Scribd
Upload
65 views3 pages

Beam (Rectangular)

This document summarizes the bending moment capacity calculation for a single reinforced concrete rectangular beam with two layers of reinforcement bars. The summary shows that the beam's reinforcement meets the requirements for minimum reinforcement ratio, maximum reinforcement ratio, and clear spacing between parallel bars. The calculated bending moment capacity is 12,851.97 inch-kips, which exceeds the maximum bending moment of 0.00 inch-kips applied to the beam.

Uploaded by

HAITHAM ALI
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
65 views3 pages

Beam (Rectangular)

This document summarizes the bending moment capacity calculation for a single reinforced concrete rectangular beam with two layers of reinforcement bars. The summary shows that the beam's reinforcement meets the requirements for minimum reinforcement ratio, maximum reinforcement ratio, and clear spacing between parallel bars. The calculated bending moment capacity is 12,851.97 inch-kips, which exceeds the maximum bending moment of 0.00 inch-kips applied to the beam.

Uploaded by

HAITHAM ALI
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 3

SINGLE REINFORCED CONCRETE RECTANGULAR BEAM (BENDING MOMENT CAPACITY)

This is limited to two layers bars only

d h

Second layer bars

c
b First layer bars

Summary Results
Clear spacing between parallel bars meet requirement
meet minimum reinforcement ratio requirement
meet maxiimum reinforcement ratio requirement

Bending Moment Capacity Mu = 12851.97 Inches-Kips


STAAD.Pro Results Mz max = 0.00 Inches-Kips
Capacity Status PASS

Cross-Section Dimensions
Depth of Beam h= 40 in
Width of Beam b= 20 in

Reinforcement data
Number of layers NLay = 2
First layer bars
Number of Reinforce Bars (1) N= 3
BAR (1) SIZE N0 = 11
Number of Reinforce Bars (2) N= 0
BAR (2) SIZE N0 = 0
Second layer bars
Number of Reinforce Bars(second layer) N= 2
Bar (Second layer) size No = 11

STIRRUP SIZE N0 = 4

STRENGTH REDUCTION FACTOR f= 0.9

MATERIAL
REINFORCE BAR fy = 60000 psi
CONCRETE fc' = 4000 psi

COVER c= 1.5 in
Clear spacing between two layers C2 = 1.375 in

BAR'S DIAMETER db(1) = 1.375 in


db(2) = 0.000 in
db(Second layer) = 1.375 in
db(stirrup) = 0.500 in

AREA OF ONE BAR (1) Ab(1) = p/4*db2(1) = 1.48 in2


AREA OF ONE BAR (2) Ab(2) = p/4*db2(2) = 0.00 in2
AREA OF ONE BAR (second layer) Ab(second layer) = p/4*db2(second layer) = 1.48 in2
Total Area of Tensile Reinforcement Bars As = 7.20 in2

Check limits for reinforcement, based on 7.6, ACI 318-99 7.44 in


Clear spacing between parallel bars meet requirement

Center of gravity of steel dcg = 3.79 in


EFFECTIVE DEPTH OF BEAM d= 36.21 in

STEEL RATIO r = Ab/(b d) = 0.99%

MINIMUM STEEL RATIO rmin = 200/fy = 0.33%


meet minimum reinforcement ratio requirement

Factor b1 based on 10.2.7.3 b1 = 0.850

Reinforcement ratio producing balanced strain condition


rb = 0.85b1fc'/fy(87000/(87000 + fy )) = 2.85%
MAXIMUM STEEL RATIO rmax = 0.75 rb = 2.14%
meet maxiimum reinforcement ratio requirement

Depth of equivalent rectangular stress block a = As fy/(0.85 f'c b) = 6.36 in

Bending Moment Capacity


Mu = f As fy ( d - a/2) = 12851.97 Inchs-kips
Load Case Number
1 2 3
FX
FY
FZ
MX
MY
MZ
MAX INTERMEDIATE
SAGGING MOMENT
OVRALL MAX
SAGGING MOMENT 0

File Name C:\spro2002\staad\examp\us\intro.std


Member Number 1

You might also like