Scribd
Upload
80 views10 pages

MS-M-07-MATERIAL SUBMITTAL - (Galvanized Duct)

This document provides information on Borusan Engineering's Hot Dip Galvanizing Line (CGL2) and summarizes the mechanical properties of Borusan's steel products. CGL2 uses a continuous process to degrease, pickle, rinse and heat treat steel strips before dipping them in molten zinc for coating. The line can process steel between 0.35-4mm thick and 600-1300mm wide, applying a 100-350g/m2 zinc coating. The summary table lists the various steel products' yield strengths, tensile strengths, and minimum elongation percentages.

Uploaded by

khalil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
80 views10 pages

MS-M-07-MATERIAL SUBMITTAL - (Galvanized Duct)

This document provides information on Borusan Engineering's Hot Dip Galvanizing Line (CGL2) and summarizes the mechanical properties of Borusan's steel products. CGL2 uses a continuous process to degrease, pickle, rinse and heat treat steel strips before dipping them in molten zinc for coating. The line can process steel between 0.35-4mm thick and 600-1300mm wide, applying a 100-350g/m2 zinc coating. The summary table lists the various steel products' yield strengths, tensile strengths, and minimum elongation percentages.

Uploaded by

khalil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

4) Hot Dip Galvanizing Line (CGL2)

Borusan Engineering-Turkey and Celes-France


Radiometri-Belgium, FIFE-Germany

In CGL 2 line, for the surface preparation, the steel strip passes continuously through chemical
baths as degreasing unit, pickling-rinsing and then through induction heated atmosphere
controlled furnace and after steel strip dip into galvanizing pot for zinc coating.

Hot Dip Galvanizing Line


Production capacity : 80,000 ton/an
Thickness range : 0.35-4.00 mm
Width range : 600-1300 mm
Coating thickness (double side) : 100-350 gr/m2

• Tension Leveller: Performs correction of flatness up to 3 IU


• Chromating: To passivate the strip surface
• Ink jet printer: Print the customer requirements on the strip
BORÇEL‹K - 8
Material Standards

HOT DIP GALVANIZED STEEL

ASTM
EN 10327 DIN 17162/1 NFA 36-321 BS 2989 JIS 3302
A653-95

St01Z Z1 CQ

DX51 D+Z St02Z GC Z2 SGCC LFQ

DX52 D+Z St03Z GE Z3 SGCD1 DQ

DX53 D+Z St04Z GES Z4 SGCD2 DQSK

DX54 D+Z SGCD3

DX56 D+Z

ASTM
EN 10326 DIN 17162/2 NFA 36.322 BS 2989 JIS 3302
A653-95

S220GD+Z C230 Z 22 SQ-Grade 230

S250GD+Z StE 250-2Z C250 Z 25 SGC 340 SQ-Grade 255

S280GD+Z StE 280-2Z C280 Z 28 SGC 400 SQ-Grade 275

S320GD+Z StE 320-3Z C320 SGC 440

S350GD+Z StE 350-3Z C350 Z 35 SGC 490 SQ-Grade 340


MATERIAL STANDARDS - 1
Summary Table of
Mechanical Properties of Borçelik Products

YIELD STRENGTH TENSILE STRENGTH ELONGATION (%)


QUALITY
(MPa) (MPa) A 80 A5
HOT DIP GALVANIZED
STEEL t≤3 t≤3 t≤3

DX51D+Z 270-500 min. 22

DX52D+Z 140-300 270-420 min. 26

DX53D+Z 140-260 270-380 min. 30

DX54D+Z 140-220 270-350 min. 36

DX56D+Z 120-180 270-350 min. 39

S220GD+Z min. 220 min. 300 min. 30

S250GD+Z min. 250 min. 330 min. 19

S280GD+Z min. 280 min. 360 min. 18

S320GD+Z min. 320 min. 390 min. 17

S350GD+Z min. 350 min. 420 min. 16

H260LAD 260-330 350-430 min. 26

H300LAD 300-380 380-480 min. 23

H340LAD 340-420 410-510 min. 21

H380LAD 380-480 440-560 min. 19


SUMMARY TABLE OF MECHANICAL PROPERTIES OF BORÇEL‹K PRODUCTS - 1

H420LAD 420-520 470-590 min. 17

BH 180 180-230 300-360 min. 34

BH 220 220-270 340-400 min. 32

RH 220 220-260 min. 340 min. 32

RH 235 235-275 min. 355 min. 32

RH 260 260-310 min. 370 min. 30

RH 280 280-330 min. 385 min. 30

DP 450 260-340 450-530 min. 27

DP 500 300-380 500-580 min. 25

DP 600 320-400 600-700 min. 21

You might also like