Scribd
Upload
328 views2 pages

ISO Tolerances For Shafts (ISO 286-2)

ISO 286-2 provides tolerances for shaft sizes in millimeters. It specifies maximum and minimum tolerances for nominal shaft diameters ranging from 3mm to 400mm in micrometers. Tighter tolerances are required for smaller shaft sizes, with allowances increasing with larger shaft diameters. The standard outlines 12 tolerance grade designations from h4 to h12 to define acceptable dimensional deviations for circular shafts.

Uploaded by

Nitin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
328 views2 pages

ISO Tolerances For Shafts (ISO 286-2)

ISO 286-2 provides tolerances for shaft sizes in millimeters. It specifies maximum and minimum tolerances for nominal shaft diameters ranging from 3mm to 400mm in micrometers. Tighter tolerances are required for smaller shaft sizes, with allowances increasing with larger shaft diameters. The standard outlines 12 tolerance grade designations from h4 to h12 to define acceptable dimensional deviations for circular shafts.

Uploaded by

Nitin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

3/9/22, 2:59 PM ISO Tolerances for Shafts (ISO 286-2)

ISO Tolerances for Shafts (ISO 286-2)

Nominal Shaft Sizes (mm)


over 3 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355

inc. 6 10 18 30 40 50 65 80 100 120 140 160 180 200 225 250 280 315 355 400

micrometres
-270 -280 -290 -300 -310 -320 -340 -360 -380 -410 -460 -520 -580 -660 -740 -820 -920 -1050 -1200 -1350
a12 -390 -430 -470 -510 -560 -570 -640 -660 -730 -760 -860 -920 -980 -1120 -1200 -1280 -1440 -1570 -1770 -1920
-30 -40 -50 -65 -80 -100 -120 -145 -170 -190 -210
d6 -38 -49 -61 -78 -96 -119 -142 -170 -199 -222 -246
-20 -25 -32 -40 -50 -60 -72 -85 -100 -110 -125
e6 -28 -34 -43 -53 -66 -79 -94 -110 -129 -142 -161
-25 -32 -40 -50 -60 -72 -85 -100 -110 -125
e13 -20 -200
-245 -302 -370 -440 -520 -612 -715 -820 -920 -1015
-13 -16 -25 -30 -36 -43 -50 -56 -62
f5 -10 -15
-19 -24
-20 -29
-36 -43 -51 -61 -70 -79 -87
-10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62
f6 -18 -22 -27 -33 -41 -49 -58 -68 -79 -88 -98
-10 -13 -16 -20 -25 -30 -36 -43 -50 -56 -62
f7 -22 -28 -34 -41 -50 -60 -71 -83 -96 -108 -119
-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18
g5 -9 -11 -14 -16 -20 -23 -27 -32 -35 -40 -43
-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18
g6 -12 -14 -17 -20 -25 -29 -34 -39 -44 -49 -54
-4 -5 -6 -7 -9 -10 -12 -14 -15 -17 -18
g7 -16 -20 -24 -28 -34 -40 -47 -54 -61 -69 -75
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h4 -4 -4 -5 -6 -7 -8 -10 -12 -14 -16 -18
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h5 -5 -6 -8 -9 -11 -13 -15 -18 -20 -23 -25
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h6 -8 -9 -11 -13 -16 -19 -22 -25 -29 -32 -36
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h7 -12 -15 -18 -21 -25 -30 -35 -40 -46 -52 -57
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h8 -18 -22 -27 -33 -39 -46 -54 -63 -72 -81 -89
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h9 -30 -36 -43 -52 -62 -74 -87 -100 -115 -130 -140
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h10 -48 -58 -70 -84 -100 -120 -140 -160 -185 -210 -230
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h11 -75 -90 -110 -130 -160 -190 -220 -250 -290 -320 -360
-0 -0 -0 -0 -0 -0 -0 -0 -0 -0 -0
h12 -120 -150 -180 -210 -250 -300 -350 -400 -460 -520 -570
+3 +4 +5 +5 +6 +6 +6 +7 +7 +7 +7
j5 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18
+6 +7 +8 +9 +11 +12 +13 +14 +16 +16 +18
j6 -2 -2 -3 -4 -5 -7 -9 -11 -13 -16 -18
+8 +10 +12 +13 +15 +18 +20 +22 +25 +26 +29
j7 -4 -5 -6 -8 -10 -12 -15 -18 -21 -26 -28
+2.5 +3 +4 +4.5 +5.5 +6.5 +7.5 +9 +10 +11.5 +12.5
js5 -2.5 -3 -4 -4.5 -5.5 -6.5 -7.5 -9 -10 -11.5 -12.5
+4 +4.5 +5.5 +6.5 +8 +9.5 +11 +12.5 +14.5 +16 +18
js6 -4 -4.5 -5.5 -6.5 -8 -9.5 -11 -12.5 -14.5 -16 -18
+6 +7.5 +9 +10.5 +12.5 +15 +17.5 +20 +23 +26 +28.5
js7 -6 -7.5 -9 -10.5 -12.5 -15 -17.5 -20 -23 -26 -28.5
+6 +7 +9 +11 +13 +15 +18 +21 +24 +27 +29
k5 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4
+9 +10 +12 +15 +18 +21 +25 +28 +33 +36 +40
k6 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4
+13 +16 +19 +23 +27 +32 +38 +43 +50 +56 +61
k7 +1 +1 +1 +2 +2 +2 +3 +3 +4 +4 +4
+9 +12 +15 +17 +20 +24 +28 +33 +37 +43 +46
m5 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21
+12 +15 +18 +21 +25 +30 +35 +40 +46 +52 +57
m6 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21
+16 +21 +25 +29 +34 +41 +48 +55 +63 +72 +78
m7 +4 +6 +7 +8 +9 +11 +13 +15 +17 +20 +21
+13 +16 +20 +24 +28 +33 +38 +45 +51 +57 +62
n5 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37
+16 +19 +23 +28 +33 +39 +45 +52 +60 +66 +73
n6 +8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37
n7 +20 +25 +30 +36 +42 +50 +58 +67 +77 +86 +94

https://www.tribology-abc.com/calculators/iso_shafts.htm 1/2
3/9/22, 2:59 PM ISO Tolerances for Shafts (ISO 286-2)
+8 +10 +12 +15 +17 +20 +23 +27 +31 +34 +37
+17 +21 +26 +31 +37 +45 +52 +61 +70 +79 +87
p5 +12 +15 +18 +22 +26 +32 +37 +43 +50 +56 +62
+20 +24 +29 +35 +42 +51 +59 +68 +79 +88 +98
p6 +12 +15 +18 +22 +26 +32 +37 +43 +50 +56 +62
+23 +28 +34 +41 +50 +60 +62 +73 +76 +88 +90 +93 +106 +109 +113 +126 +130 +144 +150
r6 +15 +19 +23 +28 +34 +41 +43 +51 +54 +63 +65 +68 +77 +80 +84 +94 +98 +108 +114

https://www.tribology-abc.com/calculators/iso_shafts.htm 2/2

You might also like