Worldwide

www.tyco-fire.com
Contacts

G-FIRE Grooved Fittings

Ductile Iron and Fabricated Steel Ductile

IMPORTANT NOTICE
Refer to Technical Data Sheet Never remove any piping component
TFP2300 for warnings pertaining to nor correct or modify any piping defi-
regulatory and health information. ciencies without first de-pressurizing
and draining the system. Failure to do
so may result in serious personal injury,
Scan the QR code or enter the URL property damage, and/or impaired
in a web browser to access the most device performance.
up-to-date electronic version of this It is the designer’s responsibility
document. Data rates may apply. to select products suitable for the
intended service and to ensure that
pressure ratings and performance
data are not exceeded. Material and
gasket selection should be verified to
be compatible for the specific applica-
tion. Always read and understand the
installation instructions.
The GRINNELL G-FIRE Grooved
Fittings described herein must be
installed and maintained in compliance
with this document, as well as with the
applicable standards of the approval
agency, in addition to the standards of
docs.jci.com/tycofire/tfp1815 any other authorities having jurisdiction.
Failure to do so may result in serious
personal injury or impair the perfor-
General mance of these devices.
Internal fitting coatings serving as pro-
Description tection during storage and transport
can become separated after installation
GRINNELL G-FIRE Grooved Fittings
provide an economical and efficient
and during system operation, poten-
tially causing blockage of strainers or
Technical
method of changing direction, adding
an outlet, reducing, or capping piping
other filtering equipment. If strainers
are installed in the piping system the Data
systems. The G-FIRE grooved fittings manufacturer recommends they feature Approvals
are available in ductile iron or fabri- a minimum 5/32 in. (4 mm) mesh size UL and ULC Listed
cated steel as indicated. and, to prevent blockages, that they FM Approved
are regularly serviced at intervals to be VdS Approved
Note: Figure 510S and 519S fittings are determined by the system designer. LPCB Certified
special short radius fittings with smaller
center to end dimensions than stan- The owner is responsible for maintain- Note: LPCB Certification applies to Figures
ing their system and devices in proper 211, 212, 221, 250, 260, 501, 510, 511, 512,
dard grooved fittings. Depending on 519, 550, 510S, and 519S.
the size and coupling used, there may operating condition. Contact the install-
be interferences at the bolt pads that ing contractor or product manufacturer Material
require repositioning of the coupling with any questions Cast: Ductile iron conforming to ASTM
A536, Grade 65-45-12
orientation. The use of flange adapters
is not recommended with Figures 510S Fabricated Steel: Carbon Steel conforming
and 519S fittings. Contact Johnson to ASTM A53, ASTM A135, and ASTM
Controls for details. A795
Protective Coatings
• Non-lead orange paint (USA)
• RAL red or non-lead paint (EMEA and
APAC)
• Hot dipped galvanized conforming to
ASTM A153

Page 1 of 26 AUGUST 2022 TFP1815

TFP1815
Page 2 of 26

Figure 250 Figure 350 Figure 550 (a)

Nominal Pipe Size Cast Fabricated Cast

Nominal Approx. Nominal Approx. Nominal Approx.

O.D.
ANSI Inches E to E Weight E to E Weight E to E Weight
Inches
(DN) Inches Lbs. Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg) (mm) (kg)
1-1/4 x 1 1.66 x 1.31 2.50 0.7 2.50 0.7
— —
(32 x 25) (42,4 x 33,4) (63,5) (0,3) (63,5) (0,3)
1-1/2 x 1 1.90 x 1.31 2.50 0.7
— — — —
(40 x 25) (48,3 x 33,4) (63,5) (0,3)
1-1/2 x 1-1/4 1.90 x 1.66 2.50 0.8 2.50 0.8
— —
(40 x 32) (48,3 x 42,4) (63,5) (0,3) (63,5) (0,3)
2x1 2.37 x 1.31 2.50 0.9
— — — —
(50 x 25) (60,3 x 33,4) (63,5) (0,4)
E to E 2 x 1-1/4 2.37 x 1.66 2.50 0.9
— — — —
(50 x 32) (60,3 x 42,4) (63,5) (0,4)
2 x 1-1/2 2.37 x 1.90 2.50 1.0
— — — —
(50 x 40) (60,3 x 48,3) (63,5) (0,5)
2-1/2 x 1 2.87 x 1.31 2.50 1.2
— — — —
(65 x 25) (73,0 x 33,4) (63,5) (0,5)
FIGURE 250
CAST CONCENTRIC 2-1/2 x 1-1/4 2.87 x 1.66 2.50 1.4 2.50 1.4
REDUCER — —
(65 x 32) (73,0 x 42,4) (63,5) (0,6) (63,5) (0,6)

E to E 2-1/2 x 1-1/2 2.87 x 1.90 2.50 1.4 2.50 1.4

— —
(65 x 40) (73,0 x 48,3) (63,5) (0,6) (63,5) (0,6)
2-1/2 x 2 2.87 x 2.37 2.50 1.3 2.50 1.3
— —
(65 x 50) (73,0 x 60,3) (63,5) (0,6) (63,5) (0,6)
76,1mm x 1-1/4 3.00 x 1.66 2.50 1.4 2.50 1.4
— —
(65 x 32) (76,1 x 42,4) (63,5) (0,6) (63,5) (0,6)
FIGURE 350
FABRICATED CONCENTRIC 76,1mm x 1-1/2 3.00 x 1.90 2.50 1.4 2.50 1.4
— —
REDUCER (65 x 40) (76,1 x 48,3) (63,5) (0,6) (63,5) (0,6)
76,1mm x 2 3.00 x 2.37 2.50 1.5 2.50 1.5
E to E — —
(65 x 50) (76,1 x 60,3) (63,5) (0,7) (63,5) (0,7)
3x1 3.50 x 1.31 2.50 1.3
— — — —
(80 x 25) (88,9 x 33,4) (63,5) (0,6)
3 x 1-1/4 3.50 x 1.66 2.50 1.3
— — — —
(80 x 32) (88,9 x 42,4) (63,5) (0,6)
FIGURE 550a 3 x 1-1/2 3.50 x 1.90 2.50 1.8 2.50 1.8
CAST CONCENTRIC — —
(80 x 40) (88,9 x 48,3) (63,5) (0,8) (63,5) (0,8)
REDUCER
3x2 3.50 x 2.37 2.50 1.7 2.50 1.7
— —
(80 x 50) (88,9 x 60,3) (63,5) (0,8) (63,5) (0,8)
3 x 2-1/2 3.50 x 2.87 2.50 1.7 2.50 1.7
— —
(80 x 65) (88,9 x 70,3) (63,5) (0,8) (63,5) (0,8)
3 x 76,1mm 3.50 x 3.00 2.50 2.0 2.50 2.0
— —
(80 x 65) (88,9 x 76,1) (63,5) (0,9) (63,5) (0,9)
4x1 4.50 x 1.31 3.00 2.9
— — — —
(100 x 25) (114,3 x 33,4) (76,2) (1,1)
4 x 1-1/4 4.50 x 1.66 3.00 2.2
— — — —
(100 x 32) (114,3 x 42,4) (76,2) (1,0)
4 x 1-1/2 4.50 x 1.90 3.00 2.3
— — — —
(100 x 40) (114,3 x 48,3) (76,2) (1,0)
4x2 4.50 x 2.37 3.00 2.4 3.00 2.4
— —
(100 x 50) (114,3 x 60,3) (76,2) (1,1) (76,2) (1,1)
4 x 2-1/2 4.50 x 2.87 3.00 2.7 3.00 2.7
— —
(100 x 65) (114,3 x 73,0) (76,2) (1,2) (76,2) (1,2)
NOTES
a. Figure 550 is available for the Americas market only.
FIGURE 1 (1 OF 3)
FIGURES 250, 350, AND 550 CONCENTRIC REDUCERS
NOMINAL DIMENSIONS
 TFP1815
Page 3 of 26

Figure 250 Figure 350 Figure 550 (a)

Nominal Pipe Size Cast Fabricated Cast

Nominal Approx. Nominal Approx. Nominal Approx.

O.D.
ANSI Inches E to E Weight E to E Weight E to E Weight
Inches
(DN) Inches Lbs. Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg) (mm) (kg)
4 x 76,1mm 4.50 x 3.00 3.00 3.2 3.00 3.2
— —
(100 x 65) (114,3 x 76,1) (76,2) (1,5) (76,2) (1,5)
4x3 4.50 x 3.50 3.00 2.8 3.00 2.8
— —
(100 x 80) (114,3 x 88,9) (76,2) (1,3) (76,2) (1,3)
139,7mm x 3 5.50 x 3.50 3.50 4.2 3.50 4.2
— —
(125 x 80) (139,7 x 88,9) (88,9) (1,9) (88,9) (1,9)
139,7mm x 4 5.50 x 4.50 3.50 4.4 3.50 4.4
— —
(125 x 100) (139,7 x 114,3) (88,9) (2,0) (88,9) (2,0)
5x2 5.56 x 2.37 3.50 4.6
— — — —
(125 x 50) (141,3 x 60,3) (88,9) (2,1) E to E
5 x 2-1/2 5.56 x 2.87 3.50 4.5
— — — —
(125 x 65) (141,3 x 73,0) (88,9) (2,0)
5x3 5.56 x 3.50 3.50 4.2 3.50 4.2
— —
(125 x 80) (141,3 x 88,9) (88,9) 1,9) (88,9) 1,9)
5x4 5.56 x 4.50 3.50 4.4 3.50 4.4 FIGURE 250
— —
(125 x 100) (141,3 x 114,3) (88,9) (2,0) (88,9) (2,0) CAST CONCENTRIC
165,1mm x 3 6.50 x 3.50 4.00 5.5 4.00 5.5 REDUCER
— —
(150 x 80) (165,1 x 88,9) (101,6) (2,5) (101,6) (2,5)
E to E
165,1mm x 4 6.50 x 4.50 4.00 6.0. 4.00 6.0.
— —
(150 x 100) (165,1 x 114,3) (101,6) (2,7) (101,6) (2,7)
165,1mm x 139,7mm 6.50 x 5.50 4.00 5.6 4.00 5.6
— —
(150 x 125) (165,1 x 139,7) (101,6) (2,5) (101,6) (2,5)
6x1 6.63 x 1.31 4.00 4.7 4.00 4.7
— — FIGURE 350
(150 x 25) (168.3 x 33.7) (101,6) (2,1) (101,6) (2,1)
FABRICATED CONCENTRIC
6 x 1-1/2 6.63 x 1.90 4.00 5.0 4.00 5.0 REDUCER
— —
(150 x 40) (168.3 x 48.3) (101,6) (2,3) (101,6) (2,3)
E to E
6x2 6.63 x 2.37 4.00 5.3 4.00 5.3
— —
(150 x 50) (168,3 x 60,3) (101,6) (2,4) (101,6) (2,4)
6 x 2-1/2 6.63 x 2.87 4.00 5.7 4.00 5.7
— —
(150 x 65) (168,3 x 73,0) (101,6) (2,6) (101,6) (2,6)
6 x 76,1mm 6.63 x 3.00 4.00 6.1 4.00 6.1
— — FIGURE 550a
(150 x 65) (168,3 x 76,1) (101,6) (2,7) (101,6) (2,7)
CAST CONCENTRIC
6x3 6.63 x 3.50 4.00 5.8 4.00 5.8 REDUCER
— —
(150 x 80) (168,3 x 88,9) (101,6) (2,6) (101,6) (2,6)
6 x 108,0mm 6.63 x 4.25 4.00 6.0
— — — —
(150 x 100) (168,3 x 108,0) (101,6) (2,7)
6x4 6.63 x 4.50 4.00 6.0 4.00 6.0
— —
(150 x 100) (168,3 x 114,3) (101,6) (2,7) (101,6) (2,7)
6 x 139,7mm 6.63 x 5.50 4.00 6.3 4.00 6.3
— —
(150 x 100) (168,3 x 139,7) (101,6) (2,3) (101,6) (2,3)
6x5 6.63 x 5.56 4.00 6.2 4.00 6.2
— —
(150 x 125) (168,3 x 141,3) (101,6) (2,8) (101,6) (2,8)
216,3mm x 2-1/2 8.52 x 2.87 5.00 12.1
— — — —
(200 x 65) (216,3 x 73,0) (127,0) (5,5)
8x3 8.63 x 3.50 5.00 11.5 5.00 11.5
— —
(200 x 80) (219,1 x 88,9) (127,0) (5,2) (127,0) (5,2)
8x4 8.63 x 4.50 5.00 10.7 5.00 10.7
— —
(200 x 100) (219,1 x 114,3) (127,0) (4,9) (127,0) (4,9)
NOTES
a. Figure 550 is available for the Americas market only.
FIGURE 1 (2 OF 3)
FIGURES 250, 350, AND 550 CONCENTRIC REDUCERS
NOMINAL DIMENSIONS
TFP1815
Page 4 of 26

Figure 250 Figure 350 Figure 550 (a)

Nominal Pipe Size Cast Fabricated Cast

Nominal Approx. Nominal Approx. Nominal Approx.

O.D.
E to E ANSI Inches E to E Weight E to E Weight E to E Weight
Inches
(DN) Inches Lbs. Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg) (mm) (kg)
8 x 139,7mm 8.63 x 5.50 5.00 10.0 5.00 10.0
— —
(200 x 125) (219,1 x 139.7) (127,0) (4,5) (127,0) (4,5)
8x5 8.63 x 5.56 5.00 10.8 5.00 10.8
— —
FIGURE 250 (200 x 125) (219,1 x 141,3) (127,0) (4,9) (127,0) (4,9)
CAST CONCENTRIC
REDUCER 8 x 165,1mm 8.63 x 6.50 5.00 11.0 5.00 11.0
— —
(200 x 150) (219,1 x 165.1) (127,0) (5,0) (127,0) (5,0)
E to E 8x6 8.63 x 6.63 5.00 11.3 5.00 11.3
— —
(200 x 150) (219,1 x 168,3) (127,0) (5,1) (127,0) (5,1)
10 x 4 10.75 x 4.50 6.00 20.5
— — — —
(250 x 100) (273,0 x 114,3) (152,4) (9,3)
10 x 5 10.75 x 5.56 6.00 20.1
— — — —
FIGURE 350 (250 x 125) (273,0 x 141,3) (152,4) (9,1)
FABRICATED CONCENTRIC 10 x 165,1mm 10.75 x 6.50 6.00 17.8 6.00 17.8
REDUCER — —
(250 x 150) (273,0 x 165,1) (152,4) (8,0) (152,4) (8,0)
E to E 10 x 6 10.75 x 6.63 6.00 16.3 6.00 16.3
— —
(250 x 150) (273,0 x 168,3) (152,4) (7,4) (152,4) (7,4)
267,4mm x 216,3mm 10.52 x 8.52 6.00 17.40 — — — —
(250 x 200) (267,4 x 216,3) (152,4) (7,89)
10 x 8 10.75 x 8.63 6.00 18.3 6.00 18.3
— —
(250 x 200) (273,0 x 219,1) (152,4) (8,3) (152,4) (8,3)
FIGURE 550a
CAST CONCENTRIC 12 x 4 12.75 x 4.50 7.00 22.7 7.00 22.7
REDUCER — —
(300 x 100) (323,9 x 114,3) (177,8) (10,3) (177,8) (10,3)
12 x 6 12.75 x 6.63 7.00 23.6 7.00 24.2
— —
(300 x 150) (323,9 x 168,3) (177,8) (10,7) (177,8) (11,0)
318,5mm x 216,3mm 12.54 x 8.52 7.00 23.12 — — — —
(300 x 200) (318,5 x 216,3) (177,8) (10,48)
12 x 8 12.75 x 8.63 7.00 25.2 7.00 25.8
— —
(300 x 200) (323,9 x 219,1) (177,8) (11,4) (177,8) (11,7)
318,5mm x 267,4mm 12.54 x 10.52 7.00 25.42 — — — —
(300 x 250) (318,5 x 267,4) (177,8) (11,53)
12 x 10 12.75 x 10.75 7.00 28.2 7.00 28.2 7.00 28.2
(300 x 250) (323,9 x 273,0) (177,8) (12,8) (177,8) (12,8) (177,8) (12,8)
NOTES
a. Figure 550 is available for the Americas market only.
FIGURE 1 (3 OF 3)
FIGURES 250, 350, AND 550 CONCENTRIC REDUCERS
NOMINAL DIMENSIONS
 TFP1815
Page 5 of 26

Figure 501 Figure 510

Nominal Pipe Size Cast 45° Elbow Cast 90° Elbow

Nominal Approx. Nominal Approx.

ANSI O.D. C to E Weight C to E Weight
Inches Inches Inches Lbs. Inches Lbs.
(DN) (mm) (mm) (kg) (mm) (kg)
1 1.0 1.7 0.6 2.25 0.8
(25) (33,7) (43,2) (0,3) (57,2) (0,4)
1-1/4 1.7 1.8 0.8 2.8 1.1
(32) (42,4) (44,5) (0,4) (69,9) (0,5)
1-1/2 1.9 1.8 1.0 2.8 1.4
(40) (48,3) (44,5) (0,5) (69,9) (0,6)
C to E
2 2.4 2.0 1.3 3.3 2.0
(50) (60,3) (50,8) (0,6) (82,6) (0,9)
2-1/2 2.9 2.3 2.1 3.8 2.8
(65) (73,0) (57,2) (1,0) (95,3) (1,3) FIGURE 501
CAST 45° ELBOW
76,1mm 3.0 2.3 2.2 3.8 3.0
(65) (76,1) (57,2) (1,0) (95,3) (1,3)
3 3.5 2.5 3.4 4.3 4.1
(80) (88,9) (63,5) (1,5) (108,0) (1,9)
4 4.5 3.0 5.5 5.0 7.0
(100) (114,3) (76,2) (2,5) (127,0) (3,2)
139,7mm 5.5 3.3 7.2 5.5 10.3 C to E
(125) (139,7) (82,6) (3,3) (139,7) (4,7)
FIGURE 510
165,1mm 6.5 3.5 9.2 6.5 13.9 CAST 90° ELBOW
(150) (165,1) (88,9) (4,2) (165,1) (6,3)
6 6.6 3.5 11.2 6.5 15.2
(150) (168,3) (88,9) (5,1) (165,1) (6,9)
8 8.6 4.25 20.6 7.8 29.6
(200) (219,1) (108,0) (9,3) (196,9) (13,4)
267,4mm 10.52 9.00 45.69
— —
(250) (267,4) (228,6) (20,72)
10 10.750 4.75 30.1 9.00 52.0
(250) (273,0) (120,7) (13,7) (228,6) (23,6)
318,5mm 12.54 10.00 61.86
— —
(300) (318,5) (254,0) (21,86)
12 12.750 5.25 48.0 10.00 66.4
(300) (323,9) (133,4) (22,0) (254,0) (30,1)

FIGURE 2
FIGURES 501 AND 510 ELBOWS
NOMINAL DIMENSIONS
TFP1815
Page 6 of 26

Figure 519 Figure 260 (a)

Nominal Pipe Size Cast Tee Cast End Cap

Nominal Approx. Nominal Approx.

ANSI O.D. C to E Weight E to E Weight
Inches Inches Inches Lbs. Inches Lbs.
(DN) (mm) (mm) (kg) (mm) (kg)
1 1.3 2.25 1.1 0.8 0.2
(25) (33,4) (57,2) (0,5) (21,1) (0,1)
1-1/4 1.7 2.8 1.7 0.8 0.3
(32) (42,4) (69,9) (0,8) (21,1) (0,1)
C to E 1-1/2 1.9 2.8 2.1 0.8 0.4
(40) (48,3) (69,9) (1,00) (21,1) (0,2)
2 2.4 3.3 2.8 0.9 0.7
(50) (60,3) (82,6) (1,3) (23,4) (0,3)
2-1/2 2.9 3.8 4.4 0.9 1.0
C to E (65) (73,0) (95,3) (2,0) (23,4) (0,5)

FIGURE 519 76,1mm 3.0 3.8 4.5 0.9 1.3

CAST TEE (65) (76,1) (95,3) (2,0) (21,8) (0,6)
3 3.5 4.3 6.5 0.9 1.4
E to E (80) (88,9) (108,0) (3,0) (23,4) (0,6)
4 4.5 5.0 9.5 1.0 2.6
(100) (114,3) (127,0) (4,3) (25,4) (1,2)
139,7mm 5.5 5.5 13.9 0.9 4.7
(125) (139,7) (139,7) (6,3) (23,4) (2,1)

FIGURE 260a 5 5.6 5.0 14.2 1.0 5.0

CAST END CAP (125) (141,3) (127,0) (6,4) (25,4) (2,3)
165,1mm 6.5 6.5 19.7 0.9 6.4
(150) (165,1) (165,1) (8,9) (23,4) (2,9)
6 6.6 6.5 22.4 1.0 6.2
(150) (168,3) (165,1) (10,2) (25,4) (2,8)
216,3mm 8.52 1.06 11.02
— —
(200) (216,3) (27,0) (4,99)
8 8.6 7.8 39.8 1.1 7.1
(200) (219,1) (196,9) (18,1) (27,0) (3,2)
267,4mm 10.52 9.00 62.58 1.02 19.05
(250) (267,4) (228,6) (28,39) (25,78) (8,64)
10 10.8 9.00 64.2 1.0 24.5
(250) (273,0) (228,6) (29,1) (25,8) (11,1)
318,5mm 12.54 10.00 82.79 1.02 28.82
(300) (318,5) (254,0) (37,55) (25,8) (13,07)
12 12.8 10.00 110.0 1.02 31.0
(300) (323,9) (254,0) (49,9) (25,8) (14,1)
NOTES
a. Available with tapped plugs. Contact Johnson Controls.

FIGURE 3
FIGURES 519 TEE AND FIGURE 260 END CAP
NOMINAL DIMENSIONS
 TFP1815
Page 7 of 26

Figure 510S Figure 519S

Nominal Pipe Size 90° Elbow Tee

Nominal Approx. Nominal Approx.

ANSI O.D. C to E Weight C to E Weight
Inches Inches Inches Lbs. Inches Lbs.
(DN) (mm) (mm) (kg) (mm) (kg)
2 2.4 2.8 1.5 2.8 2.6
(50) (60,3) (69,9) (0,7) (69,9) (1,2)
2-1/2 2.9 3.0 2.1 3.0 4.4 C to E
(65) (73,0) (76,2) (1,0) (76,2) (2,0)
FIGURE 510S
76,1mm 3.0 3.0 2.3 3.0 3.1 90° ELBOW
(65) (76,1) (76,2) (1,0) (76,2) (1,4) SHORT PATTERN
3 3.5 3.4 3.0 3.8 6.5
(80) (88,9) (85,9) (1,4) (85,9) (3,0) C to E
4 4.5 4.0 5.0 4.0 10.7
(100) (114,3) (101,6) (2,3) (101,6) (4,9)
139,7mm 5.5 4.9 8.7 4.9 10.9
(125) (139,7) (124,0) (3,9) (124,0) (5,0)
5 5.6 4.8 9.4 4.8 11.6 C to E
(125) (141,3) (123,0) (4,3) (123,0) (5,3) FIGURE 519S
165,1mm 6.5 5.5 11.4 5.5 14.8 TEE
(150) (165,1) (139,7) (5,2) (139,7) (6,7) SHORT PATTERN

6 6.6 5.5 12.1 5.5 15.0

(150) (168,3) (139,7) (5,5) (139,7) (6,8)
8 8.6 6.9 22.2 6.9 39.8
(200) (219,1) (174,8) (10,1) (174,8) (18,1)

FIGURE 4
FIGURES 510S ELBOW AND FIGURE 519S TEE
NOMINAL DIMENSIONS
TFP1815
Page 8 of 26

Figure 510DE(a)
Nominal Pipe Size 90° Drain Elbow

Nominal Nominal Nominal Approx.

ANSI O.D. C to E A B Weight
Inches Inches Inches Inches Inches Lbs.
(DN) (mm) (mm) (mm) (mm) (kg)
1" NPT 2 2.4 3.8 2.0 2.8 3.1
(50) (60,3) (95,3) (50,8) (69,9) (1,4)
2-1/2 2.9 3.8 2.0 2.8 2.2
B (65) (73,0) (95,3) (50,8) (69,9) (1,0)

A 3 3.5 4.3 2.3 2.8 6.0

(80) (88,9) (108,0) (59,4) (69,9) (2,7)
C to E
4 4.5 5.0 2.9 2.8 8.6
(100) (114,3) (127,0) (72,4) (69,9) (3,9)
6 6.6 6.5 3.9 2.8 18.0
(150) (168,3) (165,1) (99,6) (69,9) (8,2)
8 8.6 7.8 5.00 2.8 31.0
(200) (219,1) (196,9) (125,7) (69,9) (14,1)
NOTES
a. Figure 510DE not available for the EMEA market.

FIGURE 5
FIGURE 510DE 90° DRAIN ELBOW
NOMINAL DIMENSIONS

Nominal Pipe Dimensions- Inches

Size (mm) Approx.
Weight
ANSI Lbs.
A B
Inches Outlet C D (kg)
NPT(1) O.D. Takeout
(DN)

1.3 1.8 1.9 0.8

1/2 (31,8) (44,5) (48,0) (0,4)
1-1/2 1.9 1.3 1.8 1.9 0.8
D NPT 3/4
C (40) (48,3) (31,8) (44,5) (48,0) (0,4)
1.4 2.0 2.0 0.9
1 (34,8) (50,8) (51,3) (0,4)
B 1.3 1.8 1.9 0.9
1/2
A (31,8) (44,5) (48,0) (0,4)
2 2.4 1.3 1.8 1.9 0.8
3/4
(50) (60,3) (31,8) (44,5) (48,0) (0,4)
1.4 2.0 2.0 1.1
1 (34,8) (50,8) (51,3) (0,5)
1.5 2.0 1.9 1.8
1/2 (37,3) (50,0) (48,0) (0,8)
2-1/2 2.9 1.5 2.0 1.9 1.1
3/4
(65) (73,0) (37,3) (50,0) (48,0) (0,5)
1.4 2.0 2.0 1.1
1 (34,8) (50,8) (51,3) (0,5)
NOTES
a. ISO threaded outlets are available upon request.
b. ADACAP not available for the EMEA market.
c. Rated pressure 300 psi (20,7 bar).

FIGURE 6
ADACAP
NOMINAL DIMENSIONS
 TFP1815
Page 9 of 26

Figure 320
Nominal Pipe Size Fabricated Thread Tee

Nominal Nominal Approx.

ANSI O.D. C to GE C to TE Weight
Inches Inches Inches Inches Lbs.
(DN) (mm) (mm) (mm) (kg)
1 1.31 2.25 2.25 1.3
(25) (33,4) (57,2) (57,2) (0,6)
1-1/4 1.66 2.75 2.75 1.5
(32) (42,4) (69,9) (69,9) (0,7)
1-1/2 1.90 2.75 2.75 1.9
(40) (48,3) (69,9) (69,9) (0,9)
2 2.37 3.25 4.25 3.2
(50) (60,3) (82,6) (108,0) (1,5)
2-1/2 2.87 3.75 3.75 4.0
(65) (73,0) (95,3) (95,3) (1,8) C to TE
76,1mm 3.00 3.75 3.75 4.5
(65) (76,1) (95,3) (95,3) (2,0)
3 3.50 4.25 6.00 6.0
(80) (88,9) (108,0) (152,4) (2,7)
4 4.50 5.00 7.25 11.0 C to GE
(100) (114,3) (127,0) (184,2) (5,0)
139,7mm 5.50 5.50 5.50 21.0
(125) (139,7) (139,7) (139,7) (9,5)
5 5.56 5.50 5.50 23.0
(125) (141,3) (139,7) (139,7) (10,5)
165,1mm 6.50 6.50 6.50 25
(150) (165,1) (165,1) (165,1) (11,3)
6 6.63 6.50 6.50 28.0
(150) (168,3) (165,1) (165,1) (12,7)
8 8.63 7.75 7.75 38.7
(200) (219,1) (196,9) (196,9) (17,6)
10 10.75 9.00 9.00 72.1
(250) (273,0) (228,6) (228,6) (32,8)
12 12.75 10.00 10.00 92.5
(300) (323,9) (254,0) (254,0) (42,0)
NOTES
a. Figure 320 not available for the EMEA market.

FIGURE 7
FIGURE 320 FABRICATED GROOVE X GROOVE X MALE THREAD TEES (SEGMENT WELDED)
NOMINAL DIMENSIONS
TFP1815
Page 10 of 26

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee
Nominal Approx. Nominal Approx.
O.D.
ANSI Inches C to E Weight C to E Weight
Inches
(DN) Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg)
1-1/4 x 1-1/4 x 1 1.66 x 1.66 x 1.31 2.75 1.3
— —
(32 x 32 x 25) (42,4 x 42,4 x 33,4) (69,9) (0,6)
1-1/2 x 1-1/2 x 1 1.90 x 1.90 x 1.31 2.75 1.4
— —
(40 x 40 x 25) (48,3 x 48,3 x 33,4) (69,9) (0,6)
1-1/2 x 1-1/2 x 1-1/4 1.90 x 1.90 x 1.66 2.75 1.5
— —
(40 x 40 x 32) (48,3 x 48,3 x 42,4) (69,9) (0,7)
2x2x1 2.37 x 2.37 x 1.32 3.25 1.6
— —
(50 x 50 x 25) (60,3 x 60,3 x 33,4) (82,6) (0,7)
2 x 2 x 1-1/2 2.37 x 2.37 x 1.90 3.25 2.7 3.25 2.0
(50 x 50 x 40) (60,3 x 60,3 x 48,3) (82,6) (1,2) (82,6) (0,9)
2-1/2 x 2-1/2 x 1 2.87 x 2.87 x 1.32 3.75 2.3
— —
(65 x 65 x 25) (73,0 x 73,0 x 33,4) (95,3) (1,1)
C to E 2-1/2 x 2-1/2 x 1-1/4 2.87 x 2.87 x 1.66 3.75 4.2
— —
(65 x 65 x 32) (73,0 x 73,0 x 42,4) (95,3) (1,9)
2-1/2 x 2-1/2 x 1-1/2 2.87 x 2.87 x 1.90 3.75 4.2
— —
(65 x 65 x 40) (73,0 x 73,0 x 48,3) (95,3) (1,9)
2-1/2 x 2-1/2 x 2 2.87 x 2.87 x 2.37 3.75 4.2 3.75 4.5
C to E (65 x 65 x 50) (73,0 x 73,0 x 60,3) (95,3) (1,9) (95,3) (2,0)

FIGURE 221 76,1mm x 76,1mm x 1 3.00 x 3.00 x 1.32 3.75 2.4

— —
CAST TEE REDUCING (65 x 65 x 25) (76,1 x 76,1 x 33,4) (95,3) (1,1)
GROOVED
(SEGMENT WELDED) 76,1mm x 76,1mm x 1-1/4 3.00 x 3.00 x 1.66 3.75 4.3
— —
(65 x 65 x 32) (76,1 x 76,1 x 42,4) (95,3) (2,0)
C to E 76,1mm x 76,1mm x 1-1/2 3.00 x 3.00 x 1.90 3.75 4.5 3.75 4.2
(65 x 65 x 40) (76,1 x 76,1 x 48,3) (95,3) (2,0) (95,3) (1,9)
76,1mm x 76,1mm x 2 3.00 x 3.00 x 2.37 3.75 4.3 3.75 4.6
(65 x 65 x 50) (76,1 x 76,1 x 60,3) (95,3) (2,0) (95,3) (2,1)
3x3x1 3.50 x 3.50 x 1.32 4.25 5.6 4.25 6.0
C to E (80 x 80 x 25 (88,9 x 88,9 x 33,4) (108,0) (2,5) (108,0) (2,7)

FIGURE 321 3 x 3 x 1-1/4 3.50 x 3.50 x 1.66 4.25 6.1

— —
FABRICATED TEE REDUCING (80 x 80 x 32) (88,9 x 88,9 x 42,4) (108,0) (2,8)
GROOVED 3 x 3 x 1-1/2 3.50 x 3.50 x 1.90 4.25 5.9 4.25 6.2
(SEGMENT WELDED) (80 x 80 x 40) (88,9 x 88,9 x 48,3) (108,0) (2,7) (108,0) (2,8)
3x3x2 3.50 x 3.50 x 2.37 4.25 6.0 4.25 6.4
(80 x 80 x 50) (88,9 x 88,9 x 60,3) (108,0) (2,7) (108,0) (2,9)
3 x 3 x 2-1/2 3.50 x 3.50 x 2.87 4.25 6.2 4.25 6.5
(80 x 80 x 65) (88,9 x 88,9 x 73,0) (108,0) (2,8) (108,0) (2,9)
3 x 3 x 76,1mm 3.50 x 3.50 x 3.00 4.25 6.0 4.25 6.7
(80 x 80 x 65) (88,9 x 88,9 x 76,1) (108,0) (2,7) (108,0) (3,0)
4x4x1 4.50 x 4.50 x 1.32 5.00 8.0
— —
(100 x 100 x 25) (114,3 x 114,3 x 33,4) (127,0) (3,7)
4 x 4 x 1-1/4 4.50 x 4.50 x 1.66 5.00 9.8
— —
(100 x 100 x 32) (114,3 x 114,3 x 42,4) (127,0) (4,4)
4 x 4 x 1-1/2 4.50 x 4.50 x 1.90 5.00 9.9
— —
(100 x 100 x 40) (114,3 x 114,3 x 48,3) (127,0) (4,5)
4x4x2 4.50 x 4.50 x 2.37 5.00 9.1 5.00 11.0
(100 x 100 x 50) (114,3 x 114,3 x 60,3) (127,0) (4,1) (127,0) (5,0)
4 x 4 x 2-1/2 4.50 x 4.50 x 2.88 5.00 9.5 5.00 11.2
(100 x 100 x 65) (114,3 x 114,3 x 73,0) (127,0) (4,3) (127,0) (5,1)
4 x 4 x 76,1mm 4.50 x 4.50 x 3.00 5.00 9.5 5.00 11.4
(125 x 125 x 65) (114,3 x 114,3 x 76,1) (127,0) (4,3) (127,0 (5,2)

FIGURE 8 (1 OF 3)
FIGURES 221 AND 321 REDUCING TEES
NOMINAL DIMENSIONS
 TFP1815
Page 11 of 26

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee
Nominal Approx. Nominal Approx.
O.D.
ANSI Inches C to E Weight C to E Weight
Inches
(DN) Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg)
4x4x3 4.50 x 4.50 x 3.50 5.00 9.7 5.00 11.6
(100 x 100 x 80) (114,3 x 114,3 x 88,9) (127,0) (4,4) (127,0 (5,3)
139,7mm x 139,7mm x 3 5.50 x 5.50 x 3.50 5.50 12.7 5.50 12.2
(125 x 125 x 80) (139,7 x 139,7 x 88,9) (139,7) (5,8) (139,7) (5,5)
139,7mm x 139,7mm x 4 5.50 x 5.50 x 4.50 5.50 13.4 5.50 12.5
(125 x 125 x 100) (139,7 x 139,7 x 114,3) (139,7) (6,1) (139,7) (5,7)
5x5x1 5.56 x 5.56 x 1.31 5.50 13.0
— —
(125 x 125 x 25) (141,3 x 141,3 x 33,4) (139,7) (5,9)
5 x 5 x 1-1/2 5.56 x 5.56 x 1.90 5.50 13.4
— —
(125 x 125 x 40) (141,3 x 141,3 x 48,3) (139,7) (6,1)
5x5x2 5.56 x 5.56 x 2.37 5.50 14.1
— —
(125 x 125 x 50) (141,3 x 141,3 x 60,3) (139,7) (6,4)
5 x 5 x 2-1/2 5.56 x 5.56 x 2.87 5.50 18.0 5.50 14.8 C to E
(125 x 125 x 65) (141,3 x 141,3 x 73,0) (139,7) (8,2) (139,7) (6,7)
5 x 5 x 76,1mm 5.56 x 5.56 x 3.00 5.50 15.3
— —
(125 x 125 x 65) (141,3 x 141,3 x 76,1) (139,7) (6,9)
5x5x3 5.56 x 5.56 x 3.50 5.50 14.0 5.50 16.0
(125 x 125 x 80) (141,3 x 141,3 x 88,9) (139,7) (6,4) (139,7) (7,3) C to E
5x5x4 5.56 x 5.56 x 4.50 5.50 13.9 5.50 16.4 FIGURE 221
(125 x 125 x 100) (141,3 x 141,3 x 114,3) (139,7) (6,3) (139,7) (7,4) CAST TEE REDUCING
GROOVED
165,1mm x 165,1mm x 3 6.50 x 6.50 x 3.50 6.50 18.0 6.50 22.0 (SEGMENT WELDED)
(150 x 150 x 80) (165,1 x 165,1 x 88,9) (165,1) 8,2 (165,1) (10,0)
165,1mm x 165,1mm x 4 6.50 x 6.50 x 4.50 6.50 19.5 6.50 22.6 C to E
(150 x 150 x 100) (165,1 x 165,1 x 114,3) (165,1) 8,9 (165,1) (10,3)
165,1mm x 165,1mm x 5 6.50 x 6.50 x 5.50 6.50 23.2
— —
(150 x 150 x 125) (165,1 x 165,1 x 139,7) (165,1) (10,5)
165,1mm x 165,1mm x 139,7mm 6.50 x 6.50 x 5.50 6.50 22.9
— —
(150 x 150 x 125) (165,1 x 165,1 x 141,3) (165,1) (10,4) C to E
6x6x1 6.63 x 6.63 x 1.31 6.50 22.8 FIGURE 321
— —
(150 x 150 x 25) (168,3 x 168,3 x 33,4) (165,1) (10,3) FABRICATED TEE REDUCING
6 x 6 x 1-1/2 6.63 x 6.63 x 1.90 6.50 22.9 GROOVED
— — (SEGMENT WELDED)
(150 x 150 x 40) (168,3 x 168,3 x 48,3) (165,1) (10,4)
6x6x2 6.63 x 6.63 x 2.37 6.50 19.4 6.50 23.0
(150 x 150 x 50) (168,3 x 168,3 x 60,3) (165,1) (8,8) (165,1) (10,4)
6 x 6 x 2-1/2 6.63 x 6.63 x 2.87 6.50 21.2 6.50 23.4
(150 x 150 x 65) (168,3 x 168,3 x 73,0) (165,1) (9,8) (165,1) (10,6)
6 x 6 x 76,1mm 6.63 x 6.63 x 3.00 6.50 21.2 6.50 23.5
(150 x 150 x 65) (168,3 x 168,3 x 76,1) (165,1) 9,8 (165,1) (10,7)
6x6x3 6.63 x 6.63 x 3.50 6.50 21.0 6.50 23.7
(150 x 150 x 80) (168,3 x 168,3 x 88,9) (165,1) (9,5) (165,1) (10,7)
6x6x4 6.63 x 6.63 x 4.50 6.50 21.8 6.50 23.9
(150 x 150 x 100) (168,3 x 168,3 x 114,3) (165,1) (9,9) (165,1) (10,8)
6 x 6 x 139,7mm 6.63 x 6.63 x 5.50 6.50 23.0 6.50 24.0
(150 x 150 x 125) (168,3 x 168,3 x 139,7) (165,1) 10,4 (165,1) (10,9)
6x6x5 6.63 x 6.63 x 5.56 6.50 27.0
— —
(150 x 150 x 125) (168,3 x 168,3 x 141,3) (165,1) 12,2
8 x 8 x 1-1/2 8.63 x 8.63 x 1.90 7.75 36.0
— —
(200 x 200 x 40) (219,1 x 219,1 x 48,3) (196,9 (16,3)
8x8x2 8.63 x 8.63 x 2.375 7.75 36.2
— —
(200 x 200 x 50) (219,1 x 219,1 x 60,3) (196,9) (16,4)

FIGURE 8 (2 OF 3)
FIGURES 221 AND 321 REDUCING TEES
NOMINAL DIMENSIONS
TFP1815
Page 12 of 26

Figure 221 Figure 321

Nominal Pipe Size Cast Fabricated
Reducing Tee Reducing Tee
Nominal Approx. Nominal Approx.
O.D.
ANSI Inches C to E Weight C to E Weight
Inches
(DN) Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg)
8 x 8 x 2-1/2 8.63 x 8.63 x 2.88 7.75 36.4
— —
(200 x 200 x 65) (219,1 x 219,1 x 73,0) (196,9) (16,5)
216mm x 216mm x 165,1mm 8.52 x 8.52 x 6.50 7.75 37.9
— —
(200 x 200 x 150) (216,3 x 216,3 x 165,1) (196,9) (17,2)
8 x 8 x 76,1mm 8.63 x 8.63 x 3.00 7.75 36.4
— —
(200 x 200 x 65) (216,1 x 219,1 x 76.1) (196,9) (16,5)
8x8x3 8.63 x 8.63 x 3.50 7.75 36.5
— —
(200 x 200 x 80) (219,1 x 219,1 x 88,9) (196,9) (16,6)
8x8x4 8.63 x 8.63 x 4.50 7.75 37.2 7.75 36.4
(200 x 200 x 100) (219,1 x 219,1 x 114,1) (196,9) (16,9) (196,9) (16,5)
8 x 8 x 139,7mm 8.63 x 8.63 x 5.56 7.75 37.7 7.75 36.7
C to E (200 x 200 x 125) (219,1 x 219,1 x 139,7) (196,9) (17,1) (196,9) (16,6)
8x8x5 8.63 x 8.63 x 5.50 7.75 36.8
— —
(200 x 200 x 125) (219,1 x 219,1 x 141,3) (196,9) (16,7)
8 x 8 x 165,1mm 8.63 x 8.63 x 6.50 7.75 37.7 7.75 39.0
(200 x 200 x 150) (219,1 x 219,1 x 165,1) (196,9) (17,1) (196,9) (17,7)
C to E 10 x 10 x 1-1/2 10.75 x 10.75 x 1.90 9.00 57.0
— —
(250 x 250 x 40) (273,0 x 273,0 x 48,3) (228,6) (25,8)
FIGURE 221
CAST TEE REDUCING 10 x 10 x 2 10.75 x 10.75 x 2.37 9.00 57.1
GROOVED — —
(250 x 250 x 50) (273,0 x 273,0 x 60,3) (228,6) (25,9)
(SEGMENT WELDED)
10 x 10 x 2-1/2 10.75 x 10.75 x 2.87 9.00 57.3
— —
C to E (250 x 250 x 65) (273,0 x 273,0 x 73,0) (228,6) (26,0)
10 x 10 x 3 10.75 x 10.75 x 3.50 9.00 57.4
— —
(250 x 250 x 80) (273,0 x 273,0 x 88,9) (228,6) (26,0)
10 x 10 x 4 10.75 x 10.75 x 4.50 9.00 57.8
— —
(250 x 250 x 100) (273,0 x 273,0 x 114,3) (228,6) (26,2)
C to E 10 x 10 x 5 10.75 x 10.75 x 5.56 9.00 58.0
— —
(250 x 250 x 125) (273,0 x 273,0 x 141,3) (228,6) (26,3)
FIGURE 321
FABRICATED TEE REDUCING 10 x 10 x 6 10.75 x 10.75 x 6.63 9.00 62.0
GROOVED — —
(250 x 250 x 150) (273,0 x 273,0 x 168,3) (228,6) (28,1)
(SEGMENT WELDED)
10 x 10 x 8 10.75 x 10.75 x 8.63 9.00 63.0
— —
(250 x 250 x 200) (273,0 x 273,0 x 219,1) (228,6) (28,6)
12 x 12 x 1 12.75 x 12.75 x 1.31 10.00 64.0
— —
(300 x 300 x 25) (323,9 x 323,9 x 33,4) (254,0) (29,0)
12 x 12 x 2 12.75 x 12.75 x 2.37 10.00 69.5
— —
(300 x 300 x 50) (323,9 x 323,9 x 60,3) (254,0) (31,5)
12 x 12 x 2-1/2 12.75 x 12.75 x 2.87 10.00 75.6
— —
(300 x 300 x 65) (323,9 x 323,9 x 73,0) (254,0) (34,3)
12 x 12 x 3 12.75 x 12.75 x 3.50 10.00 80.2
— —
(300 x 300 x 80) (323,9 x 323,9 x 88,9) (254,0) (36,4)
12 x 12 x 4 12.75 x 12.75 x 4.50 10.00 80.5
— —
(300 x 300 x 100) (323,9 x 323,9 x 114,3) (254,0) (36,5)
12 x 12 x 5 12.75 x 12.75 x 5.56 10.00 80.7
— —
(300 x 300 x 125) (323,9 x 323,9 x 141,3) (254,0) (36,6)
12 x 12 x 6 12.75 x 12.75 x 6.63 10.00 80.9
— —
(300 x 300 x 150) (323,9 x 323,9 x 168,3) (254,0) (36,7)
12 x 12 x 165,1mm 12.75 x 12.75 x 6.50 10.00 79.9
— —
(300 x 300 x 150) (323,9 x 323,9 x 165,1) (254,0) (36,2)
12 x 12 x 8 12.75 x 12.75 x 8.63 10.00 76.3
— —
(300 x 300 x 200) (323,9 x 323,9 x 219,1) (254,0) (34,6)
12 x 12 x 10 12.75 x 12.75 x 10.75 10.00 77.6
— —
(300 x 300 x 250) (323,9 x 323,9 x 273,0) (254,0) (35,2)
FIGURE 8 (3 OF 3)
FIGURES 221 AND 321 REDUCING TEES
NOMINAL DIMENSIONS
 TFP1815
Page 13 of 26

Nominal Pipe Figure 327(a) Figure 341(a) Figure 342(a)

Size

Nominal Approx. Nominal Mating Approx. Nominal Mating Approx.

ANSI O.D. C to E Weight E to E Flange Weight E to E Flange Weight
Inches Inches Inches Lbs. Inches Bolt Lbs. Inches Bolt Lbs.
(DN) (mm) (mm) (kg) (mm) Qty. (kg) (mm) Qty. (kg)
1 1.31 2.25 2.2 3.00 2.3 3.00 4.0
4 4 C to E
(25) (33,4) (57,2) (1,0) (76,2) (1,0) (76,2) (1,8)
1-1/4 1.66 2.75 2.2 4.00 2.8 4.00 4.6
4 4
(32) (42,4) (69,9) (1,0) (101,6) (1,3) (101,6) (2,1)
1-1/2 1.90 2.75 2.5 4.00 3.2 4.00 7.1
4 4
(40) (48,3) (69,9) (1,1) (101,6) (1,5) (101,6) (3,2)
C to E
2 2.37 3.25 3.7 4.00 5.2 4.00 8.2
4 8
(50) (60,3) (82,6)b (1,7)b (101,6) (2,4) (101,6) (3,7) FIGURE 327a
2-1/2 2.87 3.75 5.8 4.00 8.0 4.00 11.9 FABRICATED CROSS
(65) (73,0) (95,3)b (2,6)b (101,6) 4 (3,6) (101,6) 8 (5,4) GROOVED
(SEGMENT WELDED)
76,1mm 3.00 3.75 6.0 4.00 8.8 4.00 12.5
(65) (76,1) 4 8 E to E
(95,3) (2,7) (101,6) (4,0) (101,6) (5,7)
3 3.50 4.25 8.6 4.00 4 10.2 4.00 15.5
8
(80) (88,9) (108,0) (3,9) (101,6) (4,6) (101,6) (7,0)
4 4.50 5.00 20.7 6.00 17.2 6.00 28.0
8 8
(100) (114,3) (127,0)b (9,4)b (152,4) (7,8) (152,4) (12,7)
139,7mm 5.50 5.50 18.3 6.00 18.5 6.00 32.5
8 8
(125) (139,7) (139,7) (8,3) (152,4) (8,4) (152,4) (14,7)
FIGURE 341a
5 5.56 5.50 18.5 6.00 21.4 6.00 37.0 FABRICATED
8 8
(125) (141,3) (139,7) (8,4) (152,4) (9,7) (152,4) (16,8) FLANGE ADAPTER
165,1mm 6.50 6.50 26.2 6.00 22.0 6.00 42.5 ANSI CLASS 150 LBS.
8 12 GROOVED
(150) (165,1) (165,1) (11,9) (152,4) (10,0) (152,4) (19,3)
6 6.63 6.50 27.3 6.00 26.0 6.00 48.0 FIGURE 342a
8 12 FABRICATED
(150) (168,3) (165,1) (12,4) (152,4) (11,8) (152,4) (21,8)
FLANGE ADAPTER
216,3mm 8.52 7.75 44.0 6.00 34.5 6.00 72.5 ANSI CLASS 300 LBS.
8 12
(200) (216,3) (196,9) (20,0) (152,4) (15,6) (152,4) (32,9) GROOVED
8 8.63 7.75 48.0 6.00 38.4 6.00 79.0
8 12
(200) (219,1) (196,9) (21,7) (152,4) (17,4) (152,4) (35,8)
10 10.75 9.00 75.0 8.00 12 65.0 8.00 122.0
16
(250) (273,0) (228,6) (34,0) (203,2) (29,5) (203,2) (55,3)
12 12.75 10.00 95.8 8.00 91.0 8.00 183.0
12 16
(300) (323,9) (254,0) (43,4) (203,2) (41,3) (203,2) (83,0)
NOTES
a. Figure 327, Figure 341, and Figure 342 are not available for the EMEA market.
b. Figure 227
FIGURE 9
FIGURE 327 CROSS AND FIGURE 341 AND FIGURE 342 FLANGE ADAPTERS
NOMINAL DIMENSIONS
TFP1815
Page 14 of 26

Nominal Pipe Size

Nominal Approx.
C to E Weight
O.D. Inches Lbs.
ANSI Inches (mm) (kg)
Inches
(DN) (mm)

2 x 2 x 3/4 2.37 x 2.37 x 1.05 3.25 2.0

(50 x 50 x 20) (60,3 x 60,3 x 26,7) (82,6) (0,9)
2x2x1 2.37 x 2.37 x 1.31 3.25 2.2
(50 x 50 x 25) (60,3 x 60,3 x 33,4) (82,6) (1,0)
2 x 2 x 1-1/4 2.37 x 2.37 x 1.66 3.25 2.3
(50 x 50 x 32) (60,3 x 60,3 x 42,4) (82,6) (1,0)
2 x 2 x 1-1/2 2.37 x 2.37 x 1.90 3.25 1.4
(50 x 50 x 40) (60,3 x 60,3 x 48,3) (82,6) (1,1)
2-1/2 x 2-1/2 x 1 2.875 x 2.875 x 1.315 3.75 3.6
(65 x 65 x 25) (73,0 x 73,0 x 33,4) (95,3) (1,6)
2-1/2 x 2-1/2 x 1-1/4 2.875 x 2.875 x 1.660 3.75 3.8
(65 x 65 x 32) (73,0 x 73,0 x 42,4) (95,3) (1,7)
2-1/2 x 2-1/2 x 1-1/2 2.875 x 2.875 x 1.900 3.75 4.0
(65 x 65 x 40) (73,0 x 73,0 x 48,3) (95,3) (1,8)
2-1/2 x 2-1/2 x 2 2.875 x 2.875 x 2.375 3.75 4.2
(65 x 65 x 50) (73,0 x 73,0 x 60,3) (95,3) (1,9)
76,1mm x 76,1mm x 1 3.00 x 3.00 x 1.31 3.75 3.8
(65 x 65 x 25) (76,1 x 76,1 x 33,4) (95,3) (1,7)
C to E 76,1mm x 76,1mm x 1-1/4 3.00 x 3.00 x 1.66 3.75 4.0
(65 x 65 x 32) (76,1 x 76,1 x 42,4) (95,3) (1,8)
76,1mm x 76,1mm x 1-1/2 3.00 x 3.00 x 1.90 3.75 4.2
(65 x 65 x 40) (76,1 x 76,1 x 48,3) (95,3) (1,9)
3 x 3 x 3/4 3.50 x 3.50 x 1.05 4.25 5.2
C to E (80 x 80 x 20) (88,9 x 88,9 x 26,7) (108,0) (2,4)
3x3x1 3.50 x 3.50 x 1.31 4.25 5.7
(80 x 80 x 25) (88,9 x 88,9 x 33,4) (108,0) (2,6)
3 x 3 x 1-1/2 3.50 x 3.50 x 1.90 4.25 5.8
(80 x 80 x 40) (88,9 x 88,9 x 48,3) (108,0) (2,6)
3x3x2 3.50 x 3.50 x 2.37 4.25 5.9
(80 x 80 x 50) (88,9 x 88,9 x 60,3) (108,0) (2,7)
3 x 3 x 2-1/2 3.50 x 3.50 x 2.87 4.25 6.3
(80 x 80 x 65) (88,9 x 88,9 x 73,0) (108,0) (2,9)
3 x 3 x 76,1mm 3.50 x 3.50 x 3.00 4.25 6.5
(80 x 80 x 65) (88,9 x 88,9 x 76,1) (108,0) (2,9)
4 x 4 x 3/4 4.50 x 4.50 x 1.05 3.75 6.4
(100 x 100 x 20) (114,3 x 114,3 x 26,7) (95,3) (2,9)
4x4x1 4.50 x 4.50 x 1.31 5.00 6.9
(100 x 100 x 25) (114,3 x 114,3 x 33,4) (127,0) (3,1)
4 x 4 x 1-1/4 4.50 x 4.50 x 1.66 5.00 7.6
(100 x 100 x 32) (114,3 x 114,3 x 42,4) (127,0) (3,4)
4 x 4 x 1-1/2 4.50 x 4.50 x 1.90 5.00 8.3
(100 x 100 x 40) (114,3 x 114,3 x 48,3) (127,0) (3,8)
4x4x2 4.50 x 4.50 x 2.37 5.00 9.6
(100 x 100 x 50) (114,3 x 114,3 x 60,3) (127,0) (4,4)
4 x 4 x 2-1/2 4.500 x 4.500 x 2.875 5.00 10.0
(100 x 100 x 65) (114,3 x 114,3 x 73,0) (127,0) (4,5)
4 x 4 x 76,1mm 4.500 x 4.500 x 3.00 5.00 10.5
(100 x 100 x 65) (114,3 x 114,3 x 76,1) (127,0) (4,8)
NOTES
a. Figure 323 not available for the EMEA market.

FIGURE 10 (1 OF 3)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES (SEGMENT WELDED)
NOMINAL DIMENSIONS
 TFP1815
Page 15 of 26

Nominal Pipe Size

Nominal Approx.
C to E Weight
O.D. Inches Lbs.
ANSI Inches (mm) (kg)
Inches
(DN) (mm)

4x4x3 4.50 x 4.50 x 3.50 5.00 10.3

(100 x 100 x 80) (114,3 x 114,3 x 88,9) (127,0) (4,7)
5x5x2 5.56 x 5.56 x 2.37 5.50 14.0
(125 x 125 x 50) (141,3 x 141,3 x 60,3) (139,7) (6,4)
5 x 5 x 2-1/2 5.56 x 5.56 x 2.87 5.50 14.3
(125 x 125 x 65) (141,3 x 141,3 x 73,0) (139,7) (6,5)
5 x 5 x 76,1mm 5.56 x 5.56 x 3.00 5.50 14.5
(125 x 125 x 65) (141,3 x 141,3 x 76,1) (139,7) (6,6)
5x5x3 5.56 x 5.56 x 3.50 5.50 14.6
(125 x 125 x 80) (141,3 x 141,3 x 88,9) (139,7) (6,6)
5x5x4 5.56 x 5.56 x 4.50 5.50 15.1
(125 x 125 x 100) (141,3 x 141,3 x 114,3) (139,7) (6,8)
165,1mm x 165,1mm x 2 6.50 x 6.50 x 2.37 6.50 9.5
(150 x 150 x 50) (165,1 x 165,1 x 60,3) (165,1) (4,3)
165,1mm x 165,1mm x 2-1/2 6.50 x 6.50 x 2.875 6.50 9.7
(150 x 150 x 65) (165,1 x 165,1 x 73,0) (165,1) (4,4)
165,1mm x 165,1mm x 6.50 x 6.50 x 3.00 6.50 9.7
76,1mm (165,1 x 165,1 x 76,1) (165,1) (4,4)
(150 x 150 x 65)
C to E
165,1mm x 165,1mm x 3 6.50 x 6.50 x 3.50 6.50 9.8
(150 x 150 x 80) (165,1 x 165,1 x 88,9) (165,1) (4,4)
165,1mm x 165,1mm x 4 6.50 x 6.50 x 4.50 6.50 10.0
(150 x 150 x 100) (165,1 x 165,1 x 114,3) (165,1) (4,5)
165,1mm x 165,1mm x 5 6.50 x 6.50 x 5.563 6.50 10.2
(150 x 150 x 125) (165,1 x 165,1 x 141,3) (165,1) (4,6) C to E
6 x 6 x 1-1/2 6.625 x 6.625 x 1.90 6.50 19.0
(150 x 150 x 40) (168,3 x 168,3 x 48,3) (165,1) (8,6)
6x6x2 6.625 x 6.625 x 2.375 6.50 21.3
(150 x 150 x 50) (168,3 x 168,3 x 60,3) (165,1) (9,7)
6 x 6 x 2-1/2 6.625 x 6.625 x 2.875 6.50 21.7
(150 x 150 x 65) (168,3 x 168,3 x 73,0) (165,1) (9,8)
6 x 6 x 76,1mm 6.625 x 6.625 x 3.00 6.50 14.5
(150 x 150 x 65) (168,3 x 168,3 x 76,1) (165,1) (6,6)
6x6x3 6.625 x 6.625 x 3.500 6.50 22.0
(150 x 150 x 80) (168,3 x 168,3 x 88,9) (165,1) (10,0)
6x6x4 6.625 x 6.625 x 4.500 6.50 22.5
(150 x 150 x 100) (168,3 x 168,3 x 114,3) (165,1) (10.2)
6x6x5 6.625 x 6.625 x 5.563 6.50 23.1
(150 x 150 x 125) (168,3 x 168,3 x 141,3) (165,1) 10,5
8x8x2 8.63 x 8.63 x 2.37 7.75 32.7
(200 x 200 x 50) (219,1 x 219,1 x 60,3) (196,9) (14,8)
8x8x3 8.63 x 8.63 x 3.50 7.75 33.5
(200 x 200 x 80) (219,1 x 219,1 x 88,9) (196,9) (15,2)
8x8x4 8.63 x 8.63 x 4.50 7.75 34.5
(200 x 200 x 100) (219,1 x 219,1 x 114,1) (196,9) (15,6)
8x8x5 8.63 x 8.63 x 5.56 7.75 34.7
(200 x 200 x 125) (219,1 x 219,1 x 141,3) (196,9) (15,7)
NOTES
a. Figure 323 not available for the EMEA market.

FIGURE 10 (2 OF 3)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES (SEGMENT WELDED)
NOMINAL DIMENSIONS
TFP1815
Page 16 of 26

Nominal Pipe Size

Nominal Approx.
C to E Weight
O.D. Inches Lbs.
ANSI Inches (mm) (kg)
Inches
(DN) (mm)

8 x 8 x 165,1mm 8.63 x 8.63 x 6.50 7.75 35.0

(200 x 200 x 150) (219,1 x 219,1 x 165,1) (196,9) (15,9)
8x8x6 8.63 x 8.63 x 6.63 7.75 35.6
(200 x 200 x 150) (219,1 x 219,1 x 168,3) (196,9) (16,1)
10 x 10 x 2 10.75 x 10.75 x 2.37 9.00 52.2
(250 x 250 x 50) (273,0 x 273,0 x 60,3) (228,6) (23,7)
10 x 10 x 3 10.75 x 10.75 x 3.50 9.00 53.0
(250 x 250 x 80) (273,0 x 273,0 x 88,9) (228,6) (24,0)
10 x 10 x 4 10.75 x 10.75 x 4.50 9.00 53.6
C to E (250 x 250 x 100) (273,0 x 273,0 x 114,3) (228,6) (24,3)
10 x 10 x 5 10.75 x 10.75 x 5.56 9.00 54.2
(250 x 250 x 125) (273,0 x 273,0 x 141,3) (228,6) (24,6)
10 x 10 x 165,1mm 10.75 x 10.75 x 6.50 9.00 55.5
(250 x 250 x 150) (273,0 x 273,0 x 165,1) (228,6) (25,2)
C to E 10 x 10 x 6 10.75 x 10.75 x 6.63 9.00 54.9
(250 x 250 x 150) (273,0 x 273,0 x 168,3) (228,6) (24,9)
10 x 10 x 8 10.75 x 10.75 x 8.63 9.00 55.3
(250 x 250 x 200) (273,0 x 273,0 x 219,1) (228,6) (25,1)
12 x 12 x 3 12.75 x 12.75 x 3.50 10.00 74.6
(300 x 300 x 80) (323,9 x 323,9 x 88,9) (254,0) (33,8)
12 x 12 x 4 12.75 x 12.75 x 4.50 10.00 75.1
(300 x 300 x 100) (323,9 x 323,9 x 141,3) (254,0) (34,1)
12 x 12 x 5 12.75 x 12.75 x 5.563 10.00 75.6
(300 x 300 x 125) (323,9 x 323,9 x 114,3) (254,0) (34,3)
12 x 12 x 165,1mm 12.75 x 12.75 x 6.50 10.00 76.2
(300 x 300 x 150) (323,9 x 323,9 x 165,1) (254,0) (34,6)
12 x 12 x 6 12.75 x 12.75 x 6.625 10.00 76.2
(300 x 300 x 150) (323,9 x 323,9 x 168,3) (254,0) (34,6)
12 x 12 x 8 12.750 x 12.750 x 8.625 10.00 76.3
(300 x 300 x 200) (323,9 x 323,9 x 219,1) (254,0) (34,6)
12 x 12 x 10 12.750 x 12.750 x 10.750 10.00 77.6
(300 x 300 x 250) (323,9 x 323,9 x 273,0) (254,0) (35,2)
NOTES
a. Figure 323 not available for the EMEA market.

FIGURE 10 (3 OF 3)
FIGURE 323 FABRICATED GROOVE X GROOVE X MALE THREAD REDUCING TEES (SEGMENT WELDED)
NOMINAL DIMENSIONS
 TFP1815
Page 17 of 26

Nominal Pipe Size

Approx.
E to E
Weight
Inches
Pipe O.D. Lbs.
ANSI Inches (mm)
Inches (kg)
(DN) (mm)

1-1/2 x 1 1.90 x 1.31 2.50 0.6

(40 x 25) (48,3 x 33,7) (63,5) (0,3)
2 x 3/4 2.37 x 1.05 2.50 1.0
(50 x 20) (60,3 x 26,7) (63,5) (0,5)
2x1 2.37 x 1.31 2.50 0.8
(50 x 25) (60,3 x 33,4) (63,5) (0,4)
2 x 1-1/4 2.37 x 1.66 2.50 0.8
(50 x 32) (60,3 x 42,4) (63,5) (0,4)
2 x 1-1/2 2.37 x 1.90 2.50 0.8
(50 x 40) (60,3 x 48,3) (63,5) (0,4)
2-1/2 x 1 2.87 x 1.31 2.50 0.9
(65 x 25) (73,0 x 33,4) (63,5) (0,4)
2-1/2 x 1-1/4 2.87 x 1.66 2.50 1.0
(65 x 32) (73,0 x 42,4) (63,5) (0,5)
2-1/2 x 1-1/2 2.87 x 1.90 2.50 1.3
(65 x 40) (73,0 x 48,3) (63,5) (0,6)
2-1/2 x 2 2.87 x 2.37 2.50 1.2
(65 x 50) (73,0 x 60,3) (63,5) (0,5)
76,1mm x 1-1/4 3.00 x 1.66 2.50 1.0 E to E
(65 x 32) (76,1 x 42,4) (63,5) (0,5)
76,1mm x 1-1/2 3.00 x 1.90 2.50 1.1
(65 x 40) (76,1 x 48,3) (63,5) (0,5)
76,1mm x 2 3.00 x 2.37 2.50 1.2
(65 x 50) (76,1 x 60,3) (63,5) (0,5)
3 x 3/4 3.50 x 1.05 2.50 1.1
(80 x 20) (88,9 x 26,7) (63,5) (0,5)
3x1 3.50 x 1.31 2.50 1.3
(80 x 25) (88,9 x 33,4) (63,5) (0,6)
3 x 1-1/4 3.50 x 1.66 2.5 1.3
(80 x 32) (88,9 x 42,4) (63,5) (0,6)
3 x 1-1/2 3.50 x 1.90 2.50 1.3
(80 x 40) (88,9 x 48,3) (63.5) (0,6)
3x2 3.50 x 2.37 2.50 1.3
(80 x 50) (88,9 x 60,3) (63.5) (0,6)
3 x 2-1/2 3.50 x 2.87 2.50 1.5
(80 x 65) (88,9 x 73,0) (63.5) (0,7)
3 x 76,1mm 3.50 x 3.00 2.50 1.5
(80 x 65) (88,9 x 76,1) (63.5) (0,7)
4x1 4.50 x 1.31 3.00 1.8
(100 x 25) (114,3 x 33,4) (76,2) (0,8)
4 x 1-1/4 4.50 x 1.66 3.00 2.0
(100 x 32) (114,3 x 42,4) (76,2) (0,9)
4 x 1-1/2 4.50 x 1.90 3.00 2.3
(100 x 40) (114,3 x 48,3) (76,2) (1,0)
4x2 4.50 x 2.37 3.00 2.3
(100 x 50) (114,3 x 60,3) (76,2) (1,0)
4 x 2-1/2 4.50 x 2.87 3.00 2.3
(100 x 65) (114,3 x 73,0) (76,2) (1,0)
NOTES
a. Figure 372 not available for the EMEA market.

FIGURE 11 (1 OF 2)
FIGURE 372 FABRICATED CONCENTRIC REDUCER GROOVE X MALE THREAD (MPT)
NOMINAL DIMENSIONS
TFP1815
Page 18 of 26

Nominal Pipe Size

Approx.
E to E
Weight
Inches
Pipe O.D. Lbs.
ANSI Inches (mm)
Inches (kg)
(DN) (mm)

4x3 4.50 x 3.50 3.00 2.6

(100 x 80) (114,3 x 88,9) (76,2) (1,2)
5x4 5.56 x 4.50 3.50 4.5
(125 x 100) (141,3 x 114,3) (88,9) (2,0)
165,1mm x 1 6.50 x 1.31 4.00 1.2
(150 x 25) (165,1 x 33,4) (101,6) (0,5)
165,1mm x 2 6.50 x 2.37 4.00 5.5
(150 x 50) (165,1 x 60,3) (101,6) (2,5)
165,1mm x 76,1mm 6.50 x 3.00 4.00 5.7
(150 x 65) (165,1 x 76,1) (101,6) (2,6)
E to E
165,1mm x 3 6.50 x 3.50 4.00 5.8
(150 x 50) (165,1 x 88,9) (101,6) (2,6)
165,1mm x 4 6.50 x 4.50 4.00 5.8
(150 x 50) (165,1 x 114,3) (101,6) (2,6)
165,1mm x 5 6.50 x 5.563 4.00 5.8
(150 x 50) (165,1 x 141,3) (101,6) (2,6)
6x1 6.63 x 1.31 4.00 5.2
(150 x 25) (168,3 x 33,4) (101,6) (2,4)
6x2 6.63 x 2.37 4.00 5.4
(150 x 50) (168,3 x 60,3) (101,6) (2,4)
6 x 2-1/2 6.63 x 2.87 4.00 5.6
(150 x 65) (168,3 x 73,0) (101,6) (2,5)
6 x 76,1mm 6.63 x 3.00 4.00 5.8
(150 x 65) (168,3 x 76,1) (101,6) (2,6)
6x3 6.63 x 3.50 4.00 6.0
(150 x 80) (168,3 x 88,9) (101,6) (2,7)
6x4 6.63 x 4.50 4.00 6.2
(150 x 100) (168,3 x 114,3) (101,6) (2,8)
6x5 6.63 x 5.56 4.00 6.7
(150 x 125) (168,3 x 141,3) (101,6) (3,0)
NOTES
a. Figure 372 not available for the EMEA market.

FIGURE 11 (2 OF 2)
FIGURE 372 FABRICATED CONCENTRIC REDUCER GROOVE X MALE THREAD (MPT)
NOMINAL DIMENSIONS
 TFP1815
Page 19 of 26

Nominal Pipe Size Figures 211, 311, & 511 Figures 212, 312, & 512

O.D. Nominal Approx. Nominal Approx.

ANSI Inches C to E Weight C to E Weight
Inches
(DN) Inches Lbs. Inches Lbs.
(mm) (mm) (kg) (mm) (kg)
1-1/4 1.660 1.38 0.4 1.75 0.4
(32) (42,4) (35,1) (0,2) (44,5) (0,2)
1-1/2 1.900 1.38 0.5 1.75 0.5
(40) (48,3) (35,1) (0,2) (44,5) (0,2) C to E

2 2.375 1.38 0.6 1.88 0.6

(50) (60,3) (35,1) (0,3) (47,8) (0,3)
2-1/2a 2.875 1.50 1.1 2.00 0.7
(65)b (73,0) (38,1) (0,5) (50,8) (0.3)
FIGURES 211, 311, & 511
76,1mm 3.000 1.50 1.1 2.00 1.2 FABRICATED 11¼° ELBOW
(65) (76,1) (38,1) (0,5) (50,8) (0,5) (SEGMENT WELDED)
3 3.500 1.50 1.2 2.25 1.4
(80) (88,9) (38,1) (0,5) (57,2) (0,6) C to E

4 4.500 1.75 2.2 2.63 2.4

(100) (114,3) (44,5) (1,0) (66,8) (1,1)
139,7mm 5.500 2.00 2.3 2.88 2.5
(125) (139,7) (50,8) (1,0) (73,2) (1,1)
5 5.563 2.00 3.3 2.88 4.1
(125) (141,3) (50,8) (1,5) (73,2) (1,9) FIGURES 212, 312, & 512
FABRICATED 22½° ELBOW
165,1mm 6.500 2.00 3.5 3.13 4.3 (SEGMENT WELDED)
(150) (165,1) (50.8) (1,6) (79,5) (2,0)
6 6.625 2.00 4.6 3.13 5.6
(150) (168,3) (50.8) (2,1) (79,5) (2,5)
8 8.625 2.00 8.7 3.88 11.1
(200) (219,1) (50,8) (3,9) (98,6) (5,0)
10 10.750 2.13 9.1 4.38 14.0
(250) (273,0) (54,1) (4,1) (111,3) (6,4)
12 12.750 2.25 16.7 4.88 22.0
(300) (323,9) (57,2) (7,6) (124,0) (10,0)
NOTES
a. Nominal Pipe Size 2-1/2 in. no longer Figure 311.
b. Nominal Pipe Size 2-1/2 in. no longer Figure 312.

FIGURE 12
FIGURES 211, 311, AND 511 FABRICATED ELBOWS AND FIGURES 212, 312, AND 512 FABRICATED ELBOWS
NOMINAL DIMENSIONS
TFP1815
Page 20 of 26

Nominal Pipe Size Figures 391, 392 & 393 a

Nominal Approx.
E to E ANSI Inches O.D. Inches E to E Weight
(DN) (mm) Inches Lbs.
(mm) (kg)
1-1/4 1.660 4.00 0.8
(32) (42,4) (101,6) (0,4)
1-1/2 1.900 4.00 0.9
FIGURE 391a (40) (48,3) (101,6) (0,4)
FABRICATED
ADAPTER NIPPLE 2b 2.375 4.00 1.2
GROOVE X MALE THREAD (50) (60,3) (101,6) (0,5)
(MA)
2-1/2b 2.875 4.00 1.9
(65) (73,0) (101,6) (0,9)
E to E
76,1mm 3.000 4.00 1.9
(65) (76,1) (101,6) (0,9)
3 3.500 4.00 2.5
(80) (88,9) (101,6) (1,1)
FIGURE 392a 4 4.500 6.00 5.5
FABRICATED (100) (114,3) (154,4) (2,5)
ADAPTER NIPPLE
GROOVE X GROOVE 139,7mm 5.500 6.00 5.6
(125) (139,7) (154,4) (2,5)
E to E 5 5.563 6.00 7.4
(125) (141,3) (154,4) (3,4)
165,1mm 6.500 6.00 7.6
(150) (165,1) (154,4) (3,4)
6 6.625 6.00 9.5
FIGURE 393a (150) (168,3) (154,4) (4,3)
FABRICATED 8 8.625 6.00 14.2
ADAPTER NIPPLE (200) (219,1) (154,4) (6,4)
GROOVE X PLAIN
10 10.750 8.00 27.0
(250) (273,0) (203,2) (12,2)
12 12.750 8.00 33.0
(300) (323,9) (203,2) (15,0)
NOTES
a. Figure 391, Figure 392, and Figure 393 are not available for the EMEA market.
b. Figure 391 2 in. x 4 in. (DN50 x DN100) and 2-1/2 in. x 4 in. (DN65 x DN100) are
cast.

FIGURE 13
FIGURES 391, 392, AND 393 FABRICATED ADAPTER NIPPLES
NOMINAL DIMENSIONS
 TFP1815
Page 21 of 26

Nominal Nominal Approx.

O.D.
ANSI Inches C to GE C to TE Weight
Inches
(DN) Inches Inches Lbs.
(mm) (mm) (mm) (kg
C to TE
5x5x8 5.563 x 5.563 x 8.625 13.313 9.313 27.8
(125 X 125 X 200) (141,3 x 141,3 x 219,1) (388,14) (236,55) (12,6)
6x6x8 6.625 x 6.625 x 8.625 13.313 8.750 36.7
(150 X 150 X 200) (168,3 x 168,3 x 219,1) (388,14) (222,25) (16,4) C to GE
NOTES
a. Figure 507/50L not available for the EMEA market.

FIGURE 14
FIGURE 507/50L FABRICATED BULLHEAD TEE
NOMINAL DIMENSIONS

Nominal Nominal Approx.

O.D. C to TE
ANSI Inches C to GE C to TE Weight
Inches
(DN) Inches Inches Lbs.
(mm) (mm) (mm) (kg)
4 x 4 x 2-1/2 5.563 x 5.563 x 8.625 13.313 9.313 8.7
(100 X 100 X 65) (141,3 x 141,3 x 219,1) (388,14) (236,55) (3,9)
6 x 6 x 2-1/2 6.625 x 6.625 x 8.625 13.313 8.750 13.7 C to GE
(150 X 50 X 65) (168,3 x 168,3 x 219,1) (388,14) (222,25) (6,2)
NOTES
a. Figure 328 not available for the EMEA and APAC market.
FIGURE 15
FIGURE 328 FABRICATED STANDPIPE TEE
NOMINAL DIMENSIONS
TFP1815
Page 22 of 26

Friction Resistance

Nominal Pipe Size

Elbows Elbows Tee(1) Tee
90° 45° Branch Run
O.D. Feet Feet Feet Feet
ANSI Inches (m) (m) (m) (m)
Inches
(DN) (mm)

1 1.31 1.3 0.8 3.7 1.3

(25) (33,4) (0,4) (0.3) (1,1) (0.6)
1-1/4 1.7 1.9 1.0 4.8 1.9
(32) (42,4) (0,6) (0,3) (1,5) (0,6)
1-1/2 1.9 2.3 1.2 5.8 2.3
(40) (48,3) (0,7) (0,4) (1,8) (0,7)
2 2.4 3.2 1.6 8.0 3.2
(50) (60,3) (1,0) (0,5) (2,5) (1,0)
2-1/2 2.9 3.9 2.0 9.8 3.9
(65) (73,0) (1,2) (0,6) (3,0) (1,2)
– 3.0 4.1 2.1 10.3 4.1
(65) (76,1) (1,2) (0,6) (3,1) (1,2)
3 3.5 4.9 2.4 12.2 4.9
(80) (88,9) (1,5) (0,7) (3,7) (1,5)
4 4.5 6.5 3.3 16.3 6.5
(100) (114,3) (2,0) (1,0) (5,0) (2,0)
– 5.5 8.0 4.1 20.0 8.0
(125) (139,7) (2,4) (1,3) (6,1) (2,4)
5 5.6 8.2 4.1 20.5 8.2
(125) (141,3) (2,5) (1,3) (6,3) (2,5)
– 6.5 9.5 4.8 23.8 9.5
(150) (165,1) (2,9) (1,4) (7,2) (2,9)
6 6.6 9.9 5.0 24.8 9.9
(150) (168,3) (3,0) (1,5) (7,6) (3,0)
8 8.6 13.1 6.6 32.8 13.1
(200) (219,1) (4,0) (2,0) (10,0) (4,0)
10 10.8 16.5 8.3 41.3 16.5
(250) (273,0) (5,0) (2,5) (12,6) (5,0)
12 12.8 19.9 9.9 49.7 19.9
(300) (323,9) (6,1) (3,0) (15,1) (6,1)
NOTES
a. For the reducing tee branches, use the value that is corresponding to the branch size.
Example:
For 8 in. x 8 in. x 2 in. tee, the branch value of 2 in. is 8.0 feet.
For sizes not listed interpolate from the values shown.

TABLE A
FRICTION RESISTANCE FOR
FIGURES 501, 510, 510DE AND 519
(EXPRESSED AS EQUIVALENT STRAIGHT PIPE)
 TFP1815
Page 23 of 26

Friction Resistance

Nominal Pipe Size

Elbows Elbows Tee* Tee
90° 45° Branch Run
O.D. Feet Feet Feet Feet
ANSI Inches (m) (m) (m) (m)
Inches
(DN) (mm)

2 2.4 3.5 1.6 8.0 3.2

(50) (60,3) (1,1) (0,5) (2,4) (1,0)
2-1/2 2.9 4.3 2.0 9.8 3.9
(65) (73,0) (1,3) (0,6) (3,0) (1,2)
– 3.0 4.3 2.1 10.3 4.1
(65) (76,1) (1,3) (0,6) (3,1) (1,2)
3 3.5 5.0 2.4 12.2 4.9
(80) (88,9) (1,5) (0,7) (3,7) (1,5)
4 4.5 6.7 3.3 16.3 6.5
(100) (114,3) (2,0) (1,0) (5,0) (2,0)
– 5.5 8.3 4.1 20.0 8.0
(125) (139,7) (2,5) (1,2) (6,1) (2,4)
5 5.6 8.5 4.3 21.5 8.6
(125) (141,3) (2,5) (1,3) (6,5) (2,6)
– 6.5 9.6 4.8 23.8 9.5
(150) (165,1) (2,9) (1,5) (7,3) (2,9)
6 6.6 10.0 5.0 24.8 9.9
(150) (168,3) (3,0) (1,5) (7,6) (3,0)
8 8.6 13.1 6.6 32.8 13.0
(200) (219,1) (4,0) (2,0) (10,0) (4,0)

TABLE B
FRICTION RESISTANCE FOR FIGURES 510S AND 519S
(EXPRESSED AS EQUIVALENT LENGTH OF STRAIGHT SCHEDULE 40 STEEL PIPE)
TFP1815
Page 24 of 26

Figure 501 Figure 510 Figure 519

Nominal Pipe Cast 45° Elbow Cast 90° Elbow Cast Tee
Size psi psi psi
bar bar bar

Ansi O.D.
Inches Inches UL FM VdS LPCB UL FM VdS LPCB UL FM VdS LPCB
(DN) mm

1 1.31 — — — — — — — — — — — —
(25) (33,4)
1-1/4 1.66 365 365 232 290 365 232 290
— — — — —
(32) (42,4) (25,2) (25,2) (16,0) (20,0) (25,2) (16,0) (20,0)
1-1/2 1.90 365 365 232 290 365 232 290
— — — — —
(40) (48,3) (25,2) (25,2) (16,0) (20,0) (25,2) (16,0) (20,0)
2 2.37 365 365 232 290 365 365 232 290 365 365 232 290
(50) (60,3) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
2-1/2 2.87 365 365 365 365 365 365
— — — — — —
(65) (73,0) (25,2) (25,2) (25,2) (25,2) (25,2) (25,2)
76,1mm 3.00 365 365 232 290 365 365 232 290 365 365 232 290
(65) (76,1) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
3 3.50 365 365 232 290 365 365 232 290 365 365 232 290
(80) (88,9) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
4 4.50 365 365 232 290 365 365 232 290 365 365 232 290
(100) (114,3) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
139,7mm 5.50 365 365 232 365 365 232 365 365 232
— — —
(125) (139,7) (25,2) (25,2) (16,0) (25,2) (25,2) (16,0) (25,2) (25,2) (16,0)
5 5.56 365 365 365
— — — — — — — — —
(125) (141,3) (25,2) (25,2) (25,2)
165,1mm 6.50 365 365 290 365 365 290 365 365 290
— — —
(150) (165,1) (25,2) (25,2) (20,0) (25,2) (25,2) (20,0) (25,2) (25,2) (20,0)
6 6.63 365 365 232 290 365 365 232 290 365 365 232 290
(150) (168,3) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
8 8.63 365 365 232 290 365 365 232 290 365 365 232 290
(200) (219,1) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
10 10.75 450 232 290 450 232 290 450 232 290
— — —
(250)a (273,0) (31,0) (16,0) (20,0) (31,0) (16,0) (20,0) (31,0) (16,0) (20,0)
12 12.75 450 232 290 450 232 290 450 232 290
— — —
(300)a (323,9) (31,0) (16,0) (20,0) (31,0) (16,0) (20,0) (31,0) (16,0) (20,0)
NOTES
a. Marked as Grinnell.

TABLE C
FIGURE 501 AND FIGURE 510 CAST ELBOWS, AND 519 CAST TEE
LISTED/APPROVED PRESSURE RATING
 TFP1815
Page 25 of 26

Figure 260 Figure 510S Figure 519S

Nominal Pipe Cast End Cap Cast 90° Elbow Cast Tee
Size psi psi psi
bar bar bar

Ansi O.D.
Inches Inches UL FM VdS LPCB UL FM VdS LPCB UL FM VdS LPCB
(DN) (mm)

1 1.31 500 — — — — — — — — — — —
(25) (33,4) (34,5)
1-1/4 1.66 500 500 — — — — — — — — — —
(32) (42,4) (34,5) (34,5)
1-1/2 1.90 500 500 — — — — — — — — — —
(40) (48,3) (34,5) (34,5)
2 2.37 500 500 365 365 232 290 365 365 232 290
— —
(50) (60,3) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
2-1/2 2.87 500 500 365 365 365 365
— — — — — —
(65) (73,0) (34,5) (34,5) (25,2) (25,2) (25,2) (25,2)
76,1mm 3.00 500 500 365 365 232 290 365 365 290
— — —
(65) (76,1) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (20,0)
3 3.50 500 500 365 365 232 290 365 365 232 290
— —
(80) (88,9) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
4 4.50 500 500 365 365 232 290 365 365 232 290
— —
(100) (114,3) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
139,7mm 5.50 500 500 365 365 232 365 365 232
— — — —
(125) (139,7) (34,5) (34,5) (25,2) (25,2) (16,0) (25,2) (25,2) (16,0)
5 5.56 500 500 365 365
— — — — — — — —
(125) (141,3) (34,5) (34,5) (25,2) (25,2)
165,1mm 6.50 500 500 365 365 365 365
— — — — — —
(150) (165,1) (34,5) (34,5) (25,2) (25,2) (25,2) (25,2)
6 6.63 500 500 365 365 232 290 365 365 232 290
— —
(150) (168,3) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
8 8.63 500 500 365 365 232 290 365 365 232 290
— —
(200) (219,1) (34,5) (34,5) (25,2) (25,2) (16,0) (20,0) (25,2) (25,2) (16,0) (20,0)
10 10.75 500 500 — — — — — — — — — —
(250) (273,0) (34,5) (34,5)
12 12.75 500 500 — — — — — — — — — —
(300) (323,9) (34,5) (34,5)

TABLE D
FIGURE 260 CAST END CAP, FIGURE 510S CAST ELBOW, AND FIGURE 519S CAST TEE
LISTED/APPROVED PRESSURE RATING
TFP1815
Page 26 of 26

Nominal Pipe ADACAP Care and

Maintenance
psi
Size bar

The following inspection procedure

Inches x NPT UL FM VdS LPCB must be performed as indicated, in
(DN)
addition to any specific requirements
of the NFPA. Any impairments must be
1-1/2 x 1/2 300 300 immediately corrected.
— —
(40) (20,7) (20,7)
1-1/2 x 3/4 300 300 Before closing a fire protection system
— — main control valve for maintenance
(40) (20,7) (20,7)
work on the fire protection system
1-1/2 x 1 300 300 that it controls, obtain permission to
— —
(40) (20,7) (20,7)
shut down the affected fire protection
2 x 1/2 300 300 — — system from the proper authorities
(50) (20,7) (20,7) and notify all personnel who may be
2 x 3/4 300 300 affected by this decision.
— —
(50) (20,7) (20,7) The owner is responsible for the
2x1 300 300 inspection, testing, and maintenance of
— —
(50) (20,7) (20,7) their fire protection system and devices
2-1/2 x 1/2 300 300 in compliance with this document, as
— — well as with the applicable standards
(65) (20,7) (20,7)
of the NATIONAL FIRE PROTECTION
2-1/2 x 3/4 300 300 ASSOCIATION, for example, NFPA
— —
(65) (20,7) (20,7)
25, in addition to the standards of any
2-1/2 x 1 300 300 — — authority having jurisdiction. Contact
(65) (20,7) (20,7) the installing contractor or product
TABLE E manufacturer with any questions.
ADACAP Automatic sprinkler systems are rec-
LISTED/APPROVED PRESSURE RATING ommended to be inspected, tested,
and maintained by a qualified Inspec-
tion Service in accordance with local
requirements and/or national codes.
After placing a fire protection system
in service, notify the proper authorities
and advise those responsible for moni-
toring proprietary and/or central station
alarms.

Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.

Ordering
Procedure
GRINNELL Products are available glob-
ally through a network of distribution
centers. For the nearest distributor, visit
www.grinnell.com.
When placing an order, indicate the full
product name. Specify the quantity,
figure number, wall thickness, and size.

1467 Elmwood Avenue, Cranston, RI 02910 | Telephone +1-401-781-8220

© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.

NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
 Worldwide
www.tyco-fire.com
Contacts

TFP1815
Change History Appendix

ISSUE DATE NOTES

Page 1, added QR code and URL to allow convenient access to electronic version from printed docu-
ment; Page 26, changed corporate address and telephone number to 1467 Elmwood Avenue, Crans-
08-22
ton, RI 02910 | Telephone +1-401-781-8220, formerly 1400 Pennbrook Parkway, Lansdale, PA 19446 |
Telephone +1-215-362-0700.
Updated NOTICE in General Description to add statement advising customers internal protective coat-
10-21 ings can become separated from fittings during system operation, potentially causing blockage in
systems equipped with strainers or filters featuring mesh sizes less than 5/32 in. (4 mm).
Updated Figure 391 Adapter Nipple Groove x Male Thread sizes 2 in. (DN50) and 2-1/2 in. (DN65) to
04-21
indicate they cast; formerly shown as fabricated.
Moved dimension and weight data of 2 in. x 1-1/4 in. (DN50 x DN32) and 2 in. x 1-1/2 in. (DN50 x DN40)
sizes to Figure 550 Concentric Reducer; formerly Figure 350 (not offered); Added 2 in. (DN50), 2-1/2 in.
02-21 (DN65) and 4 in. (DN100) size to Figure 227 Cross; Removed 2-1/2 in. (DN65) size from Figure 311 11-1/4°
and Figure 312 22-1/2° Elbows; Added agency Listed and Approved pressure ratings for 10 in. (DN250)
and 12 in. (DN300) sizes to Figure 501 45° and Figure 510 90° Elbows and Figure 519 Tee.
Standardized nominal pipe size values for metric fittings and mixed imperial and metric reducing fittings,
12-20
including 76,1mm, 108,0mm, 139,7mm, 165,1mm and 216,3mm.
Added carbon steel specifications to Technical Data Material sub-section for fabricated fittings; Updated
08-19
document title to reflect iron and steel materials.
Added new sizes: Figure 250 Cast Concentric Reducer; Figure 510 Cast 90 Elbow; Figure 519 Cast Tee;
03-19
Figure 260 Cast End Cap.
Updated Grinnell® branding and document format; Added Johnson Controls copyright; Added dis-
08-18 claimer stating specifications and information subject to change without notice; Added reference to
Regulatory and Health Warning Technical Data Sheet TFP2300.
Corrected C to E dimension for 8 in. (DN200) Figure 501 45º Elbow to 4.25 in. (108,0 mm), formerly 4.5
05-17
in. (108,0 mm).
Updated fitting weights; Expanded variety of fittings and available sizes; Clarified regional availability
01-16
of protective coatings.
07-12 New Technical Data Sheet TFP1815 describes Grinnell G-FIRE Grooved Fittings.

1467 Elmwood Avenue, Cranston, RI 02910 | Telephone +1-401-781-8220

© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.