Jenbacher 4.

1
Documentation Checklist for alarm messages

General:
When the installation is operational, the engine management system DIANE will not only control the
engine but will also perform engine-failure management. The engine-failure management system checks
all relevant system variables and will issue a warning or switch off the installation if certain set values are
exceeded or underrun.

Remedying and resetting failures:

When a failure results in the installation being switched off, the cause of the failure should be
remedied first before the installation is started again. When a failure results in a warning being
issued, the cause of the failure should be remedied first before the failure is reset.

Turn off motor according to technical instruction no. 1100-0105 and secure against unauthorized
restart.

It is forbidden simply to reset a failure and then start the engine again!

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 1 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

Table of contents

10 START CONDITIONS MISSING

- OF MOTOR
- OF AGGREGATE
- OF THE UNIT
20 MOTOR WON'T START
30 MOTOR SAWING IN IDLE RUN (can't be synchronized)
40 MOTOR DOES NOT REACH FULL LOAD (while maintaining the guaranteed pollutant
emissions)
50 MOTOR OR SYSTEM MOTOR/GENERATOR RUNS IRREGULARLY OR UNSTABLE
WITH LOAD
- MOTOR VIBRATES STRONGLY
- MOTOR SHAKES (quick load fluctuations or great current and voltage fluctuations with little
change of motor output)
- GENERATOR MOTOR ESCALATES (great current and voltage fluctuations at only little
change in motor output)inger ve
- GENERATOR MOTOR ESCALATES (great current and voltage fluctuations at only little
change in motor output)
- MOTOR ARCHIEVES NOT STABLE CONDITION (output swings slowly up and down)
- ENGINE STOPS (individual cylinders) OR HAS AN EXHAUST GAS TEMPERATURE
DEVIATING FROM THE CENTRAL VALUE
- PERIODIC FLUCTUATIONS IN PERFORMANCE
60 Motor knocking
70 MISFIRING DETECTION RESPONDS, OR AT BR6 DEVIATION OF CYLINDER FLUE
GAS TEMPERATURE TOO GREAT
90 OIL CONSUMPTION TOO HIGH
100 TURBOCHARGER DEFECT
- COMPACTOR THROWING OIL
- TURBINE THROWING OIL
- TURBOCHARGER EFFICIENCY NOT OKAY (flue gas turbocharger no longer archieves
required load pressure)
- COMPACTOR OR TURBINE WHEEL TOUCHED THE HOUSING
- TURBOCHARGER VIBRATING
110 WATER IN LUBRICATION OIL
120 THE CONTRACTUALLY AGREED DEGREE OF EFFICIENCY IS NOT REACHED IN
SPITE OF THE SALES TOLERANCE
1001 FUEL-SKID FAULT
1017 OIL PRESSURE LOW
1018 ENGINE OIL LEVEL LOW
1019 JACKET WATER PRESSURE LOW
1021 JACKET WATER TEMPERATURE HIGH
1022 OVERSPEED (RELAY)
1023 START UP FAILURE
1024 START CONDITIONS MISSING
1025 ENGINE OPERATION CONDITIONS MISSING
1026 SHUTDOWN FAILURE
1027 FAILURE GAS TRAIN 1
1028 GAS PRESSURE LOW IN GAS TRAIN 1
1031 EMERGENCY STOP/SAFETY LOOP

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 2 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1036 GENERATOR OVERLOAD/SHORT CIRCUIT

1038 GENERATOR REVERSE POWER
1039 SYNCHRONIZING FAILURE
1040 FUEL MIXTURE TEMPERATURE HIGH
1041 POWER SIGNAL MISSING
1042 POWER SIGNAL OVERLOAD
1043 ENGINE OIL TEMPERATURE HIGH
1047 MISFIRING FAILURE
1048 KNOCKING FAILURE
1050 JACKET WATER PRESSURE HIGH
1051 ENGINE OIL LEVEL HIGH
1052 GAS PRE-ALARM
1053 GAS ALARM
1054 FIRE ALARM
1056 FAIL SAFE LOOP TRIPPED
1059 OIL FILTER DIFFERENTIAL PRESSURE HIGH
1060 PRE-LUBE PRESSURE LOW
1061 IGNITION SYSTEM FAILURE
1064 OVERSPEED (RPS-CONTROL SYSTEM)
1078 BOOST PRESSURE MEASURING SIGNAL FAILURE
1080 LEANOX CONTROL ALLOWED DEVIATION EXCEEDED
1081 KNOCK SENSOR MEASURING SIGNAL FAILURE
1083 CONTROL CARBURATOR DEFECTIVE
1096 MULTI MEASUREMENT DEVICE CAN COMMUNICATION FAILURE
1101 TRANSFORMER FAILURE
1105 SPEED OF TEMPERATURE CHANGE MIXTURE TEMPERATURE MAXIMUM
1108 DEVIATION POWER SETPOINT TO POWER PRESENT VALUE MAXIMUM
1109 GENERATOR LOSS OF EXCITATION
1110 GENERATOR FREQUENCY TOO LOW
1111 GENERATOR FREQUENCY TOO HIGH
1112 NEUTRAL CURRENT MAXIMUM
1113 GENERATOR POWER MEASURING SIGNAL FAILURE
1114 FUEL MIXTURE TEMPERATURE MEASURING SIGNAL FAILURE
1120 SPEED MEASURING SIGNAL FAILURE
1121 GENERATOR WINDING (L1) TEMPERATURE HIGH
1122 GENERATOR WINDING (L2) TEMPERATURE HIGH
1123 GENERATOR WINDING (L3) TEMPERATURE HIGH
1124 GENERATOR BEARING (A) TEMPERATURE HIGH
1125 GENERATOR BEARING (B) TEMPERATURE HIGH
1126 GENERATOR VOLTAGE LOW
1127 GENERATOR VOLTAGE HIGH
1129 FAILURE WITH AUXILIARIES
1135 ROOM TEMPERATURE HIGH
1140 MODULE INTERFACE PANEL CIRCUIT BREAKER TRIPPED
1143 VOLTAGE NEGATIVE SEQUENCE
1144 CURRENT NEGATIVE SEQUENCE
1145 JACKET WATER TEMPERATURE LOW
1148 STARTER BATTERY VOLTAGE LOW
1153 CYLINDER EXHAUST GAS TEMPERATURE MEASURING SIGNAL FAILURE
1154 GENERATOR WINDING (L1) TEMPERATURE HIGH

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 3 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1155 GENERATOR WINDING (L2) TEMPERATURE HIGH

1156 GENERATOR WINDING (L3) TEMPERATURE HIGH
1157 GENERATOR BEARING (A) TEMPERATURE HIGH
1158 GENERATOR BEARING (B) TEMPERATURE HIGH
1159 FRESH OIL TANK LEVEL LOW
1160 WASTE OIL TANK LEVEL HIGH
1168 REQUEST FOR MAINTENANCE
1176 AIR INLET FILTER DIFFERENTIAL PRESSURE HIGH
1177 SPARE TEMPERATURE MEASURING SIGNAL FAILURE
1188 RELEASE FROM PLANT MANAGEMENT SYSTEM MISSING
1189 RELEASE FROM SYNCHRONIZING MISSING
1192 ACTUATOR FAILURE
1193 FEED BACK BOOSTER MISSING
1194 FEED BACK FUEL-SKID MISSSING
1195 OPENING FAILURE OTHER GENERATOR C.B.
1216 BUS BAR VOLTAGE SENSOR FAILURE
1217 GENERATOR CB STATUS SIGNAL FAILURE
1218 GENERATOR CB OPENING FAILURE
1219 GENERATOR CB CLOSING FAILURE
1220 GENERATOR CB O-SIGNAL FAILURE
1221 GENERATOR CB 1-SIGNAL FAILURE
2061 CYL. 1 MEASURING SIGNAL FAILURE
2062 CYL. 2 MEASURING SIGNAL FAILURE
2063 CYL. 3 MEASURING SIGNAL FAILURE
2064 CYL. 4 MEASURING SIGNAL FAILURE
2065 CYL. 5 MEASURING SIGNAL FAILURE
2066 CYL. 6 MEASURING SIGNAL FAILURE
2067 CYL. 7 MEASURING SIGNAL FAILURE
2068 CYL. 8 MEASURING SIGNAL FAILURE
2069 CYL. 9 MEASURING SIGNAL FAILURE
2070 CYL. 10 MEASURING SIGNAL FAILURE
2071 CYL. 11 MEASURING SIGNAL FAILURE
2072 CYL. 12 MEASURING SIGNAL FAILURE
2073 CYL. 13 MEASURING SIGNAL FAILURE
2074 CYL. 14 MEASURING SIGNAL FAILURE
2075 CYL. 15 MEASURING SIGNAL FAILURE
2076 CYL. 16 MEASURING SIGNAL FAILURE
2077 CYL. 17 MEASURING SIGNAL FAILURE
2078 CYL. 18 MEASURING SIGNAL FAILURE
2079 CYL. 19 MEASURING SIGNAL FAILURE
2080 CYL. 20 MEASURING SIGNAL FAILURE
2082 PARAMETER(S) FROM DISPLAY UNIT (USER INTERFACE) MISSING
2083 RPS (CONTROL SYSTEM) BATTERY FAILURE
2084 LEANOX ALGORITHM FAILURE
2086 CARBURATOR POSITION MEASURING SIGNAL FAILURE
2097 DEVIATION POWER SETPOINT TO POWER PRESENT VALUE MAXIMUM
2101 JACKET WATER TEMPERATURE MEASURING SIGNAL FAILURE
2102 ENGINE OIL TEMPERATURE MEASURING SIGNAL FAILURE
2103 ENGINE OIL PRESSURE MEASURING SIGNAL FAILURE
2104 JACKET WATER PRESSURE MEASURING SIGNAL FAILURE

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 4 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

2106 GENERATOR WINDING TEMPERATURE L1 MEASURING SIGNAL FAILURE

2107 GENERATOR WINDING TEMPERATURE L2 MEASURING SIGNAL FAILURE
2108 GENERATOR WINDING TEMPERATURE L3 MEASURING SIGNAL FAILURE
2109 GENERATOR BEARING (A) TEMPERATURE MEASURING SIGNAL FAILURE
2110 GENERATOR BEARING (B) TEMPERATURE MEASURING SIGNAL FAILURE
2116 DUMP RADIATOR FAILURE
2117 INTERCOOLER WATER PRESSURE LOW
2118 MALFUNCTION OF MIXTURE COOLING WATER PUMP
2120 ENGINE ROOM VENTILATION FAILURE
3003 MEASURING SIGNAL FAILURE
3025 IGNITION TRIGGER PICKUP MISSING
3026 IGNITION RESET PICKUP MISSING
3027 IGNITION CAM PICKUP MISSING
3028 IGNITION SHUTOFF OVERSPEED
3029 IGNITION CPU FAILURE
3030 IGNITION PARAMETER FAILURE
3031 IGNITION CAN COMMUNICATION FAILURE
3032 IGNITION OUTPUT MONITORING CYLINDER 1
3033 IGNITION OUTPUT MONITORING CYLINDER 2
3034 IGNITION OUTPUT MONITORING CYLINDER 3
3035 IGNITION OUTPUT MONITORING CYLINDER 4
3036 IGNITION OUTPUT MONITORING CYLINDER 5
3037 IGNITION OUTPUT MONITORING CYLINDER 6
3038 IGNITION OUTPUT MONITORING CYLINDER 7
3039 IGNITION OUTPUT MONITORING CYLINDER 8
3040 IGNITION OUTPUT MONITORING CYLINDER 9
3041 IGNITION OUTPUT MONITORING CYLINDER 10
3042 IGNITION OUTPUT MONITORING CYLINDER 11
3043 IGNITION OUTPUT MONITORING CYLINDER 12
3044 IGNITION OUTPUT MONITORING CYLINDER 13
3045 IGNITION OUTPUT MONITORING CYLINDER 14
3046 IGNITION OUTPUT MONITORING CYLINDER 15
3047 IGNITION OUTPUT MONITORING CYLINDER 16
3048 IGNITION OUTPUT MONITORING CYLINDER 17
3049 IGNITION OUTPUT MONITORING CYLINDER 18
3050 IGNITION OUTPUT MONITORING CYLINDER 19
3051 IGNITION OUTPUT MONITORING CYLINDER 20
3052 WRONG TYPE OF IGNITION SYSTEM
3152 ENGINE ROOM TEMPERATURE MEASURING SIGNAL FAILURE
3153 RELEASE FROM GAS PLANT MISSING
3155 CH4 CONTENT MEASURING SIGNAL FAILURE
3158 O2 CONTENT MEASURING SIGNAL FAILURE
3209 IGNITION SETTING IS FORBIDDEN DURING THE ENGINE IS RUNNING
3216 ENGINE OIL TEMPERATURE HIGH
3217 MISFIRING FAILURE
3218 OIL PRESSURE LOW
3219 EXCITATION VOLTAGE LOW
3220 JACKET WATER TEMPERATURE HIGH
3221 GAS PRESSURE LOW IN GAS TRAIN 1
3223 INTAKE AIR TEMPERATURE HIGH

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 5 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3224 INTAKE AIR TEMPERATURE MEASURING SIGNAL FAILURE

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 6 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

Cause Remedy Advice

10 START CONDITIONS MISSING

--- - ---

- OF MOTOR
There is a defect as e.g. min. or max. remove indicated cause remove ---
oil level. loose contact or wire breakage, or
The current loop (safety loop) is open replace defective monit. device.

- OF AGGREGATE
e.g. min. gas pressure closed current remove cause or complain at ---
loop not released trader;remove loose contact or wire
breakage, or replace defect
monitoring device

- OF THE UNIT
e.g. min. gas pressure closed current check which auxiliary operation is not ---
loop not released running, e.g. HW-circulation pump or
throughflow indicator and machine
room vent flap open, gas warning
installation etc.

20 MOTOR WON'T START

gas magnet valve is defective check whether gas magnet valves ---
open

30 MOTOR SAWING IN IDLE RUN (can't be synchronized)

Gas-pressure fluctuations use manometer or water columnto ---
Check the control rods (ball heads measure where the gas pressure
worn / sluggish) fluctuations appear, i.e., upstream of
Mixture too lean / too rich mixer, upstream of gas pressure
Check speed controller setting controller or downstream of
customergas admission controller; if
controller unsuited, replace it, or call
supplier (of admission pressure
controller).

40 MOTOR DOES NOT REACH FULL LOAD (while maintaining the guaranteed pollutant
emissions)
combustion air ratio not okay, motor correct leanox adjustment at DIANE ---
too lean (NOx value too low)

50 MOTOR OR SYSTEM MOTOR/GENERATOR RUNS IRREGULARLY OR UNSTABLE WITH

LOAD
- - ---

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 7 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

- MOTOR VIBRATES STRONGLY

failure of cylinder check ignition, valves, check see maintenance
compression

- MOTOR SHAKES (quick load fluctuations or great current and voltage fluctuations with
little change of motor output)
faulty ignition check ignition system see maintenance

- GENERATOR MOTOR ESCALATES (great current and voltage fluctuations at only little
change in motor output)inger ve
misfires (motor adjusted too lean) check and adjust with pollutant ---
measuring device check, adjust

- GENERATOR MOTOR ESCALATES (great current and voltage fluctuations at only little
change in motor output)
voltage controller at generator not adjust or repair description -
okay check cables generator
cos phi controller not okay check that connector is firmly located
bad connection in circuit (cables)

- MOTOR ARCHIEVES NOT STABLE CONDITION (output swings slowly up and down)
Non-optimal setting of Leanox-control optimise the controller parameters at ---
parameters constant power setpoint
Check control rods (ball heads worn /
sluggish)
Check gas pressure
Check power control
Check gas-quality fluctuations (landfill
gas, possibly sewage gas)

- ENGINE STOPS (individual cylinders) OR HAS AN EXHAUST GAS TEMPERATURE

DEVIATING FROM THE CENTRAL VALUE
defective ignition check see maintenance

- PERIODIC FLUCTUATIONS IN PERFORMANCE

continual switching on and off of the Conversion to thermostatically- ---
ventilator(s) controlled, frequency-regulated
ventilator

60 Motor knocking
combustion air ratio not okay check, correct adjustment if Schematic diagram
necessary

70 MISFIRING DETECTION RESPONDS, OR AT BR6 DEVIATION OF CYLINDER FLUE GAS

TEMPERATURE TOO GREAT
motor misfires because it is set too check using an exhaust emmissions ---
lean or due to defective ignition analyser and correct if necessary

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 8 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

90 OIL CONSUMPTION TOO HIGH

turboloader throwing oil see point 0100 ---

100 TURBOCHARGER DEFECT

- - -

- COMPACTOR THROWING OIL

air filter resistance too great (dirty clean air filter, if required replace see maintenance
filter)

- TURBINE THROWING OIL

oil sealing at turbine is defective check and repair ---

- TURBOCHARGER EFFICIENCY NOT OKAY (flue gas turbocharger no longer archieves

required load pressure)
entrance shovels of compactorare check, search cause (foreign body?) ---
defective or damaged and replace FGTL if necessary

- COMPACTOR OR TURBINE WHEEL TOUCHED THE HOUSING

defective axial sealing -axial play too measure in case of exceeding ---
great admissible value repair or replace.

- TURBOCHARGER VIBRATING
turbine shovels (compactor shovels) replace wheel or turboloader ---
defective (unbalanced)

110 WATER IN LUBRICATION OIL

leaky O-rings at the cylinder liner replace O-rings ---

120 THE CONTRACTUALLY AGREED DEGREE OF EFFICIENCY IS NOT REACHED IN SPITE

OF THE SALES TOLERANCE
on site the sum of border conditions measure values exactly and convert ---
is strongly negative in order to reach to standard condition according to
an optimal efficiency (e.g. heating ISO 3046
value of depot gas extremely low,
induction temperature >25°C, air
pressure <1000 mbar)

1001 FUEL-SKID FAULT

Signal from customer Repair customer's gas cleaning ---
Customer's gas cleaning system system
defective Replace digital module
Defective digital input or digital input
module

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 9 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1017 OIL PRESSURE LOW

leak in the oil lines or the oilpan eliminate cause! ---
clogged oil cooler, oil filter or oil line
uncontrolled switching off (killing) of
engine too low speed
oil level below "min. oil level"
defective oil pressure transmitter
engine switch-off by closed current
loop (defect monitoring)
wrong adjustment of fringe value

1018 ENGINE OIL LEVEL LOW

leakage in oil lines or oilpan eliminate cause! ---
defective solenoid valve "fill oil" (won't
open)
defective oil level sensor or
evaluation device
empty fresh oil tank
slide at oil pump station is closed
three-way cock in wrong position
oil level measurerer not adjusted
(with analog measuring)
"sag" in pressure-equalization line
(venting)
wrong adjustment of fringe value

1019 JACKET WATER PRESSURE LOW

leak in cooling water system eliminate cause! ---
defective pressure transmitter of
cooling water
leaking safety valve
damaged membrane in pressure
wrong adjustment of fringe value
crack in inlet or outlet duct of cylinder
head

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 10 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1021 JACKET WATER TEMPERATURE HIGH

hot water feedback temp. too high eliminate cause! ---
cooler clogged, calcified, dirty
return temperature control incorrectly
adjusted
emergency cooler clogged calcified,
dirty
fresh water missing
cool. wat. pump defect
defect. cool. water temp.
transmission
heat circulation pump defective
heat circ. slide, fresh - water slide
closed
ambient temp. too high (with table
cooler)
throughflow amount too small
(primary/secondary)
follow-up heating when shut off
water circulations not vented
motor output too high
glycool amount too high
defective short-circuit thermostat
wrong adjustment of fringe value
water circulation not vented

1022 OVERSPEED (RELAY)

wrong adjustment of or defective eliminate cause! ---
speed controller
stuck or bent throttle flap
speed relay defective or wrongly
adjusted
Minimum throttle opening set too
wide eg. throttle valve bent

1023 START UP FAILURE

3 unsuccessful starting attempts no eliminate cause! ---
gas
defective ignition
wrong gas mixer valve start position
wrong adjustment of gas pressure
safety automation in motor terminal
strip is off
starter won't start

1024 START CONDITIONS MISSING

no release by auxiliary plants during eliminate cause! ---
engine operation

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 11 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1025 ENGINE OPERATION CONDITIONS MISSING

release through auxiliary operation eliminate cause! ---
does not apply while the engine is
running - i.e. indication hot water
pump on
indication mixture cooling-water
pump on
release, gas tightness test
engine max. oil level not indicated
indication customer side auxiliary
operation on
boiler valve or boiler bypass valve or
both valves open

1026 SHUTDOWN FAILURE

leaky or defective gas valves eliminate cause! ---
speed limit wrongly adjusted

1027 FAILURE GAS TRAIN 1

leaky gas valves eliminate cause! TI 1000-0300
gas valve closed
defective gas tightness coantroller
clogged gas filter
too low gas pressure
dirty filter in supply line to tightness
controller
condensate in the supply line to
tightness controller
vibrations of tightness controller
device

1028 GAS PRESSURE LOW IN GAS TRAIN 1

gas valve closed eliminate cause ! TI 1000-0300
wrong adjustment or defective gas
pressure controller
missing gas supply (line breakage)
pressure fluctuations by other user
defective pressure switch
no gas present (sewer gas)
wire breakage to PLC
dirty filter in supply line

1031 EMERGENCY STOP/SAFETY LOOP

emergency off button enabled eliminate cause ! ---
wire breakage
safety loop
belt alarm --> when in emergency off
chain
gas alarm --> linked

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 12 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1036 GENERATOR OVERLOAD/SHORT CIRCUIT

wrong adjustment or defective output eliminate cause! ---
controller
overload in isolated operation
short circuit
wrong adjustment or defective output
switch
wrong adjustment or defective cos-
phi controller
wire breakage to PLC
unbalanced load

1038 GENERATOR REVERSE POWER

generator power switch does not eliminate cause! ---
open
10% power switch point wrong
adjustment
output reduced too quickly
defective output measurement (only
variant with reverse current relay)
wrong adjustment rev. current relay
or defective
DIANE wrong adjustment or defective
defective current transmitter
wire breakage to PLC
short circuit or wire breakage in 20
mA current loop of output measuring
transducer
ignition failure (signal pickup/DISN
failure)

1039 SYNCHRONIZING FAILURE

speed controller hunting eliminate cause! ---
throttle control rod loose
synchronising unit faulty
engine rough (ignition coil faulty)
voltage balance circuit faulty
engine idles too long
gas pressure oscillating

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 13 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1040 FUEL MIXTURE TEMPERATURE HIGH

defective mixture cooling pump eliminate cause! ---
mixture cooler clogged, calcified, dirty
hot water feedback temp. too high
fresh water exchanger is clogged,
calcified, dirty
defective PT100
water circulation of mixture cooling
not vented
cooling water amount of mixture too
low
wrong adjustment of fringe value

1041 POWER SIGNAL MISSING

wire breakage or short circuit of eliminate cause! ---
output signal
wire breakage or short circuit of
current transducer
output measuring transducer defect
defective current transducer
defective output controller
power setpoint too small (<10%
Pnenn)

1042 POWER SIGNAL OVERLOAD

overload isolated operation eliminate cause! ---
output controller wrong adjusted or
defective
input of wrong measuring transducer
or wrong output switch point
defective output measuring
transducer defective
current transducer defective output
controller

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 14 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1043 ENGINE OIL TEMPERATURE HIGH

oil cooler clogged, dirty eliminate cause! ---
hot water feedback temp. is too high
defective cooling water pump
cooling water heat exchanger
chocked dirty
return remperature control incorrectly
adjusted
fresh water heat exchanger chocked,
dirty
table cooler too small
ambient temp. to high (with table
cooler)
throughflow amount too low
(primary/second.)
limit value adjusted incorrectly

1047 MISFIRING FAILURE

Wrong distance of electrodes eliminate cause! ---
Wrong A/F ration
Failure in ignition system
(sparkovers, break of insulators)
Too late ignition point
Misvire detection incorrectly adjusted
or defective
Ignition defective
Ignition coil defective

1048 KNOCKING FAILURE

pre ignition (deposits in combustion eliminate cause! ---
chamber)
ignition timing point too early
monitoring set too sensitively
bad contact on the connector at the
sensor(s)
knocking sensor or knocking control
defective
Leanox controller programmed falsely
(mixture too rich)

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 15 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1050 JACKET WATER PRESSURE HIGH

slide for filling cooling water is open eliminate cause! ---
leaking plug sleeve
defective cooling water pressure
transmitter
defect. cool. water temp.
measurement and overheated motor
pressure expansion container too
small
filling pressure too high
wrong adjustment of fringe value

1051 ENGINE OIL LEVEL HIGH

defective solenoid valve "fill oil" eliminate cause! ---
defective oil level sensor or evaluator
oil level measurerer is not adjusted
(with analog measuring)
wrong adjustment of fringe value

1052 GAS PRE-ALARM

leak in gas line system eliminate cause! ---
solvent, cleaning agent in container
transmitter defective
wrong adjustment or defective
evaluator

1053 GAS ALARM

leak in gas line system eliminate cause! ---
solvent, cleaning agent in container
transmitter defective
wrong adjustment or defective
evaluator

1054 FIRE ALARM

fire eliminate cause! ---
smoke
solvent, cleaning agent in container
transmitter defect
evaluator defect

1056 FAIL SAFE LOOP TRIPPED

24V supply missing eliminate cause ! ---
safety loop monitoring tripped
emergency stop

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 16 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1059 OIL FILTER DIFFERENTIAL PRESSURE HIGH

clogging of oil filter due to dirt or eliminate cause ! ---
water in lubrication oil (check oil on
water, remedy cause.
Determine type of other dirt of the
filter by cutting open filter, possible
early bearing damage!!) filter must be
changed!

1060 PRE-LUBE PRESSURE LOW

Air pocket in oil pipe work eliminate cause! ---
Motor circuit breaker
Prelubricating pump faulty
Oil temperature too low
Oil pressure analogue sensor faulty

1061 IGNITION SYSTEM FAILURE

IC9xx Read failure from the ignition (if ---
Ignition failure caused by a possible).
malfunction in the ignition unit In case of a programme error, switch
the power supply off and then on
again.
Check whether all ignition coils are
connected.
Replace the ignition.

1064 OVERSPEED (RPS-CONTROL SYSTEM)

speed overshoot afte mains failure eliminate cause! ---
speed limit wrongly adjusted

1078 BOOST PRESSURE MEASURING SIGNAL FAILURE

24V supply to boost pressure secure interfaces ---
transducer faulty repair cables
transducer cables faulty wrong transducer
transducer range exceeded change transducer
tranduce faulty
analogue input card faulty

1080 LEANOX CONTROL ALLOWED DEVIATION EXCEEDED

measuring signal fault - actual power see fault No. 1113 ---
Measuring signal fault - mixture see fault No. 1114
Temperature see fault No. 1078
Measuring signal fault - boost see fault No. 1083
pressure
Gas mixer control defective

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 17 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1081 KNOCK SENSOR MEASURING SIGNAL FAILURE

24 V supply failure for knocking check interface ---
Sensor Check cable
Knocking sensor cable fault Change sensor
Knocking sensor defekt Move knocking sensor cable as far as
Interferance on knocking sensor possible from ignition cable
analogue input card faulty

1083 CONTROL CARBURATOR DEFECTIVE

24V supply failure for DM455 Check power supply in 24V interface TI 1000-0300
Gasmixer cable fault and at the DM455 board
Gasmixer siezed Correct wiring
24V supply failure for gasmixer Smooth running of gas mixer
position feedback Exchange fuse and board
Faulty position-feedback plate
Position feedback cable faulty

1096 MULTI MEASUREMENT DEVICE CAN COMMUNICATION FAILURE

Multi-function transducer dead Restore voltage supply at multi- ---
Incorrect/defective CAN-bus wiring function transducer
CAN-connector of the multi-function Repair CAN-bus wiring, CAN-high
transducer at the controls incorrectly and CAN-low connected correctly, no
Defective multi-function transducer short-circuit to mass, termination
resistors correct
Connector(s) plugged in correctly
Replace multi-function transducer

1101 TRANSFORMER FAILURE

Transformer overload eliminate cause! ---
Transformer out of balance
Faulty transformer cooling
Wire breakage to PLC

1105 SPEED OF TEMPERATURE CHANGE MIXTURE TEMPERATURE MAXIMUM

--- Inform the GE-JENBACHER ---
customer service department

1108 DEVIATION POWER SETPOINT TO POWER PRESENT VALUE MAXIMUM

--- Inform the GE-JENBACHER ---
customer service department

1109 GENERATOR LOSS OF EXCITATION

Voltage controller faulty change controller ---
Excitation voltage protection has Close protection switch
been tripped Check/replace the diodes
Faulty rotating diodes
defective cos-phi controller

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 18 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1110 GENERATOR FREQUENCY TOO LOW

Speed governor has been set eliminate cause ! ---
incorrectly
Speed governor is out of order
Error in speed governor circuit

1111 GENERATOR FREQUENCY TOO HIGH

Speed governor has been set eliminate cause! ---
incorrectly
Speed governor is out of order
Error in speed governor circuit

1112 NEUTRAL CURRENT MAXIMUM

generator earth fault eliminate cause! ---
limiting value on evaluation
instrument incorrectly adjusted
trigger device defective
defective current transformer in
generator
incorrect current transformer
current transformer connections
exchanged

1113 GENERATOR POWER MEASURING SIGNAL FAILURE

Mult - transducer faulty Change multi-transducer ---
Cables for multi-transducer faulty Check cables
Analogue input card faulty Change analogue input card
wrong adjustment of fringe value

1114 FUEL MIXTURE TEMPERATURE MEASURING SIGNAL FAILURE

PT100 faulty change PT100 ---
PT100 cables faulty Check cables
Analogue input card faulty

1120 SPEED MEASURING SIGNAL FAILURE

Speed pick-up wrongly adjusted Gap from 1 revolution of gear rim. ---
24V supply failure to pickup Check interface
Pickup cable fault Check cable

1121 GENERATOR WINDING (L1) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 19 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1122 GENERATOR WINDING (L2) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

1123 GENERATOR WINDING (L3) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

1124 GENERATOR BEARING (A) TEMPERATURE HIGH

bearing defective eliminate cause! ---
PT100 sensor defective
cable break to PLC
ambient temperature too high
wrong adjustment of fringe value

1125 GENERATOR BEARING (B) TEMPERATURE HIGH

bearing defective eliminate cause! ---
PT100 sensor defective
cable break to PLC
ambient temperature too high
wrong adjustment of fringe value

1126 GENERATOR VOLTAGE LOW

voltage controller fault change controller ---
Excitation voltage protection has Close protection switch
been tripped Check fuse
Blown fuse

1127 GENERATOR VOLTAGE HIGH

voltage controller fault change controller ---
Voltage controller measurement Check measurement circuit
circuit is disturbed

1129 FAILURE WITH AUXILIARIES

supply circuit breaker tripped by check wiring ---
overload check adjustment
short circuit circuit breaker

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 20 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1135 ROOM TEMPERATURE HIGH

room vent failure check the frequency controller ---
wrong adjustment or defective
thermostat
exterior temperatur too high
unfavorable placing of thermostat

1140 MODULE INTERFACE PANEL CIRCUIT BREAKER TRIPPED

Circuit breaker or engine circuit eliminate cause! ---
breaker in module control cabinet has
tripped
Power circuit breaker or engine circuit
breaker in module control cabinet is
off
Wire breakage
Loose terminal on SPC input card
Loose terminal on circuit breaker's or
engine circuit breaker's auxiliary
contacts

1143 VOLTAGE NEGATIVE SEQUENCE

fuse blown in measurement circuit check fuses ---
Generator earth fault Fault checks
Generator winding fault
Armature fault
Mains voltage assymetry

1144 CURRENT NEGATIVE SEQUENCE

current transformer circuit interuption check CT circuits ---
Mains voltage assymetry Check faults
Unbalanced load in Island operation
Earth fault

1145 JACKET WATER TEMPERATURE LOW

failure cooling water preheating eliminate cause! ---
return temperature control incorrectly
adjusted
defective cooling water temp.
transmitter
heat-up process not finished
wrong adjustment of fringe value

1148 STARTER BATTERY VOLTAGE LOW

loader defect (fuse) check battery charging ---
not enough battery acid in battery
defective battery
too strong loads
frequent starts
wire breakage to PLC

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 21 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1153 CYLINDER EXHAUST GAS TEMPERATURE MEASURING SIGNAL FAILURE

faulty thermocouple change thermocouple ---
Cable break to PLC
Analogue input card faulty

1154 GENERATOR WINDING (L1) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

1155 GENERATOR WINDING (L2) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

1156 GENERATOR WINDING (L3) TEMPERATURE HIGH

generator overload eliminate cause! ---
unbalanced load
defective generator
wrong cos-phi
PT100 sensore defective
ambient temperature too high
wrong adjustment of fringe value

1157 GENERATOR BEARING (A) TEMPERATURE HIGH

bearing defective eliminate cause ! ---
PT100 sensor defective
cable break to PLC
ambient temperature too high
wrong adjustment of fringe value

1158 GENERATOR BEARING (B) TEMPERATURE HIGH

bearing defective eliminate cause! ---
PT100 sensor defective
cable break to PLC
ambient temperature too high
wrong adjustment of fringe value

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 22 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1159 FRESH OIL TANK LEVEL LOW

no oil in fresh oil tank eliminate cause! ---
defective pump
defective floater switch

1160 WASTE OIL TANK LEVEL HIGH

tank foul eliminate cause! ---
defective pump
defective floater switch

1168 REQUEST FOR MAINTENANCE

Service counter has reached zero reset service counter after completion According to
(operating hrs) from preselected limit of service customer setting

1176 AIR INLET FILTER DIFFERENTIAL PRESSURE HIGH

clogged filter clean filter ---
cable break to PLC check cable

1177 SPARE TEMPERATURE MEASURING SIGNAL FAILURE

faulty thermocouple eliminate cause! ---
Cable break to PLC
Analogue input card faulty

1188 RELEASE FROM PLANT MANAGEMENT SYSTEM MISSING

a) Synchronization's control logic is a) Check prerequisites for logical ---
not issuing release due to unfulfilled release from synchronization
prerequisites (prerequisites relating to specific
order according to control
b) Signal error in SPC output chain in description)
synchronization/coupling
relays/wiring/coupling relays/SPC b) Eliminate cause !
input in module control

1189 RELEASE FROM SYNCHRONIZING MISSING

a) The synchronisation control logic a) Check the required conditions for ---
does not issue a release because the the logical release from the
required conditions are not fulfilled synchronisation (conditions order
specific according to control
specification)

b) Remedy cause!

1192 ACTUATOR FAILURE

Disturbance / alarm at the Actuator eliminate cause! ---
for butterfly valve (internal
equipment).
Failure voltage supply 24 VDC, wire
break

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 23 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1193 FEED BACK BOOSTER MISSING

Signal from customer Repair customer's compressor ---
Customer's compressor defective Replace digital module
Defective digital input or digital input
module

1194 FEED BACK FUEL-SKID MISSSING

Signal from customer Repair customer's gas cleaning ---
Customer's gas cleaning system system
defective Replace digital module
Defective digital input or digital input
module

1195 OPENING FAILURE OTHER GENERATOR C.B.

Interface activated eliminate cause! ---
Cable to PLC defect
Defective relay
Defective PLC card
Defective CPU

1216 BUS BAR VOLTAGE SENSOR FAILURE

measuring voltage missing eliminate cause! ---
busbars voltage-detector defective
wire breakage SPG-OK message to
PLC
PLC-input defective

1217 GENERATOR CB STATUS SIGNAL FAILURE

wire breakage check cables/connections ---
switch return messages check auxiliary contacts/answerback
circuit breaker or contactor defective of breaker or contactor
(return message/auxiliary contacts) check auxiliari contacts
relay for switch return message check/change relay
defective check PLC input (performed by GE-
PLC-input defective JENBACHER)

1218 GENERATOR CB OPENING FAILURE

ground contacts welded (with circuit change/check contactor ---
breaker/contactor combination) change/check breaker
circuit breaker defective change/check relay
relay for switch-off order is defective check breaker position signal
wrong position of retun message check/change breaker position
switch answerback relay
PLC-output defective check PLC output (performed by GE-
JENBACHER)

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 24 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

1219 GENERATOR CB CLOSING FAILURE

relay for switch-on order defective check/change relay ---
line breakage to circuit check cabels/connections
breaker/contactor check/change breaker
circuit breaker defective check PLC output
PLC output defective

1220 GENERATOR CB O-SIGNAL FAILURE

wire breakage to SPC output check cables/connections ---
monitoring check PLC input (performed by GE-
PLC input defective JENBACHER)
PLC output defective check PLC output (performed by GE-
JENBACHER)

1221 GENERATOR CB 1-SIGNAL FAILURE

wire breakage to PLC output check cables/connections ---
monitoring check PLC input (performed by GE-
PLC input defective JENBACHER)
PLC output defective check PLC output (performed by GE-
JENBACHER)

2061 CYL. 1 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2062 CYL. 2 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2063 CYL. 3 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2064 CYL. 4 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2065 CYL. 5 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2066 CYL. 6 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2067 CYL. 7 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2068 CYL. 8 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2069 CYL. 9 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 25 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

2070 CYL. 10 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2071 CYL. 11 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2072 CYL. 12 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2073 CYL. 13 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2074 CYL. 14 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2075 CYL. 15 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2076 CYL. 16 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2077 CYL. 17 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2078 CYL. 18 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2079 CYL. 19 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2080 CYL. 20 MEASURING SIGNAL FAILURE

see fault No. 1153 eliminate cause! ---

2082 PARAMETER(S) FROM DISPLAY UNIT (USER INTERFACE) MISSING

fault occured during transfer of all Send recipe in System screen ---
recipes Recall Screen No. 70 User 1
Visualisation not switched on during Cable for NET2000
first operation

2083 RPS (CONTROL SYSTEM) BATTERY FAILURE

NiCd battery for CPU2005 is flat change NiCd battery ---
(Battery LED lit) Lithium battery
Lithium battery for the user memory
is flat (Battery LED flashing)

2084 LEANOX ALGORITHM FAILURE

two identical operating point for Lox repeat Lox setup procedure ---
memory have been used

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 26 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

2086 CARBURATOR POSITION MEASURING SIGNAL FAILURE

No power supply Switch on power supply ---
Line breakage Check wiring and adjust position
Position measurement in gas mixer measurement
has been set incorrectly

2097 DEVIATION POWER SETPOINT TO POWER PRESENT VALUE MAXIMUM

Signal from client --- ---

2101 JACKET WATER TEMPERATURE MEASURING SIGNAL FAILURE

wire breakage eliminate cause! ---
short circuit
defective PT100
defective PT100 measuring
transformer
defective safety device measuring
transformer current supply
Analogue input card faulty

2102 ENGINE OIL TEMPERATURE MEASURING SIGNAL FAILURE

wire breakage eliminate cause! ---
short circuit
defective PT100
defective PT100 measuring
transformer
defective safety device measuring
transformer current supply
Analogue input card faulty

2103 ENGINE OIL PRESSURE MEASURING SIGNAL FAILURE

leak in the oil lines or the oilpan eliminate cause! ---
clogged oil cooler, oil filter or oil line
uncontrolled switching off (killing) of
engine too low speed
oil level below "min. oil level"
defective oil pressure transmitter
engine switch-off by closed current
loop (defect monitoring)
wrong adjustment of fringe value

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 27 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

2104 JACKET WATER PRESSURE MEASURING SIGNAL FAILURE

leak in cooling water system eliminate cause! ---
defective pressure transmitter of
cooling water
leaking safety valve
damaged membrane in pressure
wrong adjustment of fringe value
crack in inlet or outlet duct of cylinder
head

2106 GENERATOR WINDING TEMPERATURE L1 MEASURING SIGNAL FAILURE

wire breakage Check wiring ---
short circuit
PT100 sensore defective
Analogue input card faulty

2107 GENERATOR WINDING TEMPERATURE L2 MEASURING SIGNAL FAILURE

wire breakage Check wiring ---
short circuit
PT100 sensore defective
Analogue input card faulty

2108 GENERATOR WINDING TEMPERATURE L3 MEASURING SIGNAL FAILURE

wire breakage Check wiring ---
short circuit
PT100 sensore defective
Analogue input card faulty

2109 GENERATOR BEARING (A) TEMPERATURE MEASURING SIGNAL FAILURE

Signal from client --- ---

2110 GENERATOR BEARING (B) TEMPERATURE MEASURING SIGNAL FAILURE

Signal from client --- ---

2116 DUMP RADIATOR FAILURE

Signal from client eliminate cause! ---

2117 INTERCOOLER WATER PRESSURE LOW

leak in intercooling water system eliminate cause! ---
defective pressure transmitter of
intercooling water
leaking safety valve
damaged membrane in pressure
wrong adjustment of fringe value
crack in inlet or outlet duct of cylinder
head

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 28 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

2118 MALFUNCTION OF MIXTURE COOLING WATER PUMP

Faulty water pumps Check water pump and electric ---
Cable to PLC defect motor.
Engine emergency circuit breaker set Compare the engine emergency
incorrectly circuit breaker setting with the actual
current collection of the motor.

2120 ENGINE ROOM VENTILATION FAILURE

Cable to PLC defect eliminate cause! ---
Ventilation defect
Engine emergency circuit breaker set
incorrectly

3003 MEASURING SIGNAL FAILURE

Signal from client --- ---

3025 IGNITION TRIGGER PICKUP MISSING

Faulty pickup signals. Check the ignition sensors for ---
pollution caused by small metal
chips.
Check the distance of the sensors.
You should avoid a mechanical
contact between the triggering point
and the sensor.
Replace the faulty pickup.
Ensure that the shielding and
electrical connection are correct.

3026 IGNITION RESET PICKUP MISSING

Faulty pickup signals. Check the ignition sensors for ---
pollution caused by small metal
chips.
Check the distance of the sensors.
You should avoid a mechanical
contact between the triggering point
and the sensor.
Replace the faulty pickup.
Ensure that the shielding and
electrical connection are correct.

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 29 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3027 IGNITION CAM PICKUP MISSING

Faulty pickup signals. Check the ignition sensors for ---
pollution caused by small metal
chips.
Check the distance of the sensors.
You should avoid a mechanical
contact between the triggering point
and the sensor.
Replace the faulty pickup.
Ensure that the shielding and
electrical connection are correct.

3028 IGNITION SHUTOFF OVERSPEED

Faulty pickup signals. Check the ignition sensors for ---
pollution caused by small metal
chips.
Check the distance of the sensors.
You should avoid a mechanical
contact between the triggering point
and the sensor.
Replace the faulty pickup.
Ensure that the shielding and
electrical connection are correct.

3029 IGNITION CPU FAILURE

Faulty pickup signals. Check the ignition sensors for ---
pollution caused by small metal
chips.
Check the distance of the sensors.
You should avoid a mechanical
contact between the triggering point
and the sensor.
Replace the faulty pickup.
Ensure that the shielding and
electrical connection are correct.

3030 IGNITION PARAMETER FAILURE

Faulty value of the parameter. Error in the dia.ne programme or ---
faulty ignition.

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 30 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3031 IGNITION CAN COMMUNICATION FAILURE

CAN connection between ignition and Check whether the CAN bus is ---
dia.ne interrupted. coorectly connected to both the
Ignition not in CAN mode. ignition and the other CAN bus
participants. If the CAN bus
connection is correct, you should be
able to reset the error within 1 to 2
minutes. Please contact the GE-
JENBACHER service department if
the error cannot be reset.
Check whether the ignition has been
activated in the CAN mode. If not,
have it activated by a GE-
JENBACHER mechanic.

3032 IGNITION OUTPUT MONITORING CYLINDER 1

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3033 IGNITION OUTPUT MONITORING CYLINDER 2

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3034 IGNITION OUTPUT MONITORING CYLINDER 3

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 31 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3035 IGNITION OUTPUT MONITORING CYLINDER 4

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3036 IGNITION OUTPUT MONITORING CYLINDER 5

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3037 IGNITION OUTPUT MONITORING CYLINDER 6

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3038 IGNITION OUTPUT MONITORING CYLINDER 7

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3039 IGNITION OUTPUT MONITORING CYLINDER 8

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 32 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3040 IGNITION OUTPUT MONITORING CYLINDER 9

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3041 IGNITION OUTPUT MONITORING CYLINDER 10

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3042 IGNITION OUTPUT MONITORING CYLINDER 11

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3043 IGNITION OUTPUT MONITORING CYLINDER 12

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3044 IGNITION OUTPUT MONITORING CYLINDER 13

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 33 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3045 IGNITION OUTPUT MONITORING CYLINDER 14

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3046 IGNITION OUTPUT MONITORING CYLINDER 15

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3047 IGNITION OUTPUT MONITORING CYLINDER 16

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3048 IGNITION OUTPUT MONITORING CYLINDER 17

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3049 IGNITION OUTPUT MONITORING CYLINDER 18

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 34 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3050 IGNITION OUTPUT MONITORING CYLINDER 19

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3051 IGNITION OUTPUT MONITORING CYLINDER 20

The ignition could not generate an Check the cabling of the respective ---
ignition impulse to the ignition coil. cylinder using an ohmmeter. Move
Defective cabling between the the connector to and fro when doing
ignition and the ignition coil. so. Repair the cabling defect or
Intermittent contact at the connector replace the ignition coil.
for the ignition-coil supply.
Defective ignition coil (very rare).

3052 WRONG TYPE OF IGNITION SYSTEM

Defective ignition or wrong operating Have a GE JENBACHER mechanic ---
system. update the ignition.

3152 ENGINE ROOM TEMPERATURE MEASURING SIGNAL FAILURE

wire breakage eliminate cause! ---
short circuit
temp. transmission defective
defective PT100 measuring
transformer
wrong switch position on PLC
component
wrong adjustment of fringe value

3153 RELEASE FROM GAS PLANT MISSING

Wire breakage eliminate cause! ---
Short circuit
Defective PT100
Defective PT100 measuring
transformer
Defective fuse measuring transformer
power supply
Defective analog input card

3155 CH4 CONTENT MEASURING SIGNAL FAILURE

Defective fuse eliminate cause! ---
Wire breakage on PLC
Defective analog input card
Customer signal not present

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 35 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3158 O2 CONTENT MEASURING SIGNAL FAILURE

wire breakage eliminate cause! ---
short circuit
defective PT100
defective PT100 measuring
transducer
defective fuse at measuring
transducer
power supply

3209 IGNITION SETTING IS FORBIDDEN DURING THE ENGINE IS RUNNING

The parameters of the ignition can Stop the engine and reset the ---
only be adjusted at engine standstill. message.
Because adjustment of the If you cannot reset the message at
parameters is not currently possible, engine standstill, the ignition is
the adjustment will not be activated defective.
until the next engine standstill.

3216 ENGINE OIL TEMPERATURE HIGH

oil cooler clogged, dirty eliminate cause ! ---
hot water feedback temp. is too high
defective cooling water pump
cooling water heat exchanger
chocked dirty
return remperature control incorrectly
adjusted
fresh water heat exchanger chocked,
dirty
table cooler too small
ambient temp. to high (with table
cooler)
throughflow amount too low
(primary/second.)
limit value adjusted incorrectly

3217 MISFIRING FAILURE

Wrong distance of electrodes eliminate cause! ---
Wrong A/F ration
Failure in ignition system
(sparkovers, break of insulators)
Too late ignition point
Misvire detection incorrectly adjusted
or defective
Ignition defective
Ignition coil defective

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 36 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3218 OIL PRESSURE LOW

leak in the oil lines or the oilpan eliminate cause! ---
clogged oil cooler, oil filter or oil line
uncontrolled switching off (killing) of
engine too low speed
oil level below "min. oil level"
defective oil pressure transmitter
engine switch-off by closed current
loop (defect monitoring)
wrong adjustment of fringe value

3219 EXCITATION VOLTAGE LOW

Voltage controller faulty change controller ---
Excitation voltage protection has Close protection switch
been tripped

3220 JACKET WATER TEMPERATURE HIGH

hot water feedback temp. too high eliminate cause! ---
cooler clogged, calcified, dirty
return temperature control incorrectly
adjusted
emergency cooler clogged calcified,
dirty
fresh water missing
cool. wat. pump defect
defect. cool. water temp.
transmission
heat circulation pump defective
heat circ. slide, fresh - water slide
closed
ambient temp. too high (with table
cooler)
throughflow amount too small
(primary/secondary)
follow-up heating when shut off
water circulations not vented
motor output too high
glycool amount too high
defective short-circuit thermostat
wrong adjustment of fringe value
water circulation not vented

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 37 / 38
 Jenbacher 4.1
Documentation Checklist for alarm messages

3221 GAS PRESSURE LOW IN GAS TRAIN 1

gas valve closed eliminate cause! TI 1000-0300
wrong adjustment or defective gas
pressure controller
missing gas supply (line breakage)
pressure fluctuations by other user
defective pressure switch
no gas present (sewer gas)
wire breakage to PLC
dirty filter in supply line

3223 INTAKE AIR TEMPERATURE HIGH

Defective fuse eliminate cause! ---
Wire breakage on PLC
Defective analog input card
Customer signal not present

3224 INTAKE AIR TEMPERATURE MEASURING SIGNAL FAILURE

Exceeding the intake temperature for This warning should be regarded as ---
which full engine output was agreed. an indication, no further action is
An output reduction caused by [too required. The reasons for the output
high] an intake temperature is reduction are physical in nature.
possible. Cleaning the exhaust-gas
turbochargers will result in higher
power reserves.

Keyword: Hong Kong Nent LFG 2 Unit no.: J C623 Module no.: 446815 1
Module type : JGC 320 GS-L.L Version: C121 Engine no.: 446807 1

Issued: Doku./Lechner Checked: Dokumentation Date: 2006-02

EN 4_1___B_DianeXT_EN.doc Index: - Page - No.: 38 / 38