BASIC LOADS
0 0 0 0 0.000 0 0
1 DEAD LOADS
1a Super Str DL DL1+ 57 5.07 288.0
1b Self Weight DL2+ 2022.0 3.94 7960
1c Super Imposed Dead Load SIDL + 55.4 5.07 280.6
1d Buoyant Force-HFL HFL+ -304.6 0.0
1e Buoyant Force-LWL LWL+ -154.6 0.0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 50.0 5.07 253.4
2b Live Load LL1+ 215 5.07 1088.6
2c Long Load LL2+ 40 13.716 550.4
3 Earth Pressure
3a Earth Pressure Eph+ 176.65 407.25 0.00 4.735 1928.5
3b Surcharge Pressure -1 SP 1+ 41.19 94.949 0.00 7.103 674.4
3c Surcharge Pressure-2 SP2+ 11.37 26.20 0.00 12.589 329.9
3d Passive Resistance PP+ -59.52 0.833 -49.60
4 Seismic Force
4a Long Seismic - (LS) + LS+ 0 730 5577
4b Trans Seismic - (TS + TS+ 0 0 0 0
5 LWR FORCE
5a LWR FORCE + LW+ 0 13.72 0
6 Force Due To WIND
6a WIND+ WI 0 0 0 0
COMBINATION LOADS
1 2 3 4 5 6 7 8 9 10 11 12 13
SR No Description V HL ML MT
UNFACTORED - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
2324 509 13304 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
2 SP1+ 1 SP2+ 1 PP+ 1 PP+
2297 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
3 SP1+ 1 SP2+ 1 PP+ 1 PP+
2147 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
4 SP1+ 1 SP2+ 1 PP+ 1 PP+
2297 42 11326 0

5 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 2059 469 11412 0

6 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2032 2 9434 0

7 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1882 2 9434 0

8 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2032 2 9434 0

Design of Substructure for Br. No. 395 44 of 218

Br NO 395-R2 AN1
Note:- As per Cl 2.8.5 Br
UNFACTORED- - LONG SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
9 0.4 LL2+ 0.8 Eph+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 LS+
1859 975 14885 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
10 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 LS+
1838 602 13303 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
11 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 LS+
1718 602 13303 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
12 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 LS+
1838 602 13303 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 Eph+ 0.8 SP1+
13 0.8 SP2+ 0.8 PP+ 0.8 LS+
1647 959 13591 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
14 0.8 PP+ 0.8 PP+ 0.8 LS+
1626 586 12009 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 SP1+ 0.8 SP2+
15 0.8 PP+ 0.8 PP+ 0.8 LS+
1506 586 12009 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
16 0.8 PP+ 0.8 PP+ 0.8 LS+
1626 586 12009 0
Note:- As per Cl 2.8.5 Br
UNFACTORED- - TRANSVERSE SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
17 0.4 LL2+ 0.8 Eph+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 TS+
1859 391 10423 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
18 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 TS+
1838 18 8841 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
19 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 TS+
1718 18 8841 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
20 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 TS+
1838 18 8841 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.4 LL2+ 0.8 Eph+
21 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 TS+
1647 391 9350 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
22 0.8 PP+ 0.8 PP+ 0.8 TS+
1626 2 7547 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 SP1+ 0.8 SP2+
23 0.8 PP+ 0.8 PP+ 0.8 TS+
1506 2 7547 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
24 0.8 PP+ 0.8 PP+ 0.8 TS+
1626 2 7547 0
UNFACTORED- - WIND - COMB-2
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
25 0.4 LL2+ 0.8 Eph+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 WI
1859 391 10423 0

0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
26 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 WI
1838 18 8841 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 FPLL+ 0.8 LL1+
27 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 WI
1718 18 8841 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 FPLL+ 0.8 LL1+
28 0.4 LL2+ 0.8 SP1+ 0.8 SP2+ 0.8 PP+ 0.8 PP+ 0.8 WI
1838 18 8841 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 Eph+ 0.8 SP1+
29 0.8 SP2+ 0.8 PP+ 0.8 WI
1647 375 9130 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
30 0.8 PP+ 0.8 PP+ 0.8 WI
1626 2 7547 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 HFL+ 0.8 SP1+ 0.8 SP2+
31 0.8 PP+ 0.8 PP+ 0.8 WI
1506 2 7547 0
0.8 DL1+ 0.8 DL2+ 0.8 SIDL + 0.8 LWL+ 0.8 SP1+ 0.8 SP2+
32 0.8 PP+ 0.8 PP+ 0.8 WI
1626 2 7547 0
UNFACTORED- - COMB-3

Design of Substructure for Br. No. 395 45 of 218

Br NO 395-R2 AN1
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
33 Eph+ 1 SP1+ 1 SP2+ 1 PP+
2324 509 13304 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
34 SP1+ 1 SP2+ 1 PP+ 1 PP+
2297 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
35 SP1+ 1 SP2+ 1 PP+ 1 PP+
2147 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
36 SP1+ 1 SP2+ 1 PP+ 1 PP+
2297 42 11326 0

37 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 2059 469 11412 0

38 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2032 2 9434 0

39 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1882 2 9434 0

40 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2032 2 9434 0
Summary of UNFACORED Combination
1 Governing - Max. Axial load 2324 509 0 13304 0
9 Governing - Max. Long. Moment 1859 975 0 14885 0
1 Governing - Max. Trans. moment 2324 509 0 13304 0
15 Governing - Min Vertical 1506 586 0 12009 0
SLS Combination
SLS - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
1 LL2+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
2361 513 13550 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
2 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
2334 46 11572 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1.1 FPLL+ 1.1 LL1+ 1.1
3 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
2184 46 11572 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1.1 FPLL+ 1.1 LL1+ 1.1
4 LL2+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
2334 46 11572 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
5 PP+
2070 469 11468 0

6 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2043 2 9490 0

7 1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1893 2 9490 0

8 1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 2043 2 9490 0
Permanent Load
9 1 DL1+ 1 DL2+ 1.2 SIDL + 1 Eph+ 1 SP1+ 1 SP2+ 2374 528 for crack width
11518 0
Live Load for crack
10 1 FPLL+ 1 LL1+ 1 LL2+ 265 40 width
1892 0
Note:- As per Cl 2.8.5 Br
SLS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
9 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LS+
2335 1219 18662 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
10 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2308 752 16684 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
11 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2158 752 16684 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
12 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2308 752 16684 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
13 PP+ 1 LS+
2070 1199 17045 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
14 1 LS+
2043 732 15067 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
15 1 LS+
1893 732 15067 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
16 1 LS+
2043 732 15067 0
Note:- As per Cl 2.8.5 Br
SLS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
17 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 TS+
2335 489 13085 0

Design of Substructure for Br. No. 395 46 of 218

Br NO 395-R2 AN1
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
18 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
2308 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
19 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
2158 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
20 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 TS+
2308 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
21 PP+ 1 TS+
2070 469 11468 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
22 1 TS+
2043 2 9490 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
23 1 TS+
1893 2 9490 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
24 1 TS+
2043 2 9490 0
SLS- - WIND - COMB-2
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
25 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 WI
2335 489 13085 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
26 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
2308 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
27 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
2158 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
28 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 WI
2308 22 11107 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1
29 PP+ 1 WI
2070 469 11468 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
30 1 WI
2043 2 9490 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
31 1 WI
1893 2 9490 0
1 DL1+ 1 DL2+ 1.2 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+
32 1 WI
2043 2 9490 0
SLS- - LWR- COMB-3
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
33 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LW+
2324 509 13304 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
34 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
2297 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
35 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
2147 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
36 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LW+
2297 42 11326 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
37 1 LW+
2059 469 11412 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
38 LW+
2032 2 9434 0
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
39 LW+
1882 2 9434 0
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
40 LW+
2032 2 9434 0
Summary of SLS Combination
9 Governing - Max. Axial load Permanent
2374 528 Load for crack width
11518 0
9 Governing - Max. Long. Moment 2335 1219 0 18662 0
1 Governing - Max. Trans. moment 2361 513 0 13550 0
10 Governing - Min Vertical 265 Live40
Load for crack width 1892 0
ULS Combination
ULS - -BASIC- COMB-1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
1 LL1+ 1.75 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
3169 867 19021 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
2 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
3056 74 15659 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.5 FPLL+ 1.75
3 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
2869 74 15659 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.5 FPLL+ 1.75
4 LL1+ 1.75 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
3056 74 15659 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
5 1.7 SP2+ 1.7 PP+
2718 797 15773 0

Design of Substructure for Br. No. 395 47 of 218

Br NO 395-R2 AN1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
6 1.7 PP+ 1.7 PP+
2605 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
7 1.7 PP+ 1.7 PP+
2418 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
8 1.7 PP+ 1.7 PP+
2605 4 12410 0
Note:- As per Cl 2.8.5 Br
ULS - LONG SEISMIC- COMB-2 Rule, HL/2 has been
Considered with Seismic

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
9 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 LS+
3081 1738 24970 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
10 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
2969 945 21608 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
11 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
2781 945 21608 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
12 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 LS+
2969 945 21608 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
13 1.7 SP2+ 1.7 PP+ 1.25 LS+
2718 1710 22744 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
14 1.7 PP+ 1.7 PP+ 1.25 LS+
2605 916 19382 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
15 1.7 PP+ 1.7 PP+ 1.25 LS+
2418 916 19382 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
16 1.7 PP+ 1.7 PP+ 1.25 LS+
2605 916 19382 0
Note:- As per Cl 2.8.5 Br
ULS - TRANSVERSE SEISMIC- LWL- COMB-2 Rule, HL/2 has been
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
17 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 TS+
3081 825 17999 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
18 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
2969 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
19 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
2781 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
20 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 TS+
2969 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
21 1.7 SP2+ 1.7 PP+ 1.25 TS+
2718 797 15773 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
22 1.7 PP+ 1.7 PP+ 1.25 TS+
2605 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
23 1.7 PP+ 1.7 PP+ 1.25 TS+
2418 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
24 1.7 PP+ 1.7 PP+ 1.25 TS+
2605 4 12410 0
ULS- - WIND - COMB-2
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
25 LL1+ 0.7 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.25 WI
3081 825 17999 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
26 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
2969 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
27 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
2781 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
28 LL1+ 0.7 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+ 1.25 WI
2969 32 14636 0

1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
29 1.7 SP2+ 1.7 PP+ 1.25 WI
2718 797 15773 0

Design of Substructure for Br. No. 395 48 of 218

Br NO 395-R2 AN1
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
30 1.7 PP+ 1.7 PP+ 1.25 WI
2605 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
31 1.7 PP+ 1.7 PP+ 1.25 WI
2418 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
32 1.7 PP+ 1.7 PP+ 1.25 WI
2605 4 12410 0
ULS- - COMB-3
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
33 LL1+ 1 LL2+ 1.7 Eph+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+
3081 837 18164 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
34 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
2969 44 14802 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.25 FPLL+ 1.4
35 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
2781 44 14802 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.25 FPLL+ 1.4
36 LL1+ 1 LL2+ 1.7 SP1+ 1.7 SP2+ 1.7 PP+ 1.7 PP+
2969 44 14802 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 Eph+ 1.7 SP1+
37 1.7 SP2+ 1.7 PP+
2718 797 15773 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
38 1.7 PP+ 1.7 PP+
2605 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 HFL+ 1.7 SP1+ 1.7 SP2+
39 1.7 PP+ 1.7 PP+
2418 4 12410 0
1.25 DL1+ 1.25 DL2+ 2 SIDL + 1.25 LWL+ 1.7 SP1+ 1.7 SP2+
40 1.7 PP+ 1.7 PP+
2605 4 12410 0
Summary of ULS Combination
1 Governing - Max. Axial load 3169 867 0 19021 0
9 Governing - Max. Long. Moment 3081 1738 0 24970 0
1 Governing - Max. Trans. moment 3169 867 0 19021 0
7 Governing - Min Vertical 2418 4 0 12410 0

Extra Load on Transverse Projected Part of Footing

Length of Footing 11.00 m

Length of Toe 4.50 m
Width of Footing - In Transeverse Direction = 7.85 m
Extra Width of Footing 7.85 m
Thickness of Foundation 1.60 m
Soil Depth Over Heel 12.606 m
Soil Depth Over Toe 1.400 m
Wt. of Footing - 11.00 x 7.85 x 1.60 x 25 = 3454 KN
Wt. of Soil over Heel 6.50 x 7.85 x 12.61 x 18 = 11578 KN
Wt of Soil Over Toe 4.50 x 7.85 x 1.40 x 18 = 890.2 KN
Total Extra Vertical Load = 15922 KN
Extra Seismic Force

Horz Seismic Coff 0.18

Vert Seismic Coff 0.12

Extra Horz Seismic Force = 0.18 x 15922 = 2866 KN

Extra Vert Seismic Force = 0.12 x 15922 = 1911 KN

Design of Substructure for Br. No. 395 49 of 218

Br NO 395-R2 AN1

Analysis of Foundation Pressure ( For Open Foundation )

X
Area = A = 11.000 x 7.850 = 86.35 m2

Zxx = 7.850 x 11.000 2

= 158.31 m3
6

7.850

Y
Y

ZYY = 11.000 x 7.850 2

= 112.97 m3
6

2
11.000 SBC = 470.0 KN/m ( For Normal Condition )

Allowable Eccentricity = b / 4.00

X
Allowable eL = 11.000 / 4 = 2.75 m 2.508 m OK
Allowable eT = 7.850 / 4 = 1.963 m 0.000 m OK

Unfactored Load Table

Pressure Calculation at Bottom of Foundation

Safe Bearing Capacity = 470.000 KN/m2

Vert. Momen Result e (m) Pmax (t/m2) Pmin (t/m2)

Load t (t-m) ant
(t) from B (m) Result
Governing Load case
End -
R (m)
Sr No V M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B)
1 Max Axial Load 2324 13304 5.7 11.0 0.2 237.3 185.20 OK
2 Max Long Moment 1859 14885 8.0 2.5 400.1 -62.16 REDIST
3 Max Transverse Mo 2324 13304 5.7 0.2 237.3 185.20 OK
4 Min Vert Load 1506 12009 8.0 2.5 321.7 -47.96 REDIST

Load
Case eL Pmax = 4*P
eT L' = L - B' =B - Eff Area A' =
P 2 eL 2 eT L'*B' / 3*A' CHK
1 0.23 0.00 2323.5 10.55 7.85 82.8027 37.5 OK
2 2.51 0.00 1858.8 5.985 7.85 46.9787 52.8 OK
3 0.23 0.00 2323.5 10.55 7.85 82.8027 37.5 OK
4 2.48 0.00 1505.7 6.049 7.85 47.4809 33.9 OK
52.8 OK
Over All Result = OK

Pressure Distribution Along the Length of Foundation

Toe Length T 4.50 m

Heel Projection H 4.50 m
Total Width of Footing L 11.000 m

Design of Substructure for Br. No. 395 50 of 218

Br NO 395-R2 AN1

Pressure at Pressure at
Pmax Pmin Pmax-Pmin ( Change / unit Jn of Toe & Jn of Heel &
KN/m2 KN/m2 KN/m2) Length Abt Abt
Sr No 1 2 3 4 ( 3/ L) 1-(4*T) 2+(4*H)
1 237 185 52 5 216 206
2 400 -62 462 42 211 127
3 237 185 52 5 216 206
4 322 -48 370 34 170 103

SLS Load Checking- For Crack Width Calculation

Governing Load case

Sr No
1 For Permanent Load 2374 11518 4.9 11.0 0.0 215.9 215.86
2 For Live Load Only 265 1892 7.1 1.6 45.7 2.45

Pressure Distribution Along the Length of Foundation

Pressure at Pressure at
Pmax Pmin Pmax-Pmin ( Change / unit Jn of Toe & Jn of Heel &
KN/m2 KN/m2 KN/m2) Length Abt Abt
Sr No 1 2 3 4 ( 3/ L) 1-(4*T) 2+(4*H)
1 216 216 0 0 216 216
2 46 2 43 4 28 20

SLS- For Stress Check

Vert. Momen Result e (m) Pmax (t/m2) Pmin (t/m2)

Load t (t-m) ant
(t) from B (m)
Governing Load case End -
R (m)
ML
Sr No V-KN KN-m M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B)
1 Max Axial Load 2374 11518 4.9 11.0 0.0 215.9 215.86
2 Max Long Moment 2335 18662 8.0 2.5 500.9 -76.46
3 Max Transverse Mo 2361 13550 5.7 0.2 242.6 186.69
4 Min Vert Load 265 1892 7.1 1.6 45.7 2.45

Pressure Distribution Along the Length of Foundation

Pressure at Pressure at
Pmax Pmin Pmax-Pmin ( Change / unit Jn of Toe & Jn of Heel &
KN/m2 KN/m2 KN/m2) Length Abt Abt
Sr No 1 2 3 4 ( 3/ L) 1-(4*T) 2+(4*H)
1 216 216 0 0 216 216
2 501 -76 577 52 265 160
3 243 187 56 5 220 210
4 46 2 43 4 28 20

ULS- Check for Reinforcement

Design of Substructure for Br. No. 395 51 of 218

Br NO 395-R2 AN1
Vert. Momen Result e (m) Pmax (t/m2) Pmin (t/m2)
Load t (t-m) ant
(t) from B (m)
Governing Load case End -
R (m)
ML
Sr No V-KN KN-m M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B)
1 Max Axial Load 3169 19021 6.0 0.5 367.0 209.16
2 Max Long Moment 3081 24970 8.1 2.6 678.0 -117.72
11.0
3 Max Transverse Mo 3169 19021 6.0 0.5 367.0 209.16
4 Min Vert Load 2418 12410 5.1 0.0 219.8 219.80

Pressure Distribution Along the Length of Foundation- ULS Condition

Pressure at Pressure at
Pmax Pmin Pmax-Pmin ( Change / unit Jn of Toe & Jn of Heel &
KN/m2 KN/m2 KN/m2) Length Abt Abt
Sr No 1 2 3 4 ( 3/ L) 1-(4*T) 2+(4*H)
1 367 209 158 14 302 274
2 678 -118 796 72 352 208
3 367 209 158 14 302 274
4 220 220 0 0 220 220

Design of Toe

Toe Projection 4.50 m

End Thickness of Toe 0.50 m
Thickness at Face of Abutment 1.60 m
Average Thickness =(0+0)/2= 1.05 m
Weight of Toe/ Length =0x25= 26.25 Kn/m
Total weight of Toe =0x0= 118.13 KN
Moment due to Self Wt =0x0x0/2= 265.78 Km-m ( Unfactored)

Note:- Soil over Toe has been ignored on safer side

SLS CHK
At Abt Jn At End Average Shear Moment
Sr No Load Case
KN/m2 KN/m2 KN/m2 KN KN-m
For Crack Width Calculation
1 Permanent Load 216 216 216 971 2186
2 Live Load 28 46 37 166 373
For Stress Check
3 Max Axial Load 216 216 216 971 2186
4 Max Long Moment 265 160 212 955 2149
5 Max Transverse Mo 220 210 215 966 2173
6 Min Vert Load 28 20 24 108 244
Max 971 2186

Summary of SLS -Output

Moment due to Permanent Load = 2185.57 - 265.78 = 1919.79 KN-m

Moment due to Live Load = = 373 KN-m
Max SLS Moment - For Stress Check 2185.57 - 265.78 = 1919.79 KN-m

Design of Substructure for Br. No. 395 52 of 218

Br NO 395-R2 AN1
ULS CHK
At Abt Jn At End Average Shear Moment
Sr No Load Case
KN/m2 KN/m2 KN/m2 KN KN-m
Max Axial Load 302 367 335 1506 3389
Max Long Moment 352 678 515 258 64
Max Transverse Mo 302 367 335 536 428
Min Vert Load 220 220 220 231 121
Max 1506 3389

Summary of SLS -Output

Max ULS Moment 3389.18 - 332.23 = 3056.96 KN-m

Max ULS Shear 1506.30 - 147.66 = 1358.65 KN-m

Checking at Section TOE

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 12 mm
long. Spacing (max= 1490 mm) 200 mm
No. of legs 8 nos
Reinf. diam. in first layer dbm = 12 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Average Overall depth of the section ( In Tapering Section) hav = 1050 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 1919.79 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 373 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 1919.79
ULS-Total Moment 3056.96 kN-m
Ultimate Limit State Shear Vu = 1359 kN
Ultimate Limit State Torsion, Tu 10.0 kN-m

Design of Substructure for Br. No. 395 53 of 218

Br NO 395-R2 AN1
Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) TOE

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3056.96 4770.59 OK
3 Crack Width mm 0.125 0.25 OK
4 Stress in Steel Mpa 175.01 375.00 OK
5 Stress in Concrete Mpa 7.44 17.5 OK
6 Area of Shear Reinforcement mm2 904.78 484.1 OK
7 Torsional Shear Stress and Capacity Mpa 0.928 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1130 1128.00 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2980.00 mm2
As provided = 8042.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1490.0 mm
CG of reinforcements, dc 78.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1363.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4771 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 378.23 mm
Distance from to the surface of the nearest longitudinal bar acr = 76.65 mm
Calculated strain in the tension reinforcement es = 0.001045
Strain at cracking LVL- Without stiffening Eff e1 = 0.0011 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000583
Strain at cracking LVL- With stiffening Eff em = 0.0006 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 9.756E+10 mm4
Crack Width W cr = 0.1247 < 0.25 mm OK Tab-10

Design of Substructure for Br. No. 395 54 of 218

Br NO 395-R2 AN1

Stress in Steel fs = 209.03 < (0.75fy) 375 MPa OK Tab-11

Stress in Concrete fc = -8.89 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 1920 KN-m

Stress in Steel fs = 175.01 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 7.44 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.761
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.575 MPa
vc' = xs vc (2d/av) = 0.438 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 484.1 mm2
Asv prov 904.8 mm2
v = Vu / (bd) 0.912 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 484.1 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 888.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1488.0 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0158 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.928 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 2.18 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 113.1 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.57 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 940.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 1128 mm2
Area of reinforcement Provided = 1130 + 0 1130 mm2

Design of Heel
Heel Projection 4.50 m

Design of Substructure for Br. No. 395 55 of 218

Br NO 395-R2 AN1
Effective Heel Projection 4.50 m
End Thickness of Heel 0.50 m
Thickness at Face of Abutment 1.60 m
Average Thickness =(0+0)/2= 1.05 m
Height of Fill over Heel 12.61 m
Self weight Heel 26.25 KN/m
Weight of Soil over Heel 226.91 KN/m
Total Downward Weight of Heel/ Length =0+0= 253.16 KN/m
Total weight of Heel+Soil =0x0= 1139.21 KN
Moment due to Self Wt =0x0x0/2= 2563.22 KN-m ( Unfactored)

SLS CHK
At Abt Jn At End Average Shear Moment
Sr No Load Case
KN/m2 KN/m2 KN/m2 KN KN-m
For Crack Width Calculation
1 Permanent Load 216 216 216 971 2186
2 Live Load 20 2 11 51 114
For Stress Check
3 Max Axial Load 216 216 216 971 2186
4 Max Long Moment 160 -76 42 187 422
5 Max Transverse Mo 210 187 198 892 2006
6 Min Vert Load 20 2 11 51 114
Max 971 114

Summary of SLS -Output

Moment due to Permanent Load = 2563.22 - 2185.57 = 377.66 KN-m

Moment due to Live Load = = 114 KN-m
Max SLS Moment - For Stress Check 2563.22 - 114.39 = 2448.84 KN-m

ULS CHK
At Abt Jn At End Average Shear Moment
Sr No Load Case
KN/m2 KN/m2 KN/m2 KN KN-m
Max Axial Load 274 209 241 1087 2445
Max Long Moment 208 -118 45 23 6
Max Transverse Mo 274 209 241 386 309
Min Vert Load 220 220 220 231 121
Max 1087 6

Summary of ULS -Output

Max ULS Moment 5.63 - 3204.03 = 3198.40 KN-m

Max ULS Shear 1086.52 - 1424.01 = 337.49 KN

Transverse Analysis of Heel Raft

C/C of Retrun = 7.850 - 0.45 = 7.400 m

UDL of Soil Load = 226.91 KN/m

2
Sagging Moment = 226.91 x 7.400 = 1553 KN-m
8
Hoggoing Moment Due to Return = 6309 KN-m

Design of Substructure for Br. No. 395 56 of 218

Br NO 395-R2 AN1
Net Hogging Moment = 6309 - 1553 = 4756 KN-m

Checking at Section HEEL

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Reinf. diam. in Top Layer Transverse ( For RAFT) dbm = 32 mm
Reinf. diam. in Top Layer Transverse- 2nd Layer ( For Raft) 100 mm c/c
Dia of spacer bar 0 mm
dia of link 12 mm
long. Spacing (max= 1490 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Average Overall depth of the section ( In Tapering Section) hav = 1050 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 377.66 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 114 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 2448.84 kN-m
ULS-Total Moment 3198.40 kN-m
ULS-Total Moment- Transverse Direction 4755.96 kN-m
Ultimate Limit State Shear Vu = 337 kN
Ultimate Limit State Torsion, Tu 10.0 kN-m

Design of Substructure for Br. No. 395 57 of 218

Br NO 395-R2 AN1

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) HEEL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm 2
8042.48 2980.00 OK
2 ULS Moment resistance KN-m 3198.40 4770.59 OK
3 Crack Width mm 0.000 0.20 OK
4 Stress in Steel Mpa 223.24 375.00 OK
5 Stress in Concrete Mpa 9.49 17.5 OK
6 Area of Shear Reinforcement mm2 565.49 0.0 OK
7 Torsional Shear Stress and Capacity Mpa 0.242 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 2010 1128 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2980.00 mm2
As provided = 8042.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check- LONG DIRECTION STATUS OK

Eff. depth of the section 'd' for single layer d= 1490.0 mm
CG of reinforcements, dc 78.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1363.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4771 kN-m

Ultimate Limit State Check- TRANS DIRECTION STATUS OK

Eff. depth of the section 'd' for single layer d= 1490.0 mm
CG of reinforcements, dc 78.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1363.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4771 kN-m

Design of Substructure for Br. No. 395 58 of 218

Br NO 395-R2 AN1

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 378.23 mm
Distance from to the surface of the nearest longitudinal bar acr = 76.65 mm
Calculated strain in the tension reinforcement es = 0.000224
Strain at cracking LVL- Without stiffening Eff e1 = 0.0002 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.002350
Strain at cracking LVL- With stiffening Eff em = -0.0021 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
4
Moment of Inertia I 9.756E+10 mm
Crack Width W cr = 0.0000 < 0.2 mm OK Tab-10
Stress in Steel fs = 44.86 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete f c = -1.91 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 2449 KN-m

Stress in Steel fs = 223.24 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 9.49 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.761
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.575 MPa
vc' = xs vc (2d/av) = 0.438 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 0.0 mm2
Asv prov 565.5 mm2
v = Vu / (bd) 0.227 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 104.5 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 888.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1488.0 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0158 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.242 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 2.18 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2

Design of Substructure for Br. No. 395 59 of 218

Br NO 395-R2 AN1

Area of Shear reinforcement ( Outer Layer) Asv = 113.1 mm2

Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.57 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 940.0 mm
Width of Section b= 1000.0 mm
2
Area of Secondary reinforcement require - on either side @ 0.12 % 1128 mm
2
Area of reinforcement Provided = 2010 + 0 2010 mm

Transverse Analysis of Heel In Case of Raft

C/C of Return in Transverse Direction 7.350 m

Hogging Moment from Return/ m Length 2516.40 KN-m
Depth of Fill over Heel 12.61 m
3
Density of Fill 18.00 KN/m
Sagging Moment due to Fill =0x0x0x0/8= 1532.267179 KN-m
Net Moment =0-0= 984.13 KN-m
Ultimate Moment ( Taking Factor 1.7 as Earth Load is Dominating) 1673 KN-m

Checking at Section HEEL- Transverse Dir

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 110 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 100 mm c/c
Dia of spacer bar 0 mm

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

ULS-Total Moment 1673.02 kN-m

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 3100.00 mm2
As provided = 7238.23 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Design of Substructure for Br. No. 395 60 of 218

Br NO 395-R2 AN1

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1490.0 mm
CG of reinforcements, dc 78.0 mm
Number of reinforcing bars, Nb 9.0
Number of reinforcing bars, Nb 10
Reinf. steel area provided, As = 7238.23 + 0 7238.2 mm2
Reinf. steel area provided, Ast (flexure) 7238.2 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1376.3 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4333 kN-m

STABILITY CALCULATION
Width of Footing = 11.00 m
Eccentricity from Front will subtracted from above value

CALCULATIONS FOR LOADING

Restor Overt
Vertic Hzl. - ing urning
al X ECC Mome Mome
Sl. No Description SYM
nt nt
LA MR MO
KN KN m m KN-m KN-m
BASIC LOADS
0 0 0 0 0.000 0 0
1 DEAD LOADS
1a Super Str DL DL1+ 57 5.93 337
1b Self Weight DL2+ 2022 7.06 14281
1c Super Imposed Dead Load SIDL + 55 5.93 328
1d Buoyant Force-HFL HFL+ -305 0.00 0
1e Buoyant Force-LWL LWL+ -155 0.00 0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 50 5.93 297
2b Live Load LL1+ 215 5.93 1274
2c Long Load LL2+ 40 13.716 550
3 Earth Pressure
3a Earth Pressure Eph+ 407 4.735 1928.5
3b Surcharge Pressure -1 SP1+ 95 7.103 674.42
3c Surcharge Pressure-2 SP2+ 26 12.589 329.88
3d Passive Resistance PP+ -60 0.833 -49.60
4 Seismic Force
4a Long Seismic - (LS) + LS+ 0 730 0 0
4b Trans Seismic - (TS + TS+ 0 0 0 0 0
5 LWR FORCE
5a LWR FORCE + LW+ 0 13.716 0
6 Force Due To WIND
6a WIND+ WI 0 0 0

Design of Substructure for Br. No. 395 61 of 218

Br NO 395-R2 AN1

COMBINATION LOADS
1 2 3 4 5 6 7
8 9 10 11 12 13
SR No Description V HL MR MO
UNFACTORED - -BASIC- COMB-1
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
2094 509 16518 3434
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
2 SP1+ 1 SP2+ 1 PP+ 1 PP+
2244 42 16518 1455
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
3 SP1+ 1 SP2+ 1 PP+ 1 PP+
2094 42 16518 1455
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 1 LL2+ 1
4 SP1+ 1 SP2+ 1 PP+ 1 PP+
2244 42 16518 1455

5 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1830 469 14947 2883

6 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1980 2 14947 905

7 1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1830 2 14947 905

8 1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1980 2 14947 905
Note:- As per Cl 2.8.5 Br
UNFACTORED- - LONG SEISMIC - COMB-2 Rule, HL/2 has been
Considered with Seismic
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
9 Eph+ 1 SP1+ 1 SP2+ 1 PP+ 1 LS+
2094 1219 16518 3158
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
10 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2244 752 16518 1180
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
11 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2094 752 16518 1180
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 FPLL+ 1 LL1+ 0.5 LL2+ 1
12 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1 LS+
2244 752 16518 1180
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 Eph+ 1 SP1+ 1 SP2+ 1 PP+
13 1 LS+
1830 1199 14947 2883
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
14 LS+
1980 732 14947 905
1 DL1+ 1 DL2+ 1 SIDL + 1 HFL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
15 LS+
1830 732 14947 905
1 DL1+ 1 DL2+ 1 SIDL + 1 LWL+ 1 SP1+ 1 SP2+ 1 PP+ 1 PP+ 1
16 LS+
1980 732 14947 905

13 Against Overturning (Sub Structure Code Clause 5.10.1.1 and 6.8 )

FOS
Restoring moment Overturning moment Factor of Safety (Reqd.
CASE (R) (O) (R/O) ) Result
1 16517.6 3433.5 4.8 2.0 OK
2 16517.6 1455.5 11.3 2.0 OK
Normal Case

3 16517.6 1455.5 11.3 2.0 OK

4 16517.6 1455.5 11.3 2.0 OK
5 14946.8 2883.1 5.2 2.0 OK
6 14946.8 905.1 16.5 2.0 OK
7 14946.8 905.1 16.5 2.0 OK
8 14946.8 905.1 16.5 2.0 OK
9 16517.6 3158.3 5.2 1.5 OK
10 16517.6 1180.3 14.0 1.5 OK
Seismic Case

11 16517.6 1180.3 14.0 1.5 OK

12 16517.6 1180.3 14.0 1.5 OK
13 14946.8 2883.1 5.2 1.5 OK
14 14946.8 905.1 16.5 1.5 OK
15 14946.8 905.1 16.5 1.5 OK

Design of Substructure for Br. No. 395 62 of 218

Br NO 395-R2 AN1

16 14946.8 905.1 16.5 1.5 OK

13 Against Sliding (Sub Structure Code Clause 6.8 )

Width Passiv
Coeff. Cohes Factor
of e Resisting FOS
Vertical of ion, c Horizontal of
CASE footin Force, Force, R (KN) (Reqd Result
Force (W) Frictio (KN/ # Force, S (KN) Safety
2 g, B Pp .)
n, m m) (R/S)
(m) (KN)
1 2094.342 1840.080 509.004 3.6 1.50 OK
2 2244.391 1960.119 42.234 46.4 1.50 OK
3 2094.342 1840.080 42.234 43.6 1.50 OK
4 2244.391 1960.119 42.234 46.4 1.50 OK
5 1829.541 1628.239 468.877 3.5 1.50 OK
6 1979.590 1748.279 2.107 829.8 1.50 OK
7 1829.541 1628.239 2.107 772.8 1.50 OK
10.000

11.000

8 1979.590 54.606 1748.279 2.107 829.8 1.50 OK

0.800

9 2094.342 1840.080 1219.227 1.5 1.25 OK

10 2244.391 1960.119 752.457 2.6 1.25 OK
11 2094.342 1840.080 752.457 2.4 1.25 OK
12 2244.391 1960.119 752.457 2.6 1.25 OK
13 1829.541 1628.239 1199.163 1.4 1.25 OK
14 1979.590 1748.279 732.394 2.4 1.25 OK
15 1829.541 1628.239 732.394 2.2 1.25 OK
16 1979.590 1748.279 732.394 2.4 1.25 OK

#
( Resisting Force, R = m W+Bc+P p )
OVERALL CHECK In Overturning OK In Sliding OK

Design of Substructure for Br. No. 395 63 of 218

Br NO 395-R2 AN1
Abutment CAP

Summary of Loading ( Bearing Load as per Calculation Above)

Beari
DL SIDL FPLL LL-V LL-H Seismic-KN Ecc from C/L of Pier-m
ng
No KN KN KN KN KN HL HT V eL eT
B1 223.0 217.34 50.00 539 315 0.0 0.0 48.3 0.00 0.00
B2 223.0 217.34 50.00 539 315 0.0 0.0 48.3 0.00 0.00

Calculation for Width of Distribution

Assumptions
1- Load From Pedestal ( Or Bearing if No Pedestal) is assumed to disperse 0.5H:1V
2- Dispersion Should be calculated up to CG of Abutment Cap
3- Extra raising of Abutment Cap due to non similar Super Str has been ignored

Description Left Span Unit

Depth of Cap at Abutment face 0.500 m
Depth of Cap at End 0.500 m
Pedestal - Along 0.513 m
Pedestal - Across 0.002 m
Bearing Trans Distance from C/L of Abutment 1.800 m
Depth of Cap at bearing Location 0.500 m
Width of Across Distribution under Pedestal 0.502 m

Description Along Unit

Length of Abutment Cap 1.000 m
Overhang 0.000 m
Shear due to Self Wt. of Overhang- /m width 0.000 KN
Moment due to Self Wt. of Overhang- /m width 0.000 KN-m

Along Analysis

Along Moment due to Self Wt 0.000 KN-m ( Will be added to DL Moment below)
Along Shear due to Self Wt 0.000 KN-m ( Will be added to DL Shear below)

Width of Distribution = 0.502 m

Moment For Unit Width Due to ---

Beari DL SIDL FPLL LL-V Seismic
ng KN-m KN-m KN-m KN-m KN-m
B1 0.0 0.00 0.00 0.00 0.00
B2 0.0 0.00 0.00 0.00 0.00

SLS -Combination- For Stress Check

Beari DL SIDL FPLL LL-V Seismic SLS Moment-

ng Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1 0.0 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 0.0
B2 1 0.0 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 0.0
Maximum 0.0

ULS -Combination- For RCC Design

Beari DL SIDL FPLL LL-V Seismic ULS Moment-

ng Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1.25 0.0 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 0.0
B2 1.25 0.0 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 0.0

Design of Substructure for Br. No. 395 64 of 218

Br NO 395-R2 AN1
Maximum 0.0

Unfactored Shear Table

Beari Shear For Unit Width Due to ---
ng DL SIDL FPLL LL-V Seismic
No KN-m KN-m KN-m KN-m KN-m
B1 0.0 0.0 0.0 0.0 0.0
B2 0.0 0.0 0.0 0.0 0.0

ULS -Combination- For RCC Design- SHEAR

Beari DL SIDL FPLL LL-V Seismic ULS Shear-

ng Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN
B1 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0
B2 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0
Maximum 0.0

Checking at Section Abutment CAP -ALONG

Type of Design BEAM

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 16 mm

Spacing in first layer 120 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 312 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 12 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 500 mm
Average Overall depth of the section ( In Tapering Section) hav = 500 mm
Clear cover to Ast Cc = 50 mm

Design of Substructure for Br. No. 395 65 of 218

Br NO 395-R2 AN1
Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 0.0 kN-m
ULS-Total Moment 0.0 kN-m
Ultimate Limit State Shear Vu = 0 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) Abutment CAP -ALONG

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 1809.56 832.00 OK
2 ULS Moment resistance KN-m 0.00 305.07 OK
3 Crack Width mm 0.000 0.20 OK
4 Stress in Steel Mpa 0.00 375.00 OK
5 Stress in Concrete Mpa 0.00 17.5 OK
6 Area of Shear Reinforcement mm2 392.70 221.6 OK
7 Torsional Shear Stress and Capacity Mpa 0.000 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 1.68 0.40 OK
9 Secondary Reinforcement mm2 565 499.2 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 832.00 mm2
As provided = 1809.56 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 416.0 mm
CG of reinforcements, dc 68.0 mm
Number of reinforcing bars, Nb 9.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 1809.56 + 0 1809.6 mm2
Reinf. steel area provided, Ast (flexure) 1809.6 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 387.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 305 kN-m

Design of Substructure for Br. No. 395 66 of 218

Br NO 395-R2 AN1
Serviceability Limit State Check STATUS OK
Crack Width Check
Overall Depth of Section h= 500 mm
Depth of Neutral axis NA, x= 96.22 mm
Distance from to the surface of the nearest longitudinal bar acr = 82.69 mm
Calculated strain in the tension reinforcement es = 0.000000
Strain at cracking LVL- Without stiffening Eff e1 = 0.0000 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000000
Strain at cracking LVL- With stiffening Eff em = 0.0000 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.777E+09 mm4
Crack Width W cr = 0.0000 < 0.2 mm OK Tab-10
Stress in Steel fs = 0.00 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = 0.00 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 0 KN-m

Stress in Steel fs = 0.00 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 0.00 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 1.047
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.535 MPa
vc' = xs vc (2d/av) = 0.561 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 221.6 mm2
Asv prov 392.7 mm2
v = Vu / (bd) 0.000 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 0.0 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 500.0 mm
Smaller Core Dim of Section x1min = 390.0 mm
Longer Outer Dim of Section hmax = 1000.0 mm
Longer Core Dim of Section y1max = 890.0 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.000 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 201.1 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 120.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2

Design of Substructure for Br. No. 395 67 of 218

Br NO 395-R2 AN1
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 1.68 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 416.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 499.2 mm2
Area of reinforcement Provided = 565.2 + 0 565 mm2

Design of Substructure for Br. No. 395 68 of 218

Br NO 395-R2 PN2
Project RJT-KNLS Doubling Project
Client WR-CPM-II-ADI Revision R0
Job Pier For Bridge NO 395 Pier NO PG1 Gr No 1
Prepared By JP Checked By VG App JG
Document No - Date -

Clause Description Value Unit Ref/Remarks

1.0 INPUT DATA

1.1 LEVELS
Proposed Formation Level 30.653 m
Bottom of Super Str- L-Side 30.203 m
Bottom of Super Str- R-Side 30.203 m
Top of Pier Cap L- Side 30.163 m
Top of Pier Cap R- Side 30.163 m
Bottom of Pier Cap 29.163 m
Deepest Scour Level 18.947 m
Bed Level 19.447 m
Highest Flood LVL(HFL)/ Full Supply LVL(FSL) 26.947 m
Low Water Level (LWL) 26.947 m
Intermediate Checking Level 23.405 m
17.647 m
Thickness of Foundation/Foundation Cap 1.200 m
Bottom of Foundation 16.447 m

1.2 GENERAL
Type of Structure (1= Gravity type, 2 = RCC) 2
Type of Project (1= GC, 2 = New) 2
Standard of Loading 3 DFC
Nos of Track 1
C/C of Track ( if More than 1 ) 0.00
Dispersion in Long Load Allowed (Not Allowed = 1,
Allowed = 2) 1 (Cl 2.8.3 Br Rule)
Type of Bridge ( 1 = River, 2 = Viaduct ) 1
Ductile Detailing ( 1 = YES, 2 = NO ) 1
Exposure Condition ( 1- Moderate, 2- Severe, 3= Extreme) 1 5.4 CBC
Curtailment of Long Bar ( 1= No 2 = Yes ) 1 B-3.1.1 Seismic

1.3 LOAD
Span L -Span R -Span DRG NO 10281 10281
Dead Load of Super Str 892 kN
892
Live Load (OSL) 2157.8 2157.8 KN App XXVII- Br Rule
Live Load (TSL) (for Bending Moment) 3345.5 KN App XXVII- Br Rule
Longitudinal Load (OSL) 630.0 630.0 KN App XXVII- Br Rule
Longitudinal Load (TSL) (L 1 + L2 Span) 840.0 KN App XXVII- Br Rule
Weight of Track/m run 65.0 65.0 KN/m As per Calculation

1.4 SPAN
GIRDER L -Girder R -Girder
Clear Span 12.20 12.20 m 10281 10281
Effective Span 12.86 12.86 m 10281 10281
Over All Span 13.38 13.38 m 10281 10281

Design of Substructure for Br. No. 395 69 of 218

Br NO 395-R2 PN2

1.5 Bearings Details

L -Girder R -Girder
Nos of Girder per Track 1 1 Nos
1st- Track-Type of Bearing (1 = Fixed, 2 = Sliding, 3=Free) 2 2
Bearing Material ( 1=Conc, 2 = Steel 3 = Elastomeric 4=
1 1
ROCKER ,5= PTFE)
Eccentricity of Bearing from Centre Line of Pier 0.27 0.27 m
Transverse Spacing of Bearing 1.80 1.80 m
Outer Girder distance from C/L of Pier 0.900 0.900 m
Bearing Size ( Along) -mm 512.5 512.5 mm
Bearing Size ( Transverse) -mm 1.8 1.8 mm
Bearing Thickness ( mm ) 40.0 40.0 mm

F PIER CAP
Top Length- Across The Track 9.000 m
Bottom Length- Transverse The Track 6.300 m
Top Width- Along The Track 2.200 m
Bottom Width- Along The Track 1.500 m
Type of Pier Cap ( 1= Uniform 2= Transverse
Sloping , 3= Both Direction Sloping) 3 m
Level Difference between Pier Cap Top 0 0
Thickness at Edge 0.500 0.500 m
Thickness at Pier - m 1.000 1.000 m
PEDESTAL DETAILS Along Transverse thickness
Left Side Pedestal = 0.000 0.000 0 m
Right Side Pedestal = 0.000 0.000 0 m
Extra Extension for OHE- Trolley Refugee 0 m

1.5 Pier Properties

Plan Shape (1 = Circular, 2= Rectangular) 2
No. of Pier In Plan 1
C/C of Pier for More than one Pier = 0 m
Top Width 1.500 m
Thickness of Bearing 0.040 0.040 m
Depth of Pier Stem 11.516 m
Depth of Pier Stem from BB to INT CHK LVL 5.758 m
Bottom Width of Pier 1.500 m
Batter of Pier Prop 1000
Straight Length at top of Pier Prop 4.800 m
Straight length at Top of Foundation Prop 4.800 m
Shape of Cutwater (1=Triangular, 2 =Circular,3=Rect.) 2
Effective Height Factor 1.200

1.6 FOUNDATION DATA

Type of Foundation (1=Open, 2=Well, 3=Pile) 1

Thickness of Foundation/Cap 1.200 m

OPEN

Foundation Offset (Hora. Projection) 3.5 m

Foundation Sloping Thickness 1.2 0.7 m
Foundation Thickness at end 0 0.5 m
2
Safe Bearing Capacity 470 KN/m
Length (Along traffic) (m) 8.50 m
Width (Transverse traffic) (m) 8.00 m

Design of Substructure for Br. No. 395 70 of 218

Br NO 395-R2 PN2

1.8 Seismic
ZONE IV a = 0.05 b = 1 I = 1.5
Method of Seismic Calculation(1= IRS Coff Method ,2=
IRS response Spectrum) 2

1.8 Hydrological
Velocity of Water 1.850 m/s
Coeff. for Water Pressure (K) 35 Table-4 Sub Str

1.8 WIND
Wind Velocity 0 m/s
Height of Moving Vehicle 4.125 m
Depth of Super Str- Left 0.450 m
Depth of Super Str- RIGHT 0.450 m
Degree of Curve 0.000 deg
Angle of Skew with Perpendicular C/L 0.000 deg
Spacing of Girder 1.800 1.8 m
Coeff. for Leeward Girder 0.500

1.7 Material
Grade of Concrete, Pier Cap- f ck 35 Mpa
Grade of Concrete, Pier 35 Mpa
Grade of Concrete, Foundation 35 Mpa
Grade of Steel, fy 500 Mpa
3
Unit Weight of Sub Str Material 25 KN/m
3
Unit Weight of Soil 20 KN/m
3
Unit Weight Ballast 2.04 t/m
Clear Cover to Reinforcement of Foundation 75 mm
Clear Cover to Reinforcement of Pier 50 mm
Clear Cover to Reinforcement of Pier Ap 50 mm

1.8 MISC
Width of Footpath - Left Side 1 m
Width of Footpath - Right Side 1 m

2 Geometry

Note :- Shapes are automatically Generated Based on INPUT

2.1 PLAN AT PIER CAP LEVEL

9
6.3
0.269

PIER
2.2
1.5

0.269

PLAN AT PIER CAP LEVEL

Design of Substructure for Br. No. 395 71 of 218

Br NO 395-R2 PN2

2.2 PIER PLAN

PIER

1.5
6.3

PIER PLAN

Design of Substructure for Br. No. 395 72 of 218

Br NO 395-R2 PN2
2.3 Transverse Elevation ( m )

9
0.5

1
0.5

PIER
11.516

6.3

6.3
1.2

2.4 Long Elevation (m)

Design of Substructure for Br. No. 395 73 of 218

Br NO 395-R2 PN2
Reinforcement Optimisation

Bar Layer-1 Layer-2

Location Actual/Reqd Capacity/Pro
No Dia Spac Dia Spac
Open Foundation
Bottom Main Reinforcement 32 100 1697 3378 OK
Dis-Horz 16 200 890.4 1004.8 OK
Shear 10 Leg 3 200 0.0 235.6 OK
PIER CAP-ALONG
Top Along Reinforcement 20 200 1.44 707 OK
Dis-Horz 16 200 789.6 1004.8 OK
Shear 12 Leg 6 200 221.6 678.6 OK
PIER CAP-ACROSS
Top Along Reinforcement 25 200 0 1097 OK
Dis-Horz 16 200 783.0 1004.8 OK
Shear 10 Leg 5 200 221.6 392.7 OK

Summary of Output
Sr No Item Unit Actual Permissible Result
PIER-OPEN FOUNDATION
1 Minimum Reinforcement mm2 8042.48 2184.00 OK
2 ULS Moment resistance KN-m 1696.82 3378.19 OK
3 Crack Width mm 0.17 0.25 OK
4 Stress in Steel Mpa 165.81 375.00 OK
5 Stress in Concrete Mpa 8.44 17.50 OK
6 Area of Shear Reinforcement mm2 235.62 0.00 OK
7 Torsional Shear Stress and Capacity Mpa 0.24 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1004.80 890.40 OK
PIER CAP-ALONG
1 Minimum Reinforcement mm2 1884.96 1816.00 OK
2 ULS Moment resistance KN-m 1.44 707.29 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 0.71 375.00 OK
5 Stress in Concrete Mpa 0.02 17.50 OK
6 Area of Shear Reinforcement mm2 678.58 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.03 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 1.58 0.57 OK
9 Secondary Reinforcement mm2 1004.80 789.60 OK
PIER CAP-ACROSS
1 Minimum Reinforcement mm2 2945.24 1805.00 OK
2 ULS Moment resistance KN-m 0.00 1096.97 OK
3 Crack Width mm 0.00 0.20 OK
4 Stress in Steel Mpa 0.00 375.00 OK
5 Stress in Concrete Mpa 0.00 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.93 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 2.46 0.40 OK
9 Secondary Reinforcement mm2 1004.80 783.00 OK

Foundation Pressure and Stability Check Unit Actual Permissible Result

1 Allowed Eccentricity Ratio 4
2 Ratio of Along Eccentricity 7.50 4 OK
3 Ratio of Along Eccentricity 4.02 4 OK
2
4 Max Pressure -Without Distribution KN/m 201.14 470.00 OK
2
5 Min Pressure -Without Distribution KN/m -39.84 0.00 REDIS
2
6 Max Pressure -After Distribution KN/m 214.10 470.00 OK

Design of Substructure for Br. No. 395 74 of 218

Br NO 395-R2 PN2

Effect of Slenderness Cl 15.6.3.1(CBC)

AT INT CHK LVL

Min Dimension in Plane of Bending = h = 1.500 m

min Eccentricity = 0.020 m

Effective Height = Le =1.200 x 5.758 = 6.910 m (Table 18 CBC)

Le / h = 6.910 / 1.500 = 4.606 < 12 Hence Short Col

1 - 0.0035 * Le/ h = 1 - 0.004 x 4.606 = 0.984

Eccentricity due to Slenderness =0.984 / 2.000 = 0.000 m ( For Long Column)

Total Eccentricity = 0.020 + 0.000 = 0.020 m

AT TOP OF FOUNDATION

Min Dimension in Plane of Bending = h = 1.500 m

min Eccentricity = 0.020 m

Effective Height = Le = 1.200 x 11.52 = 13.82 m (As per Table 18 CBC)

Le / h = 13.82 / 1.500 = 9.213 < 12 Hence Short Col

1 - 0.0035 * Le/ h = 1 - 0.0035 x 9.213 = 0.968

Eccentricity due to Slenderness =0.968 / 2.000 = 0.000 m

Total Eccentricity = 0.020 + 0.000 = 0.020 m

3 DEAD LOAD

3.1 DEAD LOAD of SUPER STRUCTURE

Assumption
If Both Span UNEQUAL, Higher Span should be on RIGHT SIDE ( In Dir of Long Load)

Left Span Right Span

Weight of Super STR 892.2 892.2 kN
Reaction of Super Str 446.1 446.1 kN
Nos of Bearing / Girder or Slab 1 1 Nos

Note :- For Slab , Bedding Layer has been considered as bearing

Nos of Track = 1
Eccentricity in Long dir Left Span= 0.269 + 0.020 = 0.289 m From C/L of Pier
Eccentricity in Long dir Right Span = 0.269 + 0.020 = 0.289 m From C/L of Pier

Design of Substructure for Br. No. 395 75 of 218

Br NO 395-R2 PN2
DL1 SUPER STR REACTION
Ver
Transverse Transverse
Bearing Reactio Form Final Reaction Along Ecce Along Moment
n STAAD Ecce Moment
No
kN kN V-KN eL-m eT-m ML-KN-M MT-KN-M
B1 111.5 111.5 0.289 0.900 32.23 100.37
B2 111.5 111.5 0.289 -0.900 32.23 -100.37
B3 112 111.52 -0.289 0.900 -32.23 100.37
B4 112 111.52 -0.289 -0.900 -32.23 -100.37
TOTAL 446.090 D1 0.000 0.000

3.2 OHE MAST

Distance of OHE Mast From Edge of Pier Cap 0.2 m

Width of Base Plate of OHE Mast 0.7 m
Along Eccentricity of OHE Mast 0.1 m
Transverse Eccentricity of OHE Mast 2 m
Weight of OHE Mast 2 t
Number of OHE Mast on Pier 1

Moment - t-m
Vertical ( t )
Load Long ( ML) Transverse ( MT)
D2 2.000 0.200 4.000

3.3 Inspection Platform

Pier Hand Rail

Inspection

0.15

0.900

Self Wt of Slab 0.900 x 0.150 x 25 = 3.375 KN/m

Distance between Vertical Post 1.25 m
Total Length of Inspection Platform 5 m
Nos of Vertical Post 9
Weight of Post ( Assuming ) ISMC-75 0 KN
Weight of Hand Rail ( Assuming ) Dia 48.3 0 KN
Total Weight 0.000 + 0 = 0.000 KN
Total Weight of Hand Rail / m run 0.000 / 5 = 0 KN/m
With Other Misc Item , Rounding Off 0 KN/m
D3 Total 0 KN/m

Note:- As Inspection Platform on Both Side , There will be no Moment

3.4 Trolley Refugee Weight Calculation

Thickness of Slab 0.000 m

Length of Slab 0.000 m
Width of Slab 0.000 m
Width of Beam 0.300 m

Design of Substructure for Br. No. 395 76 of 218

Br NO 395-R2 PN2
Depth of Beam 0.000 m
Length of Beam 0.000 m
Width of C/S of Column 0.300 m
Length of C/S of Column 0.300 m
Height of Column 0.000 m

Weight of Slab = 0.00 x 0.00 x 0.00 x 25 = 0 KN

Weight of Beam = 0.30 x 0.00 x 0.00 x 25 = 0 KN
Weight of Column = 2 x 0.30 x 0.30 x 0.00 x 25 = 0 KN
Weight of Had Rail assuming 3 Layer of 5.1 kg/m 0 KN
Total Weight of Trolley refugee D4 0 KN

3.5 Sub Structure Dead Load

3.5.1 Dead Wt of Pier Cap

2.200 9.000

0.50 2 0.500 0

0.50 1 0.5
1.500 6.300

ALONG TRANSVERSE

L-Dir T-Dir Height

Rectangular Portion Right 2.200 9.000 0.500 m
Bottom of Trapezoidal Portion 1.500 6.300 0.50 m

Eccentricity of Pier Cap in the Longitudinal Direction 0m

Eccentricity of Pier Cap in the Transverse Direction 0m
3
Density 25 KN/m
Width Height
Pier cap Step 1.100 0.000 m
Pier Cap Bottom Level 29.163 m

Weight of Rectangular Portion 247.5 kN

Weight of Trapezoidal Portion =ℎ/6. (𝑎𝑏+AB+(A+a)(B+b)).ϒconc= 242.9 kN
Weight of Pier Cap Step 0 kN
Total Weight of Pier Cap 490 kN

Centroid (from Pier C/L)

Pier Cap Part Weight (kN)
Long. Trans. Height
Rectangular Portion 247.500 0.000 0.000 0.750
Trapezoidal Portion 242.938 0.000 0.000 0.280
Step 0.000 -0.550 0.000 1.000
Total: 490.438 0.000 0.000 0.517

RL of CG of Pier CAP = 29.163 + 0.517 = 29.680

2
X- section Area at top of cap = 2.200 x 9.000 = 19.8 m

2
X- section Area at Bottom of cap = 1.500 x 6.300 = 9.45 m

2
Avg Area for Trap Portion = ( 19.80 + 9.450 ) / 2 = 14.63 m

Design of Substructure for Br. No. 395 77 of 218

Br NO 395-R2 PN2
3
Vol of Rectangular Portion = 19.80 x 0.500 = 9.9 m

3
Vol of Trap Portion = 14.63 x 0.500 = 7.313 m

H Additional Vol of raised cap = 1.100 9.00 0.000 = 0.000 m3

Total Volume = 9.9 + 7.31 + = 17.213 m3

Total Weight = = 490.44 KN

H Along Moment = 490.438 x 0.00 = 0.000 KN-m

Transverse Moment = 490.438 x 0.00 = 0.000 KN-m

Weight of Pedestal

Left Side

Nos of Pedestal = 0

Weight of all Pedestals = 0 x 0x 0x 0x 25.0 = 0 KN

Right Side

Nos of Pedestal = 0

Weight of all Pedestals = 0 x 0x 0x 0x 25.0 = 0 KN

Total Wt of Pedestal = 0.000 + 0 = 0.000 KN

Wt of Pier Cap (D5 )

Vertical Distribution factor = 1.000

Moment - KN-m
Vertical ( Kn )
Load Long ( ML) Transverse ( MT)
D5 490.438 0.000 0.000

3.5.2 Dead Wt of Pier Stem

Shape
Trans Height Wt Up
Sr No Level Thick Str Len
Area Ixx Iyy Zxx Zyy up to To
(1=Cir,2=Cap,3=R
ec,4=Hallow) m m m2 m4 m4 m3 m3 m KN
1 Bottom of BB 2 1.50 4.80 8.38 1.60 27.13 2.13 8.61 0.00 0.0
2 INT CHK LVL 2 1.50 4.80 8.38 1.60 27.13 2.13 8.61 5.76 1205.9
3 TOP OF FND 2 1.50 4.80 8.38 1.60 27.13 2.13 8.61 11.52 2411.9
4 HFL 2 1.50 4.80 8.38 1.60 27.13 2.13 8.61 2.22 464
5 LWL 2 1.50 4.80 8.38 1.60 27.13 2.13 8.61 2.22 464

At Intermediate Checking Level

2
Top Area at Bottom of Pier Cap A1 = 8.378 m
2
Area at Intermediate Checking Level A2 = 8.378 m
Height from Top of Pier to Intermediate Checking Level
h = 5.758 m

Weight up to Int LVL = A1 + A2 + A1 A2 h/3 xg

= 8.378 8.4 + 70.2 + 1.9 + 25 + 1206 KN

Design of Substructure for Br. No. 395 78 of 218

Br NO 395-R2 PN2
Wt of Pier Stem up to INT CHK LVL (D4 )
Moment - t-m
Vertical ( KN)
Load Long ( ML) Transverse ( MT)
D6 1206 0.000 0.000

3.5.3 Dead Wt of Pier Stem ( Up to Top of FND)

At Top of Foundation
Total
Top Area at Bottom of Pier Cap A1 = 8.378 m2
Area at Top of Foundation A2 = 8.378 m2
Height from Bottom of Pier Cap to Top of Foundation h= 11.52 m
Volume = A1 + A2 + A1 A2 h/3 = 96.48 m3
3
Total Volume = 96.48 = 96.48 m
2
Weight of Fill = 0.785 x #REF! x 0.000 x 1.800 = #REF! t
Total Weight up to Top of Foundation = 96.48 x 25.0 = 2411.9 KN

Wt of Pier Stem up to TOF (D7 )

Moment -KN-m
Vertical ( Kn)
Load Long ( ML) Transverse ( MT)
D7 2411.882 0.000 0.000

Total Dead Load up to INT CHK LVL (DL1)

Moment - KN-m
Vertical ( KN )
Load Long ( ML) Transverse ( MT)
DL1 = Sum(D1:D5)+D6 2144.469 0.000 0.000

Total Dead Load up toTOF (DL2)

Moment - KN-m
Vertical ( KN )
Load Long ( ML) Transverse ( MT)
DL2-a = Sum(D1:D5)+D7 3350.410 0.000 0.000
DL2= Sum(D1:D5)+D7* Nos of Pier 3350.410 0 0.000

3.2.3 Weight of Foundation

Plan of Pier at Bottom of Foundation

Y
8.500

X X

Y
8.000

Rec portion
m2
Prop Area = 8.5 X 8.000 = 68.00 m2

Rec Portion

Design of Substructure for Br. No. 395 79 of 218

Br NO 395-R2 PN2
3
8.00x 8.500
Ixx = = 409.417 m4
12

Zxx = 409.417 / 4.250 = 96.333 m3

Rec portion
3
8.5 8.000
Iyy = = 362.667 m4
12

3
Zyy = 362.667 / 4.000 = 90.67 m

5.2.3 At Bottom of Foundation

Top Area at Top of Foundation A1 = 8.378 m2

Area at Bottom of Foundation A2 = 68.000 m2

Depth of Trapezoidal portion h1 = 0.700 m

Depth of Rectangular portion h2 = 0.500 m

Volume of Trapezoidal portion = A1 + A2 + A1 A2 h/3

V1 = 23.391 m3
Volume of Rectangular portion A2 x h2

V2 = 34.000 m3
Total volume, V1 + V2 = 57.39 m3

Weight of Foundation = 57.39 x 25.0 = 1434.76 KN

Weight of Soil of Over Foundation = 68.00 - 8.378 x 1.3 x 20.00

= 1550.185 KN
Final Weight of Foundation = (D8 ) 1434.8 + 1550.2 = 2984.9 KN

Total Dead Load up toBOF (DL3)

Moment - kN-m
Vertical ( t )
Load Long ( ML) Transverse ( MT)
DL3= DL2+D8 6335.4 0.000 0.000

4 Super Imposed DEAD LOAD (SIDL)

Left Span Right Span

Weight of Track /m run 65.0 65.0 kN/m
Overall Span of Girder 13.375 13.375 m
Total Weight of Track 869.4 869.4 kN
Reaction of Super Str 434.7 434.7 kN
Nos of Bearing / Girder 1 1 Nos

Nos of Track = 1
Eccentricity in Long direction Left Span = 0.289 m From C/L of Pier
Eccentricity in Long direction Right Span= 0.289 m From C/L of Pier

SIDL Track and Other Super Imposed Load

Design of Substructure for Br. No. 395 80 of 218

Br NO 395-R2 PN2

Ver Transverse Transverse

Bearing Final Reaction Along Ecce Along Moment
Reactio Form Ecce Moment
No
n STAAD
kN kN V-KN eL-m eT-m ML-KN-M MT-KN-M
B1 109 108.67 0.289 0.900 31.406 97.805
B2 109 108.67 0.289 -0.900 31.406 -97.805
0.000
B3 109 108.67 -0.289 0.900 -31.406 97.805
B4 109 108.67 -0.289 -0.900 -31.406 -97.805
TOTAL 434.688 0.000 0.000

5 Footpath Live Load

Left Side Span ( Side 1 )

Effective Span = 12.86 m

Foot path Width W= 1.000 m

Side-1
2
Load Intensity P = 490 kg/m

Left Side Span ( Side 2 )

Effective Span = 12.86 m

Foot path Width W= 1.000 m

Side-2
2
Load Intensity P = 490 kg/m
=
Right Side Span ( Side 1 )

Effective Span = 12.86 m

Foot path Width W= 1.000 m

Side-1
2
Load Intensity P = 490 kg/m

Right Side Span ( Side 2 )

Effective Span = 12.86 m

Foot path Width W= 1.000 m

Side-2
2
Load Intensity P = 490 kg/m

Left Span Right Span

Load - Load -
Half Width Half Width
P ( Side Reaction P ( Side Reaction
Side Span Side-1 Side Span Side-1
1) 1)

m m KN / m2 KN m m KN/ m2 KN
Side-1 6.432 1.000 4.900 31.51 Side-1 6.43 1.00 4.90 31.51
Side-2 6.432 1.000 4.900 31.51 Side-2 6.43 1.00 4.90 31.51
Total 63.03 Total 63.03
Note
It is assumed that Total Reaction of Foot Path Live Load will be transferred to adjoining Bering.
Left Span Right Span

Design of Substructure for Br. No. 395 81 of 218

Br NO 395-R2 PN2
Reaction -Side 1 31.5 31.5 kN
Reaction -Side 2 31.5 31.5
Nos of Bearing / Girder 1 1 Nos

Nos of Track = 1
Eccentricity in Long direction Right Span = 0.289 m From C/L of Pier
Eccentricity in Long direction Left Span= 0.289 m From C/L of Pier

FPLL FOOTPATH LIVE LOAD

Ver Form Transverse Transverse
Bearing Reactio STAAD Final Reaction Along Ecce Along Moment
Ecce Moment
No
kN kN V-KN eL-m eT-m ML-KN-M MT-KN-M
B1 32 31.51 0.289 0.900 9.108 28.363
B2 32 31.51 0.289 -0.900 9.108 -28.363
0 0.000
B3 32 31.51 -0.289 0.900 -9.108 28.363
B4 32 31.51 -0.289 -0.900 -9.108 -28.363
TOTAL 126.057 0.000 0.000

6 Live Load

As per Clause 5.3 of IRS Substructure code, The minimum live load reaction
corresponding to the maximum longitudinal force shall be considered

6.1 Single Span Loaded

Assumption For Max Reaction on A, First Load Placed on End of A

So that Min Reaction can achieve at B

a Double Headed Diesel Locomotive

0.256 0.256
A B
12.86

Loading Standard = DFC

Combination I Appendix XXVI

Loco Double Head Diesel Loco (DHDL)

Wagon GONDOLA (GW )

Axle Load for Loco 245.25 kN

Tractive Effort / Loco 618.03 kN
Tractive Effort / Axle 103.005 kN
Breaking Foci / Loco Axle 25 %
Breaking force on Tran 13.4 %

Design of Substructure for Br. No. 395 82 of 218

Br NO 395-R2 PN2
LOAD & POSITION CHART
Distance bet - Cum Distance Axle Load - Tractive Load Breaking
Sr No Type m -m KN -KN Load-KN
1 DHDL1 0 0 245.25 103.0 61.31
2 DHDL2 1.85 1.85 245.25 103.0 61.31
3 DHDL3 1.85 3.7 245.25 103.0 61.31
4 DHDL4 9.548 13.248 245.25 103.0 61.31
5 DHDL5 1.85 15.098 245.25 103.0 61.31
6 DHDL6 1.85 16.948 245.25 103.0 61.31
7 DHDL7 5.467 22.415 245.25 103.0 61.31
8 DHDL8 1.85 24.265 245.25 103.0 61.31
9 DHDL9 1.85 26.115 245.25 103.0 61.31
10 DHDL10 9.548 35.663 245.25 103.0 61.31
11 DHDL11 1.85 37.513 245.25 103.0 61.31
12 DHDL12 1.85 39.363 245.25 103.0 61.31
13 GW1 3.828 43.191 318.825 0.0 42.72
14 GW2 2 45.191 318.825 0.0 42.72
15 GW3 4.524 49.715 318.825 0.0 42.72
16 GW4 2 51.715 318.825 0.0 42.72
17 GW5 2.189 53.904 318.825 0.0 42.72
18 GW6 2 55.904 318.825 0.0 42.72
19 GW7 4.524 60.428 318.825 0.0 42.72
20 GW8 2 62.428 318.825 0.0 42.72
21 GW9 2.189 64.617 318.825 0.0 42.72
22 GW10 2 66.617 318.825 0.0 42.72
23 GW11 4.524 71.141 318.825 0.0 42.72
24 GW12 2 73.141 318.825 0.0 42.72
25 GW13 2.189 75.33 318.825 0.0 42.72
26 GW14 2 77.33 318.825 0.0 42.72
27 GW15 4.524 81.854 318.825 0.0 42.72
28 GW16 2 83.854 318.825 0.0 42.72
29 GW17 2.189 86.043 318.825 0.0 42.72
30 GW18 2 88.043 318.825 0.0 42.72

Over All Span =13.38 m Effective Span = 12.86 m Over Hang 0.256 m

Load on Span

Dis of Load
Sr Type from A Ver Load- KN Tractive- KN Breaking- KN Dis from-A Moment abt A
1 DHDL1 0 245.3 103.0 61.3 -0.3 -62.8
2 DHDL2 1.85 245.3 103.0 61.3 1.6 390.9
3 DHDL3 3.7 245.3 103.0 61.3 3.4 844.6
4 DHDL4 13.248 245.3 103.0 61.3 13.0 3186.3
TOTAL 981.0 412.02 245.25 4359

Reaction At B = 4359 / 12.86 = 338.9 kN

Total Vertical Load = 981.00 kN

Maximum Vertical Reaction = 642.12 kN
Minimum Vertical Reaction = 338.88 kN
Longitudinal Force due to Tractive Effort = 412.02 kN
Longitudinal force due to Braking = 245.25 kN

b Double Headed Electric Locomotive

Design of Substructure for Br. No. 395 83 of 218

Br NO 395-R2 PN2

0.256 0.256
A B
12.86

Combination II Appendix XXVI

Loco Double Head Electric Loco (DHEL)

Wagon GONDOLA (GW )

Axle Load for Loco 220.725 kN

Axle Load for Wagon 318.825 kN
Tractive Effort / Loco 510.2 kN
Tractive Effort / Axle 85.03 kN
Breaking Foci / Loco Axle 25 %
Breaking force on Tran 13.4 %

LOAD & POSITION CHART

Sr No Type Distance bet - Cum Distance Axle Load - Tractive Load Breaking
1 DHEL1 0 0 220.725 85.0 55.18
2 DHEL2 1.85 1.85 220.725 85.0 55.18
3 DHEL3 1.85 3.7 220.725 85.0 55.18
4 DHEL4 8.3 12 220.725 85.0 55.18
5 DHEL5 1.85 13.85 220.725 85.0 55.18
6 DHEL6 1.85 15.7 220.725 85.0 55.18
7 DHEL7 4.862 20.562 220.725 85.0 55.18
8 DHEL8 1.85 22.412 220.725 85.0 55.18
9 DHEL9 1.85 24.262 220.725 85.0 55.18
10 DHEL10 8.3 32.562 220.725 85.0 55.18
11 DHEL11 1.85 34.412 220.725 85.0 55.18
12 DHEL12 1.85 36.262 220.725 85.0 55.18
13 GW1 3.526 39.788 318.825 0.0 42.72
14 GW2 2 41.788 318.825 0.0 42.72
15 GW3 4.524 46.312 318.825 0.0 42.72
16 GW4 2 48.312 318.825 0.0 42.72
17 GW5 2.189 50.501 318.825 0.0 42.72
18 GW6 2 52.501 318.825 0.0 42.72
19 GW7 4.524 57.025 318.825 0.0 42.72
20 GW8 2 59.025 318.825 0.0 42.72
21 GW9 2.189 61.214 318.825 0.0 42.72
22 GW10 2 63.214 318.825 0.0 42.72
23 GW11 4.524 67.738 318.825 0.0 42.72
24 GW12 2 69.738 318.825 0.0 42.72
25 GW13 2.189 71.927 318.825 0.0 42.72
26 GW14 2 73.927 318.825 0.0 42.72
27 GW15 4.524 78.451 318.825 0.0 42.72
28 GW16 2 80.451 318.825 0.0 42.72
29 GW17 2.189 82.64 318.825 0.0 42.72
30 GW18 2 84.64 318.825 0.0 42.72

Over All Span =13.38 m Effective Span = 12.86 m Over Hang 0.256 m

Design of Substructure for Br. No. 395 84 of 218

Br NO 395-R2 PN2

Load on Span

Sr Type Dis of Load Ver Load- KN Tractive- KN Breaking- KN Dis from-A Moment abt A
1 DHEL1 0 220.7 85.0 55.2 -0.3 -56.5
2 DHEL2 1.85 220.7 85.0 55.2 1.6 351.8
3 DHEL3 3.7 220.7 85.0 55.2 3.4 760.2
4 DHEL4 12 220.7 85.0 55.2 11.7 2592.2
TOTAL 882.9 340.1 220.725 3648

Reaction At B = 3648 / 12.86 = 283.6 kN

Total Vertical Load = 882.90 kN

Maximum Vertical Reaction = 599.32 kN
Minimum Vertical Reaction = 283.58 kN
Longitudinal Force due to Tractive Effort = 340.13 kN
Longitudinal force due to Braking = 220.73 kN

c Electric Locomotive

0.256 0.256
A B
12.86

Combination III Appendix XXVI

Loco Electric Loco (EL)

Wagon GONDOLA (GW )

Axle Load for Loco 245.25 kN

Axle Load for Wagon 318.825 kN
Tractive Effort / Loco 824.04 kN
Tractive Effort / Axle 103.005 kN
Breaking Foci / Loco Axle 25 %
Breaking force on Tran 13.4 %

LOAD & POSITION CHART

Sr No Type Distance bet - Cum Distance Axle Load - Tractive Load Breaking
1 EL1 0 0 245.25 103.0 61.31
2 EL2 2.8 2.8 245.25 103.0 61.31
3 EL3 5.65 8.45 245.25 103.0 61.31
4 EL4 2.8 11.25 245.25 103.0 61.31
5 EL5 4.3 15.55 245.25 103.0 61.31
6 EL6 2.8 18.35 245.25 103.0 61.31
7 EL7 5.65 24 245.25 103.0 61.31
8 EL8 2.8 26.8 245.25 103.0 61.31
13 GW1 3.425 30.225 318.825 0.0 42.72
14 GW2 2 32.225 318.825 0.0 42.72
15 GW3 4.524 36.749 318.825 0.0 42.72
16 GW4 2 38.749 318.825 0.0 42.72
17 GW5 2.189 40.938 318.825 0.0 42.72
18 GW6 2 42.938 318.825 0.0 42.72

Design of Substructure for Br. No. 395 85 of 218

Br NO 395-R2 PN2
19 GW7 4.524 47.462 318.825 0.0 42.72
20 GW8 2 49.462 318.825 0.0 42.72
21 GW9 2.189 51.651 318.825 0.0 42.72
22 GW10 2 53.651 318.825 0.0 42.72
23 GW11 4.524 58.175 318.825 0.0 42.72
24 GW12 2 60.175 318.825 0.0 42.72
25 GW13 2.189 62.364 318.825 0.0 42.72
26 GW14 20 82.364 318.825 0.0 42.72
27 GW15 4.524 86.888 318.825 0.0 42.72
28 GW16 2 88.888 318.825 0.0 42.72
29 GW17 2.189 91.077 318.825 0.0 42.72
30 GW18 2 93.077 318.825 0.0 42.72

Over All Span =13.38 m Effective Span = 12.86 m Over Hang 0.256 m

Load on Span

Sr Type Dis of Load Ver Load- KN Tractive- KN Breaking- KN Dis from-A Moment abt A
1 EL1 0 245.3 103.0 61.3 -0.3 -62.8
2 EL2 2.8 245.3 103.0 61.3 2.5 623.9
3 EL3 8.45 245.3 103.0 61.3 8.2 2009.6
4 EL4 11.25 245.3 103.0 61.3 11.0 2696.3
TOTAL 981.0 412.02 245.25 5267

Reaction At B = 5267 / 12.86 = 409.5 kN

Total Vertical Load = 981.00 kN

Maximum Vertical Reaction = 571.53 kN
Minimum Vertical Reaction = 409.47 kN
Longitudinal Force due to Tractive Effort = 412.02 kN
Longitudinal force due to Braking = 245.25 kN

d Double Head 25 T LOCO

0.256 0.256
A B
12.86

Combination IV Appendix XXVI

Loco Double Head Electric Loco (DH25L)

Wagon GONDOLA (GW )

Axle Load for Loco 245.25 kN

Axle Load for Wagon 318.825 kN
Tractive Effort / Loco 490.5 kN
Tractive Effort / Axle 81.75 kN
Breaking Foci / Loco Axle 25 %

Design of Substructure for Br. No. 395 86 of 218

Br NO 395-R2 PN2
Breaking force on Tran 13.4 %

LOAD & POSITION CHART

Sr No Type Distance bet - Cum Distance Axle Load - Tractive Load Breaking
1 DH25L1 0 0 245.25 81.8 61.31
2 DH25L2 2.05 2.05 245.25 81.8 61.31
3 DH25L3 1.95 4 245.25 81.8 61.31
4 DH25L4 5.56 9.56 245.25 81.8 61.31
5 DH25L5 1.95 11.51 245.25 81.8 61.31
6 DH25L6 2.05 13.56 245.25 81.8 61.31
7 DH25L7 5.94 19.5 245.25 81.8 61.31
8 DH25L8 2.05 21.55 245.25 81.8 61.31
9 DH25L9 1.95 23.5 245.25 81.8 61.31
10 DH25L10 5.56 29.06 245.25 81.8 61.31
11 DH25L11 1.95 31.01 245.25 81.8 61.31
12 DH25L12 2.05 33.06 245.25 81.8 61.31
13 GW1 4.065 37.125 318.825 0.0 42.72
14 GW2 2 39.125 318.825 0.0 42.72
15 GW3 4.524 43.649 318.825 0.0 42.72
16 GW4 2 45.649 318.825 0.0 42.72
17 GW5 2.189 47.838 318.825 0.0 42.72
18 GW6 20 67.838 318.825 0.0 42.72
19 GW7 4.524 72.362 318.825 0.0 42.72
20 GW8 2 74.362 318.825 0.0 42.72
21 GW9 2.189 76.551 318.825 0.0 42.72
22 GW10 20 96.551 318.825 0.0 42.72
23 GW11 4.524 101.075 318.825 0.0 42.72
24 GW12 20 121.075 318.825 0.0 42.72
25 GW13 2.189 123.264 318.825 0.0 42.72
26 GW14 20 143.264 318.825 0.0 42.72
27 GW15 4.524 147.788 318.825 0.0 42.72
28 GW16 2 149.788 318.825 0.0 42.72
29 GW17 2.189 151.977 318.825 0.0 42.72
30 GW18 2 153.977 318.825 0.0 42.72

Over All Span =13.38 m Effective Span = 12.86 m Over Hang 0.256 m

Load on Span

Sr Type Dis of Load Ver Load- KN Tractive- KN Breaking- KN Dis from-A Moment abt A
1 DH25L1 0 245.3 81.8 61.3 -0.3 -62.8
2 DH25L2 2.05 245.3 81.8 61.3 1.8 440.0
3 DH25L3 4 245.3 81.8 61.3 3.7 918.2
4 DH25L4 9.56 245.3 81.8 61.3 9.3 2281.8
5 DH25L5 11.51 245.3 81.8 61.3 11.3 2760.0
TOTAL 1226.3 408.75 306.5625 6337

Reaction At B = 6337 / 12.86 = 492.7 kN

Total Vertical Load = 1226.25 kN

Maximum Vertical Reaction = 733.58 kN
Minimum Vertical Reaction = 492.67 kN
Longitudinal Force due to Tractive Effort = 408.75 kN
Longitudinal force due to Braking = 306.56 kN

Design of Substructure for Br. No. 395 87 of 218

Br NO 395-R2 PN2
e Double Head 22.5 T LOCO

0.256 0.256
A B
12.86

Combination V Appendix XXVI

Loco Double Head Electric Loco (DH22.5L)

Wagon GONDOLA (GW )

Axle Load for Loco 220.725 kN

Axle Load for Wagon 318.825 kN
Tractive Effort / Loco 490.5 kN
Tractive Effort / Axle 81.75 kN
Breaking Foci / Loco Axle 25 %
Breaking force on Tran 13.4 %

LOAD & POSITION CHART

Sr No Type Distance bet - Cum Distance Axle Load - Tractive Load Breaking
1 DH22.5L1 0 0 220.725 81.8 55.18
2 DH22.5L2 1.65 1.65 220.725 81.8 55.18
3 DH22.5L3 1.65 3.3 220.725 81.8 55.18
4 DH22.5L4 6.4 9.7 220.725 81.8 55.18
5 DH22.5L5 1.65 11.35 220.725 81.8 55.18
6 DH22.5L6 1.65 13 220.725 81.8 55.18
7 DH22.5L7 3 16 220.725 81.8 55.18
8 DH22.5L8 1.65 17.65 220.725 81.8 55.18
9 DH22.5L9 1.65 19.3 220.725 81.8 55.18
10 DH22.5L10 6.4 25.7 220.725 81.8 55.18
11 DH22.5L11 1.65 27.35 220.725 81.8 55.18
12 DH22.5L12 1.65 29 220.725 81.8 55.18
13 GW1 2.595 31.595 318.825 0.0 42.72
14 GW2 2 33.595 318.825 0.0 42.72
15 GW3 4.524 38.119 318.825 0.0 42.72
16 GW4 2 40.119 318.825 0.0 42.72
17 GW5 2.189 42.308 318.825 0.0 42.72
18 GW6 2 44.308 318.825 0.0 42.72
19 GW7 4.524 48.832 318.825 0.0 42.72
20 GW8 2 50.832 318.825 0.0 42.72
21 GW9 2.189 53.021 318.825 0.0 42.72
22 GW10 2 55.021 318.825 0.0 42.72
23 GW11 4.524 59.545 318.825 0.0 42.72
24 GW12 2 61.545 318.825 0.0 42.72
25 GW13 2.189 63.734 318.825 0.0 42.72
26 GW14 2 65.734 318.825 0.0 42.72
27 GW15 4.524 70.258 318.825 0.0 42.72
28 GW16 2 72.258 318.825 0.0 42.72
29 GW17 2.189 74.447 318.825 0.0 42.72
30 GW18 2 76.447 318.825 0.0 42.72

Design of Substructure for Br. No. 395 88 of 218

Br NO 395-R2 PN2
Over All Span =13.38 m Effective Span = 12.86 m Over Hang 0.256 m

Load on Span

Sr Type Dis of Load Ver Load- KN Tractive- KN Breaking- KN Dis from-A Moment abt A
1 DH22.5L1 0 220.7 81.8 55.2 -0.3 -56.5
2 DH22.5L2 1.65 220.7 81.8 55.2 1.4 307.7
3 DH22.5L3 3.3 220.7 81.8 55.2 3.0 671.9
4 DH22.5L4 9.7 220.7 81.8 55.2 9.4 2084.5
5 DH22.5L5 11.35 220.7 81.8 55.2 11.1 2448.7
6 DH22.5L6 13 220.7 81.8 55.2 12.7 2812.9
TOTAL 1324.4 490.5 331.0875 8269

Reaction At B = 8269 / 12.86 = 642.9 kN

Total Vertical Load = 1324.35 kN

Maximum Vertical Reaction = 681.48 kN
Minimum Vertical Reaction = 642.87 kN
Longitudinal Force due to Tractive Effort = 490.50 kN
Longitudinal force due to Braking = 331.09 kN

Summary of Load for Various Combination

As per Clause 5.3 of IRS Substructure code, The minimum live load reaction
corresponding to the maximum longitudinal force shall be considered

Comb I II III IV V VI
Vertical Load 981 883 981 1226 1324 1913
Maximum Vertical reaction 642 599 572 734 681 948
Minimum Vertical reaction 339 284 409 493 643 965
Traction 412 340 412 409 491 0
Braking 245 221 245 307 331 256
Load per Axle 245 221 245 245 221 319

All units in kN
Hence, Arriving at Two Cases
Maximum Longitudinal force with accompanying Vertical Load
Maximum Vertical force with accompanying longitudinal Load

5.1.1 Maximum Longitudinal force with accompanying Vertical Load

CDA = 0.563

Maximum Tractive force 490.5 kN

Maximum Braking Force 331.1 kN
Accompanying Maximum Vertical Reaction 681.5 kN
Accompanying Minimum Vertical Reaction 642.9 kN
Accompanying Maximum Vertical Reaction with CDA 1065.1 kN
Accompanying Minimum Vertical Reaction with CDA 1004.7 kN

5.1.2 Maximum Vertical Load with accompanying Longitudinal Load

CDA = 0.563

Design of Substructure for Br. No. 395 89 of 218

Br NO 395-R2 PN2

Accompanying Tractive force 0.0 kN

Accompanying Braking Force 256.30 kN
Maximum Vertical Reaction 947.8 kN
Accompanying Minimum Vertical Reaction 965.1 kN
Accompanying Maximum Vertical Reaction with CDA 1481.4 kN
Accompanying Minimum Vertical Reaction with CDA 1508.4 kN

5.2 EUDL

5.2.2 For One Span Loaded (O.S.L.)

L-Gir R-Gir
Live Load 2157.8 2157.8
Nos of Track 1.0
Live Load (For all Track) 2157.8 2157.8
C.D.A. = 0.15 + [8 / (6+L)] 0.563 0.563 #REF!
CDA @ Bottom of Pier Cap 0.563 0.563 5.4 ( b ) Sub Str
CDA at Intermediate Checking Level 0.563 0.563 5.4-c Sub Str
CDA at Top of Foundation 0.563 0.563 5.4-c Sub Str
CDA at Bottom of Foundation 0.563 0.563 5.4-c Sub Str
LL with Impact = Live Load x (1 + CDA)
At Top of Pier 1686.2 1686.2 KN
At Intermediate Checking Level 1686.2 1686.2 KN
At Top of Foundation 1686.2 1686.2 KN
At Bottom of Foundation 1686.2 1686.2 KN

For 1 Span Loaded

Max Tractive Force = 630.0 kN

Max Tractive Force = 630.0 kN

5.3 Single Span Loaded Single Track

CG
Distance from Bearing Top to CG of Pier CAP 0.517 + 0.04 = 0.557 m
Left Right
Nos of Girder 1 1 Nos
Outer Girder Inner Girder
Spacing of Right Span Girder 0.900 m 0.900 m
Total 1.8 m

Summary of One Span Loaded Case- OSL

Sr No Description Combination Notation

1a Single Span-Single Track-Eccentricity towards Outside Pmin OSL1
1b Single Span-Single Track-Eccentricity towards Outside Pmax OSL2
1c Single Span-Single Track-Eccentricity towards Outside P-EUDL OSL3
2a Single Span-Single Track-Eccentricity -Inner Side Pmin OSL4
2b Single Span-Single Track-Eccentricity -Inner Side Pmax OSL5
2c Single Span-Single Track-Eccentricity -Inner Side P-EUDL OSL6

Design of Substructure for Br. No. 395 90 of 218

Br NO 395-R2 PN2
5.3.1 Load Distribution Single Span Loaded Single Track

Load Beari Long Load -

S No Calculation V Load- KN
Condition ng On Each KN
1 100 mm Eccentricity towards Outside
Max Long B1 =1004.7x(0.9+0.1)/1.8 558.2 Fact 0.50
a Load(Pmin)- B2 =1004.7x(0.9-0.1)/1.8 446.5 490.5x0.5=
(OSL1) 245.3
Max Vert B1 =1481.4x(0.9+0.1)/1.8 823.0 Fact 0.50
b Load(Pmax)- B2 =1481.4x(0.9-0.1)/1.8 658.4 256.3x0.5=
(OSL2) 128.2
Max Vert B1 =1686.19x(0.9+0.1)/1.8 936.8 Fact 0.50
c Load(P EUDL)- B2 =1686.19x(0.9-0.1)/1.8 749.4 630x0.5=
(OSL3) 315.0
2 100 mm Eccentricity towards Inner Side
Max Long B1 =1004.7x(0.9-0.1)/1.8 446.5
a Load(Pmin)- B2 =1004.7x(0.9+0.1)/1.8 558.2
(OSL4) 245.3
Max Vert B1 =1481.4x(0.9-0.1)/1.8 658.4
b Load(Pmax)- B2 =1481.4x(0.9+0.1)/1.8 823.0
(OSL5) 128.2
Max Vert B1 =1686.19x(0.9-0.1)/1.8 749.4
c Load(P EUDL)- B2 =1686.19x(0.9+0.1)/1.8 936.8
(OSL6) 315.0

Summary of Load on Bearing

LL Reaction DL -Reaction Long Load
Load Case Bearing NO Rq Rg Fh/2
KN KN KN
OSL1 B1 558.2 220.2 245.250
OSL1 B2 446.5 220.2 245.250
OSL1
OSL2 B1 823.0 220.2 128.150
OSL2 B2 658.4 220.2 128.150
OSL2
OSL3 B1 936.8 220.2 315.000
OSL3 B2 749.4 220.2 315.000
OSL3
OSL4 B1 446.5 220.2 245.250
OSL4 B2 558.2 220.2 245.250
OSL4
OSL5 B1 658.4 220.2 128.150
OSL5 B2 823.0 220.2 128.150
OSL5
OSL6 B1 749.4 220.2 315.000
OSL6 B2 936.8 220.2 315.000
OSL6

Design of Substructure for Br. No. 395 91 of 218

Br NO 395-R2 PN2
HORZ FORCE -OSL CONDITION

As per IRC -6 Cl 211.5.1

LHS RHS
Bearing type (1-fix,2-Normal, 3- Free) 2 2
Bearing Material ( 1=Conc, 2 = Steel 3 = Elastomeric 4= ROCKER ,5= PTFE) 1 1
Coff of Friction = m = 0.5 0.5
Creep Strain for Elastomeric Bering
Shrinkage Strain for Elastomeric Bering
Total Strain for Elastomeric Bering ( Ts )
Half Span ( L1) 6688 6688 mm
Horizontal Movement = D = Ts * L1 = mm
Bearing Size ( Along) -mm - BL mm
Bearing Size ( Transverse) -mm -BT mm
Bearing Thickness ( mm ) - T mm
Shear Strain in Bearing = Ss = D / T
Shear Modulus for Elastomeric Bering - Sm Mpa
Shear Stress = Sf = Ss * Sm Mpa
Addition Force = Vr * Itc = Sf * BL * BT KN

Horizontal Bearing Force

At RHS
Bearing Type 2 Normal
Bearing Material 1 Conc

Dead Live
Load Load Long
Bearing No
Load Case

Fixed Bearing Free Bearing Concrete Elastomeric Final

Reactio Reactio Load
n n Bearing Bearing Long
Rg Rq Fh Max of Fh-m(Rg+Rq) Max of Fh/2 Fh/2 + Force
m(Rg+Rq)
or 0.5 *Fh+m(Rg+Rq) or m(Rg) Vr * Itc
KN KN KN KN KN KN KN KN
OSL1 B1 220.2 558.2 245.3 245.25 245
OSL1 B2 220.2 446.5 245.3 245.25 245
OSL2 B1 220.2 823 128.2 245.25 245
OSL2 B2 220.2 658.4 128.2 245.25 245
OSL3 B1 220.2 936.8 315 245.25 245
OSL3 B2 220.2 749.4 315 245.25 245
OSL4 B1 220.2 446.5 245.3 245.25 245
OSL4 B2 220.2 558.2 245.3 245.25 245
OSL5 B1 220.2 658.4 128.2 245.25 245
OSL5 B2 220.2 823 128.2 245.25 245
OSL6 B1 220.2 749.4 315 245.25 245
OSL6 B2 220.2 936.8 315 245.25 245

Design of Substructure for Br. No. 395 92 of 218

Br NO 395-R2 PN2
Longitudinal Load- For One Span Loaded Condition

Long force- Transverse Due to

On Each force- On Curvature
Load Case Bearing No Bearing Each Bearing
Transverse
Along Transverse
Cc= 0.00

REFERENCE Cc*Reaction

OSL1 B1 245.3 0.0 0.0

OSL1 B2 245.3 0.0 0.0
OSL2 B1 245.3 0.0 0.0
OSL2 B2 245.3 0.0 0.0
OSL3 B1 245.3 0.0 0.0
OSL3 B2 245.3 0.0 0.0
OSL4 B1 245.3 0.0 0.0
OSL4 B2 245.3 0.0 0.0
OSL5 B1 245.3 0.0 0.0
OSL5 B2 245.3 0.0 0.0
OSL6 B1 245.3 0.0 0.0
OSL6 B2 245.3 0.0 0.0

At TOP OF FOUNDATION

Top of Bearing = 30.203 TOP OF FOUNDATION 17.647

Height between Bearing and TOP OF FND LVL = 12.556 m

Trans
Trans Trans Along Load Case wise Total
Ver Along Along Vertic verse
verse verse Mome Load & Moments-
Load Load Ecc al Ht Mome

Nos of Track
Load Ecce nt EACH TRACK
nt
Bearin
Case
g NO Hx*H1 Hy*H1
V Hx Hy ex ey H1 V1 Mx1 My1
+V*ex +V*ey

KN Kn KN m m m Mx My kN kN-m kN-m

OSL1 B1 558 245 0 0.289 0.000 12.56 3241 0 1005 6449 0 1

OSL1 B2 447 245 0 0.289 0.000 12.56 3208 0 Hx= 491
OSL2 B1 823 245 0 0.289 0.000 12.56 3317 0 1481 6587 0 1
OSL2 B2 658 245 0 0.289 0.000 12.56 3270 0 Hx= 491
OSL3 B1 937 245 0 0.289 0.000 12.56 3350 0 1686 6646 0 1
OSL3 B2 749 245 0 0.289 0.000 12.56 3296 0 Hx= 491
OSL4 B1 447 245 0 0.289 0.000 12.56 3208 0 1005 6449 0 1
OSL4 B2 558 245 0 0.289 0.000 12.56 3241 0 Hx= 491
OSL5 B1 658 245 0 0.289 0.000 12.56 3270 0 1481 6587 0 1
OSL5 B2 823 245 0 0.289 0.000 12.56 3317 0 Hx= 491
OSL6 B1 749 245 0 0.289 0.000 12.56 3296 0 1686 6646 0 1
OSL6 B2 937 245 0 0.289 0.000 12.56 3350 0 Hx= 491

Design of Substructure for Br. No. 395 93 of 218

Br NO 395-R2 PN2
Summary of Result

LOAD for EACH TRACK

Case No Vert Load - V Along Mo - Transverse Resultant Mo- Horz. Force- Horz. Force-
KN KN-M KN-M KN-M KN KN
OSL1 1005 6449 0 6449 491 0
OSL2 1481 6587 0 6587 491 0
OSL3 1686 6646 0 6646 491 0
OSL4 1005 6449 0 6449 491 0
OSL5 1481 6587 0 6587 491 0
OSL6 1686 6646 0 6646 491 0

Governing LOAD CASE- For ONE SPAN LOADED- TOP OF FOUNDATION

LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
OS1 Max Along Moment- Max-Mx OSL3 1686 6646 0 6646 491 0
OS2 Max Transverse Moment- Max-My OSL1 1005 6449 0 6449 491 0
OS3 Max Resultant Moment- Max-Mr OSL3 1686 6646 0 6646 491 0
OS4 Min Vertical- MIN-V 0 0 0 0 0 0
OS5 Max Vertical- Max-V OSL3 1686 6646 0 6646 491 0
OS6 Max Horz Force- Along - Max-Hx OSL1 1005 6449 0 6449 491 0
OS7 Max Horz Force- Transverse - Max-Hy OSL1 1005 6449 0 6449 491 0

At BOTTOM OF FOUNDATION

Top of Bearing = 30.203 BOTTOM OF FOUNDATION 16.447

Height between Bearing and BOTTOM OF FND LVL = 13.756 m

Trans
Trans Trans Along Load Case wise Total
Ver Along Along Vertic verse
verse verse Mome Load & Moments-
Load Load Ecc al Ht Mome

Nos of Track
Load Ecce nt EACH TRACK
nt
Bearin
Case Hx*H1 Hy*H1
g NO V Hx Hy ex ey H1 V1 Mx1 My1
+V*ex +V*ey

KN Kn KN m m m Mx My kN kN-m kN-m

OSL1 B1 558 245 0 0.289 0.000 13.76 3535 0 1005 7038 0 1

OSL1 B2 447 245 0 0.289 0.000 13.76 3503 0 Hx= 491
OSL2 B1 823 245 0 0.289 0.000 13.76 3612 0 1481 7175 0 1
OSL2 B2 658 245 0 0.289 0.000 13.76 3564 0 Hx= 491
OSL3 B1 937 245 0 0.289 0.000 13.76 3644 0 1686 7235 0 1
OSL3 B2 749 245 0 0.289 0.000 13.76 3590 0 Hx= 491
OSL4 B1 447 245 0 0.289 0.000 13.76 3503 0 1005 7038 0 1
OSL4 B2 558 245 0 0.289 0.000 13.76 3535 0 Hx= 491
OSL5 B1 658 245 0 0.289 0.000 13.76 3564 0 1481 7175 0 1
OSL5 B2 823 245 0 0.289 0.000 13.76 3612 0 Hx= 491
OSL6 B1 749 245 0 0.289 0.000 13.76 3590 0 1686 7235 0 1
OSL6 B2 937 245 0 0.289 0.000 13.76 3644 0 Hx= 491

Design of Substructure for Br. No. 395 94 of 218

Br NO 395-R2 PN2
Summary of Result

LOAD for EACH TRACK

Case No Vert Load - V Along Mo - Transverse Resultant Mo- Horz. Force- Horz. Force-
KN KN-M KN-M KN-M KN KN
OSL1 1005 7038 0 7038 491 0
OSL2 1481 7175 0 7175 491 0
OSL3 1686 7235 0 7235 491 0
OSL4 1005 7038 0 7038 491 0
OSL5 1481 7175 0 7175 491 0
OSL6 1686 7235 0 7235 491 0

Governing LOAD CASE- For ONE SPAN LOADED- BOTTOM OF FOUNDATION

LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
OS1 Max Along Moment- Max-Mx OSL3 1686 7235 0 7235 491 0
OS2 Max Transverse Moment- Max-My OSL1 1005 7038 0 7038 491 0
OS3 Max Resultant Moment- Max-Mr OSL3 1686 7235 0 7235 491 0
OS4 Min Vertical- MIN-V 0 0 0 0 0 0
OS5 Max Vertical- Max-V OSL3 1686 7235 0 7235 491 0
OS6 Max Horz Force- Along - Max-Hx OSL1 1005 7038 0 7038 491 0
OS7 Max Horz Force- Transverse - Max-Hy OSL1 1005 7038 0 7038 491 0

5.4 Double Span Loaded

a Maximum Longitudinal force & Coexisting Vertical reaction case

4 Axle 318.825 kN 4 Axle 318.825 kN

0 Axle 318.825 kN 0 Axle 318.825 kN

S1 S2
A B C D

RA = 637.65 kN
RB = 637.65 kN
RC = 637.65 kN
RD = 637.65 kN
CDA = 0.394

Total Vertical Load on S1 1275.3 kN

Total Vertical Load on S2 1275.3 kN
Reaction on A with CDA 889.059 kN
Reaction on B with CDA 889.059 kN
Reaction on C with CDA 889.059 kN
Reaction on D with CDA 889.059 kN
Longitudinal Force due to Traction on C 200 kN
Longitudinal Force due to Braking on C 200 kN
Longitudinal Force due to Traction on B 200 kN
Longitudinal Force due to Braking on B 200 kN

Design of Substructure for Br. No. 395 95 of 218

Br NO 395-R2 PN2
b Maximum Vertical Load Max longitudinal force

4 Axle 318.825 kN 4 Axle 318.825 kN

S1 S2
A B C D

RA = 637.65 kN
RB = 637.65 kN
RC = 637.65 kN
RD = 637.65 kN
CDA = 0.394

Total Vertical Load on S1 1275 kN

Total Vertical Load on S2 1275.3 kN
Reaction on A with CDA 889.059 kN
Reaction on B with CDA 889.059 kN
Reaction on C with CDA 889.059 kN
Reaction on D with CDA 889.059 kN
Longitudinal Force due to Traction on C 200 kN
Longitudinal Force due to Braking on C 200 kN
Longitudinal Force due to Traction on B 200 kN
Longitudinal Force due to Braking on B 200 kN

c Minimum Vertical Load with coexisting longitudinal force

4 Axle 318.825 kN 4 Axle 318.825 kN

0 Axle 318.825 kN

S1 S2
A B C D

RA = 637.65 kN
RB = 637.65 kN
RC = 637.65 kN
RD = 637.65 kN
CDA = 0.394

Total Vertical Load on S1 1275.3 kN

Total Vertical Load on S2 1275.3 kN
Reaction on A with CDA 889.059 kN
Reaction on B with CDA 889.059 kN
Reaction on C with CDA 889.059 kN
Reaction on D with CDA 889.059 kN
Longitudinal Force due to Traction on C 200 kN
Longitudinal Force due to Braking on C 200 kN
Longitudinal Force due to Traction on B 200 kN
Longitudinal Force due to Braking on B 200 kN

Design of Substructure for Br. No. 395 96 of 218

Br NO 395-R2 PN2
5.4.1 For Two Span Loaded (T.S.L.)

Live Load 3345.46

Nos of Track 1
Live Load 3345.5
C.D.A. = 0.15 + [8 / (6+L)] 0.394
CDA @ Bottom of Pier Cap 0.394 5.4 ( b ) Sub Str
CDA at Intermediate Checking Level 0.394 5.4-c Sub Str
CDA at Top of Foundation 0.394 5.4-c Sub Str
CDA at Bottom of Foundation 0.394 5.4-c Sub Str

LL with Impact = Live Load x (1 + CDA)

Total reaction on Reaction on Left Reaction on Right UDL (KN/m)
Pier (R) (t) Bearing (t) Bearing (KN)
Location
LL(1+CDA)/2 R*L1/(L1+L2) R*L2/(L1+L2) 2R/(L1+L2)
At Top of Pier 2332.25 1166.12 1166.12 174.37
At Intermediate Checking Level 2332.25 1166.12 1166.12 174.37
At Top of Foundation 2332.25 1166.12 1166.12 174.37
At Bottom of Foundation 2332.25 1166.12 1166.12 174.37

Distribution Factor = 1.000

Summary Of TSL- LIVE LOAD
Eccentri Eccentri Net Net
Distributi Moment- Moment- Moment-
Reacti city- city- Moment-
on Reaction Along- Along- Trans- Trans-
LEVEL on Factor
Along- Trans-
ML
eL eT ML MT MT
Side Kn kN m m Kn-m Kn-m Kn-m Kn-m
Left 1166 1 1166 0 0 337 0
0 0
INT(LL21) Right 1166 1 1166 0 0 337 0
Total Vertical 2332.2
Left 1166 1 1166 0 0 337 0
0 0
TOF(LL22) Right 1166 1 1166 0 0 337 0
Total Vertical 2332.2
Left 1166 1 1166 0 0 337 0
0 0
BOF(LL23) Right 1166 1 1166 0 0 337 0
Total Vertical 2332.2

Vehicle Config a b c EUDL

Vertical Load - Span 1 1275.30 1275.30 1275.30 1672.73
Vertical Load - Span 2 1275.30 1275.30 1275.30 1672.73
Reaction A 889.06 889.06 889.06 836.37
All Load in KN

Reaction B 889.06 889.06 889.06 836.37

Reaction C 889.06 889.06 889.06 836.37
Reaction D 889.06 889.06 889.06 836.37
Traction- C 200.00 200.00 200.00 220.00
Braking-C 200.00 200.00 200.00 220.00
Traction-B 200.00 200.00 200.00 220.00
Braking-B 200.00 200.00 200.00 220.00

As per Clause 5.3 of IRS Substructure code, The minimum live load reaction
corresponding to the maximum longitudinal force shall be considered

Design of Substructure for Br. No. 395 97 of 218

Br NO 395-R2 PN2
Outer Girder Inner Girder
Left Span Girder Spacing from C/L of Track 0.9 m 0.900 m
Total 1.8 m

5.4.3 Double Span - Single Track

Load Beari
S No Calculation V Load- KN L.L KN
Condition ng
1 100 mm Eccentricity towards Outside
B1 =889.059x(0.9+0.1)/1.8 493.9 Fact 0.50
Max Long B2 =889.059x(0.9-0.1)/1.8 395.1 200x0.5=
Load(Pmin) 100.0
a (Hmax+Pmin)- B3 =889.059x(0.9+0.1)/1.8 493.9 Fact 0.50
(TSL1) B4 =889.059x(0.9-0.1)/1.8 395.1 200x0.5=
100.0
B1 =889.059x(0.9+0.1)/1.8 493.9 Fact 0.50
B2 =889.059x(0.9-0.1)/1.8 395.1 200x0.5=
Max Vert Load
100.0
b (Pmax)-
(TSL2)
B3 =889.059x(0.9+0.1)/1.8 493.9 Fact 0.50
B4 =889.059x(0.9-0.1)/1.8 395.1 200x0.5=
100.0
B1 =836.36535x(0.9+0.1)/1.8 464.6 Fact 0.50
B2 =836.36535x(0.9-0.1)/1.8 371.7 220x0.5=
Max Vert
110.0
d Load(P EUDL)-
(TSL3)
B3 =836.36535x(0.9+0.1)/1.8 464.6 Fact 0.50
B4 =836.36535x(0.9-0.1)/1.8 371.7 220x0.5=
110.0
2 100 mm Eccentricity towards Inner Side
B1 =889.059x(0.9-0.1)/1.8 395.1 Fact 0.50
Max Long B2 =889.059x(0.9+0.1)/1.8 493.9 200x0.5=
Load(Pmin) 100.0
a (Hmax+Pmin)- B3 =889.059x(0.9-0.1)/1.8 395.1 Fact 0.50
(TSL4) B4 =889.059x(0.9+0.1)/1.8 493.9 200x0.5=
100.0
B1 =889.059x(0.9-0.1)/1.8 395.1 Fact 0.50
B2 =889.059x(0.9+0.1)/1.8 493.9 200x0.5=
Max Vert Load
100.0
b (Pmax)-
(TSL5)
B3 =889.059x(0.9-0.1)/1.8 395.1 Fact 0.50
B4 =889.059x(0.9+0.1)/1.8 493.9 200x0.5=
100.0
B1 =836.36535x(0.9-0.1)/1.8 371.7 Fact 0.50
B2 =836.36535x(0.9+0.1)/1.8 464.6 220x0.5=
Max Vert
110.0
d Load(P EUDL)-
(TSL6)
B3 =836.36535x(0.9-0.1)/1.8 371.7 Fact 0.50
B4 =836.36535x(0.9+0.1)/1.8 464.6 220x0.5=
110.0

LL Reaction DL -Reaction Long Load

Load Case Bearing NO Rq Rg Fh/2
KN KN KN
TSL1 B1 493.9 220.2 100.000
TSL1 B2 395.1 220.2 100.000
TSL1 B3 493.9 220.2 100.000
TSL1 B4 395.1 220.2 100.000
TSL2 B1 493.9 220.2 100.000
TSL2 B2 395.1 220.2 100.000

Design of Substructure for Br. No. 395 98 of 218

Br NO 395-R2 PN2
TSL2 B3 493.9 220.2 100.000
TSL2 B4 395.1 220.2 100.000
TSL3 B1 464.6 220.2 110.000
TSL3 B2 371.7 220.2 110.000
TSL3 B3 464.6 220.2 110.000
TSL3 B4 371.7 220.2 110.000
TSL4 B1 395.1 220.2 100.000
TSL4 B2 493.9 220.2 100.000
TSL4 B3 395.1 220.2 100.000
TSL4 B4 493.9 220.2 100.000
TSL5 B1 395.1 220.2 100.000
TSL5 B2 493.9 220.2 100.000
TSL5 B3 395.1 220.2 100.000
TSL5 B4 493.9 220.2 100.000
TSL6 B1 371.7 220.2 110.000
TSL6 B2 464.6 220.2 110.000
TSL6 B3 371.7 220.2 110.000
TSL6 B4 464.6 220.2 110.000

HORZ FORCE -TSL CONDITION

As per IRC -6 Cl 211.5.1

LHS RHS
Bearing type (1-fix,2-Normal, 3- Free) 2 2
Bearing Material ( 1=Conc, 2 = Steel 3 = Elastomeric 4= ROCKER ,5= PTFE) 1 1
Coff of Friction = m = 0.5 0.5
Creep Strain for Elastomeric Bering
Shrinkage Strain for Elastomeric Bering
Total Strain for Elastomeric Bering ( Ts )
Half Span ( L1) 6688 6688 mm
Horizontal Movement = D = Ts * L1 = mm
Bearing Size ( Along) -mm - BL mm
Bearing Size ( Transverse) -mm -BT mm
Bearing Thickness ( mm ) - T mm
Shear Strain in Bearing = Ss = D / T
Shear Modulus for Elastomeric Bering - Sm Mpa
Shear Stress = Sf = Ss * Sm Mpa
Addition Force = Vr * Itc = Sf * BL * BT KN

Horizontal Bearing Force

At LHS RHS
Bearing Type 2 Normal 2 Normal
Bearing Material 1 Conc 1 Conc

Dead Live
Load Load Long
Bearing No

Concrete Elastomeric
Load Case

Fixed Bearing Free Bearing Final

Reactio Reactio Load
n n
Bearing Bearing Long
Rg Rq Fh/2 Max of Fh-m(Rg+Rq) m(Rg+Rq) Max of Fh/2 Fh/2 + Force
or 0.5 *Fh+m(Rg+Rq) or m(Rg) Vr * Itc
KN KN KN KN KN KN KN KN
TSL1 B1 220.2 493.9 100 110.0971875 110
TSL1 B2 220.2 395.1 100 110.0971875 110
TSL1 B3 220.2 493.9 100 110.0971875 110
TSL1 B4 220.2 395.1 100 110.0971875 110
TSL2 B1 220.2 493.9 100 110.0971875 110
TSL2 B2 220.2 395.1 100 110.0971875 110
TSL2 B3 220.2 493.9 100 110.0971875 110

Design of Substructure for Br. No. 395 99 of 218

Br NO 395-R2 PN2
TSL2 B4 220.2 395.1 100 110.0971875 110
TSL3 B1 220.2 464.6 110 110.0971875 110
TSL3 B2 220.2 371.7 110 110.0971875 110
TSL3 B3 220.2 464.6 110 110.0971875 110
TSL3 B4 220.2 371.7 110 110.0971875 110
TSL4 B1 220.2 395.1 100 110.0971875 110
TSL4 B2 220.2 493.9 100 110.0971875 110
TSL4 B3 220.2 395.1 100 110.0971875 110
TSL4 B4 220.2 493.9 100 110.0971875 110
TSL5 B1 220.2 395.1 100 110.0971875 110
TSL5 B2 220.2 493.9 100 110.0971875 110
TSL5 B3 220.2 395.1 100 110.0971875 110
TSL5 B4 220.2 493.9 100 110.0971875 110
TSL6 B1 220.2 371.7 110 110.0971875 110
TSL6 B2 220.2 464.6 110 110.0971875 110
TSL6 B3 220.2 371.7 110 110.0971875 110
TSL6 B4 220.2 464.6 110 110.0971875 110

Longitudinal Load- For Two Span Loaded Condition

Due to
Long force- Long force-
Curvature
On Each On Each
Load Case Bearing No Bearing Bearing
Transverse
Trans
Along 1 0 Cc= 0.00
verse

REFERENCE Cc*Reaction

TSL1 B1 110.1 0.0 0.0

TSL1 B2 110.1 0.0 0.0
TSL1 B3 110.1 0.0 0.0
TSL1 B4 110.1 0.0 0.0
TSL2 B1 110.1 0.0 0.0
TSL2 B2 110.1 0.0 0.0
TSL2 B3 110.1 0.0 0.0
TSL2 B4 110.1 0.0 0.0
TSL3 B1 110.1 0.0 0.0
TSL3 B2 110.1 0.0 0.0
TSL3 B3 110.1 0.0 0.0
TSL3 B4 110.1 0.0 0.0
TSL4 B1 110.1 0.0 0.0
TSL4 B2 110.1 0.0 0.0
TSL4 B3 110.1 0.0 0.0
TSL4 B4 110.1 0.0 0.0
TSL5 B1 110.1 0.0 0.0
TSL5 B2 110.1 0.0 0.0
TSL5 B3 110.1 0.0 0.0
TSL5 B4 110.1 0.0 0.0
TSL6 B1 110.1 0.0 0.0
TSL6 B2 110.1 0.0 0.0
TSL6 B3 110.1 0.0 0.0
TSL6 B4 110.1 0.0 0.0

Summary 2 Span Loaded Condition

Design of Substructure for Br. No. 395 100 of 218

Br NO 395-R2 PN2

At TOP OF FOUNDATION

Top of Bearing = 30.203 Top OF FOUNDATION 17.647

Height between Bearing and TOP OF FOUNDATION = 12.556 m

Trans
Trans Trans Along Load Case wise Total
Ver Along Along Vertic verse
verse verse Mome Load & Moments-
Load Load Ecc al Ht Mome

Nos of Track
Load Ecce nt EACH TRACK
nt
Bearin
Case
g NO Hx*H1 Hy*H1
V Hx Hy ex ey H1 V1 Mx1 My1
+V*ex +V*ey

KN Kn KN m m m Mx My kN kN-m kN-m

TSL1 B1 494 110 0 0.289 0.000 12.56 1525 0 1778 6043 0 1

TSL1 B2 395 110 0 0.289 0.000 12.56 1497 0 Hx= 440
TSL1 B3 494 110 0 0.289 0.000 12.56 1525 0
TSL1 B4 395 110 0 0.289 0.000 12.56 1497 0
TSL2 B1 494 110 0 0.289 0.000 12.56 1525 0 1778 6043 0 1
TSL2 B2 395 110 0 0.289 0.000 12.56 1497 0 Hx= 440
TSL2 B3 494 110 0 0.289 0.000 12.56 1525 0
TSL2 B4 395 110 0 0.289 0.000 12.56 1497 0
TSL3 B1 465 110 0 0.289 0.000 12.56 1517 0 1673 6013 0 1
TSL3 B2 372 110 0 0.289 0.000 12.56 1490 0 Hx= 440
TSL3 B3 465 110 0 0.289 0.000 12.56 1517 0
TSL3 B4 372 110 0 0.289 0.000 12.56 1490 0
TSL4 B1 395 110 0 0.289 0.000 12.56 1497 0 1778 6043 0 1
TSL4 B2 494 110 0 0.289 0.000 12.56 1525 0 Hx= 440
TSL4 B3 395 110 0 0.289 0.000 12.56 1497 0
TSL4 B4 494 110 0 0.289 0.000 12.56 1525 0
TSL5 B1 395 110 0 0.289 0.000 12.56 1497 0 1778 6043 0 1
TSL5 B2 494 110 0 0.289 0.000 12.56 1525 0 Hx= 440
TSL5 B3 395 110 0 0.289 0.000 12.56 1497 0
TSL5 B4 494 110 0 0.289 0.000 12.56 1525 0
TSL6 B1 372 110 0 0.289 0.000 12.56 1490 0 1673 6013 0 1
TSL6 B2 465 110 0 0.289 0.000 12.56 1517 0 Hx= 440
TSL6 B3 372 110 0 0.289 0.000 12.56 1490 0
TSL6 B4 465 110 0 0.289 0.000 12.56 1517 0

Summary of Result
LOAD for EACH TRACK
Case No Vert Load - V Along Mo - Transverse Resultant Mo- Horz. Force- Horz. Force-
KN KN-M KN-M KN-M KN KN
TSL1 1778 6043 0 6043 440 0
TSL2 1778 6043 0 6043 440 0
TSL3 1673 6013 0 6013 440 0
TSL4 1778 6043 0 6043 440 0
TSL5 1778 6043 0 6043 440 0
TSL6 1673 6013 0 6013 440 0

Design of Substructure for Br. No. 395 101 of 218

Br NO 395-R2 PN2
Governing LOAD CASE- For 2 SPAN LOADED
LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
TS1 Max Along Moment- Max-Mx TSL1 1778 6043 0 6043 440 0
TS2 Max Transverse Moment- Max-My TSL1 1778 6043 0 6043 440 0
TS3 Max Resultant Moment- Max-Mr TSL1 1778 6043 0 6043 440 0
TS4 Min Vertical- MIN-V 0 0 0 0 0 0
TS5 Max Vertical- Max-V TSL1 1778 6043 0 6043 440 0
TS6 Max Horz Force- Along - Max-Hx TSL1 1778 6043 0 6043 440 0
TS7 Max Horz Force- Transverse - Max-Hy TSL1 1778 6043 0 6043 440 0

At BOTTOM OF FOUNDATION

Top of Bearing = 30.203 BOTTOM OF FOUNDATION 16.447

Height between Bearing and TOP OF FOUNDATION = 13.756 m

Trans
Trans Trans Along Load Case wise Total
Ver Along Along Vertic verse
verse verse Mome Load & Moments-
Load Load Ecc al Ht Mome
Load Ecce nt EACH TRACK

Nos of Track
nt
Bearin
Case Hx*H1 Hy*H1
g NO V Hx Hy ex ey H1 V1 Mx1 My1
+V*ex +V*ey

KN Kn KN m m m Mx My kN kN-m kN-m

TSL1 B1 494 110 0 0.289 0.000 13.76 1657 0 1778 6572 0 1

TSL1 B2 395 110 0 0.289 0.000 13.76 1629 0 Hx= 440
TSL1 B3 494 110 0 0.289 0.000 13.76 1657 0
TSL1 B4 395 110 0 0.289 0.000 13.76 1629 0
TSL2 B1 494 110 0 0.289 0.000 13.76 1657 0 1778 6572 0 1
TSL2 B2 395 110 0 0.289 0.000 13.76 1629 0 Hx= 440
TSL2 B3 494 110 0 0.289 0.000 13.76 1657 0
TSL2 B4 395 110 0 0.289 0.000 13.76 1629 0
TSL3 B1 465 110 0 0.289 0.000 13.76 1649 0 1673 6541 0 1
TSL3 B2 372 110 0 0.289 0.000 13.76 1622 0 Hx= 440
TSL3 B3 465 110 0 0.289 0.000 13.76 1649 0
TSL3 B4 372 110 0 0.289 0.000 13.76 1622 0
TSL4 B1 395 110 0 0.289 0.000 13.76 1629 0 1778 6572 0 1
TSL4 B2 494 110 0 0.289 0.000 13.76 1657 0 Hx= 440
TSL4 B3 395 110 0 0.289 0.000 13.76 1629 0
TSL4 B4 494 110 0 0.289 0.000 13.76 1657 0
TSL5 B1 395 110 0 0.289 0.000 13.76 1629 0 1778 6572 0 1
TSL5 B2 494 110 0 0.289 0.000 13.76 1657 0 Hx= 440
TSL5 B3 395 110 0 0.289 0.000 13.76 1629 0
TSL5 B4 494 110 0 0.289 0.000 13.76 1657 0
TSL6 B1 372 110 0 0.289 0.000 13.76 1622 0 1673 6541 0 1
TSL6 B2 465 110 0 0.289 0.000 13.76 1649 0 Hx= 440
TSL6 B3 372 110 0 0.289 0.000 13.76 1622 0
TSL6 B4 465 110 0 0.289 0.000 13.76 1649 0

Summary of Result

Design of Substructure for Br. No. 395 102 of 218

Br NO 395-R2 PN2
LOAD for EACH TRACK
Case No Vert Load - V Along Mo - Transverse Resultant Mo- Horz. Force- Horz. Force-
KN KN-M KN-M KN-M KN KN
TSL1 1778 6572 0 6572 440 0
TSL2 1778 6572 0 6572 440 0
TSL3 1673 6541 0 6541 440 0
TSL4 1778 6572 0 6572 440 0
TSL5 1778 6572 0 6572 440 0
TSL6 1673 6541 0 6541 440 0

Governing LOAD CASE- For 2 SPAN LOADED- Bottom Of FOUNDATION

LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
TS1 Max Along Moment- Max-Mx TSL1 1778 6572 0 6572 440 0
TS2 Max Transverse Moment- Max-My TSL1 1778 6572 0 6572 440 0
TS3 Max Resultant Moment- Max-Mr TSL1 1778 6572 0 6572 440 0
TS4 Min Vertical- MIN-V 0 0 0 0 0 0
TS5 Max Vertical- Max-V TSL1 1778 6572 0 6572 440 0
TS6 Max Horz Force- Along - Max-Hx TSL1 1778 6572 0 6572 440 0
TS7 Max Horz Force- Transverse - Max-Hy TSL1 1778 6572 0 6572 440 0

Governing LIVE LOAD ( Critical of 1 or 2 SPAN Loaded )

TOP OF FOUNDATION

LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
L1 Max Along Moment- Max-Mx OSL3 1686 6646 0 6646 491 0
L2 Max Transverse Moment- Max-My OSL1 1005 6449 0 6449 491 0
L3 Max Resultant Moment- Max-Mr OSL3 1686 6646 0 6646 491 0
L4 Min Vertical- MIN-V 0 0 0 0 0 0
L5 Max Vertical- Max-V TSL1 1778 6646 0 6646 491 0
L6 Max Horz Force- Along - Max-Hx OSL1 1005 6449 0 6449 491 0
L7 Max Horz Force- Transverse - Max-Hy OSL1 1005 6449 0 6449 491 0

BOTTOM OF FOUNDATION

LOAD V Mx My Mr Hx Hy
Sr NO Condition
CASE
KN kN-m kN-m kN-m KN KN
L1 Max Along Moment- Max-Mx OSL3 1686 7235 0 7235 491 0
L2 Max Transverse Moment- Max-My OSL1 1005 7038 0 7038 491 0
L3 Max Resultant Moment- Max-Mr OSL3 1686 7235 0 7235 491 0
L4 Min Vertical- MIN-V 0 0 0 0 0 0
L5 Max Vertical- Max-V TSL1 1778 7235 0 7235 491 0
L6 Max Horz Force- Along - Max-Hx OSL1 1005 7038 0 7038 491 0
L7 Max Horz Force- Transverse - Max-Hy OSL1 1005 7038 0 7038 491 0

Design of Substructure for Br. No. 395 103 of 218

Br NO 395-R2 PN2
6 LWR Forces
Max Long Force in Normal condition ( Max of Breaking /Tractive) = 630.0 KN
Max Long Force in Normal condition ( Max of Breaking /Tractive) = 630.0 KN
B1 0.50 0.000 0.000 0 0 0 0 0 0
B2 0.50 0.000 0.000 0 0 0 0 0 0
B3 0.50 0.0 0.000 0 0 0 0 0 0
B4 0.50 0.0 0.000 0 0 0 0 0 0

7 WATER FORCE

7.1 BUOYANCY FORCE

7.1.2 At Top of Foundation

7.1.2.1 For AHFL
A1 = 8.378 m2 1.5.1.
Area of Pier at AHFL
A2 = 3
1.5.1.
Area at Top of Foundation 8.378 m2
4
Depth between AHFL & Top of Foundation h = 9.300 m

Buoyant Force up to TOF = A1 + A2 + A1 A2 h/3 x gw x 100%

= 8.378 8.38 + √70.2) 3.1x 1.0x 100% = 779.1 KN
(Assuming 100% Buoyancy) As per Cl 5.10.2 Sub St.

7.1.2.2 For LWL

Area of Pier at LWL A1 = 8.378 m2
Area at Top of Foundation A2 = 8.378 m2
Depth between LWL & Top of Foundation h = 9.300 m

Buoyant Force up to TOF = A1 + A2 + A1 A2 h/3 x gw x 100%

= 8.378 8.38 + √70.2) 3.10x 1.00x 100% = 779.1 KN
(Assuming 100% Buoyancy) As per Cl 5.10.2 Sub St.

7.1.3 At Bottom of Foundation

3
Volume of Foundation = 25.00 m

Buoyant Force due to Foundation = 25.00 x gw = 250.0 KN

7.1.3.1 For AHFL

Buoyant Force up to TOF (100%) = 779.1 t 6.2.1
Buoyant Force due to Foundation 250.0 t 6.2.2
h=
Depth between AHFL & Bottom of Foundation 10.50 m

Buoyant Force up to BOF = 779.1 = 250 1029 = x 100%

= 1029 100% = 1029.1 KN
(Assuming 100% Buoyancy)

7.1.3.2 For LWL

Buoyant Force up to TOF 779.1 KN
Buoyant Force due to Foundation 250 = KN
Depth between LWL & Bottom of Foundationh = 0.000 m

Buoyant Force up to BOF = 779.11 0.00 = 779.1 x 100%

= 779.11 100% = 779.1 t

If LWL is below Top of Foundation but above Bottom of Foundation, it is assumed that LWL is
just below Top of Foundation. If LWL is below Bottom of Foundation Effect of LWL is ignored.

Design of Substructure for Br. No. 395 104 of 218

Br NO 395-R2 PN2
(Assuming 100% Buoyancy) As per Cl 5.10.2 Sub St.

7.2 WATER PRESSURE

7.2.2 At Top of Foundation

7.2.2.1 For AHFL
Width at AHFL b1 1.500 m
Width at Top of Foundation b2 1.500 m
Height from AHFL to Top of Foundation h 9.300 m

Area in Elevation between AHFL to Top of FND A = (b1+b2)h/2 = 13.95 m2

2
Water Force (Transverse the Track) KAV2 = 35x 13.95x 1.850 = 16.71 KN
Water Force (Along the Track 20% of Transverse track)
= 20% 16.7 = 3.342 KN
Lever arm (2h/3) = 6.200 m

7.2.2.2 For LWL

Width at LWL b1 1.500 m
Width at Top of Foundation b2 1.500 m
Height from LWL to Top of Foundation h 9.300 m

Area in Elevation between LWL to TOFA = (b1+b2)h/2 = 13.95 m2

2
Water Force (Transverse the Track) KAV2 = 35x 13.95x 1.850 = 16.71 KN
Water Force (Along the Track 20% of Transverse track)
= 20% 16.710 = 3.342 KN
Lever arm (2h/3) = 6.200 m

7.2.3 At Bottom of Foundation

7.2.3.1 For AHFL
Force at Top of Foundation
Transverse the track = 16.71 KN 7.2.1
Along the track = 3.34 KN
Lever Arm @ 6.200 m above TOF
Moment about Bottom of Foundation
Load x [L.A.@ TOF + (TOF-BOF)]
Transverse the track = 16.71 x 6.20 x 1.20 x = 123.657 KN-m
Along the track = 3.34 x 6.20 x 1.20 x = 24.731 KN-m

Additional Water Pressure in Foundation Portion =

Width at Top of Foundation = b1 1.500 m

Width at Bottom of Foundation = b2 8.500 m
TOF to BOF (For AHFL) = h 1.200 m

Area in Elevation between BOF to TOFA = (b1+b2)h/2 = 6.000 m2

2
Water Force (Transverse the Track) KAV2 = 79x 6.00x 1.850 = 16.22 KN
Water Force (Along the Track 20% of Transverse track)
= 20% 16.22 = 3.24 kN
Lever arm (2h/3) = 0.800 m

Moment Load x L.A.

Transverse the track = 16.2 x 0.800 = 13 KN-m
Along the track = 3.2 x 0.800 = 3 KN-m

16.7=+
Total Horizontal Force Transverse the track 16.22 = 32.93 KN
Total Horizontal Force Along the track = 3.3 + 3.24 = 6.59 KN

Total Moment Transverse the track = 123.7 + 12.98 = 136.6 KN-m

Total Moment Along the track = 24.7 + 2.60 = 27.33 KN-m

7.2.3.2 For LWL

Force at Top of Foundation

Design of Substructure for Br. No. 395 105 of 218

Br NO 395-R2 PN2

Transverse the track = 16.71 KN

Along the track = 3.342 KN

Lever Arm @ 6.200 m above TOF 7.2.1

Moment about Bottom of Foundation

Load x [L.A.@ TOF + (TOF-BOF)]
Transverse the track = 16.7 x 6.2 x 1.20 = 123.657 kN-m
Along the track = 3.3 x 6.2 x 1.20 = 24.731 kN-m

Additional Water Pressure in Foundation Portion =

Width at Top of Foundation = b1 1.500 m

Width at Bottom of Foundation = b2 8.500 m
TOF to BOF (For LWL ) = h 1.200 m

Area in Elevation between LWL to TOFA = (b1+b2)h/2 = 6.000 m2

Water Force (Transverse the Track) KAV2=
2
79x 6.00x 1.850 = 16.223 KN
Water Force (Along the Track 20% of Transverse track) = 20% 16.223 = 3.245 KN

Lever arm (2h/3) = 0.800 m

Moment Load x L.A.

Transverse the track = 16.2 x 0.800 = 12.978 KN-m
Along the track = 3.2 x 0.800 = 2.596 KN-m

Total Horizontal Force Transverse the track = 16.7 + 16.2 + = 32.9 + KN

Total Horizontal Force Along the track = 3.34 + 3.245 = 6.587 KN

Total Moment Transverse the track = 123.66 + 12.978 = 136.635 kN-m

Total Moment Along the track = 24.73 + 2.596 = 27.327 kN-m

Summary of Water Pressure

LEVEL ALONG TRANSVERSE FORCE- KN M ( Kn - m )
Load
L.A L.A
Condition Load(t) Load(t) HL HT
(m) ML (m) MT ML MT
INT HFL 1.27 2.36 3.01 6.36 2.36 15.03 1.27 6.36 3.01 15.03
LWL 1.27 2.36 3.01 6.36 2.36 15.03 1.27 6.36 3.01 15.03
TOF HFL 3.34 6.20 20.72 16.71 6.20 103.6 3.34 16.71 20.72 103.6
LWL 3.34 6.20 20.72 16.71 6.20 103.6 3.34 16.71 20.72 103.6
BOF HFL 6.59 32.93 27.33 136.6
Calculation as Given Above
LWL 6.59 32.93 27.33 136.6

8 SEISMIC FORCE
8.1 Seismic Coefficients

As per IRS Seismic Code

Pier height inc. pier cap above pier foundation = 12.52 m

8.1.1 Longitudinal SEISMIC COEFFICIENTS

Rocky Sa/g= 2.500 0.0<= T <=0.40
2.670 0.40<= T <=4.0

Medium Soil Sa/g= 2.500 0.0<= T <=0.55

Design of Substructure for Br. No. 395 106 of 218

Br NO 395-R2 PN2
3.631 0.550<= T <=4.0

Soft Soil Sa/g= 2.500 0.0<= T <=0.670

4.46 0.670<= T <=4.0

Shape (1 = Circular, 2= Rec) 2

Width of Section = 1500 mm
Depth of Straight Portion =4800 mm
IL = 4800x1500^3 +/ 124 3.14 x1500^4 / 64
IL = 1.5984E+12 mm

DL Reactions = 88 t

LL Reactions = 177.812 t

Length ( L ) = 12516 mm
Grade of Concrete= 35
2
Modulus of elasticity E= 31000 N/mm
4
Moment of Inertia I = 1.598E+12 mm
Deflection ( d ) 1 mm
Horizontal Deflection, for Cantilever structure
3
d= PL
3 EI
3
P= d *3EI / L = 75817 N

Max Length of Br = 61.35

Max Length of Span 12.27

Response Reduction Factor4= ( As per Table-3 )- IRS Seismic Code

Importance Factor = 1.5 ZONE FACTOR
Zone No = IV
Zone Factor = 0.24 IRS-Seismic Code
D.L & L.L of Super Structure =2658.9 kN Zone No a
Period (T) = 0.375 II 0.1 0.1
P= 75817 N III 0.16 0.16
Type of Soil = Rocky IV 0.24 0.24
Sa/g = 2.500 V 0.36 0.36
Horizontal Coefficients = 0.1125

8.1.2 Transverse SEISMIC COEFFICIENTS

Rocky Sa/g= 2.500 0.0<= T <=0.40
8.34 0.40<= T <=4.0

Medium Soil Sa/g= 2.500 0.0<= T <=0.55

11.35 0.550<= T <=4.0

Soft Soil Sa/g= 2.500 0.0<= T <=0.670

13.93 0.670<= T <=4.0

Shape (1 = Circular, 2= Rec) 2

Width of Section = 1500 mm
Depth of Straight Portion = 4800 mm

Design of Substructure for Br. No. 395 107 of 218

Br NO 395-R2 PN2
IT =
IT =
1500x4800^3/12 ( 4 x1500^4 / 128 )(PI
+ 2 * (3.14 + (*750^2/2)*2,000^2 )
IT = 1.5606E+13 mm

Diameter = 1500 mm
IL = 3.14 x1500^4 / 644
2.4838E+11 mm

Length ( L ) = 12516 mm
Grade of Concrete= 35 DL Reactions = 88 t
2
Modulus of elasticity E= 31000 N/mm
LL Reactions = 178 t
4
Moment of Inertia I = 1.561E+13 mm
Deflection ( d ) 1 mm
Horizontal Deflection, for Cantilever structure
d= PL
3

3 EI
P = d *3EI /=L 740238 N
Response Reduction Factor = 4 ( As per Table-3 )- IRS Seismic Code
Importance Factor = 1.5
Zone No = IV
Zone Factor = 0.24
D.L & L.L of Super Structure = 2658.9 kN
Period (T) = 0.120
P= 740238 N
Type of Soil = Rocky
Sa/g = 2.500
Horizontal Coefficients = 0.1125

For Foundation
Response Reduction factor = R = 2 ( As per Table-3 )- IRS Seismic Code
Ratio of R for FND /STEM LONG = 4.0 / 2 = 2
Ratio of R for FND /STEM Trans = 4.0 / 2 = 2

As per Cl 7.2.1 of IRS Seismic Code ( 30 % Extra Taken in Separate Calculation)

Ah(longitudinal)= ELx +0.3 ELy = 0.113 + 0.0 x 0.113 = 0.113

Ah(transverse)= ELx +0.3 ELy = 0.113 + 0.0 x 0.113 = 0.113

Except FND For FND

Ah(longitudinal)= 0.113 0.225
Ah(transverse)= 0.113 0.225
Ah(vertical)= 0.075 0.150

Total Reaction Total Reaction

Bearing DL SIDL FPLL OSL TSL with OSL -KN with TSL-KN
KN KN KN KN KN Along Trans Along Trans
B1 112 108.7 31.5 468 494 252 720 252 746
B2 112 108.7 31.5 375 395 252 626 252 647
B3 111.5 108.7 31.5 0.000 494 252 252 252 746
B4 111.5 108.7 31.5 0.000 395 252 252 252 647

Design of Substructure for Br. No. 395 108 of 218

Br NO 395-R2 PN2

Assumptions
1- For Calculating Seismic Force on Live Load, Max Vertical Load Condition will be considered
2- Seismic Force will be considered separately for 1 Span Loaded & Both Span Loaded condition
It is assumed that only 50 % Live Load Present during Seismic, with Cl. 7.1- IRS Sub Str code
3- Transverse Seismic
4- No Live Load has been considered for Along Seismic
Max Vertical Load Case for 1 Span Loaded Case = OSL3
Max Vertical Load Case for 2 Span Loaded Case = TSL1

Seismic LOAD for - WITH OSL

Horz Seismic Force
Bearing

Bearing

Vertical Except Foundation Foundation

Reaction Along Seismic Trans Seismic Vertic Along Seismic Trans Seismic Vertic
Coff

Along Trans al Along Transverse al

Coff Along Trans 0.113 0.113 0.075 0.225 0.225 0.150
UNIT KN KN KN KN KN KN KN KN
B1 1 252 720 28.3 81.0 54.0 56.6 162.0 108.0
B2 1 252 626 28.3 70.5 47.0 56.6 140.9 94.0
B3 1 252 252 28.3 28.3 18.9 56.6 56.6 37.8
B4 1 252 252 28.3 28.3 18.9 56.6 56.6 37.8
TOTAL 113.3 208.1 139 226.5 416.2 277

Seismic Force for Pier Cap

Weight of Pier Cap = 490.4 KN

Seismic LOAD for - Pier Cap

Horz Seismic Force
Except Foundation Foundation
Weight of Pier Cap Along Seismic Trans Seismic Vertic Along Seismic Trans Seismic Vertic
Along Trans al Along Transverse al
0.113 0.113 0.075 0.225 0.225 0.150
KN KN KN KN KN KN KN
490 55.2 55.2 36.8 110.3 110.3 73.6

Seismic LOAD for - WITH TSL

Horz Seismic Force
Bearing

Bearing

Vertical
Except Foundation Foundation
Along Seismic Trans Seismic Vertic Along Seismic Trans Seismic
Reaction Vertic
Coff

Along Trans al Along Transverse al

Coff Along Trans 0.113 0.113 0.075 0.225 0.225 0.150
UNIT KN KN KN KN KN KN KN
B1 1 252 746 28.3 83.9 55.9 56.6 167.8 111.8
B2 1 252 647 28.3 72.8 48.5 56.6 145.5 97.0
B3 1 252 746 28.3 83.9 55.9 56.6 167.8 111.8
B4 1 252 647 28.3 72.8 48.5 56.6 145.5 97.0
TOTAL -RIGHT 56.6 156.7 104 113.3 313.3 209
TOTAL -LEFT 56.6 156.7 104 113.3 313.3 209

SEISMIC Force - Top of FOUNDATION

Top of Bearing -L- = 30.203 Top of Bearing -R- = 30.203

Design of Substructure for Br. No. 395 109 of 218

Br NO 395-R2 PN2
Top of Foundation 17.647
RL of CG of Pier CAP = 29.680 Bottom of Pier CAP = 29.163
Height between Bearing- L and INT CHK LVL = 12.556 m
Height between Bearing- R and INT CHK LVL = 12.556 m
Height between Pier Cap CG & INT CHK LVL = 12.033 m

Weight of Stem between Pier Cap & TOF = 2411.882 KN

CG of STEM above TOF = 5.758 m

TOF
Submerged Height -H 9.300 9.300
Hydrodyna

Rad. of Enveloping Cylinder-a 3.150 0.750 Fig 7 Sub Str.

mic Effect

Height / Radius Ratio 2.952 12.400

Coefficient, Ce 0.675 0.730 Table 5 Sub Str.
Wt of Enveloping Cylinder, W e-KN 2897.568 164.261 2
p a H gw

Trans
Along Trans Along Vertic Along Transverse
verse Ver Load
Load Load Ecc al Ht Moment Moment
Load CASE Ecce
Hx Hy ex ey H1 V Hx*H1+V*ex Hy*H1+V*ey
Kn KN m m m KN Mx My
WITH OSL 113.3 208.1 0.289 0.000 12.56 138.7 1462.3 2613.1
WITH TSL- RIGHT 56.6 156.7 0.289 0.000 12.56 104.4 741.3 1966.9
WITH TSL- Left 56.6 156.7 -0.289 0.000 12.56 104.4 680.9 1966.9
PIER CAP 55.2 55.2 0.000 0.000 12.56 18.9 692.8 692.8
STEM 271.3 271.3 0.000 0.000 5.758 180.9 1562.4 1562.4
Hydrodynamic Force 326.0 18.5 0.000 0.000 4.650 0.0 1515.8 85.9
TOTAL WITH OSL 765.8 553.1 338.5 5233.2 4954.2
TOTAL WITH TSL 765.8 658.3 408.6 5193.1 6274.9

As per Cl 7.3 -IRS Seismic Code

Long Force = Elx+0.3Ely
Trans Force = Ely+0.3Ely

Final Seismic Force at TOF

Condition Vert Hx Hy ML MT
Long Seismic - (OSL) + 338.5 931.7 0 6719 0
Long Seismic - (TSL) + 408.6 963.2 0 7076 0
Trans Seismic - (OSL) + 338.5 0 782.8 0 6524
Trans Seismic - (TSL) + 408.6 0 888 0 7833

SEISMIC FORCE - Bottom of FOUNDATION

Top of Bearing = 30.203 Top of Bearing -R- = 30.203

Top of Foundation 17.647
Bottom of Foundation 16.447
RL of CG of Pier CAP = 29.680 Bottom of Pier CAP = 29.163
Height between Bearing- L and INT CHK LVL = 13.756 m
Height between Bearing- R and INT CHK LVL = 13.756 m
Height between Pier Cap CG & INT CHK LVL = 13.233 m

Weight of Stem between Pier Cap & TOF = 2411.882 KN

CG of STEM above TOF = 5.758 m

Design of Substructure for Br. No. 395 110 of 218

Br NO 395-R2 PN2
Weight of Foundation = 2984.949 KN
CG of Foundation above TOF = 0.600 m

BOF
Submerged Height -H 10.500 10.500
Hydrodyna

Rad. of Enveloping Cylinder-a 3.150 0.750 Fig 7 Sub Str.

mic Effect

Height / Radius Ratio 3.333 14.000

Coefficient, Ce 0.730 0.730 Table 5 Sub Str.
Wt of Enveloping Cylinder, W e-KN 3271.448 185.456 2
p a H gw
Note for Hydrodynamic Force at Bottom of Foundation
1 Radius of Enveloping Cylinder up to Top of Foundation Taken
2 Weight of Cylinder in Foundation Portion has been ignored
3 Moment From Bottom of Foundation has been taken

Trans
Along Trans Along Vertic Along Transverse
verse Ver Load
Load Load Ecc al Ht Moment Moment
Load CASE Ecce
Hx Hy ex ey H1 V Hx*H1+V*ex Hy*H1+V*ey
Kn KN m m m KN Mx My
WITH OSL 113 208 0.289 0.000 13.76 138.7 1598.2 2862.9
WITH TSL- RIGHT 57 157 0.289 0.000 13.76 104.4 809.2 2154.9
WITH TSL- Left 57 157 -0.289 0.000 13.76 104.4 748.9 2154.9
PIER CAP 55 55 0.000 0.000 13.23 18.9 730.1 730.1
STEM 271 271 0.000 0.000 6.958 180.9 1888.0 1888.0
FOUNDATION 336 336 0.000 0.000 0.600 223.9 201.5 201.5
Hydrodynamic Force 368 21 0.000 0.000 5.250 0.0 1932.2 109.5
TOTAL WITH OSL 1144 891 562.4 6350.0 5792.0
TOTAL WITH TSL 1144 996 632.5 6309.9 7239.0

As per Cl 7.3 -IRS Seismic Code

Long Force = Elx+0.3Ely
Trans Force = Ely+0.3Ely

Final Seismic Force at BOF

Condition Vert Hx Hy ML MT
Long Seismic - (OSL) + 562.4 1411 0 8088 0
Long Seismic - (TSL) + 632.5 1443 0 8482 0
Trans Seismic - (OSL) + 562.4 0 1234 0 7697
Trans Seismic - (TSL) + 632.5 0 1340 0 9132

LL OSL 6.69 4.125 27.6 0.000 0.000 0.00 0.000 14.58 0.0

SUMMARY OF LOAD

DETAILING OF PIER STEM

a Calculation of Minimum Vertical Reinforcement

a1 As per Cl 15.9.4 CBC

Min Reinforcement Area = 0.15 * Pu/ fy

Pu = Max Ultimate axial Load = 6554 T = 6554022 N

Design of Substructure for Br. No. 395 111 of 218

Br NO 395-R2 PN2
fy = 500 Mpa

2
Min Area required = 0.150 x 6554022 = 1966 mm
500
Min % of Area = 1966 x 100.00 / 8377500 = 0.023 %

As per Cl Min % of Steel will be lesser of 1% of above

Min % of Steel = 0.023 %

a2 As per Appendix- B Cl B-3 IRS Seismic Code

Ductile Detailing ( 1 = YES, 2 = NO ) = 1

Min % of Vertical Steel For ductile Detailing = 0.8 %

a3 Practical Consideration

Length / Thickness = 4.800 / 1.500 = 3.2

Type = COLUMN

Min % of Vertical Steel For Practical Consideration = 0.6 %

Final Min % of Steel = 0.800 %

b Ties

b1 As per Concrete Bridge Code

Type of Pier Shaft = COLUMN

Cl No 15.9.4.3 will be applicable

As per Clause

Provided Spacing =100 mm c/c

Min Dia of Bar = 25 / 4 = 6 mm

Provided Bar Dia = 16 mm

Max Allowed Spacing = 25 x 16 = 300 mm ( Max 300 mm )

b2 As per IRS Seismic Code- App B Cl B5.5

Design of Substructure for Br. No. 395 112 of 218

Br NO 395-R2 PN2

For Rectangular/Square X-Section

Cl B 5.5.2

Gross Area of of X- Section = Ag = 1500 x 4800 = 7200000 mm2

Core Area of X- Section = Ak = 1400 x 4700 = 6580000 mm2

fck = 35 fy = 500

Longer Dimension = h = 4700 mm Spacing = S = 100 mm

Total Area of Hoops & Cross Ties

Ash
=

Max of 1 & 2 below

2.5
1- Ash = 0.24 ShAg fck
-1
Ak fy

2
Ash = 7200000 35 744 mm
112800 -1 =
6580000 500

2
2- Ash = 0.096 Sh * fck/fy = 35 3158 mm
45120 x =
500
Spacing of Transverse Reinforcement ( Cl B 5.4 )

Min of Following

1- 1/5th of Least Lateral Dimension =1500 / 5= 300 mm

2- 6 times Dia of Bar = 6 x 25 = 150 mm

3- Max 150 mm = 150 mm

Provide Spacing = 150 mm

Final Transverse Reinforcement

1- In Confining Zone ( H/4 ) from Top of Slab

Outer Ring #REF! #@ 100

Link Dia 16
Vertical Spacing 100
Horizontal Spacing 200

2- Above Confining Zone

Outer Ring 16 #@ 100

Link Dia 16
Vertical Spacing 100
Horizontal Spacing 200

Design of Substructure for Br. No. 395 113 of 218

Br NO 395-R2 PN2

TOP OF FOUNDATION
CALCULATIONS FOR LOADING AT TOP OF FOUNDATION

Sl. No Vertic Hzl. - Hzl. -

ML MT
Description al X Z
Factor KN KN KN KN-m KN-m
BASIC LOADS
0 0 0 0 0 0
1 DEAD LOADS
1a Dead Load DL2+ 3350 0.0 0.0 0.0 0.0
1b Super Imposed Deed Load SIDL + 434.7 0.0 0.0 0.0 0.0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 126.1 0.0 0.0 0.0 0.0
2b Max Longitudinal Moment Condition ML(L1)+ 1686 491 0 6646 0
2c Max Transverse Moment Condition MT(L2)+ 1005 491 0 6449 0
2d Max Resultant Moment Condition MR(L3)+ 1686 491 0 6646 0
2e Min Vertical Load Condition V(L4) 0 0 0 0 0
2f Max Vertical Load Condition V(L5) 1778 491 0 6646 0
2g Max Longitudinal Horz. Load Condition HL(L6) 1005 491 0 6449 0
2h Max Transverse Horz. Load Condition Ht(L7) 1005 491 0 6449 0
3 LWR FORCE
3a LWR FORCE + 1 0 0 0 0 0
4 WATER CURRENT FORCES
4a Water CURRENT FORCES - HFL W(HFL )+ -779 3 17 21 104
4b Water CURRENT FORCES - LWL W(LWL )+ -779 3 17 21 104
5 Seismic Force
5a Long Seismic - (OSL) + LS-O 339 932 0 6719 0
5b Long Seismic - (TSL) + LS-T 409 963 0 7076 0
5c Trans Seismic - (OSL) + TS-O 339 0 783 0 6524
5d Trans Seismic - (TSL) + TS-T 409 0 888 0 7833
5e Span Dislodged - Long Seismic LS-SD 0.000 0.000 0.000 0.000 0.000
6 Force Due To WIND
6a WIND(OSL) + 0.00
WI-O 0.00 0.00 0.00 0.0
6b WIND(TSL) + 0.00
WI-T 0.00 0.00 0.00 0.0
COMBINATION LOADS
1 2 3 4 5 6 7 8 9 10 11 12

SR No Description V HL HT ML MT

UNFACTORED - -BASIC- COMB-1

1 1 DL2+ 1 SIDL + 1 FPLL+ 1 ML(L1)+ 1 W(HFL )+ 4818 494 17 6667 104

2 1 DL2+ 1 SIDL + 1 FPLL+ 1 MT(L2)+ 1 W(HFL )+ 4137 494 17 6470 104

3 1 DL2+ 1 SIDL + 1 FPLL+ 1 MR(L3)+ 1 W(HFL )+ 4818 494 17 6667 104

4 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L4) 1 W(HFL )+ 3132 3 17 21 104

5 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L5) 1 W(HFL )+ 4910 494 17 6667 104

Design of Substructure for Br. No. 395 114 of 218

Br NO 395-R2 PN2

6 1 DL2+ 1 SIDL + 1 FPLL+ 1 HL(L6) 1 W(HFL )+ 4137 494 17 6470 104

7 1 DL2+ 1 SIDL + 1 FPLL+ 1 Ht(L7) 1 W(HFL )+ 4137 494 17 6470 104

8 1 DL2+ 1 SIDL + 1 FPLL+ 1 ML(L1)+ 1 W(LWL )+ 4818 494 17 6667 104

9 1 DL2+ 1 SIDL + 1 FPLL+ 1 MT(L2)+ 1 W(LWL )+ 4137 494 17 6470 104

10 1 DL2+ 1 SIDL + 1 FPLL+ 1 MR(L3)+ 1 W(LWL )+ 4818 494 17 6667 104

11 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L4) 1 W(LWL )+ 3132 3 17 21 104

12 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L5) 1 W(LWL )+ 4910 494 17 6667 104

13 1 DL2+ 1 SIDL + 1 FPLL+ 1 HL(L6) 1 W(LWL )+ 4137 494 17 6470 104

14 1 DL2+ 1 SIDL + 1 FPLL+ 1 Ht(L7) 1 W(LWL )+ 4137 494 17 6470 104

UNFACTORED- - LONG SEISMIC- HFL - Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

15 3455 791 11 8969 69
W(HFL )+ 0.67 LS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

16 3045 812 11 9075 69
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

17 3502 812 11 9207 69
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

18 2372 648 11 4755 69
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

19 3564 812 11 9207 69
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

20 3045 812 11 9075 69
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

21 3045 812 11 9075 69
W(HFL )+ 0.67 LS-T

UNFACTORED- - LONG SEISMIC- LWL- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

22 3455 791 11 8969 69
W(LWL )+ 0.67 LS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

23 3045 812 11 9075 69
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

24 3502 812 11 9207 69
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

25 2372 648 11 4755 69
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

26 3564 812 11 9207 69
W(LWL )+ 0.67 LS-T

Design of Substructure for Br. No. 395 115 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

27 3045 812 11 9075 69
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

28 3045 812 11 9075 69
W(LWL )+ 0.67 LS-T

UNFACTORED- - TRANS SEISMIC- HFL - Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

29 3455 167 536 4467 4441
W(HFL )+ 0.67 TS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

30 3045 167 606 4335 5317
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

31 3502 167 606 4467 5317
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

32 2372 2 606 14 5317
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

33 3564 167 606 4467 5317
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

34 3045 167 606 4335 5317
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

35 3045 167 606 4335 5317
W(HFL )+ 0.67 TS-T

UNFACTORED- - TRANS SEISMIC- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
LWL- COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

36 3455 167 536 4467 4441
W(LWL )+ 0.67 TS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

37 3045 167 606 4335 5317
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

38 3502 167 606 4467 5317
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

39 2372 2 606 14 5317
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

40 3564 167 606 4467 5317
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

41 3045 167 606 4335 5317
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

42 3045 167 606 4335 5317
W(LWL )+ 0.67 TS-T

UNFACTORED- - WIND- HFL - COMB-2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

43 3228 331 11 4467 69
W(HFL )+ 0.67 WI-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

44 2772 331 11 4335 69
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

45 3228 331 11 4467 69
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

46 2098 2 11 14 69
W(HFL )+ 0.67 WI-T

Design of Substructure for Br. No. 395 116 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

47 3290 331 11 4467 69
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

48 2772 331 11 4335 69
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

49 2772 331 11 4335 69
W(HFL )+ 0.67 WI-T

UNFACTORED- - WIND- LWL - COMB-2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

50 3228 331 11 4467 69
W(LWL )+ 0.67 WI-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

51 2772 331 11 4335 69
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

52 3228 331 11 4467 69
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

53 2098 2 11 14 69
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

54 3290 331 11 4467 69
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

55 2772 331 11 4335 69
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

56 2772 331 11 4335 69
W(LWL )+ 0.67 WI-T

UNFACTORED- - LWR- HFL - COMB-3

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

57 3228 331 11 4467 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

58 2772 331 11 4335 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

59 3228 331 11 4467 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

60 2098 2 11 14 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

61 3290 331 11 4467 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

62 2772 331 11 4335 69
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

63 2772 331 11 4335 69
W(HFL )+ 0.67 1

UNFACTORED- - LWR- LWL - COMB-3

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

64 3228 331 11 4467 69
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

65 2772 331 11 4335 69
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

66 3228 331 11 4467 69
W(LWL )+ 0.67 1

Design of Substructure for Br. No. 395 117 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

67 2098 2 11 14 69
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

68 3290 331 11 4467 69
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

69 2772 331 11 4335 69
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

70 2772 331 11 4335 69
W(LWL )+ 0.67 1

Summary of UNFACORED Combination

5 Governing - Max. Axial load 4910 494 17 6667 104

17 Governing - Max. Long. Moment 3502 812 11 9207 69

16 Governing - Max. Trans. moment 3045 167 606 4335 5317

46 Governing - Min Vertical 2098 2 11 14 69

SLS - -BASIC- COMB-1

1 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 5074 543 17 7331 104

2 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 4324 543 17 7115 104

3 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 5074 543 17 7331 104

4 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 3219 3 17 21 104

5 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 5175 543 17 7331 104

6 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 4324 543 17 7115 104

7 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 4324 543 17 7115 104

8 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 5074 543 17 7331 104

9 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 4324 543 17 7115 104

10 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 5074 543 17 7331 104

11 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 3219 3 17 21 104

12 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 5175 543 17 7331 104

Design of Substructure for Br. No. 395 118 of 218

Br NO 395-R2 PN2

13 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 4324 543 17 7115 104

14 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 4324 543 17 7115 104

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

SLS- - LONG SEISMIC- HFL - COMB-2
with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

15 5412 1205 17 14051 104
LS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

16 4733 1236 17 14190 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

17 5482 1236 17 14407 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 LS-

18 3628 967 17 7096 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 LS-

19 5584 1236 17 14407 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

20 4733 1236 17 14190 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

21 4733 1236 17 14190 104
LS-T

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

SLS- - LONG SEISMIC- LWL- COMB-2
with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

22 5412 1205 17 14051 104
LS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

23 4733 1236 17 14190 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

24 5482 1236 17 14407 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1 LS-

25 3628 967 17 7096 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1 LS-

26 5584 1236 17 14407 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

27 4733 1236 17 14190 104
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

28 4733 1236 17 14190 104
LS-T

SLS- - TRANS SEISMIC- HFL - COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

29 5412 273 800 7331 6628
TS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

30 4733 273 905 7115 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

31 5482 273 905 7331 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 TS-

32 3628 3 905 21 7936
T

Design of Substructure for Br. No. 395 119 of 218

Br NO 395-R2 PN2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 TS-

33 5584 273 905 7331 7936
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

34 4733 273 905 7115 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

35 4733 273 905 7115 7936
TS-T

SLS- - TRANS SEISMIC- LWL- COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

36 5412 273 800 7331 6628
TS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

37 4733 273 905 7115 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

38 5482 273 905 7331 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1

39 3628 3 905 21 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1

40 5584 273 905 7331 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

41 4733 273 905 7115 7936
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

42 4733 273 905 7115 7936
TS-T

SLS- - WIND- HFL - COMB-2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

43 5074 543 17 7331 104
WI-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

44 4324 543 17 7115 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

45 5074 543 17 7331 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 WI-

46 3219 3 17 21 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 WI-

47 5175 543 17 7331 104
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

48 4324 543 17 7115 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

49 4324 543 17 7115 104
WI-T

SLS- - WIND- LWL - COMB-2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

50 5074 543 17 7331 104
WI-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

51 4324 543 17 7115 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

52 5074 543 17 7331 104
WI-T

Design of Substructure for Br. No. 395 120 of 218

Br NO 395-R2 PN2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1

53 3219 3 17 21 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1

54 5175 543 17 7331 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

55 4324 543 17 7115 104
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

56 4324 543 17 7115 104
WI-T

SLS- - LWR- HFL - COMB-3

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

57 5074 543 17 7331 104
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

58 4324 543 17 7115 104
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

59 5074 543 17 7331 104
1

60 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 1 3219 3 17 21 104

61 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 1 5175 543 17 7331 104

62 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1 1 4324 543 17 7115 104

63 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1 1 4324 543 17 7115 104

SLS- - LWR- LWL - COMB-3

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

64 5074 543 17 7331 104
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

65 4324 543 17 7115 104
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

66 5074 543 17 7331 104
1

67 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1 1 3219 3 17 21 104

68 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1 1 5175 543 17 7331 104

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

69 4324 543 17 7115 104
1

70 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1 1 4324 543 17 7115 104

Summary of SLS Combination

19 Governing - Max. Axial load 5584 1236 17 14407 104

6735

17 Governing - Max. Long. Moment 5482 1236 17 14407 104

6812

Design of Substructure for Br. No. 395 121 of 218

Br NO 395-R2 PN2

16 Governing - Max. Trans. moment 4733 273 905 7115 7936

4 Governing - Min Vertical 3219 3 17 21 104

ULS - -BASIC- COMB-1

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 ML(L1)+ 1 W(HFL

1 7418 862 17 11651 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MT(L2)+ 1 W(HFL

2 6226 862 17 11307 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MR(L3)+ 1 W(HFL

3 7418 862 17 11651 104
)+

4 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L4) 1 W(HFL )+ 4467 3 17 21 104

5 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L5) 1 W(HFL )+ 7579 862 17 11651 104

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 HL(L6) 1 W(HFL

6 6226 862 17 11307 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 Ht(L7) 1 W(HFL

7 6226 862 17 11307 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 ML(L1)+ 1 W(LWL

8 7418 862 17 11651 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MT(L2)+ 1 W(LWL

9 6226 862 17 11307 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MR(L3)+ 1 W(LWL

10 7418 862 17 11651 104
)+

11 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L4) 1 W(LWL )+ 4467 3 17 21 104

12 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L5) 1 W(LWL )+ 7579 862 17 11651 104

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 HL(L6) 1 W(LWL

13 6226 862 17 11307 104
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 Ht(L7) 1 W(LWL

14 6226 862 17 11307 104
)+

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

ULS- - LONG SEISMIC- HFL - COMB-2
with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

15 7220 1511 17 17724 104
)+ 1.25 LS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

16 6353 1551 17 17894 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

17 7307 1551 17 18170 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

18 4947 1207 17 8865 104
1.25 LS-T

Design of Substructure for Br. No. 395 122 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

19 7436 1551 17 18170 104
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

20 6353 1551 17 17894 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

21 6353 1551 17 17894 104
)+ 1.25 LS-T

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

ULS- - LONG SEISMIC- LWL- COMB-2
with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

22 7220 1511 17 17724 104
)+ 1.25 LS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

23 6353 1551 17 17894 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

24 7307 1551 17 18170 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

25 4947 1207 17 8865 104
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

26 7436 1551 17 18170 104
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

27 6353 1551 17 17894 104
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

28 6353 1551 17 17894 104
)+ 1.25 LS-T

ULS- - TRANS SEISMIC- HFL - COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

29 7220 347 995 9325 8259
)+ 1.25 TS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

30 6353 347 1127 9049 9895
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

31 7307 347 1127 9325 9895
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

32 4947 3 1127 21 9895
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

33 7436 347 1127 9325 9895
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

34 6353 347 1127 9049 9895
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

35 6353 347 1127 9049 9895
)+ 1.25 TS-T

ULS- - TRANS SEISMIC- LWL- COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

36 7220 347 995 9325 8259
)+ 1.25 TS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

37 6353 347 1127 9049 9895
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

38 7307 347 1127 9325 9895
)+ 1.25 TS-T

Design of Substructure for Br. No. 395 123 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

39 4947 3 1127 21 9895
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

40 7436 347 1127 9325 9895
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

41 6353 347 1127 9049 9895
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

42 6353 347 1127 9049 9895
)+ 1.25 TS-T

ULS- - WIND- HFL - COMB-2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

43 6797 690 17 9325 104
)+ 1.25 WI-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

44 5842 690 17 9049 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

45 6797 690 17 9325 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

46 4436 3 17 21 104
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

47 6925 690 17 9325 104
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

48 5842 690 17 9049 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

49 5842 690 17 9049 104
)+ 1.25 WI-T

ULS- - WIND- LWL - COMB-2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

50 6797 690 17 9325 104
)+ 1.25 WI-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

51 5842 690 17 9049 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

52 6797 690 17 9325 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

53 4436 3 17 21 104
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

54 6925 690 17 9325 104
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

55 5842 690 17 9049 104
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

56 5842 690 17 9049 104
)+ 1.25 WI-T

ULS- - LWR- HFL - COMB-3

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

57 6797 690 17 9325 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

58 5842 690 17 9049 104
)+ 1.25 1

Design of Substructure for Br. No. 395 124 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

59 6797 690 17 9325 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

60 4436 3 17 21 104
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

61 6925 690 17 9325 104
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

62 5842 690 17 9049 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

63 5842 690 17 9049 104
)+ 1.25 1

ULS- - LWR- LWL - COMB-3

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

64 6797 690 17 9325 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

65 5842 690 17 9049 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

66 6797 690 17 9325 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

67 4436 3 17 21 104
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

68 6925 690 17 9325 104
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

69 5842 690 17 9049 104
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

70 5842 690 17 9049 104
)+ 1.25 1

Summary of ULS Combination

5 Governing - Max. Axial load 7579 862 17 11651 104

17 Governing - Max. Long. Moment 7307 1551 17 18170 104

16 Governing - Max. Trans. moment 6353 347 1127 9049 9895

46 Governing - Min Vertical 4436 3 17 21 104

Design of Substructure for Br. No. 395 125 of 218

Br NO 395-R2 PN2

BOTTOM OF FOUNDATION
CALCULATIONS FOR LOADING AT BOTTOM OF FOUNDATION

Vertic Hzl. - Hzl. -

ML MT
Sl. No Description al X Z
Factor t t t t-m t-m
BASIC LOADS
0 0 0 0 0 0
1 DEAD LOADS
1a Dead Load DL2+ 6335 0.0 0.0 0.0 0.0
1b Super Imposed Deed Load SIDL + 435 0.0 0.0 0.0 0.0
2 LIVE LOADS
2a Footpath Live Load FPLL+ 126.1 0.0 0.0 0.0 0.0
2b Max Longitudinal Moment Condition ML(L1)+ 1686 491 0 0 7235
2c Max Transverse Moment Condition MT(L2)+ 1005 491 0 0 7038
2d Max Resultant Moment Condition MR(L3)+ 1686 491 0 0 7235
2e Min Vertical Load Condition V(L4) 0 0 0 0 0
2f Max Vertical Load Condition V(L5) 1778 491 0 0 7235
2g Max Longitudinal Horz. Load Condition HL(L6) 1005 491 0 0 7038
2h Max Transverse Horz. Load Condition Ht(L7) 1005 491 0 0 7038
3 LWR FORCE
3a LWR FORCE + 1 0 0 0 0 0
4 WATER CURRENT FORCES
4a Water CURRENT FORCES - HFL W(HFL )+ -1029 6.59 32.93 27.33 136.63
4b Water CURRENT FORCES - LWL W(LWL )+ -779.1 6.59 32.93 27.33 136.63
5 Seismic Force
5a Long Seismic - (OSL) + LS-O 562 1411 0 8088 0
5b Long Seismic - (TSL) + LS-T 633 1443 0 8482 0
5c Trans Seismic - (OSL) + TS-O 562 0 1234 0 7697
5d Trans Seismic - (TSL) + TS-T 633 0 1340 0 9132
5e Span Dislodged - Long Seismic LS-SD 0.000 0.000 0.000 0.000 0.000
6 Force Due To WIND
6a WIND(OSL) + WI-O 0 0 0 0 0
6b WIND(TSL) + WI-T 0 0 0 0 0
COMBINATION LOADS
1 2 3 4 5 6 7 8 9 10 11 12
SR No Description V HL HT ML MT

UNFACTORED - -BASIC- COMB-1

1 1 DL2+ 1 SIDL + 1 FPLL+ 1 ML(L1)+ 1 W(HFL )+ 7553 497 33 27 7371

2 1 DL2+ 1 SIDL + 1 FPLL+ 1 MT(L2)+ 1 W(HFL )+ 6872 497 33 27 7174

3 1 DL2+ 1 SIDL + 1 FPLL+ 1 MR(L3)+ 1 W(HFL )+ 7553 497 33 27 7371

4 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L4) 1 W(HFL )+ 5867 7 33 27 137

5 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L5) 1 W(HFL )+ 7645 497 33 27 7371

6 1 DL2+ 1 SIDL + 1 FPLL+ 1 HL(L6) 1 W(HFL )+ 6872 497 33 27 7174

Design of Substructure for Br. No. 395 126 of 218

Br NO 395-R2 PN2

7 1 DL2+ 1 SIDL + 1 FPLL+ 1 Ht(L7) 1 W(HFL )+ 6872 497 33 27 7174

8 1 DL2+ 1 SIDL + 1 FPLL+ 1 ML(L1)+ 1 W(LWL )+ 7803 497 33 27 7371

9 1 DL2+ 1 SIDL + 1 FPLL+ 1 MT(L2)+ 1 W(LWL )+ 7122 497 33 27 7174

10 1 DL2+ 1 SIDL + 1 FPLL+ 1 MR(L3)+ 1 W(LWL )+ 7803 497 33 27 7371

11 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L4) 1 W(LWL )+ 6117 7 33 27 137

12 1 DL2+ 1 SIDL + 1 FPLL+ 1 V(L5) 1 W(LWL )+ 7895 497 33 27 7371

13 1 DL2+ 1 SIDL + 1 FPLL+ 1 HL(L6) 1 W(LWL )+ 7122 497 33 27 7174

14 1 DL2+ 1 SIDL + 1 FPLL+ 1 Ht(L7) 1 W(LWL )+ 7122 497 33 27 7174

UNFACTORED- - LONG SEISMIC- HFL - Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

15 5437 1114 22 5437 4939
W(HFL )+ 0.67 LS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

16 5028 1135 22 5701 4807
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

17 5484 1135 22 5701 4939
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

18 4355 971 22 5701 92
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

19 5546 1135 22 5701 4939
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

20 5028 1135 22 5701 4807
W(HFL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

21 5028 1135 22 5701 4807
W(HFL )+ 0.67 LS-T

UNFACTORED- - LONG SEISMIC- LWL- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

22 5605 1114 22 5437 4939
W(LWL )+ 0.67 LS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

23 5195 1135 22 5701 4807
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

24 5652 1135 22 5701 4939
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

25 4522 971 22 5701 92
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

26 5714 1135 22 5701 4939
W(LWL )+ 0.67 LS-T

Design of Substructure for Br. No. 395 127 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

27 5195 1135 22 5701 4807
W(LWL )+ 0.67 LS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

28 5195 1135 22 5701 4807
W(LWL )+ 0.67 LS-T

UNFACTORED- - TRANS SEISMIC- HFL - Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

29 5437 169 849 18 10096
W(HFL )+ 0.67 TS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

30 5028 169 920 18 10925
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

31 5484 169 920 18 11057
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

32 4355 4 920 18 6210
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

33 5546 169 920 18 11057
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

34 5028 169 920 18 10925
W(HFL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

35 5028 169 920 18 10925
W(HFL )+ 0.67 TS-T

UNFACTORED- - TRANS SEISMIC- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
LWL- COMB-2 with Seismic

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

36 5605 169 849 18 10096
W(LWL )+ 0.67 TS-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

37 5195 169 920 18 10925
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

38 5652 169 920 18 11057
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

39 4522 4 920 18 6210
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

40 5714 169 920 18 11057
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

41 5195 169 920 18 10925
W(LWL )+ 0.67 TS-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

42 5195 169 920 18 10925
W(LWL )+ 0.67 TS-T

UNFACTORED- - WIND- HFL - COMB-2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

43 5061 333 22 18 4939
W(HFL )+ 0.67 WI-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

44 4604 333 22 18 4807
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

45 5061 333 22 18 4939
W(HFL )+ 0.67 WI-T

Design of Substructure for Br. No. 395 128 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

46 3931 4 22 18 92
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

47 5122 333 22 18 4939
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

48 4604 333 22 18 4807
W(HFL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

49 4604 333 22 18 4807
W(HFL )+ 0.67 WI-T

UNFACTORED- - WIND- LWL - COMB-2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

50 5228 333 22 18 4939
W(LWL )+ 0.67 WI-O

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

51 4772 333 22 18 4807
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

52 5228 333 22 18 4939
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

53 4098 4 22 18 92
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

54 5290 333 22 18 4939
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

55 4772 333 22 18 4807
W(LWL )+ 0.67 WI-T

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

56 4772 333 22 18 4807
W(LWL )+ 0.67 WI-T

UNFACTORED- - LWR- HFL - COMB-3

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

57 5061 333 22 18 4939
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

58 4604 333 22 18 4807
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

59 5061 333 22 18 4939
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

60 3931 4 22 18 92
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

61 5122 333 22 18 4939
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

62 4604 333 22 18 4807
W(HFL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

63 4604 333 22 18 4807
W(HFL )+ 0.67 1

UNFACTORED- - LWR- LWL - COMB-3

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 ML(L1)+ 0.67

64 5228 333 22 18 4939
W(LWL )+ 0.67 1

Design of Substructure for Br. No. 395 129 of 218

Br NO 395-R2 PN2

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MT(L2)+ 0.67

65 4772 333 22 18 4807
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 MR(L3)+ 0.67

66 5228 333 22 18 4939
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L4) 0.67

67 4098 4 22 18 92
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 V(L5) 0.67

68 5290 333 22 18 4939
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 HL(L6) 0.67

69 4772 333 22 18 4807
W(LWL )+ 0.67 1

0.67 DL2+ 0.67 SIDL + 0.67 FPLL+ 0.67 Ht(L7) 0.67

70 4772 333 22 18 4807
W(LWL )+ 0.67 1

Summary of UNFACORED Combination

12 Governing - Max. Axial load 7895 497 33 27 7371

16 Governing - Max. Long. Moment 5028 1135 22 5701 4807

17 Governing - Max. Trans. moment 5484 169 920 18 11057

46 Governing - Min Vertical 3931 4 22 18 92

SLS - -BASIC- COMB-1

1 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 7809 546 33 27 8095

2 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 7059 546 33 27 7878

3 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 7809 546 33 27 8095

4 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 5954 7 33 27 137

5 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 7910 546 33 27 8095

6 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 7059 546 33 27 7878

7 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 7059 546 33 27 7878

8 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 8059 546 33 27 8095

9 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 7309 546 33 27 7878

Design of Substructure for Br. No. 395 130 of 218

Br NO 395-R2 PN2

10 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 8059 546 33 27 8095

11 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 6204 7 33 27 137

12 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 8160 546 33 27 8095

13 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 7309 546 33 27 7878

14 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 7309 546 33 27 7878

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

SLS- - LONG SEISMIC- HFL - COMB-2
with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

15 8371 1687 33 8115 8095
LS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

16 7692 1719 33 8509 7878
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

17 8441 1719 33 8509 8095
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 LS-

18 6586 1449 33 8509 137
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 LS-

19 8542 1719 33 8509 8095
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

20 7692 1719 33 8509 7878
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

21 7692 1719 33 8509 7878
LS-T

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

SLS- - LONG SEISMIC- LWL- COMB-2
with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

22 8621 1687 33 8115 8095
LS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

23 7942 1719 33 8509 7878
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

24 8691 1719 33 8509 8095
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1 LS-

25 6836 1449 33 8509 137
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1 LS-

26 8792 1719 33 8509 8095
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

27 7942 1719 33 8509 7878
LS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

28 7942 1719 33 8509 7878
LS-T

SLS- - TRANS SEISMIC- HFL - COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

Design of Substructure for Br. No. 395 131 of 218

Br NO 395-R2 PN2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

29 8371 276 1267 27 15792
TS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

30 7692 276 1373 27 17010
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

31 8441 276 1373 27 17227
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 TS-

32 6586 7 1373 27 9269
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 TS-

33 8542 276 1373 27 17227
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

34 7692 276 1373 27 17010
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

35 7692 276 1373 27 17010
TS-T

SLS- - TRANS SEISMIC- LWL- COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

36 8621 276 1267 27 15792
TS-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

37 7942 276 1373 27 17010
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

38 8691 276 1373 27 17227
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1

39 6836 7 1373 27 9269
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1

40 8792 276 1373 27 17227
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

41 7942 276 1373 27 17010
TS-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

42 7942 276 1373 27 17010
TS-T

SLS- - WIND- HFL - COMB-2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

43 7809 546 33 27 8095
WI-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

44 7059 546 33 27 7878
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

45 7809 546 33 27 8095
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 WI-

46 5954 7 33 27 137
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 WI-

47 7910 546 33 27 8095
T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1

48 7059 546 33 27 7878
WI-T

Design of Substructure for Br. No. 395 132 of 218

Br NO 395-R2 PN2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1

49 7059 546 33 27 7878
WI-T

SLS- - WIND- LWL - COMB-2

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

50 8059 546 33 27 8095
WI-O

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

51 7309 546 33 27 7878
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

52 8059 546 33 27 8095
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1

53 6204 7 33 27 137
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1

54 8160 546 33 27 8095
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

55 7309 546 33 27 7878
WI-T

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1

56 7309 546 33 27 7878
WI-T

SLS- - LWR- HFL - COMB-3

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(HFL )+ 1

57 7809 546 33 27 8095
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(HFL )+ 1

58 7059 546 33 27 7878
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(HFL )+ 1

59 7809 546 33 27 8095
1

60 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(HFL )+ 1 1 5954 7 33 27 137

61 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(HFL )+ 1 1 7910 546 33 27 8095

62 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(HFL )+ 1 1 7059 546 33 27 7878

63 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(HFL )+ 1 1 7059 546 33 27 7878

SLS- - LWR- LWL - COMB-3

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 ML(L1)+ 1 W(LWL )+ 1

64 8059 546 33 27 8095
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MT(L2)+ 1 W(LWL )+ 1

65 7309 546 33 27 7878
1

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 MR(L3)+ 1 W(LWL )+ 1

66 8059 546 33 27 8095
1

67 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L4) 1 W(LWL )+ 1 1 6204 7 33 27 137

Design of Substructure for Br. No. 395 133 of 218

Br NO 395-R2 PN2

68 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 V(L5) 1 W(LWL )+ 1 1 8160 546 33 27 8095

1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 HL(L6) 1 W(LWL )+ 1

69 7309 546 33 27 7878
1

70 1 DL2+ 1.2 SIDL + 1 FPLL+ 1.1 Ht(L7) 1 W(LWL )+ 1 1 7309 546 33 27 7878

Summary of SLS Combination

26 Governing - Max. Axial load 8792 1719 33 8509 8095

6735

16 Governing - Max. Long. Moment 7692 1719 33 8509 7878

6812

17 Governing - Max. Trans. moment 8441 276 1373 27 17227

4 Governing - Min Vertical 5954 7 33 27 137

ULS - -BASIC- COMB-1

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 ML(L1)+ 1 W(HFL

1 10899 865 33 27 12797
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MT(L2)+ 1 W(HFL

2 9707 865 33 27 12453
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MR(L3)+ 1 W(HFL

3 10899 865 33 27 12797
)+

4 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L4) 1 W(HFL )+ 7949 7 33 27 137

5 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L5) 1 W(HFL )+ 11060 865 33 27 12797

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 HL(L6) 1 W(HFL

6 9707 865 33 27 12453
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 Ht(L7) 1 W(HFL

7 9707 865 33 27 12453
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 ML(L1)+ 1 W(LWL

8 11149 865 33 27 12797
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MT(L2)+ 1 W(LWL

9 9957 865 33 27 12453
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 MR(L3)+ 1 W(LWL

10 11149 865 33 27 12797
)+

11 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L4) 1 W(LWL )+ 8199 7 33 27 137

12 1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 V(L5) 1 W(LWL )+ 11310 865 33 27 12797

Design of Substructure for Br. No. 395 134 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 HL(L6) 1 W(LWL

13 9957 865 33 27 12453
)+

1.25 DL2+ 2 SIDL + 1.5 FPLL+ 1.75 Ht(L7) 1 W(LWL

14 9957 865 33 27 12453
)+

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

ULS- - LONG SEISMIC- HFL - COMB-2
with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

15 10981 2114 33 10137 10265
)+ 1.25 LS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

16 10114 2153 33 10629 9989
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

17 11068 2153 33 10629 10265
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

18 8708 1810 33 10629 137
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

19 11197 2153 33 10629 10265
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

20 10114 2153 33 10629 9989
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

21 10114 2153 33 10629 9989
)+ 1.25 LS-T

Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered

ULS- - LONG SEISMIC- LWL- COMB-2
with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

22 11231 2114 33 10137 10265
)+ 1.25 LS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

23 10364 2153 33 10629 9989
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

24 11318 2153 33 10629 10265
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

25 8958 1810 33 10629 137
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

26 11447 2153 33 10629 10265
1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

27 10364 2153 33 10629 9989
)+ 1.25 LS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

28 10364 2153 33 10629 9989
)+ 1.25 LS-T

ULS- - TRANS SEISMIC- HFL - COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

29 10981 350 1576 27 19886
)+ 1.25 TS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

30 10114 350 1707 27 21404
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

31 11068 350 1707 27 21680
)+ 1.25 TS-T

Design of Substructure for Br. No. 395 135 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

32 8708 7 1707 27 11552
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

33 11197 350 1707 27 21680
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

34 10114 350 1707 27 21404
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

35 10114 350 1707 27 21404
)+ 1.25 TS-T

ULS- - TRANS SEISMIC- LWL- COMB- Note:- As per Cl 2.8.5 Br Rule, HL/2 has been Considered
2 with Seismic

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

36 11231 350 1576 27 19886
)+ 1.25 TS-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

37 10364 350 1707 27 21404
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

38 11318 350 1707 27 21680
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

39 8958 7 1707 27 11552
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

40 11447 350 1707 27 21680
1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

41 10364 350 1707 27 21404
)+ 1.25 TS-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

42 10364 350 1707 27 21404
)+ 1.25 TS-T

ULS- - WIND- HFL - COMB-2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

43 10278 693 33 27 10265
)+ 1.25 WI-O

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

44 9324 693 33 27 9989
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

45 10278 693 33 27 10265
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

46 7917 7 33 27 137
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

47 10406 693 33 27 10265
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

48 9324 693 33 27 9989
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

49 9324 693 33 27 9989
)+ 1.25 WI-T

ULS- - WIND- LWL - COMB-2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

50 10528 693 33 27 10265
)+ 1.25 WI-O

Design of Substructure for Br. No. 395 136 of 218

Br NO 395-R2 PN2

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

51 9574 693 33 27 9989
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

52 10528 693 33 27 10265
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

53 8167 7 33 27 137
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

54 10656 693 33 27 10265
1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

55 9574 693 33 27 9989
)+ 1.25 WI-T

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

56 9574 693 33 27 9989
)+ 1.25 WI-T

ULS- - LWR- HFL - COMB-3

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(HFL

57 10278 693 33 27 10265
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(HFL

58 9324 693 33 27 9989
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(HFL

59 10278 693 33 27 10265
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(HFL )+

60 7917 7 33 27 137
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(HFL )+

61 10406 693 33 27 10265
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(HFL

62 9324 693 33 27 9989
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(HFL

63 9324 693 33 27 9989
)+ 1.25 1

ULS- - LWR- LWL - COMB-3

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 ML(L1)+ 1 W(LWL

64 10528 693 33 27 10265
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MT(L2)+ 1 W(LWL

65 9574 693 33 27 9989
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 MR(L3)+ 1 W(LWL

66 10528 693 33 27 10265
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L4) 1 W(LWL )+

67 8167 7 33 27 137
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 V(L5) 1 W(LWL )+

68 10656 693 33 27 10265
1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 HL(L6) 1 W(LWL

69 9574 693 33 27 9989
)+ 1.25 1

1.25 DL2+ 2 SIDL + 1.25 FPLL+ 1.4 Ht(L7) 1 W(LWL

70 9574 693 33 27 9989
)+ 1.25 1

Design of Substructure for Br. No. 395 137 of 218

Br NO 395-R2 PN2

Summary of ULS Combination

26 Governing - Max. Axial load 11447 2153 33 10629 10265

16 Governing - Max. Long. Moment 10114 2153 33 10629 9989

17 Governing - Max. Trans. moment 11068 350 1707 27 21680

46 Governing - Min Vertical 7917 7 33 27 137

Summary of Load and Moments-BOTTOM OF FOUNDATION

Governing Load Case

Result. Result.
Vertic Hzl. - Hzl. -
Condit ML MT Momen Horz
Description ion
al X Z
t Force

KN KN KN KN-m KN-m Kn-m KN-m

ACTUAL-UNFACTORED
12 Governing - Max. Axial load 7895 497 33 27 7371 7371 498
16 Governing - Max. Long. Moment 5028 1135 22 5701 4807 7457 1135
17 Governing - Max. Trans. moment 5484 169 920 18 11057 11057 935
46 Governing - Min Vertical 3931 4 22 18 92 93 23
SLS
26 Governing - Max. Axial load 8792 1719 33 8509 8095 11744 1719
16 Governing - Max. Long. Moment 7692 1719 33 8509 7878 11596 1719
17 Governing - Max. Trans. moment 8441 276 1373 27 17227 17227 1400
4 Governing - Min Vertical 5954 7 33 27 137 139 34

Analysis of Foundation Pressure ( For Open Foundation )

X
Area = A = 8.500 x 8.000 = 68 m2

Zxx = 8.000 x 8.500 2

= 96.333 m3
6
8.000

Y
Y

ZYY = 8.500 x 8.000 2

= 90.667 m3
6

8.500 SBC = 470.0 KN/m2 ( For Normal Condition )

2
SBC = 587.5 KN/m ( For Wind & Seismic Condition )
Allowable Eccentricity = b / 4
X
Allowable eL = 8.500 / 4 = 2.125 m
Allowable eT = 8.000 / 4 = 2.00 m

Design of Substructure for Br. No. 395 138 of 218

Br NO 395-R2 PN2

Summary of Result at Bottom of Foundation

S.NO Load
P ML MT P/A ML/Zxx MT/Zyy Pmax Pmin eL eT
Case Result
No KN KN-m KN-m KN/m2 KN/m2 KN/m2 KN/m2 KN/m2 m m
1 12 7895 27 7371 116 0 81 198 35 0.00 0.93 OK
2 16 5028 5701 4807 74 59 53 186 -38 1.13 0.96 REDIST
3 17 5484 18 10907 81 0 120 201 -40 0.00 1.99 REDIST
4 46 3931 18 92 58 0 1 59 57 0.00 0.02 OK
Normalised Stress ( Wing/Seismic/LWR /1.25 ) = 201.1 -39.8 1.134 1.989
Over All Result = REDISTRIBUTION

Case eL Avg Pr
L' = L - B' =B - Eff Area A' =
Pmax = 4*P
eT
P 2 eL 2 eT L'*B' / 3*A' CHK KN/m2
12 0.00 0.93 7895.1 8.493 6.133 52.0855 202.2 OK 116.1
16 1.13 0.96 5027.8 6.232 6.088 37.9413 176.7 OK 73.94
17 0.00 1.99 5484.4 8.493 4.022 34.1644 214.1 OK 80.65
46 0.00 0.02 3930.9 8.491 7.953 67.5300 62.1 OK 57.81
Normalised Stress ( Wing/Seismic/LWR /1.25 ) = 214.1 OK
Over All Result = OK

Foundation Pressure- SLS Condition

S.NO Load
P ML MT P/A ML/Zxx MT/Zyy Pmax Pmin
Case
No KN KN-m KN-m KN/m2 KN/m2 KN/m2 KN/m2 KN/m2
1 26 8792 8509 8095 129 88 89 307 -48
2 16 7692 8509 7878 113 88 87 288 -62
3 17 8441 27 17227 124 0 190 314 -66
4 4 5954 27 137 88 0 2 89 86

Governing Load Case = 17

Pmax = 314.42 KN/m2
Pmin = -66.15 KN/m2

Width of Footing = 8.500 m

2
Change of Pressure/ Length = 380.6 / 8.500 = 44.77 KN/m

Projection of Foundation = 3.500 m

2
Reduction in Foundation Pr up to Face of Pier = 44.77 x 3.500 = 156.7 KN/m

2
Foundation Pressure at Pier Face = 314.4 - 156.7 = 157.7 KN/m

2
Average Pressure = 236.1 Kn/m

2
Upward Moment = 236.1 x 3.500 = 1446 KN-m
2

2
Downward Moment due to SW = 21.25 x 3.500 = 130.2 KN-m
2
Net Moment = 1446 - 130.2 = 1316 KN-m

Moment due to Live Load = 438.6 KN-m

Design of Substructure for Br. No. 395 139 of 218

Br NO 395-R2 PN2

Summary of Load and Moments- BOF- ULS Condition

Result.
Vertic Hzl. - Hzl. - Result.
Load Case
Governing

Sr. No ML MT Momen
Description al X Z
t
Horz

KN KN KN KN-m KN-m KN-m Kn-m

1 26 Governing - Max. Axial load 11447 2153 33 10629 10265 14777 2153
2 16 Governing - Max. Long. Moment 10114 2153 33 10629 9989 14587 2153
3 17 Governing - Max. Trans. moment 11068 350 1707 27 21680 21680 1743
4 46 Governing - Min Vertical 7917 7 33 27 137 139 34
MAX 21680 2153

Analysis of Foundation Pressure ( For Open Foundation )

X
Area = A = 8.500 x 8.000 = 68 m2

2
Zxx = 8.000 x 8.500 = 96.333 m3
6
8.000

2
ZYY = 8.500 x 8.000 = 90.667 m3
Y
Y

8.500

Open Foundation Type = ( 1 = Normal 2= RAFT ) = 1

Summary of Result at Bottom of Foundation- ULS Condition

S.NO Load
P ML MT P/A ML/Zxx MT/Zyy Pmax Pmin eL eT
Case
No KN KN-m KN-m KN/m2 KN/m2 KN/m2 KN/m2 KN/m2 m m
1 26 11447.0 10629.3 10265.1 168.3 110.3 113.2 391.90 -55.22 0.93 0.90
2 16 10114.3 10629.3 9989.4 148.7 110.3 110.2 369.26 -71.78 1.05 0.99
3 17 11068.3 27.3 21680.0 162.8 0.28 239.1 402.17 -76.63 0.00 1.96
4 46 7917.0 27.3 136.6 116.4 0.28 1.51 118.22 114.64 0.00 0.02

Governing Load Case = 17

Pmax = 402.17 KN/m2
Pmin = -76.63 KN/m2

Design of Substructure for Br. No. 395 140 of 218

Br NO 395-R2 PN2
RCC OPEN FOUNDATION

1.200
Critical Sec For Shear

1.200
0.960

0.500
8.500
3.500

-76.63

205.0 272.6
402.2

7.140

Average Foundation Pressure 303.6

= KN/m^2 ( ULTIMATE )

Average thickness of foundation = 0.850 m

Weight of Foundation ( 1m width ) = 0.850 x 25.00 = 21.25 KN/m

2
Downward Moment = 21.25 x 3.500 = 130.156 KN-m
2
Ultimate Downward Moment = 1.250 x 130.156 = 162.695 KN-m

Max Projection of Toe Slab = 3.500 m

Max Pressure = 303.6 kN/m ( Taking Unit Width in Consideration )

2
304 x 3.500
Max Moment = 2 = 1859.5 KN-m

Net Ultimate Moment = 1859.5 - 162.7 = 1696.820 KN-m

Net Ultimate Shear = 272.613 - 61.094 = 211.519 KN

Design of Substructure for Br. No. 395 141 of 218

Br NO 395-R2 PN2
Checking at Section PIER Foundation
Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 1092 mm) 200 mm
No. of legs 3 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1200 mm
Average Overall depth of the section ( In Tapering Section) hav = 850 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 877.2 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 438.6 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 1315.8
ULS-Total Moment 1696.8 kN-m
Ultimate Limit State Shear Vu = 211.5 kN
Ultimate Limit State Torsion, Tu 20.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 75 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) PIER Foundation

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 8042.48 2184.00 OK
2 ULS Moment resistance KN-m 1696.82 3378.19 OK
3 Crack Width mm 0.171 0.25 OK
4 Stress in Steel Mpa 165.81 375.00 OK
5 Stress in Concrete Mpa 8.44 17.5 OK
6 Area of Shear Reinforcement mm2 235.62 0.0 OK
7 Torsional Shear Stress and Capacity Mpa 0.240 4.43 OK

Design of Substructure for Br. No. 395 142 of 218

Br NO 395-R2 PN2
8 Longitudinal Reinforcement due to Torsion mm /mm2
8.05 0.40 OK
9 Secondary Reinforcement mm 2 1005 890.4 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A

h
cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2184.00 mm2
As provided = 8042.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1092.0 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 965.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 3378 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1225 mm
Depth of Neutral axis NA, x= 316.00 mm
Distance from to the surface of the nearest longitudinal bar acr = 96.70 mm
Calculated strain in the tension reinforcement es = 0.000829
Strain at cracking LVL- Without stiffening Eff e1 = 0.0010 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000352
Strain at cracking LVL- With stiffening Eff em = 0.0006 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 4.926E+10 mm4
Crack Width W cr = 0.1713 < 0.25 mm OK Tab-10
Stress in Steel fs = 165.81 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -8.44 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 1316 KN-m

Stress in Steel fs = 165.81 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 8.44 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.823
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.638 MPa
vc' = xs vc (2d/av) = 0.525 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2

Design of Substructure for Br. No. 395 143 of 218

Br NO 395-R2 PN2
v < vc', hence Asv reqd = 0.0 mm2
Asv prov 235.6 mm2
v = Vu / (bd) 0.194 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 38.1 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1200.0 mm
Longer Core Dim of Section y1max = 1090.0 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0462 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.240 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 5.93 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 742.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 890.4 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

Checking for Two Way Shear

2.700

1.500
0.60
6.000

4.800

Sec for two-way shear

Design of Substructure for Br. No. 395 144 of 218

Br NO 395-R2 PN2
Overall Depth of Foundation at d/2 Sec = 1.080 m
Eff Depth of Foundation at d/2 Sec = 1.005 m

Circumferential Area
2
= 5.427 m
2
2.00 x 2.70 x 1.005 = 12.060 m
2.00 x 6.00 x 1.005
2
Total= 17.487 m

svc = 0.638 mPa

Shear resistance = 17487000 x 0.638

= 11157858 N
= 11158 KN
2
Avg Pr = 116.1 KN/m
Net Area = 68.0 - 16.20 = 51.800
Total Vet Load = 116.1 x 51.80 = 6014 KN
Result = OK

Checking For Bearing Pressure

2
X-Sec area of Stem at Top of Foundation = 8.378 m

Total Vertical Load = 6014.2 KN =

Allowable Bearing Pressure = 0.4 fck = 0.400 x 35.00 = 14.00 mPa

Bearing Resistance = 8377500 x 14.00 = 117285000 N

= 117285 KN
> 6014 KN
Result OK

Design of Substructure for Br. No. 395 145 of 218

Br NO 395-R2 PN2

PIER CAP
Summary of Loading ( Bearing Load as per Calculation Above)
Ecc from C/L Ecc from Face
Bearin
DL SIDL FPLL LL-V LL-H Seismic-KN of Pier-m of Pier-m
g No
KN KN KN KN KN HL HT V eL eT eL eT
B1 111.5 108.67 31.51 937 245 28.3 83.9 55.9 0.29 0.9 0.00 0.00
B2 111.5 108.67 31.51 937 245 28.3 72.8 48.5 0.29 0.9 0.00 0.00

B3 111.5 108.67 31.51 494 110 28.3 83.9 55.9 0.29 0.9 0.00 0.00
B4 111.5 108.67 31.51 494 110 28.3 72.8 48.5 0.29 0.9 0.00 0.00

Calculation for Width of Distribution

Assumptions
1- Load From Pedestal ( Or Bearing if No Pedestal) is assumed to disperse 0.5H:1V
2- Dispersion Should be calculated up to CG of Pier Cap
3- Extra raising of Pier Cap due to non similar Super Str has been ignored

Description Left Span Right Span Unit

Depth of Cap at Pier face 1.000 1.000 m
Depth of Cap at End 0.500 0.500 m
Pedestal - Along 0.000 0.000 m
Pedestal - Across 0.000 0.000 m
Along Spacing of Girder From C/L pf Pier 0.269 0.269 m
Outer Bearing Trans Distance from C/L of Pier 0.900 0.900 m
Trans Distance of Bearing from Face of Pier 1.893 1.893 m
Depth of Cap at bearing Location 1.054 1.054 m
Width of Across Distribution under Pedestal 0.900 0.900 m
Width of Along Distribution under Pedestal 0.538 0.538 m

Description Along Across Unit

Length of Pier Cap 2.200 9.000 m
Pier - Equivalent Dimension 1.500 5.585 m
Overhang 0.350 1.708 m
Shear due to Self Wt. of Overhang- /m width 6.563 32.016 KN
Moment due to Self Wt. of Overhang- /m width 1.148 27.333 KN-m

Along Analysis

Along Moment due to Self Wt 1.148 KN-m ( Will be added to DL Moment below)
Along Shear due to Self Wt 6.563 KN-m ( Will be added to DL Shear below)
Left Span Right Span
Width of Distribution = 0.900 m 0.900 m

Moment For Unit Width Due to ---

Bearin DL SIDL FPLL LL-V Seismic
g No KN-m KN-m KN-m KN-m KN-m
B1 1.1 0.00 0.00 0.00 0.00
B2 1.1 0.00 0.00 0.00 0.00

Design of Substructure for Br. No. 395 146 of 218

Br NO 395-R2 PN2

B3 1.1 0.00 0.00 0.00 0.00

B4 1.1 0.00 0.00 0.00 0.00

SLS -Combination- For Stress Check

Bearin DL SIDL FPLL LL-V Seismic SLS Moment-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1 1.1 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 1.1
B2 1 1.1 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 1.1

B3 1 1.1 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 1.1

B4 1 1.1 1.2 0.00 1.1 0.00 1.1 0.00 1 0.00 1.1

Maximum 1.1

ULS -Combination- For RCC Design

Bearin DL SIDL FPLL LL-V Seismic ULS Moment-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1.25 1.4 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 1.4
B2 1.25 1.4 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 1.4

B3 1.25 1.4 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 1.4
B4 1.25 1.4 2 0.00 1.5 0.00 1.75 0.00 1.25 0.00 1.4

Maximum 1.4

Unfactored Shear Table

Shear For Unit Width Due to ---
Bearin
DL SIDL FPLL LL-V Seismic
g No
KN-m KN-m KN-m KN-m KN-m
B1 0.0 0.0 0.0 0.0 0.0
B2 0.0 0.0 0.0 0.0 0.0

B3 0.0 0.0 0.0 0.0 0.0

B4 0.0 0.0 0.0 0.0 0.0

Design of Substructure for Br. No. 395 147 of 218

Br NO 395-R2 PN2

ULS -Combination- For RCC Design- SHEAR

Bearin DL SIDL FPLL LL-V Seismic ULS Shear-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN
B1 1.3 0.0 2.0 0.0 1.5 0.0 1.8 0.0 1.3 0.0 0.0
B2 1.3 0.0 2.0 0.0 1.5 0.0 1.8 0.0 1.3 0.0 0.0

B3 1.3 0.0 2.0 0.0 1.5 0.0 1.8 0.0 1.3 0.0 0.0
B4 1.3 0.0 2.0 0.0 1.5 0.0 1.8 0.0 1.3 0.0 0.0

Maximum 0.0

Checking at Section PIER CAP -ALONG

Type of Design BEAM

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 20 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 12 mm
long. Spacing (max= 681 mm) 200 mm
No. of legs 6 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1000 mm
Average Overall depth of the section ( In Tapering Section) hav = 750 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

Design of Substructure for Br. No. 395 148 of 218

Br NO 395-R2 PN2

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 1.15 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 1.1 kN-m
ULS-Total Moment 1.4 kN-m
Ultimate Limit State Shear Vu = 0 kN
Ultimate Limit State Torsion, Tu 10.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) PIER CAP -ALONG

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 1884.96 1816.00 OK
2 ULS Moment resistance KN-m 1.44 707.29 OK
3 Crack Width mm 0.000 0.25 OK
4 Stress in Steel Mpa 0.71 375.00 OK
5 Stress in Concrete Mpa 0.02 17.5 OK
6 Area of Shear Reinforcement mm2 678.58 221.6 OK
7 Torsional Shear Stress and Capacity Mpa 0.030 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 1.58 0.57 OK
9 Secondary Reinforcement mm2 1005 789.6 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 1816.00 mm2
As provided = 1884.96 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 908.0 mm
CG of reinforcements, dc 72.0 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 1884.96 + 0 1885.0 mm2
Reinf. steel area provided, Ast (flexure) 1885.0 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 862.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 707 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1000 mm
Depth of Neutral axis NA, x= 151.09 mm
Distance from to the surface of the nearest longitudinal bar acr = 113.22 mm
Calculated strain in the tension reinforcement es = 0.000004
Strain at cracking LVL- Without stiffening Eff e1 = 0.0000 @cnom

Design of Substructure for Br. No. 395 149 of 218

Br NO 395-R2 PN2

Strain at cracking LVL- With stiffening Eff ets = 0.567557

Strain at cracking LVL- With stiffening Eff em = -0.5676 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 9.789E+09 mm4
Crack Width W cr = 0.0000 < 0.25 mm OK Tab-10
Stress in Steel fs = 0.71 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -0.02 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 1 KN-m

Stress in Steel fs = 0.71 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 0.02 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.861
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.418 MPa
vc' = xs vc (2d/av) = 0.360 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 221.6 mm2
Asv prov 678.6 mm2
v = Vu / (bd) 0.000 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 21.9 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 888.0 mm
Longer Outer Dim of Section hmax = 1000.0 mm
Longer Core Dim of Section y1max = 888.0 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0300 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.030 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 3.65 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 314.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 113.1 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 1.58 > 0.57 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 658.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 789.6 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

Design of Substructure for Br. No. 395 150 of 218

Br NO 395-R2 PN2
Across Analysis

Across Shear due to Self Wt 32.02 KN-m ( Will be added to DL Shear below)
Left Span Right Span
Width of Distribution = 0.538 m 0.538 m

Moment For Unit Width Due to ---

Bearin
DL SIDL FPLL LL-V Seismic
g No
KN-m KN-m KN-m KN-m KN-m
B1 0.0 0.00 0.00 0 0.00
B2 0.0 0.00 0.00 0 0.00

B3 0.0 0.00 0.00 0 0.00

B4 0.0 0.00 0.00 0 0.00

SLS -Combination- For Stress Check

Bearin DL SIDL FPLL LL-V Seismic SLS Moment-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1 0.0 1.2 0.00 1.1 0.00 1.1 0.0 1 0.00 0.0
B2 1 0.0 1.2 0.00 1.1 0.00 1.1 0.0 1 0.00 0.0

B3 1 0.0 1.2 0.00 1.1 0.00 1.1 0.0 1 0.00 0.0

B4 1 0.0 1.2 0.00 1.1 0.00 1.1 0.0 1 0.00 0.0

Maximum 0.0

ULS -Combination- For RCC Design

Bearin DL SIDL FPLL LL-V Seismic ULS Moment-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1 1.25 0.0 2 0.00 1.5 0.0 1.75 0.0 1.25 0.00 0.0
B2 1.25 0.0 2 0.00 1.5 0.0 1.75 0.0 1.25 0.00 0.0

B3 1.25 0.0 2 0.00 1.5 0.0 1.75 0.0 1.25 0.00 0.0
B4 1.25 0.0 2 0.00 1.5 0.0 1.75 0.0 1.25 0.00 0.0

Maximum 0.0

Design of Substructure for Br. No. 395 151 of 218

Br NO 395-R2 PN2
Shear in Transverse Direction
Shear For Unit Width Due to ---
Bearin
DL SIDL FPLL LL-V Seismic
g No
KN-m KN-m KN-m KN-m KN-m
B1 0.0 0.0 0.0 0.0 0.0
B2 0.0 0.0 0.0 0.0 0.0

B3 0.0 0.0 0.0 0.0 0.0

B4 0.0 0.0 0.0 0.0 0.0

ULS -Combination- For RCC Design- SHEAR

Bearin DL SIDL FPLL LL-V Seismic ULS SHEAR-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN
B1 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0
B2 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0

B3 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0
B4 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 0.0

Maximum 0.0

Torsion Due to Vert Load Diff Torsion Due to Long Load

Bearin
DL SIDL FPLL LL-V SeismicDepth of CG Long Force Torsion
g No
KN-m KN-m KN-m KN-m KN-m m KN KN-m
B1-B3 0.0 0.0 0.0 0.0 0.0 0.5 355.3 177.7
B2-B4 0.0 0.0 0.0 0.0 0.0 0.5 355.3 177.7

Bearin DL SIDL FPLL LL-V Seismic ULS Moment-

g No Factor KN-m KN-m Factor KN-m Factor KN-m Factor KN-m KN-m
B1-B3 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 310.9
B2-B4 1.25 0.0 2 0.00 1.5 0.00 1.75 0.0 1.25 0.00 310.9
Max 310.9

Design of Substructure for Br. No. 395 152 of 218

Br NO 395-R2 PN2
Checking at Section PIER CAP -ACROSS
Type of Design BEAM

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 25 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 676.9 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1000 mm
Average Overall depth of the section ( In Tapering Section) hav = 750 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 0.0 kN-m
ULS-Total Moment 0.0 kN-m
Ultimate Limit State Shear Vu = 0 kN
Ultimate Limit State Torsion, Tu 310.9 kN-m

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Design of Substructure for Br. No. 395 153 of 218

Br NO 395-R2 PN2

Summary of Output ( Detail Calculation Given below) PIER CAP -ACROSS

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 2945.24 1805.00 OK
2 ULS Moment resistance KN-m 0.00 1096.97 OK
3 Crack Width mm 0.000 0.20 OK
4 Stress in Steel Mpa 0.00 375.00 OK
5 Stress in Concrete Mpa 0.00 17.5 OK
6 Area of Shear Reinforcement mm2 392.70 221.6 OK
7 Torsional Shear Stress and Capacity Mpa 0.933 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 2.46 0.40 OK
9 Secondary Reinforcement mm2 1005 783 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A

h
cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 1805.00 mm2
As provided = 2945.24 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 902.5 mm
CG of reinforcements, dc 72.5 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 2945.24 + 0 2945.2 mm2
Reinf. steel area provided, Ast (flexure) 2945.2 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 856.2 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 1097 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1000 mm
Depth of Neutral axis NA, x= 184.01 mm
Distance from to the surface of the nearest longitudinal bar acr = 111.02 mm
Calculated strain in the tension reinforcement es = 0.000000
Strain at cracking LVL- Without stiffening Eff e1 = 0.0000 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000000
Strain at cracking LVL- With stiffening Eff em = 0.0000 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.424E+10 mm4
Crack Width W cr = 0.0000 < 0.2 mm OK Tab-10
Stress in Steel fs = 0.00 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = 0.00 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 0 KN-m

Stress in Steel fs = 0.00 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 0.00 Mpa

Design of Substructure for Br. No. 395 154 of 218

Br NO 395-R2 PN2
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.863
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.486 MPa
vc' = xs vc (2d/av) = 0.420 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 221.6 mm2
Asv prov 392.7 mm2
v = Vu / (bd) 0.000 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv -10.9 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1000.0 mm
Longer Core Dim of Section y1max = 890.0 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.9328 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd < vt Torsion Rft is Required
v + vt = 0.933 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 112.8 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 490.9 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 2.46 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 652.5 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 783 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

Design of Substructure for Br. No. 395 155 of 218

ULS Analysis : Section : Definition

1 : Pier
Name Pier
Type Concrete
Material M35
Origin Centre
Dimensions
Depth 6300.mm
Width 1500.mm
Section Area 8.967E+6mm2
Reinforcement Area 93290.mm2
Reinforcement 1.040%

Section : Cover & Links

1 : Pier
Cover 50.00mm
Link Size 16.00mm
Link Material 500

Section : Elastic Properties

1 : Pier

Effective properties of the section, ignoring reinforcement.

Geometric Centroid y 0.0mm

z 0.0mm
Area 8.967E+6mm2
Second Moments of Area Iyy 27.00E+12mm4
Izz 1.599E+12mm4
Iyz 0.0mm4
Principal Second Moments of Area Iuu 27.00E+12mm4
Izz 1.599E+12mm4
Angle 0.0°
Shear Area Factor ky 0.0
kz 0.0
Torsion Constant 5.727E+12mm4
Section Modulus Zy 8.571E+9mm3
Zz 2.131E+9mm3
Plastic Modulus Zpy 13.46E+9mm3
Zpz 3.263E+9mm3
Radius of Gyration Ry 1735.mm
Rz 422.2mm

Properties of gross section, including reinforcement.

Geometric Centroid y 636.8E-9mm

z -7.544E-6mm

Design of Substructure for Br. No. 395 156 of 218

EA 280.4E+6kN
EI EIyy 855.4E+6kNm2
EIzz 53.21E+6kNm2
EIyz 0.1099kNm2
Principal EI EIuu 855.4E+6kNm2
EIzz 53.21E+6kNm2
Angle 7.849E-9°

Maximum compressive force Nu 225300.kN

Strain at Nmax 0.0
Moment at ref. pt. for Nmax Myy 0.2398kNm
Mzz 0.005518kNm

Note: Nmax is the maximum compressive force which can be carried by the section.
This is calculated by applying a constant strain across the entire section, using
ultimate material properties.

Design of Substructure for Br. No. 395 157 of 218

Material : Concrete

1 : M35
Name M35
(Modified)
Cube fckc 35.00N/mm2
Strength
Tensile fct 2.189N/mm2
Strength
Weight Normal
Weight
Density  2.400t/m3
Elastic E 29500.N/mm2
Modulus
Poisson's  0.2000
Ratio
Coeff.  10.00E-6/°C
Thermal
Expansion
Partial m 1.500
Safety
Factor
Maximum 0.003500
Strain
ULS Parabola
Compression rectangle
Curve
ULS Tension No-tension
Curve
SLS Linear
Compression
Curve
SLS Tension No-tension
Curve
Design  0.8955
strength
factor
Aggregate 20.00mm
Size

Material : Rebar

1 : 500
Type Steel rebar
Strength fy 500.0N/mm2
Elastic Modulus E 200000.N/mm2
Hardening Modulus Eh 0.0N/mm2
Density  7.850t/m3
Poisson's Ratio  0.3000
Coeff. Thermal Expansion  12.00E-6/°C
Ductility Normal
Partial Safety Factor m 1.150
me 1.000
Maximum Strain u 0.05000
Maximum Strain ud 0.05000
Stress/Strain Curve Progressive yield

Design of Substructure for Br. No. 395 158 of 218

Loading

Applied loads
Load N Myy Mzz Note
Case
[kN] [kNm] [kNm]
1 5609. 14450. 104.0
2 5508. 14450. 104.0
3 4758. 7114. 7983.
4 3245. 21.00 104.0
5 7611. 11650. 104.0
6 7339. 18230. 104.0
7 6385. 9049. 9953.
8 4468. 21.00 104.0

Section 1 Details
1.04% reinforcement in section 1 (Pier). Check this against code requirements.

ULS Cases Analysed

Name Section Loading Prestress
Factor
1 1 : Pier L5 1.000
2 1 : Pier L6 1.000
3 1 : Pier L7 1.000
4 1 : Pier L8 1.000

Strength Analysis - Loads

Case N Myy Mzz M 
[kN] [kNm] [kNm] [kNm] [°]
1 7611. 11650. 104.0 11650. -0.5115
2 7339. 18230. 104.0 18230. -0.3269
3 6385. 9049. 9953. 13450. -47.72
4 4468. 21.00 104.0 106.1 -78.58

Strength Analysis - Summary

Governing conditions are defined as:
A - reinforcing steel tension strain limit
B - concrete compression strain limit
Effective centroid is reported relative to the reference point.

Case Eff. Eff. N M Mu M/Mu Governing Neutral Neutral

Centroid Centroid Condition Axis Axis
(y) (z) Angle Depth
[kN] [kNm] [kNm] [°] [mm]
1 -2.355E-6 1.380E-6 7611. 11650. 120600. 0.09659 B: Node 15 -5.638 1280.
2 -2.356E-6 1.381E-6 7339. 18230. 120100. 0.1517 B: Node 15 -3.601 1274.
3 -2.356E-6 1.384E-6 6385. 13450. 41000. 0.3281 B: Node 1 -87.20 329.6
4 -2.356E-6 1.391E-6 4468. 106.1 30590. 0.003469 B: Node 1 -89.49 195.5
Maxima
3 -2.356E-6 1.384E-6 6385. 13450. 41000. 0.3281 B: Node 1
Minima
4 -2.356E-6 1.391E-6 4468. 106.1 30590. 0.003469 B: Node 1

Design of Substructure for Br. No. 395 159 of 218

Strength Analysis - Details
Case Moment Description N M Warning
Angle
[°] [kN] [kNm]
-155.2 Max. compressive strain 225300. 0.001107
41.82E-9 Max. tensile strain -40560. 0.001834

1 -0.008927 Axial strength at M 219100. 11650.

Initial yield 7612. 71670.
Balanced yield 120100. 179700.
Bending strength at N=0 0.0 105400.

2 -0.005706 Axial strength at M 216100. 18230.

Initial yield 7340. 71130.
Balanced yield 120000. 179800.
Bending strength at N=0 0.0 105500.

3 -0.8329 Axial strength at M 208600. 13450.

Initial yield 6386. 27650.
Balanced yield 116700. 64930.
Bending strength at N=0 0.0 36100.

4 -1.372 Axial strength at M 225100. 106.3

Initial yield 4469. 21750.
Balanced yield 111100. 53320.
Bending strength at N=0 0.0 27760.

Design of Substructure for Br. No. 395 160 of 218

Design of Substructure for Br. No. 395 161 of 218
SLS Analysis (Stresses) : Section : Definition

1 : Pier
Name Pier
Type Concrete
Material M35
Origin Centre
Dimensions
Depth 6300.mm
Width 1500.mm
Section Area 8.967E+6mm2
Reinforcement Area 93290.mm2
Reinforcement 1.040%

Section : Cover & Links

1 : Pier
Cover 50.00mm
Link Size 16.00mm
Link Material 500

Section : Elastic Properties

1 : Pier

Effective properties of the section, ignoring reinforcement.

Geometric Centroid y 0.0mm

z 0.0mm
Area 8.967E+6mm2
Second Moments of Area Iyy 27.00E+12mm4
Izz 1.599E+12mm4
Iyz 0.0mm4
Principal Second Moments of Area Iuu 27.00E+12mm4
Izz 1.599E+12mm4
Angle 0.0°
Shear Area Factor ky 0.0
kz 0.0
Torsion Constant 5.727E+12mm4
Section Modulus Zy 8.571E+9mm3
Zz 2.131E+9mm3
Plastic Modulus Zpy 13.46E+9mm3
Zpz 3.263E+9mm3
Radius of Gyration Ry 1735.mm
Rz 422.2mm

Properties of gross section, including reinforcement.

Geometric Centroid y 636.8E-9mm

Design of Substructure for Br. No. 395 162 of 218

 z -7.544E-6mm
EA 280.4E+6kN
EI EIyy 855.4E+6kNm2
EIzz 53.21E+6kNm2
EIyz 0.1099kNm2
Principal EI EIuu 855.4E+6kNm2
EIzz 53.21E+6kNm2
Angle 7.849E-9°

Maximum compressive force Nu 225300.kN

Strain at Nmax 0.003500
Moment at ref. pt. for Nmax Myy 0.2487kNm
Mzz 0.001736kNm

Note: Nmax is the maximum compressive force which can be carried by the section.
This is calculated by applying a constant strain across the entire section, using
ultimate material properties.

Material : Concrete

1 : M35
Name M35
(Modified)
Cube fckc 35.00N/mm2
Strength
Tensile fct 2.189N/mm2
Strength
Weight Normal
Weight
Density  2.400t/m3
Elastic E 29500.N/mm2
Modulus
Poisson's  0.2000
Ratio
Coeff.  10.00E-6/°C
Thermal
Expansion
Partial m 1.500
Safety
Factor
Maximum 0.003500
Strain
ULS Parabola
Compression rectangle
Curve
ULS Tension No-tension
Curve
SLS Linear
Compression
Curve
SLS Tension No-tension
Curve
Design  0.8955
strength
factor
Aggregate 20.00mm
Size

Material : Rebar

Design of Substructure for Br. No. 395 163 of 218

1 : 500
Type Steel rebar
Strength fy 500.0N/mm2
Elastic Modulus E 200000.N/mm2
Hardening Modulus Eh 0.0N/mm2
Density  7.850t/m3
Poisson's Ratio  0.3000
Coeff. Thermal Expansion  12.00E-6/°C
Ductility Normal
Partial Safety Factor m 1.150
me 1.000
Maximum Strain u 0.05000
Maximum Strain ud 0.05000
Stress/Strain Curve Progressive yield

Loading

Applied loads
Load N Myy Mzz Note
Case
[kN] [kNm] [kNm]
1 5609. 14450. 104.0
2 5508. 14450. 104.0
3 4758. 7114. 7983.
4 3245. 21.00 104.0
5 7611. 11650. 104.0
6 7339. 18230. 104.0
7 6385. 9049. 9953.
8 4468. 21.00 104.0

Section 1 Details

Warnings
Case Notes
4 Warning: No Solution

1.04% reinforcement in section 1 (Pier). Check this against code requirements.

SLS Cases Analysed

Name Section Loading Prestress Creep Mq/Mg
Factor Coeff.
Long Term Intermediate Short Term
Term

Serviceability Analysis - Loads

Case N Myy Mzz M 
[kN] [kNm] [kNm] [kNm] [°]
1 5609. 14450. 104.0 14450. -0.4123
2 5508. 14450. 104.0 14450. -0.4123

Design of Substructure for Br. No. 395 164 of 218

 3 4758. 7114. 7983. 10690. -48.29
4 3245. 21.00 104.0 106.1 -78.58

Section Material Stresses/Strains at SLS Loads

Case Point Coordinates Notes
y z Strain Stress
[mm] [mm] [-] [N/mm²]
Maxima
3 2 745.9 2478. 273.8E-6 8.078
3 2 745.9 2478. 273.8E-6 8.078
Minima
3 33 -745.9 -2478. -587.8E-6 0.0
1 32 -750.0 -2400. -95.48E-6 0.0

Reinforcement Stresses/Strains at SLS Loads

Case Bar Coordinates Notes
y z Strain Stress
[mm] [mm] [-] [N/mm²]
Maxima
3 18 668.0 2400. 233.6E-6 46.71 500
3 18 668.0 2400. 233.6E-6 46.71 500
Minima
3 19 -668.0 -2400. -547.6E-6 -109.5 500
3 19 -668.0 -2400. -547.6E-6 -109.5 500

Design of Substructure for Br. No. 395 165 of 218

SLS Analysis (Crack) : Section : Definition

1 : Pier
Name Pier
Type Concrete
Material M35
Origin Centre
Dimensions
Depth 6300.mm
Width 1500.mm
Section Area 8.967E+6mm2
Reinforcement Area 93290.mm2
Reinforcement 1.040%

Section : Cover & Links

1 : Pier
Cover 50.00mm
Link Size 16.00mm
Link Material 500

Section : Elastic Properties

1 : Pier

Effective properties of the section, ignoring reinforcement.

Geometric Centroid y 0.0mm

z 0.0mm
Area 8.967E+6mm2
Second Moments of Area Iyy 27.00E+12mm4
Izz 1.599E+12mm4
Iyz 0.0mm4
Principal Second Moments of Area Iuu 27.00E+12mm4
Izz 1.599E+12mm4
Angle 0.0°
Shear Area Factor ky 0.0
kz 0.0
Torsion Constant 5.727E+12mm4
Section Modulus Zy 8.571E+9mm3
Zz 2.131E+9mm3
Plastic Modulus Zpy 13.46E+9mm3
Zpz 3.263E+9mm3
Radius of Gyration Ry 1735.mm
Rz 422.2mm

Properties of gross section, including reinforcement.

Geometric Centroid y 636.8E-9mm

z -7.544E-6mm

Design of Substructure for Br. No. 395 166 of 218

EA 280.4E+6kN
EI EIyy 855.4E+6kNm2
EIzz 53.21E+6kNm2
EIyz 0.1099kNm2
Principal EI EIuu 855.4E+6kNm2
EIzz 53.21E+6kNm2
Angle 7.849E-9°

Maximum compressive force Nu 225300.kN

Strain at Nmax 0.003500
Moment at ref. pt. for Nmax Myy 0.2487kNm
Mzz 0.001736kNm

Note: Nmax is the maximum compressive force which can be carried by the section.
This is calculated by applying a constant strain across the entire section, using
ultimate material properties.

Material : Concrete

1 : M35
Name M35
(Modified)
Cube fckc 35.00N/mm2
Strength
Tensile fct 2.189N/mm2
Strength
Weight Normal
Weight
Density  2.400t/m3
Elastic E 29500.N/mm2
Modulus
Poisson's  0.2000
Ratio
Coeff.  10.00E-6/°C
Thermal
Expansion
Partial m 1.500
Safety
Factor
Maximum 0.003500
Strain
ULS Parabola
Compression rectangle
Curve
ULS Tension No-tension
Curve
SLS Linear
Compression
Curve
SLS Tension No-tension
Curve
Design  0.8955
strength
factor
Aggregate 20.00mm
Size

Material : Rebar

Design of Substructure for Br. No. 395 167 of 218

1 : 500
Type Steel rebar
Strength fy 500.0N/mm2
Elastic Modulus E 200000.N/mm2
Hardening Modulus Eh 0.0N/mm2
Density  7.850t/m3
Poisson's Ratio  0.3000
Coeff. Thermal Expansion  12.00E-6/°C
Ductility Normal
Partial Safety Factor m 1.150
me 1.000
Maximum Strain u 0.05000
Maximum Strain ud 0.05000
Stress/Strain Curve Progressive yield

Loading

Applied loads
Load N Myy Mzz Note
Case
[kN] [kNm] [kNm]
1 5609. 14450. 104.0
2 5508. 14450. 104.0
3 4758. 7114. 7983.
4 3245. 21.00 104.0
5 7611. 11650. 104.0
6 7339. 18230. 104.0
7 6385. 9049. 9953.
8 4468. 21.00 104.0

Section 1 Details

Warnings
Case Notes
4 Warning: No Solution

1.04% reinforcement in section 1 (Pier). Check this against code requirements.

SLS Cases Analysed

Name Section Loading Prestress Creep Mq/Mg
Factor Coeff.
Long Term Intermediate Short Term
Term

Serviceability Analysis - Loads

Case N Myy Mzz M 
[kN] [kNm] [kNm] [kNm] [°]
1 5609. 14450. 104.0 14450. -0.4123
2 5508. 14450. 104.0 14450. -0.4123
3 4758. 7114. 7983. 10690. -48.29

Design of Substructure for Br. No. 395 168 of 218

 4 3245. 21.00 104.0 106.1 -78.58

Crack Widths at SLS Loads

Crack widths calculated at 20mm intervals

Case Face Point Coordinates Strain Em Strain E1 bt Control Bar acr Cover h
x Crack

Width
y z cmin From
[mm] [mm] [mm] [mm] [mm]
[mm] [mm]
Maxima
3 32 397 -745.9 -2478. -587.8E-6 -587.8E-6 5.389 20 83.67 65.23 Face 33 1754.
557.5 0.1295

Crack Widths at SLS Loads

Maximum Crack Width per Face
Crack widths calculated at 20mm intervals

Case Face Point Coordinates Strain Em Strain E1 bt Control Bar acr Cover h
x Crack

Width
y z cmin From
[mm] [mm] [mm] [mm] [mm]
[mm] [mm]
Maxima
3 32 32 -745.9 -2478. -587.8E-6 -587.8E-6 5.389 20 83.67 65.23 Face 33 1754.
557.5 0.1295

Design of Substructure for Br. No. 395 169 of 218

Br NO 395-R2 RN1
Project RJT-KNLS Doubling Project
Client WR-CPM-II-ADI Revision R0
Job Bridge NO 395 Abt no A1 Gr No 1
Prepared By JP Checked By VG App JG
Document No - Date -

INPUT DATA
Description Value Unit Ref/Remarks

Levels
Top of Wing Wall 30.653
Top of Foundation 18.047
Bottom of Foundation 16.447
Formation Level 30.653
R.L of Bed Level 19.447
Deepest Scour Level 19.447

Dimension
Height of Wall From Top of Foundation 12.606 m
Proposed Top Width 0.450 m
Back Batter (Equivalent for existing ) (1H:?V) 10.000
Intermediate Front Batter (1H:?V) 10.0
Second Front Batter (1H:?V) 10.0
Horz Projection of Toe ( Front ) 5.300 m
Thickness of Toe At Wall Face 1.600 m
End Thickness of Toe 0.500 m
Horz Projection of Heel ( Back ) 5.300 m
Thickness of Heel At Wall Face 1.600 m
Thickness of Heel At End 0.500 m

Loading Data
Loading Standard DFC
Type ( 1= Existing 2= New ) 2
2
Live Load Surcharge 163 KN/m
2
Dead Load Surcharge 71 KN/m

Soil
Total HT = 14.206 m
Angle of Friction of Wall with Soil (d) 11.67 Deg 0.204 rad
Angle of Repose of Soil (f) ( Back ) 35 Deg 0.611 rad
Angle of Surcharge (i) 0.000 rad
2
Cohesion (c) 10.00 KN/m
Angle of Repose of Soil (f) ( Front ) 32 Deg 0.559 rad
2
Density of Front Soil 17.000 KN/m
2
Density of Back Fill 18.000 KN/m
2
Density of Submerged Soil 17.000 KN/m
F.O.S. for Passive Earth Pressure = 3 (0, IF PASSIVE IGNORED) 3
Front Delta 0.204 rad
Angle of Back Batter (a) 0.100 rad
2
Safe Bearing Capacity 470.0 KN/m

Other
Seismic Parameter
2
Method of Seismic Calculation(1= IRS Coeff Method, 2= Response Spectrum)
Zone = a = 0.05 b = 1 i =
2
Density of Masonry 25.000 KN/m
Type of Structure ( 1 = Mass CC or Masonary , 2= RCC ) 2
Grade of Concrete fck = 35 MPa

Design of Substructure for Br. No. 395 170 of 218

Br NO 395-R2 RN1

Grade of Steel = 500 MPa

Type of Foundation ( 1 =OPEN , 2= CAP , 3= Pile, 4= U Return) 1 1
Depth of Shear Key 0.000 m
Height of Second Batter (Intermediate Level) above Top of Foundation7.303 m 1
Front Offset in Wall 0.000 m
Passive Height from Bottom of Foundation 3.000 m
Coefficient of Friction between Soil & Masonary (m) 0.500
Distance form C/L of track to Back Face of Wall 3.625 m
Width of Sleeper 2.750 m
Depth of Ballast Cushion 0.350 m
Depth From Formation Level to Top of Wall 0.000 m

Reinforcement Optimisation

Bar Layer-1 Layer-2

Location Actual/Reqd Capacity/Pro
No Dia Spac Dia Spac
INT CHK LVL
2 Back Vert 32 200 825 2785 OK
Dis-Horz 12 100 1046.8 1130.4 OK
Shear 10 Leg 5 200 221.6 392.7 OK
TOP OF FOUNDATION
Back Vert 32 200 32 100 10047 14492 OK
Dis-Horz 16 100 1566.7 2009.6 OK
Shear 10 Leg 7 200 346.2 549.8 OK
TOE
Back Vert 32 100 32 100 7929 8209 OK
Dis-Horz 16 200 751.2 1004.8 OK
Shear 12 Leg 7 200 719.5 791.7 OK
Heel
Top main 32 100 32 100 6180 8209 OK
Dis-Horz 16 200 751.2 1004.8 OK
Shear 12 Leg 8 200 867.2 904.8 OK

Summary of Output

RETURN
Sr No Item Unit Actual Permissible Result
AT INT CHECKING LVL
1 Minimum Reinforcement mm2 4825.49 2805.20 OK
2 ULS Moment resistance KN-m 825.17 2785.01 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 36.82 375.00 OK
5 Stress in Concrete Mpa 1.21 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.23 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 1130.40 1046.76 OK
AT TOP Of FOUNDATION
1 Minimum Reinforcement mm2 12867.97 5582.40 OK
2 ULS Moment resistance KN-m 10047.22 14492.04 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 87.28 375.00 OK
5 Stress in Concrete Mpa 3.39 17.50 OK
6 Area of Shear Reinforcement mm2 549.78 346.22 OK
7 Torsional Shear Stress and Capacity Mpa 0.61 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2009.60 1566.72 OK

Design of Substructure for Br. No. 395 171 of 218

Br NO 395-R2 RN1
AT TOE
1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 7929.39 8209.08 OK
3 Crack Width mm 0.20 0.20 OK
4 Stress in Steel Mpa 202.47 375.00 OK
5 Stress in Concrete Mpa 13.28 17.50 OK
6 Area of Shear Reinforcement mm2 791.68 719.52 OK
7 Torsional Shear Stress and Capacity Mpa 1.46 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1004.80 751.20 OK
AT HEEL
1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 6179.51 8209.08 OK
3 Crack Width mm 0.14 0.20 OK
4 Stress in Steel Mpa 159.12 375.00 OK
5 Stress in Concrete Mpa 10.43 17.50 OK
6 Area of Shear Reinforcement mm2 904.78 867.19 OK
7 Torsional Shear Stress and Capacity Mpa 1.73 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1004.80 751.20 OK

Sr No Item Unit Actual Permissible Result

FOUNDATION CHECKING-OPEN FOUNDATION
1 Max Foundation Pressure KN/m2 261.48 470.00 OK
2 Factor of Safety for Overturning- Normal Case 5.49 2.00 OK
3 Factor of Safety for Overturning- Seismic Case 2.27 1.50 OK
4 Factor of Safety for Sliding- Normal Case 2.03 1.50 OK
5 Factor of Safety for Sliding- Seismic Case 1.84 1.25 OK

1 Calculation of Load
1.1 Active Earth Pressure

Pa = 0.5Kawhh

Where :-
Ka = Coeff. of Active Earth Pressure
h = Height of Soil
w = Unit Weight of Soil

Cos2(f - a) 5.7.1 Sub Str

Ka = Cos2(a)Cos(a Sin(f - d)Sin(f - i 2
1 +
+ d) Cos(a+ d)Cos (a - i)

Following values are taken for calculating the active earth pressure.
Level Int. Chk & TOF BOF
Slope of Batter with Vert. a= 0.100 rad
Coff. of internal friction of Soil f= 0.611 rad
Angle of friction bet. Wall & earth d= 0.204 rad
Angle of slope of fill with Horz. i= 0.000 rad
Coff. of Active Earth Pressure Ka = 0.291

Horizontal Component of Active Earth Pressure

Pah = Pa Cos(a + d)
Acting at Y1= (h/3) above section considered

Design of Substructure for Br. No. 395 172 of 218

Br NO 395-R2 RN1

Vertical Component of Active Earth Pressure

Pav = Pa Sin(a + d)
Acting at X1 = Y1Cot (90-a) from face of Wall

1.1.1 At Int Checking Level

Height from Formation Level, h = 5.303 m
h3 = 0.000 m
Pa = 0.5 x 0.29 x 18.0 x 5.30 x 5.303 = 73.688 KN/m (Width)

Horizontal Component
Pah = 73.69 x Cos( 0.100+ 0.204 ) = 70.317 KN/m (Width)
Will act at Y1 5.303 / 3 = 1.768 m

Vertical Component
Pav = 73.69 x Sin( 0.100+ 0.204 ) = 22.031 KN/m (Width)
Will act at X1 = Y1Cot(90-a)
= 1.8 x Cot(90 -0.100 ) = 0.177 m

1.2 At Top of Foundation

Height from Formation Level, h = 12.606 m
h3 = 0.000 m
Pa = 0.5 x 0.29 x 18.0 x 12.6 x 12.61 = 416.395 KN/m (Width)

Horizontal Component
Pah = 416.4 x Cos(0.10+ 0.204 ) = 397.349 KN/m (Width)
Will act at Y2 12.61 / 3 = 4.202 m

Vertical Component
Pav = 416.40 x Sin( 0.100+ 0.204 ) = 124.493 KN/m (Width)
Will act at X2 = Y2Cot(90-a)
= 4.20 x Cot(90 -0.100 ) = 0.420 m

1.3 At Bottom of Foundation

Height from Formation Level, h = 14.206 m
h3 = 0.000 m
Pa = 0.5 x 0.3 x 18.0 x 14.2 x 14.21 = 528.80 KN/m

Horizontal Component
Pah = 528.80 x Cos(0.10 0.204 ) = 504.62 KN/m
Will act at Y2 14.21 / 3 = 4.735 m

Vertical Component
Pav = 528.80 x Sin( 0.10+ 0.204 ) = 158.101 KN/m
Will act at X 2 = Y2Cot(90-a) 4.74 x Cot(90 - 0.100 ) = 0.474 m

1.2 Surcharge Effect

(S + V) x h1 x Ka 5.8.3 of Sub Str. Code

P1 = Will act at h
(B + 2D)

Design of Substructure for Br. No. 395 173 of 218

Br NO 395-R2 RN1

Live Load Surcharge per m, S= 163.000 KN/m2

Dead Load Surcharge per m, V = 71.000 KN/m2
Width of Distribution, B = 2.750 m

1.2.1 At INT Checking Level

3.625
0.530 1.720 2.750 Formation Level
B

D 2.070

0
45

5.303
h1 3.583

Checking Level

Height, h1 = 3.583 m
Depth of Dispersion, D = 2.070 m

163.0 71.00 3.58 0.291

P1 = = ##### KN/m
2.75 4.14

Will act at h1/2 1.792 m

1.2.2 At Top of Foundation

3.625
1.261 0.989 2.750 Formation Level
B

D 1.339

0
45
12.606

h1 #####

Top of Foundation

Height, h1 = ##### m
Width of Distribution, B = 2.750 m
Depth of Dispersion, D = 1.339 m

Design of Substructure for Br. No. 395 174 of 218

Br NO 395-R2 RN1

163+ 71+ 11.62+ 0.29+ Will act at

P1 = = ##### KN/m 5.808 m
2.75+ 2.7 h1/2

1.2.3 At Bottom of Foundation

3.625
6.561 0.000 2.750 Formation Level
B

D 0.350

0
45

14.206
h1 14.21

Bottom of Foundation

Height, h1 = 14.206 m
Depth of Dispersion, D = 0.350 m

163 + 71 14.2 x 0.291

P1 = = 280.529 KN/m
2.8 x 0.7

Will act at h1/2 7.103 m

3.0 PASSIVE EARTH PRESSURE

For Calculation Of Passive Earth Pressure On Substructure Coulomb Theory Is Used

2
Pp = 0.5 Kp w h

2
Cos (f+ a)
K p= 2 Sin(f + d) Sin(f + i) 2
Cos a Cos(a - d) 1 -
Cos(a- d) Cos (a - i)

f = 0.559 rad d = 0.204 rad a = 0.000 rad i = 0.000 rad

K p= 4.859 Factor of Safety for Passive = 3
Pph = Pp Cos(d - a) Acting at (h/3) above section.
Ppv = Pp Sin(d - a) Acting at X=Y Cot(90 - a)

Considering only Horizontal component because Vertical Component will be ineffective.

3.1 At Top of Foundation

Passive Height Bed
= Lvl or Scour Lvl - TOF = 19.4- 18.0- = 1.400 m
Pp = 0.5 x 4.86 x 17.0 x 1.400 2 = 80.948 KN/m

Safe Passive Pressure = 80.95 / 3 = 26.98 KN/m

Ph = 26.98 x Cos( 0.204- 0.000 ) = 26.43 KN/m Will act @ h/3 = 0.467 m

Design of Substructure for Br. No. 395 175 of 218

Br NO 395-R2 RN1

Resisting Moment = 26.4 x 0.47 x 12.332 KN-m

3.2 At Bottom of Foundation

Passive Height Bed
= Lvl or Scour Lvl - BOF = 19.4- 16.4- 3.000 m

2
Pp = 0.5 x 4.86 17.00 3.000 = 371.70 KN/m

h1 = 3.0

5.300
3.0 x

h2 = Dsk = 0.000
Pp 35
0.000

2 2
Pp = Kp * g * (h 2 - h 1) / 2 * FOS = 0.00 KN-m

Safe Passive Pressure = 371.70 /3 = 123.90 KN/m

Ph = 123.90 x Cos(0.204- 0.000 ) = 121.34 KN/m
Will act @ h/3 = 1.000 m
Resisting Moment = 121.34 x 1.00 = 121.34 KN-m

4.0 SELF WEIGHT

4.1 At Intermediate Checking Level

FL
0.000
5 Top of Wall
0.450
Back Fill 4
0.000
1 Passive5.303
6
6

3 2 0.000

A
0.530 0.530

No. Shape Horz. Vert. Densit Weigh L.A. Mom L.A. Mom
Factor (m) (m) y t W(t) from ent W above ent W
(KN/ A (m) X (tm) A (m) Y (tm)
m3)
W1 1.0 x 0.5 x 5.3 x 25.0 x 59.659 0.755 45.060 2.652 158.19
l
Fil
e
t iv

Design of Substructure for Br. No. 395 176 of 218

Ac
Br NO 395-R2 RN1

W2 0.5 x 0.5 x 5.3 x 25.0 x 35.152 1.157 40.674 1.768 62.14

l
Fil
W3 0.5 x 0.5 x 5.3 x 25.0 x 35.152 0.354 12.427 1.768 62.14

e
t iv
W4 0.5 x 0.5 x 5.3 x 18.0 x 25.310 0.177 4.474 3.535 89.48

Ac
W5 0.5 x 0.5 x 0.0 x 18.0 x 0.000 0.177 0.000 5.303 0.00
Passiv
e W6 0.5 x 0.0 x 0.0 x 17.0 x 0.000 1.511 0.000
Sum 155.27 ##### 371.94
CG of Total Mass from A = WX /W = 102.6 / 155.3 = 0.661 m
CG of Total Mass above Int Level = WY /W = 371.9 / 155.3 = 2.395 m

FL
0.000
11 Top of Wall
Back Fill 0.450 Passive
10 9
0.000 0.000
1 5.303
1
2 13 15
0.000
2

0.530
14
5 1.400
3 1.400 7.303
4

18.05
10a 1.261 0.730 1
6a 1.100
1.600 6 7 1.600
0.500 5.300 8
0.500
6b 16.45
C
8.271 5.300
13.571

4.2 At Top of Foundation

No. Shape Horz. Vert.
Densit Weigh L.A. Mome L.A. Mome
(m) y (m) t W(t) from B nt W X above nt W Y
(KN/m (m) (tm) B (m) (tm)
3)
W1 1.0 0.5 12.6 25.0 141.8 1.5 210.7 6.3 893.9
W2 0.5 0.5 5.3 25.0 35.2 1.9 66.3 9.1 318.9
W3 1.0 0.5 7.3 25.0 96.8 2.0 191.3 3.7 353.5
l
Fil

W4 0.5 0.7 7.3 25.0 66.7 2.5 165.6 2.4 162.3

e
t iv

W5 0.5 1.3 12.6 25.0 198.6 0.8 166.9 4.2 834.7

Ac

W9 0.5 1.3 12.6 18.0 143.0 0.4 60.1 8.4 1201.9

W11 0.5 1.3 0.0 18.0 0.0 0.4 0.0 12.6 0.0
W12 0.5 0.0 0.0 17.0 0.0 2.2 0.0
Fil v e

W13 1.0 0.7 0.0 17.0 0.0 2.6 0.0

i
ss

W14 0.5
l
Pa

0.1 1.4 17.0 1.7 2.9 4.9

Sum 683.8 865.8 3765.2
CG of Total Mass from BMoment/Weight
= = WX /W = 865.8 683.8 = 1.3 m
CG of Total Mass above Top of FoundationWY
= /W = 3765.2 683.8 = 5.5 m

4.3 At Bottom of Foundation

Design of Substructure for Br. No. 395 177 of 218

Br NO 395-R2 RN1

No. Shape Horz. Vert. Densi Weig L.A. Mom L.A. Mom
(m) (m) ty ht from ent W above ent W
(KN/ W(t) C (m) X (tm) C (m) Y (tm)
m3)
W1 1 0.5 12.6 25.0 141.8
962.3 7.96.8 1120.8 5.673
W2 1 0.5 5.3 25.0 35.2
252.7 7.2
10.7 375.1 1.406
W3 1 0.5 7.3 25.0 96.8
704.4 5.37.3 508.4 3.873
W4 1 0.7 7.3 25.0 66.7
519.0 4.07.8 269.0 2.667
W5 1 1.3 12.6 25.0 198.6
1219.7 5.86.1 1152.5 7.946
W6 1 3.0 1.6 25.0 118.8
491.5 0.84.1 95.1 4.754
W6a 1 5.3 1.1 25.0 72.9
257.5 0.93.5 63.2 2.915
l
Fil
e

W6b 1 5.3 0.5 25.0 66.3

175.6 0.32.7 16.6 2.650
t iv
Ac

W7 1 5.3 1.1 25.0 72.9

731.5 0.910.0 63.2 2.915
W8 1 5.3 0.5 25.0 66.3
723.5 0.310.9 16.6 2.650
W9 1 1.3 12.6 18.0 143.0
818.1 5.7
10.0 1430.8 7.946
W10 1 5.3 12.6 18.0 1202.6
3186.9 7.92.7 9504.2 66.812
W 10a 1 5.3 1.1 18.0 52.5
92.7 1.21.8 64.7 2.915
W11 1 6.6 0.0 18.0 0.0
0.0 14.22.2 0.0 0.000
W12 1 0.0 0.0 17.0 0.0
0.0 7.5 0.000
W13 1 0.7 0.0 17.0 0.0
0.0 7.9 0.000
l
Fil

W14 1 0.1 1.4 17.0 1.7

13.7 8.2 0.098
e
iv

W15 1
ss

5.3 1.4 17.0 126.1

1377.6 10.9 7.420
Pa

W16 1 5.3 1.1 17.0 49.6

585.0 11.8 2.915
Sum 2511.7
##### 14680.0 #####
C.G. of mass from CMoment/Weight
= = WX /W = 12111.69 / 2511.7 = 4.822 m
C.G. of Total Mass above Bott of Foundation
WY= /W = 14680.043 / 2511.7 = 5.845 m

5.0 SEISMIC FORCE

Earth Pressure Due to Seismic Effect 5.12.6.1 Sub Str

ah = b x Ix ao
With Response Spectrum Method
a h = (Z/2)(Sa/g)/(R/I)= ( As per IRC 6 Cl 222.5)

Z = 0.24 I = 1.5 R = 2.5

Sa /g = 2.5

ah = 0.12 x 2.5 / 1.667 = 0.18

Final Value
a h = 0.180 a v = 0.090 ( As per Abutment Calculation )

Level Int. Chk & TOFBOF

Slope of Batter with Vert. a = 0.100 rad
f=
Coff. of internal friction of Soil 0.611 rad
Angle of friction bet. Wall &d earth
= 0.204 rad
i=
Angle of slope of fill with Horz. 0.000 rad
TOF
a tan-1a h tan-1 0.180 With (+) Pt I 1.105
l = = = 0.164
1+av 1 + 0.090 Pt II 0.595
"+" & "+"
value
Case I: With

Design of Substructure for Br. No. 395 178 of 218

 "+" & "+"
Case I: With
Br NO 395-R2 RN1
2 2
1
Ca = (1 + a v) Cos (f - a - l) x 0.434
Sin(f + d)Sin(f - i - l) =
Cosl Cos2a Cos(a + d + l 1 +
Cos(a+ d + l)Cos(a - i)
b tan-1a h tan-1 0.180 With (-) Pt I 1.154
l = = = 0.195
1-av 1 - 0.090 Pt II 0.580
"-" & "-" value
Case II: With

2 2
1
Ca = (1 + a v) Cos (f - a - l) x 0.463
Sin(f + d)Sin(f - i - l) =
Cosl Cos2a Cos(a + d + l 1 +
Cos(a+ d + l)Cos(a - i)

At Int. Chk & TOF BOF

Final Ca = 0.463 (Max Value of above, i.e., a and b)
Ka = 0.291
Dynamic Increment (Ca - Ka) = 0.171

5.1 At Intermediate Checking Level

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 27.949 2.395 66.949
DUE TO SELF WT. OF Wall SFV 13.975 0.000 0.000
2
Increment in Earth Pressure [0.5gh (Ca-Ka)] 43.402 2.652 115.081
Increment in Earth Pressure Surcharge 20.871 2.389 49.858
Total Ver Load = 13.975 KN
Total Horz Load = 92.222 KN
Total Moment = 231.888 KN-m

5.2 At Top of Foundation

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 122.781 5.506 676.081
DUE TO SELF WT. OF Wall SFV 61.390 0.000 0.000
Increment in Earth Pressure [0.5 gh2(Ca-Ka)] 245.258 6.303 1545.858
Increment in Earth Pressure Surcharge 85.865 7.744 664.973
Total Ver Load = 61.390 KN
Total Horz Load = 453.903 KN
Total Moment = 2886.912 KN-m

5.3 At Bottom of Foundation

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 420.173 5.845 2455.814
DUE TO SELF WT. OF Wall SFV 210.087 0.000 0.000
Increment in Earth Pressure [0.5 gh2(Ca-Ka)] 311.467 7.103 2212.347
Increment in Earth Pressure Surcharge 165.232 9.471 1564.856
Total Ver Load = 210.087 KN
Total Horz Load = 896.872 KN
Total Moment = 6233.017 KN-m

6 STRESS CALCULATION

6.1 At Intermediate Checking Level

LOAD L.A. Mom Ultimate Load
S.No. DESCRIPTION OF LOAD

Design of Substructure for Br. No. 395 179 of 218

Br NO 395-R2 RN1
S.No. DESCRIPTION OF LOAD Mom
VERT HORZ. ent Fac Hu Vu Mu
1 Active Earth Pressure
Horizontal Component P ah 70.32 1.77 124.30 1.70 119.54 211.31
Vertical Component P av 22.03 0.18 3.89 1.70 37.45 6.62
2 Earth Pressure due to Surcharge P h 35.43 1.79 63.49 1.70 60.24 107.93
3 Self Weight & Back Fill 155.27 102.64 1.25 194.09 128.29
TOTAL - Without Seismic 177.30 105.75 294.31 179.78 231.54 454.15
Due to seismic Effect -13.97 92.22 231.89 1.60 147.56 22.36 371.02
Combined Load with Seismic 163.33 197.97 526.20 327.33 253.90 825.2

6.1.1Stresses at Intermediate Checking Level

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2)
Load ent
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B)
Without Seismic 177.30 294.31 1.66 0.90 539.11 -304.37
1.51
With Seismic 163.33 526.20 3.22 2.47 1167.33 -951.09

Checking at Section INT CHK LVL

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 1052 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 12 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1511 mm
Average Overall depth of the section ( In Tapering Section) hav = 980 mm
Clear cover to Ast Cc = 50 mm

Design of Substructure for Br. No. 395 180 of 218

Br NO 395-R2 RN1
Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 230.83 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 63.49 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 231.89
ULS-Total Moment 825.2 kN-m
Ultimate Limit State Shear Vu = 327 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) INT CHK LVL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 4825.49 2805.20 OK
2 ULS Moment resistance KN-m 825.17 2785.01 OK
3 Crack Width mm 0.000 0.25 OK
4 Stress in Steel Mpa 36.82 375.00 OK
5 Stress in Concrete Mpa 1.21 17.5 OK
6 Area of Shear Reinforcement mm2 392.70 221.6 OK
7 Torsional Shear Stress and Capacity Mpa 0.233 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 1130 1046.76 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2805.20 mm2
As provided = 4825.49 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1402.6 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 4825.49 + 0 4825.5 mm2
Reinf. steel area provided, Ast (flexure) 4825.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1326.8 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 2785 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1511 mm
Depth of Neutral axis NA, x= 292.73 mm

Design of Substructure for Br. No. 395 181 of 218

Br NO 395-R2 RN1
Distance from to the surface of the nearest longitudinal bar acr = 109.60 mm
Calculated strain in the tension reinforcement es = 0.000234
Strain at cracking LVL- Without stiffening Eff e1 = 0.0003 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.003691
Strain at cracking LVL- With stiffening Eff em = -0.0034 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 5.591E+10 mm4
Crack Width W cr = 0.0000 < 0.25 mm OK Tab-10
Stress in Steel fs = 46.74 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -1.54 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 232 KN-m

Stress in Steel fs = 36.82 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 1.21 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.773
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.495 MPa
vc' = xs vc (2d/av) = 0.383 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 221.6 mm2
Asv prov 392.7 mm2
v = Vu / (bd) 0.233 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 138.9 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1510.6 mm
Longer Core Dim of Section y1max = 1400.6 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.233 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.03 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Design of Substructure for Br. No. 395 182 of 218

Br NO 395-R2 RN1
Eff. depth of the section 'd' for single layer d= 872.3 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 1046.76 mm2
Area of reinforcement Provided = 1130 + 0 1130 mm2

6.2 At Top of Foundation

S.No LOAD L.A. Mom Ultimate Load

DESCRIPTION OF LOAD
. VERT HORZ. (m) ent Fac Hu Vu Mu
1 Active Earth Pressure
Horizontal Component P ah 397.3 4.2 1669.7 1.7 675.5 2838
Vertical Component P av 124.5 0.4 52.3 1.7 211.6 89
2 Earth Pressure due to Surcharge P h 145.8 5.8 846.7 1.7 247.8 1439
3 Passive Earth Pressure 26.4 0.5 -12.3 1.7 44.9 -21
4 Self Weight & Back Fill 683.8 1.3 865.8 1.3 854.7 1082
TOTAL 808.3 3422.2 968.2 1066.4 5428
Due to seismic Effect -61.4 453.9 2886.9 1.6 726.2 98.2 4619
Combined Load with Seismic 746.9 6309.1 1694.5 1164.6 10047

6.2.1 Stresses at Top of Foundation

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2)

Load ent
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B)
Without Seismic808.3 3422.2 4.2 2.7 1781.9 -1237.8
3.0
With Seismic 746.9 6309.1 8.4 7.0 3785.3 -3282.5

Checking at Section AT TOP of FND

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 32 mm
Spacing in second layer 100 mm c/c
Dia of spacer bar 32 mm
dia of link 10 mm
long. Spacing (max= 2093 mm) 200 mm
No. of legs 7 nos

Design of Substructure for Br. No. 395 183 of 218

Br NO 395-R2 RN1
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 2971 mm
Average Overall depth of the section ( In Tapering Section) hav = 1486 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 1764.90 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 846.74 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 2886.91
ULS-Total Moment 10047.2 kN-m
Ultimate Limit State Shear Vu = 1694 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) AT TOP of FND

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 12867.97 5582.40 OK
2 ULS Moment resistance KN-m 10047.22 14492.04 OK
3 Crack Width mm 0.000 0.25 OK
4 Stress in Steel Mpa 87.28 375.00 OK
5 Stress in Concrete Mpa 3.39 17.5 OK
6 Area of Shear Reinforcement mm2 549.78 346.2 OK
7 Torsional Shear Stress and Capacity Mpa 0.607 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2010 1566.719996 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 5582.40 mm2
As provided = 12867.97 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for two layers d= 2791.2 mm

Design of Substructure for Br. No. 395 184 of 218

Br NO 395-R2 RN1

CG of reinforcements, dc 116.0 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 10
Reinf. steel area provided, As = 4825.49 + 8042.48 12868.0 mm2
Reinf. steel area provided, Ast (flexure) 12868.0 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 2589.0 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 14492 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 2971 mm
Depth of Neutral axis NA, x= 662.09 mm
Distance from to the surface of the nearest longitudinal bar acr = 109.60 mm
Calculated strain in the tension reinforcement es = 0.000395
Strain at cracking LVL- Without stiffening Eff e1 = 0.0004 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.001156
Strain at cracking LVL- With stiffening Eff em = -0.0007 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 5.634E+11 mm4
Crack Width W cr = 0.0000 < 0.25 mm OK Tab-10
Stress in Steel fs = 78.96 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -3.07 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 2887 KN-m

Stress in Steel fs = 87.28 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 3.39 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.700
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.546 MPa
vc' = xs vc (2d/av) = 0.382 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 346.2 mm2
Asv prov 549.8 mm2
v = Vu / (bd) 0.607 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 346.2 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 2971.2 mm
Longer Core Dim of Section y1max = 2861.2 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17

Design of Substructure for Br. No. 395 185 of 218

Br NO 395-R2 RN1
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.607 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.03 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for two layers d= 1305.6 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 1566.719996 mm2
Area of reinforcement Provided = 2010 + 0 2010 mm2

6.3 At Bottom of Foundation

S.No LOAD L.A. MomMoment (KN-m)

DESCRIPTION OF LOAD
. VERT HORZ. (m) ent Front L.A. Ms
1 Active Earth Pressure
Horizontal Component P ah 504.6 4.7 2389.5
Vertical Component P av 158.1 0.5 74.9 13.1 2070.8
2 Earth Pressure due to Surcharge P h 280.5 7.1 1992.6
3 Passive Earth Pressure 121.3 1.0 -121.3
4 Self Weight & Back Fill 2511.7 4.8 12112 9 21975
TOTAL 2669.8 663.8 16447 24045
Due to seismic Effect -210.1 6233
Combined Load with Seismic 2459.7 22680 24045

6.2.1 Stresses at Bottom of Foundation

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2) Permissible

Load ent (KN/m2)
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B) Max Min
Without Seismic
2669.8 16447 6.161 0.625 251.08 142.36 470.0 0.0
13.571
With Seismic 2459.7 22680 9.221 2.435 376.38 -13.90 626.7 0.0

Maximum Eccentricity, e = 2.435 m (Eccentricity outside middle

Effective width of foundation after redistribution of pressure
13.57(B'=B-2e)
- 2.44 - = = 8.701 m
Maximum Pressure after redistribution = 282 x 13.6 x 8.701 = 440.3 KN/m2

Design of Toe Slab

Max Projection of Toe Slab = 5.300 m

Design of Substructure for Br. No. 395 186 of 218

Br NO 395-R2 RN1

On safer side Taking Max Foundation Pressure as UDL ( Though it will be Trapezoidal )

Max Pressure = 376.380 kN/m ( Taking Unit Width in Consideration )

2
376.380 x 5.300 =
Max Moment = 5286.26
2

Ultimate Moment 1.500

= x 5286.26 = 7929.39 kN-m

Ultimate Shear, Hu = 376.4 x 3.700 x 1.5 = 2089 kN

Checking at Section TOE

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 32 mm
Spacing in second layer 100 mm c/c
Dia of spacer bar 32 mm
dia of link 12 mm
long. Spacing (max= 1069 mm) 200 mm
No. of legs 7 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Average Overall depth of the section ( In Tapering Section) hav = 800 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 3524 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 587 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 4112
ULS-Total Moment 7929 kN-m
Ultimate Limit State Shear Vu = 2089 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Design of Substructure for Br. No. 395 187 of 218

Br NO 395-R2 RN1

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) TOE

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 7929.39 8209.08 OK
3 Crack Width mm 0.195 0.20 OK
4 Stress in Steel Mpa 202.47 375.00 OK
5 Stress in Concrete Mpa 13.28 17.5 OK
6 Area of Shear Reinforcement mm2 791.68 719.5 OK
7 Torsional Shear Stress and Capacity Mpa 1.465 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1005 751.1999952 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2852.00 mm2
As provided = 16084.96 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for two layers d= 1426.0 mm
CG of reinforcements, dc 110.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 10
Reinf. steel area provided, As = 8042.48 + 8042.48 16085.0 mm2
Reinf. steel area provided, Ast (flexure) 16085.0 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1173.2 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 8209 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 490.64 mm
Distance from to the surface of the nearest longitudinal bar acr = 76.65 mm
Calculated strain in the tension reinforcement es = 0.001012
Strain at cracking LVL- Without stiffening Eff e1 = 0.0012 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000311
Strain at cracking LVL- With stiffening Eff em = 0.0009 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.520E+11 mm4
Crack Width W cr = 0.1952 < 0.2 mm OK Tab-10
Stress in Steel fs = 202.47 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -13.28 < (0.5fc) -17.5 MPa OK Tab-11

Design of Substructure for Br. No. 395 188 of 218

Br NO 395-R2 RN1

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 4112 KN-m

Stress in Steel fs = 202.47 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 13.28 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.770
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.735 MPa
vc' = xs vc (2d/av) = 0.566 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 719.5 mm2
Asv prov 791.7 mm2
v = Vu / (bd) 1.465 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 719.5 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 888.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1488.0 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 1.465 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 113.1 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.57 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for two layers d= 626.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 751.1999952 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

Design of Heel Slab

Max Projection of Heel Slab = 4.417 m (In tension Portion)

Design of Substructure for Br. No. 395 189 of 218

Br NO 395-R2 RN1

Total Weight of Soil / m Run = 12.6 x 18.00 = 226.908 kN/m

Surcharge = 145.781 kN/m

Total Vertical UDL =226.9 + 145.8 = 372.689 kN/m

Vertical UDL 372.689 kN/m ( Taking Unit Width in Consideration )

2
372.689 x 4.417 = 3635.01
Max Moment =
2

Ultimate Moment 1.700

= x 3635.01 = 6179.5 kN-m

Shear = 372.689 x 4.417 = 1646.0 KN

Ultimate Shear = 1.500 x 1646.04 = 2469.1 kN-m

Mu = 6179.5 kN-m

Checking at Section HEEL

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 32 mm
Spacing in second layer 100 mm c/c
Dia of spacer bar 32 mm
dia of link 12 mm
long. Spacing (max= 1069 mm) 200 mm
No. of legs 8 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Average Overall depth of the section ( In Tapering Section) hav = 800 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

Design of Substructure for Br. No. 395 190 of 218

Br NO 395-R2 RN1
SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 2423 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 808 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 3231
ULS-Total Moment 6180 kN-m
Ultimate Limit State Shear Vu = 2469 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) HEEL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 16084.96 2852.00 OK
2 ULS Moment resistance KN-m 6179.51 8209.08 OK
3 Crack Width mm 0.138 0.20 OK
4 Stress in Steel Mpa 159.12 375.00 OK
5 Stress in Concrete Mpa 10.43 17.5 OK
6 Area of Shear Reinforcement mm2 904.78 867.2 OK
7 Torsional Shear Stress and Capacity Mpa 1.731 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.57 OK
9 Secondary Reinforcement mm2 1005 751.1999952 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2852.00 mm2
As provided = 16084.96 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for two layers d= 1426.0 mm
CG of reinforcements, dc 110.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 10
Reinf. steel area provided, As = 8042.48 + 8042.48 16085.0 mm2
Reinf. steel area provided, Ast (flexure) 16085.0 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1173.2 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 8209 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 490.64 mm
Distance from to the surface of the nearest longitudinal bar acr = 76.65 mm
Calculated strain in the tension reinforcement es = 0.000796

Design of Substructure for Br. No. 395 191 of 218

Br NO 395-R2 RN1

Strain at cracking LVL- Without stiffening Eff e1 = 0.0009 @cnom

Strain at cracking LVL- With stiffening Eff ets = 0.000317
Strain at cracking LVL- With stiffening Eff em = 0.0006 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.520E+11 mm4
Crack Width W cr = 0.1375 < 0.2 mm OK Tab-10
Stress in Steel fs = 159.12 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -10.43 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 3231 KN-m

Stress in Steel fs = 159.12 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 10.43 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.770
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.735 MPa
vc' = xs vc (2d/av) = 0.566 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 867.2 mm2
Asv prov 904.8 mm2
v = Vu / (bd) 1.731 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 867.2 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 888.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1488.0 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 1.731 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 113.1 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.57 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for two layers d= 626.0 mm
Width of Section b= 1000.0 mm

Design of Substructure for Br. No. 395 192 of 218

Br NO 395-R2 RN1
2
Area of Secondary reinforcement require - on either side @ 0.12 % 751.1999952 mm
2
Area of reinforcement Provided = 1005 + 0 1005 mm

7 STABILITY CALCULATION
7.1 Against Overturning (Sub Structure Code Clause 5.10.1.1 and 6.8 )

Mo = Moment due to [E.P. (Horz. Component) + Surcharge (Horz. Component)]

Without seismic,
Mo = 2389.5 + 1992.6 = 4382.1 KN-m
With seismic, Mo = 2389.5 + 1992.6 + 6233.0 = 10615.14 KN-m

Ms = Moment due to [E.P. (Vert. Component) + Surcharge (Vert. Component)] +

Moment due to self Wt. & Earth Fill
Without seismic,
Ms = 24045.27 KN-m (Calculated in Table 6.3 )
With seismic, Ms = 24045.27 KN-m (Calculated in Table 6.3 )

DescriptionRestoring moment (M
Overturning
s Factor of Safety (Ms/M FOS (Reqd.)
moment (M
Without Seismic 24045.266 4382.122 5.49 2.0
With Seismic 24045.266 10615.139 2.27 1.5

7.2 Against Sliding (Sub Structure Code Clause 6.8 )

Total Horz. Force, H = 504.62 + 280.53 = 785.15 KN

Total Vert. Force, W = 2669.758 KN

Coff of Friction, m = 0.50

Base Width = 13.57 m
Cohesion, c = 10.00 KN/m2
Passive Force, P p = 121.34 KN (Ref. 9.2 )
Total Resisting Force, R = m W+Bc+P p
1334.879 + 135.712 + 121.340

= 1591.931 KN

Factor of Safety = Resisting Force 1591.9

= = 2.028 >1.5 SAFE
Horz. Force 785.1

Design of Substructure for Br. No. 395 193 of 218

Br NO 395-R2 RN2
Project RJT-KNLS Doubling Project
Client WR-CPM-II-ADI Revision R0
Job Bridge NO 395 Abt no A1 Gr No 1
Prepared By JP Checked By VG App JG
Document No - Date -

INPUT DATA
Description Value Unit Ref/Remarks

Levels
Top of Wing Wall 27.246
Top of Foundation 18.047
Bottom of Foundation 16.447
Formation Level 30.653
R.L of Bed Level 19.447
Deepest Scour Level 19.447

Dimension
Height of Wall From Top of Foundation 9.199 m
Proposed Top Width 0.450 m
Back Batter (Equivalent for existing ) (1H:?V) 10.000
Intermediate Front Batter (1H:?V) 10.0
Second Front Batter (1H:?V) 10.0
Horz Projection of Toe ( Front ) 3.600 m
Thickness of Toe At Wall Face 1.600 m
End Thickness of Toe 0.500 m
Horz Projection of Heel ( Back ) 4.000 m
Thickness of Heel At Wall Face 1.600 m
Thickness of Heel At End 0.500 m

Loading Data
Loading Standard DFC
Type ( 1= Existing 2= New ) 2
2
Live Load Surcharge 163 KN/m
2
Dead Load Surcharge 71 KN/m

Soil
Total HT = 10.799 m
Angle of Friction of Wall with Soil (d) 11.67 Deg 0.204 rad
Angle of Repose of Soil (f) ( Back ) 35 Deg 0.611 rad
Angle of Surcharge (i) 0.460 rad
2
Cohesion (c) 10.00 KN/m
Angle of Repose of Soil (f) ( Front ) 32 Deg 0.559 rad
2
Density of Front Soil 17.000 KN/m
2
Density of Back Fill 18.000 KN/m
2
Density of Submerged Soil 17.000 KN/m
F.O.S. for Passive Earth Pressure = 3 (0, IF PASSIVE IGNORED) 3
Front Delta 0.204 rad
Angle of Back Batter (a) 0.100 rad
2
Safe Bearing Capacity 470.0 KN/m

Design of Substructure for Br. No. 395 194 of 218

Br NO 395-R2 RN2

Other
Seismic Parameter
2
Method of Seismic Calculation(1= IRS Coeff Method, 2= Response Spectrum)
Zone = a = 0.05 b = 1 i =
2
Density of Masonry 25.000 KN/m
Type of Structure ( 1 = Mass CC or Masonary , 2= RCC ) 2
Grade of Concrete fck = 35 MPa
Grade of Steel = 500 MPa
Type of Foundation ( 1 =OPEN , 2= CAP , 3= Pile, 4= U Return) 1 1
Depth of Shear Key 0.000 m
Height of Second Batter (Intermediate Level) above Top of Foundation5.600 m 1
Front Offset in Wall 0.000 m
Passive Height from Bottom of Foundation 3.000 m
Coefficient of Friction between Soil & Masonary (m) 0.500
Distance form C/L of track to Back Face of Wall 10.000 m
Width of Sleeper 2.750 m
Depth of Ballast Cushion 0.350 m
Depth From Formation Level to Top of Wall 3.407 m

Reinforcement Optimisation

Bar Layer-1 Layer-2

Location Actual/Reqd Capacity/Pro
No Dia Spac Dia Spac
INT CHK LVL
2 Back Vert 32 200 270 2070 OK
Dis-Horz 16 100 842.3 2009.6 OK
Shear 10 Leg 5 200 221.6 392.7 OK
TOP OF FOUNDATION
Back Vert 32 200 3957 4351 OK
Dis-Horz 16 100 1244.3 2009.6 OK
Shear 10 Leg 5 200 309.2 392.7 OK
TOE
Back Vert 32 100 3578 4778 OK
Dis-Horz 16 200 830.4 1004.8 OK
Shear 10 Leg 7 200 389.2 549.8 OK
Heel
Top main 32 100 3327 4778 OK
Dis-Horz 16 200 830.4 1004.8 OK
Shear 10 Leg 8 200 524.1 628.3 OK

Summary of Output

RETURN
Sr No Item Unit Actual Permissible Result
AT INT CHECKING LVL
1 Minimum Reinforcement mm2 4825.49 2123.80 OK
2 ULS Moment resistance KN-m 269.52 2069.85 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 13.03 375.00 OK
5 Stress in Concrete Mpa 0.50 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 221.58 OK
7 Torsional Shear Stress and Capacity Mpa 0.14 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2009.60 842.34 OK
AT TOP Of FOUNDATION
1 Minimum Reinforcement mm2 4825.49 4363.60 OK

Design of Substructure for Br. No. 395 195 of 218

Br NO 395-R2 RN2
2 ULS Moment resistance KN-m 3956.71 4350.80 OK
3 Crack Width mm 0.00 0.25 OK
4 Stress in Steel Mpa 93.32 375.00 OK
5 Stress in Concrete Mpa 2.41 17.50 OK
6 Area of Shear Reinforcement mm2 392.70 309.16 OK
7 Torsional Shear Stress and Capacity Mpa 0.46 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2009.60 1244.28 OK
AT TOE
1 Minimum Reinforcement mm2 8042.48 2984.00 OK
2 ULS Moment resistance KN-m 3577.64 4777.59 OK
3 Crack Width mm 0.12 0.20 OK
4 Stress in Steel Mpa 193.00 375.00 OK
5 Stress in Concrete Mpa 8.20 17.50 OK
6 Area of Shear Reinforcement mm2 549.78 389.19 OK
7 Torsional Shear Stress and Capacity Mpa 0.74 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1004.80 830.40 OK
AT HEEL
1 Minimum Reinforcement mm2 8042.48 2984.00 OK
2 ULS Moment resistance KN-m 3326.71 4777.59 OK
3 Crack Width mm 0.05 0.20 OK
4 Stress in Steel Mpa 158.35 375.00 OK
5 Stress in Concrete Mpa 6.73 17.50 OK
6 Area of Shear Reinforcement mm2 628.32 524.13 OK
7 Torsional Shear Stress and Capacity Mpa 0.98 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1004.80 830.40 OK

Sr No Item Unit Actual Permissible Result

FOUNDATION CHECKING-OPEN FOUNDATION
1 Max Foundation Pressure KN/m2 261.48 470.00 OK
2 Factor of Safety for Overturning- Normal Case 4.07 2.00 OK
3 Factor of Safety for Overturning- Seismic Case 2.18 1.50 OK
4 Factor of Safety for Sliding- Normal Case 1.66 1.50 OK
5 Factor of Safety for Sliding- Seismic Case 1.51 1.25 OK

Design of Substructure for Br. No. 395 196 of 218

Br NO 395-R2 RN2

1 Calculation of Load
1.1 Active Earth Pressure

Pa = 0.5Kawh(h+2h3)

Where :-
Ka = Coeff. of Active Earth Pressure
h = Height of Soil
w = Unit Weight of Soil

Cos2(f - a) 5.7.1 Sub Str

Ka = 2
Cos (a)Cos(a Sin(f - d)Sin(f - i 2
1 +
+ d) Cos(a+ d)Cos (a - i)

Following values are taken for calculating the active earth pressure.
Level Int. Chk & TOF BOF
Slope of Batter with Vert. a= 0.100 rad
Coff. of internal friction of Soil f= 0.611 rad
Angle of friction bet. Wall & earth d= 0.204 rad
Angle of slope of fill with Horz. i= 0.000 rad
Coff. of Active Earth Pressure Ka = 0.291

Horizontal Component of Active Earth Pressure

Pah = Pa Cos(a + d)
Acting at Y1= (h/3) above section considered

Vertical Component of Active Earth Pressure

Pav = Pa Sin(a + d)
Acting at X1 = Y1Cot (90-a) from face of Wall

1.1.1 At Int Checking Level

Height from Formation Level, h = 3.778 m
h3 = 0.891 m
Pa = 0.5 x 0.29 x 18.0 x 3.78 x 5.56 = 55.038 KN/m (Width)

Horizontal Component
Pah = 55.04 x Cos( 0.100+ 0.204 ) = 52.520 KN/m (Width)
Will act at Y1 3.778 / 3 = 1.259 m

Vertical Component
Pav = 55.04 x Sin( 0.100+ 0.204 ) = 16.455 KN/m (Width)
Will act at X1 = Y1Cot(90-a)
= 1.3 x Cot(90 -0.100 ) = 0.126 m

1.2 At Top of Foundation

Height from Formation Level, h = 9.655 m
h3 = 2.277 m
Pa = 0.5 x 0.29 x 18.0 x 9.7 x 14.21 = 359.466 KN/m (Width)

Horizontal Component

Design of Substructure for Br. No. 395 197 of 218

Br NO 395-R2 RN2

Pah = 359.5 x Cos(0.10+ 0.204 ) = 343.024 KN/m (Width)

Will act at Y2 9.655 / 3 = 3.218 m

Vertical Component
Pav = 359.47 x Sin( 0.100+ 0.204 ) = 107.473 KN/m (Width)
Will act at X2 = Y2Cot(90-a)
= 3.22 x Cot(90 -0.100 ) = 0.322 m

1.3 At Bottom of Foundation

Height from Formation Level, h = 13.237 m
h3 = 3.122 m
Pa = 0.5 x 0.3 x 18.0 x 13.2 x 19.48 = 675.66 KN/m

Horizontal Component
Pah = 675.66 x Cos(0.10 0.204 ) = 644.75 KN/m
Will act at Y2 13.24 / 3 = 4.412 m

Vertical Component
Pav = 675.66 x Sin( 0.10+ 0.204 ) = 202.006 KN/m
Will act at X 2 = Y2Cot(90-a) 4.41 x Cot(90 - 0.100 ) = 0.441 m

1.2 Surcharge Effect

(S + V) x h1 x Ka 5.8.3 of Sub Str. Code

P1 = Will act at h
(B + 2D)

Live Load Surcharge per m, S= 163.000 KN/m2

Dead Load Surcharge per m, V = 71.000 KN/m2
Width of Distribution, B = 2.750 m

1.2.1 At INT Checking Level

#####
0.360 8.265 2.750 Formation Level
B

D 8.615

0
45
7.007

h1 0.000

Checking Level

Height, h1 = 0.000 m
Depth of Dispersion, D = 8.615 m

Design of Substructure for Br. No. 395 198 of 218

Br NO 395-R2 RN2

163.0 71.00 0.00 0.291

P1 = = 0.000 KN/m
2.75 17.23

Will act at h1/2 0.000 m

1.2.2 At Top of Foundation

#####
0.920 7.705 2.750 Formation Level
B

D 8.055

0
45

12.606
h1 4.901

Top of Foundation

Height, h1 = 4.901 m
Width of Distribution, B = 2.750 m
Depth of Dispersion, D = 8.055 m

163+ 71+ 4.90+ 0.29+ Will act at

P1 = = 17.70 KN/m 2.450 m
2.75+ 16.1 h1/2

1.2.3 At Bottom of Foundation

#####
4.920 3.705 2.750 Formation Level
B

D 4.055

0
45
14.206

h1 10.50

Bottom of Foundation

Height, h1 = 10.501 m
Depth of Dispersion, D = 4.055 m

163 + 71 10.5 x 0.291

P1 = = 65.874 KN/m
2.8 x 8.1

Design of Substructure for Br. No. 395 199 of 218

Br NO 395-R2 RN2

Will act at h1/2 5.250 m

3.0 PASSIVE EARTH PRESSURE

For Calculation Of Passive Earth Pressure On Substructure Coulomb Theory Is Used

2
Pp = 0.5 Kp w h

2
Cos (f+ a)
K p= 2 Sin(f + d) Sin(f + i) 2
Cos a Cos(a - d) 1 -
Cos(a- d) Cos (a - i)

f = 0.559 rad d = 0.204 rad a = 0.000 rad i = 0.000 rad

K p= 4.859 Factor of Safety for Passive = 3
Pph = Pp Cos(d - a) Acting at (h/3) above section.
Ppv = Pp Sin(d - a) Acting at X=Y Cot(90 - a)

Considering only Horizontal component because Vertical Component will be ineffective.

3.1 At Top of Foundation

Passive Height Bed
= Lvl or Scour Lvl - TOF = 19.4- 18.0- = 1.400 m
Pp = 0.5 x 4.86 x 17.0 x 1.400 2 = 80.948 KN/m

Safe Passive Pressure = 80.95 / 3 = 26.98 KN/m

Ph = 26.98 x Cos( 0.204- 0.000 ) = 26.43 KN/m Will act @ h/3 = 0.467 m
Resisting Moment = 26.4 x 0.47 x 12.332 KN-m

3.2 At Bottom of Foundation

Passive Height Bed
= Lvl or Scour Lvl - BOF = 19.4- 16.4- 3.000 m

2
Pp = 0.5 x 4.86 17.00 3.000 = 371.70 KN/m

h1 = 3.0

3.600
3.0 x

h2 = Dsk = 0.000
Pp 35
0.000

2 2
Pp = Kp * g * (h 2 - h 1) / 2 * FOS = 0.00 KN-m

Safe Passive Pressure = 371.70 /3 = 123.90 KN/m

Design of Substructure for Br. No. 395 200 of 218

Br NO 395-R2 RN2

Ph = 123.90 x Cos(0.204- 0.000 ) = 121.34 KN/m

Will act @ h/3 = 1.000 m
Resisting Moment = 121.34 x 1.00 = 121.34 KN-m

4.0 SELF WEIGHT

4.1 At Intermediate Checking Level

FL
3.407
5 Top of Wall
0.450
Back Fill 4
0.000
1 Passive3.600
6
6

3 2 0.000

A
0.360 0.360

No. Shape Horz. Vert. Densit Weigh L.A. Mom L.A. Mom
Factor (m) (m) y t W(t) from ent W above ent W
(KN/ A (m) X (tm) A (m) Y (tm)
m3)
W1 1.0 x 0.5 x 3.6 x 25.0 x 40.494 0.585 23.687 1.800 72.88
W2 0.5 x 0.4 x 3.6 x 25.0 x 16.196 0.930 15.061 1.200 19.43
l
Fil

W3 0.5 x 0.4 x 3.6 x 25.0 x 16.196 0.240 3.886 1.200 19.43

e
t iv

W4 0.5 x 0.4 x 3.6 x 18.0 x 11.661 0.120 1.399 2.400 27.98

Ac

W5 0.5 x 0.4 x 0.2 x 18.0 x 0.578 0.120 0.069 3.659 2.11

Passiv
e W6 0.5 x 0.0 x 0.0 x 17.0 x 0.000 1.170 0.000
Sum 85.12 44.103 141.84
CG of Total Mass from A = WX /W = 44.1 / 85.1 = 0.518 m
CG of Total Mass above Int Level = WY /W = 141.8 / 85.1 = 1.666 m

Design of Substructure for Br. No. 395 201 of 218

Br NO 395-R2 RN2

FL
3.407
11 Top of Wall
Back Fill 0.450 Passive
10 9
0.000 0.000
1 3.600
1
2 13 15
0.000
2

0.360
14
5 1.400
3 1.400 5.600
4

18.05
10a 0.920 0.560 1
6a 1.100
1.600 6 7 1.600
0.500 4.000 8
0.500
6b 16.45
C
6.290 3.600
9.890

4.2 At Top of Foundation

No. Shape Horz. Vert.
Densit Weigh L.A. Mome L.A. Mome
(m) y (m) t W(t) from B nt W X above nt W Y
(KN/m (m) (tm) B (m) (tm)
3)
W1 1.0 0.5 9.2 25.0 103.5 1.1 118.5 4.6 476.0
W2 0.5 0.4 3.6 25.0 16.2 1.5 24.1 6.8 110.1
W3 1.0 0.4 5.6 25.0 50.4 1.5 78.1 2.8 141.1
l
Fil

W4 0.5 0.6 5.6 25.0 39.2 1.9 75.1 1.9 73.2

e
t iv

W5 0.5 0.9 9.2 25.0 105.8 0.6 64.9 3.1 324.3

Ac

W9 0.5 0.9 9.2 18.0 76.2 0.3 23.4 6.1 467.1

W11 0.5 0.9 0.5 18.0 3.8 0.3 1.2 9.4 35.3
W12 0.5 0.0 0.0 17.0 0.0 1.7 0.0
Fil v e

W13 1.0 0.6 0.0 17.0 0.0 2.0 0.0

i
ss

W14 0.5
l
Pa

0.1 1.4 17.0 1.7 2.2 3.7

Sum 396.6 388.9 1627.0
CG of Total Mass from BMoment/Weight
= = WX /W = 388.9 396.6 = 1.0 m
CG of Total Mass above Top of FoundationWY
= /W = 1627.0 396.6 = 4.1 m

Design of Substructure for Br. No. 395 202 of 218

Br NO 395-R2 RN2

4.3 At Bottom of Foundation

No. Shape Horz. Vert. Densi Weig L.A. Mom L.A. Mom
(m) (m) ty ht from ent W above ent W
(KN/ W(t) C (m) X (tm) C (m) Y (tm)
m3)
W1 1 0.5 9.2 25.0 103.5 5.1 532.4 6.2 641.6 4.140
W2 1 0.4 3.6 25.0 16.2 5.5 88.9 8.4 136.0 0.648
W3 1 0.4 5.6 25.0 50.4 5.5 279.6 4.4 221.7 2.016
W4 1 0.6 5.6 25.0 39.2 5.9 231.9 3.5 135.9 1.568
W5 1 0.9 9.2 25.0 105.8 4.6 488.0 4.7 493.6 4.231
W6 1 2.3 1.6 25.0 91.6 3.1 288.0 0.8 73.3 3.664
W6a 1 4.0 1.1 25.0 55.0 2.7 146.7 0.9 47.7 2.200
l
Fil
e

W6b 1 4.0 0.5 25.0 50.0 2.0 100.0 0.3 12.5 2.000
t iv
Ac

W7 1 3.6 1.1 25.0 49.5 7.5 370.7 0.9 42.9 1.980

W8 1 3.6 0.5 25.0 45.0 8.1 364.0 0.3 11.3 1.800
W9 1 0.9 9.2 18.0 76.2 4.3 328.0 7.7 588.9 4.231
W10 1 4.0 9.2 18.0 662.3 2.0 1324.7 6.2 4106.1 36.796
W 10a 1 4.0 1.1 18.0 39.6 1.3 52.8 1.2 48.8 2.200
W11 1 4.9 2.4 18.0 215.9 1.6 354.0 11.6 2506.5 11.993
W12 1 0.0 0.0 17.0 0.0 5.7 0.0 0.000
W13 1 0.6 0.0 17.0 0.0 6.0 0.0 0.000
l
Fil

W14 1 0.1 1.4 17.0 1.7 6.2 10.4 0.098

eiv

W15 1
ss

3.6 1.4 17.0 85.7 8.1 693.1 5.040

Pa

W16 1 3.6 1.1 17.0 33.7 8.7 292.5 1.980

Sum 1721.1 5945.9 9066.7 86.583
C.G. of mass from CMoment/Weight
= = WX /W = 5945.86 / 1721.1 = 3.455 m
C.G. of Total Mass above Bott of Foundation
WY= /W = 9066.738 / 1721.1 = 5.268 m

5.0 SEISMIC FORCE

Earth Pressure Due to Seismic Effect 5.12.6.1 Sub Str

ah = b x Ix ao
With Response Spectrum Method
a h = (Z/2)(Sa/g)/(R/I)= ( As per IRC 6 Cl 222.5)

Z = 0.24 I = 1.5 R = 2.5

Sa /g = 2.5

ah = 0.12 x 2.5 / 1.667 = 0.18

Final Value
a h = 0.180 a v = 0.090 ( As per Abutment Calculation )

Level Int. Chk & TOFBOF

Slope of Batter with Vert. a = 0.100 rad
f=
Coff. of internal friction of Soil 0.611 rad
Angle of friction bet. Wall &d earth
= 0.204 rad
i=
Angle of slope of fill with Horz. 0.000 rad
TOF

Design of Substructure for Br. No. 395 203 of 218

Br NO 395-R2 RN2
-1
a tan-1a h tan 0.180 With (+) Pt I 1.105
l = = = 0.164
1+av 1 + 0.090 Pt II 0.595

"+" & "+"

value
Case I: With
2 2
1
Ca = (1 + a v) Cos (f - a - l) x 0.434
Sin(f + d)Sin(f - i - l) =
Cosl Cos2a Cos(a + d + l 1 +
Cos(a+ d + l)Cos(a - i)
b tan-1a h tan-1 0.180 With (-) Pt I 1.154
l = = = 0.195
1-av 1 - 0.090 Pt II 0.580
"-" & "-" value
Case II: With

2 2
1
Ca = (1 + a v) Cos (f - a - l) x 0.463
Sin(f + d)Sin(f - i - l) =
Cosl Cos2a Cos(a + d + l 1 +
Cos(a+ d + l)Cos(a - i)

At Int. Chk & TOF BOF

Final Ca = 0.463 (Max Value of above, i.e., a and b)
Ka = 0.291
Dynamic Increment (Ca - Ka) = 0.171

5.1 At Intermediate Checking Level

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 15.322 1.666 25.531
DUE TO SELF WT. OF Wall SFV 7.661 0.000 0.000
2
Increment in Earth Pressure [0.5gh (Ca-Ka)] 19.996 1.800 35.989
Increment in Earth Pressure Surcharge 0.000 0.000 0.000
Total Ver Load = 7.661 t
Total Horz Load = 35.319 t
Total Moment = 61.520 KN-m

5.2 At Top of Foundation

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 71.096 4.102 291.636
DUE TO SELF WT. OF Wall SFV 35.548 0.000 0.000
Increment in Earth Pressure [0.5 gh2(Ca-Ka)] 130.602 4.600 600.703
Increment in Earth Pressure Surcharge 10.427 3.267 34.069
Total Ver Load = 35.548 t
Total Horz Load = 212.125 t
Total Moment = 926.408 KN-m

5.3 At Bottom of Foundation

DESCRIPTION FORCE L.A. Moment
DUE TO SELF WT. OF Wall SFH 288.016 5.268 1517.270
DUE TO SELF WT. OF Wall SFV 144.008 0.000 0.000
Increment in Earth Pressure [0.5 gh2(Ca-Ka)] 179.984 5.400 971.826
Increment in Earth Pressure Surcharge 38.800 7.001 271.622
Total Ver Load = 144.008 t
Total Horz Load = 506.800 t
Total Moment = 2760.718 KN-m

6 STRESS CALCULATION

Design of Substructure for Br. No. 395 204 of 218

Br NO 395-R2 RN2

6.1 At Intermediate Checking Level

LOAD L.A. Mom Ultimate Load
S.No. DESCRIPTION OF LOAD
VERT HORZ. ent Fac Hu Vu Mu
1 Active Earth Pressure
Horizontal Component P ah 52.52 1.26 66.14 1.70 89.28 112.43
Vertical Component P av 16.46 0.13 2.07 1.70 27.97 3.52
2 Earth Pressure due to Surcharge P h 0.00 0.00 0.00 1.70 0.00 0.00
3 Self Weight & Back Fill 85.12 44.10 1.25 106.40 55.13
TOTAL - Without Seismic 101.58 52.52 112.31 89.28 134.38 171.09
Due to seismic Effect -7.66 35.32 61.52 1.60 56.51 12.26 98.43
Combined Load with Seismic 93.92 87.84 173.83 145.79 146.64 269.5

6.1.1Stresses at Intermediate Checking Level

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2) Permissible
Load ent (KN/m2)
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B) Comp Tension
Without Seismic 101.58 112.31 1.11 0.52 318.71 -145.05 #REF! #REF!
1.17
With Seismic 93.92 173.83 1.85 1.27 601.49 -440.94 #REF!

Checking at Section INT CHK LVL

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 796.4 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1170 mm

Design of Substructure for Br. No. 395 205 of 218

Br NO 395-R2 RN2

Average Overall depth of the section ( In Tapering Section) hav = 810 mm

Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 112.31 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 0.00 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 61.52
ULS-Total Moment 269.5 kN-m
Ultimate Limit State Shear Vu = 146 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) INT CHK LVL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 4825.49 2123.80 OK
2 ULS Moment resistance KN-m 269.52 2069.85 OK
3 Crack Width mm 0.000 0.25 OK
4 Stress in Steel Mpa 13.03 375.00 OK
5 Stress in Concrete Mpa 0.50 17.5 OK
6 Area of Shear Reinforcement mm2 392.70 221.6 OK
7 Torsional Shear Stress and Capacity Mpa 0.137 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2010 842.34 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2123.80 mm2
As provided = 4825.49 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1061.9 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 4825.49 + 0 4825.5 mm2
Reinf. steel area provided, Ast (flexure) 4825.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 986.1 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 2070 kN-m

Design of Substructure for Br. No. 395 206 of 218

Br NO 395-R2 RN2
Serviceability Limit State Check STATUS OK
Crack Width Check
Overall Depth of Section h= 1170 mm
Depth of Neutral axis NA, x= 250.32 mm
Distance from to the surface of the nearest longitudinal bar acr = 109.60 mm
Calculated strain in the tension reinforcement es = 0.000119
Strain at cracking LVL- Without stiffening Eff e1 = 0.0001 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.007746
Strain at cracking LVL- With stiffening Eff em = -0.0076 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 3.066E+10 mm4
Crack Width W cr = 0.0000 < 0.25 mm OK Tab-10
Stress in Steel fs = 23.79 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -0.92 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 62 KN-m

Stress in Steel fs = 13.03 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 0.50 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.828
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.543 MPa
vc' = xs vc (2d/av) = 0.450 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v < vc', hence Asv reqd = 221.6 mm2
Asv prov 392.7 mm2
v = Vu / (bd) 0.137 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 48.4 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1169.9 mm
Longer Core Dim of Section y1max = 1059.9 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.137 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2

Design of Substructure for Br. No. 395 207 of 218

Br NO 395-R2 RN2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.03 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 702.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 842.34 mm2
Area of reinforcement Provided = 2010 + 0 2010 mm2

6.2 At Top of Foundation

S.No LOAD L.A. Mom Ultimate Load

DESCRIPTION OF LOAD
. VERT HORZ. (m) ent Fac Hu Vu Mu
1 Active Earth Pressure
Horizontal Component P ah 343.0 3.2 1103.9 1.7 583.1 1877
Vertical Component P av 107.5 0.3 34.6 1.7 182.7 59
2 Earth Pressure due to Surcharge P h 17.7 2.5 43.4 1.7 30.1 74
3 Passive Earth Pressure 26.4 0.5 -12.3 1.7 44.9 -21
4 Self Weight & Back Fill 396.6 1.0 388.9 1.3 495.8 486
TOTAL 504.1 1558.5 658.2 678.5 2474
Due to seismic Effect -35.5 212.1 926.4 1.6 339.4 56.9 1482
Combined Load with Seismic 468.6 2484.9 997.6 735.4 3957

6.2.1 Stresses at Top of Foundation

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2) Permissible

Load ent (KN/m2)
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B) Comp Tension
Without Seismic504.1 1558.5 3.1 1.9 1343.2 -902.9 #REF! #REF!
2.3
With Seismic 468.6 2484.9 5.3 4.2 2434.3 -2025.1 #REF!

Checking at Section AT TOP of FND

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm

Design of Substructure for Br. No. 395 208 of 218

Br NO 395-R2 RN2

dia of link 10 mm
long. Spacing (max= 1636 mm) 200 mm
No. of legs 5 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 2290 mm
Average Overall depth of the section ( In Tapering Section) hav = 1145 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 466.91 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 43.38 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 926.41
ULS-Total Moment 3956.7 kN-m
Ultimate Limit State Shear Vu = 998 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.25 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) AT TOP of FND

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 4825.49 4363.60 OK
2 ULS Moment resistance KN-m 3956.71 4350.80 OK
3 Crack Width mm 0.000 0.25 OK
4 Stress in Steel Mpa 93.32 375.00 OK
5 Stress in Concrete Mpa 2.41 17.5 OK
6 Area of Shear Reinforcement mm2 392.70 309.2 OK
7 Torsional Shear Stress and Capacity Mpa 0.457 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 4.03 0.40 OK
9 Secondary Reinforcement mm2 2010 1244.28 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 4363.60 mm2
As provided = 4825.49 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Design of Substructure for Br. No. 395 209 of 218

Br NO 395-R2 RN2

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 2181.8 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 6.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 4825.49 + 0 4825.5 mm2
Reinf. steel area provided, Ast (flexure) 4825.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 2072.7 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4351 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 2290 mm
Depth of Neutral axis NA, x= 373.64 mm
Distance from to the surface of the nearest longitudinal bar acr = 109.60 mm
Calculated strain in the tension reinforcement es = 0.000257
Strain at cracking LVL- Without stiffening Eff e1 = 0.0003 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.006364
Strain at cracking LVL- With stiffening Eff em = -0.0061 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 1.436E+11 mm4
Crack Width W cr = 0.0000 < 0.25 mm OK Tab-10
Stress in Steel fs = 51.40 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -1.33 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 926 KN-m

Stress in Steel fs = 93.32 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 2.41 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.700
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.427 MPa
vc' = xs vc (2d/av) = 0.299 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 309.2 mm2
Asv prov 392.7 mm2
v = Vu / (bd) 0.457 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 309.2 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 2289.8 mm

Design of Substructure for Br. No. 395 210 of 218

Br NO 395-R2 RN2

Longer Core Dim of Section y1max = 2179.8 mm

Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.457 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 200.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 4.03 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 1036.9 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 1244.28 mm2
Area of reinforcement Provided = 2010 + 0 2010 mm2

6.3 At Bottom of Foundation

S.No LOAD L.A. MomMoment (KN-m)

DESCRIPTION OF LOAD
. VERT HORZ. (m) ent Front L.A. Ms
1 Active Earth Pressure
Horizontal Component P ah 644.8 4.4 2844.8
Vertical Component P av 202.0 0.4 89.1 9.4 1908.7
2 Earth Pressure due to Surcharge P h 65.9 5.3 345.9
3 Passive Earth Pressure 121.3 1.0 -121.3
4 Self Weight & Back Fill 1721.1 3.5 5945.9 6.4 ######
TOTAL 1923.1 589.3 9104.3 ######
Due to seismic Effect -144.0 2760.7
Combined Load with Seismic 1779.1 11865 ######

6.2.1 Stresses at Bottom of Foundation

Vert. Mom Z (m) e (m) Pmax (KN/m2)Pmin (KN/m2) Permissible

Load ent (KN/m2)
Case (t) (KN- B (m)
m)
W M M/W Z-B/2 W/B(1+6e/B) W/B(1-6e/B) Max Min
Without Seismic
1923.1 9104.3 4.734 0.211 219.31 169.59 470.0 0.0
9.890
With Seismic 1779.1 11865 6.669 1.724 368.07 -8.29 626.7 0.0

Maximum Eccentricity, e = 1.724 m (Eccentricity outside middle

Effective width of foundation after redistribution of pressure
9.89(B'=B-2e)
- 1.72 - = = 6.441 m
Maximum Pressure after redistribution = 276 x 9.9 x 6.441 = 423.8 KN/m2

Design of Substructure for Br. No. 395 211 of 218

Br NO 395-R2 RN2

Design of Toe Slab

Max Projection of Toe Slab = 3.600 m

On safer side Taking Max Foundation Pressure as UDL ( Though it will be Trapezoidal )

Max Pressure = 368.070 kN/m ( Taking Unit Width in Consideration )

2
368.070 x 3.600 =
Max Moment = 2385.09
2

Ultimate Moment 1.500

= x 2385.09 = 3577.64 kN-m

Ultimate Shear, Hu = 368.1 x 2.000 x 1.5 = 1104 kN

Checking at Section TOE

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 1119 mm) 200 mm
No. of legs 7 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm
Average Overall depth of the section ( In Tapering Section) hav = 800 mm
Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 1590 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 530 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 2120
ULS-Total Moment 3578 kN-m

Design of Substructure for Br. No. 395 212 of 218

Br NO 395-R2 RN2

Ultimate Limit State Shear Vu = 1104 kN

Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) TOE

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 8042.48 2984.00 OK
2 ULS Moment resistance KN-m 3577.64 4777.59 OK
3 Crack Width mm 0.116 0.20 OK
4 Stress in Steel Mpa 193.00 375.00 OK
5 Stress in Concrete Mpa 8.20 17.5 OK
6 Area of Shear Reinforcement mm2 549.78 389.2 OK
7 Torsional Shear Stress and Capacity Mpa 0.740 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1005 830.4 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2984.00 mm2
As provided = 8042.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1492.0 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1365.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4778 kN-m

Serviceability Limit State Check STATUS OK

Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 378.53 mm
Distance from to the surface of the nearest longitudinal bar acr = 74.97 mm
Calculated strain in the tension reinforcement es = 0.000965
Strain at cracking LVL- Without stiffening Eff e1 = 0.0011 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000522
Strain at cracking LVL- With stiffening Eff em = 0.0005 (Eq.25)

Design of Substructure for Br. No. 395 213 of 218

Br NO 395-R2 RN2
Modular Ratio- Long Term n= 8.00 5.2.6
4
Moment of Inertia I 9.785E+10 mm
Crack Width W cr = 0.1159 < 0.2 mm OK Tab-10
Stress in Steel fs = 193.00 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -8.20 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 2120 KN-m

Stress in Steel fs = 193.00 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 8.20 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.761
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.575 MPa
vc' = xs vc (2d/av) = 0.438 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 389.2 mm2
Asv prov 549.8 mm2
v = Vu / (bd) 0.740 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 389.2 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1490.0 mm
Torsional Stress vt = 2Tu / [h2min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.740 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 692.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 830.4 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

Design of Substructure for Br. No. 395 214 of 218

Br NO 395-R2 RN2

Design of Heel Slab

Max Projection of Toe Slab = 4.000 m

Total Weight of Soil / m Run = ##### x 18.00 = 226.908 kN/m

Surcharge = 17.703 kN/m

Total Vertical UDL =226.9 + 17.70 = 244.611 kN/m

Vertical UDL 244.611 kN/m ( Taking Unit Width in Consideration )

2
244.611 x 4.000 = 1956.89
Max Moment =
2

Ultimate Moment 1.700

= x 1956.89 = 3326.7 kN-m

Shear = 244.611 x 4.000 = 978.4 KN

Ultimate Shear = 1.500 x 978.45 = 1467.7 kN-m

Mu = 3326.7 kN-m

Checking at Section HEEL

Type of Design SLAB

Materials Property

Specified minimum comp. strength of conc. at 28 days fck = 35 MPa

Specified minimum yield strength of main reinf. Steel fy = 500 MPa
Specified minimum yield strength of sec. reinf. Steel fyv = 500 MPa
Elastic modulus of reinf. Steel Es = 200000 MPa 4.6.2.1
Elastic modulus of concrete Ec = 29500 MPa Table3

Reinforcement Data

Reinf. diam. in first layer dbm = 32 mm

Spacing in first layer 100 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c
Dia of spacer bar 0 mm
dia of link 10 mm
long. Spacing (max= 1119 mm) 200 mm
No. of legs 8 nos
Reinf. diam. in first layer dbm = 16 mm
Spacing in first layer 200 mm c/c
Reinf. diam. in second layer dbm = 0 mm
Spacing in second layer 0 mm c/c

Section Dimension

Overall width of the section b= 1000 mm

Overall depth of the section h= 1600 mm

Design of Substructure for Br. No. 395 215 of 218

Br NO 395-R2 RN2

Average Overall depth of the section ( In Tapering Section) hav = 800 mm

Clear cover to Ast Cc = 50 mm

Moment , Shear and Torsion

SLS Moment- Permanent ( For Crack Width - Comb-1- Cl 11.3.2) 1305 kN-m
SLS Moment- Live Load ( For Crack Width - Comb-1- Cl 11.3.2) 435 kN-m
Max SLS Moment ( For Stress Chk - Comb-1 to 5- Cl 11.3.2) 1739
ULS-Total Moment 3327 kN-m
Ultimate Limit State Shear Vu = 1468 kN
Ultimate Limit State Torsion, Tu 0.0 kN-m

Other Inputs

Allowable crack width 0.2 mm

required nominal cover to the tensile reinforcement cnom = 50 mm
Width for Enhance Shear av = 0 mm 15.4.3.3

Summary of Output ( Detail Calculation Given below) HEEL

Sr No Item Unit Actual Permissible Result

1 Minimum Reinforcement mm2 8042.48 2984.00 OK
2 ULS Moment resistance KN-m 3326.71 4777.59 OK
3 Crack Width mm 0.050 0.20 OK
4 Stress in Steel Mpa 158.35 375.00 OK
5 Stress in Concrete Mpa 6.73 17.5 OK
6 Area of Shear Reinforcement mm2 628.32 524.1 OK
7 Torsional Shear Stress and Capacity Mpa 0.984 4.43 OK
8 Longitudinal Reinforcement due to Torsion mm2/mm 8.05 0.40 OK
9 Secondary Reinforcement mm2 1005 830.4 OK

DESIGN FOR FLEXURE

ec fc
X
N a' A
h

cc
es
e1 fs
STRAIN STRESS b

Minimum Reinf. Reqt. Check STATUS OK

As min = 0.2 % (bd) 2984.00 mm2
As provided = 8042.48 mm2
0.2% of (bd) if fy>415MPa, 0.35% of (bd) if fy=250MPa

Ultimate Limit State Check STATUS OK

Eff. depth of the section 'd' for single layer d= 1492.0 mm
CG of reinforcements, dc 76.0 mm
Number of reinforcing bars, Nb 10.0
Number of reinforcing bars, Nb 0
Reinf. steel area provided, As = 8042.48 + 0 8042.5 mm2
Reinf. steel area provided, Ast (flexure) 8042.5 mm2
z = Min[0.95,(1-1.1*fy*Ast / (fcu*b*d) ) ]*d 1365.6 mm
Flexural resistance, Mr = Min(0.87*fy*Ast*z , 0.15*fcu*b*d^2)/1E6 > Mu, OK 4778 kN-m

Design of Substructure for Br. No. 395 216 of 218

Br NO 395-R2 RN2
Serviceability Limit State Check STATUS OK
Crack Width Check
Overall Depth of Section h= 1600 mm
Depth of Neutral axis NA, x= 378.53 mm
Distance from to the surface of the nearest longitudinal bar acr = 74.97 mm
Calculated strain in the tension reinforcement es = 0.000792
Strain at cracking LVL- Without stiffening Eff e1 = 0.0009 @cnom
Strain at cracking LVL- With stiffening Eff ets = 0.000637
Strain at cracking LVL- With stiffening Eff em = 0.0002 (Eq.25)
Modular Ratio- Long Term n= 8.00 5.2.6
Moment of Inertia I 9.785E+10 mm4
Crack Width W cr = 0.0501 < 0.2 mm OK Tab-10
Stress in Steel fs = 158.35 < (0.75fy) 375 MPa OK Tab-11
Stress in Concrete fc = -6.73 < (0.5fc) -17.5 MPa OK Tab-11

Stress Check- SLS Condition STATUS OK

Maximum SLS Moment m 1739 KN-m

Stress in Steel fs = 158.35 Mpa
Permissible Stress in Steel 0.75fy = 375 OK Tab-11
Stress in Concrete fs = 6.73 Mpa
Permissible Stress in Concrete 0.5fck = 17.5 OK Tab-11

DESIGN FOR SHEAR

Nominal Shear Resistance and Capacity STATUS OK

2d / av = 1
depth factor, xs = 0.761
vc = 0.216*(pt)1/3*min(fc,40)1/3 0.575 MPa
vc' = xs vc (2d/av) = 0.438 MPa
if v < vc', Asv = 0.4bsv/0.87fyv 221.6 mm2
v > vc', hence Asv reqd = 524.1 mm2
Asv prov 628.3 mm2
v = Vu / (bd) 0.984 MPa
if v > vc', Asv = (v-vc'+0.4)bsv/0.87fyv 524.1 mm2
if v < v c ', no min shear rft is reqd in case of slabs but reqd in beams.

DESIGN FOR TORSION

Torsional Shear Stress and Capacity STATUS OK

Smaller Outer Dim of Section hmin = 1000.0 mm
Smaller Core Dim of Section x1min = 890.0 mm
Longer Outer Dim of Section hmax = 1600.0 mm
Longer Core Dim of Section y1max = 1490.0 mm
2
Torsional Stress vt = 2Tu / [h min ( hmax - ( hmin/3) ) ] = 0.0000 MPa 15.4.4.4
Ultimate Torsion Shear Stress vt min = 0.38 MPa Tab-17
Check if Torsional Reinf reqd > vt Torsion Rft is not Required
v + vt = 0.984 MPa < 4.43 MPa Torsional Capacity is OK
Torsional Reinforcement Asv ≥ [Tusv/(1.6x1y1(0.87fyv))] = 0 mm2

Longitudinal Reinforcement due to Torsion STATUS OK

Area of main reinforcement ( Outer Layer) AsL = 804.2 mm2
Spacing of Main reinforcement ( Outer Layer) sL = 100.0 mm2
Area of Shear reinforcement ( Outer Layer) Asv = 78.5 mm2
Spacing of Shear reinforcement ( Outer Layer) sv = 200.0 mm2

Design of Substructure for Br. No. 395 217 of 218

Br NO 395-R2 RN2
[AsL / sL] ≥ [Asv*(fyv / fy) / sv ] 8.05 > 0.4 OK
Longitudinal Reinforcement provided is OK

Secondary Steel on Compression face STATUS OK

Eff. depth of the section 'd' for single layer d= 692.0 mm
Width of Section b= 1000.0 mm
Area of Secondary reinforcement require - on either side @ 0.12 % 830.4 mm2
Area of reinforcement Provided = 1005 + 0 1005 mm2

7 STABILITY CALCULATION
7.1 Against Overturning (Sub Structure Code Clause 5.10.1.1 and 6.8 )

Mo = Moment due to [E.P. (Horz. Component) + Surcharge (Horz. Component)]

Without seismic,
Mo = 2844.8 + 345.9 = 3190.6 KN-m
With seismic, Mo = 2844.8 + 345.9 + 2760.7 = 5951.35 KN-m

Ms = Moment due to [E.P. (Vert. Component) + Surcharge (Vert. Component)] +

Moment due to self Wt. & Earth Fill
Without seismic,
Ms = 12984.09 KN-m (Calculated in Table 6.3 )
With seismic, Ms = 12984.09 KN-m (Calculated in Table 6.3 )

DescriptionRestoring moment (M
Overturning
s Factor of Safety (Ms/M FOS (Reqd.)
moment (M
Without Seismic 12984.091 3190.629 4.07 2.0
With Seismic 12984.091 5951.346 2.18 1.5

7.2 Against Sliding (Sub Structure Code Clause 6.8 )

Total Horz. Force, H = 644.75 + 65.87 = 710.62 KN

Total Vert. Force, W = 1923.100 KN

Coff of Friction, m = 0.50

Base Width = 9.89 m
Cohesion, c = 10.00 KN/m2
Passive Force, P p = 121.34 KN (Ref. 9.2 )
Total Resisting Force, R = m W+Bc+P p
961.550 + 98.898 + 121.340

= 1181.789 KN

Factor of Safety = Resisting Force 1181.8

= = 1.663 >1.5 SAFE
Horz. Force 710.6

Design of Substructure for Br. No. 395 218 of 218