Installation Procedure

iR5075/5065/5055 Series

Apr 24 2007
Chapter 1 Installation
Procedure
 Chapter 1　

1.1 Making Pre-Checks

1.1.1 Selecting the installation space 0015-4647

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

The conditions of the installation space include the following.

Preliminary inspection of the planned installation space would be desired before shipping the machine to the custom-
er.
1. The power supply can be connected to a power outlet of 100 V -/+ 10 V, 15 A or more. The host machine can be
grounded.
Grounding target
1) Grounding terminal of power outlet
2) Grounding terminal finished to category D
2. The temperature and humidity are within the range shown in the following figure. The area near the faucet, water
heater, moisture chamber and refrigerator should be especially avoided.

(%RH)
100

[C]
90
85
[B]
75
70 [A]

50

25
20
15
10
5

0 10 15 20 25 30 35 40 (degC)
7.5 23 27.5 32.5
F-1-1

<Assured environmental zone>

[A]: A zone. All quality standard items are satisfied.
[B]: B zone. Some quality standard items are inferior to those in A zone or not satisfied.
[C]: C zone. Copying operation is performed normally without any safety issues, malfunction, and errors in display.

2
 Chapter 1

3. The area near the origin of fire, with full of dust and where ammonia gas generates should be avoided. In the case
that the space is exposed to direct light, it is better to hang a curtain on the window.
4. Although the ozone level generating in using this equipment does not affect human bodies, long-hours operation
in a poorly-ventilated room may cause some odor to be sensed. Ventilation should be done to keep a comfortable
work environment.
5. The foot of the host machine should not get off the floor. The host machine should be kept in a horizontal status.
6. The host machine should be separated from the wall by 100 mm or more to keep a space sufficient for machine
operation.
- When installing the Copy Tray-L1

100 mm or more

13,74 mm
1,278 mm
500mm 1,448 mm 500mm

500mm

F-1-2

- When installing the Saddle Finisher-AD2 + Paper Folding Unit-E1 + Document Insertion Unit-E1 + Puncher Unit-
AS1 + Paper Deck-AE1

100 mm or more
1,278 mm

1,374 mm

2,482 mm
500mm 109 mm 2,591 mm 500mm

500mm

F-1-3

7. This equipment should be installed in a well-ventilated room, however not near the ventilating suction mouth in
the room.
8. In the case that several machines are installed at the same area, this machine should be arranged so that this ma-
chine does not draw directly the exhaust air from the other machines. The life of the charging wire may be short-
ened, especially in a low-humidity environment.

3
 Chapter 1　

F-1-4

1.1.2 Combination Table of Accessories 0015-7973

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

The following table shows the combination of accessories that are set at the right side of the host machine.
When setting the accessories indicated in the table, refer to the table below and check the combination before
the setup.

T-1-1

Document Voice Guidance Kit Card Reader

Tray

Document Tray - no yes

Voice Guidance Kit no - yes

Card Reader yes yes -

yes: Available no: Unavailable

4
 Chapter 1

1.1.3 Checking the Contents 0016-8935

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

[1] [2] [3] [4] [5]

[6] [7] [8] [9] [10] [11] [12] [13]

[14] [15] [16] [17] [18] [19]

FU5-8564

1 2 3 4 1 2 3 4
A3 B4 12 18
A3 B4 11 17
A4 B5 11 17
81 2 14
A4
A3
B5
B4
A5
A4 R
B5 R A5 R A4 B5 LEGAL
81 2 14
A4 LTR
A3 11x17
STMT
LGL
LTR R
A5
A4 R
A5 R
STMT R
A4 B5 LEGAL
A4
A3
A5
A4 R
A5 R
A5 EXEC
81 2 11
LTR
TR
81 2 11
A4 LTR/11x17 STMT
A3 16K B5 LGL
8K B4 LTR R
A5
A4 R
A5 R
STMT R 8K FLSC LTR
TR
81 2 11
16K FOLIO LTR
TR
51 2 81 2
305 457mm OFICIO STMT

[20] [21] [22] [23] [24] [25] [26] [27]

F-1-5

[1] Developing assembly 1pc. [2] Developing assembly pressure unit 1pc.

[3] Service book case 1pc. [4] Latch face cover 1pc.

[5] Grip cover (small) 1pc. [6] Grip 1pc.

[7] Grip cover (large) 3pc. [8] Drum rotation tool 1pc.

[9] Deck pressure plate 1pc. [10] Inch-series block 4pc.

5
 Chapter 1　

[11] Base sheet 1pc. [12] One-touch supports 2pc.

[13] Index paper attachment 1pc. [14] Power cable 1pc.

[15] ADF communication cable 1pc. [16] Reader communication cable 1pc.

[17] Paper size plate 2pc. [18] Touch pen 1pc.

[19] Wire saddle 1pc. [20] Screw (RS tightening; M4X8) 1pc.

[21] Screw (binding; M4X6) 1pc. [22]* Glass cleaning paper 1pc.

[23] Shutdown label 2pc. [24] Document size label 1pc.

[25] Paper size label 1pc. [26] Cleaning procedure label 1pc.

[27] Cleaning position label 1pc.

* Not used upon installation

Check the contents (advice book, CD, and others) against the following tables:

iR5075N
Documentation iR5065N iR5065
iR5055N iR5055

User's Guide yes yes

License agreement for software yes yes

Send Trial Kit yes yes

Release Notes yes no

Network Quick Start Guide yes no

iR5075N
iR5065
CD-ROM iR5065N
iR5055
iR5055N

Tutorial CD yes yes

ManualCD yes yes

MEAP Admin. CD-ROM yes yes

UFR II/PCL Driver/Utility CD-ROM yes no

iW MC CD-ROM yes no

Printer Guide CD-ROM yes no

6
Chapter 1

7
 Chapter 1　

1.2 Unpacking and Instal- 1.2.2 Unpacking 0015-4654

lation iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1.2.1 Unpacking and

1) Unpack the package, and remove the vinyl.
installation procedure 0015-4653 2) Open the attached cardboard box, and then insert
the 1 grip [1] that has been included to the front of
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
the pickup side.
iR5055N

Take into account the following points when install-

ing this equipment.
[1]

1. When transferring the host machine from a low-

temperature to a warm place and installing it, dew
condensation may occur around the pickup/feed as-
sembly, leading to image faulty reproduction.
Therefore, the host machine is unpacked and left
for 1 hour or more to make it accustom to room
temperature (Dew condensation: The phenomenon
where water drops accumulate on the surface of
metal when a metal material is moved from a low-
temperature to a warm area and the moisture in the
air surrounding the metal is quickly cooled)

2. When using stairways for carrying in and out from/to

the installation space, take into account the following
points. F-1-6

1) When lifting the host machine, do not use the left

and right grips (3 locations) but hold the four cor-
ners at the bottom of the host machine.
2) The mass of this equipment is approx. 230 kg.
Be sure to insert the leaf spring of the grip down-
Make sure that four persons perform unpacking.
ward. Adverse insertion may cause the grip com-
3) Remove the ADF assembly, the fixing feed unit
ing off while lifting the host machine.
assembly and the duplexing unit assembly, and
then separate them from the host machine before
carrying in and out.
3) Hold the 2 grips (front/rear) on the pickup assembly
side [1] of the host machine, and then remove the 2

8
 Chapter 1

pads [2] while lifting the host machine a little.

(Mass of the host machine: Approx. 230 kg)

If the slope plate is difficult to remove, displace-

ment of the host machine to the rear edge of the
skid makes operation easier.

6) Reverse the slope plate [1]. Match the pin hole of

the skid against the pin hole of the slope plate, and
[1]
then insert the 2 pins [2].

[2]
F-1-7
[2]

4) Hold the 2 grips (front/rear) on the delivery assem-

bly side [1] of the host machine, and then remove
the 2 pads [2] and the vinyl bag while lifting the
host machine a little.
[1]

[1]

F-1-9

7) Hold the grip [1] of the host machine. Slide the host
machine on the slope to get it down from the skid.

Be careful that the caster [2] does not fall out from
the skid.

[2]
F-1-8 [2]

5) Remove the cardboard on the skid, and then take

out the 2 slope plates installed at the center of the
skid.

9
 Chapter 1　

9) Remove the packing tape attached onto the host

machine.

1.2.3 Installation of Scan-

ner 0015-4657
[1] iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N

1) Open the DADF, and remove the packing materi-

als.
2) Remove the scanner fixing screw [1].

[1]

[1]

F-1-10 F-1-12

8) Remove the grip [1] while pressing the leaf spring

with a flathead screwdriver.

The scanner fixing screw will be used when relo-

cating the machine; thus, make sure a user stores
away it.

3) Pull the release lever [1] and open the white sheet
[1] [2] in the direction of the arrow [A].

[2] [1]

[A]

F-1-13

F-1-11
4) Remove the protection sheet.

10
 Chapter 1

3) Remove the separation claw release member [1]

[1] and tag [2] attached onto the fixing/feeder assem-
bly.

Make sure to remove the foreign particles, such as

tape glue, from the surface of the feeder belt.

F-1-14

T-1-2

After the host machine is installed, if moving the

machine elsewhere, put the protection sheet.
If not, the image may be affected.

5) Close the white sheet.

6) Close the DADF.

1.2.4 Installation of Fixing

Assembly 0015-4659
[2] [1]

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / F-1-16

iR5055N
4) Peel off the tag tape to open the fixing/delivery as-
1) Open the front cover. sembly [1].
2) Shift the fixing/feeder assembly release lever [1] in
the direction of the arrow, and release the transfer/ [1]

separation charging assembly. Slide the fixing/

feeder unit [2] out toward the front.

F-1-17

5) Remove the 2 fixing nip pressure release screws

[1] [2] [1].
F-1-15

11
 Chapter 1　

[1] [3]

[1]

[2] [1]
F-1-20

3) While holding the front and rear sides of the trans-

F-1-18 fer/separation charging assembly [1], slide it in the
[A] direction; then, remove it toward the [B] direc-
6) Close the fixing/delivery assembly. tion.

1.2.5 Checking of Charg-

ing Assembly and
Be careful not to cut the nylon wire by contacting
Dustproof Glass 0015-4660 the transfer/separation charging assembly with the
transfer guide.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N

1) Detach the feeder assembly front cover (right) [1].

- 2 screws [2]

[2]
[B]

[A]

[1]
F-1-21
[1]

4) Check the transfer/separation charging assembly. If

[2] any dirt or paper powder is attached onto the assem-
F-1-19 bly, clean it with alcohol solutions.
5) Mount the transfer/separation assembly using the
2) Remove the screw [1] and the mount [2], and dis- steps to remove it but in reverse.
connect the connector [3]. 6) Attach the feeder assembly front cover (right) with

12
 Chapter 1

the 2 screws (use the screws removed in the step 1).

Put back the fixing/feeder assembly and the duplex-
[2]
ing unit to the original positions (leave the fixing/
feeder assembly release lever as it is).
7) Open the toner replacement cover.
8) Detach the toner replacement cover [1].
- 2 screws [2]

[2] [2]

[3] [1]
F-1-24

[1]
11) Loosen the screw [1] and shift the charging assem-
F-1-22 bly mount [2] in the direction of the arrow; then,
tighten the screw once again.
9) Detach the connector cover [1]. 12) Disconnect the connector [3], and remove the
- 1 screw [2] primary charging assembly [4].

[1] [2]

F-1-23 [3] [4] [1] [2]

F-1-25
10) Remove the 2 screws [1] and disconnect the con-
nector [2]; then, remove the primary fan duct [3]. 13) Check the primary charging assembly. If any dirt
or paper powder is attached onto the assembly,
clean it with alcohol solutions.
14) Disconnect the connector [1] and remove the
screw [2]; then, slide the pre-transfer charging as-
sembly [3] out.

13
 Chapter 1　

3. Make sure that the one-way arm of the pre-transfer

charging assembly is placed onto the eccentric cam.

19) Attach the primary fan duct and the toner replace-
ment cover using the steps to remove them but in
reverse.

[2] [3] [1]

F-1-26
Be sure to connect the connector when attaching
15) Check the pre-transfer charging assembly. If any the primary fan duct.
dirt or paper powder is attached onto the assembly,
clean it with alcohol solutions. 20) Lock the fixing/feeder assembly release lever, and
16) Remove the dustproof glass [1]. close the front cover.

[1]
1.2.6 Installation of
Developing Assembly 0015-4661

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Open the upper right cover [1], and remove the

screw [2] from the door tape; then, open the cover
F-1-27 further.

17) Check and clean the dustproof glass with a blower

Do not make the screws fall off.
brush.
18) Mount the primary charging assembly, the pre-
T-1-3
transfer charging assembly, and the dustproof
glass; then, fix them using the steps to remove them
but in reverse. Do not make the screws fall off.

1. In case of using solutions for cleaning, be sure

that the solutions are completely dried out.

2. When inserting the pre-transfer charging assembly,

slide it in horizontally against the process unit for not to
scratch the surface of the drum.

14
 Chapter 1

[2] [1]

When mounting the developing assembly, be sure

not to contact the developing cylinder with the de-
veloping assembly mounting plate.

[1]

F-1-28

2) Remove the tape [1], and detach the hopper supply

mouth cover [2].

[1]

[2]
[2]

F-1-30

6) Fit the developing assembly pressure unit [1] to [2],

and slide it in horizontally in the [A] direction; then,
shift toward the [B] direction.
- 1 screw (binding; M4X6) [2]

F-1-29
[B] [2]
3) Take out the developing assembly from the packing
box. [A]

4) Rotate the developing cylinder gear with hand, and

[3] [1]
check for scratch on the surface of the cylinder.
F-1-31
5) Mount the developing assembly [1] by holding the
center (pocket for grip) of it.
Then, connect the connector [2]. 1.2.7 Installation of
Pickup Assembly 0015-4662

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Remove the pickup roller pressure release spacer

[1].

15
 Chapter 1　

Remove the pickup roller pressure release spacer

[1] while moving the front side of it upward after
sliding the spacer toward the right.

[1]

F-1-33

3) After removing all spacers, slide the deck/cassette

in and close the lower right cover.
4) Attach the door tape of the upper right cover with
the screw, and close the upper right cover.
[1]

1.2.8 Attaching Deck

Pressure Plate 0015-4663

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Press the release button of the left deck and slide the
left deck out.
2) Attach the deck pressure plate [1] with the screw
[1]
(RS tightening; M4X8) [2].
F-1-32
[1] [2]
2) Slide the right deck and Cassett3/4 halfway out, and
open the lower right cover. Then, remove the pick-
up roller pressure release spacers [1].

MEMO;
The spacers are being pressured while the deck/cassette
is set; thus, it is hard to remove them.
F-1-34
Therefore, release the pressure by sliding the deck/cas-
sette halfway out.
3) Close the left deck.

1.2.9 Setting Toner Con-

tainer 0015-4664

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

16
 Chapter 1

iR5055N 4) Hold the toner container with its mouth [1] at the
right side, and set it into the supply case [2] of the
host machine horizontally.

[2]

Do not shake the toner container.

If setting the toner container that has been shaken to
the host machine, the toner overflow within the ma-
chine may occur.
By shaking the container, the toner fluidity increas-
es. As a result, toner is supplied swiftly to the ma-
chine with the toner supply operation, causing the
foregoing symptoms. [1]
F-1-37

1) Take out the toner container from the packing box. 5) Slide the lock lever [1] upward to lock the toner
2) After opening the toner replacement cover [1], container [2] in place.
pull down the lock lever [2] in the direction of the
[1]
arrow.

[2]
F-1-38
[1] [2]
F-1-35 6) Close the toner replacement cover.

3) Hold the toner container [1] as shown in the figure

below, and remove the cap [2] from the container
by rotating the cap in the direction of the arrow.
When turning on the main power switch without
setting toner container, the toner level meter on the
[2]
control panel shows 25 % or less. Make sure that the
toner container is set in the host machine before
turning on the main power switch.

[1]

F-1-36

17
 Chapter 1　

1.2.10 Connecting the

Cable 0015-4665

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

[1]
iR5055N

1) Attach the wire saddle [1] onto the upper rear cover.

F-1-41

4) Connect the 2 connectors of the ADF communica-

tion cable.

[1]

[1]
F-1-39

2) Connect the 2 connectors [1] of the reader commu-

nication cable, and then fix the cable in place with
the wire saddle [2].

[1] F-1-42

1.2.11 Checking the Envi-

ronment Switch 0015-4667

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Make settings for environment switch [1] and the

[2] cassette heater switch [2] according to the environ-
F-1-40 ment of the installation site. In case the drum/cas-
sette heaters are required to be turned on while the
3) Connect the connector [1] of the ADF power supply main power switch is turned off, make the settings
cable. with the following 2 switches:

Drum heater
ON OFF

18
 Chapter 1

Environment switch ON Environment switch OFF

Main power switch ON Main power switch OFF
[1]

Cassette heater
ON OFF

Cassette heater switch ON Cassette heater switch

Environment switch ON OFF
Main power switch OFF Environment switch ON
[2]
Main power switch ON
F-1-44

<Attaching the cleaning procedure label>

1) Pull the release lever [1] and open the white sheet
[2] in the direction of the arrow [A].

[2] [1]

[A]

[2]
ON

[1]

F-1-45

F-1-43
2) Attach the cleaning procedure labels [1] [2] for the
relevant language.
1.2.12 Attaching the
Label 0015-9830 [1]

iR5065 / iR 5055 / iR5075 / iR5065N / iR5055N

[2]
<Attaching the cleaning position label>
1) Open the DADF [1].
1) Attach the cleaning position label [2] for the rele-
vant language.

F-1-46

3) Remove the reading cleaning tool [1].

19
 Chapter 1　

[1] Be sure to remove the packaging materials inside

the cassette before turning on the main power
switch.

1) In the case of 100V machine, ground the host ma-

chine with the grounding wire.
Targets of Grounding
F-1-47
1. Grounding terminal of power outlet
2. Grounding terminal of which grounding work (D
4) Attach the cleaning procedure label [1] for the rel-
Type) is properly done.
evant language.
2) Slide the duplexing unit out, and check to see that
there is no foreign substances or damage in the unit.
3) Make sure that the main power switch is turned off,
[1]
and then connect the power plug into the power out-
let.
4) Turn on the main power switch.
- The message 'Wait..' appears.
F-1-48

1.2.15 Toner Stirring 0015-4669

5) Put the detached parts back on by reversing the
foregoing steps. iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
- Reading cleaning tool iR5055N
- White sheet
6) Close the DADF. After wait time, execute toner supply in service mode.
1) Enter service mode.
1.2.13 Connecting the 2) Select: COPIER > FUNCTION > INSTALL >
TONER-S.
Power Cord 0015-9944 3) Check the message 'CHECK THE DEVELOPER'
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / appears.
iR5055N 4) Check to see that the developing assembly is at-
tached appropriately, and then press 'OK'.
1) Connect one side of the power cable to the inlet of - It takes approx. 8 to 10 minutes to supply toner.
the host machine, and the other side to the plug out- The machine stops automatically after counting.
let. - Make settings for the cassette until the completion
of toner supply. (See media cassette settings.)

1.2.14 Turning On the

Main Power Switch 0015-4668

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / Be sure not to turn off the machine during its oper-
iR5055N ation.

20
 Chapter 1

5) Press [Reset] to escape from service mode.

1.2.16 Media Cassette

Settings 0015-4671
[1]
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N
[2]

1) Hold down the cassette release button to slide each

cassette to the front. F-1-50
2) Set the side guide [1] of each cassette onto the hole
of the mark M [2] (A4/A3). 4) Close each cassette.

[1] 1.2.17 Index Paper

Attachment 0015-4673

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

[2]
1) Determine the cassette for index paper from either
of Cassette 3 or 4. Press the release button of the
F-1-49 cassette you determined to slide it toward the front.
Fit the 2 one-touch supports [1] onto the holes [2]
3) Attach the inch-series block from inside the cas- of the cassette, and press the pin into the hole to fix
sette onto the hole of the mark A [1] (STMT-R) and them in place.
the hole of the mark H [2] (LTR-R) so that they are 2) Fit the holes of the index paper attachment [3] on
hidden. the one-touch supports [1].
3) Set the base sheet [4] on the cassette.

[1] [3]

-Be sure to attach the inch-series block firmly. [1]

-Go through this procedure only in case of not us- [4]

ing inch-series paper.

[2]

F-1-51

4) Close the cassette.

21
 Chapter 1　

1.2.18 Changing the image.

- Copy operation: Check to see that the copy oper-
Media Size of the Front ation is appropriate.
Deck (Left/Right) 0015-4674
- Duplexing copy operation: Check to see that the
paper feeding at the duplexing unit is appropri-
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / ate.
iR5055N - Pickup operation: Check to see that paper pick-
up from each source of paper is appropriate.
1) Hold down the release button to slide the deck out. - Operation noise: Check to see that there is no
2) Remove the screw [4] of the trailing end plate [1], abnormal sound.
the left guide plate [2], and the right guide plate [3] - Fixed ratio reproduction: Check the image
respectively, and secure each plate in place at the quality for each fixed ratio reproduction.
position of the size that user wishes. - Multiple copies: Check to see that the copy op-
Default setting: A4 size eration for a specified number of sheets is appro-
After setting the size, set the deck into the host ma- priate.
chine. - Check to see that print images picked up from
each cassette/deck are within the scope of speci-
[3] [1]
[2] fications.
[4] Specification for image left end margin: 2.5 -/
+1.5mm
Specification for image leading edge margin: 4.0-
1.5/-1.0mm
In case the values is/are out of the scope of the spec-
ifications, see 'Adjustment of image left end mar-
gin' and 'Adjustment of image leading edge
[4] margin'.
F-1-52
* In case there is a difference in density between the
left and the right of the image, adjust the height of
3) Attach the new media size label onto the media size
the primary charging wire at the rear side to correct
plate of the deck.
it.
4) In case the size is changed, register the front deck
media size in service mode.
Right deck: COPIER > OPTION > CST > P-SZ-C1
Left deck: COPIER > OPTION > CST > P-SZ-C2
A4=6, B5=15, and LTR=18 Due to the drop of toner from the drum separation
claw, there may be a dirty image in the initial 10
1.2.19 Image/Operation sheets. This dirt disappears as copy volume goes
on.
Check in User Mode 0015-4675
2) At customer's desire, set the standard mode from
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
user mode or service mode.
iR5055N
3) Place media in the right/left decks.
4) Close the right/left decks. Tear off the relevant me-
1) Press [Reset] twice and return to the main screen.
dia size label [1] from the mount sheet, and then at-
Using test sheet, check the copy operation and copy

22
 Chapter 1

tach it onto the media size plate of the deck. cassette.

[1]

[1]

F-1-53 F-1-55

5) Hold down the release button, and then slide 3) Adjust the position of the cassette body [1] by shift-
Cassette3 and 4 out. ing it to the front or the rear.
6) Tear off the relevant media size label [1] from the Shift to the rear = Decreases the left end margin
mount sheet, and attach it onto the media size plate Shift to the front = Increases the left end margin
[2] of the cassette. Set the media size plate in the
cassette.

[1] [2]
[1]

[1]

F-1-54

7) Close each cassette.

1.2.20 Adjustment of
Image Left End Margin 0015-4676
F-1-56
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N 4) Check that the left margin of the copied image from
Cassette 3/4 is as follows : L1=2.5-/+1.5mm
<Cassette 3/4>
1) Hold down the cassette release button, and then
slide Cassette 3 and 4 out.
2) Loosen the 2 fixing screws [1] at the left/right of the

23
 Chapter 1　

[3] [2]

image
[1]
L1

F-1-57
[2]
[1]
[1] Feeding direction of paper
F-1-58
5) Tighten the 2 screws loosened at the step 2)
6) Close Cassette 3/4
3) Move the cassette guide assembly [1] toward either
7) After the adjustment, perform the following in ser-
the front or the back and perform adjustment.
vice mode:
Move the guide plate toward the back = the left
Cassette 3
margin is reduced
COPIER> FUNCTION> CST> C3-STMTR/A4R
Move the guide plate toward the front = the left
Register the basic value for paper in Cassette 3:
margin is increased
1) Set the STMTR/A4R size papers in Cassette 3,
and align the side guide plate with the STRTR/A4R [1]
width.
2) Select C3-STMRT/A4R to be highlighted, and
then by pressing the [ON] key, the numerical value
after auto adjustment are registered.
Cassette 4
COPIER> FUNCTION> CST> C4-STMTR/A4R
F-1-59
Perform the same operation as Cassette 3

4) Check that the left margin of the copied image from

the front deck left/right is as follows : L1=2.5 -/+
<Front Deck Left/Right>
1.5mm
1) Press the set release button to pull out the front deck
left/right toward the front.
2) Loosen the 2 screws [2] and the 2 fixing screws [3]
of the deck front cover [1].
image
[1]
L1

F-1-60

[1] Feeding direction of paper

5) Tighten the 4 screws loosened at the step 2)
6) Close the front deck left/right

24
 Chapter 1

ue)
<Manual Feeder Tray>
1) Move the side guide plate [1] to the center, and 1.2.21 Adjustment of
loosen the 2 screws [2] for the slide guide to adjust
the position of the slide guide.
image leading edge
margin 0015-4677
[2]
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N

1) Select the following in the service mode: COPIER

> ADJUST > FEED-ADJ > REGIST
[1]
2) Change the setting value to adjust.
(1mm shift by changing every 10 in the setting val-
F-1-61 ue)
Check that the leading edge margin of the image
Move the slide guide toward the back = the left picked up from each cassette/deck is as follows :
margin is reduced L1=4.0 +1.5 /-1.0mm
Move the slide guide toward the front = the left
margin is increased
2) Tighten the 2 screws loosened at the step 1)

[1] image
<Duplexing Feeder Unit>
1) Make the left margin of the 2nd sided image as
L1=2.5 -/+ 2.0mm by selecting the following in ser-
vice mode:
COPIER > ADJUST > FEED-ADJ > ADJ-REFE L1
F-1-63

[1]Feeding direction of paper

image
[1]
1.2.22 Mounting of the
L1

Host Machine 0015-4745

F-1-62 iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N
[1] Feeding direction of paper
Make the numerical value smaller = the left margin <Storing of the drum rotational tool and the grip>
is reduced 1) Detach the lower rear right cover [1].
Make the numerical value larger = the left margin is - 2 screws [2]
increased
(1mm shift by changing every 10 in the setting val-

25
 Chapter 1　

[2]

[1]

F-1-64
3) Attach the lower rear right cover removed in the
2) Store the following parts: step 1).
- Drum rotational tool [1]: store it along with the
collecting toner cap to the hole of the pullout grip at
the top of the collecting toner case [2]. <Attaching of the grip cover>
- Grip: insert to the grip storing area [3] 1) Attach the grip cover (small) [1] to the latch face
cover [2].
[1]
[2] [1]

[2]
[3]

F-1-65 F-1-66

2) Attach the 3 grip covers (large) [1] and the cover [2]
that was attached in the step 1).

If pulling out the pullout grip fully, it makes the

drum rotational tool and the cap fail to be insert-
ed.
It is easy to insert them if pulling the pullout grip
at moderate position shown in the figure below.

26
 Chapter 1

[1]

[1]

[1]
[2]
F-1-67
[1] 6mm or more [2]
<Attaching of the service book case>
1) Peel off the two-sided tape located at the back of the
service book case [1] to attach to the bottom plate
of the host machine.
Position forbidden to attach the ser-
vice book case
- Inside the machine (inner side of the front
cover)
- Position to block off the louver area
Be sure that the front side of the service book case
- Position to block off the grip area
is exposed for 6mm from the front side of the bot-
tom plate [2] of the host machine when attaching
the service book case.
In case of attaching the service book case without
any margin exposed from the bottom plate, it will
cause the service book case to run into the rail of
<Attaching of the shutdown label>
the paper deck when mounting the paper deck lat-
1) Put the appropriate language shutdown label [1] on
er.
Be sure to attach the paper deck first and then at- the indicated position.
tach the service book case in case of mounting the
paper deck and attaching the service book case at
the same time.

[1]

F-1-68

<Attaching of the document size label>

27
 Chapter 1　

1) Broaden the document size guide plate [1] for A3/

A3 position, and then fit the [A] of the document
side guide plate with the position of A4/A3 of the
document size label to attach the label.

A4
A A3

[1]

[2]

[1]

F-1-69

3) Fill in necessary information on the service book

<Attaching of the touch pen>
and store it to the service book case.
1) Set the touch pen [1] on the control panel.

[1]

F-1-70

<After installation of the host machine>

1) Clean around the machine.
2) Move the host machine to the specified position
and fix it in place with the 2 adjusters.

MEMO;
The adjusters may be too hard to turn by hand. In such
case, use a screwdriver to turn.

28
 Chapter 1

1.3 Checking the Connec-

tion to the Network
To set up the machine for networking, it is neces-
sary to enable [ON] for the following item in Ini-
1.3.1 Overview 0015-4748 tial Additional Functions :

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / > [System Settings] > [Network Setting] >
iR5055N [Change Setting/Display Connection Confirm]

The information in this section applies when connect-

ing the host machine to a network.
If the user's network is in TCP/IP environment, use the
PING command to see that the network settings are
correct. In case of reentering the IP address, turning off
There is no need to check the settings using the PING and then on the main power is required in order to
command if the use's network is in an IPX/SPX or Ap- be enabled.
ple Talk environment.

4) Perform the shutdown sequence so that the main

1.3.2 Checking the Con-
power can be turned off.
nection to the Network 0015-7620 5) Turn on the main power switch.

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N
1.3.3 Using the Ping
Command 0015-4749

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

The following steps apply only if the machine is

1) Make the following selections: > [System Set-
connected to a network.
tings] > [Network Settings] > [TCP/IP Settings] >
[Ping Command]
1) Perform the shutdown sequence so that the main
2) Using the keypad on the control panel, type in the
power can be turned off.
correct IP address set in [Network Connection], and
2) Connect the network cable to the host machine, and
press the Execute key.
turn on the main power switch.
If successful, the message 'Response from host' will
3) Inform the on-site system administrator that the in-
appear so that you can check that the IP address is
stallation work of the host machine is complete, and
valid; otherwise, the message will read 'No re-
also ask him/her to setup the host machine for net-
sponse from host'
working.

29
 Chapter 1　

1.3.4 Making a Check

Using the Remote Host
Address 0015-4750

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

You can execute the PING command using the appro-

priate remote host address to see if a connection to the
network is available.
Remote host address: the IP address of a PC terminal
connected to the TCP/IP network to which the ma-
chine is also connected.
1) Inform the system administrator that you are going
to check the network connection using the PING
command.
2) Check with the system administrator to find out the
remote host address.
3) Add the appropriate remote host address to the
PING command.
- If the message is 'Response from host', the connec-
tion to the network is normal.
- If the message is 'No response from host', the ma-
chine is not correctly connected to the network.
Start the troubleshooting work in the next section.

30
 Chapter 1

1.4 Troubleshooting the 1) Add the appropriate loopback address (127.0.0.1)

to the PING command.
Network - If the message is "No response from host," check
the machine's TCP/IP settings, and execute the
1.4.1 Troubleshooting the PING command once again.
- If the message is "Response from host," make the
Network 0015-4751 next check.

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N 1.4.4 Making a Check
Using a Local Host
The following information applies only when the ma-
chine is connected to a network.
Address 0015-4753
If attempts to connect to the network fail, suspect the
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
following:
iR5055N
- The machine's TCP/IP settings are wrong.
- The user's network is faulty.
The "local host address" is the IP address of the ma-
To find out which, go through the following:
chine, and the address comes back after reaching the
network PCB. By executing the PING command us-
1.4.2 Checking the Con- ing the address, you can find out whether the network
nection of the Network PCB is free of a fault.
1) Add the IP address of the machine to the PING
Cable 0015-7621 command.
If the message is "No response from host", go
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
through the following and execute the PING com-
iR5055N
mand once again.
- The machine's IP address may be wrong: Check
1) Check to be sure that the network cable is correctly
the machine's IP address settings, and check with
connected to the Ethernet port.
the system administrator to see if the assigned IP
- If the connection is correct, make the next check.
address is a valid one.
- If the connection is wrong, correct it and run the
- The connection of the network PCB may be
check once again using the remote host address.
wrong: Check the connection of the network PCB
once again.
1.4.3 Making a Check - The network PCB may be faulty. Try replacing it.
Using a Loopback If the message is "Response from host", suspect a
problem in the user's network environment. Report
Address 0015-4752 to the system administrator for appropriate action.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N

A loopback address comes back before reaching the

network PCB. By executing the PING command us-
ing the address, you can find out whether the ma-
chine's TCP/IP settings are correct.

31
 Chapter 1　

1.5 Installing the Copy 1.5.2 Power off of the

Tray host machine 0015-4768

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

1.5.1 Confirming the con- iR5055N

tents 0015-4767

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N
How to turn off the main power
When turn off the main power, implement the fol-
<Copy Tray L1>
lowing steps to protect the hard disk of this prod-
uct.
[2]
1) Push the control panel power switch for 3 sec or
more.
2) Operate the touch panel following the instruc-
[1]
tion on the screen of shutdown sequence in order
to be ready to turn off the main power switch.
3) Turn off the main power switch.
4) Pull out the power cable (for the outlet).

1.5.3 Installation proce-

dure 0015-4769

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

[3] [4] [5]

F-1-71

[1] Delivery Bar 1 pc. - When mounting the delivery Tray to the host ma-
chine, be sure to attach the rollers in the center of
[2] Delivery Tray 1 pc.
delivery roller.
[3] Magnet plate 1 pc. - When mounting the delivery tray to the host ma-
[4] Delivery roll 2 pc. chine, shift tray or finisher should not be mounted.

[5] E ring 1 pc.

1) Open the front cover.

2) Turn the fixing/feeding assembly release lever [1]
in the direction of the arrow to release the transfer/

32
 Chapter 1

separation charging unit. Slide the fixing/feeding

[1]
assembly [2] out.
[5]

[3]
[2] [4]

[6]
[1] [2]
F-1-72

3) Remove the delivery roller guide [1]. F-1-74

- 2 screws [2]

See the figure below to make sure the mounting di-

rection of the delivery roller's protrusion [1].
[2]
[2] [1] [1]
F-1-73

4) Attach the delivery roll.

- Attach the delivery roll [1] to the position of the
pin [3] found in the center of the delivery roller
shaft [2].
- Fit the protrusion [4] of one delivery roll to the [1]
mounting hole [5] of the other delivery roll.
- Fit E-ring [6] to the groove on the delivery roller 5) Mount the delivery roller guide.
shaft to mount. 6) Slide the fixing/feeding assembly in the machine
and close the front cover.
7) Detach the left cover (upper) [1].
- 2 screws [2]

33
 Chapter 1　

11) Attach the delivery tray bar [1].

[1]

[2] [1]
F-1-75

F-1-78
8) Attach the magnet plate [1] to the left cover (upper)
and bend the claws [2] at the both ends in the direc-
tion of the arrow.

[2]

[1]

F-1-76

9) Attach the left cover (upper).

10) Fit the protruding parts [1] at the delivery tray end
to the mounting holes [2] on the host machine.

[2]

[1]

[1]

F-1-77

34
 Chapter 1

1.6 Installing the Card [3] Toothed washer 1pc.

Reader <Card Reader Attachment-C2>

[1] [2]
1.6.1 Notice At Installa-
tion 0015-4772

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

[3] [4]

Installation of this equipment needs the card reader

attachment kit C2.

F-1-80
1.6.2 Confirming the con-
tents 0015-4773
[1] Card reader attachment plate 1pc.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N [2] Joint plate 1pc.

Screw
[3] 1pc.
<Card Reader-C1> (small panhead screw; M4X6)

[4] Screw (RS tightening; M4X10) 2pc.

[1] [2] [3]

1.6.3 Power off of the

C

host machine 0015-4774

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

F-1-79

[1] Card reader 1pc.

[2] Screw (RS tightening; M4X10) 1pc.

35
 Chapter 1　

How to turn off the main power

When turn off the main power, implement the fol-
lowing steps to protect the hard disk of this prod-
uct.
1) Push the control panel power switch for 3 sec or
more.
2) Operate the touch panel following the instruc-
tion on the screen of shutdown sequence in order
to be ready to turn off the main power switch.
3) Turn off the main power switch. [2] [1]

4) Pull out the power cable (for the outlet).

F-1-82

4) Attach the card reader to the joint plate [1] with 1

each of the toothed washer of the card reader and
the screw (RS tightening; M4X10) [2].
1.6.4 Installation proce-
dure 0015-4775

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Open the toner replacement cover.

2) Detach the Right cover (upper)[1].
- Screw [2] 2pc.
[2] [1]
F-1-83

5) Put the harness [1] of the card reader through the

hole [2] of the card reader attachment plate.

[1] [2]
F-1-81

3) Attach the card reader attachment plate [1].

- Screw (RS tightening; M4X10) [2] 2pc.
[1] [2]
F-1-84

6) Attach the card reader [1].

- Screw (small panhead screw; M4X6) [2] 1pc.

36
 Chapter 1

[1] [2] [1]

F-1-87

F-1-85 9) Put the cable [1] of the card reader through the 2
clamps [2].
7) Get the cable [1] out from the side of the host ma-
chine.

If the cable is difficult to remove, drivers etc.

will help make the operation easier.

[1] [2]
F-1-88

10) Cut the area [1] of the right cover (upper) with a
wire cutter etc.

[1]
F-1-89
[1]
F-1-86
11) Attach the right cover (upper) detached in the step
2).
8) Connect the card reader harness with the connector
12) Close the toner replacement cover.
[1].
13) Insert the power cable (for the plug).
14) Turn on the main power switch, and then check
the display demanding setting of the control card.
15) Input the card number (1 to 2001) to be used in the
service mode (COPIER > FUNCTION > IN-
STALL > CARD).

37
 Chapter 1　

- Input the smallest card number for the user to use.

- Up to 1,000 cards having been input are available.
16) Operate the touch panel following the instruction
on the screen of shutdown sequence in order to turn > [System Settings] > [System Maneger Set-
off the main power switch. tings] is selected and [System Maneger ID] and
17) Turn on the main power switch. [System Password] are registered, 'Registration of
18) Insert the control card and check the status where card to the device' is impossible to execute in the
copy is possible. setting of iWAM.

1.6.5 Installing for

imageWARE Account- > [System Settings] > [System Maneger Set-
tings], and then input any number into [System Ma-
ing Manager 0015-7624
neger ID] and [System Password].
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / 8) Press the reset key to escape the user mode screen.
iR5055N 9) Turn off the power according to the shutdown se-
quence.
1) Check to see that 'ID00000001 to ID00001000' has

been created in > [System Settings] > [Dep ID

Mangement] > [Registor Dept.ID/Password] >
[Page Totals]. (In the case that '1' has been input as
the first number by the service mode; COPIER >
FUNCTION > INSTALL > CARD)
2) Press the reset key to escape the user mode screen.

3) Select > [System Settings] > [Network Set-

tings] > [TCP/IP Settings] > [IP Address Settings],
and then make the setting of [IP Address], [Gate-
way Address], [Subnet Mask] according to the user
environment
4) Press the reset key to escape the user mode screen.
5) Operate the touch panel following the instruction
on the screen of shutdown sequence in order to turn
off the main power switch.
6) Turn on the main power switch.
7)

38
 Chapter 1

1.7 Installing the Original

Holder

1.7.1 Checking Contents 0015-4777

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N [1]

Document Tray-K1 F-1-91

2) Hook the document tray [1] to the stepped screws

tightened in the step 1.

[1]

[2] [3]
F-1-90

[1] Document Tray 1 pc. F-1-92

[2]* Stepped Screw (M4X31) 2 pc.

[3] Stepped Screw (M4X33) 2 pc.

* Not used with this host machine.

If it is hard to hook the document tray, loosen the
2 stepped screws and hook it once again.
1.7.2 Installation Proce-
dure 0015-4778

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

1.7.3 Checking Contents 0015-8032
iR5055N iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N
1) Tighten the 2 stepped screws (M4X33) [1] to the
upper cover (right). Document Tray-M1

39
 Chapter 1　

[1] [2]
F-1-93
[1]

[1] Document Tray 1pc.

[2] Stepped Screw (M4X33) 2 pc.

T-1-4 F-1-95

MEMO;
For the 120V model, use it as stan-
dard.

If it is hard to hook the document tray, loosen the

2 stepped screws and hook it once again.
1.7.4 Installation Proce-
dure 0015-8034

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

1) Tighten the 2 stepped screws (M4X33) [1] to the

upper cover (right).

[1]
F-1-94

2) Hook the document tray [1] to the stepped screws

tightened in the step 1.

40
 Chapter 1

1.8 Installing the Reader

Heater How to turn off the main power
When turn off the main power, implement the fol-
lowing steps to protect the hard disk of this prod-
1.8.1 Checking the Con- uct.
tents 1) Push the control panel power switch for 3 sec or
0015-7877
more.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / 2) Operate the touch panel following the instruc-
iR5055N tion on the screen of shutdown sequence in order
to be ready to turn off the main power switch.
<Reader Heater Kit> 3) Turn off the main power switch.
4) Pull out the power cable (for the outlet).
[1] [2] [3] [4] [5]

1.8.3 Installation Proce-

F-1-96
dure 0015-7814
T-1-5
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
[1] Mirror Heater FK2-0229 1pc iR5055N
[2] Lens Heater FK2-0228 1pc
1) Open the DADF.
[3] Cable Clamp WT2-0507 2pc
2) Remove the glass retainer [1].
[4] Heater Harness Retainer FC5-2945 1pc
- Remove the 2 screws [2]
[5] Screw (RS tightening; XB3-6400 4pc 3) Remove the copyboard glass [3]
M4X8)

1.8.2 Power off of the

host machine 0015-7815
[2]
[3]

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

[1]
F-1-97

41
 Chapter 1　

and then tighten with the 2 screws (RS tightening;

M4X8) [4].

When removing the copyboard glass, be sure not to

get your fingers touched with the glass surface or
the backside of the white plate.
In case the glass is soiled, clean it with lint-free pa-
per.
[3]

[2] [1]
[4]

[1]

[4]

F-1-100

6) Attach the heater harness retainer [1].

- 1 screw (RS tightening; M4X8) [2]

[1] [2]

F-1-98

4) Hold the tab (the bend) [A] of the mirror stay to

move the No. 1 mirror base [1] to the right until it
stops.
F-1-101
[1]
[A] 7) Hold the tab (the bend) [A] of the mirror stay to
move the No. 1 mirror base [1] to the left until it
stops.

F-1-99

5) Insert the front side of the mirror heater [1] under

the cable guide [2] and connect the connecter [3],

42
 Chapter 1

Tighten the screw [3] while pushing on the lens

[1]
heater [1] in the direction of the emboss [2]. Be
sure that the heater's claw [4] must not be disen-
gaged when performing this operation. Also check
that the bottom of the heater must not be off from
[A] the board.
F-1-102

8) Insert the cable clamp [1] to the hole [2] of the

frame. [2]

[1]
[4]

[3]

[1]

[2]
F-1-105

F-1-103 10) In case that the cable [1] is loose, insert the cable
clamp [2] to the frame's hole to fix the cable in
9) Attach the lens heater [1] place.
- 1 connector [2]
[1] [2]
- 1 cable clamp [3]
- 1 screw (RS tightening; M4X8) [4]

[2]

[3]

[4]
F-1-106
[1]

F-1-104 11) By reversing the steps used to remove, attach the

copyboard glass and the glass retainer.
12) Close the DADF.
13) Shift the cassette heater switch [1] and the envi-
ronment switch [2] to the on position.

43
 Chapter 1　

[1] ON

[2]

F-1-107

44
 Chapter 1

1.9 Installing the Cassette

Heater How to turn off the main power
When turn off the main power, implement the fol-
lowing steps to protect the hard disk of this prod-
1.9.1 Checking Compo- uct.
nents 1) Push the control panel power switch for 3 sec or
0015-7889
more.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / 2) Operate the touch panel following the instruc-
iR5055N tion on the screen of shutdown sequence in order
to be ready to turn off the main power switch.
<Cassette Heater> 3) Turn off the main power switch.
4) Pull out the power cable (for the outlet).
[1] [2] [3]

F-1-108 1.9.3 Installation Proce-

dure of the Cassette
Heater 0015-4781
[1] heater unit FM2-4182-000 1pc.

[2] cassette stay FB2-7052-000 1pc. iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N
[3] screw (M4X6) XB1-2400-609 6pc.

1.9.2 Power off of the

host machine 0015-7816
Be sure to disconnect the power outlet.
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /
iR5055N
1) Open the wire saddle [1] to disengage the reader
communication cable [2].

[1] [2]

F-1-109

45
 Chapter 1　

2) Detach the upper rear cover [1].

- 6 screws [2] [2] [1]

[2]

[1]

[3] [2]
F-1-112
[2]
F-1-110 5) Hold down the release button [1] to slide Cassette 4
[2] out.
3) Detach the lower rear cover [1].
- 6 screws [2]

[2]
[1]

[2]
[2]
[2]
F-1-113

[2]
6) Lift the inner unit [1] in Cassette 4, and remove it.

[1] [2]
F-1-111

4) Remove the heat exhaust fan (filter) [1].

- 3 screws [2]
- 1 connector [3]

[1]
F-1-114

7) In the same way, remove the inner unit of Cassette

3.
8) Engage the claw [A] of the lead edge onto the long

46
 Chapter 1

hole [B] of the host machine to attach the cassette

stay [1].

[B]

[A]

[1]
[1]
[2]
F-1-116
F-1-115
10) Secure the cassette stay [1] in place from the front
side of the host machine.
- 2 screws [2] (M4X6)

Make sure from the rear side of the host machine

that the claw [A] of the cassette stay is engaged ap-
propriately.

[1]
[2]

[A] F-1-117
[A]

11) Put the cassette heater connector [1] through the

long hole [A], while at the same time hook the met-
al plate [B] on the rear side of the cassette heater [2]
onto the hole [C] of the cassette heater.

Make sure that the heater cord guide [3] is fitted in

place appropriately on to the long hole [A].
9) Secure the cassette stay [1] in place from the rear
side of the host machine.
- 2 screws (M4X6) [2].

47
 Chapter 1　

[C] [B] [2]

[B]

[A]

[1]

F-1-119

[2]
14) Attach the covers etc., by the reverse procedure to
[1] detach them.
- heat exhaust fan (filter)
- lower rear cover
- upper rear cover
- Secure the reader communication cable in the wire
saddle.
15) Fit the inner units in each cassette in place, and
then attach the cassettes onto the host machine.
[3] [3] 16) Connect the power supply cable (for power outlet)
of the host machine.
12) Lift the cassette heater [1] until it touches the host 17) Turn on the main power switch.
machine, and then secure it in place at the specified
position with the 2 screws (M4X6) [2].

[1] [2]
F-1-118

13) Connect the connector [1] on the host machine and

the cassette heater connector [2].

48
 Chapter 1

1.10 Installing the Deck [4]

Heater [3] [6]

1.10.1 Checking the [8]

Parts to Install 0016-0491

[8]
iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / [10]
[5]
iR5055N
[2]
[5]
Every components of the cassette heater unit are sup- [7]

plied as service parts, so have the following parts on

hand.
[9] [12]

F-1-120

T-1-6

N Part name Part num- QTY No. Part name Part number QTY
o. ber

[1 FG6- 1pc. [7] FS6-8725 1pc.

] Heater unit 9651 Power supply label

[2 AC input con- FG6- 1pc. [8] XB1-2400-409 4pcs.

] nector 1117 Binding screw (M4 X 4)

[3 Relay harness FG6- 1pc. [9] Wire saddle (Not used for this prod- WT2-5730 3pcs.
] unit 2957 uct)

[4 FK2- 1pc. [10] FC7-5473 1pc.

] AC cable 4379 Power supply code base

[5 Screw (w/ XB2- 3pcs. [11] Screw (w/ flat spring) XB2-8401-007 1pc.
] washer) 7400-607

[6 Cable protec- WT2- 1pc. [12] Wire saddle WT2-5738 1pc.

] tion bush 5098

49
 Chapter 1　

1.10.2 Turning Off the

Host Machine 0016-1684

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

Turning Off the Main Power of the Host Machine

When turning off the main power, be sure to go
through the following in strict sequence to protect the
machine's hard disk:
[1] Hold on the power switch on the control panel 3
sec or more.
[2] Operate on the touch panel according to the shut-
down sequence indicated so that the main power
switch may be turned off.
[3] Turn off the main power switch.
[4] Disconnect the power cable (for the power outlet).

50
 Chapter 1

1.11 Installing the Deck

Heater (Large Deck)

1.11.1 Checking the

[3]
[6]
Parts to Install 0016-1496

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N [8]
A

Every components of the cassette heater unit are sup-

plied as service parts, so have the following parts on
[5]
hand.

[5]

[7]

[12]

F-1-121

T-1-7

N Part name Part num- QTY No. Part name Part number QTY
o. ber

[1 FG6- 1pc. [7] FS6-8725 1pc.

] Heater unit 9651 Power supply label

[2 AC input con- FG6- 1pc. [8] XB1-2400-409 4pcs.

] nector 1117 Binding screw (M4 X 4)

[3 Relay harness FG6- 1pc. [9] Wire saddle WT2-5730 3pcs.

] unit 2957

[4 FK2- 1pc. [10] FC7-5473 1pc.

] AC cable 4379 Power supply code base

[5 Screw (w/ XB2- 3pcs. [11] Screw (w/ flat spring) XB2-8401-007 1pc.
] washer) 7400-607

[6 Cable protec- WT2- 1pc. [12] Wire saddle WT2-5738 1pc.

] tion bush 5098

51
 Chapter 1　

1.11.2 Turning Off the

Host Machine 0016-1691

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N /

iR5055N

Turning Off the Main Power of the Host Machine

When turning off the main power, be sure to go
through the following in strict sequence to protect the
machine's hard disk:
[1] Hold on the power switch on the control panel 3
sec or more.
[2] Operate on the touch panel according to the shut-
down sequence indicated so that the main power
switch may be turned off.
[3] Turn off the main power switch.
[4] Disconnect the power cable (for the power outlet).

52
 Chapter 1

1.12 Installing the Voice Guidance Kit

1.12.1 A point to keep in mind at installation 0015-7208

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

When installing the machine, see the Combination Table for Accessory Installation.

Before starting to install the Voice Guidance Kit, check to be sure that the Expansion Bus-D2 has properly been
installed.

1.12.2 Checking the Contents 0015-4782

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

<Voice Guidance Kit-B1>

[1] [2] [3] [4] [5] [6]

[7] [8] [9] [10] [11] [12] [13] [14] [15]

[16] [17]
F-1-122

53
 Chapter 1　

[1] Speaker Unit (Upper) 1pc. [2] Speaker Unit (Lower) 1pc.

[3] Cable (1300 mm) 1pc. [4]* Cable (1850 mm) 1pc.

[5] Cable Guide 7pc. [6] Voice Board 1pc.

(this machine requires 6 cord guides)

[7] Voice Board instruction plate 1pc. [8]* Voice Board instruction plate 1pc.

[9] Screw (binding; M3X6) 2pc. [10] Screw (binding; M4X6) 1pc.

[11] Screw (binding; M4X40) 2pc. [12]* Screw (binding; M3X16) 1pc.

[13]* Screw (binding; M4X16) 1pc. [14] Ferrite Core 1pc.

[15]* Wire Saddle 1pc. [16] Voice Guidance Kit Users Guide 1pc.

[17] Voice Guidance Kit Users Guide CD 1pc.

* Not used for this machine

1.12.3 Power off of the host machine 0015-4783

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

How to turn off the main power

When turn off the main power, implement the following steps to protect the
hard disk of this product.
1) Push the control panel power switch for 3 sec or more.
2) Operate the touch panel following the instruction on the screen of shutdown
sequence in order to be ready to turn off the main power switch.
3) Turn off the main power switch.
4) Pull out the power cable (for the outlet).

1.12.4 Installation Procedure 0015-4784

iR5065 / iR 5055 / iR5075 / iR5075N / iR5065N / iR5055N

1) Open the cable clamp [1], and disconnect the reader communications cable [2].

54
 Chapter 1

[1] [2]

F-1-123

2) Detach the upper rear cover [1].

- 6 screws [2]

[2]

[1]

[2]
F-1-124

3) Detach the main controller box cover [1].

- 4 screws [2]

55
 Chapter 1　

[1]

[2]
F-1-125

4) Remove the face cover plate [1]. (The removed plate is not used after this step.)
- 2 screws [2]

[2] [1]
F-1-126

5) Attach the Voice Board instruction plate [2] to the voice board [1].
- 2 screws (binding; M3X6) [3]

56
 Chapter 1

[3] [2]

[1]

F-1-127

Checking the Position of the Slide Switch (SW1) on the Voice Guidance Board
The slide switch (SW1) on the Voice Guidance Board is provided as a means of switching frequencies (33 MHz/
66 MHz) to suit the transfer speed of the PCI bus. It is important for the switch setting to suit the transfer speed
so that the voice will be free of interruption. If you inadvertently moved the slide, be sure to put it back to its
correct position. For the Boad, the frequency must be set to 66 MHz.

33MHz

66MHz

6) Mount the voice board [1] to the PCI Expansion Kit-D2 using the 2 screws [2] removed in step 4).

57
 Chapter 1　

Cautions in mounting
- A voice board [1] must be mounted to a specified position.
Be sure to mount it to the slot [A] on the Expansion Bus B-1 board.
Do not mount it to the slot [B] or [C].
- If other board is mounted to the slot [A] , pull the board out of the slot and mount it to other slot. Then, mount
a voice board to the slot [A] .
- Be sure that the PCB is perpendicular to the connector.

[C] [C]
[A] [B] [A] [B]

[2]
[1]

7) Attach the removed parts.

- Main controller box cover
- Upper rear cover
8) Connect the reader communication cable.
9) Close the reader communication cable with the wire saddle.
10) Mount the speaker Unit (Lower) [1] to the upper right cover of the host machine.
- 2 screws (binding; M4X40) [2]

[1]

[2]

F-1-128

58
 Chapter 1

11) Mount the speaker unit (upper) [1] on the speaker unit (lower), fix them with a screw (binding; M4X6) [2] from
beneath.

[1]

[2]

F-1-129

12) Take off the cover [1] from the code guide.

[1]

F-1-130

13) Peel off the released paper of the code guide [1] and affix it to the host machine as shown in the figure.

The right side --- 2 places

59
 Chapter 1　

[1]

F-1-131

The rear -- 4 places

[1]

[1]

[1]

F-1-132

14) Connect the cable [2] into the speaker unit [1].

[1]

[2]

F-1-133

60
 Chapter 1

15) Run the cable [1] through the cable guide [2] and mount the cable guide cover [3].

There should no excessive bending of the cable.

[1]
[2]

[3]

F-1-134

16) Attach the ferrite core [1] to the cable. Be sure that the length [2] is 50 mm or shorter.

[1]

[2]

F-1-135

17) Connect the cable [1] to the terminal [2] of the voice board.

[2]

[1]

F-1-136

61
 Chapter 1　

18) Run the cable [1] through the code guide [2] and mount the code guide cover [3].

There should no excessive bending of the cable.

[2]

[3]

[2]

[1] [3]

[2]

[3]

F-1-137

19) Connect the power cable to the outlet.

20) Turn ON the main power switch.
21) Check if the voice board is recognized.
Service mode
Select COPIER > DISPLAY > ACC-STS > PCI
If "Voice Board" is displayed, that means that the voice board is correctly recognized.

2. Setting After Installation

To use 'voice guidance' after power-on, it is necessary to set the followings.
1) [Additional Functions] > [System Settings] > [Voice Navigation Management Settings] > [Use Voice Guide]
2) Check that it is set to ON.

3. Operation Check
<When Using the Voice Guidance>
1) Press the reset key for 3 sec or longer.
2) When the display of the number of copy is enclosed with red lines on the screen, "Voice Guidance" becomes
enabled.

<When Stopping the Usage>

62
 Chapter 1

1) Press the reset key for 3 sec or longer.

63
 Chapter 1　

64