KWIK-CON II+
CONCRETE AND
MASONRY
SCREW
KWIK-CON II+ CONCRETE AND MASONRY SCREW
PRODUCT DESCRIPTION
KWIK-CONN II+ concrete and masonry screw anchors
Anchor System Features and Benefits
• Improved silver KWIK Cote finish that
exceeds 1000 hours of protection from red
rust in ASTM B117
• Salt spray testing
• More durable than zinc plating
• Zinc electroplating and passivation with
chromate require toxic chemicals. The
KWIK Cote zinc rich organic finish is easy
KWIK-CON II+ fastener on the environment
• Zinc electroplating and passivation with
chromate require toxic chemicals. The
KWIK Cote zinc rich organic finish is easy
on the environment
• Applicable specific carbide tipped bits
optimize performance in concrete or
masonry
• Torx Hex washer head for fast secure
driving
• Torx or Phillips flat head for countersunk
KWIK-CON II+ drive tool, and
a Hilti matched tolerance
carbide-tipped drill bit.
Uncracked
concrete
Approvals/Listings
Metro-Dade County NOA 12-0625.05
2 February 2020
KWIK-CON II+ Concrete and Masonry Screw
MATERIAL SPECIFICATIONS
Carbon steel expansion sleeves and spacer sleeves are manufactured from cold rolled steel.
Carbon steel anchors are zinc plated in accordance with ASTM B633, SC 1, Type III.
Stainless steel anchor components are manufactured from AISI Type 304 stainless steel.
MATERIAL SPECIFICATIONS
• Screws manufactured from 1018 to 1022 cold rolled steel case hardened to HRC 45 minimum
Carbon Steel with KWIK Cote1 • Minimum tensile strength and yield strength for the 1/4-in. is 138 ksi and 137 ksi, respectively
• Minimum tensile strength and yield strength for the 3/16-in. is 138 ksi and 137 ksi, respectively
KWIK Cote corrosion resistant coating • KWIK Cote is a zinc-rich basecoat with an aluminum-rich topcoat.
• Screws manufactured from AISI Type 410 stainless steel. Minimum tensile strength and yield strength for the
AISI Type 410 stainless steel1 1/4-in. is 184ksi and 157 ksi, respectively
• Minimum tensile strength and yield strength for the 3/16-in. is 194 ksi and 170 ksi, respectively
• Tapered flat head with #3 Phillips recess for 3/16- and 1/4-in. anchors
• Tapered flat head with T-25 TORX recess for 3/16-in. anchor
Head Styles • Tapered flat head with T-27 TORX recess for 1/4-in. anchor
• 5/16-in. hex washer with internal T-25 TORX recess for 3/16- and 1/4-in.
anchors
• Maximum 0.507 in. for 3/16- and 1/4-in. tapered Philliips flat head and 1/4-in. tapered T-27 TORX flat head
anchors
Head diameter
• Maximum 0.385 in. for 3/16-in. tapered T-25 TORX flat head anchor
• Maximum 0.432 in. maximum for 3/16- and 1/4-in. T-25 TORX hex washer head anchors
Thread diameter • Nominal 3/16-in., Major dia. is 0.217 inches, Minor2 is 0.145 inches
• Nominal 3/16-in. is 0.170 inches
Shank diameter
• Nominal 1/4-in. is 0.224 inches
Lengths (in.) • 1-1/4, 1-3/4, 2-1/4, 2-3/4, 3-1/4, 3-3/4, 4 (See ordering information section)
Thread design • Trilobular, cold formed.
• Nominal 3/16-in. have 8 tpi.
• Nominal 1/4-in. have 8 tpi.
Threads per inch
• Inches of thread per fastener
1.875 inches maximum
Bending capacity • Ductility at 10° minimum
1 Minimum tensile and yield strength are the average of strength measurement of (30) tested samples. These are not minimum steel properties or minimum manufacturing specifications.
2 Minor diameter is the average measurement taken from (30) samples. This is not a controlled dimension.
February 2020 3
DESIGN INFORMATION IN CONCRETE PER ALLOWALBLE STRESS DESIGN
Table 1 — Tension and shear allowable loads in concrete 1,2
Nominal ƒ'c = 2,000 psi ƒ'c = 4,000 psi ƒ'c = 6,000 psi
anchor Nominal
diameter embedment Tension Shear Tension Shear Tension Shear
(in.) in. (mm) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
1 100 260 125 260 185 280
3/16
(25) (0.44) (1.16) (0.56) (1.16) (0.82) (1.25)
1-3/4 275 260 295 265 325 300
3/16
(44) (1.22) (1.16) (1.31) (1.18) (1.45) (1.33)
1 190 325 240 390 275 540
1/4
(25) (0.85) (1.45) (1.07) (1.73) (1.22) (2.40)
1-3/4 425 560 475 600 525 600
1/4
(44) (1.89) (2.49) (2.1) (2.82) (2.3) (2.67)
1 Screws installed in holes drilled with Hilti TKC carbide bits.
2 Allowable loads are based on a safety factor of 4.
Table 2 — Tension and shear ultimate loads in concrete1
Nominal ƒ'c = 2,000 psi ƒ'c = 4,000 psi ƒ'c = 6,000 psi
anchor Nominal
diameter embedment Tension Shear Tension Shear Tension Shear
(in.) in. (mm) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN) lb (kN)
1 400 1,050 500 1,050 750 1,150
3/16
(25) (1.78) (4.67) (2.22) (4.67) (3.34) (5.12)
1-3/4 1,100 1,050 1,180 1,070 1,300 1,200
3/16
(44) (4.89) (4.67) (5.25) (4.76) (5.78) (5.34)
1 760 1,300 970 1,575 1,100 2,175
1/4
(25) (3.38) (5.78) (4.31) (7.01) (4.89) (9.68)
1-3/4 1,700 2,250 1,900 2,400 2,100 2,400
1/4
(44) (7.56) (10.0) (8.5) (10.7) (9.3) (10.7)
1 Screws installed in holes drilled with TKC bits.
Table 3 — Tension and shear allowable loads Table 4 — Tension and shear allowable loads
in hollow block1,2,3,4 in red brick1,2,3
Nominal Nominal
anchor Nominal anchor Nominal
diameter embedment Tension Shear diameter embedment Tension Shear
(in.) in. (mm) lb (kN) lb (kN) (in.) in. (mm) lb (kN) lb (kN)
1 150 225 1 125 235
3/16 3/16
(25) (0.67) (1.00) (25) (0.56) (1.05)
1-3/4 290 300 1-3/4 350 300
3/16 3/16
(44) (1.29) (1.33) (44) (1.56) (1.33)
1 165 275 1 205 415
1/4 1/4
(25) (0.73) (1.22) (25) (0.91) (1.85)
1-3/4 310 400 1-3/4 350 500
1/4 1/4
(44) (1.38) (1.78) (44) (1.56) (2.22)
1 All values for anchors installed in hollow concrete masonry with a minimum prism strength of 1 This test was performed on individual specimens of ASTM C62 common red brick. Due to
1,500 psi. Concrete block may be lightweight, medium-weight or normal-weight conforming the wide variations encountered in the compressive strength of brick, these values should be
to ASTM C90. considered guide values.
2 Screws installed in holes drilled with TKB bits. 2 Allowable loads are based on a safety factor of 4.
3 Allowable loads calculated using a factor of safety of 4. 3 Installation in the mortar joints is outside the scope of the published data.
4 Installation in the mortar joints is outside the scope of the published data.
Load values are for anchors installed a minimum of sixteen diameters on center and Combined shear and tension loading
( ) ( )
a minimum edge distance of sixteen diameters. Anchor spacing may be reduced to Nd Vd
twelve diameters provided loads are reduced by 20 percent. Edge distance may be + ≤ 1.0
N rec Vrec
reduced to six diameters provided loads are reduced by 20 percent in tension and
70 percent in shear.
INSTALLATION INSTRUCTIONS
Installation Instructions For Use (IFU) / Operating Instructions (OI) throughout the document are included with each product
package. They can also be viewed or downloaded online at www.hilti.com. Because of the possibility of changes, always verify that
downloaded IFU are current when used. Proper installation is critical to achieve full performance. Training is available on request.
Contact Hilti Technical Services for applications and conditions not addressed in the (IFU)/Operating Instructions (OI).
4 February 2020
KWIK-CON II+ Concrete and Masonry Screw
ORDERING INFORMATION1
KWIK-CON II+ fasteners
5/16 - in. Magnetic nut setter or T-25 TORX bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 316-114 THWH 3/16 1-1/4 1-1/4 0
KWIK-CON II+ 316-114 THWH Bulk 3/16 1-1/4 1-1/4 0
KWIK-CON II+ 316-134 THWH 3/16 1-3/4 1-3/4 0
KWIK-CON II+ 316-134 THWH Bulk 3/16 1-3/4 1-3/4 0
KWIK-CON II+ 316-214 THWH 3/16 2-1/4 1-3/4 1/2
KWIK-CON II+ 316-234 THWH 3/16 2-3/4 1-3/4 1
KWIK-CON II+ 316-234 THWH Bulk 3/16 2-3/4 1-3/4 1
KWIK-CON II+ 316-314 THWH 3/16 3-1/4 1-3/4 1-1/2
KWIK-CON II+ 316-334 THWH 3/16 3-3/4 1-3/4 2
KWIK-CON II+ 316-4 THWH 3/16 4 1-3/4 2-1/4
5/16 - in. Magnetic nut setter or T-25 bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 14-114 THWH 1/4 1-1/4 1-1/4 0
KWIK-CON II+ 14-114 THWH Bulk 1/4 1-1/4 1-1/4 0
KWIK-CON II+ 14-134 THWH 1/4 1-3/4 1-3/4 0
KWIK-CON II+ 14-134 THWH Bulk 1/4 1-3/4 1-3/4 0
KWIK-CON II+ 14-214 THWH 1/4 2-1/4 1-3/4 1/2
KWIK-CON II+ 14-234 THWH 1/4 2-3/4 1-3/4 1
KWIK-CON II+ 14-234 THWH Bulk 1/4 2-3/4 1-3/4 1
KWIK-CON II+ 14-314 THWH 1/4 3-1/4 1-3/4 1-1/2
KWIK-CON II+ 14-334 THWH 1/4 3-3/4 1-3/4 2
KWIK-CON II+ 14-334 THWH Bulk 1/4 3-3/4 1-3/4 2
KWIK-CON II+ 14-4 THWH 1/4 4 1-3/4 2-1/4
KWIK-CON II+ 14-114 THWH Stainless Steel 1/4 1-1/4 1-1/4 0
KWIK-CON II+ 14-234 THWH Stainless Steel 1/4 2-3/4 1-3/4 1
T-25 TORX bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 316-114 TFH 3/16 1-1/4 1-1/8 0
KWIK-CON II+ 316-134 TFH 3/16 1-3/4 1-5/8 0
KWIK-CON II+ 316-134 TFH Bulk 3/16 1-3/4 1-5/8 0
KWIK-CON II+ 316-214 TFH 3/16 2-1/4 1-3/4 3/8
KWIK-CON II+ 316-234 TFH 3/16 2-3/4 1-3/4 7/8
KWIK-CON II+ 316-234 TFH Bulk 3/16 2-3/4 1-3/4 7/8
KWIK-CON II+ 316-314 TFH 3/16 3-1/4 1-3/4 1-3/8
KWIK-CON II+ 316-334 TFH 3/16 3-3/4 1-3/4 1-7/8
KWIK-CON II+ 316-334 TFH Bulk 3/16 3-3/4 1-3/4 1-7/8
KWIK-CON II+ 316-4 TFH 3/16 4 1-3/4 2-1/8
T-27 TORX bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 14-114 TFH 1/4 1-1/4 1-1/16 0
KWIK-CON II+ 14-134 TFH 1/4 1-3/4 1-9/16 0
KWIK-CON II+ 14-134 TFH Bulk 1/4 1-3/4 1-9/16 0
KWIK-CON II+ 14-214 TFH 1/4 2-1/4 1-3/4 5/16
KWIK-CON II+ 14-234 TFH 1/4 2-3/4 1-3/4 13/16
KWIK-CON II+ 14-314 TFH 1/4 3-1/4 1-3/4 1-5/16
KWIK-CON II+ 14-314 TFH Bulk 1/4 3-1/4 1-3/4 1-5/16
KWIK-CON II+ 14-334 TFH 1/4 3-3/4 1-3/4 1-13/16
KWIK-CON II+ 14-4 TFH 1/4 4 1-3/4 2-1/16
Total Length Total Length
1 All dimensions in inches
Shank Shank
Thread length length Thread length length
February 2020 5
KWIK-CON II+ fasteners
#3 Phillips bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 316-114 PFH 3/16 1-1/4 1-1/16 0
KWIK-CON II+ 316-134 PFH 3/16 1-3/4 1-9/16 0
KWIK-CON II+ 316-214 PFH 3/16 2-1/4 1-3/4 5/16
KWIK-CON II+ 316-234 PFH 3/16 2-3/4 1-3/4 13/16
KWIK-CON II+ 316-314 PFH 3/16 3-1/4 1-3/4 1-5/16
KWIK-CON II+ 316-334 PFH 3/16 3-3/4 1-3/4 1-13/16
KWIK-CON II+ 316-4 PFH 3/16 4 1-3/4 2-1/16
KWIK-CON II+ 316-114 PFH Stainless Steel 3/16 1-1/4 1-1/16 0
KWIK-CON II+ 316-234 PFH Stainless Steel 3/16 2-3/4 1-3/4 13/16
#3 Phillips bit
Description Diameter Total length Thread length Shank length
KWIK-CON II+ 14-114 PFH 1/4 1-1/4 1-1/16 0
KWIK-CON II+ 14-134 PFH 1/4 1-3/4 1-9/16 0
KWIK-CON II+ 14-214 PFH 1/4 2-1/4 1-3/4 5/16
KWIK-CON II+ 14-234 PFH 1/4 2-3/4 1-3/4 13/16
KWIK-CON II+ 14-314 PFH 1/4 3-1/4 1-3/4 1-5/16
KWIK-CON II+ 14-334 PFH 1/4 3-3/4 1-3/4 1-13/16
KWIK-CON II+ 14-4 PFH 1/4 4 1-3/4 2-1/16
KWIK-CON II+ hex driver system
Description Qty / pack
KWIK-CON Hex Driver Deluxe Kit 1
KWIK-CON Hex Driver 1
5/16-in. Hex Driver for all THWH 1
5/16-in. Hex Nut Setter/Depth Locator 1
Insert Bit Holder/Depth Locator 1
#3 Phillips Driver for all PFH 1
T-25 TORX Driver for 3/16-in. TFH 1
T-27 TORX Driver for 1/4-in. TFH 1
KWIK-CON II+ matched tolerance drill bits
Description
For 1/4-in. KWIK-CON II+ Applications in normal-weight concrete
TKC Large Concrete Bit SDS+ Hex
TKC Large Concrete Bit Smooth Shank
For 1/4-in. KWIK-CON II+ Applications in lightweight concrete, brick or block
TKB Large Block Bit SDS+ Hex
TKB Large Block Bit Smooth Shank
For 3/16-in. KWIK-CON II+ Applications in normal-weight concrete
TKC Small Concrete Bit SDS+ Hex
TKC Small Concrete Bit Smooth Shank
For 3/16-in. KWIK-CON II+ Applications in lightweight concrete, brick or block
TKB Small Block Bit SDS+ Hex
TKB Small Block Bit Smooth Shank
Total Length Total Length
Shank Shank
Thread length length Thread length length
1 All dimensions in inches.
6 February 2020
KWIK-CON II+ Concrete and Masonry Screw
DBS • 02/20
Hilti, Inc. 1-800-879-8000
en español 1-800-879-5000 Hilti (Canada) Corporation 1-800-363-4458
www.hilti.com www.hilti.ca
February 2020 7
