Department of Education
NATIONAL CAPITAL REGION
SUPPLEMENTARY
LEARNING MATERIALS
for Junior High School
Learners
TECHNOLOGY AND LIVELIHOOD EDUCATION
GRADE 9
ICT-COMPUTER SYSTEMS SERVICING NC II
(Module 7)
LEARNING COMPETENCY:
LO 2. Terminate/connect electrical wiring electronics circuits.
TLE_IACSS9-12TCEW-IIIg-i-22
1
HOW TO USE THIS SUPPLEMENTARY LEARNING
MATERIALS
Before you start answering the module, I want you to set aside other
tasks that will disturb you while enjoying the lessons. Read the simple
instructions below to successfully enjoy the objectives of this kit. Have fun!
1. Follow carefully all the contents and instructions indicated in every
page of this module.
2. Write on your notebook or any writing pad the concepts about the
lessons. Writing enhances learning, that is important to develop
and keep in mind.
3. Perform all the provided activities in the module.
4. Let your facilitator/guardian assess your answers.
5. Analyze conceptually the posttest and apply what you have learned.
6. Enjoy studying!
TERMINATING AND CONNECTING ELECTRICAL WIRING
AND ELECTRONICS CIRCUIT (TCEW)
EXPECTATIONS
At the end of the module, you should be able to:
1. observe safety procedure in using tools for network cabling;
2. use appropriate range of methods in termination/connection in accordance with
specifications, manufacturer’s requirements, and safety;
3. follow the correct sequence of network cabling:
2
PRETEST
Directions: Name the correct sequence of color-coding using crossover network cable.
Side A (T-568A) Side B (T-568B)
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
LOOKING BACK
Directions: Calculate the tolerance and convert the color of the following resistor.
1. Red, Brown, Orange, Silver (4 points)
2. Yellow, Green, Black, Gold (4 points)
3. 3270 ohms ± 20% (2 points)
BRIEF INTRODUCTION
This module covers the knowledge and understanding on the mastery of
terminating wires - Network Cabling (Straight - Through and Crossover Network Cables)
in Computer Systems Servicing. It contains learning activities on Computer Systems
Servicing for you to accomplish.
3
T-568A Straight-Through Ethernet Cable
SEQUENCE OF COLORS
1. White Green (Stripe)
2. Green
3. White Orange (Stripe)
4. Blue
5. White Blue (Stripe)
6. Orange
7. White Brown (Stripe)
8. Brown
T-568A Straight-Through Ethernet Cable
SEQUENCE OF COLORS
1. White Orange (Stripe)
2. Orange
3. White Green (Stripe)
4. Blue
5. White Blue (Stripe)
6. Green
7. White Brown (Stripe)
8. Brown
4
Crossover Ethernet Cable
SEQUENCE OF COLORS
Side 1 is T-568A Straight-
Through Ethernet Cable
Side 2 is T-568B Straight-
Through Ethernet Cable
STEPS IN CREATING T-568A STRAIGHT THROUGH ETHERNET CABLE
1. Crimping Tool
2. RJ45
Step 1. Prepare all the tools and materials needed.
3. Wire Stripper
4. Ethernet Cable
Step 2. Determine the length of the cable needed.
Step 3. Carefully strip the cable using the wire stripper.
Step 4. Untwist and pull the wires to straighten them.
Step 5. Arrange the wires based on T568A wiring.
5
Step 6. Trim the wires to a suitable length.
Step 7. Insert the wires all the way into the RJ-45
connector.
Step 8. Inspects the cable from its side and from the top.
Step 9. Insert the wired connector to the RJ-45 crimper
and crimp it.
Step 10. Repeat the steps 3-9 on the other end of the
cable.
Step 11. Test the Cable.
6
ACTIVITIES
Directions: In a short bond paper, draw and color the CROSSOVER NETWORK
CABLE.
Materials: 1. Bond paper
2. Pencil
3. Coloring materials
Here is the scoring rubric for your work accomplished.
Criteria Points Score
Preciseness 5
Creativity 5
Neatness 5
Total 15
REMEMBER
Occupational Health and Safety (OHS)
• Be careful with tools.
• Do not use excessive force if things do not quite slip into place.
• Clean the area before and after using it to maintain sanitation and prevent
accidents.
• Make sure that the pins are properly aligned.
7
CHECKING YOUR UNDERSTANDING
Directions. Arrange the following steps in network cabling. Use number 1 – 10 for
sequencing and write your answer under the Step No. column.
Steps / Procedures Step No.
Test the Cable.
Determine the length of the cable needed.
Insert the wires all the way into the RJ-45 connector.
Arrange the wires based on T568A wiring.
Insert the wired connector to the RJ-45 crimper and crimp it.
Untwist and pull the wires to straighten them.
Inspects the cable from its side and from the top.
Prepare all the tools and materials needed.
Repeat the steps 3-9 on the other end of the cable.
Carefully strip the cable using the wire stripper.
POST TEST
Directions: Name the correct sequence of color-coding using crossover network cable.
Side A (T-568A) Side B (T-568B)
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
8
ANSWER KEY
10. STEP 3
8. BROWN 8. BROWN 9. STEP 10
7. WHITE BROWN (STRIPE) 7. WHITE BROWN (STRIPE) 8. STEP 1
6. GREEN 6. ORANGE 7. STEP 8
5. WHITE BLUE (STRIPE) 5. WHITE BLUE (STRIPE)
6. STEP 4
4. BLUE 4. BLUE
3. WHITE GREEN (STRIPE) 3. WHITE ORANGE (STRIPE) 5. STEP 9
BROWN, NO COLOR
2. ORANGE 2. GREEN 4. STEP 5
3. ORANGE, RED, VIOLET,
1. WHITE ORANGE (STRIPE) 1. WHITE GREEN (STRIPE) 3. STEP 7
2. 45 OHMS ± 5%
2. STEP 2
SIDE B (T-568B) SIDE A (T-568A) 1. 21000 OHMS ± 10% 1. STEP 11
PRE-TEST AND POST-TEST LOOKING BACK CHECK YOUR UNDERSTANDING
REFERENCES
Navarro, R. T., Jr. (2019). Network Cabling [PPT]. Parañaque City: Navarro.
Prepared by:
NAME OF WRITER: RENE D. BERNABE
Position: Teacher I
School: Muntinlupa Business High School- Sucat Annex
Schools Division Office: Muntinlupa City
NAME OF VALIDATOR: GREGORIO S. QUINERI
Position: Teacher III
School: Muntinlupa Business High School - Main
Schools Division Office: Muntinlupa City
NAME OF LANGUAGE EDITOR: DR. VALENTINA A. BALLESTEROS
Position: Education Program Supervisor
Schools Division Office: Muntinlupa City
