Bảng thông số sản phẩm

Thông số kỹ thuật

variable speed drive ATV310, 4 kW,

5.5 hp, 380...460 V, 3 phase, without
filter
ATV310HU40N4E

Miễn trừ trách nhiệm: Tài liệu này không nhằm thay thế và không được sử dụng để xác định tính phù hợp hoặc độ tin cậy của các sản phẩm này cho các ứng dụng người dùng cụ thể
Main
Range of product Easy Altivar 310

Product or component type Variable speed drive

Product specific application Simple machine

Assembly style With heat sink

Device short name ATV310

Network number of phases Three phase

[Us] rated supply voltage 380...460 V - 15...10 %

Motor power kW 4 kW

Motor power hp 5.5 hp

Noise level 50 dB

Complementary
Product destination Asynchronous motors

Quantity per set Set of 1

EMC filter Without EMC filter

Type of cooling Integrated fan

Supply frequency 50/60 Hz +/- 5 %

Communication port protocol Modbus

Connector type RJ45 (on front face) for Modbus

Physical interface 2-wire RS 485 for Modbus

Transmission frame RTU for Modbus

Transmission rate 4800 bit/s

9600 bit/s
19200 bit/s
38400 bit/s

Number of addresses 1…247 for Modbus

Communication service Read holding registers (03) 29 words

Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)

Line current 11.4 A

Apparent power 9.1 kVA

08-02-2023 1
Prospective line Isc 5 kA

Continuous output current 9.5 A at 4 kHz

Maximum transient current 14.3 A for 60 s

Power dissipation in W 102.72 W at In

Speed drive output frequency 0.5…400 Hz

Nominal switching frequency 4 kHz

Switching frequency 2...12 kHz adjustable

Speed range 1…20

Transient overtorque 170…200 % of nominal motor torque depending on drive rating and type of motor

Braking torque Up to 150 % of nominal motor torque with braking resistor at high inertia
Up to 70 % of nominal motor torque without braking resistor

Asynchronous motor control Quadratic voltage/frequency ratio

profile Energy saving ratio
Sensorless flux vector control

Motor slip compensation Adjustable

Adjustable

Output voltage 380...460 V three phase

Electrical connection Terminal, clamping capacity: 2.5...4 mm² (L1, L2, L3, PA/+, PB, U, V, W)

Tightening torque 1.2…1.4 N.m

Insulation Electrical between power and control

Supply Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC, <10 mA with overload and short-
circuit protection
Internal supply for logic inputs: 24 V (20.4…28.8 V)DC, <100 mA with overload and short-circuit
protection

Analogue input number 1

Analogue input type Configurable current AI1 0...20 mA 250 Ohm

Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm

Discrete input number 4

Discrete input type Programmable LI1...LI4 24 V 18...30 V

Discrete input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)

Sampling duration 10 ms for analogue input

20 ms, tolerance +/- 1 ms for logic input

Linearity error +/- 0.3 % of maximum value for analogue input

Analogue output number 1

Analogue output type AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits

Discrete output number 2

Discrete output type Logic output LO+, LO-

Protected relay output R1A, R1B, R1C 1 C/O

Minimum switching current 5 mA at 24 V DC for logic relay

Maximum switching current 2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay
3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay
4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay

Acceleration and deceleration Linear from 0...999.9 s

ramps S
Linear from 0...999.9 s

Braking to standstill By DC injection, <30 s

Protection type Line supply overvoltage

Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase

2
08-02-2023
 Thermal motor protection via the drive by continuous calculation of I²t

Frequency resolution Analog input: converter A/D, 10 bits

Display unit: 0.1 Hz

Time constant 20 ms +/- 1 ms for reference change

Operating position Vertical +/- 10 degree

Height 184 mm

Width 140 mm

Depth 151 mm

Net weight 1.8 kg

Environment
Electromagnetic compatibility Electrical fast transient/burst immunity test - test level: level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test - test level: level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances - test level: level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test - test level: level 3 conforming to EN/IEC
61000-4-3
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
Surge immunity test - test level: level 3 conforming to EN/IEC 61000-4-5

Standards EN/IEC 61800-5-1

EN/IEC 61800-3

IP degree of protection IP20 without blanking plate on upper part

IP40 top

Pollution degree 2 conforming to EN/IEC 61800-5-1

Environmental characteristic Dust pollution resistance class 3S2 conforming to EN/IEC 60721-3-3
Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3

Shock resistance 15 gn conforming to EN/IEC 60068-2-27 for 11 ms

Relative humidity 5…95 % without condensation conforming to IEC 60068-2-3

5…95 % without dripping water conforming to IEC 60068-2-3

Ambient air temperature for -25…70 °C

storage

Ambient air temperature for -10…55 °C without derating

operation 55…60 °C protective cover from the top of the drive removed with current derating 2.2 % per °C

Operating altitude <= 1000 m without derating

Packing Units
Unit Type of Package 1 PCE

Number of Units in Package 1 1

Package 1 Height 18.8 cm

Package 1 Width 18.29 cm

Package 1 Length 23.11 cm

Package 1 Weight 2.16 kg

Unit Type of Package 2 S03

Number of Units in Package 2 2

Package 2 Height 30 cm

Package 2 Width 30 cm

Package 2 Length 40 cm

Package 2 Weight 4.981 kg

Offer Sustainability
Sustainable offer status Green Premium product

REACh Regulation REACh Declaration

08-02-2023 3
EU RoHS Directive Compliant
EU RoHS Declaration

Mercury free Yes

China RoHS Regulation China RoHS declaration

RoHS exemption information Yes

Environmental Disclosure Product Environmental Profile

Circularity Profile End of Life Information

WEEE The product must be disposed on European Union markets following specific waste collection and
never end up in rubbish bins

4
08-02-2023
Bảng thông số sản phẩm ATV310HU40N4E
Dimensions Drawings

Dimensions

Dimensions in mm

a b c G H H1 Ø For screws

140 171 151 126 157 184 5 M4

Dimensions in in.

a b c G H H1 Ø For screws

5.51 6.73 5.94 4.96 6.18 7.24 0.20 M4

08-02-2023 5
Bảng thông số sản phẩm ATV310HU40N4E
Mounting and Clearance

Mounting Recommendations

Clearance

Mounting Types
Mounting Type A

Mounting Type B

Remove the protective cover from the top of the drive.

6
08-02-2023
Bảng thông số sản phẩm ATV310HU40N4E
Connections and Schema

Three-Phase Power Supply Wiring Diagram

A1 : Drive
KM1 : Contactor (only if a control circuit is needed)
P1 : 2.2 kΩ reference potentiometer. This can be replaced by a 10 kΩ potentiometer (maximum).
Q1 : Circuit breaker
R : Braking resistor (optional)
(1) Negative logic (Sink)
(2) Positive logic (Source) (factory set configuration)
(3) 0...10 V or 0...20 mA
(4) Line choke three-phase (optional)

Thay thế được đề xuất

08-02-2023 7