RailLok™ Series
BOLTABLE grooved CLIPS - Bg10
Adjustment range
Patent Pending
New features :
• Double wedge with patented
self-contact design
• “Glide washer”
• “Grooved upper component”
CLIPS C max Lateral Bolt torque (ft-lb) Estimated
adjustment Bolt grade weight
Inches Inches A325 A490 lb
Bg10/AN 1-1/16 3/8 0.56
150 ft-lb 190 ft-lb
Bg10/BN 1-11/32 3/8 0.57
Maximum resistance to lateral forces (*) 9 kips 12 kips
N: nose height, not compressed, adapted to the rail type (see table next page).
(*) The resistance is calculated on the basis that the bolt threads are excluded from the shear plan. Higher side loads can be accepted depending on
application, duty cycle and other external factors. Lower resistance is achieved in case of lower bolt grades.
Contact Gantrex for confirmation of side load in your application.
Bolts are not included unless ordered separately.
Full designation Notes on next page
• Clip Specification
Bg10/AN
or Bg10/BN • Clip Selection Table
Upper component and nose height (N)
according to rail type and foot size (F).
Components
• Components Materials
1 x Bg10/R WASHER
• Installation and Welding Instructions
1 x Bg10/27N
or 1 x Bg10/34N CLIP
www.gantrex.com GSUS-EN 2017-10 R2.0
In USA, contact GANTREX Inc. – 1-800-242-6873 – [email protected]
In Canada, contact GANTREX Canada Inc. – 1-800-884-5960 –
[email protected] RailLok™ Series
BOLTABLE grooved CLIPS - Bg10
CLIP SPECIFICATION
The RailLok™ clips are specifically engineered to facilitate correct mounting of crane rails:
• Patent pending design to ensure tight and full self-contact with the rail foot.
• Fool-proof glide washer and grooved upper component to make proper installation easier.
• Tightening by impact wrench for faster installation process.
• Lateral adjustment for better rail installation and alignment.
Once correctly installed, the clips are self-locking and self-tightening.
CLIP SELECTION TABLE FOR EACH RAIL
Mounting
F K H Weight
with pad without
Inches Inches Inches lb/yd
9/32” RailLok™ pad
A45 4.9 1.8 2.2 45 Bg10/BJ Bg10/AJ
A55 5.9 2.2 2.6 64 Bg10/BJ Bg10/AJ
A65 6.9 2.6 2.9 87 Bg10/BI Bg10/AI
A75 7.9 2.9 3.4 113 Bg10/BI Bg10/AI
ASCE40 3-1/2 1-7/8 3-1/2 40 Bg10/BJ Bg10/AJ
ASCE60 4-1/4 2-3/8 4-1/4 60 Bg10/BJ Bg10/AJ
ASCE80 (GX40) 5 2-1/2 5 80 Bg10/BJ Bg10/AJ
ASCE85 (GX42) 5-3/16 2-9/16 5-3/16 85 Bg10/BJ Bg10/AJ
105CR (MRS52) 5-3/16 2-9/16 5-3/16 105 Bg10/BI Bg10/AI
S20 3.23 1.73 3.94 40 Bg10/BJ Bg10/AJ
S30 4.25 2.37 4.25 60 Bg10/BJ Bg10/AJ
S41E1 (S41A/10) 4.92 2.64 5.43 83 Bg10/BJ Bg10/AJ
49E1 4.92 2.64 5.87 99 Bg10/BI Bg10/AI
54E1 (UIC 54) 5.51 2.76 6.26 110 Bg10/BI Bg10/AI
60E1 (UIC 60) 5.91 2.83 6.77 121 Bg10/BI Bg10/Ai
Note : All dimensions are rounded off to serve as general guidelines only. Contact Gantrex for rail sizes not shown above and for help selecting rail pads.
COMPONENTS MATERIALS
The RailLok™ Bg10 is standard with hot dip galvanized ductile cast iron components and vulcanize-bonded rubber nose.
Contact Gantrex for other options.
INSTALLATION INSTRUCTIONS
Make sure to choose the adequate bolt grade to achieve the clip side load resistance : Grade A325 for 9 kips and Grade A490 for 12 kips.
The main component is first positioned on the bolt against the rail and the special washer is then positioned on the main component with its heel into
the slot of the clip. The nut is hand tightened. Once the main component is in position, use an electrical or pneumatic wrench to torque the nut.
For most applications, use bolts complying with ISO 4014 (DIN 931) or ISO 4017 (DIN 933) and the corresponding nuts and washers.
For full instructions on the use of RailLok™ boltable clips, refer to the data sheet “Installation Instructions”.
Do not apply protective coating on the contact surface between components and support unless accepted by Gantrex. Do not use solvents as they may
seriously damage the rubber nose.
We reserve the right to discontinue or change specifications or design at any time without prior notice and without incurring
any obligation whatsoever.
www.gantrex.com GSUS-EN 2017-10 R2.0
In USA, contact GANTREX Inc. – 1-800-242-6873 – [email protected]
In Canada, contact GANTREX Canada Inc. – 1-800-884-5960 –
[email protected]
