1.

Negative Terminal Post

2.. Pressure Controlled Vent Valves
3. Inter-cell Connector
4. Positive Terminal Post
6. Container Cover
5. Sealing Compound Epoxy
7. Sealing O-Ring
8. Positive Plate
9. AGM Separator
10. Negative Plate
11. Case

Canada: 1-888-271-8888 www.magnacharge.com USA: 1-844-370-0258

SLA Models and Parameters
Typical Applications

• All purpose • Uninterruptable Power Supply (UPS) • Electric Power System (EPS)
• Emergency backup power supply • Emergency light • Railway signal
• Aircraft signal • Electronic apparatus and equipment • Alarm and security system
• Communication power supply • DC power supply • Auto control system
• Mobility • Medical devices

Nominal Rated Capacity (AH) Approx dimension (inch) Approx

Carton Terminal
Model Voltage 20HR 10HR 5HR 1HR Weight
Total
Length Width Height Height QTY Type
(V) 1.80V/cell 1.80V/cell 1.75V/cell 1.60V/cell kg lbs.

6 VOLT
SLA6-1.2 6 1.20 1.12 1.02 0.75 3.82 0.94 2.03 2.26 0.29 0.64 30 T1
SLA6-2.8 6 2.80 2.60 2.38 1.76 2.60 1.30 3.82 4.06 0.57 1.26 20 T1
SLA6-3.2 6 3.20 2.98 2.72 2.01 5.28 1.34 2.36 2.60 0.67 1.48 20 T1
SLA6-4.5 6 4.50 4.19 3.83 2.83 2.76 1.85 3.98 4.17 0.81 1.79 20 T1
SLA6-7 6 7.50 6.98 6.38 4.71 5.94 1.34 3.70 3.94 1.26 2.78 8 T1/T2
SLA6-8.5 6 8.50 7.91 7.23 5.34 3.86 2.20 4.65 4.72 1.52 3.35 10 T1/T2
SLA6-12 6 12.00 11.16 10.20 7.54 5.94 2.01 3.70 3.94 1.95 4.30 8 T1/T2
SLA6-20 6 20.00 18.60 17.00 12.56 6.18 3.27 4.92 4.92 3.21 7.08 4 T3
SLA-6V27L 6 210.00 200.00 172.00 122.00 12.05 6.61 8.74 8.98 28.2 62.2 1 T8/T11

12 VOLT
SLA12-0.8 12 0.80 0.74 0.68 0.50 3.78 0.98 2.44 2.44 0.35 0.77 20 CONNECTOR
SLA12-1.2 12 1.20 1.12 1.02 0.75 3.82 1.69 2.05 2.28 0.57 1.26 20 T1
SLA12-2.3 12 2.30 2.14 1.96 1.44 7.01 1.38 2.36 2.60 0.78 1.72 20 T1
SLA12-3.5 12 3.20 2.98 2.72 2.01 5.28 2.64 2.38 2.62 1.35 2.98 10 T1
SLA12-4.5 12 4.50 4.19 3.83 2.83 3.54 2.76 3.98 4.21 1.48 3.26 10 T1/T2
SLA12-5 12 4.77 4.5 3.90 2.77 5.94 2.09 3.66 3.90 1.90 4.19 6 T1/T2
SLA12-5.4 12 5.40 5.00 4.60 3.39 3.54 2.76 3.98 4.21 1.88 4.15 10 T1
SLA12-7 12 7.20 6.70 6.12 4.52 5.94 2.56 3.68 3.90 2.35 5.18 8 T1/T2
SLA12-9 12 9.00 8.37 7.65 5.65 5.94 2.56 3.68 3.90 2.45 5.40 5 T1/T2/T3
SLA12-10 12 10.00 9.30 8.50 6.28 5.94 2.56 4.37 4.61 3.20 7.06 4 T1/T2
SLA12-12 12 12.70 12.00 10.04 7.38 5.94 3.86 3.74 3.98 3.80 8.38 4 T1/T2
SLA12-14 12 14.00 13.02 11.90 8.79 5.94 3.86 3.74 3.98 4.05 8.93 4 T1/T2
SLA12-18 12 19.10 18.00 15.60 11.10 7.15 3.03 6.59 6.59 5.70 12.57 2 T2
SLA12-20 12 20.00 18.90 17.20 13.10 7.15 3.03 6.59 6.59 6.00 13.23 2 T3/T12
SLA12-24 12 25.80 24 21.10 15.50 6.50 4.92 6.89 7.17 9.10 20.06 1 T3/T12
SLA12-28 12 28.00 26.04 23.80 17.58 6.54 6.89 4.92 4.92 8.40 18.50 1 T3/T12
SLA12-33 12 33.00 30.69 28.05 20.72 7.68 5.12 6.46 7.09 10.50 23.30 1 T5/T6/T12
SLA12-33G* 12 33.00 30.69 28.05 20.72 7.68 5.12 6.46 7.01 10.70 23.60 1 T5/T6
SLA12-38G* 12 38.00 35.30 30.40 20.90 7.76 6.50 6.69 6.69 13.50 29.80 1 T6
SLA12-45 12 45.00 42.00 36.50 26 7.76 6.50 6.69 6.69 14.50 32.00 1 T6/T12
SLA12-55 12 57.20 55.00 47.90 34.10 9.02 5.43 8.27 9.06 17.70 39.00 1 T6/T9/T14
SLA12-55G* 12 57.20 55.00 47.30 33.55 9.02 5.43 8.07 8.31 16.60 36.60 1 T6
SLA12-70G* 12 70.00 65.10 56.00 38.5 10.24 6.61 8.19 8.43 22.80 50.30 1 T6
SLA12-75 12 80.30 75.00 65.30 46.5 10.24 6.61 8.19 9.06 22.70 50.10 1 T6/T14
SLA12-90 12 96.30 90.00 78.30 55.80 12.05 6.61 8.15 8.98 62.40 28.30 1 T11
SLA12-100 12 107.00 100.00 87.00 62.00 12.99 6.81 8.35 8.66 32.00 70.60 1 T11
SLA12-150 12 160.50 150.00 130.50 93.00 19.02 6.69 9.39 9.39 47.20 104.10 1 T11
SLA12-200 12 214.00 200.00 174.00 124.00 20.55 9.45 8.58 8.82 64.00 141.10 1 T11
SLA12-250 12 260.00 250.00 215.00 152.50 20.55 10.06 8.66 8.90 73.00 161.00 1 T11
1 Year Warranty - Cycling Applications 6 Month Warranty * Gel Technology 04/2020
A VRLA-AGM battery is an electric storage lead-acid battery.
• Sealed with Proprietary compound epoxy and using pressure controlled vent valves.
• Starved electrolyte design - acid solution is absorbed in glass mat separators
• ABS material - increases structural integrity (Flame-retardant ABS is optional)
• Using a recombination reaction to prevent the release of hydrogen and oxygen gases.
• Non-spillable - can be operated in any position (upside down installation is not recommended)
• Maintenance free - connections must be retorqued and the batteries should be cleaned periodically.
A VRLA-AGM battery uses recombinant technology. The oxygen produced from the positive plates of the battery is absorbed by the
negative plates. This suppresses the generation of hydrogen at the negative plates. The recombination of oxygen and hydrogen leads
to Water (H2O), retaining the electrolyte amount within the battery. Water filling is never required. Battery should never be opened as this
would damage the battery with additional oxygen from the air. The warranty will be void if the battery is opened.

BATTERY TERMINAL OPTIONS Note: the figures below just show the appearance and dimension. Unit: mm[inch]

T1 FASTON TYPE (Copper)

quick disconnect tabs; T2 FASTON TYPE (Copper)
quick disconnect tabs; T3 Brass Coated With Tin
T3 Terminal Torque: 3.9 ~ 5.4 N*m
TERMINAL silver coating for better conductivity TERMINAL silver coating for better conductivity TERMINAL (34.39 ~ 47.75 in*lbs)

T4 FASTON TYPE (Copper)

quick disconnect tabs; T4 Brass Coated With Tin T5 Lead
T5 Terminal Torque:
TERMINAL silver coating for better conductivity TERMINAL TERMINAL 3.9 ~ 5.4 N*m(34.39 ~ 47.75 in*lbs)

T6-I Brass; Threaded Insert 6mm STUD

Torque: 3.9 ~ 5.4 N*m (34.39 ~ 47.75 in*lbs)
T7 Brass Coated With Tin; Threaded
Insert 6mm STUD T9 Lead
Torque:
TERMINAL TERMINAL Torque: 3.9 ~ 5.4 N*m(34.39 ~ 47.75 in*lbs) TERMINAL 11 ~ 14.7 N*m(97.28 ~ 130.0 in*lbs)

T10 Lead
Torque: 3.9 ~ 5.4 N*m(34.39 ~ 47.75 in*lbs)
T11 Brass Coated With Tin; Threaded Insert 8mm STUD
Torque: 11~14.7 N*m(97.28 ~ 130.0 in*lbs)
T12
TERMINAL
Brass Coated; Threaded Insert 5mm STUD
Torque: 2.0 ~ 3.0 N*m (17.69 ~ 26.53 in*lbs)
TERMINAL TERMINAL

T12-I Brass; Threaded Insert 5mm STUD

Torque: 2.0 ~ 3.0 N*m (17.69 ~ 26.53 in*lbs)
T13 Brass Coated With Tin; Threaded Insert 6mm STUD
Torque: 3.9 ~ 5.4 N*m(34.39 ~ 47.75 in*lbs)
T14-1 Lead
Torque: 11 ~ 14.7 N*m(97.28 ~ 130.0 in*lbs)
TERMINAL TERMINAL POSITIVE

T14-2 Lead
Torque: SPRING Spring Steel Fully Collapsible CONNECTOR
Toy Battery Connector
H-Connector
NEGATIVE 11 ~ 14.7 N*m(97.28 ~ 130.0 in*lbs)
FEATURES Charge Voltages and
Temperature Ranges
State of charge vs.
Open circuit voltage
• Maintenance-free
• Sealed - valve regulated
Optimum Maximum Optimum Maximum
• Spill proof / leak proof
• Deep discharge protection
• Plate grid - lead calcium alloy (PbCaSn)
• Corrosion free
• Vertical or horizontal installation
• Low gassing (unless overcharged)
• High cycling and stationary performance
• Engineered for high rate discharge
• Vibration resistance
• Long shelf life

Discharge characteristics Charging characteristics (standby use)

12V 6V 4V 2V
Battery Battery Battery Battery Charge Charging Charging Charging
V V V V 0
Temperature:25C Volume Current Voltage Voltage
13.0 6.5 4.33 2.16
(V) (V) 0.10CA-2.25V/cell temperature250C
% (XCA) (V)

12.0 6.0 4.00 2.00 0.25

120 15.0 7.5 2.50
Charged Volume
Terminal Voltage(V)

110
11.0 5.5 3.66 1.84 0.20
100
14.0 7.0 2.33
0.093C 0.05C 90
0.207C Charge Voltage
10.0 5.0 3.33 1.68 0.4C 80 0.15 (Constant 2.25v/cell)
70 13.0 6.5 2.17
1C 0.628C 60
9.0 4.5 3.00 1.52 After 50% Discharge
50 0.10 12.0 6.0 2.00
40 After 100% Discharge
8.0 4.0 2.67 1.36 30
0.05 11.0 5.5 1.83
3C 2C 20
10 Charging Current
1 2 4 6 8 10 20 40 60 2 4 6 8 10 20
0 0
Min H 0 4 8 12 16 20 24 28 32 36 40

Discharge Time Charging Time(hours)

Self discharge characteristics Effect of temperature on long term float life

10
100
8
10 C
0 A
80 6
Remaining Capacity(%)

0 5
25 C Charging voltage :
B 4
Float Life (year)

60 2.25V/cell
3
400C 300C
40 2

C
20
1
0
0 2 4 6 8 10 12
Storage Time(Months) 0.5
20 30 40 50 0C
No supplementary charge required 68 86 104 122 OF
A (Carry out supplementary charge before use if 100% capacity is required.)
Battery temperature
Supplementary charge required before use. See charging options below:
1.Charged for 3 plus (+) days at limited current 0.25CA and constant voltage 2.25V/cell.
B 2.Charged for 20 plus (+) hours at limited current 0.25CA and constant voltage 2.45V/cell.
3.Charged for 8~10hours at limited current 0.05CA .
Discharged batteries may not recover full capacity.
Cycle service life in relation to depth of discharge
C Batteries should never be left in a state of discharge.
Testing condition
Discharging current: 0.17C (FV 1.7V/cell);
Charging current: 0.25C max, voltage 2.45V/cell;
Temperature effects in relation to battery capacity Charging volume:125% of discharged capacity.

120 120

100 CA
0 .0 5 100
A
0 .1 C
%

80 80
Capacity(%)

0 .2 C A
Capacity

60
60
1 .0 C A 100% 50% 30%
40 DOD DOD DOD
A 40
2 .0 C 3. 0C A Ambient Termperature:
20 25oC (77oF)
20
0
-20 -10 0 10 20 30 40 50 0
0 200 400 600 800 1000 1200
Temperature(0C) Number of Cycles