Valves & Regulators

Valves & Regulators

c Pressure
- Electronic Pressure Switches
- Mechanical Pressure Switches
- Pressure Transducer
c Valves & Regulators
c Temperature
c Level
c Flow
c Air Suspension Valves
 Table of Contents

Valves & Regulators

Directional Control Valve Products Supplemental Guide 3

Valves
Series 9000, 9020 - Shear-Seal® Directional Control Valve 7
Series 9040, 9080 - Low Pressure OEM Valves 9
Series 6140, 6180 - High Pressure OEM Valves 11
Series 6900, 6940 - High Pressure OEM Manipulator Valves 13
Series 140, 200, 920, 5620 - Heavy Duty Valves 15
Series 3760 - Subplate Mounted Heavy Duty Valve 17
Models A14 and H14 - Series II Valve 19
Model 371MT7 - Explosion Proof Position Indicator 21
Series 4140 - High Pressure Valve 23
518, 526 Series - MicrotorqueTM Valve 25
Series 422 Solenoid Valve - Shear-Seal® Directional Control 27

Regulators
Series 20313 - 1/2” Heavy Duty Hydraulic Regulator 29
Series 20415 - 3/4” Hydraulic Regulator 31
Series 20495 - 3/4” Heavy Duty Hydraulic Regulator 33
Series 20517 - 1-½” Hydraulic Regulator 35
Series 20597 - 1-½” Heavy Duty Hydraulic Regulator 37

Relief Valve
Series 8010 - Pressure Relief Valve 39
Installation and Operating Instructions for Hydraulic Relief Valve 41
Supplemental Guide
Interflow and Non-Interflow in Barksdale Valves
Valves
Directional Control Valve Products

Interflow in a Barksdale Shear-Seal® valve is a small amount of fluid flow from the Pressure A and B ports to the return port through
the clearance between the rotor and the body. This interflow occurs whenever the valve is shifted from one position to another or
when the valve is being used for throttling. This is due to the Shear-Seal® in the valve being only partially covered by the rotor.
Interflow is not leakage and does not occur when the valve is fully engaged.

The interflow in a Shear-Seal® valve is beneficial in that it reduces the hydraulic shock or “water hammer” that can occur when a
valve is closed rapidly. The small amount of interflow between ports acts as a cushion as the fluid flow is stopped in the system.

Non-interflow valves are constructed with Shear-Seal®s using a much smaller flow passage than a comparably sized interflow valve.
By doing this, the orifice in the pressure seal and rotor are completely covered during transition thus preventing interflow. Non-
interflow valves may be required when precise control of a cylinder is needed and the small settling associated with interflow valves
can not be tolerated. Non-interflow valves have a much lower flow rate than interflow valves with the same port size. Mandatory
higher force is required to actuate them.

Barksdale Shear-Seal® Valves are available with many standard options as well as special order features. Many of the options
available are listed below. Consult Factory for additional details and availability for a particular valve model. Don’t see what you need
here? Call us - we’re only a phone call away.

Seal Material Std. P/N Suffix Modification Std. P/N Suffix

Butyl -Z10 2-Position 45° CW detent -Z30
Neoprene -Z12 2-Position 45° CCW detent -Z31
Viton® -Z13 2-Position 90° detent -Z32
EPR -Z15 No valve detent -Z33
Silicone -Z16 No valve handle -Z34
FSR -Z17 Valve with actuator mounting
-Z35
Thiokol -Z18 Hardware only (no actuator)

Teflon (PTFE) -Z19

Disogrin -Z21

Maintenance
1. Disassemble and inspect. Replace or repair damaged or worn parts and “O” rings; clean all parts including solenoid and
plunger. Grease valve parts before assembly. The solenoid should be cleaned at least every 1,000,000 cycles or every six months.
The valve should be checked every 2,000,000 or once a year.
2. All Barksdale manual selector valves for water service are equipped with a grease fitting in the housing. On untreated water, valve
should be lubricated through this fitting. Frequency of lubrication depends entirely on duty cycle of valve. An increase in handle
load will indicate exactly what lubrication schedule should be followed. Use water resistant lubricant such as Socony-Vacuum
“Sovarex 2W”, Shell “Alvania” or equivalent. Preceding operation may be disregarded if valve is used on water treated with
soluble oil.
3. At the first sign of excessive internal leakage the valve should be disassembled and the source of leakage repaired. Allowing valve
to continue in operation may cause damage to other components, as the escaping fluid is generally in the form of a jet stream.

WARNING: Reverse assembly of any valve parts may result in high case pressure and possible injury. Assembly drawings, sales
drawings and parts lists MUST be consulted.

1
Supplemental Guide Directional Control Valve Products
Pressure Drop Curves

(Theoretical)

150 3/16
7/32 9/32
5/16 3/8
1/4
7/16
140 17/32
1/2

130 9/16

5/8

120
PRESSURE DROP (PSI)

110
23/32

100

90
3/4
80
70

60

50 7/8

40

30 1

20 1-1/8

1-1/4
10

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
RATE OF FLOW (G.P.M.) - HYD. OIL OR WATER

Pressure Drop
Barksdale’s Shear-Seal® Valves have a much lower pressure drop than other valve technologies. This is possibly due to smooth
internal passages and transitions within the valves which keep turbulent fluid flow to a minimum. This translates to less heat build-up
and higher pressures available to perform the required work.

Determine Pressure Drop for Barksdale Shear-Seal Valves

1. Determine the Rate of Flow in G.P.M. or L.P.M. for fluid being controlled.
2. Determine minimum flow passage for valve from vale data sheet or sales drawing.
3. Locate the Pressure Drop Curve from the chart above for the appropriate minimum flow passage
(indicated by the small circles at each curve).
4. Read the Pressure Drop from the vertical axis at the point where the flow rate (horizontal axis) intersects
the appropriate pressure drop curve.

Note: The Pressure Drop is about the same in all flow directions.

2
Supplemental Guide
Velocity Curves
Valves
Directional Control Valve Products

(Theoretical)

9/32 5/16 7/16

70 7/32 3/8 1/2 17/32 9/16 5/8 23/32 3/4

3/16 1/4
65

60
VELOCITY (FT. PER SEC.)

55 7/8

50

45
1
40
35

30 1-1/8

25 1-1/4

20

15

10
5

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
RATE OF FLOW (G.P.M.)

Fluid Velocity
Barksdale’s Shear-Seal® Valves control fluid at a much higher velocity than other types of valve technologies. This means that a
smaller valve can be used to do the same types of job, saving you space and component costs. The recommended velocity for
Barksdale valves is about 30 ft/sec (9.1 m.sec) for continuous operation. However, the valve can easily handle higher velocities up to
60 ft/sec (19.3 m/sec) for intermittent duty.

Determining Fluid Velocity in a Shear-Seal Valve for a known Rate of Flow

1. Determine the Rate of Flow in G.P.M. or L.P.M. for fluid being controlled.
2. Determine minimum flow passage for valve from valve data sheet or sales drawing.
3. Locate the Velocity curve from the chart above for the appropriate minimum flow passage (indicated
by the small circles at each curve).
4. Read the Velocity from the vertical axis at the point where the flow rate (horizontal axis) intersects the
appropriate Velocity curve.

3
Supplemental Guide Directional Control Valve Products
Trouble-Shooting Pointers

Barksdale Manual Directional Control Valves

SUSPECTED TROUBLE SOLUTION SUSPECTED TROUBLE SOLUTION

High force required to shift valve Internal Leakage around Shear-Seal
Possible Cause
1 Restriction or blockage in “return” port 1 Remove restriction 1 Worn Shear-Seal O-ring 1 Replace O-ring
causing back pressure in excess of
maximum allowable for valve style SUSPECTED TROUBLE SOLUTION
Internal Leakage
2 Valve installed in system incorrectly 2 Install valve correctly Across Face of Shear-Seal®
allowing pressure to be applied to 1 Scratch or other damage to face of 1 Replace Shear-Seal®. Field dressing
return port Shear-Seal® can be performed on the face of
Shear-Seal® by lapping with 600 grit
3 Bent detent disk rubbing valve hous- 3 Repair or replace detent disk paper. Paper should be held secure-
ing ly on a surface plate for best results.

4 Dirt or debris under trust washer caus- 4 Disassemble and clean valve 2 Scratch or other damage to rotor 2 Lap rotor with 600 grit paper as
ing tipping of rotor described above. Replace rotor if
leakage continues
5 Worn or missing pin rotor pin on shaft 5 Disassemble and replace shaft pin
which allows rotor to rub on housing 3 Incorrect position of rotor in relation to 3 Replace detent disk or shaft pins
Shear-Seals®. This can be caused by
6 Worn or scored thrust washers caus- 6 Replace thrust washers and bearings. worn rotor shaft pins or worn detent
ing bearings to bind If balls run on top of rotor inspect this disk
area for damage as well.
4 Wear on surface of Shear-Seal® after 4 Replace Shear-Seal®s
7 Pressure in excess of valve rating 7 Reduce working pressure of valve in millions of cycles. This can reduce
system with regulator, relief valve or other spring tension on Shear-Seal® due to
means. material loss on seal face.

8 Lip worn off of Shear-Seal® 8 Replace Shear-Seals® 5 Shear-Seal® spring fails due to break- 5 Replace springs
age or taking permanent set.
9 Galling between Shear-Seal® and rotor 9 This is typically an affect of rotor tip-
ping. Replace Shear-Seal®. If possible SUSPECTED TROUBLE SOLUTION
grind and lap rotor and use shim on top External Leakage Between
of rotor to make up difference that is Body and Housing
ground off. Otherwise replace rotor.
1 Improperly installed body O-ring 1 Replace body O-ring and install
SUSPECTED TROUBLE SOLUTION completely in O-ring groove
Symptom: Leakage around shaft
2 Excessive back pressure in housing 2 Check pressure at return port with
1 Worn shaft O-ring 1 Replace shaft O-ring caused by restriction or blockage in pressure gauge and insure it is
return port. Back pressure can cause below maximum rating for valve.
2 Enlarged shaft hole in housing caused 2 Replace housing. Inspect shaft for body bolts to stretch and allow leak- Replace body O-ring
by side load on shaft. Typically only wear and replace if necessary. age at body O-ring
found when valve is actuated by some Correct side loading condition.
mechanical means which is mis- 3 Body bolts not tightened to specifica- 3 Replace body O-ring and tighten
aligned tion on assembly drawing. bolts as per assembly drawing

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
4 See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0050-D • 03/08 • ©2008 • Printed in the U.S.A.
 Shear-Seal® Directional Control Valve
Features
Valves Series 9000, 9020
Original Shear-Seal® technology
Interflow/non interflow
Easy panel mounting
Tolerates contaminates
Spring return option

Applications
Pilot valve for pneumatic valve actuators
Gas manifold controls
Manual control of 2-position cylinder

Shown with option “D” red ball type handle

General Specifications*
Working Pressure: Pneumatic or hydraulic from 150 Media Temperature Range: -40° to +250°F (-40° to +121°C)
psi to 350 psi (10.3 to 24.1 bar); see
Wetted Material:
table
Body: Anodized aluminum
Cv, Minimum Orifice: See table
Standard O-Rings: Buna N
Back Pressure: Must not exceed 250 psi (17.2
bar) at return port for satisfactory
Pressure Seals: Brass
operation
Proof Pressure: 1-1/2 times working pressure except Rotor: Hard anodized aluminum
at return port (without damage to
Handle Rotation: 90°; 45° each side of center
valve)
Burst Pressure: 2-1/2 times working pressure except Detent: 3-position detent (except -MC,
at return port (300 psi, 20.7 bar) -MR options)
* See product configurator for additional options.

CLOSED CENTER CLOSED CENTER (Float Center) OPEN CENTER

T T T T T T

Port Min. Cv Air and Oil Manipulator Approx.

Size Flow Factor Rated Rated Shipping
NPT Passage Pressure Pressure Weight
Dia. psi (bar) psi (bar) lbs. (kg)
1/4” 3/16” 0.52 150 (10.3) 150 (10.3) 2 (0.9)
9000 Series
Non Interflow 3/8” 3/16” 0.52 150 (10.3) 150 (10.3) 2 (0.9)
1/4” 3/8” 2.3 350 (24.1) 250 (17.2) 2 (0.9)
9020 Series
3/8” 3/8” 2.3 350 (24.1) 250 (17.2) 2 (0.9)
Interflow
1/2” 3/8” 2.3 350 (24.1) 250 (17.2) 2 (0.9)

1
Shear-Seal® Directional Control Valve Series 9000, 9020
Technical Drawings
REGULAR

#10-24NC-2 THD. PANEL MOUNTING

.375 MIN. FULL THD. SURFACE .250 MAX.
A FOR PANEL MTG. G1 DIA. PANEL THICKNESS
(TYP) 4 PLACES “-D” option “-C” option
A PORT*
SPRING CENTER/REVERSE RED BALL MOUNTING BRACKET
B TYPE HANDLE and 4 SCREWS
PANEL MOUNTING
SURFACE
G2 DIA.
H
PORT* E PORT*
C
1.250
(31.8 ) F1
2.125
PORT* (54.0)
H 2.375
2.781 C E 5.437 (60.3)
(70.6) (138.1)
D1 F2
1.0 (25.4) 1.0 (25.4)
.562 (14.3)
“-E” option
BLACK KNOB 2.781 1.0 (25.4) .281 DIA.
(not available with spring return) (70.6) 3 PLACES
D2 3.125
(79.4) 2.0
(50.8)
.625

2.375

Dimensions in inches (mm)

PORT Black Regular Spring Black Regular Spring Black Regular Spring
SIZE Knob Center/ Knob Center/ Knob Center/
Rever Rever Rever
NPT
A B C D D-1 D-2 E F F-1 F-2 G G-1 G-2 H J
1/4 & 3/8 1.000 2.625 4.125 3.656 4.781 5.188 1.688 2.062 2.000 2.406 0.437 0.437 1.906 0.531 0.656
(25.4) (66.7) (104.8) (92.9) (121.4) (133.8) (42.9) (52.4) (50.8) (61.1) (11.1) (11.1) (48.4) (13.5) (16.7)
1/2 1.000 3.125 4.125 3.718 4.843 5.250 1.750 2.125 2.062 2.468 0.437 0.437 1.906 0.625 0.937
(25.4 (79.4) (104.8) (94.4) (123.0) (133.4) (44.5) (54.0) (52.4) (62.7) (11.1) (11.1) (48.4) (15.9) (23.8)

Product Configurator Example: 902 2 -M

Series Optional O-ring Material

900 Non interflow -Zxx See supplemental guide
902 Interflow Options
-B 2-position 90° rotation (no center position)
Port Size -C Mounting bracket w/ 4 screws
1 1/4” pressure port -D Red ball type handle
2 3/8” pressure port
-CD Mounting bracket & red ball type handle
3 1/2” pressure port (interflow only)
-E Black knob (not available for spring return)

Operation
-M Manual operation Flow Pattern
-MC Manual (spring return to center) Blank if closed center selector
-MR Manual (spring return to reverse) -A Closed center manipulator

-G Open center manipulator

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0040-H • 12/08 • ©2008 • Printed in the U.S.A. 2
 Low Pressure OEM Valves
Features
Valves Series 9040, 9080
Patent # 3,014,499
Original Shear-Seal® technology
Low pressure drop
Tolerates contaminates
Spring return option
Flexible design

Applications
Paper mill controls
Air pilot valves
Halon fill systems
Heating oil control
Compressed gas manifold control

General Specifications*
Working Pressure: Gasses or hydraulic fluids up to 500 Media Temperature -40° to +250°F (-40° to +121°C)
psi (34 bar) Range:
Flow Capacity, Cv: See table Wetted Material:
Rotor: Hard anodized aluminum
Back Pressure: Must not exceed 250 psi (17.2 bar) at
return port for satisfactory operation
Pressure Seals: Brass
Pressure Drop: 14 psi (0.96 bar) at 20 ft/sec
See Supplemental Guide for more Shaft: Stainless steel
detailed information
Proof Pressure: 1-1/2 times working pressure except Body, Housing: Anodized aluminum
at return port
Bearings: Teflon/stainless steel
Burst Pressure: 2-1/2 times working pressure except
at return port (500 psi [34 bar]) Standard O-rings: Buna N, others available
* See product configurator for additional options.

Flow Capacity (Approx.)

Service: Oil Approx.
20 ft/sec 40 ft/sec Min. Flow Shipping
Main Valve gpm gpm 60 ft/sec Passage Cv Weight
Port Size (l/min) (l/min) gpm (l/min) Dia. Factor lbs (kgs)
1/2" & 3/4" 14 (53) 28 (106) Use 17/32" 4.80 3 (1.4)
1" 25 (95) 51(190) Heavy 23/32" 9.20 10-1/2 (4.8)
1-1/2" 62 (235) 124 (471) Duty Valve 1-1/8" 24.0 20 (9.1)

1
Low Pressure OEM Valves Series 9040, 9080
Technical Drawings
9040 SERIES

9080 SERIES

9040 Series Regular (side) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/2" & 3/4" 3.5 (88.9) 5.44 (138) 7.37 (187.3) 7.94 (201.6) 2.56 (65.0) 3/8 - 16 NC 3.03 (77.0) 0.56 (14.2) 2.56 (65.0) 0.88 (22.4) 3.38 (85.9) 3.94 (100)
1" 4.5 (114) 8.44 (214) 8.16 (207) 9.03 (229.4) 3.31 (84.1) 1/2 - 13 NC 3.59 (91.2) 0.75 (19.1) 3.375 (85.7) 1.06 (26.9) 3.94 (100) 4.81 (122.2)
1-1/2" 6.38 (162) 10.35 (263) 9.66 (245) 10.53 (267.5) 4.75 (121) 3/4 - 10 NC 4.656 (118.3) 0.88 (22.4) 3.375 (85.7) 1.37 (34.9) 5.03 (128) 5.906 (150)

9080 Series Straight (bottom) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/2" & 3/4" 4.19 (106) 5.44 (138) 7.34 (186) 7.9 (200.8) 2.56 (65.0) 3/8 - 16 NC 3.88 (98.6) 0.56 (14.2) 2.56 (65.0) 2.50 (65.5) 4.22 (107) 4.78 (121)
Dimensions in inches (mm)

Product Configurator Example: 904 5 R 0 A C 3

Series
904 Regular (side) porting

908 Straight (bottom) porting

Options
Port Size Pressure Range
See Supplemental Guide
-
3 1/2” NPT ports 0 500 psi max. Air or hydraulic fluid for complete list
4 3/4” NPT ports
1” NPT ports
5
(Series 904 only)
Service
1-1/2” NPT ports Options
7 A Air (pneumatic) or hydraulic fluid
(Series 904 only)
-A SAE porting

Style -MC Spring centering

Flow Pattern
Regular (side) porting,
R C Closed center
(Series 904)
Position
Straight (bottom) porting, O Open center (tandem center)
S 3 Three position
(Series 908)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0055-B • 12/07 • ©2007 • Printed in the U.S.A. 2
 High Pressure OEM Valves
Features
Valves Series 6140, 6180
Patent# 3,014,499
Original Shear-Seal® technology
Low pressure drop
Tolerates contaminates
Spring return option
Flexible design for OEM requirements

Applications
Hydraulic presses
Military equipment
Paper mill controls
Hydraulic pilot valves
Railroad maintenance equipment
Halon fill systems

General Specifications*
Working Pressure: Hydraulic fluid up to 3000 psi (206 Media Temperature -40° to +250°F (-40° to +121°C)
bar) Range:
Flow Capacity, Cv: See table Wetted Material:
Rotor: Hard anodized aluminum
Back Pressure: Must not exceed 250 psi (17.2
Bar) at return port for satisfactory
Pressure Seals: Brass
operation
Pressure Drop: 14 psi (0.96 bar) at 20 ft/sec Shaft: Stainless steel
See Supplemental Guide for more
detailed information Body Housing: Anodized aluminum
Proof Pressure: 1-1/2 times working pressure except
at return port Bearings: Carbon steel

Burst Pressure: 2-1/2 times working pressure Standard O-rings: Buna N, others available
except at return port (see flow chart)
* See product configurator for additional options. Back-up Rings: Teflon®

Flow Capacity (Approx.)

Service: Oil Approx.
20 ft/sec 40 ft/sec 60 ft/sec Min. Flow Shipping
Main Valve gpm gpm gpm Passage Cv Weight Return Port
Port Size (l/min) (l/min) (l/min) Dia. Factor lbs (kgs) Burst Rating
1/4" & 3/8" 5 (19) 10 (38) Use 5/16" 1.56 1 1/2 (0.7)
3,000 psi (207 bar)
1/2" & 3/4" 14 (53) 28 (106) Heavy 17/32" 4.80 3 (1.4)
** 1" 25 (95) 51(190) Duty 23/32" 9.20 10 1/2 (4.6) 2,000 psi (138 bar)
** 1-1/2" 62 (235) 124 (471) Valve 1-1/8" 24.0 20 (9.1) 1,500 psi (103 bar)
** 6140 Series Only

1
High Pressure OEM Valves Series 6140, 6180
Technical Drawings

6140 Series

6180 Series

6140 Series In-Line (side) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/4" & 3/8" 2.63 (66.8) 5.44 (138) 6.38 (161.9) 6.718 (170.6) 1.81(46.0) 5/16 - 18 NC 2.31(58.7) 0.44 (11.2) 1.91(48.5) 0.56 (14.2 2.66 (67.6) 3.03 (77.0)
1/2" & 3/4" 3.5 (88.9) 5.44 (138) 7.37 (187) 7.93 (201) 2.56 (65.0) 3/8 - 16 NC 3.03 (77.0) 0.56 (14.2) 2.56 (65.0) 0.88 (22.4) 3.38 (85.9) 3.94 (100)
1" 4.5 (114) 8.44 (214) 8.16 (207) 9.03 (229.3) 3.31 (84.1) 1/2 - 13 NC 3.59 (91.2) 0.75 (19.1) 3.38 (86) 1.06 (26.9) 3.94 (100) 4.81 (122)
1-1/2" 6.38 (162) 10.35 (263) 9.66 (245) 10.53 (268) 4.75 (121) 3/4 - 10 NC 4.6 (118) 0.88 (22.4) 3.38 (86) 1.34 (34.0) 5.03 (128) 5.91 (150)

6180 Series Straight (bottom) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/4" & 3/8" 2.63 (66.8) 5.44 (138) 6.13 (156) 6.50 (165) 1.81(46.0) 5/16 - 18 NC 2.66 (67.6) 0.44 (11.2) 1.91(48.5) 1.50 (38.1) 3.00 (76.2) 3.38 (85.9)
1/2" & 3/4" 4.19 (106) 5.44 (138) 7.34 (186) 7.91 (201) 2.56 (65.0) 3/8 - 16 NC 3.88 (98.6) 0.56 (14.2) 2.56 (65.0) 2.50 (65.5) 4.22 (107) 4.78 (121)
Dimensions in inches (mm)

Product Configurator Example: 614 2 R 3 H C 3

Series
614 Regular (side) porting
Options
618 Straight (bottom) porting
Pressure See Supplemental
Guide for complete list
3 3,000 psi
Port Size
1 1/4” NPT ports Working Media Options
2 3/8” NPT ports H Hydraulic oil -A SAE Porting
3 1/2” NPT ports -MC Spring centering *
4 3/4” NPT ports Flow Pattern Non-interflow (port size 1/4”
-NF
5 1” NPT ports (614 only) and 3/8” NPT only)
C Closed center
7 1-1/2” NPT ports (614 only) * For 1” ported pressure rating 2,500 psi
O Open center (tandem center)
Not available on 1-1/2” ported valves.

Style Position
R Regular (side) porting (series 614)
3 3-position
S Straight (bottom) porting (series 618)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0054-B • 11/08 • ©2008 • Printed in the U.S.A. 2
 High Pressure OEM Manipulator Valves
Features
Valves Series 6900, 6940
Patent# 3,014,499
Original Shear-Seal® technology
Low pressure drop
Tolerates contaminates
Spring return option
Special flow pattern for OEM designs

Applications
Hydraulic presses
Military equipment
Paper mill controls
Pipe forming
Railroad maintenance equipment

General Specifications*
Working Pressure: Hydraulic fluid up to 3000 psi (206 Media Temperature -40° to +250°F (-40° to +121°C)
bar) Range:
Flow Capacity, Cv: See table Wetted Material:
Rotor: Hard anodized aluminum
Back Pressure: Must not exceed 250 psi (17.2
Bar) at return port for satisfactory
Pressure Seals: Brass
operation
Pressure Drop: 14 psi (0.96 bar) at 20 ft/sec Shaft: Stainless steel
See Supplemental Guide for more
detailed information Body Housing: Anodized aluminum
Proof Pressure: 1-1/2 times working pressure except
at return port Bearings: Carbon steel

Burst Pressure: 2-1/2 times working pressure Standard O-rings: Buna N, others available
except at return port (3000 psi [206
bar]) Back-up Rings: Teflon®

* See product configurator for additional options.

Flow Capacity (Approx.)

Service: Oil Approx.
20 ft/sec 40 ft/sec 60 ft/sec Min. Flow Shipping
Main Valve gpm gpm gpm Passage Cv Weight
Port Size (l/min) (l/min) (l/min) Dia. Factor lbs (kgs)
Use
1/4" & 3/8" 5 (19) 10 (38) Heavy 5/16" 1.56 1 1/2 (0.7)
Duty
1/2" & 3/4" 14 (53) 28 (106) Valve 17/32" 4.80 3 (1.4)

1
High Pressure OEM Manipulator Valves Series 6900, 6940
Technical Drawings

6900 Series

6940 Series

6900 Series In-Line (side) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/4" & 3/8" 2.63 (66.8) 5.44 (138) 6.38 (161.9) 6.718 (170.6) 1.81(46.0) 5/16 - 18 NC 2.31(58.7) 0.44 (11.2) 1.91(48.5) 0.56 (14.2 2.66 (67.6) 3.03 (77.0)
1/2" & 3/4" 3.5 (88.9) 5.44 (138) 7.37 (187) 7.93 (201) 2.56 (65.0) 3/8 - 16 NC 3.03 (77.0) 0.56 (14.2) 2.56 (65.0) 0.88 (22.4) 3.38 (85.9) 3.94 (100)

6940 Series Straight (bottom) Porting

Port Size A B C C1 D E F G G1 H J J1
NPT Dia. Dia.
1/4" & 3/8" 2.63 (66.8) 5.44 (138) 6.13 (156) 6.50 (165) 1.81(46.0) 5/16 - 18 NC 2.66 (67.6) 0.44 (11.2) 1.91(48.5) 1.50 (38.1) 3.00 (76.2) 3.38 (85.9)
1/2" & 3/4" 4.19 (106) 5.44 (138) 7.34 (186) 7.91 (201) 2.56 (65.0) 3/8 - 16 NC 3.88 (98.6) 0.56 (14.2) 2.56 (65.0) 2.50 (65.5) 4.22 (107) 4.78 (121)
Dimensions in inches (mm)

Product Configurator Example: 690 2 R 3 H C 3

Series
Regular (side) porting, manipulator
690
flow pattern Options
Straight (bottom) porting, Pressure See Supplemental
694
manipulator flow pattern Guide for complete list
3 3,000 psi

Port Size Working Media

1 1/4” NPT ports Options
H Hydraulic oil
2 3/8” NPT ports -A SAE Porting
3 1/2” NPT ports -MC Spring centering
Flow Pattern
4 3/4” NPT ports Non-interflow (port size 1/4”
C Closed center manipulator (float center) -NF
and 3/8” NPT only)
O Open center (tandem center)
Style
R Regular (side) porting (series 690)
Position
S Straight (bottom) porting (series 694)
3 3-position

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0057-A • 11/08 • ©2008 • Printed in the U.S.A. 2
Heavy Duty Valves
Features
Original Shear-Seal®
technology
Valves Series 140, 200, 920, 5620
Patent# 2.696.219

High velocity flow

Tolerates contaminates
Low handle load at high pressures
Spring return option
Low pressure drop

Applications
Land-based and offshore drilling equipment
Steel mills
Nitrogen charging panels
Refineries and chemical processing plants
Power generation facilities

General Specifications*
Working Pressure: Air (pneumatic) up to 4,000 psi (276 bar) Media Temperature -40° to +250°F (-40° to +121°C)
hydraulic oil or lubricated water up to Range:
6,000 psi (413 bar) Rotor: 400 series stainless steel
Flow Capacity, Cv: See table Pressure Seals: Stainless steel
Back Pressure: Must not exceed 250 psi (17.2 bar) at Shaft: Stainless steel
return port for satisfactory operation
Body: Bronze
Pressure Drop: 14 psi (0.96 bar) at 20 ft/sec
See Supplemental Guide for more Housing: Ductile iron
detailed information Standard O-ring: Buna N, others available
Proof Pressure: 1-1/2 times working pressure except at
Back-up Rings: Teflon®
return port
Burst Pressure: 2-1/2 times working pressure except at
return port (3,000 psi [206 bar])
* See product configurator for additional options.

Flow Capacity (Approx.)

Service: Oil and Lubricated Water
Main Valve 20 ft/sec 40 ft/sec 60 ft/sec Min. Flow Cv Approx. Shipping
Port Size gpm (l/min) gpm (l/min) gpm (l/min) Passage Dia. Factor Weight lbs (kgs)
1/4” 3 (11) 6 (23) 9 (34) 1/4” 0.95 4.5 (2)
140/920 3/8” & 1/2” 9 (34) 19 (72) 28 (106) 7/16” 3.20 8.5 (3.9)
Series
Valve 3/4” & 1” 25 (95) 50 (189) 75 (284) 23/32” 9.20 21.5 (9.8)
1-1/2” 57 (217) 114 (433) 171 (650) 1-3/32” 21.00 48.5 (22)
1/4” 3 (11) 6 (23) 9 (34) 1/4” 0.95 4.5 (2)
200/562
Series 1/2” 5 (19) 10 (38) 15 (57) 5/16” 1.60 8.5 (3.9)
Valve
1” 9 (34) 19 (72) 28 (106) 7/16” 3.20 21.5 (9.8)

1
Heavy Duty Valves Series 140, 200, 920, 5620
Technical Drawings
E (4 TAPPED HOLES) PANEL J-1 H
PANEL MOUNTING STUDS J H MOUNTING
CYL. 2 F PRESSURE STUDS
PANEL OPTIONAL PRESSURE
MOUNTING F
STUDS
OPTIONAL

CYL. 1

A D

G
DIA.

B CL PORTS RETURN G-1

DIA.
CL PORTS RETURN
D C
A C-1

PANEL MOUNTING
DIMENSIONS SPRING CENTERED

DIMENSIONS in inches (mm)

Port
G G-1
Size A B C C-1 D E F H J J-1
Dia. Dia.
NPT
1/4” 2.6 (66.0) 5 (127.0) 4.7 (119.4) 4.87 (124) 1.8 (48.3) 3/8 - 16 NC 2.6 (66.0) 0.7 (17.8) 1.9 (48.3) 0.6 (15.2) 2.9 (73.7) 3.1 (79.3)
3/8” & 1/2” 3.3 (83.8) 7.0 (177.8) 6.8 (173) 6.8 (173) 2.4 (61.0) 3/8 - 16 NC 3.5 (88.9) 1.1 (27.9) 2.6 (66.0) 0.7 (17.8) 4.0 (101) 3.9 (99.1)
3/4” & 1” 4.6 (116.8) 10.0 (254.0) 8.7 (221.0) 9.9 (251.5) 3.6 (91.4) 1/2 - 13 NC 4.8 (121.9) 1.3 (33.0) 3.6 (91.4) 1.0 (25.4) 5.2 (132.1) 6.4 (162.6)
1-1/2” * 6.8 (172.7) 12.0 (304.8) 10.5 (266.7) 11.8 (299.7) 5.3 (134.6) 3/4 - 10 NC 6.2 (157.5) 1.3 (33.0) 3.6 (91.4) 1.5 (38.1) 6.5 (165.1) 7.8 (198.1)
* 1 1/2” available in 140 and 920 Series only

Product Configurator Example: 20 3 P 6 W C 3

Series
14 Basic 140 series valve (3,000 psi)
20 Basic 200 series valve (6,000 psi)

92
Basic 920 series valve (3,000 psi Options
manipulator)
See Supplemental
Basic 5620 series valve (6,000 psi
562
manipulator)
Working Media - Guide for complete
list
A Air (pneumatic)
Port Size Lubricated water
W
or hydraulic oil
1 1/4” NPT ports
2 3/8” NPT ports (Series 140 & 920 only)
3 1/2” NPT ports Flow Pattern
4 3/4” NPT ports (Series 140 & 920 only) C Closed center (Series 140, 200)
5 1” NPT ports Open center (tandem center)
O
(Series 140, 200)
7 1-1/2” NPT ports (Series 140 & 920 only)
Manipulator (float center)
Q
(Series 920, 5620)
Port Location
R Regular (side) porting
Position
P Panel mount with side porting
3 Three position

Pressure Range
Options
3,000 psi lubricated water or hydraulic,
3 -MC Spring centering * * For 1” ported valve pressure rating 1,500 psi
2,000 psi air (14 & 92 Series)
Not available on 1-1/2” ported valves
-MS SAE Porting
6,000 psi lubricated water or hydraulic,
6
4,000 psi air (20 & 562 Series)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0035-F • 11/08 • ©2008 • Printed in the U.S.A. 2
 Subplate Mounted Heavy Duty Valve
Features
Valves Series 3760
Patent # 2.696.219
Original Shear-Seal® technology
Convenient sub-plate manifold mounting
Low pressure drop
High velocity flow
Tolerates contaminates
Low handle load at high pressures

Applications
Steel mills
Shipboard hydraulic control systems
Refineries and chemical processing plants
Power generation facilities

General Specifications*
Working Pressure: Hydraulic oil or lubricated Wetted Material:
water up to 4,500 psi (310 bar) Rotor: 400 series stainless steel
Flow Capacity, Cv: See table
Pressure Seals: Stainless steel
Back Pressure: Must not exceed 250 psi (17.2
Bar) at return port for satisfactory Shaft: Stainless steel
operation
Body: Bronze
Pressure Drop: 14 psi (0.96 bar) at 20 ft/sec
* See Supplemental Guide for more
Housing: Ductile iron
detailed information
Proof Pressure: 1-1/2 times working pressure except Standard O-rings: Buna N, others available
at return port
Burst Pressure: 2-1/2 times working pressure except Back-up Rings: Teflon®
at return port (3,000 psi [206 bar])
Subplates: (Optional) Carbon steel
Media Temperature -40° to +250°F (-40° to +121°C)
Range:
* See product configurator for additional options.

Flow Capacity (Approx.) Approx.

Service: Oil and Lubricated Water Min. Flow Shipping
Main Valve 20 ft/sec 40 ft/sec 60 ft/sec Passage Cv Weight
Port Size gpm (l/min) gpm (l/min) gpm (l/min) Dia. Factor lbs (kgs)
3760 1/2" 9 (34) 19 (72) 28 (106) 7/16" 3.20 8.5 (4.5)
Series 1" 25 (95) 50 (189) 75 (284) 23/32" 9.20 24 (10.9)
Valve 1-1/2" 57 (217) 114 (433) 171 (650) 1-3/32" 21.00 53 (24)

1
 Subplate Mounted Heavy Duty Valve Series 3760
Technical Drawings
A-1
A
G
H
J J
L L N
Q K K 4 PLACES
0 DIA.
B1 T-1 DIA.
DIA. 4 PLACES T DIA.
4 PLACES
H B
J P DIA. S1
R M 4 PLACES S
K
K
F
G M CYL. 1
J CYL. 1
SPRING
CENTERED
D
M M PRESSURE

Optional CYL. 1
Sub Plate E
C DIA.
RETURN (4 PLACES)

CYL. 2

Valve Dimensions - inches (mm)

Size A A-1 B B-1 C D E F S S-1 T T-1
1/2" 7.00 (178) 9.00 (229) 5.81 (148) 6.06 (154) 0.47 (12) 3.44 (87) 5.44 (138) 3.56 (90) 3.94 (100) 4.06 (103) 1.06 (27) 2.63 (67)
1" 10.0 (254) 14.0 (356) 7.63 (194) 8.81 (224) 0.75 (19) 4.75 (121) 6.88 (175) 4.81(122) 5.13 (130) 6.19 (157) 1.25 (32) 3.56 (90)
1-1/2" 12.00 (305) 14.0 (356) 8.75 (222) 10.0 (254) 1.25 (32) 6.81 (173) 9.38 (238) 5.94 (151) 6.25 (159) 7.5 (191) 1.25 (32) 3.56 (90)

SubPlate Dimensions - inches (mm) Options:

Sub Plate
Size Port Type G H J K L M N O P Q R WT.
p/n
NPT 34013 6.0 (152) 3.0 (76) 2.19 (56) 0.78 (20) 1.19 (30) 1.41 (36) 3/8 N.C. 0.41 (10) 1/2 NPT 1.25 (32) 0.44 (11)
1/2" 11 3/4
Socket Weld 34011 6.0 (152) 3.0 (76) 2.19 (56) 0.78 (20) 1.19 (30) 1.41 (36) 3/8 N.C. 0.41 (10) .855 C'Bore 1.25 (32) 0.44 (11)
NPT 34015 8.0 (203) 4.0 (102) 2.88 (73) 1.25 (32) 1.81 (46) 1.97 (50) 1/2 N.C 0.53 (13) 1" NPT 2.0 (51) 0.72 (19)
1" 32 1/2
Socket Weld 34012 8.0 (203) 4.0 (102) 2.88 (73) 1.25 (32) 1.81 (46) 1.97 (50) 1/2 N.C 0.53 (13) 1.330 C'bore 2.0 (51) 0.72 (19)
NPT 34016 10.0 (254) 5.0 (127) 4.0 (102) 1.94 (49) 2.69 (68) 2.69 (68) 5/8 N.C. 0.53 (13) 1 1/2 NPT 2.0 (51) 1.22 (31)
1-1/2" 49
Socket Weld 34014 10.0 (254) 5.0 (127) 4.0 (102) 1.94 (49) 2.69 (68) 2.69 (68) 5/8 N.C. 0.53 (13) 1.915 C'bore 2.0 (51) 1.22 (31)
NPT 34018 10.0 (254) 5.0 (127) 4.0 (102) 1.94 (49) 2.69 (68) 2.69 (68) 5/8 N.C. 0.53 (13) 2" NPT 2.0 (51) 1.22 (31)
2" 49
Socket Weld 34017 10.0 (254) 5.0 (127) 4.0 (102) 1.94 (49) 2.69 (68) 2.69 (68) 5/8 N.C. 0.53 (13) 2.406 C'bore 2.0 (51) 1.22 (31)

Product Configurator Example: 376 5 M 3 W C 3

Series
Options
Basic 376 series
376 See Supplemental Guide
valve
for complete list

Port Size
Working Media
3 1/2” NPT ports Lubricated water or
W
5 1” NPT ports hydraulic
Options
7 1-1/2” NPT ports
-MC Spring centering *
Flow Pattern -H 4,500 psi rated
Style Closed center
C * For 1” ported valve pressure rating 1,500 psi
M Manifold porting Not available on 1-1/2” ported valves
O Open center (tandem center)
Q Closed center manipulator
Pressure Range
3,000 psi lubricated water Position
3
or hydraulic oil
3 3-position

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0037-D • 11/08 • ©2008 • Printed in the U.S.A. 2
 Series II Valve
Valves Patent# US D521.598 S
Models A14 and H14
Patent# US D521.599 S
Features
Original Shear-Seal® technology
Integrated actuator
2- and 3-position
Superior shifting performance
High velocity flow
Compact design
Corrosion resistant materials

Applications
Land-based & offshore oil drilling controls
BOP control units
Steel mills
Shipboard hydraulic control systems
Industrial hydraulic power units
Refineries and chemical processing plants
General Specifications*
- Main Valve - Pilot Actuator
Working Pressure: Hydraulic up to 3,000 or 6,000 psi Working Pressure:
(206 bar or 413 bar) Air: 80 psi (5.2 bar) minimum
Air up to 4,000 psi (276 bar) 250 psi (17.2 bar) maximum
Flow Capacity, Cv: Hydraulic (2-position only): 500 psi (34 bar) minimum
See table
1,500 psi (103 bar) maximum
Back Pressure: Must not exceed 250 psi (17.2 bar) at
Porting: 1/4” NPT
return port for satisfactory operation
Proof Pressure: Media Temperature Range: -40° to +250°F (-40° to +121°C)
1-1/2 times working pressure except
at return port Speed of Operation: Shift time for 90° must be 1/2
Burst Pressure: 2-1/2 times working pressure except second minimum to avoid damage
at return port (3,000 psi [206 bar]) Body, Housing, End Plate: Al-Ni Bronze
Pressure Drop 20 ft/s –14 psi; 6.1 m/s – 1 bar Cylinder: Amalga tubing (air)
(all Valves): 40 ft/s – 58 psi; 12.2 m/s – 4.0 bar Stainless steel (hydraulic)
60 ft/s – 130 psi; 18.3 m/s – 9.0 bar Shaft: Stainless steel
Media Temperature -40° to +250°F (-40° to +121°C) Hardware: Stainless steel
Range:
Handle: Zinc plated alloy steel
Wetted Materials: 400 Series Stainless Steel
Standard O-Rings: Buna N Rotor, Seals: 400 series stainless steel
Back-up Rings: Teflon® 2-POSITION FLOW PATTERN SELECTOR
(VIEWED FROM SHAFT END)
3-POSITION FLOW PATTERN SELECTOR
(VIEWED FROM SHAFT END)
CYL1 CYL1 CYL1 CYL1 CYL1
Handle Detent: All valves have 3-position detents for
PRESS RET PRESS RET PRESS RET PRESS RET PRESS RET
manual shift to Center position
CYL2 CYL2 CYL2 CYL2 CYL2

Panel Mounting: Standard for 1/4”- 1/2” valves HANDLE ORENTATION (AS SHOWN CW)
(ACTUATOR PORT 'B' PRESSURIZED)
HANDLE ORENTATION (AS SHOWN CCW)
(ACTUATOR PORT 'A' PRESSURIZED)
HANDLE ORENTATION (AS SHOWN CW) HANDLE CENTERED HANDLE ORENTATION (AS SHOWN CCW)
(ACTUATOR PORT 'B' & ‘C’ PRESSURIZED) (ACTUATOR PORT 'A' & ‘C’ PRESSURIZED) (ACTUATOR PORT 'A' PRESSURIZED)
Consult Factory for 3/4” & 1” valves MAIN VALVE
1 2
(PORTS ‘A’ VENTED) ( PORT ‘B’ VENTED) (PORTS ‘B’ & ‘C’ VENTED)
MAIN VALVE
1 2
* See product configurator for additional options. A R P B
AB C
1 2 R P
C1 C2 C R

P R
PILOT VALVE 4-WAY
Flow Capacity (Approx.) P R
PILOT VALVE 4-WAY
P
PILOT VALVE 3-WAY

Service: Oil and Lubricated Water

Approx. CLOSED CENTER MANIPULATOR FLOW PATTERN
Main Valve 20 ft/sec 40 ft/sec 60 ft/sec Min. Flow Cv Shipping CYL1
(VIEWED FROM SHAFT END)
CYL1 CYL1
Port Size NPT gpm (l/min) gpm (l/min) gpm (l/min) Passage Dia. Factor Weight PRESS RET PRESS RET
PRESS RET
14, 92 1/4" 3 (11) 6 (23) 9 (34) 1/4" 0.95 30 CYL2 CYL2
Series 3/8" & 1/2" 9 (34) 19 (72) 28 (106) 7/16" 3.20 35 HANDLE ORENTATION (AS SHOWN CW) HANDLE CENTERED HANDLE ORENTATION (AS SHOWN CW)
(ACTUATOR PORT 'B' PRESSURIZED) (MANUALLY OVERRIDE ONLY) (ACTUATOR PORT 'A' PRESSURIZED)
Valves 3/4" & 1" 25 (95) 50 (189) 75 (284) 23/32" 9.20 50
MAIN VALVE
20, 562 1/4" 3 (11) 6 (23) 9 (34) 1/4" 0.95 30 1 2 1 2 1 2

Series 1/2" 5 (19) 10 (38) 15 (57) 5/16" 1.60 35 A R P R P B

Valves 1" 9 (34) 19 (72) 28 (106) 7/16" 3.20 50 1 2

P R
PILOT VALVE 4-WAY

1
 Series II Valve Models A14 and H14
Technical Drawings
A 2-Position Valve 3-Position Valve
PANEL MOUNT P P
N
E (4 PLACES)
D 3.40
PANEL CUTOUT

D
L L
A C
D

B C PANEL
C MOUNT
N
H H B (3)
D R
J Q T
C M
B
B S U 2X 1/2-13 UNC-2B 1.00
9 PANEL MOUNTING HOLES
A
A

K K
G
F

K
G 9.509

F
1/4”, 3/8”, 1/2” 3/4”, 1"

Porting A B C D E F G H J K L M N P Q R S T U

2.75 10.38 2.0 1.0 5.0 5.72 4.25 .50 3.34 3.25 1.94 9.43 4.88 7.44 2.44 3.75 8.44 10.468
1/4” NPT 3/8-16UNC
(60.3) (254.0) (50.8) (25.4) (127.0) (146.1) (108) (12.7) (85) (82.6) (49.2) (231.7) (124.0) (189.0) (62) (95.3) (214.4) (265.9)

3/8” & 1/2” 3.406 10.937 2.625 1.312 5.0 6.25 4.75 .688 3.531 3.25 1.94 9.531 5.50 7.85 2.56 3.88 8.688 10.25
3/8-16UNC
NPT (86.5) (277.8) (66.7) (33.3) (127.0) (158.8) (120.65) (17.46) (89.7) (82.6) (49.2) (242.1) (139.7) (199.3) (65.1) (98.4) (220.7) (260.4)

3/4” & 1” 4.781 14.375 3.625 1.812 9.0 8.75 6.562 1.0 4.25 3.50 3.0 12.0 7.562 10.125
1/2-13UNC NA NA NA NA
NPT (121.4) (365.1) (92) (46) (228.6) (222.3) (166.6) (25.4) (108) (88.9) (76.2) (482.0) (192.0) (257.0)

Product Configurator Example: A 20 3 R 6 W C 3

Actuator Media
A Air cylinder
Optional O-ring Material
H Hydraulic cylinder
-Zxx See supplemental guide

Series
14 3,000 psi (206 bar), 4-way selector or diverter Pressure Range
Options
20 6,000 psi (412 bar), 4-way selector or diverter 3,000 psi lubricated water
3 or hydraulic oil, 2,000 psi air -B Position Indicator
92 3,000 psi (206 bar), 4-way closed center
manipulator (14, 92 & 376 Series)
-C 3 x 2 converter
562 6,000 psi (412 bar), 4-way closed center 6,000 psi lubricated water
-H 4,500 psi working pressure
manipulator 6 or hydraulic oil, 4,000 psi air
(20 & 562 series) -M 5,000 psi working pressure
376 3,000 psi (206 bar), 4-way sub-plate mount
-D Diverter flow pattern

Working Media -MS SAE Porting

Port Size
W Lubricated water or hydraulic oil -Zxx Optional O-ring material1
1 1/4” NPT
A Air or other gasses
2 3/8” NPT (14 and 92 series only)
3 1/2” NPT
4 3/4” NPT (14 and 92 series only) Flow Pattern Position
5 1” NPT C Closed center 2 2-position actuator, 90º rotation
O Open center (tandem center) 3 3-position actuator
Port Location Closed center manipulator
Standard on 92 and 562 series 1
R Regular side porting Q See Supplemental Guide for the appropriate
Optional on 376 Series in closed center only “Z number”
M Manifold porting (376 series only) Not available on 14 and 20 Series

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0022-I • 02/09 • ©2009 • Printed in the U.S.A. 2
 Explosion Proof Position Indicator
Reliable valve position feedback for Series II Valve
Valve Model 371MT7

Features
Fits all Series II valves
2 position and 3 position
30 VDC max, 500 mA (PLC compatible)
Designed for Division I and I.S. use
UL & ATEX approved
NEMA 4X, IP67

Applications
Valve status output
BOP closing unit ‘OPEN-CLOSE’ signal
Hydraulic power units

UL &
ATEX
appr
oved

General Specifications*
Housing Material: Stainless steel Approvals: Division 1, Class 1, Groups A, B, C & D
Enclosure: NEMA 4X, IP67 Ex d ia IIc T6
Intrinsically safe to 24 VDC, 50 mA,
Electrical Rating: 30 VDC max, 500 mA (carry current) 10 W

Electrical Connection: ½” NPT rotating female conduit Valve Position 2-Way

connection with 3 ft (36 in) cable Feedback: 3-Way
Operating Temperature: -40 to +185°F (-40 to 85°C)
Electrical Cable: UL listing, 4 conductors, 22
Installation Instructions: - Connect electrical wires
AWG TPE flame resistant jacket.
- Lightly lubricate the position
Resistance to oils, fuels, and solvents
indicator O-rings (2)
- Fully insert switch into stop screw
Maximum Contact 100 milliohms
- Rotate position indicator for
Resistance:
optimum cable exit
- Secure set screws (2)
Dielectric: 100 megaohms minimum
(@ 250 VDC) Weight: 2 lbs.
Switch Type: SPST
* See Product Configurator for additional options.

Wiring Code

CYLINDER 2/ORANGE

CENTER/RED

CYLINDER 1/BROWN

COMMON/BLACK

CASE GROUND - DRAIN

1
Explosion Proof Position Indicator Model 371MT7
Reliable valve position feedback for Series II Valve
Technical Drawings
57.2
1.45 1.22 2.95
36.8 31 75

2X .50
371MT75
12.7
1.26
32
FLATS

1.54
O-RING 39
.24 BUNA-N 2X .87
6 FLATS
22
1 9/16-12 UN-2A
3.6
91.4 1.417
JAM NUT 36
CONDUIT GROUND SCREW
NAMEPLATE 8-32 UNC-2A
UL/ATEX NAMEPLATE NOT SHOWN

4X 10-24 UNC-2A X .31

SOCKETHEAD SETSCREW, CUP POINT 1.65
UL/ATEX NAMEPLATE 42
2.09
53

CABLE 5 8
1/2 NPT THREAD
2.09
53 1.65
1.06 42
26.9 1.417
FLATS 36
1.375
34.9
1.65 1.65
42 .83 2.83 42
1.13
28.6 21.0 72.0
1.45±.010
36.8±0.25

1.54
371MT73
1.73 1.42 39.0
44.0 36.0
CABLE 5 8

.24 2.81 1.38

3/4-16 UNF 2A 6.0 71.4 34.9
.50
JAM NUT 12.7
GROUND 3.60
6X #10-24 UNC X .31 LG (2) O-RINGS 91.4
SET SCREW 2.28 (BUNA-N) SCREW 1.26 1.65
58.0 8-32 UNC-2A 32.0 42.0
1/2 NPT MALE THREADS
.91
23.0

2.28 CABLE 5 8
58.0 1.85
47.0
.91 1.38 STOP SCREW TO REMAIN IN VALVE
1.06 23.0 34.9 DO NOT REMOVE
26.9 FITTING - JAM NUT

Product Configurator
When ordering together Example: Series II Valve part number -B
with Series II Valves Base Model Optional Cable Length
-B Position indicator for ¼” and ½” Series II valves Additional cable length
XXX
-B Position indicator for 1” and 1½” Series II valve (in inches)

When ordering separately Example: 371MT7 3

as replacement or spare part
Base Model Optional Cable Length
371MT7 Position indicator Additional cable length
-Wxxx
(in inches)
Size
3 Fits ¼” and ½” Series II valves
5 Fits 1” and 1-1/2” Series II valves

When ordering to retrofit Example: 371MT73-KIT

existing valves without -B option Size Optional Cable Length

371MT73-KIT Fits ¼” and ½” Series II valves Additional cable length
-Wxxx
371MT75-KIT Fits 1” Series II valves (in inches)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
2
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0053-C • 02/11 • ©2011 • Printed in the U.S.A.
High Pressure Valve
Features
Valves Series 4140

Original Shear-Seal® technology

Stainless steel construction
Low pressure drop
High velocity flow
Pressures to 15,000 psi
Low handle load

Applications
Offshore drilling equipment
Refineries and chemical processing plants
Gas compression systems
Marine umbilical reels

General Specifications*
Working Pressure: Standard to 10,000 psi (690 bar) Media Temperature -40° to +250°F (-40° to +121°C)
Optional to 15,000 psi (1,034 bar) (on 1/4” Range:
model only) Rotor: 400 series stainless steel
Flow Capacity, Cv: See table Pressure Seals: Stainless steel
Back Pressure: Must not exceed 250 psi (17.2 bar) at return Shaft: Stainless steel
port for satisfactory operation
Body, Housing: 300 series stainless steel
Pressure Drop: 14 psi (0.96 bar) at 20 ft/s
Standard O-ring: Buna N
Proof Pressure: 1-1/2 times working pressure except at
return port Back-up Rings: Teflon®
Burst Pressure: 2-1/2 times working pressure except at
return port (3,000 psi [206 bar]) maximum
* See product configurator for additional options and Supplemental Guide for more detailed information.

Flow Capacity (Approx.)

Service: Oil and Lubricated Water

Main Valve 20 ft/sec 40 ft/sec 60 ft/sec Min. Flow Cv Approx. Shipping

Port Size gpm (l/min) gpm (l/min) gpm (l/min) Passage Dia. Factor Weight lbs (kgs)

1/4” 4 (15) 8 (30) 12 (45) 9/32” 0.95 13.5 (6.2)

1/2” 4 (15) 8 (30) 12 (45) 9/32” 0.95 13.5 (6.2)

1” 9 (34) 19 (72) 28 (106) 7/16” 3.20 29.5 (13.5)

1
High Pressure Valve Series 4140
Technical Drawings

2.50
DIA. E DIA. CYL. 2
(4 HOLES)
1.06
DIA.

.31
.25
MOUNTIN D
C J PLATE G

PRESSURE

CL PORTS D CYL. 1
H G
K
RETURN (TYP.)
A
DIA.

Port A B C D E F G H J K
Size Dia. Dia.
1/4” 3.50 (89) 7.00 (178) 7.69 (195) 3.25 (83) 0.28 (7) 4.22 (107) 4.00 (102) 0.63 (16) 5.81(148) 1.63 (41)
1/2” 3.50 (89) 7.00 (178) 7.69 (195) 3.25 (83) 0.28 (7) 4.22 (107) 4.00 (102) 0.63 (16) 5.81(148) 1.63 (41)
1” 4.50 (114) 9.00 (229) 10.69 (272) 4.00 (102) 0.34 (9) 5.84 (148) 5.00 (127) 1.00 (25) 8.81(224) 2.03 (52)

Product Configurator Example: 414 1 R 9 A C 3

Series
414 Basic 3 position 4 way

Port Size Operating Pressure Options

1 1/4” NPT ports 9 10,000 psi -MC Spring centering *

3 1/2” NPT ports -MS SAE Porting

5 1” NPT ports * Not available on 1” ported valves

Service

Style A Air, lubricated water or hydraulic oil

R Regular (side) porting

Position
Flow Pattern
3 Three position
C Closed center

O Open center (tandem center)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0038-E • 11/08 • ©2008 • Printed in the U.S.A. 2
 MicrotorqueTM Valve
Features
Valves 518, 526 Series
Original Shear-Seal® technology
Compact design
Non-interflow option
Spring return option
Multiple handle types
2 or 3 position detent

Applications
Work holding clamps and systems
Hydraulic presses and lifting systems
Hydraulic test equipment
Grease injection equipment
Hydraulic power units

General Specifications*
Media: Hydraulic oil Detent:
Working Pressure: 6,000 psi (415 bar) ** 2-position: Detent at 90° positions

Flow Capacity, Cv: See table 3-position: Detents at center and 2 extreme
Back Pressure: Must not exceed 250 psi (17.2 positions
bar)*** at return port for satisfactory Optional Spring Return: Available to center or either
operation shifted position
Proof Pressure: 1-1/2 times working pressure except 5,000 psi (345 bar) max working
at return port pressure on spring return option

Burst Pressure: 2-1/2 times working pressure except Body & Housing: Anodized aluminum
at return port Shaft, Rotor, Pressure 400 series stainless steel
Media Temperature Seals:
-40° to +250°F (-40° to +121°C)
Range: Standard O-Rings: Buna N, others available
Porting: 1/4” NPT, SAE for 1/4” tubing, or DO3 Back-up Rings: Teflon
pattern for manifold mounting Bearings: Hardened steel
Mounting: Panel mountable with p/n 22357 Shipping Weight: .95 lbs
mounting nut (-P option)
DO3 Manifold mounting shipped with
(4) #10-24 screws and O-Rings
Handle Rotation: 90°; 45° each side of center position OPEN (TANDEM) CENTER
PRESS PRESS PRESS
* See product configurator for additional options.
** Consult factory for pressure up to 10,000 psi (690 bar) CYL 2 CYL 1 CYL 2 CYL 1 CYL 2 CYL 1
*** For requirements in excess of 250 psi (17.2 bar) at return port consult factory
RET RET RET

CLOSED CENTER MANIPULATOR 2 1

PRESS PRESS PRESS

CYL 2 CYL 1 CYL 2 CYL 1 CYL 2 CYL 1

RET RET RET P R

Flow Capacity (Approx.) CLOSED CENTER
2 1
20 ft/sec 40 ft/sec PRESS PRESS PRESS
(6.1 m/s) (12.2 m/s) Min. Flow Cv CYL 2 CYL 1 CYL 2 CYL 1 CYL 2 CYL 1
gpm (l/min) gpm (l/min) Passage Dia. Factor
P R RET RET RET
518 Series
1.4 (5.6) 2.8 (11) 0.17" 0.40 2 1
Interflow
526 Series
0.36 (1.4) 0.72 (2.7) 0.086" 0.09
Non-Interflow
P R

1
MicrotorqueTM Valve 518, 526 Series
Technical Drawings
PANEL M
"PRESSURE" E J
PORT 1.062 1.125 F (4 PLACES) N
"PRESSURE"
(27) (29)
"CYL.1" PORT PORT "CYL.2" PORT
"CYL.2" PORT

.562 (14) 1.437

C G PANEL CUTOUT P
1.125 (37)
(29) D H
1.0
(25)

"CYL.1" PORT "RETURN" PORT

Q
"RETURN" PORT .562 (14)
.250
(7)
MAX. PANEL
ø 1.250 THICKNESS
REGULAR (SIDE) PORTING STRAIGHT (BOTTOM) PORTING (31.8)
L
K

Regular and Straight Porting

1.594 Ø.16 X .16 DEEP
"PRESSURE" (40.5)
PORT .850 .450 "CYL.2" PORT J
(21.6) (11.4) (4 PLACES)
.820 (20.8) B
2.375 (60.3)

P
1.220 1.260
A
(31.0) .410 (32.5)
.610 (10.4) .640
(15.9) (16.3)

"CYL.1" PORT .206 THRU (5.2)

.345 Q
(8.8) 4 PLACES M
"RETURN" PORT .690
1.312
(17.5) (33.3)
MANIFOLD PORTING
(Mounting per DO3 Spec)
L
ø 1.250 Optional Knob (-E)
(31.8) K

Series Porting A B C D E F G H J K L M N P Q
21R , 61S Porting 1.968 2.031 1.281 .640 1.594 .850 1.219 .610 1/4-28 3.812 1.437 1.781 .437 1.375 3.125
518 (50.0) (51.6) (32.5) (16.3) (40.5) (21.6) (31.1) (15.5) UNF (96.8) (36.5) (45.2) (11.1) (34.9) (79.4)
or 41M Manifold Porting 1.968 2.031 10-24 3.875 1.437 1.406 1.375 3.125
526 (50.0) (51.6) UNC (98.4) (36.5) (29.0) (34.9) (79.4)
Spring Return Option 5.562 2.500 5.437
(141.3) (63.3) (138.1)

Product Configurator Example: 518 41M 6 H C 3

Series
Position
518 Interflow
-Zxx Optional O-ring material 2
526 Non-interflow
Working Media
H Hydraulic oil Options
Porting
-MC Spring return to center 1
21R Regular (side) porting
Flow Pattern Spring return to right
-MR
41M Manifold porting (D03) (Pressure port to C1) 1
C 4-way closed center
Straight (bottom) Spring return to left
61S O 4-way open center -ML
Porting (Pressure port to C2) 1
4-way manipulator
M -MS SAE porting for 1/4” tubing
Closed center
Pressure Range Black knob (not available
-E
Detent Position with spring return)
6 6,000 psi
Panel mounting nut p/n
2 2-position 90° rotation -P
22357
1
5,000psi max working pressure for spring return option 3 3-position
2
See supplemental guide for the appropriate “Z number”

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0020-E • 09/07 • ©2007 • Printed in the U.S.A. 2
 Shear-Seal® Directional Control
Features
Original Shear-Seal® technology
Valves Series 422 Solenoid Valve

Explosion-Proof option
Zero-leakage*
Spring close with no power
Flexible flow patterns
Tolerates contaminates

Applications
Mining operations
Offshore oil platforms
Refineries and chemical processing plants
Power generation facilities
Air or hydraulic test equipment
General Specifications**
Working Pressure: Air (pneumatic) up to 1,500 psi (103 Electrical Data:
bar) Solenoid Voltage: 115V AC at 60 Hz
Hydraulic oil or lubricated water, up to (Alternative AC & DC voltages are
3,000 psi (206 bar) available).
Pressure Drop: 9 psi at 2.5 gpm
32 psi at 4 gpm Current - Inrush: 16.8 amps
(For more detailed pressure drop and
flow capacity information, see valve Current - Holding: 1.52 amps
supplemental guide) Voltage Tolerance: ±10% of rated voltage
Max. Fluid Velocity: 20ft/sec (6.1 m/sec) Solenoid Rating: Continuous duty
Cv Factor: 0.7 Material of Construction:
Min. Flow Diameter: 7/32 in. (5.6mm) Slide: 400 series stainless steel

Back Pressure: Must not exceed 250 psi (17.2 bar) at Body & Pressure Fittings: Bronze
return port for satisfactory operation
Proof Pressure: 1-1/2 times working pressure except Pressure Seals: Stainless Steel
at return port
Standard O-Ring: Buna N
Burst Pressure: 2-1/2 times working pressure except
at return port (3000 psi [206 bar])
Back-up Rings: Teflon®
Media Temperature -40° to +250°F (-40° to +121°C)
Shipping Weight: 11.5 Lbs. / Explosion-Proof 20 Lbs.
Range:
* Less than four cc per minute
** See product configurator for additional options.

3-Way Shut-Off
Flow Pattern 4-Way Diverter
Norm. Open Norm. Closed Norm. Open Norm. Closed
*Plug Port Cyl. 2 Cyl. 1 Ret. & Cyl. 2 Ret. & Cyl. 1
Marked “X” None Ret.

Normal
Position
Spring Loaded

Energized
Position

ASA Symbol

These Flow Patterns are obtainable from a single Standard Valve. Every valve is shipped with the necessary plugs
*To acheive the desired flow pattern, plug ports as shown.

1
 Shear-Seal® Directional Control Series 422 Solenoid Valve
Technical Drawings

Porting: 3/8” NPT except return port 1/2” NPT

Solenoid A B C D E F G H J K L M N P
11.562 1.312 3.875 1.625 .75 .75 1.50 1.156 2.875 1.281 4.125 1.187 .593 5.5
422
(293.7 (32.5) (98.4) (41.3) (19.1) (19.1) (38.1) (29.4) (73.0) (32.5) (104.8) (30.2) (15.1) (138.7)
14.437 3.593 3.875 1.625 .75 .75 1.50 1.156 2.875 1.281 5.00 1.187 .593 8.375
X422
(366.7) (91.3) (98.4) (41.3) (19.1) (19.1) (38.1) (29.4) (73.0) (32.5) (127) (30.2) (15.1) (212.7)

Product Configurator Example: 422S3WS2A1

Prefix
X Explosion-proof solenoid cover (optional)

Part Number
422S3WS2A1 Oil or lubricated water, 3,000 psi max, 115V AC

422S3AS2A1 Air , 1,500 psi, 115V AC

Alternative voltage and DC Solenoids are available. Consult factory for more detail

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0039-E • 11/08 • ©2008 • Printed in the U.S.A. 2
 1/2” Heavy Duty Hydraulic Regulator
Features
Valves Series 20313

Original Shear-Seal® technology

Self adjusting
High flow capacity
Tolerates contaminated media
Fail-safe motor control options

Applications
BOP Control Units
Coiled tube reels
Oil and gas systems
Pressure sensitive applications

General Specifications*
Pressure: Materials of Construction:
Supply/Inlet Pressure: 5,000 psi (345 bar) Body: Stainless Steel (standard)

Regulated Pressure Range: Flanges: Carbon Steel (standard)

High Sensitivity 300 - 1600 psi (21 -110 bar) Option: Stainless steel
Full Range 300 - 3000 psi (21 - 207 bar)
Spring Tower Housing:
Regulated Pressure Range Manual: Phosphate coated alloy steel (std.)
“F” Prefix Pneumatic Pneumatic Motor model: Phosphate coated alloy steel (std.)
failsafe motor: Hydraulic Motor model: Phosphate coated alloy steel (std.)
High Sensitivity 300 - 1600 psi (21 -110 bar) Option: Stainless Steel
Full Range 300 - 3000 psi (21 - 207 bar)
Standard O’ring Material: Buna N
Regulated Pressure Range
“G” Prefix Hydraulic Socket Head Screws: Zinc plated alloy steel (standard)
failsafe motor: Option: Stainless steel
High Sensitivity 300 - 1600 psi (21 -110 bar)
Full Range 300 - 3000 psi (21 - 207 bar) Wetted Parts: Stainless steel & bronze
Pneumatic Pilot Motor
Fluid Temperature Range: -40° to +250°F (-40° to +121° C) (“F” prefix):
Pilot Motor Working Pressure: 80 - 120 psi (5.5 - 8.3 bar)
Proof Pressure: 7,500 psi (517 bar)
Porting: 1/4” NPT
Flow:
Flow Rate: 45 GPM (@ 50/ft/s) Operating Temperature Range: 32° to +250°F (0° to +120°C)

Cv Inlet: 6.7 Hydraulic Pilot Motor

(“G” prefix):
Pilot Motor Working Pressure: 400 - 1600 PSI (6.9 - 110 bar)
Cv Vent: 6.7
Porting: Porting: SAE for 3/8” Tube (Size -6)
Inlet: 1/2” NPT Standard, SAE Option
Operating Temperature Range: -40° to +250°F (-40° to +121°C)
Outlet: 1/2” NPT Standard, SAE Option Approximate Shipping Weight:
Manual: 21 lbs. (9.5 kg)
Vent: 1/2” NPT Standard, SAE Option
Pneumatic or Hydraulic
Bleed Port: 1/4” Dia. hole Motor: 44 lbs. (20.0 kg)
* See product configurator for additional options.

1
1/2” Heavy Duty Hydraulic Regulator Series 20313
Technical Drawings

7.968
7.125 (202.2)

15.188 3.500

2.250
1/8” NPT 18.938
BLEED PORT (481)

19.125
1.750 MAX(485.8)
9.281
(235.7)
4.500
1.75
1.500 2.375 (44.5)

4.750

2.500
2.500 (63.5)

.250 2.500
.250 1.562
(63.5)
2.250

Dimensions in inches (mm)

Product Configurator Example: 20313S6WQ2

Option
Blank NPT porting
-MS SAE porting
-SS Stainless Steel Flanges & Trim

Adjustment Method
Blank Manual
Regulated Pressure Range (Manual)
F Pneumatic motor
Blank High sensitivity 300 - 1600 psi (21 -110 bar)
G Hydraulic motor
-1 Full range 300 - 3000 psi (21 - 207 bar)

Regulated Pressure Range (Failsafe)

(F or G models)
Series
Blank High sensitivity 300 - 1600 psi (21 -110 bar)
20313S6WQ2 1/2” Shear-Seal Regulator
-1 Full range 300 - 3000 psi (21 - 207 bar)

3211 Fruitland Avenue • Los Angeles, CA 90058 • 800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0026-F • 03/11 • ©2011 • Printed in the U.S.A. 2
 3/4” Hydraulic Regulator
Features
Valves Series 20415

Original Shear-Seal® technology

Self adjusting
High flow capacity
Tolerates contaminated media
Fail-safe motor control options
Self venting

Applications
Coiled tube reels
Land-based oil drilling controls
BOP control units

General Specifications*
Pressure: Materials of Construction:
Supply/Inlet Pressure: 3,000 psi (207bar) Body: Phosphate coated alloy steel (std.)
Option: Stainless steel
Regulated Pressure Range:
High Sensitivity 500 - 1600 PSI (34 -110 bar) Flanges: Phosphate coated alloy steel (std.)
Full Range 500 - 2800 PSI (34 - 193 bar) Option: Stainless steel

Regulated Pressure Range Spring Tower:

“F” Prefix Pneumatic Manual Phosphate coated alloy steel (std.)
failsafe motor: Pneumatic Motor model Painted alloy steel (std.)
High Sensitivity 500 - 1600 PSI (34 -110 bar) Hydraulic Motor model Painted alloy steel (std.)
Full Range 500 - 2800 PSI (34 - 193 bar) Option: Stainless steel

Regulated Pressure Range Standard O’ring Material: Buna N

“G” Prefix Hydraulic
failsafe motor: Socket Head Screws: Zinc plated alloy steel (std.)
High Sensitivity 500 - 1600 PSI (34- 110 bar) Option: Stainless steel
Full Range 500 - 2800 PSI (34 - 193 bar)
Wetted Parts: Stainless steel & bronze
Fluid Temperature Range: -40° to +250°F (-40° to +121°C)
Pneumatic Pilot Motor
Proof Pressure: 4,500 PSI (310 bar) (“F” prefix):
Pilot Motor Working Pressure: 80 - 120 PSI (5.5 - 8.3 bar)
Flow:
Flow Rate: 70 GPM (@ 50 ft/s) Porting: 1/4” NPT

Cv Inlet: 9.8 Operating Temperature Range: 32° to +250°F (0° to +120°C)

Cv Vent: 0.6 Hydraulic Pilot Motor

(“G” prefix):
Porting: Pilot Motor Working Pressure: 400 - 1600 PSI (6.9 - 110 bar)
Inlet 1: 1” NPT Standard, SAE Optional
Porting: SAE for 3/8” Tube (Size -6)
Outlet (regulated): 1” NPT Standard, SAE Optional
Operating Temperature Rating: -40° to +250°F (-40° to +121°C)
Vent: 1/2” NPT Standard, SAE Optional
Approximate Shipping Weight:
3/8” NPT Standard, SAE Optional Manual: 47 lbs. (21.3 kg)
Gauge Port:
* See product configurator for additional options. Pneumatic or Hydraulic
Motor: 70 lbs. (31.8 kg)

1
3/4” Hydraulic Regulator Series 20415
Technical Drawings

7.125

3.500

25.625
(652)
25.625
.500 (652)
16.625
(423)
4.500

3.312 21.500
1.375
6.063
2.875 4.562
2.125

5.188 6.875 1.562

Dimensions in inches (mm)

Product Configurator Example: 20415S3WQ2

Option
Blank NPT porting
-MS SAE porting
Adjustment Method
-SS Stainless steel flanges & trim
Blank Manual
F Pneumatic failsafe motor
G Hydraulic failsafe motor
Regulated Pressure Range (Manual)
Blank High sensitivity 500 - 1600 psi (34 - 110 bar)
Series
-1 Full range 500 - 2800 psi (34 - 193 bar)
20415S3WQ2 1” Pressure regulator
Regulated Pressure Range (Failsafe)
F & G Models
Blank High sensitivity 500 - 1600 psi (34 - 110 bar)

-1 Full range 500 - 2800 psi (34 - 193 bar)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0025-G • 02/11 • ©2011 • Printed in the U.S.A. 2
3/4” Heavy Duty Hydraulic Regulator
Features
Valves Series 20495

Original Shear-Seal® technology

Ultra flow regulator
API compliant for sensitivity
Fail-safe motor control options
Tolerates contaminated media
Self venting
Surge dampening

Applications
Coiled tube reels
Land-based and offshore oil drilling controls
Wireline service tractors
Pressure sensitive applications

General Specifications*
Pressure: Materials of Construction:
Supply/Inlet Pressure: 5,000 psi (345 bar) Body: Stainless steel (standard)

Regulated Pressure Range: Flanges: Phosphate coated alloy steel (std.)

High Sensitivity 500 - 1800 PSI 34 - 124 bar) Option: Stainless steel
Full Range 500 - 3300 PSI (34 - 228 bar)
Spring Tower:
Regulated Pressure Range Manual Phosphate coated alloy steel (std.)
“F” Prefix Pneumatic Pneumatic Motor model Painted alloy steel (std.)
failsafe motor: Hydraulic Motor model Painted alloy steel (std.)
High Sensitivity 500 - 1800 PSI (34 - 124 bar) Option: Stainless steel
Full Range 500 - 3000 PSI (34 -207 bar)
Standard O’ring Material: Buna N
Regulated Pressure Range
“G” Prefix Hydraulic Socket Head Screws: Zinc plated alloy steel (std.)
failsafe motor: Option: Stainless steel
High Sensitivity 500 - 1800 PSI (34 - 124 bar) Wetted Parts: Stainless steel & bronze
Full Range 500 - 3000 PSI (34 - 207 bar)
Pneumatic Pilot Motor
(“F” prefix):
Fluid Temperature Range: -40° to +250°F (-40° to +121°C) Pilot Motor Working Pressure: 80 - 120 PSI (5.5 - 8.3 bar)

Proof Pressure: 7,500 psi (517 bar) Porting: 1/4” NPT

Flow: Operating Temperature Range: 32° to +250°F (0° to +120°C)

Flow Rate: 90 GPM (@ 50 ft/s)
Hydraulic Pilot Motor
Cv Inlet: 9.8 (“G” prefix):
Pilot Motor Working Pressure: 400 - 1600 PSI (6.9 - 110 bar)
Cv Vent: 0.7
Porting: SAE for 3/8” Tube (Size -6)
Porting:
Inlet 1: 1” NPT Standard, SAE Optional Operating Temperature Rating: -40° to +250°F (-40° to +121°C)
Approximate Shipping Weight:
Outlet (regulated): 1” NPT Standard, SAE Optional
Manual: 47 lbs. (21.3 kg)
Vent: 1/2” NPT Standard, SAE Optional
Pneumatic or Hydraulic
Motor: 70 lbs. (31.8 kg)
Gauge Port: 3/8” NPT Standard, SAE Optional
* See product configurator for additional options.

1
 3/4” Heavy Duty Hydraulic Regulator Series 20495
Technical Drawings

7.125

3.500

26.382
(670.1)
26.382
.500 (670.1)

4.500

3.312 22.670
1.375 (575.8)
6.063
2.875 4.562
2.177

5.187 6.875
1.562

Dimensions in inches (mm)

Product Configurator Example: 20495S6WQ2

Option
Blank NPT porting
-MS SAE porting
Adjustment Method
-SS Stainless steel flanges & trim
Blank Manual
F Pneumatic failsafe motor
Regulated Pressure Range (Manual)
G Hydraulic failsafe motor
Blank High sensitivity 500 - 1800 psi (34 - 124 bar)
-1 Full range 500 - 3300 psi (34 - 228 bar)
Series
Regulated Pressure Range (Failsafe)
20495S6WQ2 1” Pressure regulator
F & G Models
Blank High sensitivity 500 - 1800 psi (34 - 124 bar)
-1 Full range 500 - 3000 psi (34 - 207 bar)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0056-I • 02/11 • ©2011 • Printed in the U.S.A. 2
 1-½” Hydraulic Regulator
Features
Valves Series 20517

Original Shear-Seal® technology

High flow capacity
Large pressure range
Tolerates contaminated media
Fail-safe motor control options
Self venting

Applications
Land-based hydraulic drilling controls
BOP control units
Hydraulic powered tube reels

General Specifications*
Pressure: Materials of Construction:
Supply/Inlet Pressure: 3,000 psi (207 bar) Body: Phosphate coated alloy steel (std.)
Option: Stainless steel
Regulated Pressure Range:
High Sensitivity 200 - 1600 PSI (14 -110 bar) Flanges: Phosphate coated alloy steel (std.)
Full Range 350 - 2800 PSI (24 - 193 bar) Option: Stainless steel

Regulated Pressure Range Spring Tower:

“F” Prefix Pneumatic Manual: Stainless steel (std.)
failsafe motor: Pneumatic Motor model: Painted alloy steel (std.)
High Sensitivity 200 - 1600 PSI (14 - 110 bar) Hydraulic Motor model: Painted alloy steel (std.)
Full Range 350 - 2800 PSI (24 - 193 bar) Option: Stainless steel

Regulated Pressure Range Standard O’ring Material: Buna N

“G” Prefix Hydraulic
failsafe motor: Socket Head Screws: Stainless steel (std.)
High Sensitivity 200 - 1600 PSI (14 -110 bar)
Full Range 350 - 2800 PSI (24 - 193 bar) Wetted Parts: Stainless steel & bronze

Fluid Temperature Range: -40° to +250°F (-40° to +121°C) Pneumatic Pilot Motor
(“F” prefix):
Proof Pressure: 4,500 psi (310 bar) Pilot Motor Working Pressure: 80 - 120 PSI (5.5 - 8.3 bar)

Flow: Porting: 1/4” NPT

Flow Rate: 120 GPM (@ 50 ft/s)
Operating Temperature Range: 32° to +250°F (0° to +120°C)
Cv Inlet: 17.5
Hydraulic Pilot Motor
Cv Vent: 1.6 (“G” prefix):
Pilot Motor Working Pressure: 400 - 1600 PSI (6.9 - 110 bar)
Porting:
Inlet 1: 1” NPT Standard, SAE Optional Porting: SAE for 3/8” Tube (Size -6)

Inlet 2: 1” NPT Standard, SAE Optional Operating Temperature Rating: -40° to +250°F (-40° to +121°C)

1-1/2” NPT Standard, SAE Optional Approximate Shipping

Outlet:
Weight: 67 lbs. (30.4 kg)
Vent: 1” NPT Standard, SAE Optional Manual:

* See product configurator for additional options. 90 lbs. (40.8 kg)

Pneumatic or Hydraulic
Motor:

1
 1-½” Hydraulic Regulator Series 20517
Technical Drawings
7.125

3.500

26.382
(670.1)
26.382
(670.1)

4.500

2.177

1.562

Dimensions in inches (mm)

Product Configurator Example: 20517S3WQ2

Option
Blank NPT porting
-MS SAE porting
Adjustment Method
-SS Stainless steel flanges & trim
Blank Manual
F Pneumatic failsafe motor
Regulated Pressure Range (Manual)
G Hydraulic failsafe motor
Blank High sensitivity 200 - 1600 psi (14 - 110 bar)
-1 Full range 350 - 2800 psi (24 - 193 bar)
Series
Regulated Pressure Range (Failsafe)
20517S3WQ2 1-1/2” Pressure regulator
F & G Models
Blank High sensitivity 200 - 1600 psi (14 - 110 bar)
-1 Full range 350 - 2800 psi (24 - 193 bar)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0061-C • 02/11 • ©2011 • Printed in the U.S.A. 2
 1-½” Heavy Duty Hydraulic Regulator
Features
Valves Series 20597

Original Shear-Seal® technology

API compliant for sensitivity
High flow capacity
Large pressure range
Tolerates contaminated media
Fail-safe motor control options
Self venting
Surge dampening

Applications
Land-based and offshore oil drilling controls
l
BOP control units
Pressure sensitive equipment

General Specifications*
Pressure: Materials of Construction:
Supply/Inlet Pressure: 5,000 psi (345 bar) Body: Stainless steel (std.)

Regulated Pressure Range: Flanges: Phosphate coated alloy steel (std.)

High Sensitivity 300 - 1600 psi (21 -110 bar) Option: Stainless steel
Full Range 500 - 3300 psi (34 - 228 bar)
Spring Tower:
Regulated Pressure Range Manual: Stainless steel (std.)
“F” Prefix Pneumatic Pneumatic Motor model: Painted alloy steel (std.)
failsafe motor: Hydraulic Motor model: Painted alloy steel (std.)
High Sensitivity 300 - 1600 psi (21 - 110 bar) Option: Stainless steel
Full Range 500 - 3000 psi (34 - 207 bar)
Standard O’ring Material: Buna N
Regulated Pressure Range
“G” Prefix Hydraulic Socket Head Screws: Stainless steel (std.)
failsafe motor:
High Sensitivity 300 - 1600 psi (21 -110 bar) Wetted Parts: Stainless steel
Full Range 500 - 3000 psi (34 - 207 bar)
Pneumatic Pilot Motor
Fluid Temperature Range: -40° to +250°F (-40° to +121°C) (“F” prefix):
Pilot Motor Working Pressure: 80 - 120 psi (5.5 - 8.3 bar)
Proof Pressure: 7,500 psi (517 bar)
Porting: 1/4” NPT
Flow:
Flow Rate: 120 GPM (@ 50 ft/s) Operating Temperature Range: 32° to +250°F (0° to +120°C)

Cv Inlet: 17.5 Hydraulic Pilot Motor

(“G” prefix):
Cv Vent: 2.6 Pilot Motor Working Pressure: 400 - 1600 psi (6.9 - 110 bar)

Porting: Porting: SAE for 3/8” Tube (Size -6)

Inlet 1: 1” NPT Standard, SAE Optional
Operating Temperature Rating: -40° to +250°F (-40° to +121°C)
Inlet 2: 1” NPT Standard, SAE Optional
Approximate Shipping Weight:
1-1/2” NPT Standard, SAE Optional Manual: 67 lbs. (30.4 kg)
Outlet:

1” NPT Standard, SAE Optional Pneumatic or Hydraulic

Vent:
Motor: 90 lbs. (40.8 kg)
* See product configurator for additional options.

1
1-½” Heavy Duty Hydraulic Regulator Series 20597
Technical Drawings
7.125

3.500

26.382
(670.1)
26.382
(670.1)

4.500

2.177

1.562

Dimensions in inches (mm)

Product Configurator Example: 20597S6WQ2

Option
Blank NPT porting
-MS SAE porting
-SS Stainless steel flanges & trim
Adjustment Method
Blank Manual
Regulated Pressure Range (Manual)
F Pneumatic motor Blank High sensitivity 300 - 1600 psi (21 - 110 bar)
G Hydraulic motor -1 Full range 500 - 3300 psi (34 - 228 bar)

Regulated Pressure Range (Failsafe)

F & G Models
Series
Blank High sensitivity 300 - 1600 psi (21 - 110 bar)
20597S6WQ2 1-1/2” Pressure regulator -1 Full range 500 - 3000 psi (34 - 207 bar)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0060-C • 02/11 • ©2011 • Printed in the U.S.A. 2
 Pressure Relief Valve
Valve Series 8010

Features
High flow with Zero Leak
Extended seat life
Factory pre-set or field adjustable
Optional tamper-proof cap
Stainless steel internals
Metal-to-metal seal

Applications
Pump system safety
Compressor over pressure protection
Hydraulic power units
Tank protection
Accumulator systems

General Specifications*
Working Pressure: Hydraulic oil up to 5500 psi (380 bar) Flow Rate at 10% above Cracking Pressure
6000
Proof Pressure: 10,000 psi (690 bar)
5000 psi C.P. (-4)
Pressure Ranges: 500 - 1500 psi (35 - 105 bar) 5000
1500 - 3500 psi (105 - 240 bar)
Pressure Drop (PSI)

3500 - 5500 psi (240 - 380 bar) 4000

3000 psi C.P. (-3)
Flow Rate: 15 GPM (NOMINAL) 3000
Wetted Material:
Process Fitting: Heat-treated 410 stainless steel 2000

1500 psi C.P. (-2)

Internals: 416 stainless steel 1000

Spring: Powder-coated high strength steel 0

0 2 4 6 8 10 12 14 16
Ball: Tungsten Carbide Flow (GPM)

Housing: Powder-coated ductile iron

Typical 8014 Lift Characteristics
Weight: 2.5 lbs. 120

Pressure Connection: 3/4” NPTM x 3/4” NPTF 100

Temperature Range: -40° to +200°F (-40° to +93°C)

80
Full Open %

Pressure Settings: It is recommended that cracking Full Open

pressure be set 10% above working 60
Significant
pressure. Vent
40
Pressure Setpoint Loosen hex nut with open-end wrench.
First Weep
Adjustment: Using allen key turn adjustment screw
20
clockwise to increase, counterclock-
wise to decrease set point.
0
* See product configurator for additional options. 90 95 100 105 110 115 120
Set Pressure %

1
Pressure Relief Valve Series 8010

Technical Drawings
(OPTIONAL) 2.1
TAMPER-PROOF CAP [ 52.39 ]
MAX

OVERALL
7.0 6.0
[ 178 ] 3/4 NPT FEMALE [ 152 ]
OUTLET

OUTLET PORT
CL 2.59
[ 65.67 ]
INLET PORT

1.63 3/4 NPT MALE INLET

[ 41.3 ]
WRENCH
FLATS

Product Configurator Example: 801 4 -3 -33

Prefix
T Tamper-proof cap (optional)

Base Model Housing Option

801 Inlet male - outlet Female Porting Corrosion Resistant Ductile
Blank
Iron (standard)
SS Stainless Steel
Port Size
4 3/4” NPT ports

Pressure Range

Adjustable Range Approx. Proof

Blowdown Pressure
Factory Set Point
psi (bar)
Min. Max. psi (bar) psi (bar) Blank Field Adjustable

-2 500 (35) 1500 (105) 200 (15) 10,000 (690) Insert desired set point
-3 1500 (105) 3500 (240) 400 (28) 10,000 (690) -XX in 00’s (ex. 3300 psi = -33

-4 3500 (240) 5500 (380) 600 (42) 10,000 (690) 700 psi = -07)

3211 Fruitland Avenue • Los Angeles, CA 90058 •  800-835-1060 • Fax: 323-589-3463 • www.barksdale.com
2
See Barksdale’s Standard Conditions of Sale • Specifications are subject to modification at any time • Bulletin #B0051-D • 08/08 • ©2008 • Printed in the U.S.A.
 Hydraulic Relief Valve
Installation and Operating Instructions Model 8014
Description: Field Adjustment of Relief Pressure Set Point:
This is a hydraulic pressure relief valve having a
factory set or field-adjustable set point. The valve is 1. Tools Required:
designed to work with hydraulic oil-based media. x Allen key 5/16 inch
This valve is not intended for water or steam-based x Torque wrench
applications. Standard wetted materials include x Open end wrench 15/16 inch
stainless steel, ductile iron, steel and Buna-N. 2. Adjustment Procedures:
x Use 15/16 inch open end wrench to loosen
Caution: locking nut by turning it counter clockwise
The recommendations below are general and it is (CCW).
the responsibility of the user to assure that x Insert Allen key to top of adjustment stud
installation and maintenance are in accordance with and rotate it counter clockwise (CCW) to
local requirements and ASME practices. This valve decrease set pressure. Turn it clockwise
should be installed by a trained service person. A (CW) to increase set pressure.
media filter should be in the system to protect the x Re-tighten anti-vibration locking nut firmly
valve. Neither Barksdale nor its agents assume any against flat valve body and torque with a
liability for valves improperly used in the torque wrench to 300 in-lb.
application or improperly installed and maintained. Caution: Failure to torque locking nut to
specified value can cause malfunction,
Installation: failure of relief pressure, or injury.
Mounting: Valve shall be mounted in a vertical
position and connected in the flow
direction shown by the arrow. Use Adjustment Allen Key
wrench flat 1 5/8 inch to secure valve to Stud
pipe line.

Piping: Support with adequate piping in order to

avoid excessive shock and vibration.
Valve inlet is 3/4” NPT male and the Locking
outlet is 3/4” NPT female. It is Nut
~ 6 inch
(Torque to
recommended that a minimum of 1/2”
300 in-lb.)
pipe size to be used for the inlet and the
outlet connection.
Flow
Ambient Temperature: -40°F to 200°F
Direction
Operating Pressure Range (PSIG):

Adjustable Pressure Tolerance 2.1 inch

Range Range (psi) ± ( psi)
Code
For service or ordering information:
-1 200 - 500 50
Consult factory or authorized factory representative.
-2 500 - 1500 150
Specify full catalog number (with any optional
-3 1500 - 3500 350
modification) and factory set point.
-4 3500 - 5500 550

_________________________________________________________________________________________
Barksdale, Inc. 3211 Fruitland Avenue, Los Angeles CA 90058 (800)835-1060 www.barksdale.com Bulletin No. 272233-A 12-7-06

20
 Global Presence
Global Presence

Barksdale Inc. Barksdale GmbH Barksdale GmbH Barksdale India

3211 Fruitland Ave. Dorn-Assenheimer Strasse 27 Dorn-Assenheimer Strasse 27 SF- 43, Ansal Fortune Arcade
Los Angeles, CA 90058-0843 61203 Reichelsheim, Germany 61203 Reichelsheim, Germany Sector – 18
U.S.A. Phone: (49) 6035-949-0 (main office) Phone: (49) 6035-949-0 (main office) India-201301 Noida
Phone: (800) 835-1060 (49) 6035-949-204 (sales) (49) 6035-949-204 (sales) Phone: +91-120 25 10 522
Fax: (323) 589-3463 Fax: (49) 6035-949-111/-113 Fax: (49) 6035-949-111/-113 Fax: +91-120 25 10 520
Email: [email protected] Email: [email protected] Email: [email protected] [email protected]
www.barksdale.com www.barksdale.de www.barksdale.de