GF-WPKF-J-DS-1506 DATA SHEET FOR MANUAL VALVES PAGE 1 OF 41

PROVISION FOR ENGINEERING,PROCUREMENT,CONSTRUCTION

COMMISSIONING(EPCC) OF OIL GATHERING FACILITIES PHASE 4
FOR PETRONAS CARIGALI IRAQ HOLDING B.V.S,GARRAF OPERATIONS

CONTRACT NO.: PCIHBV/2017/PD&T/1864

DATA SHEET FOR MANUAL VALVES

GF-WPKF-J-DS-1506

EPPM / ATCO

PREPARED BY CHECKED BY APPROVED BY PCHIBV’s COMMENT

Rev Date Description
Name & Sign Name & Sign Name & Sign □ Approved / Reviewed

1 12/06/2019
RE-ISSUED FOR
CONSTRUCTION
RNO AJ MMH □ Approved with Comment

□ Resubmit for Approval

□ Resubmit for Review

Name Signature Title Date

MHMS PIPING 15/06

The signing, countersigning or other endorsements of any drawings and documentation by PCIHBV’s Representatives, agents or
employees shall neither be interpreted as implying the responsibility for the correctness and accuracy of such documents nor
relieving the CONTRACTOR of its obligations to review all information, data, drawings, and specifications provided by PCIHBV
CLASS1
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 2 OF 41

REVISION HISTORY

Rev. Date Revision Description

A 27/12/2018 ISSUED FOR REVIEW AND APPROVAL

0 30/05/2019 ISSUED FOR CONSTRUCTION

1 12/06/2019 RE-ISSUED FOR CONSTRUCTION

 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 3 OF 41

1.0 VALVE CODE SYSTEM

The first two digits designate the type of valves:
GA Gate Valve
GL Globe Valve
CP Piston Lift Check Valve
CW Wafer Lug Check Valve
CS Swing Check Valve
BF Ball valve Full Bore
BR Ball Valve Reduced Bore
DB Double Block & Bleed Valve
NE Needle Valve
BU Butterfly Valve

The third digit designates ASME Class Rating:

1 ASME Class 150
2 ASME Class 300
3 ASME Class 600
4 ASME Class 800
5 ASME Class 900
6 ASME Class 1500
7 ASME Class 2500

The fourth digit designates end connections:

1 Raised Face (3.2 to 6.3 µm)
2 Flat Face
3 Ring Type Joint
4 Socket Weld
5 NPT (F)
6 Socket Weld x NPT (F)
7 Flanged RF x NPT (F)
8 Flanged RTJ x NPT (F)
9 Wafer Lug (Between RF Flanges)
0 Wafer Lug (Between FF Flanges)
A Raised Face (6.3-12.5 µm)
B Wafer Lug (Between RF Flanges 6.3-12.5µm)

The fifth digit designates body materials:

1 ASTM A105N
2 ASTM A216 Gr. WCB
3 ASTM A350 Gr. LF2 CL.1
4 ASTM A352 Gr. LCC
5 ASTM A182 Gr. F316/316L
6 ASTM A351 Gr. CF8M
7 ASTM B564 UNS N06625
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 4 OF 41

The fifth digit designates body materials: (Cont.)

8 ASTM A494 CW6MC
9 ASTM B148 UNS C95400
A ASTM A182 Gr. F51
B ASTM A890 Gr. 4A
C ASTM A182 Gr. F52
D ASTM A890 Gr. 5A
E ASTM A216 Gr. WCB + 3mm UNS S32950 Weld Overlay
F ASTM A105N + 3mm UNS S32950 Weld Overlay

The sixth digit designates trim materials:

0 UNS S32950 with PTFE seat
1 CS + 3mm UNS S32950 Weld Overlay with PTFE seat
2 UNS S32950 with PEEK seat
3 CS + 3mm UNS S32950 Weld Overlay with PEEK seat
4 SS316 + Stellite 6
5 SS316 with PTFE seat
6 SS316 with Filled PTFE seat
7 SS316 with PEEK seat
8 UNS S32950 + Stellite 6
9 CS + 3mm UNS S32950 Weld Overlay
A UNS N06625 + Stellite 6
B UNS N06625 with PEEK seat
C Aluminium Bronze
D Inconel 625 with PTFE seat
E CS + 3mm Inconel 625 Weld Overlay
F 13%Cr + Stellite 6
G CS + 3mm 13%Cr Weld Overlay
H 13%Cr with PTFE seat
J 13%Cr with PEEK seat
K Monel + Stellite 6
L CS + 3mm Monel Weld Overlay
M Monel with PTFE seat
N Monel with PEEK seat
P UNS S31803 with PEEK seat
Q UNS S31803 + Stellite 6
R CS + 3mm Monel Weld Overlay with PTFE seat
S CS + 3mm 13%Cr Weld Overlay with PTFE seat
T CS + 3mm 13%Cr Weld Overlay with PEEK seat
V CS + 3mm Inconel 625 Weld Overlay with PTFE seat
W CS + 3mm Inconel 625 Weld Overlay with PEEK seat
U CS + 3mm SS316 Weld Overlay
X UNS S31803+PTFE seat
Y CS + 3mm UNS S31803 Weld Overlay with PTFE seat
Z CS + 3mm UNS S31803 Weld Overlay
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 5 OF 41

The seventh digit designates the operator type:

A Automatic
L Lever Operated
H Handwheel Operated
G Gear Operated

The eighth digit designates the service requirement:

N Sour Service

The ninth digit designates specific requirements:

Specific Requirements (*)
For eg. Corrosion allowance=6mm, extended bonnet etc.
X
Note: Specific requirement descriptions shall be marked with
“*” mark in valve data sheets.

For example, Valve Tag Number GA1114HN is Gate Valve, 150#, Raised Face, Body:
ASTM A105N, Trim: SS316 + Stellite 6, Handwheel operated, Sour Service (NACE
MR0175 / ISO 15156).
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 6 OF 41

2,0 INDEX OF MANUAL VALVES DATA SHEET

Valve Code SIZE RANGE
Sr No. Piping Class Description RATING Page Number
System FROM TO
1 BR112HLN 011440XG Ball Valve (RB) 150# 2" 4" 7
2 BR112MLNX 011440YG Ball Valve (RB) 150# 2" 4" 8
3 BR1115L 011412XG Ball Valve (RB) 150# 1/2" 1" 1/2 9
4 BR1125L 011412XG Ball Valve (RB) 150# 2" 4" 10
5 BR211HLNX 031440XG/031440RG Ball Valve (RB) 300# 1/2" 1" 1/2 11
6 BR212HLNX 031440XG/031440RG Ball Valve (RB) 300# 2" 4" 12
7 BF212HLNX 031440RG Ball Valve (FB) 300# 2" 4" 13
8 BR212HGNX 031440RG Ball Valve (RB) 300# 6" 8" 14
9 - - Ball Valve (RB) 600# 1/2" 1" 1/2 15
10 BR512JLNX 091440XG Ball Valve (RB) 900# 3" 3" 16
11 BR512JGNX 091440XG Ball Valve (RB) 900# 4" 8" 17
12 BR512TGNX 091440XG Ball Valve (RB) 900# 10" 20" 18
13 BR611JLNX 091440XG Ball Valve (RB) 1500# 1" 1" 1/2 19
14 BR612JLNX 091440XG Ball Valve (RB) 1500# 2" 3" 20
15 BR6157L - Ball Valve (RB) 1500# 1/2" 1" 1/2 21
16 GL111KHNX 011440YG Globe Valve 150# 1/2" 1" 1/2 22
17 GL112KHNX 011440YG Globe Valve 150# 2" 8" 23
18 GL212FHNX 031440XG/031440RG Globe Valve 300# 2" 8" 24
19 GL512FHNX 091440XG Globe Valve 900# 3" 3" 25
20 GL512FGNX 091440XG Globe Valve 900# 4" 8" 26
21 GL611FHNX 091440XG Globe Valve 1500# 1" 1" 1/2 27
22 GL612FHNX 091440XG Globe Valve 1500# 2" 3" 28
23 BR212SGNX 031440RG Ball Valve (RB) 300# 18" - 29
24 CW192KANX 011440YG Check Valve 150# 2" 8" 30
25 CW1924A 011412XG Check Valve 150# 31
26 CW292FANX 031440RG Check Valve 300# 2" 8" 32
27 CW292GANX 031440RG Check Valve 300# 10" 24" 33
28 CW592FANX 091440XG Check Valve 900# 3" 8" 34
29 CW592GANX 091440XG Check Valve 900# 10" 20" 35
30 DB171MLNX 011440YG DBB Valve 150# 1/2" 2" 36
31 DB271HLNX 031440XG/031440RG DBB Valve 300# 1/2" 2" 37
32 - - DBB Valve 600# 1/2" 1" 1/2 38
33 DB611JLNX 091440XG DBB Valve 1500# 1" 2" 39
34 DB671JLNX 091440XG DBB Valve 1500# 1" 2" 40
35 DB6757L 153411XG DBB Valve 1500# 1/2" 1" 1/2 41
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 7 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR112HLN
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 2" TO 4"

VALVE ASME CLASS/RATING 150#

VALVE PORT REDUCED BORE

PIPING CLASS 011440XG

CORROSION ALLOWANCE 3.0 MM

PROCESS FLUID, CLOSED & OPEN DRAINS, VENT (ATM), FLARE (ATM), FUEL GAS,
VALVE SERVICE
PROCESS GAS (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 5)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PTFE (NOTE 7)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
6. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

7. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 8 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR112MLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 2" TO 4"

VALVE ASME CLASS/RATING 150#

VALVE PORT REDUCED BORE

PIPING CLASS 011440YG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE CLOSED & OPEN DRAINS, PROCESS WATER (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL MONEL

STEM / TRIM MONEL

PRIMARY SEAT RING PTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 9 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR1115L
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 150#

VALVE PORT REDUCED BORE

PIPING CLASS 011412XG

CORROSION ALLOWANCE 1.0 MM

VALVE SERVICE UTILITY AIR, NITROGEN, VENT
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PTFE

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

BOLTING ASTM A193-B7 / ASTM A194-2H (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-WP3-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 10 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR1125L
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 2" TO 4"

VALVE ASME CLASS/RATING 150#

VALVE PORT REDUCED BORE

PIPING CLASS 011412XG

CORROSION ALLOWANCE 1.0 MM

VALVE SERVICE UTILITY AIR, NITROGEN, VENT
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PTFE

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

BOLTING ASTM A193-B7 / ASTM A194-2H (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-WP3-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 11 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR211HLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE (NOTE 9)

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 300#

VALVE PORT REDUCED BORE

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING RPTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.
5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.

9. PIPELINE VALVES SHALL BE PROVIDED AS PER PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 12 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR212HLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE (NOTE 9)

VALVE SIZE RANGE 2" TO 4"

VALVE ASME CLASS/RATING 300#

VALVE PORT REDUCED BORE

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING RPTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.

9. PIPELINE VALVES SHALL BE PROVIDED AS PER PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 13 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : BF212HLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE (NOTE 9)

VALVE SIZE RANGE 2" TO 4"

VALVE ASME CLASS/RATING 300#

VALVE PORT FULL BORE

PIPING CLASS 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.
5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.

9. PIPELINE VALVES SHALL BE PROVIDED AS PER PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 14 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR212HGNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE (NOTE 9)

VALVE SIZE RANGE 6" TO 8"

VALVE ASME CLASS/RATING 300#

VALVE PORT REDUCED BORE

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION GEAR OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING RPTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.

9. PIPELINE VALVES SHALL BE PROVIDED AS PER PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 15 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER :
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 600#

VALVE PORT REDUCED BORE

PIPING CLASS -

CORROSION ALLOWANCE (*) 0.0 MM

VALVE SERVICE CHEMICAL INJECTION

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A182 GR.F316/316L

COVER/BONNET ASTM A182 GR.F316/316L

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A320-L7 / ASTM A194-7 (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 16 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR512JLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 3"

VALVE ASME CLASS/RATING 900#

VALVE PORT REDUCED BORE

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

BOLTING ASTM A193-B7M / ASTM A194-2HM (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.050 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 17 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR512JGNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 4" TO 8"

VALVE ASME CLASS/RATING 900#

VALVE PORT REDUCED BORE

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION GEAR OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

BOLTING ASTM A193-B7M / ASTM A194-2HM (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.050 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 18 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR512TGNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 10" TO 20"

VALVE ASME CLASS/RATING 900#

VALVE PORT REDUCED BORE

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION GEAR OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL CARBON STEEL + 3MM 13%CR WELD OVERLAY

STEM / TRIM 13%CR

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

BOLTING ASTM A193-B7M / ASTM A194-2HM (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
SP-1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.050 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 19 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR611JLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 1" TO 1 1/2"

VALVE ASME CLASS/RATING 1500#

VALVE PORT REDUCED BORE

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 20 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR612JLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 2" TO 3"

VALVE ASME CLASS/RATING 1500#

VALVE PORT REDUCED BORE

PIPING CLASS 151440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING PEEK (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 21 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR6157L
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTEGRAL BONNET (NON-EXTENDED) BALL VALVE

VALVE SIZE RANGE 1" TO 1 1/2"

VALVE ASME CLASS/RATING 1500#

VALVE PORT REDUCED BORE

PIPING CLASS -

CORROSION ALLOWANCE (*) 0.0 MM

VALVE SERVICE CHEMICAL INJECTION

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A182 GR.F316/316L

COVER/BONNET ASTM A182 GR.F316/316L

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PEEK

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A320-L7 / ASTM A194-7 (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 22 OF 41
DATA SHEET FOR
GLOBE VALVES

VALVE TAG NUMBER : GL111KHNX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 150#

PIPING CLASS 011440YG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE CLOSED & OPEN DRAINS, PROCESS WATER (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM

VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT INTEGRAL

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC MONEL + STELLITE 6

STEM / TRIM MONEL

GLAND RING MONEL

BODY SEAT RING STELLITE 6

BACK SEAT STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 15761

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 23 OF 41
DATA SHEET FOR
GLOBE VALVES

VALVE TAG NUMBER : GL112KHNX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 2" TO 8"

VALVE ASME CLASS/RATING 150#

PIPING CLASS 011440YG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE CLOSED & OPEN DRAINS, PROCESS WATER (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN
BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM
VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT RENEWABLE

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

DISC MONEL + STELLITE 6

STEM / TRIM MONEL

GLAND RING MONEL

BODY SEAT RING MONEL + STELLITE 6

BACK SEAT MONEL + STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS 1873

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 24 OF 41
DATA SHEET FOR
GLOBE VALVES

VALVE TAG NUMBER : GL212FHNX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 2" TO 8"

VALVE ASME CLASS/RATING 300#

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM

VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT RENEWABLE

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

DISC 13%CR + STELLITE 6

STEM / TRIM 13%CR

GLAND RING 13%CR

BODY SEAT RING 13%CR + STELLITE 6

BACK SEAT 13%CR + STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS 1873

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 25 OF 41
DATA SHEET FOR
GLOBE VALVES
VALVE TAG NUMBER : GL512FHNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 3"

VALVE ASME CLASS/RATING 900#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)
DESIGN
BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM
VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT RENEWABLE

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

DISC 13%CR + STELLITE 6

STEM / TRIM 13%CR

GLAND RING 13%CR

BODY SEAT RING 13%CR + STELLITE 6

BACK SEAT 13%CR + STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

SPIRAL WOUND GASKET,AISI 316L, GRAPHITE FILLED, CS CENTERING / SS INNER
GASKET
RING
BOLTING ASTM A193-B7M / ASTM A194-2HM (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS 1873

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING DOC. NO. GF-WP3-R-SP-1001.

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE FILLED BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.05 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 26 OF 41
DATA SHEET FOR
GLOBE VALVES
VALVE TAG NUMBER : GL512FGNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 4" TO 8"

VALVE ASME CLASS/RATING 900#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)
DESIGN
BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, NON RISING HAND WHEEL,
VALVE DESIGN
RISING STEM
VALVE OPERATION GEAR OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT RENEWABLE

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

DISC 13%CR + STELLITE 6

STEM / TRIM 13%CR

GLAND RING 13%CR

BODY SEAT RING 13%CR + STELLITE 6

BACK SEAT 13%CR + STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

SPIRAL WOUND GASKET,AISI 316L, GRAPHITE FILLED, CS CENTERING / SS INNER
GASKET
RING

BOLTING ASTM A193-B7M / ASTM A194-2HM (Zn METAL COATED + FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS 1873

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING DOC. NO. GF-WP3-R-SP-1001.

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE FILLED BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.05 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 27 OF 41
DATA SHEET FOR
GLOBE VALVES

VALVE TAG NUMBER : GL611FHNX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 1" TO 1 1/2"

VALVE ASME CLASS/RATING 1500#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM

VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT INTEGRAL

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC 13%CR + STELLITE 6

STEM / TRIM 13%CR

GLAND RING 13%CR

BODY SEAT RING STELLITE 6

BACK SEAT STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 15761

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 28 OF 41
DATA SHEET FOR
GLOBE VALVES

VALVE TAG NUMBER : GL612FHNX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE GLOBE VALVE

VALVE SIZE RANGE 2" TO 3"

VALVE ASME CLASS/RATING 1500#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR)
VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN
BOLTED BONNET, OS & Y TYPE, STRAIGHT PATTERN, RISING HAND WHEEL, RISING
VALVE DESIGN
STEM
VALVE OPERATION HANDWHEEL OPERATED

DISC SWIVEL PLUG DISC TYPE

SEAT / BACKSEAT RENEWABLE

STEM PACKING RENEWABLE

MATERIALS (NOTE 3, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

DISC 13%CR + STELLITE 6

STEM / TRIM 13%CR

GLAND RING 13%CR

BODY SEAT RING 13%CR + STELLITE 6

BACK SEAT 13%CR + STELLITE 6

GLAND FLANGE ASTM A105N

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN/ PREFORMED COMP.GRAPHITE

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS 1873

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

5. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 29 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : BR212SGNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE SPLIT BODY BOLTED BONNET (NON-EXTENDED) BALL VALVE (NOTE 9)

VALVE SIZE RANGE 18"

VALVE ASME CLASS/RATING 300#

VALVE PORT REDUCED BORE

PIPING CLASS 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 5, 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE END CONFIGURATION FLANGED (RF) , SMOOTH FINISH (Ra 3.2 to 6.3µm)

DESIGN

VALVE DESIGN SOLID BALL, FIRE SAFE, ANTISTATIC, BI DIRECTIONAL, LONG PATTERN

VALVE OPERATION GEAR OPERATED

BALL SUPPORT TRUNNION MOUNTED

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A216 GR.WCB

COVER/BONNET ASTM A216 GR.WCB

BALL 13%CR

STEM / TRIM 13%CR

PRIMARY SEAT RING RPTFE (NOTE 8)

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED +

BOLTING
FLUROCARBON COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 6D

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPELINE VALVES (DOC. NO. GF-OGF4-P-SP-

NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

AS PER SPECIFICATION FOR COATING AND PAINTING (DOC. NO. GF-OGF4-R-SP-

PAINTING
1001)
MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

5. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION PIPELINE VALVES DOC. NO. GF-OGF4-P-SP-1001.
9. PIPELINE VALVES SHALL BE PROVIDED AS PER PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 30 OF 41
DATA SHEET FOR
CHECK VALVES

VALVE CODE NUMBER : CW192KANX

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 2" TO 8"

VALVE ASME CLASS/RATING 150#

PIPING CLASS 011440YG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE CLOSED DRAIN, OPEN DRAIN, PROCESS WATER (SOUR)
VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS (NOTE 3, 5)

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) MONEL + STELLITE 6

BODY SEAT RING MONEL + STELLITE 6

HINGE / HINGE PIN MONEL

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

6. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 31 OF 41
DATA SHEET FOR
CHECK VALVES

VALVE CODE NUMBER : CW1924A

DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA

VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 2" TO 8"

VALVE ASME CLASS/RATING 150#

PIPING CLASS 011412XG

CORROSION ALLOWANCE 1.0 MM

VALVE SERVICE UTILITY AIR, NITROGEN, VENT
VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) ASTM A182 F316 + STELLITE 6

BODY SEAT RING ASTM A182 F316 + STELLITE 6

HINGE / HINGE PIN SS 316

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING DOC. NO. GF-WP3-R-SP-1001.

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 32 OF 41
DATA SHEET FOR
CHECK VALVES
VALVE CODE NUMBER : CW292FANX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 2" TO 8"

VALVE ASME CLASS/RATING 300#

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS (NOTE 3, 5)

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) 13%CR + STELLITE 6

BODY SEAT RING 13%CR + STELLITE 6

HINGE / HINGE PIN 13%CR

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 33 OF 41
DATA SHEET FOR
CHECK VALVES
VALVE CODE NUMBER : CW292GANX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 10" TO 24"

VALVE ASME CLASS/RATING 300#

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 7)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)

VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS (NOTE 3, 5)

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) CARBON STEEL + 3MM 13%CR WELD OVERLAY

BODY SEAT RING 13%CR + STELLITE 6

HINGE / HINGE PIN 13%CR

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 34 OF 41
DATA SHEET FOR
CHECK VALVES
VALVE CODE NUMBER : CW592FANX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 3" TO 8"

VALVE ASME CLASS/RATING 900#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 6)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID

VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS (NOTE 3, 5)

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) 13%CR + STELLITE 6

BODY SEAT RING 13%CR + STELLITE 6

HINGE / HINGE PIN 13%CR

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING DOC. NO. GF-WP3-R-SP-1001.

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.05 gm/lit.

6. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1
PAGE: 35 OF 41
DATA SHEET FOR
CHECK VALVES
VALVE CODE NUMBER : CW592GANX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE DUAL PLATE CHECK VALVE

VALVE SIZE RANGE 10" TO 20"

VALVE ASME CLASS/RATING 900#

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 4, 6)

VALVE SERVICE PROCESS FLUID, CLOSED DRAIN (SOUR),WELL STREAM FLUID

VALVE TO FIT BETWEEN ASME B16.5 RAISED FACE FLANGES OF SMOOTH FINISH (Ra
VALVE END CONFIGURATION
3.2 to 6.3µm)
DESIGN

VALVE DESIGN WAFER LUG TYPE DESIGN, RETAINERLESS, SPRING LOADED DISCS

VALVE INSTALLATION SHALL BE SUITABLE FOR HORIZONTAL AND VERTICAL INSTALLATION

CLOSURE MEMBER DUAL PLATES

SEAT RING RENEWABLE

TYPE OF PATTERN API 594 TYPE A

MATERIALS (NOTE 3, 5)

BODY ASTM A216 GR.WCB

DISC (DUAL PLATES) CARBON STEEL + 3MM 13%CR WELD OVERLAY

BODY SEAT RING 13%CR + STELLITE 6

HINGE / HINGE PIN 13%CR

SPRING ASTM B637 UNS N07718

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE API 594 TYPE A

FACE TO FACE DIMENSIONS API 594 TYPE A

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING DOC. NO. GF-WP3-R-SP-1001.

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED FOR
TECHNICAL REVIEW AND EVALUATION.
2. VALVES SHALL HAVE FLOW DIRECTION ARROW MARK INTEGRAL WITH BODY.

3. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

4. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
5. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-100 PPM (maximum concentration in gas phase), Max CHLORIDE-110.05 gm/lit.

6. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 13.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 26 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : DB171MLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1/2" TO 2"

VALVE ASME CLASS/RATING 150#

VALVE PORT MINIMUM BORE 14MM

PIPING CLASS 011440YG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 6 & 7)

VALVE SERVICE CLOSED & OPEN DRAINS, PROCESS WATER (SOUR)
PIPING END FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND INSTRUMENT END
VALVE END CONFIGURATION
THREADED (1/2" NPT-F) , BLEED 1/2" FLANGED RF WITH BLIND FLANGE

DESIGN

BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN

VALVE OPERATION LEVER OPERATED

BLOCK VALVES FLOATING BALL, TIGHT SHUT OFF DESIGN

BLEED VALVES ANTI TAMPER TYPE, GLOBE NEEDLE TYPE, OS&Y

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (BLOCK VALVE) NOTE 5, 8

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL MONEL

STEM / TRIM MONEL

PRIMARY SEAT RING PTFE

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3 & 4)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

MATERIALS (BLEED VALVE) NOTE 5, 8

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC MONEL + STELLITE 6

STEM / TRIM MONEL

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN / PREFORMED COMPRESSED GRAPHITE

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION
DESIGN CODE BS EN ISO 17292 (BLOCK VALVE) / ASME B16.34 (BLEED VALVE)

FACE TO FACE DIMENSIONS MANUFACTURER STANDARD

END CONFIGURATION / DIMENSIONS ASME B 16.5 (FLANGED END) / ASME B1.20.1 (THREADED END)
FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25
NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. THE DOUBLE BLOCK & BLEED ASSEMBLY SHALL HAVE THREE VALVES- PRIMARY ISOLATION, SECONDARY ISOLATION & BLEED VALVE, ALL INTEGRATED IN A FORGED SINGLE PIECE. THE HANDLES/ WRENCH POSITION
OF PRIMARY ISOLATION & SECONDARY SOLATION SHALL BE ON OPPOSITE BODY FACES. THE BLEED SHALL BE PROVIDED WITH BLIND FLANGE, GASKET AND BOLT.
3. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

4. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

5. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

6. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

7. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GFDP-CODOC. NO. GF-OGF4-J-SP-1008.
8. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 37 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : DB271HLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1/2" TO 2"

VALVE ASME CLASS/RATING 300#

VALVE PORT MINIMUM BORE 14MM

PIPING CLASS 031440XG / 031440RG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 6 & 8)

VALVE SERVICE PROCESS FLUID, PROCESS GAS, PROCESS WATER (SOUR)
PIPING END FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND INSTRUMENT END
VALVE END CONFIGURATION
THREADED (1/2" NPT-F) , BLEED 1/2" FLANGED RF WITH BLIND FLANGE

DESIGN

BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN

VALVE OPERATION LEVER OPERATED

BLOCK VALVES FLOATING BALL, TIGHT SHUT OFF DESIGN

BLEED VALVES ANTI TAMPER TYPE, GLOBE NEEDLE TYPE, OS&Y

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (BLOCK VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL 13%Cr

STEM / TRIM 13%Cr

PRIMARY SEAT RING PTFE

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3 & 4)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

MATERIALS (BLEED VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC 13%Cr + STELLITE 6

STEM / TRIM 13%Cr

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN / PREFORMED COMPRESSED GRAPHITE

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION
DESIGN CODE BS EN ISO 17292 (BLOCK VALVE) / ASME B16.34 (BLEED VALVE)

FACE TO FACE DIMENSIONS MANUFACTURER STANDARD

END CONFIGURATION / DIMENSIONS ASME B 16.5 (FLANGED END)

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008) AND PIPELINE VALVES SPECIFICATION (DOC. NO. GF-OGF4-P-SP-1001)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25
NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. THE DOUBLE BLOCK & BLEED ASSEMBLY SHALL HAVE THREE VALVES- PRIMARY ISOLATION, SECONDARY ISOLATION & BLEED VALVE, ALL INTEGRATED IN A FORGED SINGLE PIECE. THE HANDLES/ WRENCH POSITION
OF PRIMARY ISOLATION & SECONDARY SOLATION SHALL BE ON OPPOSITE BODY FACES. THE BLEED SHALL BE PROVIDED WITH BLIND FLANGE, GASKET AND BOLT.
3. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

4. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.
5. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

6. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).

7. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.
8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008 AND PIPELINE VALVES SPECIFICATION DOC. NO. GF-OGF4-P-SP-
1001.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 38 OF 41
DATA SHEET FOR
BALL VALVES
VALVE CODE NUMBER : -
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 600#

VALVE PORT MINIMUM BORE 14MM

PIPING CLASS -

CORROSION ALLOWANCE (*) 0.0 MM

VALVE SERVICE CHEMICAL INJECTION

PIPING END FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND INSTRUMENT END
VALVE END CONFIGURATION
THREADED (1/2" NPT-F) , BLEED 1/2" FLANGED RF WITH BLIND FLANGE
DESIGN
BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN
VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A182 GR.F316/316L

COVER/BONNET ASTM A182 GR.F316/316L

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PEEK

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A320-L7 / ASTM A194-7 (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)

CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292

FACE TO FACE DIMENSIONS ASME B16.10

END CONFIGURATION / DIMENSIONS ASME B 16.5

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR PAINTING AND COATING (DOC. NO. GF-OGF4-J-DS-1506)

MARKING MSS SP 25

NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.

2. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

3. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

4. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

6. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

7. VENDOR SHALL ADVICE THE SUITABILITY OF MATERIAL w.r.t. FLUID COMPOSITION.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 39 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : DB611JLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1" TO 2"

VALVE ASME CLASS/RATING 1500#

VALVE PORT MINIMUM BORE 14 MM

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 6 & 8)

VALVE SERVICE PROCESS FLUID (SOUR)
INLET / OUTLET - FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND BLEED 1/2"
VALVE END CONFIGURATION
FLANGED RF WITH BLIND FLANGE

DESIGN

BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN

VALVE OPERATION LEVER OPERATED

BLOCK VALVES FLOATING BALL, TIGHT SHUT OFF DESIGN

BLEED VALVES ANTI TAMPER TYPE, GLOBE NEEDLE TYPE, OS&Y

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (BLOCK VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL 13%Cr

STEM / TRIM 13%Cr

PRIMARY SEAT RING PEEK

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3 & 4)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
MATERIALS (BLEED VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC 13%Cr + STELLITE 6

STEM / TRIM 13%Cr

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN / PREFORMED COMPRESSED GRAPHITE

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED + FLUROCARBON

BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION
DESIGN CODE BS EN ISO 17292 (BLOCK VALVE) / ASME B16.34 (BLEED VALVE)

FACE TO FACE DIMENSIONS MANUFACTURER STANDARD

END CONFIGURATION / DIMENSIONS ASME B 16.5 (FLANGED END)

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)

MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25
NOTES:

1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. THE DOUBLE BLOCK & BLEED ASSEMBLY SHALL HAVE THREE VALVES- PRIMARY ISOLATION, SECONDARY ISOLATION & BLEED VALVE, ALL INTEGRATED IN A FORGED SINGLE PIECE. THE HANDLES/ WRENCH POSITION
OF PRIMARY ISOLATION & SECONDARY SOLATION SHALL BE ON OPPOSITE BODY FACES. THE BLEED SHALL BE PROVIDED WITH BLIND FLANGE, GASKET AND BOLT.
3. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.
4. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.
5. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.
6. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
7. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GFDP-CODOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 40 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : DB671JLNX
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1" TO 2"

VALVE ASME CLASS/RATING 1500#

VALVE PORT MINIMUM BORE 14MM

PIPING CLASS 091440XG

CORROSION ALLOWANCE (*) 6.0 MM (NOTE 6 & 8)

VALVE SERVICE Full Well Stream (SOUR), CLOSED DRAIN
PIPING END FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND INSTRUMENT
VALVE END CONFIGURATION
END THREADED (1/2" NPT-F) , BLEED 1/2" FLANGED RF WITH BLIND FLANGE

DESIGN

BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN
VALVE OPERATION LEVER OPERATED

BLOCK VALVES FLOATING BALL, TIGHT SHUT OFF DESIGN

BLEED VALVES ANTI TAMPER TYPE, GLOBE NEEDLE TYPE, OS&Y

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (BLOCK VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

BALL 13%Cr

STEM / TRIM 13%Cr

PRIMARY SEAT RING PEEK

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3 & 4)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING

ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED +

BOLTING
FLUROCARBON COATED)
MATERIALS (BLEED VALVE) NOTE 5, 7

BODY ASTM A105N

COVER/BONNET ASTM A105N

DISC 13%Cr + STELLITE 6

STEM / TRIM 13%Cr

GLAND / STEM PACKING DIAGONAL BRAIDED GRAPHITE YARN / PREFORMED COMPRESSED GRAPHITE
ASTM A193-B7M / ASTM A194-2HM (Zn Ni/CERAMIC METAL COATED +
BOLTING
FLUROCARBON COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION
DESIGN CODE BS EN ISO 17292 (BLOCK VALVE) / ASME B16.34 (BLEED VALVE)

FACE TO FACE DIMENSIONS MANUFACTURER STANDARD

END CONFIGURATION / DIMENSIONS ASME B 16.5 (FLANGED END)

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE
HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2
AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
SP-1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-

PAINTING
1001)
MARKING MSS SP 25
NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. THE DOUBLE BLOCK & BLEED ASSEMBLY SHALL HAVE THREE VALVES- PRIMARY ISOLATION, SECONDARY ISOLATION & BLEED VALVE, ALL INTEGRATED IN A FORGED SINGLE PIECE. THE HANDLES/ WRENCH
POSITION OF PRIMARY ISOLATION & SECONDARY SOLATION SHALL BE ON OPPOSITE BODY FACES. THE BLEED SHALL BE PROVIDED WITH BLIND FLANGE, GASKET AND BOLT.
3. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

4. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.

5. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.

6. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
7. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GFDP-CODOC. NO. GF-OGF4-J-SP-1008.
 EPCC OF OIL GATHERING FACILITIES (PHASE 4)

DOC. NO.: GF-WPKF-J-DS-1506

REVISION: 1

PAGE: 41 OF 41
DATA SHEET FOR
DBB VALVES
VALVE CODE NUMBER : DB6757L
DESCRIPTION SPECIFICATION REQUIREMENT VENDOR'S CONFIRMATION
GENERAL DATA
VALVE TYPE INTERGAL TYPE DOUBLE BLOCK AND BLEED VALVE

VALVE SIZE RANGE 1/2" TO 1 1/2"

VALVE ASME CLASS/RATING 1500#

VALVE PORT REDUCED BORE

PIPING CLASS 153411XG

CORROSION ALLOWANCE (*) 0.0 MM

VALVE SERVICE CHEMICAL INJECTION

PIPING END FLANGED (RF) , SMOOTH FINISH (Ra=3.2 to 6.3µm) AND INSTRUMENT END
VALVE END CONFIGURATION
THREADED (1/2" NPT-F) , BLEED 1/2" FLANGED RF WITH BLIND FLANGE

DESIGN
BALL VALVE FOR PRIMARY AND SECONDARY ISOLATION (BLOCK) AND 1/2" GLOBE
VALVE DESIGN
NEEDLE TYPE VALVE FOR BLEED, ANTI STATIC, FIRESAFE DESIGN
VALVE OPERATION LEVER OPERATED

BALL SUPPORT FLOATING BALL

STEM ANTI BLOW OUT TYPE (NO CASTING)

STEM SEAL RENEWABLE

MATERIALS (NOTE 4, 6)

BODY ASTM A182 GR.F316/316L

COVER/BONNET ASTM A182 GR.F316/316L

BALL ASTM A182 F316

STEM / TRIM ASTM A182 F316

PRIMARY SEAT RING PEEK

PRIMARY / SECONDARY SEALS VITON B / GRAPHITE (NOTE 3)

GASKET SPIRAL WOUND GASKET, AISI 316L, GRAPHITE, CS CENTERING / SS INNER RING
ASTM A320-L7 / ASTM A194-7 (Zn Ni/CERAMIC METAL COATED + FLUROCARBON
BOLTING
COATED)
CODES AND STANDARDS / TESTING / CERTIFICATION

DESIGN CODE BS EN ISO 17292 (BLOCK VALVE) / ASME B16.34 (BLEED VALVE)

FACE TO FACE DIMENSIONS MANUFACTURER STANDARD

END CONFIGURATION / DIMENSIONS ASME B 16.5 (FLANGED END)

FIRE SAFE API 6FA / API 607 /BS EN ISO 10497 AS APPLICABLE

HYDROSTATIC TEST & AIR TEST API 598 / BS EN 12266 - 1 & 2

AS PER MATERIAL SPECIFICATION FOR PIPING AND VALVES (DOC. NO. GF-OGF4-J-SP-
NDT (MPI/DP/RADIOGRAPHY/ UT ETC.)
1008)
MATERIAL CERTIFICATION BS EN 10204 TYPE 3.1 FOR PRESSURE CONTAINING PARTS & 2.2 FOR OTHER PARTS

PAINTING AS PER SPECIFICATION FOR COATING AND PAINTING (DOC.NO. GF-OGF4-R-SP-1001)

MARKING MSS SP 25

NOTES:
1. THIS DATA SHEET SHALL BE COMPLETELY FILLED BY THE VENDOR, STAMPED, SIGNED AND DEVIATIONS CLEARLY MARKED FOR ACCEPTANCE. QUOTATION WITHOUT THIS DATA SHEET WILL NOT BE CONSIDERED
FOR TECHNICAL REVIEW AND EVALUATION.
2. THE DOUBLE BLOCK & BLEED ASSEMBLY SHALL HAVE THREE VALVES- PRIMARY ISOLATION, SECONDARY ISOLATION & BLEED VALVE, ALL INTEGRATED IN A FORGED SINGLE PIECE. THE HANDLES/ WRENCH POSITION
OF PRIMARY ISOLATION & SECONDARY SOLATION SHALL BE ON OPPOSITE BODY FACES. THE BLEED SHALL BE PROVIDED WITH BLIND FLANGE, GASKET AND BOLT.

3. GRAPHITE BASED PACKING SHALL CONTAIN CORROSION INHIBITOR TO PREVENT OXIDATION OF THE STEM.

4. ELASTOMERIC SEALS SHALL BE ANTI-EXPLOSIVE DECOMPRESSION (AED) TYPE AND SHALL BE SUITABLE FOR SERVICE AND DESIGN CONDITIONS.
5. ALL MATERIALS SHALL BE SUITABLE FOR USE IN SOUR ENVIRONMENT AND CERTIFIED TO NACE MR0175/ISO 15156 LATEST EDITION.
6. VENDOR SHALL CONFIRM THAT THE CORROSION ALLOWANCE IS INCLUDED IN THICKNESS CALCULATION OF CARBON STEEL PARTS (IN CONTACT WITH FLUID).
7. VENDOR TO CONFIRM ALL WETTED PARTS ARE SUITABLE FOR PROCESS FLUID AND FOULING MATERIALS AS FOLLOWS:
Max CO2-1 Mol%, Max H2S-200 PPM (maximum concentration in gas phase), Max CHLORIDE-103.7 gm/lit.

8. (*) DENOTES SPECIAL REQUIREMENT AS DEFINED IN SECTION 16.1 OF MATERIAL SPECIFICATION FOR PIPING AND VALVES DOC. NO. GFDP-CODOC. NO. GF-OGF4-J-SP-1008.