SIPROTEC 5 SIPROTEC 5

Product information Product information

Disclaimer of Liability Conditions of UL Listing Current Terminals

Subject to changes and errors. The information given in this document only contains WARNING Servicing of the circuitry involving the batteries and replacement of the lithium batteries
Wire cross-section 2x AWG 14-10 (2.0 mm2 to 4.0 mm2) solid
general descriptions and/or performance features which may not always specifically Danger of death, personal injury or substantial property damage shall be done by a trained technician.
or
reflect those described, or which may undergo modification in the course of further Replace battery with Varta or Panasonic CR 2032 or BR 2032 type batteries only. Use
Non-observance of the following measures can result in death, 2x AWG 12-10 (2.6 mm2 to 5.2 mm2)
development of the products. of another Battery may present a risk of fire or explosion. See Hardware manual for
personal injury or substantial property damage. stranded with UL-listed Ring Cable Lug, for
The requested performance features are binding only when they are expressly agreed safety instructions. example, PIDG by Tyco
 The equipment must be grounded at the grounding terminal before
upon in the concluded contract. Field wires of control circuits shall be separated from other circuits with respect to the Use copper conductors only, at least certified
any connections are made. This is also valid for the connections
end use requirements. for a temperature of +105 °C
Copyright between base and expansion modules. The conductor cross-
Use prepared solid conductors intended for
Copyright © Siemens 2019 – All Rights Reserved section must be at least AWG 10 (4 mm²). The tightening torque Type 1 if mounted into a door or front cover of an enclosure.
single or multi-wiring connection, maximum 2
for the M4 grounding screw must be at least 1.2 Nm. When expanding the device with the 2nd device row, then they must be mounted
The reproduction, transmission or use of this document or its contents is not permitted wires per pole, and for usage of ferrules,
completely inside an enclosure.
without express written authority. Offenders will be liable for damages. All rights,  All circuit components connected to the power supply may be crimped-on pressure wire connectors (ring-
including rights created by patent grant or registration of a utility model or design, are subject to hazardous voltages. Temporarily permissible surrounding air temperature tsurr: max. 70 °C (158 °F), type and pin-type).
reserved.  Hazardous voltages may be present in equipment even after the Load conditions for the non-modular devices:
Ring Cable Lug with plastic sleeve L = 10 mm (0.39 in) to L = 12 mm (0.47 in)
supply voltage has been disconnected (capacitors can still be With surrounding air temperatures above 55 °C, no more than 50 % of the binary
Trademarks inputs and relay outputs per assembly are allowed to be continuously active. Stripping length (when used without 15 mm (0.59 in); only solid copper wires may
charged).
SIPROTEC™, DIGSI™, SIGRA™, SIGUARD™, SAFIR™, SICAM™, and Ring Cable Lug) be used.
MindSphere™ are trademarks of Siemens AG. Any unauthorized use is prohibited. All  The power-supply unit has an internal fuse which cannot be Binary input voltage DC: Urated 250 V max.
other designa- tions in this document may represent trademarks whose use by third changed. Max. rated data of the output contacts in accordance with UL certification:
parties for their own purposes may violate the proprietary rights of the owner.  Equipment with exposed current-transformer circuits must not be D (for bolt): 5.0 mm (0.20 in)
Standard Relay (Type S) DC 24 V, 5 A, General Purpose

W
D
operated. Before disconnecting the equipment, ensure that the W: 9.5 mm (0.37 in)
DC 48 V, 0.8 A, General Purpose
NOTE current-transformer circuits are short-circuited. L: 7.1 mm (0.28 in) to 7.7 mm (0.30 in)
DC 240 V, 0.1 A, General Purpose
 The limit values stated under “Technical Data” in the SIPROTEC 5 AC 240 V, 5 A, General Purpose L
Assembly Dimensions, Installation, Terminal and Connection Diagrams
and Technical Data are part of the SIPROTEC 5 Hardware Manual. Hardware manual may not be exceeded. This must also be AC 120 V, 1/6 hp
considered during testing and commissioning. AC 250 V, 1/2 hp
The manuals are available in the SIPROTEC Download Area on the B300 Permissible tightening torque at the 2.7 Nm (23.9 lb.in.)
Internet (http://www.siemens.com/siprotec). If you require further information, or if particular problems occur that are not handled in R300 terminal screw
sufficient depth in the instructions of the respective product, you can request help
Fast Relay (Type F) AC 120 V, 5 A, General Purpose Maximum allowed speed of the used 640 RPM
Notes on Safety through your local Siemens Office or representative.
tool
AC 250 V, 5 A, General Purpose
This manual contains notes that must be adhered to for your own personal safety and
AC 250 V, 0.5 hp Location on device To be visible as follows:
to avoid damage to property. WARNING
B300
However, it does not constitute a complete description of all safety measures required Laser radiation! Danger of eye injury R300
for installation, service, and maintenance of the equipment (module, device) in
This device may contain a class 1 laser. High-Speed Relay with Semi- B150
question. Details are to be taken from the manuals and those are mandatory.
conductor Acceleration (Type HS) Q300
 Do not look directly into the beam.
WARNING Power Relay (for Direct Control of DC 300 V, 4.5 A - 30 s ON, 15 min OFF
Motor Switches) DC 250 V, 1 Hp Motor - 30 s ON,
Danger of severe personal injury or substantial damage to 15 min OFF
property CAUTION
DC 110 V, 3/4 Hp Motor - 30 s ON,
Hazardous voltages may occur in devices and modules during Danger of damage due to static electrical charges 15 min OFF
operation depending on the design and application. DC 60 V, 10 A, 1/2 Hp Motor - 30 s ON,
The printed circuit boards of numerical relays contain CMOS circuits.
 Always observe the instructions given in “Qualified Electrical 15 min OFF
These shall not be withdrawn or inserted under live conditions! The
Engineering Personnel” below. DC 48 V, 10 A, 1/3 Hp Motor - 30 s ON,
modules must be so handled that any possibility of damage due to
15 min OFF
static electrical charges is excluded.
Qualified Electrical Engineering Personnel DC 24 V, 10 A, 1/6 Hp Motor - 30 s ON,
 During any necessary handling of individual modules the 15 min OFF
Only qualified electrical engineering personnel may commission and operate the recommendations relating to the handling of electrostatically
equipment (module, device) described in this document. Qualified electrical endangered components (EEC) must be observed.
engineering personnel in the sense of this document are people who can demonstrate CAUTION
technical qualifications as electrical technicians. These persons may commission,  In installed conditions, the modules are in no danger.
Danger of fire or chemical burn hazard
isolate, ground and label devices, systems and circuits according to the standards of
safety engineering. Statement of Conformity The battery used in this device may present a fire or chemical burn
Low-voltage Directive 2014/35/EU hazard if mistreated.
Use as Prescribed
EMC Directive 2014/30/EU  Do not recharge, disassemble, heat above 100 °C (212 °F) or
The equipment (device, module) may only be used for such applications as set out in Voltage Terminals, Binary Inputs and Outputs
incinerate.
the catalogs and the technical description, and only in combination with third-party This conformity is based on the compliance with the following Wire cross-section 1x AWG 20-14 (0.5 mm2 to 2.5 mm2) solid
equipment recommended and approved by Siemens. harmonized standards:  Dispose the used battery promptly. or stranded with or without UL-listed ferrule
Problem-free and safe operation of the product depends on the following: EN 60255-26 and EN 60255-27  Keep away from children! Use AWG 14 (2.5 mm²) for currents from 5 A
to 10 A.
• Proper transport Use copper conductors only, at least certified
Other Standards
• Proper storage, setup, and installation IEEE Std C 37.90 for a temperature of +105 °C
• Proper operation and maintenance The technical data of the product is approved in accordance with UL. Ferrule with plastic sleeve L = 12 mm (0.47 in)
For more information about the UL database, see www.ul.com
Stripping length (when used without 12 mm (0.47 in); only copper wires may be
Select Online Certifications Directory and enter E194016 as UL File Number.
ferrule) used.
Permissible tightening torque at the 1.0 Nm (8.85 lb.in.)
IND. CONT. EQ. terminal screw

69CA Maximum allowed speed of the used 640 RPM

tool
Location on device To be visible as follows:

NOTE
Battery disposal
The batteries must only be replaced with the same type or another type
recommended by the manufacturer. Improper replacement involves
explosion hazard. For disposing the batteries it is necessary to observe
the local national/international directives.

SIPROTEC 5 – Product information

C53000- B5040-C001-H, Edition 06.2019 1
 SIPROTEC 5 SIPROTEC 5

Product information Product information

Voltage Terminals Unpacking a Device Rated Values Open Source Software

Wire cross-section AWG 22-12 (0.5 mm2 to 2.5 mm2) solid Devices are tested prior to delivery. Devices are packed on site in a way that meets The rated values shown on the name plate of the device have to be observed. The product contains, among other things, Open Source Software developed by third
or stranded with or without listed ferrule, at the requirements of standard ISO 2248. Operating Temperature parties. The Open Source Software used in the product and the license agreements
least certified for a temperature of +105 °C concerning this software can be found in the Readme_OSS. These Open Source
• Check the packing for external transport damage. Damaged packing may Permissible temperature range for permanent operation:
Conductor sleeve with plastic sleeve L = 8 mm to 10 mm (0.31 in to 0.39 in) -10 °C to +55 °C (+14 °F to +131 °F) Software files are protected by copyright. Your compliance with those license
indicate that the devices inside have also sustained damage.
conditions will entitle you to use the Open Source Software as foreseen in the relevant
Stripping length (when used without 10 mm (0.39 in); only copper wires may be • Unpack devices carefully; do not use force. Other Environmental Conditions license. In the event of conflicts between Siemens license conditions and the Open
conductor sleeve) used.
• Visually check the devices to ensure that they are in perfect mechanical Maximum altitude above sea level: 2000 m (6562 ft) Source Software license conditions, the Open Source Software conditions shall prevail
Permissible tightening torque at the 0.6 Nm (5.31 lb.in.) condition. Minimum admissible atmospheric pressure: 783.8 hPa with respect to the Open Source Software portions of the software. The Open Source
terminal screw Degree of pollution: 2 Software is licensed royalty-free. Insofar as the applicable Open Source Software
• Check the enclosed accessories against the delivery note to make sure that
Location on device To be visible as follows: License Conditions provide for it you can order the source code of the Open Source
everything is complete. Degree of Protection (acc. to IEC 60529) Software from your Siemens sales contact - against payment of the shipping and
• Keep the packing in case the devices must be stored or transported elsewhere. For use in environment with degree of pollution 2. handling charges - for a period of at least 3 years since purchase of the Product. We
• The device must be situated in the operating area for at least 2 hours before you Panel surface mounting Front IP54 are liable for the Product including the Open Source Software contained in it pursuant
connect it to the power supply for the first time or after the device has been in to the license conditions applicable to the Product. Any liability for the Open Source
Panel flush mounting Front IP54 Software beyond the program flow intended for the Product is explicitly excluded.
storage. Thus, you ensure temperature equalization and avoid humidity
influences and condensation. Protection against contact IP2x for current terminal (installed) Furthermore any liability for defects resulting from modifications to the Open Source
IP2x for voltage terminal (installed) Software by you or third parties is excluded. We do not provide any technical support
for the Product if it has been modified.
Routine-Test Report When using DIGSI 5 in online mode, you are provided with the option to go to the main
You can download the routine-test report on the following Internet site using the device menu Show Open source information and read and display the Readme_OSS file
serial number: containing the original license text and copyright information.
https://www.ea-testreports.siemens.com/ To do this, the following steps are necessary:
• Switch to online mode.
Voltage Terminals IO111
• Select the device.
Wire cross-section AWG 30-16 (0.14 mm2 to 1.5 mm2) solid Repacking a Device
or stranded with or without listed ferrule, at • If you store devices after incoming inspection, pack them in suitable storage • Select online in the menu bar.
least certified for a temperature of +105 °C packaging. • Click Show Open source information.
Conductor sleeve with plastic sleeve L = 9 mm (0.35 in) • If devices are to be transported, pack them in transport packing.
Stripping length (when used without 9 mm (0.35 in); only copper wires may be NOTE
• Put the accessories supplied in the packing with the device.
conductor sleeve) used.
To read the Readme_OSS file, a PDF viewer must be installed on the
Permissible tightening torque at the 0.22 Nm to 0.26 Nm (1.95 lb.in. to 2.30 lb.in) computer.
terminal screw Storing a Device
In order to operate SIPROTEC 5 devices, a valid DIGSI 5 license is
Location on device To be visible as follows: • Only store devices on which you have carried out an incoming inspection, thus required.
ensuring that the warranty remains valid. The incoming inspection is described in
the Operating manual.
• SIPROTEC devices must be stored in rooms, which are clean and dry. Devices
or associated replacement modules must be stored at a temperature of
-25 °C to +55 °C (-13 °F to 131 °F).
• The relative humidity must be at a level where condensate and ice is prevented
from forming.
• Siemens recommends that you observe a restricted storage temperature range
of +10 °C to +35 °C (50 °F to 95 °F), in order to prevent the electrolytic
capacitors used in the power supply from aging prematurely.
• If the device has been in storage for more than 2 years, connect it to an auxiliary
voltage for 1 to 2 days. This will cause the electrolytic capacitors to form on the
printed circuit board assemblies again.
• If devices are to be shipped elsewhere, you can reuse their transport packaging.
If using other packaging, ensure that the transport requirements according to
ISO 2248 are met. Storage packaging for individual devices is not adequate for
transport purposes.
• The lithium batteries contained in SIPROTEC devices meet all international
requirements of the hazardous goods specifications for the various carriers
(Special Provision 188 of the UN Recommendations on the Transport of
Dangerous Goods, Special Provision A45 of the IATA Dangerous Goods
Regulations, and the ICAO Technical Instructions). This only applies to the
original battery or genuine replacement batteries.

SIPROTEC 5 – Product information

C53000- B5040-C001-H, Edition 06.2019 2