ISO 9001, ISO 14001 & OHSAS 18001 Certified
Product Data Sheet Simathane Gloss 3500-00
Last update: September 2021
Description Two components aliphatic polyurethane coating with excellent gloss
and colour retention.
Principal Characteristics Excellent resistance to atmospheric exposure
Non chalking and non yellowing
Resistant to splash of mild chemicals
Good resistant to water and solvent
Easily over coated over extended periods
Resistant to impact, abrasion in marine and industrial corrosive
atmosphere
Recommended use As a deluxe finishing coat on a wide variety of any substrate especially
in marine and industrial atmosphere
Specification data on 20 0C
Gloss High gloss
Colour White and colour, see standard colour card.
Specific gravity 1.20 +0.15 [g/mL]
Solids by volume 56 2 %
Recommended Dry film thickness : 50-75 micron
Wet film thickness : 89-134 microns
Coverage theoretical 7.4 m2/ litre - 75 micron
Drying time Touch Dry : 3 Hours at 30 0C
Hard Dry : 7 Hours
Pot Life 7 Hours (after mixing components)
Full cure 7 days
Painting interval Min : 12 hours ; max : unlimited
VOC 454 g/litre (base), 271 g/litre (hardener)
Shelf Life 12 months (cool and dry place)
Flash point (DIN 53213) Base = 25,3 0C, Hardener = 38 0C
Service Temperature Continuous : 100 oC
Periodic : up to 120°C
Surface Preparation
Substrate Recommended
New Steel Blast Cleaned SSPC-SP10 ISO Sa2 ½
The surface to be painted Must be clean, free from rust, oil grease or other foreign
matter using wash, detergent, or solvent wipe.
Preceding coat : SIMACOVER EP PRIMER or SIMACOVER EP COATING
TRUST, PROTECT AND COMMIT Page 1 of 2
ISO 9001, ISO 14001 & OHSAS 18001 Certified
Product Data Sheet Simathane Gloss 3500-00
Last update: September 2021
Application instruction
Condition Recommended
Temperatur Min 100C, max 350C
Relative humidity Max 85 %
Substrate temperature should be at least 30C above dew point.
Mixing ratio Base : Hardener = 7 : 1 [by volume]
temperature of the mixture should be above 150C
Thinner Sima Thinner 43-00
should be added after mixing the components, and stir well before
use preferable by means of mechanical mixer. Too much solvent
result in lower sag resistance and slower cure.
Method of application Thinner Nozzle Orifice Nozzle Pressure
1. Airless spray Max 10 % 0.018 (0.46 mm) 150 Bar (2100 psi)
2. Air Spray 10-15% 2 mm 4 Bar/57 psi
3. Brush Max 5 % - -
Packing and size instruction
Packing size (two packs product) : 5 and 20 litres
Storage The product must be storage in accordance with national
regulation. Preferred storage condition are to keep the
containers in the dry space provided with adequate ventilation.
The containers should be sealed tightly.
Safety Precaution Wear suitable protective clothing such as overalls, goggles, dust
mask and gloves. Ventilation shall be maintained from coating
application until the completion of curing in order to remove
residue of solvents and promote curing. Do not breathe the
vapour or spray. This product is flammable. Keep away from
sources of ignition. Do not smoke.
HEALTH AND SAFETY: For detailed information on the health and safety hazards and precaution for
use of this product, please see the SAFETY DATA SHEET (SDS).
The information in this data sheet is to the best our knowledge connects at date printing. The company reserves the right to the modify data without notice. Any
change in data will normally be followed by issued of new data sheet. The user should check the data of printing and if more than 12 months have elapsed, then the
data should on only be used after checking with our nearest self-office to establish that they are still valid. Since condition of application and services may be
beyond our control, no liability can accept on basis of this data.
TRUST, PROTECT AND COMMIT Page 2 of 2
