282, 11:46 PM Moodle NIT Rourkela Continuous Evaluation Quiz 1 CE6234 Prestressed Concrete (Spring 2021-22) Horne ® My courses ® Civil Engineering ® Theory Courses ® CE6234-PresCon-Spr21-22 ® Topic 9 > Continuous Evaluation Quiz 1 Show one page atatime Correct Mark 1.50 out of 1.50 Finish review Flag question Question 2 Correct Mark 1.50 out of 1.80 F Flag question hitps:moadle.nithl.ac.invmodiquizreviow php?attompt=19825&showall=1 igation Started on Thursday, 17 February 2022, 3:36 PM State Finished EI Completed on Thursday, 17 February 2022, 10:35 PM 7I\[8 Time taken 6 hours 58 mins — Grade 27.00 out of 30.00 (90%) 3) 4 19) Question 1 A pretensioned member of cross-section width b= 330 mm and height h= 510 mm is prestressed with steel of Aps= 505 mm? at center of gravity of section, stressed to a level of 0°,=1050 N/mm2. Assuming m= 7, compute compressive stress in concrete just after transfer. Express the magnitude of this stress in MPa correct to 3 decimal places. Answer: [5.095 Vv A pretensioned member of cross-section width b= 330 mm and height h= 510 mm is prestressed with steel of Aps= 505 mm? at center of gravity of section, stressed to a level of 0°,=1050 N/mm2, Assuming m= 1a2812, 1:46 PM Question 3 correct Mark 150 out of 1.50 WF Flag question Question 4 correct Mark 1.50 out of 1.50 WF Hag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 4 7, compute tensile stress in steel just after transfer. Express the magnitude of this stress in MPa correct to 3 decimal places. Answer: [f031431 J A pretensioned member has of cross-section width b= 390 mm and height h= 490 mm and is 6 m long. It is prestressed with Aps= 510 mm? of high tensile steel at 150 mm above the bottom fibre. The steel is stressed to a level of 0°,=1020 N/mm2. Assume m= 6. Compute the stress in concrete just after transfer in the top fiber. Compressive stress is reported with positive sign and tensile stress is reported with negative sign correct to 3 decimal places. Units: Mpa. (Use the approach discussed in lecture ay Answer: [0236 lv A pretensioned member has of cross-section width b= 390 mm and height h= 490 mm and is 6 m long. It is prestressed with Aps= 510 mm? of high tensile steel at 150 mm above the bottom fibre. The steel is stressed to a level of 09,=1020 N/mm2, Assume m= 6. Compute the stress in concrete just after transfer in the bottom fiber. Compressive stress is reported with positive sign and tensile stress is reported with negative sign correct to 3 decimal places.2812, 1:46 PM Question 5 correct Mark 1.50 out of 1.50 WF Hag question Question 6 correct Mark 1.50 out of 1.50 F Flag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 1 Units: Mpa. (Use the approach discussed in lecture ay Answer: [5.777 lv Apretensioned member has of cross-section width b= 390 mm and height h= 490 mm and is 6 m long. It is prestressed with Aps= 510 mm? of high tensile steel at 150 mm above the bottom fibre. The steel is stressed to a level of 0°,=1020 N/mmZ2. Assume m= 6. Compute the stress in concrete just after transfer at the level of steel. Compressive stress is reported with positive sign and tensile stress is reported with negative sign correct to 3 decimal places. Units: Mpa. (Use the approach discussed in lecture ay Answer: 875 lV A pretensioned member has of cross-section width b= 390 mm and height h= 490 mm and is 6 m long. It is prestressed with Aps= 510 mm? of high tensile steel at 150 mm above the bottom fibre. The steel is stressed to a level of 0°,=1020 N/mm2. Assume m= 6. Compute the magnitude of the final stress in steel. Express the magnitude in Mpa correct to 3 decimal places. (Use the approach discussed in lecture 4.) Answer: [996.7502812, 1:46 PM Question 7 correct, Mark 1.00 out of 1.00 WF Flag question Question 8 correct Mark 2.00 out of 2.00 1 Hag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 4 A post tensioned concrete beam 270mm wide and 370 mm dee spanning over 10 m is stresset by successive tensioning and anchoring of two cables 1 and 2 respectively. The cross-sectional area of each duct is 1050 mm?. The cross-sectional area of each cable is 100mmZ2and the initial stress in the cable is 0°=1050 N/mm2, m= 6. Cable 1 has straight sloping profile with an eccentricity e1 =111.0 mm below the centroidal axis at the center of span and zero eccentricity at the support sections. Cable 2 also has straight sloping profile with zero eccentricity at the center span and an eccentricity e2=92.5mm at the end of the span. Use net section properties for post-tensioned members. Determine the net area at mid- section. Express your answer in mm?. Round off to 3 decimal places. ‘Answer: [B7800,000 A post tensioned concrete beam 270mm wide and 370 mm dee; spanning over 10 mis stresse by successive tensioning and anchoring of two cables 1 and 2 respectively. The cross-sectional2812, 1:46 PM Question 9 Mark 0,00 out of 3.00 WF Flag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 1 area of each duct is 1050 mm2. The cross-sectional area of each cable is 100mmZ2and the initial stress in the cable is 0°=1050 N/mm2, m= 6. Cable 1 has straight sloping profile with an eccentricity e1 =111.0 mm below the centroidal axis at the center of span and zero eccentricity at the support sections. Cable 2 also has straight sloping profile with zero eccentricity at the center span and an eccentricity e2=92.5mm at the end of the span. Use net section properties for post-tensioned members. Determine the moment of inertia at the mid-section. Express your answer in mm4, Round off to 1 decimal place. ‘Answer: [1126616627.0 JY A post tensioned concrete beam 270mm wide and 370 mm deey spanning over 10 mis stresse by successive tensioning and anchoring of two cables 1 and 2 respectively. The cross-sectional area of each duct is 1050 mm2. The cross-sectional area of each cable is 100mm2and the initial stress in the cable is °=1050 N/mm, m= 6. Cable 1 has straight sloping profile with an eccentricity e1 =111.0 mm below2812, 1:46 PM Question 10 Correct Mark 1.00 out of 1.00 1 Flag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 1 the centroidal axis at the center of span and zero eccentricity at the support sections. Cable 2 also has straight sloping profile with zero eccentricity at the center span and an eccentricity e2=92.5mm at the end of the span. Use net section properties for post-tensioned members. Assume the moment of inertia and centroidal location of the net area at any cross-section to be equal to that calculated at the mid-section. Estimate the total loss of pre- stress force in the cables due to elastic shortening, if they are successively tensioned (cable 1 followed by cable 2) and anchored. (Express your answer in newton. Round off to 3 decimal places). Cable 2 Answer: [24.490 Ix Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) ortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress2812, 1:46 PM Question 11 correct Mark 1,00 out of 1.00 | Hag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 4 force of 290KN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs. Sketch the force flow diagram. Evaluate the prestress force at C. (Express your answer in newton. Round off to 0 decimal places). ba Answer: 74251 lv Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) ortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress force of 290kKN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs. Sketch the force flow diagram. Evaluate the prestress force at B. (Express your answer in newton. Round off to 0 decimal places). m32812, 1:46 PM Question 12 correct Mark 2,00 out of 2.00 F Hag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 4 P. AY | & coon CB: Straight Answer: [274251 Vv Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) ortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress force of 290kN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs, An anchorage slip of 0.5 mm occurs. The coefficient of return friction y'=1.5p1, Aps= 520mm?. Es= 191GPa. Evaluate the prestress force at A. (Express your answer in newton. Round off to 0 decimal places). ba Answer: 22719482812, 1:46 PM Question 13, correct Mark 1,00 out of 1.00 WF Hag question Question 14 Correct Mark 2.00 out of 2.00 WF Flag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz 4 Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) ortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress force of 290kN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs, An anchorage slip of 0.5 mm occurs. The coefficient of return friction y'=1.5p1, Aps= 520mm?. Es= 191GPa. Evaluate the prestress force at C. (Express your answer in newton. Round off to 0 decimal places), ba x coon CB: Straight Answer: [282779 lV Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) jortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with2812, 1:46 PM Question 15) correct Mark 1.00 out of 1.00 WF Hag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Continuous Evaluation Quiz + respect to gross centroid of section of span 12m. Prestress force of 290KN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs. An anchorage slip of 1.2 mm occurs. The coefficient of return friction p’=1.5p1, Aps= 520mm2. Es= 191GPa. Evaluate the prestress force at A. (Express your answer in newton. Round off to 0 decimal places). ba Answer: [262034 lv Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) ortion and straight ine(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress force of 290kN is applied from one end A. The loss In prestressing force due to friction = 0.5(Neglect wobble effect) occurs. An anchorage slip of 1.2 mm occurs. The coefficient of return son2812, 1:46 PM Question 16 Correct Mark 1.00 out of 1.00 WF Flag question htpssmoocle. ntl. infmodiquizreviow php attempt=9825&showallt Coninvos Evaution uz 4 friction y'=1.5p1, Aps= 520mm?. Es= 191GPa, Evaluate the prestress force at C. (Express your answer in newton. Round off to 0 decimal places). Answer: p7aa14 Vv Post-tensioned prestressed concrete beam has a cable consisting of parabolic(AC) portion and straight line(CB)portion. C lies on the mid-span section and the slope of the cable is continuous at C. The eccentricity e= 280mm with respect to gross centroid of section of span 12m. Prestress force of 290kN is applied from one end A. The loss in prestressing force due to friction y= 0.5(Neglect wobble effect) occurs. An anchorage slip of 1.2 mm occurs. The coefficient of return friction y'=1.5p1, Aps= 520mm?. Es= 191GPa. Evaluate the prestress force at B. (Express your answer in newton. Round off to 0 decimal places), na282, 11:46 PM Question 17 correct Mark 2,00 out of 2.00 F Hag question Question 18. correct Mark 2,00 out of 2.00 YF Hag question hitps:moadle.nithl.ac.invmodiquizreviow php?attompt=19825&showall=1 Continuous Evaluation Quiz 4 NA CB: Straight \CA: Parabola C Answer: [274251 lV Acconcrete beam prestressed by a cable with initial stress 1050N/mm?, The characteristic strength of concrete fck = 60 MPa. The beam is located in an area having a relative humidity of 70 percent. The beam is exposed to environment on bottom face and two side faces. The depth of beam is 450 mm and width is 340 mm. The beam is cured for 21 days before itis prestressed. At time 50 days: Determine the autogenous shrinkage strain. Express the answer in microns.(For example, if the strain is 0.00006245, which is 62.45 microns: type the answer as 62.45). Answer: [77.50 lv A concrete beam prestressed by a cable with initial stress 1050N/mm2. The characteristic strength of concrete fck = 60 MPa. The beam is located in an area having a relative humidity of 70, percent. The beam is exposed to environment on bottom face and two side faces. The depth of beam is 450 mm and width is 340 mm. The beam is cured for 21 days before itis prestressed. At time 50 days: Determine the drying shrinkage strain. Express the answer in microns.(Forexample, ifthe strain is 0,00006245, which is 62.45 microns: type the answer as 62.45). Answer: 84.77 Vv ra3282, 11:46 PM Question 19 correct Mark 2.00 out of 2.00 F Flag question htpssmoasle.nitkl.ac.infmodiquizreviow php?attempt=19825&show Continuous Evaluation Quiz 1 A concrete beam prestressed by a cable with initial stress 1050N/mm?, The characteristic strength of concrete fck = 60 MPa. The beam is located in an area having a relative humidity of 70 percent. The beam Is exposed to environment on bottom face and two side faces. The depth of beam is 450 mm and width is 340 mm. The beam is cured for 21 days before itis prestressed. At time 50 days: Determine the magnitude of loss of prestress due to shrinkage. (Youngs modulus of steel =2.1x 1095 MPa.) Express the answer in MPa rounding off to 2 decimal places. Answer: 22.40 lv Finish review ‘thoodle sa