Hisense USER MANUAL Read the manual carefully and ensure you have fully understood its contents before operating this device for the first time. Englishos | | ‘mportant Notice Paragraphs beginning with the symbol 4M indicate important instructions, tips or conditions for the following settings. For your own safety and the optimal performance of your TV, ensure to read the safety instructions before performing any installation. It is not guarantee operation and performance of peripheral devices made by other manufacturers. We disclaim any liability or damage that may arise from operation and/ or performance from usage of such other maker's peripheral devices. The recording and playback of content on this or any other device may require permission from the owner of the copyright or other such rights in that content. It is your responsibility to ensure that your use of this or any other device complies with applicable copyright legislation in your country. Please refer to that legislation for more information on the relevant laws and regulations involved or contact the owner of the rights of the content you wish to record or playback. The Index/Glossary explains certain terms used in this manual and in the TV menu. Read these instructions Follow all instructions Heed all warnings Keep these instructions All rights reserved | Safety Instructions To ensure safe and correct use of this product, always comply with the following precautions to avoid dangerous situations and damage to your unit: The lightning flash with arrowhead CAUTION A symbol, within an equilateral triangle is intended to alert the user to the presence DO NOT OPEN, of uninsulated dangerous voltage within CAUTION: TO REDUCE THE RISK OF ELECTRIC ‘SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ( The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance X= AC voltage: This symbol indicates that the rated voltage marked with the symbol is AC voltage. Class 11 product : This symbol indicates that it does not require a safety connection of protective earthing (ground). (only for 55") Class | product: This symbol indicates that it requires a safety connection of protective earthing (ground). (only for 65")| The intended use and ambient conditions for this TV This TV is intended for the rendering of video and audio signals, on a table-top or wall- mounted, in a home or office environment. It must not be used in rooms with a high level of humidity or dust concentration. The warranty is only valid if used as intended by the manufacturer. Awernine High humidity and dust concentration may lead to current leaks in the device. To reduce the risk of fire or electrical shock: Do not expose this unit to rain, moisture, dripping or splashing water, and do not place objects filled with liquids, such as vases, cups, etc. on or over the unit. Do not touch the TV with wet hands. Do not expose to direct air-conditioning and keep candles or other naked flames away from the TV at all times. If the TV is moved from a cold environment to a hot environment, leave it switched off for at least an hour to avoid condensation. If used outside, make sure it is protected from moisture. If you notice anything unusual, immediately remove the power plug In case of fire, use preferably a CO, gas or powder fire extinguisher. If such extinguishers are not accessible, try to isolate the electrical supply before using a water fire extinguisher. WARNING Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: - Using cabinets or stands recommended by the manufacturer of the television set. Only using furniture that can safely support the television set. Ensuring the television set is not overhanging the edge of the supporting furniture. Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and television set to a suitable support. Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture Educating children about the dangers of climbing on furniture to reach the television set or its controls If your existing television set is being retained and relocated, the same considerations as above should be applied. Bos | @ Moving/Transportation Before moving this TV, disconnect all cables and move in the vertical position only. Grasp the device on the upper and lower edges of the frame. - Do not press or put stress on the front panel of the TV. It may take two or more people to carry larger TVs If you have to briefly lay down the TV, place the unit with its entire front surface lying flat on soft material. The screen is made of glass and can break if is not handled properly. Always wear rubber gloves to carry the unit. If the screen is damaged, liquid crystal might leak out. In case of skin contact, immediately rinse thoroughly with water. m@ Power Supply Incorrect voltages can damage the TV. Only connect this unit to a power supply with the correct voltage and frequency noted on the type plate, using the supplied power cable The power plug must be easily accessible so that the device can be disconnected at all time. The unit is live, even if in standby mode, as long as the unit is connected to a power outlet. It is recommended that this unit is placed on a dedicated circuit. - Do not overload the power outlets by connect too many appliances to the same outlet. Overloaded wall outlets, extension cords, etc. are dangerous and can result in electric shock and fire. After power off, don't turn it on again in 5 seconds. Frequent switching power supply in a short period of time can cause abnormal TV. @ Power plug and power cable - Do not touch the power plug with wet hands. - Do not place heavy objects on the power cable. Route the cable so that it is not kinked or laid over sharp edges, walked on or exposed to chemicals. A power cable with damaged insulation can cause electric shock and fire Pull the power plug, NOT on the cable when disconnecting. The cable can become damaged and cause a short circuit if pulled on - Do not place the power cable near a high temperature object. - Do not move the TV with the power cable plugged into a socket. - Do not use a damaged or loose power cable, or a damaged socket outlet. = Do not use any power cords other than the one supplied with this unit. @ Set-up Check that the location is suitable to bear the load of the TV. Place on a level, sturdy and horizontal base. Ensure that the unit does not hang over the edge of the base when placed in or on furniture. If placed on a cart, use caution when moving to avoid the unit from tipping over. - Place the unit in a normal upright horizontal position. It must never be operated vertically, lying flat or hanging overhead from the ceiling. - Place the unit where it is not exposed to direct sunlight or other sources of heat. When mounting the TV on a wall, follow the instructions supplied with the wall- mount, make sure not to install the TV by hanging the power and signal cables on the back of the TV.ns | @ Air ventilation and high temperatures Install your TV only where there is proper ventilation, and ensure that there is at least 10 cm free space on the sides and 20 cm above the unit for air circulation. Excessive heat and obstruction of ventilation could lead to fire or early failure of some electric components. = Do not block any ventilation openings with newspapers, tablecloths, curtains, ete. - Do not dry clothing etc. on top of the unit - Take care not to touch the ventilation openings since they may become hot. - Do not insert foreign objects into the TV through the vents. @ The Stand - Do not use any stand other than the one supplied with this unit. - Do not modify or use the stand if it becomes warped of physically damaged. ~ During setup, make sure that all the screws are securely tightened. ~ Ensure that the TV does not suffer any impact during the attachment of the stand. - Ensure that children do not climb onto the stand. - Attach or remove the stand with at least two people. 106m Prevent small items from getting into the interior of the device through the ventilation slots. Such objects may cause short circuits, which may cause fire. If something should get inside the unit, immediately unplug the power plug of the device and contact service support. m@ The screen Despite thorough care when manufacturing this display, it cannot be 100% guaranteed that no sub-pixel defects will occur due to technical reasons. These cannot be considered as a device defect in terms of the guarantee. They will not affect the performance and reliability of the TV. To prevent “image bum’, avoid displaying still images for long periods of time, there is a possibility that a copy of the image may remain. If the aspect ratio is set to 4:3 for a long period of time, image bum may occur on the black areas. Image burn is not covered by the warranty. ~ Do not apply strong force or impact on the display panel Avoid touching the screen or touching it for long periods of time. Doing so may produce some temporary distortion effects on the screen. m@ Radio waves - Do not use the TV in any medical institutions or locations with medical equipment. Radio waves may interfere with medical equipment and cause malfunction. - Do not use the TV near any automatic control equipment such as automatic doors or fire alarms. Radio waves may interfere with automatic control equipment and cause malfunction.os | Ifyou have a cardiac pacemaker, keep a distance of at least 22 cm from the TV. Radio waves may interfere with the operation of a pacemaker. @ Built-in wireless LAN ~ Do not connect to wireless networks that you do not have the usage rights for. Data transmitted and received over radio waves may be intercepted and monitored. The built-in wireless LAN uses 2.4 GHz and 5 GHz frequency bands. To avoid malfunctions or slow response caused by radio wave interference, keep the TV away from devices such as other wireless LAN devices, microwaves, mobile phones, and other devices that use 2.4 GHz and 5 GHz signals. @ Warning about off-gassing New furniture, carpet, paint, building materials and electronics can release chemicals into the air through evaporation. After you set your TV up and turn it on for the first time, you may notice a slight smell within a couple of hours. This is because some components of TV are heating up for the first time. The materials that we use fully meet the environmental requirements and regulations. Your TV is working just fine and the fumes from the off-gassing will diminish eventually. @ Supervision ~ Do not let children play unsupervised close to the TV. It could tip over, be pushed off or pulled down from the stand surface and injure someone. - Do not allow a switched-on TV to run unattended. @ Volume Loud music and noises can lead to irreversible damage to your ears. Avoid ‘extreme volume, especially over long periods and when using headphones. If you hear a drumming noise in your ears, turn down the volume or temporarily stop using headphones. @ Thunder Storms Pull out the power plug and all connected antenna cables from the TV during a thunderstorm. Overvoltage caused by lightning strikes can damage the TV via the antenna system, as well as the wall socket. ™@ Long periods of absence As long as the power plug is connected to a live socket outlet, the TV will consume power even in standby mode. The power plug and all connected antenna cables should be disconnected out during long periods of absence.| | ™@ Cleaning and care CAUTION: Unplug the power cord prior to cleaning the TV. Clean the TV, the screen, and the remote control with a soft, moist, clean and color-natural cloth only. Do not use any chemicals. - Do not subject the surfaces to insect repellent, solvent, thinner or other volatile substances. This may degrade the surface quality. Do not spray water or other liquids directly on the TV. Liquid inside the TV could lead to product failure. The surface of the display panel is treated and may be easily damaged Take care not to scratch it with fingernails or other hard objects. Also wipe the power plug with a dry cloth at regular intervals. @ Service/Repair Never remove the cover/back of the TV; there are no user serviceable parts inside. Refer all service to qualified service personnel @ Packaging Keep the anti-moisture materials and Plastic bags out of reach of children. Plastic bags can cause suffocation and the anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. @ Modification Do not attempt to modify this product in any way. Unauthorized modification could void the warranty of this unit, cause electric shock and fires. m@ Remote Control batteries Incorrect installation may cause battery leakage, corrosion and explosion - Replace only with the same or equivalent type. - Do not mix old and new batteries. - Do not mix different battery types. - Do no use rechargeable batteries. Do not burn or break up batteries. Be sure to dispose of batteries correctly. - Do not expose batteries to excessive heat such as sunshine, fire or the like. @ Outdoor Antenna Grounding If an outdoor antenna used, be sure the antenna system is protected against voltage surges and built-up static charges. — Disposal Refer to the recycling section of this manual. SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Hisense Czech s.r.o declares that the radio equipment type [ERF6A62/ ERF6C62H/ERF6A64/ERF6B64H/55U8QF/55U81 QF/5S5U82QF/S55U8QFTUK/65U 8QF/65U81QF/65U82QF/65U8QFTUK] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://global.hisense.com/downloads.Apparatus with CLASS | construction shall be connected to a MAINS socket outlet with a protective earthing connection. (only for 65") Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Parts of the software function changes with the system upgrade. Contents Accessories List.... Installing the Stand or Wall mount bracket... TV Front... TV Rear... Making Connections... Remote Control .... Turning the TV on for the First Time Specifications Other Information. Accessories List The following accessories are included with TV: User Manual * 1 Warranty Card x 1 Power Cord x 1 Base Stand x 1 Screw x 7 Remote Control x 1 AAA Battery x 2 BINOTE - The accessories may be different from the list above due to different models, countries / regions, please refer to the actual accessory bag.Sea: | aL > Installing the Stand © CAUTION Be sure to disconnect the A/C power cord before installing a stand or Wall-Mount brackets. The screen is very fragile, and must be protected at all times when installing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the screen, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the screen could crack. After the installation is complete, make sure the TV is steady on a table or firmly attached to a wall mount, before removing all protective film, if any. Follow the illustrations and textual instructions below to complete the installation steps: 1. Carefully place your TV face-down on a soft, flat surface to prevent damage to the TV or scratching to the screen 2. Raise the bottom of the Base Cover, take it off and put it aside. The place that the Base Cover is at is used for fixing the base. raise the Base Cover 5 3. Using the 3 screws in the accessory bag, secure Part A, Part B and Part C as the following figure shows. Screws: M5x16Installing th Tae 4, Secure the Base Stand to the TV with the 4 screws in accessory tightly. ~-Base Cover > Installing the wall mount bracket 400 x 300 (55") 400 x 400 (65") Wall mount screw size (mm) M6 8.0-100mm Wall mount hole pattern (mm) Wall Mount Bracket Wall Mount Screw Rear cover of the TV Wall Mount Spacer Follow instructions provided with the wall mount bracket. BINOTES * The diameter and length of the screws differ depending on the wall mount bracket model. * Wall mount bracket is optional, your device may not have wall mount bracket, please refer to the actual accessories.TV Front Single button (Remote sensor / Power indicator / Standby) Item Description Remote sensor Power indicator Receive remote signals from the remote control. Do not put anything near the sensor, as its function may be affected. The light is red in standby mode. & Standby / Source BINOTES Press the single button when in standby mode, TV will be turned on. Press the single button to call up the menu, when the focus is on "Power Off", wait for 3 seconds, then the TV will go into standby mode automatically. / Press the single button to call up the menu and then select among the different input signal sources. The Picture is Only for Reference. Powering on the TV requires several seconds to load programs. Do not rapidly turn the TV off as it may cause the TV work abnormally.TV Rear nm z . & a i é 3 . u oO oO ge ‘AC INPUT a 8 SOOO) |. Cine iS be g BINOTES + ANT2 Jack supports power supply for satellite antenna (13/18V, 0.54 max.) Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure. Not all A/V devices have the ability to connect to a TV, please refer to the user's manual of your A/V device for compatibility and connections procedure. ) Before connecting external equipment, remove the mains plug from the wall socket. Otherwise, it may cause electric shock, i i 5 i AK) BS us? oc:> LAN (Wired setup) Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Ethernet/Cat 5) cable. See the illustration below. We recommend to use a modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS, so you don't have to enter them manually. Most home networks already have DHCP. TV JACK IP Sharer (Router) External Modem a (with DHCP server) (ADSL / VDSL / Cable TV) LAN [iA : : See es LAN Cable LAN Cable Modem Cable Wireless setup Connect your TV to your network wirelessly, you need a wireless router or modem See the illustration below. + The built-in Wireless LAN Adapter supports the IEEE 802.11a/b/g/n/ac communication protocols. We recommend using IEEE 802.11n router. Low transfer rates for b/g may have the influence on the quality of streamed videos and other media. ( y Wireless LAN Adapter builtin TV set _—————| ——__——— BINOTES You must use the built-in Wireless LAN Adapter to use a wireless network because the set doesn’t support external USB network adapter. If the wireless router supports DHCP, your TV can connect more easily to the wireless network. If you apply a security system other than the systems listed below, it will not work with the TV. Security system: WPA, WEP,WPA2 In order to guarantee smooth network, the distance between router and TV should be less than 10 meters.Outdoor atonna ant 7 ovearTae ‘Antenna Cable (750) (not included) VHF/UHF Antenna ANT ant oes (rot included) Satelite antenna a Audio Amplifier/Speaker DIGITAL A58O0T gp rt AUDIO OUT 9 DIGITAL AUDIO cable (not included) Hp on Audio Amplifier/Speaker (ARC) S {»———_g@ {= ae HDMI cable (not included) HDMI DVD/Blu-Ray/AV receiver! tow Set-top Box HDMI S Ss HDMI cable (not included) 1 Red(R) VCRIDVD Player! 9° RecorderiSet-top box! le White(L) Satellite Receiver! AVIN © a Video Camera Yellow(Video) ar of (ideo) ere (Cables are not included)BINOTES Before you insert/remove the Cl+ module, ensure that the TV is switched off. Then insert the Cl card into the Cl+ module in COMMON accordance with the Service Provider's instructions. INTERFACE Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction. You must obtain a Cl+ module and card from the service provider of the channels you want to watch. Insert the Cl+ module with the SmartCard in the direction marked on the module and SmartCard. Cl+ is not supported in some countries and regions; check with your authorized dealer. ce seen E> BINOTES When connecting a hard disk or a USB hub, always connect USB the mains adapter of the connected device to the power supply. Exceeding a total current consumption may result in damage. The USB1.1 and USB2.0 devices maximum current consumption are 500mA. For individual non-standard high-capacity mobile hard disk, if its impulse current is greater than or equal 1A, it may cause TV-rebooting or self-locking. So the TV does not support it. + The USB port supports a voltage of 5V.@ ® ® ©®o oe @® © ©8e@ © © © QG@OO® SOGOOSSGSOGS OOOO © © OOO @ POWER: Switch the TV on or into standby mode INPUT: Select input sources TEXT: Turn on/off the teletext function Number button: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.List: Display the Channel List on the screen Special function buttons Display the Quick setup menu Media content control function buttons Alv/<1>: Allows you to navigate the OSD menus and adjust the system settings to your preference OK: Confirm the selection in the OSD menus Retum to previous menu EXIT: Exit the menu HOME: Enter the Smart VOL —*/=2: Adjust the volume CHA/\:: Switch channel MUTE: Mute or restore the TV sound ick access buttons to apps All Apps. Media: Enter the media mode Voice command Quick access buttons to apps Receive the voice Bluetooth remote control module specifications WNF 171 Frequency Range: 2.402~2.480GHz Output Power(Max.): +4.5dBm NOTE: The included remote control will vary depending ‘on model, country. Check information according to the actual remote control in the accessory bag© 608 ® 98 © ® 0© OOO 90 © © ©8008 0 QOOGSOGOOSO OOO ® POWER: Switch the TV on or into standby mode INPUT: Select input sources INFO: Display the present program information All Apps. Custom button to launch input or apps quickly Number button: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.List: Display the Channel List on the screen Display the Quick setup menu Special function buttons Alv1: Allows you to navigate the OSD menus and adjust the system settings to your preference OK: Confirm the selection in the OSD menus Retum to previous menu Media content control function buttons HOME: Enter the Smart VOL —*/ = : Adjust the volume CH A/~: Switch channel MUTE: Mute or restore the TV sound ‘TXT: Tum on/off the teletext function Sub.: Activate or deactivate the subtitle mode Voice command Quick access buttons to apps Media: Enter the media mode Receive the voice Bluetooth remote control module specifications WNF150 Frequency Range: 2.402~2.480GHz Output Power(Max.): +4dBm NOTE: The included remote control will vary depending on model, country. Check information according to the actual remote control in the accessory bag. 10INFO | INPUT © © ©8808 © QOOGSOGOOGSO OOO POWER: Switch the TV on or into standby mode INPUT: Select input sources INFO: Display the present program information All Apps. Custom button to launch input or apps quickly Number button: Direct channel selection or numbers input GUIDE: Display the Electronic Program Guide (DTV mode) CH.List: Display the Channel List on the screen Display the Quick setup menu Special function buttons Alv1<1>: Allows you to navigate the OSD menus and adjust the system settings to your preference OK: Confirm the selection in the OSD menus Retum to previous menu Media content control function buttons HOME: Enter the Smart VOL —*/ == : Adjust the volume CH A/~: Switch channel MUTE: Mute or restore the TV sound ‘TXT: Tum on/off the teletext function ‘Sub.: Activate or deactivate the subtitle mode P.Mode: Picture Mode button Quick access buttons to apps Media: Enter the media mode NOTE: The included remote control will vary depending on model, country. Check information according to the actual remote control in the accessory bag.> Installing Batteries in the Remote Control NOTE: Check information according to the actual remote control in the accessory bag. . Slide the back cover to open the battery compartment of the remote control. 2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. 2 . Close the battery compartment with the cover. . Press the switch and the battery case will pop up automatically. 2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+) and ( - ) ends indicated in the battery compartment. Push the battery case back to the remote control. 2 BINOTES Product image is only for reference, actual product may vary in appearance. Handling the Batteries Incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property. Only use the battery type indicated in this manual. Do not mix old and new batteries or different types of batteries. Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations. v Remote Control Operation RangeTurning the TV on f Turning the TV on for the First Time 1. Connect the mains cable to the mains socket after you have completed all the connections. 2. The first time you turn the TV on, it will go straight into the Installation Guide. 3. Press the [a/v / ] buttons to navigate the menu and change the settings. Press the [OK] button to confirm. Select your desired language to be displayed on the menu. Select “Home Mode” or “Store Mode”. If your TV does not automatically detect an Ethernet connection, then use a wireless network, select your network from the list that displays, also you can add a hidden network. When you're done, move to the next screen. Select the Country where you will operate the TV. Select the local time zone according to your region. Your use of this device is subject to the End User License Agreement, lack of your acceptance of the End User License Agreement will turn off all smart features of this device. You can choose to turn on/off each type of smart features separately, a click to the box of each type of smart feature means you give your consent to the corresponding privacy notice/terms and conditions. Enhanced viewing can automatically adjust the picture mode and sound mode so as to match with the current content displayed ‘on this device in case it is recognized by the automatic content recognition service. (This function is only applicable in certain models/countries.) Link your TV with VIDAA account.ee @ Features, appearance and specifications are subject to change without notice. Item 55" 65" x x x x Dimension in |rnncumieeannc (tos vr : enn) (has 2 382 08 ae ° (W x H x D) x x in x x eH eO) nse SS Sse fT on ano Weight Without Stand | 38.4 lbs (17.4 kg) 54.7 Ibs (24.8 kg) With Stand 41.7 lbs (18.9 kg) [60.0 }bs (27.2 kg) Active Screen Size (Diagonal) | 139 cm 164 cm Screen resolution 3840 x 2160 3840 x 2160 Operating mode power density 0.0316 Watts/cm? 0.0261 Watts/cm? Power consumption when turned off = < 0.5 W <0.5W Power consumption in standby mode | 0.5 W 0.5W Audio power 10W + 10W 10W + 10W Power consumption Please refer to the rating label. Power supply Please refer to the rating label. Receiving _| Analog PAL-D/K, B/G, |, SECAM-D/K, B/G systems Digital DVB-T/T2, DVB-C, DVB-S/S2 Model WF-M68A-UWF1 Frequency 2.4~2.4835GHz Range 5.15~5.85GHz yea 2.4~2.4835GHz 17dBm specifications 5.15~5.25GHz 15dBm Output Power §.25~5.35GHz(DFS Band) 14dBm (Max.) 5.49~5.71GHz(DFS/TPC Band) 13dBm 5.725~5.85GHz(for Non EU) 13dBm Model WF-M68A-UWF1 Bluetooth —_| Frequency Module Range 2.4~2.4835GHz specications Output Power (Max.) 2.4~2.4835GHz, Class1, 5dBm Environmental conditions Temperature: 41°F - 95°F (5°C - 36°C) Humidity: 20% - 80% RH Atmospheric pressure: 86 kPa - 106 kPaSpecifications RGB / 60 Hz (640480, 800x600, 1024x768) YUV / 60 Hz (480 I, 480 P, 720 P, 1080 I, 1080 P) HDMI Input YUV / 5OHz (576 |, 720 P, 1080 I, 1080 P) F 3840x2160 / 24Hz, 3840x2160 / 25Hz 3840x2160 / 30Hz, 3840x2160 / 50Hz, 3840x2160 / 6OHzRecycling/Licenses WEEE (Waste Electronic Electric Equipment) European Directive 2012/19/EU Batteries This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, itis your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that itis recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. In accordance with the Battery Directive, used batteries should not be disposed of in the domestic waste. Dispose your batteries in the collection containers specific for this purpose in retail stores. ROHS (Restriction of Hazardous Substance) European Directive 2011/65/EU Hom DOLBY VISION «ATMOS. This European directive limits the use of dangerous and hazardous substances which are difficult to recycle. This allows recycling easily the EEE and contributes to the safeguard of the environment. Substances included in this product match to the RoHS directive. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing ‘Administrator, Inc. in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Dolby Atmos, Dolby Vision, and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2019 Dolby Laboratories. Allrights reserved.