JHTL ARCHITECTURAL DESIGN FIRM

jhartzerlagatgmail.com

PROPOSED 2-STOREY RESIDENTIAL BUILDING

Specifications

Prepared By:
JULES HARTZER T. LAGAT
BS-ARCH 3A

Submitted to:
AR. ROEL MOZART ACEBES
BUILDING TECHNOLOGY 4 INSTRUCTOR

1|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

GENERAL BUILDING SPECIFICATIONS

[FOR HLURB PURPOSES ONLY]

DIVISION 1: GENERAL REQUIREMENTS

01100 SUMMARY

Project Name: PROPOSED 2-STOREY RESIDENTIAL BUILDING

Project Owner: MR. RONALD MOGAN
Represented by: JULES HARTZER LAGAT
Location: NEW CARMEN, TACURONG CITY, SULTAN KUDARAT, PHILIPPINES

01300 ADMINISTRATIVE REQUIREMENTS

ARCHITECTURAL
Perspective
Site Development
Vicinity Map

Ground Floor Plan

Second Floor Plan

Schedule Of Windows
Front Side Elevation
Left Side Elevation
Right Side Elevation
Rear Side Elevation

Cross Section
Longitudinal Section

GF Reflected Ceiling Plan

2nd Floor Schedule of Floor Finishes

GF Schedule Of Floor Finishes

2nd Floor Schedule of Floor Finishes
Schedule Of Door

Overhead Kitchen Cabinet

Base Kitchen Cabinet
Section A, Section B, Section C, And Section D

Masters’ Bedroom Walk-In-Closet and Toilet

Section A, Section B, Section C And Section D
Second A, B, C, And D

2|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

Second Floor Common Toilet

Section A, B, C, And D
Ground Floor Toilet

Section A, B, C And D
Section A, B, C, And D
Masters’ Closet Plan Section
Bedroom 1, 2, And 3 Closet
Plan, Section, Elevation Balcony Railing Detail
STRUCTURAL
Ground Floor Foundation Plan
Schedule of Footing and Column
Lintel Beam Section Detail
Porch Stairs Section Detail
Footing Tie Beam Section
Concrete Pavement Section
C1-F1 Section
C2- F2, F3 Section Detail
Wf-1 Section
C1-F1, C2-F2, C3-F3, C4-F4

Second Floor Framing Plan

Schedule of Beams
Typical Concrete Beam Section
2B-1 Concrete Beam
2B-2 Concrete Beam
2B-3 Concrete Beam

Roof Beam plan

Schedule of Roof Beams
2B-1 Concrete Roof Beam
Slab Section
Typical Two-Way Slab

Upper Roof Full Section

Half Truss-A
Hip Truss
Hip Truss-B
Stair Section Detail
Stair Plan
Stair Spot Detail-01
Stair Spot Detail-02
Stair Spot Detail-03

3|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

01600 PRODUCT REQUIREMENTS

FAÇADE FINISHES
FRONT ELEVATION -
 UNION GALVASTEEL DURATILE
 0.50 mm (Brown)

 PERMACOAT SEMI-GLOSS LATEX

 Tulle White B-706
 FIXED PANEL CORNER WINDOW USING 1" FLOAT BRONZE GLASS AND ANALOK FRAMES.
 PLANT BOX

 PERMACOAT SEMI-GLOSS LATEX

 Antique White BSC-27
 100mm THK. REINFORCED CONCRETE WALL PERMACOAT SEMI-GLOSS LATEX
 Antique White BSC-27

 PERMACOAT SEMI-GLOSS LATEX

 Basic Beige BSG-9
 PERMACOAT SEMI-GLOSS LATEX
 Mud Pie B-7581

LEFT SIDE ELEVATION-

 RIDGE ROLL
 UNION GALVASTEEL DURATILE
 0.50 mm (Brown)
 EDGE GUTTER
 0.50 mm (Brown)
 CONCRETE CANOPY SLAB PVC WOODEN PLANKS CEILING BELOW CONCRETE CANOPY SLAB
 CONCRETE MOULDING
 ANALOK SLIDING DOOR FRAMES WITH
 FLOAT BRONZE GLASS
 FIXED PANEL WINDOW USING
 SMOKED FLOAT BRONZE GLASS AND ANALOK
 FRAMES. STEEL RAILING
 CONCRETE MOULDING
 CONCRETE CANOPY SLAB CONCRETE MOULDING
 OUTDOOR WALL LAMP ANALOK WINDOW FRAMES WITH
 FLOAT BRONZE GLASS
 GROOVED WOODEN SOLID DOOR
 WITH SMALL STRI DRIVEWAY RAMP

RIGHT SIDE ELEVATION-

 RIDGE ROLL
 UNION GALVASTEEL DURATILE
 0.50 mm (Brown)
 EDGE GUTTER

4|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

 0.50 mm (Brown) CONCRETE MOULDING

 ANALOK WINDOW FRAMES WITH FLOAT BRONZE GLASS

 GROOVED WALL: 13mm H. & 13mm D.
 @ 300 mm SPACING FROM FINISH FLOOR LINE OF LANAI PERMACOAT SEMI-GLOSS LATEX
 Mud Pie B-7581 CONCRETE CANOPY SLAB
 PVC WOODEN PLANKS CEILING BELOW CONCRETE CANOPY SLAB
 RED MAHOGANY SLIDING DOORS
 WITH ¼ " FLOAT BRONZE GLASS
 OUTDOOR WALL LAMP
 FIXED PANELS WITH AWNING WINDOWS
 USING ¼ " FLOAT BRONZE GLASS AND ANALOK FRAMES

REAR ELEVATION-
 PERMACOAT SEMI-GLOSS LATEX
 Tulle White B-706
 PVC WOODEN PLANKS CEILING BELOW CONCRETE CANOPY SLAB
 OUTDOOR WALL LAMP
 RECTANGULAR TUBE (2"x 4") RAILINGS
 SQUARE TUBE (1"x 2") RAILINGS SQUARE TUBE (1"x 1") RAILINGS
 PERMACOAT SEMI-GLOSS LATEX
 Tulle White B-706
 PERMACOAT SEMI-GLOSS LATEX
 Antique White BSC-27
 ANALOK AWNING WINDOW FRAMES WITH FLOAT BRONZE GLASS
 GROOVED WOODEN SOLID DOOR
 WITH SMALL STRIP
 PERMACOAT SEMI-GLOSS LATEX
 Mud Pie B-7581

DIVISION 2: SITE CONSTRUCTION

02050 BASIC SITE MATERIALS AND METHODS
GENERAL

1. THESE NOTES CONTAIN GENERAL INFORMATION AND ARE NOT COMPLETE FOR
CONSTRUCTION PURPOSES. CONTRACTOR SHALL VERIFY INFORMATION GIVEN HERE WITH
THE SPECIFICATIONS AND OTHER DOCUMENTS AND BRING ANY CONFLICTS TO THE
ATTENTION OF THE ENGINEER BEFORE BEGINNING AFFECTED WORK. THE ENGINEER WILL
RESOLVE ANY SUCH CONFLICTS.
2. BEFORE FABRICATION AND/OR CONSTRUCTION ALL DIMENSIONS SHALL BE VERIFIED AND
COORDINATED WITH ARCHITECTURAL, ELECTRICAL, PLUMBING AND MECHANICAL
DRAWINGS.
3. THE CONTRACT STRUCTURAL DRAWINGS AND SPECIFICATIONS REPRESENT THE FINISHED
STRUCTURE. THEY DO NOT INDICATE THE METHODS OF CONSTRUCTION, UNLESS SO
STATED. THE CONTRACTOR SHALL PROVIDE ALL NECESSARY MEASURES TO PROTECT THE

5|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

STRUCTURES, ADJACENT PROPERTY, WORKMEN AND OTHER PERSONS DURING ALL PHASES
OF CONSTRUCTION
4. THE CONTRACTOR SHALL PROVIDE TEMPORARY ERECTION BRACING AND SHORING FOR
ALL STRUCTURAL MEMBERS AS REQUIRED FOR STRUCTURE STABILITY DURING ALL PHASES
OF CONSTRUCTION.
5. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS OTHERWISE SPECIFIED.

02450 FOUNDATION AND LOAD-BEARING ELEMENTS

FOUNDATION
FOUNDATION DESIGN WAS BASED ON ASSUMED ALLOWABLE SOIL BEARING CAPACITY
OF 5730 PSF (275 KPa). THE CONTRACTOR SHALL VERIFY SOIL CONDITION AT SITE & SHALL
NOTIFY STRUCTURAL ENGINEER IF ACTUAL SOIL PROPERTY APPEARS WEAKER TO THAT
ASSUMED. FOUNDATION SHALL REST ON NATURAL SOIL UNLESS OTHER WISE NOTED BY
THE ENGINEER. NO PART OF FOUNDATION SHALL REST ON FILL. THE CONTRACTOR SHALL
NOTIFY THE ENGINEER AFTER FOOTING EXCAVATION HAVE BEEN COMPLETED AND PRIOR
TO CONCRETING TO CONFIRM THE DESIGN SOIL BEARING CAPACITY.

DIVISION 3: CONCRETE
BASIC CONCRETE MATERIALS & METHODS

03050 CONCRETE & REINFORCEMENT

1. ALL MATERIALS AND WORKMANSHIP SHALL CONFORM WITH THE LATEST BUILDING CODE
OF AMERICAN CONCRETE INSTITUTE (ACI-318).
2. ALL CONCRETE SHALL DEVELOP A MIN. COMPRESSIVE STRENGTH AT THE END OF TWENTY
EIGHT (28) DAYS W/ CORRESPONDING MAXIMUM SIZE AGGREGATE & SLUMPS AS
FOLLOWS.

LOCATION 28 DAYS STRENGTH MAX. SIZE AGGREGATE MAX. SLUMP

FOUNDATION 3000 PSI (20.7 MPa) (CRASHED ROCK) 4 IN. (100 MM)
COLUMNS 3000 PSI (20.7 MPa) 3/4 IN. (19 MM) 4 IN. (100 MM)
SUSPENDED BEAMS & 3/4 IN. (19 MM)
SLABS 3000 PSI (20.7 MPa) 3/4 IN. (19 MM) 4 IN. (100 MM)
SLAB ON GRADE
ALL OTHERS 3000 PSI (20.7 MPa) 3/4 IN. (19 MM) 4 IN. (100 MM)
3000 PSI (20.7 MPa) 3/4 IN. (19 MM) 4 IN. (100 MM)

3. ALL REINFORCING BARS SHALL CONFORM TO ASTM SPECS GRADE 33 (227 MPa) FOR 12Ø &
SMALLER AND GRADE 40 (275 MPa) FOR 16Ø TO 25Ø BARS.
4. IN GENERAL THE LATEST EDITION OF ACI-315, MANUAL OF STANDARD PRACTICE DETAILING
REINFORCED CONCRETE STRUCTURES SHALL BE ADHERED TO UNLESS OTHERWISE SHOWN
OR NOTED.
5. MAINTAIN MINIMUM CONCRETE COVER FOR REINFORCING STEEL AS FOLLOWS.

SUSPENDED SLABS 3/4 IN. (19 MM)

SLAB ON GRADE 1 1/2 IN. (38 MM)
WALLS ABOVE GRADE 1 IN. (25 MM)

6|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

BEAM STIRRUPS AND COLUMN TIES 1 1/2 IN. (38 MM)

WHERE CONCRETE IS EXPOSED TO 2 IN. (50 MM)
EARTH BUT POURED AGAINST FORMS 3 IN. (75 MM)
WHERE CONCRETE IS DEPOSITED
DIRECTLY AGAINST EARTH

6. SPLICES SHALL BE SECURELY WIRED TOGETHER & SHALL LAP OR EXTEND IN ACCORDANCE
W/ TABLE 1 (TABLE OF LAP SPLICE & ANCHORAGE LENGTH) UNLESS OTHERWISE SHOWN
ON DRAWINGS, SPLICES SHALL BE STAGGERED WHENEVER POSSIBLE.
7. ALL ANCHOR BOLTS, DOWELS, AND OTHER INSERTS, SHALL BE PROPERLY POSITIONED &
SECURED IN PLACE PRIOR TO PLACING OF CONCRETE.
8. CONTRACTOR SHALL NOTE AND PROVIDE ALL MISCELLANEOUS CURBS, SILLS, STOOLS,
EQUIPMENT'S AND MECHANICAL BASES THAT ARE REQUIRED BY THE ARCHITECTURAL,
ELECTRICAL, AND MECHANICAL DRAWINGS.
9. ALL CONCRETE SHALL BE KEPT MOIST FOR A MINIMUM OF SEVEN CONSECUTIVE DAYS
IMMEDIATELY AFTER POURING BY THE USE OF WET BURLAP FOG SPRAYING, CURING
COMPOUNDS OR OTHER APPROVED METHODS.
10. STRIPPING OF FORMS AND SHORES:

FOUNDATION 24 HRS.

SUSPENDED SLAB EXCEPT WHEN 8 DAYS

ADDITIONAL LOADS ARE IMPOSED
WALLS 18 HRS.
BEAMS 14 DAYS

11. DEVELOPMENT LENGTH (Ld) OF REINFORCING STEEL BARS SHALL BE AS FOLLOWS:

SIZE OF BARS (mm) DEVELOPMENT LENGTH (mm)
10 375
12 440
16 590
20 730
25 920
28 1030
32 1170
IF THE DEPTH OF CONCRETE CAST IN ONE LIFT BENEATH THE BARS EXCEEDS 300 mm, INCREASE THE
ABOVE LENGTHS BY 1.40.

03100 CONCRETE FORMS AND ACCESSORIES

LINTEL BEAM
1. STIRRUPS SHOULD HAVE AT LEAST 10MM ⌀ WIDE STIRRUPS AT 200MM O.C.
2. TOP BARS SHOULD HAVE AT LEAST 12MM ⌀ WIDE
3. BOT BARS SHOULD HAVE AT LEAST 12MM ⌀ WIDE

7|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

FOOTING TIE BEAM - TIE BEAM IS A TYPE OF BEAM WHICH IS USED TO TIES THE
FOOTING AND TO AVOID THE SLENDER COLUMN EFFECT IN THE STRUCTURE. IT
INCREASES THE STIFFNESS OF THE OVERALL STRUCTURE.

1. 10MM⌀ STIRRUPS SP. AT 2

03200 CONCRETE REINFORCEMENT

DIVISION 4: MASONRY

04100 BASIC MASONRY MATERIALS AND METHODS

MASONRY AND CONCRETE BLOCKS

1. ALL NON-LOAD BEARING TYPE CONCRETE BLOCKS SHALL HAVE A UNIT WEIGHT NOT TO
EXCEED 80 PCF. FOR LOAD BEARING TYPE, TYPE CONCRETE BLOCKS, A MINIMUM
COMPRESSIVE STRENGTH f'm = 3.50 MPa (500psi) SHALL BE DEVELOPED.
2. PROVIDE 1-Ø16 VERTICAL BARS AT CORNERS, INTERSECTIONS, END OF WALLS AND EACH
SIDE OF OPENINGS.
3. LINTEL BEAMS SHALL BEAR AT LEAST 8 INCHES (200 MM) ON EACH SIDE OF MASONRY WALL
OPENING.
4. WALL REINFORCEMENTS SHALL BE AS FOLLOWS.

WALL THICKNESS 6 IN. (150 VERTICAL REINFORCEMENT HORIZONTAL REINFORCEMENT

MM) Ø12 @ 600 MM Ø10 @ 600 MM
4 IN. (100 MM) Ø12 @ 600 MM Ø10 @ 600 MM

5. REINFORCING BARS SHALL BE LAPPED A MINIMUM OF 30 BAR DIAMETERS WHERE SPLICE

DOWELS FROM FOOTING OR SLABS SHALL EXTEND INTO THE BLOCK WALL A MINIMUM OF
30 BAR DIAMETERS. REBARS TO BE PROPERLY TIED W/ G.I. WIRE.

DIVISION 5: METALS
DIVISION 6: WOOD AND PLASTICS
DIVISION 7: THERMAL & MOISTURE PROTECTION
DIVISION 8: DOORS & WINDOWS
DIVISION 9: FINISHES
DIVISION 10: SPECIALTIES
DIVISION 11: EQUIPMENT
DIVISION 12: FURNISHINGS

8|Page
JHTL ARCHITECTURAL DESIGN FIRM
jhartzerlagatgmail.com

DIVISION 13: SPECIAL CONSTRUCTION

DIVISION 14: CONVEYING SYSTEMS
DIVISION 15: MECHANICAL
DIVISION 16: ELECTRICAL

9|Page