Scribd
Upload
138 views2 pages

Solvent Base Vs Hydro Stains

The conventional staining process involves spraying stain onto wood and wiping off the excess, allowing it to dry slowly. This wiping stain method requires less training but produces uneven results on some wood types like maple and requires pre-treatment. It also takes longer than spray-only stains, has toxic fumes, and can bleed and leave marks. The document recommends using an in-house lab to match stains made from European water-based or "Hydro" stain technology. Hydro stains can produce uniform results more quickly and with lower VOC emissions than solvent-based wiping stains. However, they may not replicate some effects achieved with wiping stains on open-pore woods like oak.

Uploaded by

Ehtesham Sazzad
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views2 pages

Solvent Base Vs Hydro Stains

The conventional staining process involves spraying stain onto wood and wiping off the excess, allowing it to dry slowly. This wiping stain method requires less training but produces uneven results on some wood types like maple and requires pre-treatment. It also takes longer than spray-only stains, has toxic fumes, and can bleed and leave marks. The document recommends using an in-house lab to match stains made from European water-based or "Hydro" stain technology. Hydro stains can produce uniform results more quickly and with lower VOC emissions than solvent-based wiping stains. However, they may not replicate some effects achieved with wiping stains on open-pore woods like oak.

Uploaded by

Ehtesham Sazzad
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

The conventional staining process.

Conventional application of stain is generally applied by a spray and wipe process using solvent base stains. The stain is sprayed on, wiped off, and then must dry. As a wiping stain, it must be formulated to dry slowly, or what is known as an open time, to enable time to wipe the stain evenly. ADVANTAGES: Wiping stains require relatively little training. Heavier pigments in these stains enhance the grain in open pore woods such as oak and hickory, producing a strong grain strike. DISADVANTAGES: Wiping stains on woods such as beech, maple and birch usually require a pretreatment to reduce blotchy results; this step adds additional labor and material V.O.C.s. From solid woods to veneers, uniformity of color is not always even. Application of a wiping stain takes 3 4 times longer than spray only stains. Dry times may vary from 45 minutes to several hours. Deep colors usually require an additional color step such as a spray only prestain. Solvent base wiping stains are the single highest exposure of bodily contact to toxic fumes. Fumes are absorbed not only through the lungs, but also through eye membrane and the skin. Bleed back of stain from pores and crevices between frames and panels is a common occurrence requiring the additional labor for re-wetting and removal. Solvent base stains are toxic. They are some of the highest in V.O.C.s of all finishing products. Wiping stains must be removed by hand; rag marks and hand prints are inevitable, costing time and money to repair. Solvent base stains are not considered green. Solvent base wiping stain rags produce waste. Used rags are flammable and a common reason for shop fires. Rags leave behind cotton fibers in the wood, which must be sanded out of the finish. Used rags must be dried and disposed of carefully. Much of the wiping stain is wasted. As much stain is left in the rags as is on the wood.

INDUSTRIAL COATINGS SOLUTIONS offers many advantages to staining.

We recommend setting up an in-house lab to make all stain matches. None of the products offered here will require any specialized equipment.

European water base stain technology or Hydro stains.


ADVANTAGES Factoring in a spray application, and in-house color matching, staining cost in labor and material may be lowered by 30% or more. Make only the amount of stain you need, further cutting costs by minimizing waste.
Making the stain when you need it, on time, no longer relying and waiting on an outside supplier. Many existing colors can be matched with the Hydro stains. For Beech and Maples, European Hydro stain technology is considerably more uniform than any wiping stain. In many cases, deep colors are achieved in one step rather than two. Dry times of Hydro stains are twice as fast as the fastest wiping stain. Hydro stains are green. V.O.C.s from staining would be virtually eliminated. Hydro stains achieve maximum uniformity on difficult to stain woods such as Beech and Maple. Pre-treatment of these woods would be eliminated. Because wood is made with water, Hydro stains have a natural relationship with wood, therefore are the most user friendly of spray stain applications. Hydro stains are compatible with most finishes.

DISADVANTAGES Not all stain effects can be replaced with the Hydro stains. Open pore woods such as oak and hickory achieve maximum grain strike with wiping stains. NOTE: Optional specialty colors may be offered with the use of Hydro stains as a pre-stain under solvent wiping stain. This achieves the deepest of colors with clarity, uniformity and definition.

You might also like